subwoofer HCCA 10.2 10.4 12.2 12.4 15.2...

subwoofer

10.2 10.412.2 12.415.2 15.4

HCCA 10.2 10.412.2 12.415.2 15.4

HCCA

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Tools of the Trade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Finding Speaker Mounting Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Re-cone Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Wiring Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Parallel—One Speaker (dual 2 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Parallel—Two Speakers (dual 4 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Parallel—One Speaker (dual 4 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Series-Parallel—Two Speakers (dual 2 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Series-Parallel—Three Speakers (dual 4 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Series—One Speaker (dual 2 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Series-Parallel—Four Speakers (dual 4 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Series-Parallel—Four Speakers (dual 2 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

2 Amplifiers—One Speaker (dual 2 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

2 Amplifiers—One Speaker (dual 4 ohm voice coils) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Enclosure Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

HCCA 10.2 & 10.4 Sealed Enclosure Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

HCCA 10.2 & 10.4 Vented Enclosure Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . .19





Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Specifications (Cont’d) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

2

INTRODUCTION

Thank you for your purchase of the Orion HCCA SubWoofers. These woofersrepresent a combination of incredible performance and value. The HCCA seriessubwoofers feature a massive 4" voice coil and triple stacked magnet assembly tomaximize excursion and output. Capable of maintaining their balance atexceptionally high output levels. These high-performance woofers are built with dual2 or 4 ohm voice coils, to get the most out of your amplifier. They are available instandard 10”, 12” and 15” sizes.

We at Orion strive to give you all the latest up to date information about this product.What we can’t give you in this manual is personal installation or technical experience.If you have questions concerning the use or application of this product, please referto the nearest Authorized ORION Dealer for assistance, visit www.orioncaraudio.com,or call the Orion technical support hotline at 1-800-876-0800. As we are alwaysfinding new ways to improve our product, the features and specifications are subjectto change without notice.

PRACTICE SAFE SOUND™

Continuous exposure to sound pressure levels over 100dB may cause permanenthearing loss. High powered automotive sound systems can generate sound pressurelevels in excess of 130dB. When playing your system at high levels, please use hearingprotection and prevent long term exposure.

INSTALLATION

The performance of these HCCA subwoofers is directly proportional to the quality ofinstallation. Care taken during the installation process will be rewarded with years ofsatisfying performance. If you are unsure about your installation capabilities, pleaserefer to your local Authorized Orion Dealer for technical assistance. Orion dealers aretrained professionals dedicated to extracting the maximum performance out of yourOrion system. If you decide to install this speaker system yourself, please read theentire section on sealed and vented enclosures before starting your installation.

Please Note: Due to the extremely long excursion and high temperature possibilitiesof this woofer, it is recommended that when the woofer is installed it be positionedso that the cone either faces upward or downward only.

3

TOOLS OF THE TRADE

Listed are the majority of the tools required to perform the installation. Having theproper tools will make the installation much easier. It is very difficult when you gethalf way through the installation and discover that you require a specific tool to getyourself through a particular part of the installation. Some of these tools arenecessities. Some make the job much easier.

• Marking Pen • Electric Drill• Assorted Drill Bits • Phillips Screwdriver• Allen wrenches • Volt/Ohm Meter (Optional)• Wire Strippers • Wire Cutters• Table saw • Wire Crimper• Jig saw

FINDING SPEAKER MOUNTING LOCATIONS

Choosing the correct speaker locations will have the greatest effect on the soundquality of the system. There are many different considerations needed when choosingthe locations that best suit your needs. The locations must be large enough for thespeakers to fit. Care is needed to ensure that the location you have chosen will notaffect any of the mechanical or electrical operations of the vehicle.

Determining the best location for the speakers will depend on your cosmetic needsand your vehicle's interior. Usually the woofers are installed in the trunk, rear seat, orrear of the vehicle.

FEATURES

1 2

43

567

8

9

10

13

14

1615

17

181920

21

12 11

4

5

1. Paper dust cap - moisture and UV resistant.

12. Voice coil gap vents. Part of the enhanced voice coil cooling system (forced convection - aluminum heat sinking -shorting rings to reduce inductive heating).

2. Tall, wide, balanced, NBR Foam (high density expanded polyester foam) surround for linear controlled long excursion using a Tri Radius symmetrical edge design optimized on non-linear FEA.

13. Cast aluminum rear pole piece heat sink with fins and vent holes. Part of the enhanced voice coil cooling system (forced convection - aluminum heat sinking).

3. Paper cone - moisture and UVresistant.

14. High temperature (Polyester Amide Amide Resin Coated) Copper clad Aluminum voice coil wound on an aluminum former (10" uses 3" voice coil, 12 & 15 use a 4" voice coil) Dual 2 and 4 ohm voice coils available.

4. Custom Cast Aluminum frame. 15. Screen meshed areas to allow venting below spider to and keep foreign object out of the voice coil gap.

5. Spider ring attachment screws. Part of re-cone feature (8 hex screws).

16. Cast aluminum top pole piece heat sink with fins and vent hole. Part of the enhanced voice coil cooling system (forced convection-aluminum heat sinking-shorting rings to reduce inductive heating).

6. aluminum voice coil former (10" uses 3" voice coil former, 12 & 15 use a 4" voice coil former).

17. Bottom flat interlaced Conex spider with stitched and looped tinsel leads attached.

7. Venting in Voice coil former. Part of the enhanced voice coil cooling system (forced convection).

18. Custom allen head screw terminals. A pair on each side (one pair foreach voice coil).

8. 11mm Steel front plate. 19. Spider spacer and spider mounting ring assembly part of field re-conekit attachment method. (eight allenhead screws).

9. Large 3 stack ceramic magnets (10" 264 oz 12/15" 445 oz).

20. Top flat interlaced Conex spider.

10. 11mm Steel back plate / pole piece T yoke assembly.

21. Surround clamp ring, part of field re-cone kit attachment method. (eight allen head screws).

11. 1.25" vent. Part of the enhanced voice coil cooling system (forced convection - aluminum heat sinking -shorting rings to reduce inductive heating).

6

RE-CONE KIT

A re-cone kit is available for these speakers and can be obtained from your dealer. Thepart number for each model is listed below.

WIRING CONFIGURATIONS

The following illustrations provide guidelines on properly connecting your HCCAOrion woofer to an Orion amplifier for maximum power and performance usingcommon parallel, and series/parallel wiring configurations.

Recommended Amplifier Power

1 woofer 1,200 to 4,000 watts

2 woofers 2,400 to 8,000 watts



Model Description Re-cone Kit p/nHCCA10.2CK ORION HCCA 10" 2 OHM Re-Cone Kit 27902HCCA10.4CK ORION HCCA 10" 4 OHM Re-Cone Kit 27904HCCA12.2CK ORION HCCA 12" 2 OHM Re-Cone Kit 27907HCCA12.4CK ORION HCCA 12" 4 OHM Re-Cone Kit 27909HCCA15.2CK ORION HCCA 15" 2 OHM Re-Cone Kit 27912HCCA15.4CK ORION HCCA 15" 4 OHM Re-Cone Kit 27914

7

Parallel—One Speaker (dual 2 ohm voice coils)One dual 2 ohm voice coil woofer with voice coils in parallel results in a 1 ohm loadto the amplifier.

1. Connect the speaker in parallel by connecting the two positive (+) terminalstogether and the two negative (-) terminals together.

2. Wire the positive (+) terminals of the woofer to the positive (+) terminal on theamplifier. Wire the negative (-) terminals of the woofer to the negative (-) terminalon the amp

2 oh

m

2 oh

m

+ +

- -

+

-

8

Parallel—Two Speakers (dual 4 ohm voice coils)Two dual 4 ohm voice coil woofers with voice coils in parallel and the two woofers inparallel results in a 1 ohm load to the amplifier.

1. Connect the speaker in parallel by connecting the four positive (+) terminalstogether and the four negative (-) terminals together.

2. Wire the positive (+) terminals of the woofers to the positive (+) terminal on theamplifier. Wire the negative (-) terminals of the woofers to the negative (-) terminalon the amplifier.

4 oh

m

4 oh

m

+ +

- -4

ohm

4 oh

m+ +

- -

+

-

9

Parallel—One Speaker (dual 4 ohm voice coils)One dual 4 ohm voice coil woofer with voice coils in parallel results in a 2 ohm loadto the amplifier.

1. Connect the speaker in parallel by connecting the two positive (+) terminalstogether and the two negative (-) terminals together.

2. Wire both positive (+) terminals of the woofer to the positive (+) terminal on theamplifier. Wire both negative (-) terminals of the woofer to the negative (-) terminalon the amplifier.

4 oh

m

4 oh

m

+ +

- -

+

-

10

Series-Parallel—Two Speakers (dual 2 ohm voice coils)Note: Verify and ensure that the woofer wiring is connected as shown withthe negative connection from the first woofer coil connected to the positiveconnection of the second woofer coil.

Two dual 2 ohm voice coil woofers with voice coils in series and then parallel the twoseries woofers results in a 2 ohm load to the amplifier.

1. Connect each woofer in series by connecting the negative (-) of the first coil to thepositive (+) terminal of the second coil.

2. Wire the positive (+) terminal of the first coil on each woofer to the positive (+)terminal on the amplifier. Wire the negative (-) terminal of the second coil on eachwoofer to the negative (-) terminal on the amplifier.

2 oh

m

2 oh

m

+ +

- -

2 oh

m

2 oh

m

+ +

- -

+

-

11

Series-Parallel—Three Speakers (dual 4 ohm voice coils)Note: Verify and ensure that the woofer wiring is connected as shown withthe negative connection from the first woofer coil connected to the positiveconnection of the second woofer coil.

Three dual 4 ohm voice coil woofer with voice coils of each woofer wired in series andthen parallel the three woofers for a resulting 2.67 ohms.load to the amplifier.


2. Wire the positive (+) terminal of each woofer’s first coil to the positive (+) terminalon the amplifier. Wire the negative (-) terminal of each woofer’s second coil to thenegative (-) terminal on theamplifier.

4 oh

m

4 oh

m

+ +

- -

4 oh

m

4 oh

m

+ +

- -

4 oh

m

4 oh

m

+ +

- -

+

-

12

Series—One Speaker (dual 2 ohm voice coils)One dual 2 ohm voice coil woofer with voice coils in connected in series results in a 4ohm load to the amplifier.

1. Connect the woofer in series by connecting the negative (-) of one terminal to thepositive (+) terminal of the other coil.

2. Wire the positive (+) terminal of the first coil to the positive (+) terminal on theamplifier. Wire the negative (-) terminal of the second coil to the negative (-) terminalon the amplifier.

2 oh

m

2 oh

m

+ +

- -

+

-

13

Series-Parallel—Four Speakers (dual 4 ohm voice coils)Note: Verify and ensure that the woofer wiring is connected as shown withthe negative connection from the first woofer coil connected to the positiveconnection of the second woofer coil.

Four dual 4 ohm voice coil woofers should be wired with the voice coils on eachwoofer in series and then parallel the four woofers for a resulting 2 ohm load to theamplifier.


2. Wire the positive (+) terminals of the first coil of each woofer to the positive (+)terminal on the amplifier. Wire the negative (-) terminal of the second coil of eachwoofer to the negative (-) terminal on the amplifier.

4 oh

m

4 oh

m

4 oh

m

4 oh

m

4 oh

m

4 oh

m

4 oh

m

4 oh

m

+

-

+ +

- -

+ +

- -

+ +

- -

+ +

- -

14

Series-Parallel—Four Speakers (dual 2 ohm voice coils)Note: Verify and ensure that the woofer wiring is connected as shown withthe negative connection from the first woofer coil connected to the positiveconnection of the second woofer coil.

Four dual 2 ohm voice coil woofers should be wired with the voice coils on eachwoofer in series and then parallel the four woofers for a resulting 1 ohm load to theamplifier.


2. Wire the positive (+) terminals of the first coil of each woofer to the positive (+)terminal on the amplifier. Wire the negative (-) terminal of the second coil of eachwoofer to the negative (-) terminal on the amplifier.

2 oh

m

2 oh

m

2 oh

m

2 oh

m

2 oh

m

2 oh

m

2 oh

m

2 oh

m

+

-

+ +

- -

+ +

- -

+ +

- -

+ +

- -

15

2 Amplifiers—One Speaker (dual 2 ohm voice coils)One dual 2 ohm voice coil woofer with each voice coil connected to an individualamplifier, resulting in a 2 ohm load to each amplifier.

1. Connect one of the speaker’s voice coils to the first amplifier by connecting thepositive (+) terminal and the negative (-) terminal from the speaker to the respectivepositive (+) terminal and the negative (-) terminal from the first amplifier.

2. Connect the other of the speaker’s voice coils to the second amplifier by connectingthe positive (+) terminal and negative (-) terminal from the speaker to the respectivepositive (+) terminal and the negative (-) terminal from second amplifier.

2 oh

m

2 oh

m

+ +

- -

+

-

+

-

2 Amplifiers—One Speaker (dual 4 ohm voice coils)One dual 4 ohm voice coil woofer with each voice coil connected to an individualamplifier, resulting in a 4 ohm load to each amplifier.

1. Connect one of the speaker’s voice coils to the first amplifier by connecting thepositive (+) terminal and the negative (-) terminal from the speaker to the respectivepositive (+) terminal and the negative (-) terminal from the first amplifier.

2. Connect the other of the speaker’s voice coils to the second amplifier by connectingthe positive (+) terminal and negative (-) terminal from the speaker to the respective

positive (+) terminal and the negative (-) terminal from second amplifier.

4 oh

m

4 oh

m

+ +

- -

+

-

+

-

16

ENCLOSURE DESIGN

This section gives the basic description for a sealed enclosure. Orion HCCA woofersare designed for sealed enclosures and vented enclosures. Sealed enclosures aregenerally considered the most versatile for all music types and are the easiest tobuild. They will also give high power handling with a wider range of frequencies.The enclosure must be absolutely air tight. Use a high quality wood glue for allseams of the enclosure. The enclosure should also be screwed together. Theenclosure should be no less than 3/4" on sides. The baffle board (woofer mountingplate) should be no less than 1". If the woofer mounting is to be recessed then aminimum of two 3/4" plates together should be used. As MDF is a porous materialit is best to also seal the inside of the enclosure.

NOTE: The woofer must face up or down only, especially in sealed enclosures.

NOTE: Refer to the website www.orioncaraudio.com for updated enclosuredata for your woofer application.

17

HCCA 10.2 & 10.4 Sealed Enclosure Recommendations

c

b

—Box Parts—Box Shape – Square Prism1 Top, 1 Bottom depth (c) = 14.5 in. width (b) = 13.5 in. thickness = 1.0 in.1 Front, 1 Back height (a) = 11 in. width (d) = 11.5 in. thickness = 1.0 in.2 Sides height (a) = 11 in. depth (c) = 14.5 in. thickness = 1.0 in.

—Driver Mounting— Front

Top &Bottom

a

d

Front &Back

c

Sides

A

B

C

—External Dimensions—A = 13 in.B = 13.5 in.C = 14.5 in.—Internal Dimensions—A = 11 in.B = 11.5 in.C = 12.5 in.—Wall Thickness—All Sides = 1.0 in.

18


c

b

—Box Parts—Box Shape – Square Prism1 Top, 1 Bottom depth (c) = 16 in. width (b) = 16 in. thickness = 1.0 in.1 Front, 1 Back height (a) = 14.5 in. width (d) = 14 in. thickness = 14 in.2 Sides height (a) = 14.5 in. depth (c) = 16 in. thickness = 1.0 in.


Top &Bottom

a

d

Front &Back

c

Sides

A

B

C

—External Dimensions—A = 16.5 in.B = 16 in.C = 16 in.—Internal Dimensions—A = 14 in.B = 14 in.C = 14 in.—Wall Thickness—All Sides = 1.0 in.

20

22


c

b

—Box Parts—Box Shape – Square Prism1 Top, 1 Bottom depth (c) = 20 in. width (b) = 18 in. thickness = 1.0 in.1 Front, 1 Back height (a) = 15.5 in width (d) = 19 in. thickness = 1.0 in.2 Sides height (a) = 15.5 in depth (c) = 20 in. thickness = 1.0 in.


Top &Bottom

a

d

Front &Back

c

Sides

A

B

C

—External Dimensions—A = 17.5 in.B = 18 in.C = 20 in.—Internal Dimensions—A = 15.5 in.B = 16 in.C = 18 in.—Wall Thickness—All Sides = 1.0 in.

SPECIFICATIONS

Directed Part Number 27302 27304 27307Model Number 10.2 10.4 12.2

Thiele/Small ParametersFs (free-air resonance, Hz) 30.78 32.49 22.56Vas (equivalent compliance, cu. ft. 0.564 0.564 1.847Vas (equivalent compliance, liters) 15.98 15.98 52.33Qms (Q, mechanical) 3.63 3.63 2.99Qes (Q, electrical) 0.42 0.46 0.36Qts (total driver Q) 0.38 0.41 0.32Re (DC resistance, ohms) 3.93 7.57 4.07Z (nominal impedance, ohms) 2 x 2 2 x 4 2 x 2Le (inductance, mh) 1.93 2.93 2.61Efficiency (1W @ 1M, dB) 83 83 85Xmax (one way linear excursion, in.) 1.0 1.0 1.2Xmax (one way linear excursion, mm) 25 25 30Pe (continuous power handling, watts) 1500 1500 2000Peak power handling (music, watts)** 3000 3000 4000Mms (total moving mass, grams) 261.93 235.64 421.18Cms (mechanical compliance, mm/N) 0.102 0.102 0.118Bl (motor strength, Tesla-M) 21.81 28.05 25.85Sd (effective radiating area, sq. cm.) 333.3 333.3 559.9Sd (effective radiating area, sq. m.) 0.03333 0.03333 0.05599Sd (effective radiating area, sq. in.) 51.6616 51.6616 86.78467Frequency range (Hz) 31-250 32-250 23-250Energy Bandwidth Product (EBP) 74 70 62Driver Physical DimensionSpeaker Displacement (cu ft.) 0.1268 0.15382 0.28931Mounting hole diameter (mm) 238 238 292Mounting hole diameter (inches) 9.37 9.37 11.496Mounting depth (mm) 214 214 261Mounting depth (inches) 8.425 8.425 10.276Magnet Weight (Oz) 263.7 263.7 445Basket diameter (inches)Recommended EnclosuresTypical sealed enclosure (cu. ft.) 0.5 to 0.8 0.5 to 0.8 0.9 to 1.35Vented enclosure (cu. ft.) 1.2 1.2 2Port tuning frequency (Hz) 38 38 38Port diameter (inside, in.) 3.4 3.4 5Equivalent square port (in.) 3x3 3x3 4.5x4.5Port length (in.) 12 12 15Enclosure Details1. Parameters listed are for conventional applications only, for further help please call Tech Audio Support2. 1" MDF is recommended.3. Recommended enclosures are NET Box Volumes, speaker and port displacement are calculated into thevolume of the enclosure, you will not need to add these volumes to calculate GROSS volume for theenclosure.*** Sub-sonic filters should always be used and adjusted specifically for vented box designs.NOTE: The woofer must face up or down only, especially in sealed enclosures.Specifications subject to change without notice© 2007 Directed Electronics, Inc. Vista, CA 92081 All rights reserved.

24

SPECIFICATIONS (CONT’D)

Directed Part Number 27309 27312 27314Model Number 12.4 15.2 15.4

Thiele/Small ParametersFs (free-air resonance, Hz) 23.98 23.72 24.73Vas (equivalent compliance, cu. ft. 1.847 4.01 7.23Vas (equivalent compliance, liters) 52.33 113.68 113.68Qms (Q, mechanical) 2.99 2.99 2.99Qes (Q, electrical) 0.42 0.46 0.52Qts (total driver Q) 0.37 0.40 0.44Re (DC resistance, ohms) 7.76 4.08 7.23Z (nominal impedance, ohms) 2 x 4 2 x 2 2 x 4Le (inductance, mh) 3.67 2.59 3.68Efficiency (1W @ 1M, dB) 85 88 88Xmax (one way linear excursion, in.) 1.2 1.2 1.2Xmax (one way linear excursion, mm) 30 30 30Pe (continuous power handling, watts) 2000 2000 2000Peak power handling (music, watts)** 4000 4000 4000Mms (total moving mass, grams) 372.77 517.86 476.42Cms (mechanical compliance, mm/N) 0.118 0.087 0.087Bl (motor strength, Tesla-M) 32.07 26.03 32.15Sd (effective radiating area, sq. cm.) 559.9 962.1 962.1Sd (effective radiating area, sq. m.) 0.05599 0.09621 0.09621Sd (effective radiating area, sq. in.) 86.78467 149.1258 149.1258Frequency range (Hz) 24-250 24-250 24-250Energy Bandwidth Product (EBP) 57 51 48Driver Physical DimensionSpeaker Displacement (cu ft.) 0.30361 0.37704 0.33403Mounting hole diameter (mm) 292 383 383Mounting hole diameter (inches) 11.496 15.079 15.079Mounting depth (mm) 261 294 294Mounting depth (inches) 10.276 11.575 11.575Magnet Weight (Oz) 445 445 445Basket diameter (inches)Recommended EnclosuresTypical sealed enclosure (cu. ft.) 0.9 to 1.35 1.9 to 2.5 1.9 to 2.5Vented enclosure (cu. ft.) 2 3.5 3.5Port tuning frequency (Hz) 35 35 35Port diameter (inside, in.) 5 6.25 6.25Equivalent square port (in.) 4.5x4.5 5.5x5.5 5.5x5.5Port length (in.) 15 14.5 14.5NOTE: Due to the high power capabilities and long excursion of these woofers, the Thiele/Small Parameterswere calculated and measured using a Klippel analyzer system.

25

NO WARRANTY

THIS PRODUCT IS SOLD "AS-IS"

DIRECTED ELECTRONICS (hereinafter "SELLER") MAKES NO WARRANTY of any kind(express, implied or otherwise) in connection with this Product. THIS PRODUCT IS SOLDAS-IS, AND YOU THE PURCHASER ASSUME THE ENTIRE RISK AS TO ITS QUALITY ANDPERFORMANCE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE THAT EXCEEDS THE FOREGOING WARRANTY IS HEREBYEXPRESSLY DISCLAIMED BY SELLER TO THE MAXIMUM EXTENT ALLOWED BY LAWAND IS EXCLUDED FROM ANY AGREEMENT MADE BY ACCEPTING THIS OFFER.SELLER neither assumes nor authorizes any person to assume for it any liability inconnection with the sale of this Product. SELLER has absolutely no liability for any and allacts of third parties including distributors, authorized dealers or installers. SELLER will notbe liable for any direct, indirect, special, incidental or consequential damages, loss orexpense arising in connection with the use of the Product or the inability to use the Productfor any purpose whatsoever. This Product is not eligible for return or exchange. Any returnof this Product to SELLER will be declined at Shipper's expense.

All exclusions and limitation are made only to the extent permitted by applicable law andshall be of no effect to the extent in conflict with the express requirements of applicablelaw. Some states do not allow the exclusion or limitation of incidental or consequentialdamages. In such states, the exclusion or limitations stated herein may not apply to you.You may have specific legal or other rights which vary from state to state.

p/n 920-0034 01-07

For more information on Orion products please visit us at www.orioncaraudio.com

© 2007 Directed Electronics, All rights reserved. G27302.04.07.09.12.14 03-07

Date post:	27-Apr-2018
Category:	Documents
Upload:	donhi
View:	218 times
Download:	3 times

subwoofer HCCA 10.2 10.4 12.2 12.4 15.2...

Documents