7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 1/12

Ama®-PorterType series booklet2539.56/3--10

Submersible motor pumps

60 Hz

Fields of ApplicationPumping of waste water containing solid matter or domesticsewage such as waste from toilets, washing machines,dishwashers, in intermittent operation, etc.

Surface water or rain water pumping in intermittent operationsuch as car park drainage.

Drainage of sumps liable to flooding.

Operating characteristicsQ : up to 40 m3 /h, (11 l/s).

H : up to 17 m.

Motor Power ;

1.5 kW maximum for three phase motor

1.1 kW maximum for single phase motor

Operating temperature up to 40ºC

Intermittently 70ºC (3 to 5 min.)

MaterialsCasing : EN.GJL--200 / JL 1030 / FGL 200 / GG 20.

Impeller : EN.GJL--200 / JL 1030 / FGL 200 / GG 20.

Shaft : Chrome steel 1.4021 / X20 Cr13 / Z20 C13.

Shaft seal : (Motor side) Lip sealShaft seal : (Pump side) Mechanical seal

Silicium Carbide/Alumin Oxide

Nuts & bolts : Stainless steel

Elastomers : Nitrile rubber

Float switch : Polypropylene

DesignVertical single casing submersible motor pump.

Shaft sealTwin shaft seal with intermediate oil chamber.

Motor side : Single lip seal

Pump side : Single mechanical seal independentof direction of rotation

Designation

Type of pump :

Discharge diameter

DN 50 = serie 5 -- --DN 65 = serie 6 -- --

Impeller size :

SE = Single--phase with float switchNE = Single--phase without float switchND = Three--phase without float switch

Ama --Porter 5 01 SE

MotorSingle phase : 220/255V -- 60 Hz with built in thermal

overload protection

Three phase : 380/460V -- 60 Hz direct on--line starting

Motor protection : IP68, Class F insulation in accordancewith EN 60529 / IEC 529

Please note :Variable--speed operation of this pump is not

allowed.

Operating mode S1 - submerged (max. 5 m)Operating mode S3 - not submerged

(see dimension table)

BearingsSealed for life radial ball bearings.

-- EN 12 050

The pump must not be used in countries where pumpshandling sewage with faeces are subject to explosionprotection regulations.

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 2/12

Ama®-Porter

Subject to modifications2

Scope of SupplyPump complete ready for installation with either stationary or

transportable mounting kits.

The SE versions are fitted with an integral float switch.

Details-- Manufactured in cast iron construction

EN.GJL--200 / JL 1030 / FGL 200 / GG 20.

-- Non--flameproof motor.

-- Unique resin imbedded, plug connection.

-- Single phase version are supplied with a 10 m electricalcable and plug.

-- Three phase version supplied with a 10 m electrical cable.

-- Integral cast handle for easy hanging or lifting.

-- Paint coating:

Surface treatment: SA 21 / 2, Sis 055900

Primer : Ferritic Oxide 35 to 40 μm

Top coat : environmentally--friendly KSB--standard coating,

approx.40 μm, RAL 5002 (ultramarine blue).

Description of installation kits

Series 5 _ _  SE/NE/ND 6 _ _  SE/NE/ND

Version

Transportable 3 feet in stainless steel

Discharge elbow (2”)

Hosetail (2”)

Hose clip (∅ 60 to 80)

Nuts and bolts for feet and elbow

3 feet in stainless steel

Discharge elbow (2”)

Hosetail (2”1 / 2)

Hose clip (∅ 80 to 100)

Nuts and bolts for feet and elbow

Stationary

Guide rope or rail (1 or 2) or hoop(vertical discharge connection)

Duckfoot bend 50/50 mm

ClawBracket

Guiding rope or hoop

1 or 2 Rail(s) not included

 Anchor bolts

Chain

Duckfoot bend 65/65 mm

ClawBracket

Guiding rope or hoop

1 or 2 Rail(s) not included

 Anchor bolts

Chain

Stationary

Guide rope or 1 rail or hoop

(horizontal discharge connection)

Duckfoot bend 50/2“

Claw

Bracket

Guiding rope or hoop

Rail not included

 Anchor bolts

Chain

Pump pedestal 65/2“1 / 2Claw

Bracket

Guiding rope or hoop

Rail not included

 Anchor bolts

Chain

Thermal overload protectionSingle phase versionIntegral thermal overload protection within motor windings.

Three phase versionNo thermal protection of the windings, current supply shouldbe protected via a thermal overload relay installed inside thecontrol panel and set to the current value indicated on therating plate +15%

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 3/12

Ama®-Porter

Subject to modifications 3

Advantages offered by the Ama®-Porter pump.

Resin impregnated cable connectionplug.

 Your benefit:Absolutely water tight cable entry.

Side cable entry position ensu-res the cable is protectedagainst damage.

 Your benefit:

Safe and easy transporthandling.

Chrome steel shaft.

 Your benefit:No corrosion, longlifetime.

Hard wearing mechani-cal seal independent of rotation direction.

 Your benefit:Long service life.

Freeflow vortex impeller.

 Your benefit:Casing with F impeller ensuringmaximum solids passage without

blockage.

Stainless steel nuts and bolts.

 Your benefit:Corrosion resistant to ensure easyremoval at times of maintenance.

Stationary version,automatic easyconnection to pipe-work without faste-ners. A flexiblegasket ensuresperfect tightness.

 Your benefit:

It is the simplestand quickest wayto install and ser-vice a pump in apit.

Three phase version,oversized motor ensuringgood operating condi-tions.

 Your benefit:

Maximum performanceeven under the mostarduous of duties.

Single phase version protected

against thermal overload by inte-gral winding protection.

 Your benefit:Motor is protected, even in auto-matic operation conditions.

Singular casing submersible motorwith Class F insulation designed

for optimum performance.

 Your benefit:Optimum motor design for safeoperating conditions.

Contactor and polarizingslot.

 Your benefit:Quick servicing, with-out risk of faulty con-nection

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 4/12

Ama®-Porter

Subject to modifications4

Ama®-Porter size 5 _ _ SE/NE/ND 3 500 1/min

LaufradformImpeller type

Forme de roueTipo girante

Tipo de rodete

freier Durchgangfree passage

section de passagepassaggio libero

paso libre

Kennlinien nach DIN1944/III. Sie entspre-chen der effektivenMotordrehzahl.

Curves as per DIN1944/III. They corres-pond to the effectivemotor speed.

Courbes selon DIN1944/III. Elles corres-pondent à la vitessede moteur effective.

Curve secondo DIN1944/III. Correspon-denti agli effettivi giridel motore.

Curvas según DIN1944/III. Se refieren ala velocidad efectivadel motor.Förderstrom/Capacity/Débit/Portate/Caudal

501 = 45 mm500 = 45 mm

FörderhöheHeadHauteurPrevalenza

 Alturamanométrica

500

501

m3 /h

60 Hz -- 1~ 220/255V Type Impeller

diameterP1 P2 IN ID Temp. Electric

cableOuter

diameterWeight Ident. Nr

mm kW kW (A) (A) t°C mm kg

500 SE [UK] 100 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 22 39 017 142501 SE [UK] 110 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 22 39 017 803

500 NE [UK] 100 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 22 39 017 699

501 NE [UK] 110 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 22 39 017 804

60 Hz -- 3~ 380/460V 500 ND 100 1.5 1.1 2.8 18.3 40 4 x 1 mm2 10 22 39 017 143

501 ND 110 1.9 1.5 3.5 18.3 40 4 x 1 mm2 10 22 39 017 144

The diagrams refer to the effective speed of the motor.Density=1, viscosity=1 cSt.

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 5/12

Ama®-Porter

Subject to modifications 5

Ama®-Porter size 6 _ _ SE/NE/ND 3 500 1/min

LaufradformImpeller type

Forme de roueTipo girante

Tipo de rodete

freier Durchgangfree passage

section de passagepassaggio libero

paso libre

Kennlinien nach DIN1944/III. Sie entspre-chen der effektivenMotordrehzahl.

Curves as per DIN1944/III. They corres-pond to the effectivemotor speed.

Courbes selon DIN1944/III. Elles corres-pondent à la vitesse

de moteur effective.

Curve secondo DIN1944/III. Correspon-denti agli effettivi giridel motore.

Curvas según DIN1944/III. Se refieren ala velocidad efectivadel motor.

Förderstrom/Capacity/Débit/Portate/Caudal

601 = 60 mm600 = 60 mm

FörderhöheHeadHauteurPrevalenza

 Alturamanométrica

601600

m3 /h

60 Hz -- 1~ 220/255V Type Impeller

diameterP1 P2 IN ID Temp Electric

cableOuter

diameterWeight Ident. Nr

mm kW kW (A) (A) t°

C mm kg600 SE [UK] 100 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 25 39 017 145

601 SE [UK] 110 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 25 39 017 805

600 NE [UK] 100 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 25 39 017 700

601 NE [UK] 110 1.9 1.1 8.2 18.2 40 3 x 1 mm2 9 25 39 017 806

60 Hz -- 3~ 380/460V 600 ND 100 1.5 1.1 2.8 18.3 40 4 x 1 mm2 10 25 39 017 146

601 ND 110 1.9 1.5 3.5 18.3 40 4 x 1 mm2 10 25 39 017 147

The diagrams refer to the effective speed of the motor.Density=1, viscosity=1 cSt.

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 6/12

Ama®-Porter

Subject to modifications6

Dimensions

Ama®-Porter size 5 _ _  Transportable version

(1) lowest switch off level

For flexible hoseinner diameterØ 63 mm

Ama®-Porter size 6 _ _  Transportable version

(1) lowest switch off level

For flexible hoseinner diameterØ 80 mm

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 7/12

Ama®-Porter

Subject to modifications 7

Dimensions

Ama®-Porter size 5 _ _ 

 Vertical flange discharge DN 50/50Stationary version with guide wire lifting system

Stationary version with guide hoop

ISO 7005 PN 16DN 50 PN 16

 ASME 2”

Flange of duckfootbend

(1) lowest switch off level

Guide hoop

     1     3     8

Ama®-Porter size 6 _ _ 

 Vertical flange discharge DN 65/65Stationary version with guide wire lifting systemStationary version with guide hoop

ISO 7005 PN 16DN 65 PN 16 ASME 2”1 / 2

Flange of duckfootbend(1) lowest switch off level

Guide hoop

     1     8     3

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 8/12

Ama®-Porter

Subject to modifications8

Dimensions

Ama®-Porter size 5 _ _ 

 Vertical flange discharge DN 50/50Stationary version with guide rail lifting system

1 Rail

ISO 7005 PN 16DN 50 PN 16

 ASME 2”

(1) lowest switch off level

Flange of duckfootbend

     1     3     8

Pipe Ø 33.7 x 3.2

     1     8     3

Ama®-Porter size 6 _ _ 

 Vertical flange discharge DN 65/65Stationary version with guide rail lifting system1 Rail

ISO 7005 PN 16DN 65 PN 16 ASME 2”1 / 2

Flange of duckfootbend

Pipe Ø 33.7 x 3.2

(1) lowest switch off level

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 9/12

Ama®-Porter

Subject to modifications 9

Dimensions

Pipe Ø 33.7 x 3.2

Ama®-Porter size 5 _ _ 

 Vertical flange discharge DN 50/50Stationary version with guide rail lifting system -- 2 Rails

(1) lowest switch off level Flange of duckfoot bend

(1) lowest switch off level

Ama®-Porter size 6 _ _ 

 Vertical flange discharge DN 65/65Stationary version with guide rail lifting system -- 2 Rails

Pipe Ø 33.7 x 3.2

Flange of duckfoot bend

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 10/12

Ama®-Porter

Subject to modifications10

Dimensions

Ama®-Porter size 5 _ _ 

Horizontal pedestal installation G 2”Stationary version with guide wire lifting system

Stationary version with guide hoop

(1) lowest switch off level

Guide hoop

     1     3     8

Ama®-Porter size 6 _ _ 

Horizontal pedestal installation G 2” 1 / 2Stationary version with guide wire lifting systemStationary version with guide hoop

Guide hoop

(1) lowest switch off level

     1     8     3

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 11/12

Ama®-Porter

Subject to modifications 11

Dimensions

     1     3     8

Ama®-Porter size 5 _ _ 

Horizontal pedestal installation G 2”Stationary version with guide rail lifting system

1 Rail

Pipe Ø 33.7 x 3.2

(1) lowest switch off level

Ama®-Porter size 6 _ _ 

Horizontal pedestal installation G 2” 1 / 2Stationary version with guide rail lifting system1 Rail

(1) lowest switch off level

     1     8     3

Pipe Ø 33.7 x 3.2

7/27/2019 Technical Specifications for Centrifugal Pumps.pdf

http://slidepdf.com/reader/full/technical-specifications-for-centrifugal-pumpspdf 12/12

     0     9     /     2     0     0     8

     2     5     3     9 .     5

     6     /     3  -  -     1     0

     S    u     b     j    e    c     t     t    o     t    e    c     h    n     i    c    a     l    m    o     d     i     f     i    c    a     t     i    o    n    s .

Ama®-Porter

On

Off 

Installation in a sump

    m     i    n     i

Dimensions in mm

A B C D

Ama--Porter 5 _ _  600 x 600 160 190 450

Ama--Porter 6 _ _  600 x 600 170 190 480

KSB S.A.128, rue Carnot -- 59320 Sequedin (Lille)B.P. 60095 -- 59482 Haubourdin Cedex -- France

D Phone : +33 3 20 22 70 00D Fax : +33 3 20 22 71 47 D http:/www.ksb.com