The Centre of Excellence for sheet - emw-stahlservice.de · The Centre of Excellence for sheet –...

1

The Centre of Excellence for sheet – Grade variety keeps us ahead

www.emw-stahlservice.com

2

I. Company

3

A tradition of top performanceSince EMW was founded in 1952, each and every employee

has passionately worked towards achieving our goal of

providing our customers with intelligent, high-quality and

individually tailored steel service solutions. The focus is on

your requirements at all times. For us, competent and

ambitious customer care is so much more than simply

going about our daily business. It’s our passion.

High efficiency to match your expectationAs one of the industry’s largest steel service centres, EMW

is a supplier of coils, slit strips, cut-to-size sheets and circular

blanks. Our highly efficient machines, consisting of modern

slitting lines, longitudinal and lateral slitting lines and

cutting centres guarantee fast and flexible deliveries. Our

market-oriented product range is therefore supplemented

by the highest possible level of customer-oriented service,

ranging from competent advice and quality control right

up to logistics.

I. Company 2

II. Product range 4

III. Consulting 6

IV. Quality 8

V. Service 10

VI. Perforated metal 12

VII. Hot-rolled sheet 15

VIII. Cold-rolled sheet 20

IX. Electrolytically galvanized sheet 23

X. Hot-dip galvanized sheet 27

XI. Hot stamping steels (22MnB5) 30

XII. Designation system for steels acc. to EN 10027 30

XIII. The SCHÄFER WERKE Group of Companies 32

XIV. Contact 34

Steel Service – that’s our missionSheet from EMW.

Your benefitsn Extensive product range offers greatest possible choicen Intelligent and bespoke solutions for your projectsn Competent and reliable customer support, even at your premises Competent

consultingGreat

variety

4

II. Product range

5

CoilsEMW has over 100,000 t of input material in stock in an

area measuring 32,000 m2. Almost all standard market

grades are constantly available for delivery; mainly hot-dip

and electrolytically galvanized, warm and cold-rolled

and hot-dip aluminised. High-quality automobile grades,

high-tensile steels and grades for enamelling are particular

EMW specialities. All are available in widths of up to 1,850

mm, thicknesses up to 4.50 mm and coil weights of up

to 32 t. This extensive assortment and the vast storage

capacity are benefits our customers profit from.

Slit stripsAs a matter of tradition, EMW operations are based on

advanced production technology and the highest

quality standards. Slit strips and trimmed wide strips in

various finishes are produced on state-of-the-art facilities.

The finest tolerances, cleanly cut edges and extremely

smooth surfaces characterise all our products.

The strips are loaded according to your specifications;

flat or upright for subsequent handling by crane or

fork-lift truck. Here too, EMW shows its unbeatable

flexibility.

Cut-to-size blanks/sheetsCut-to size blanks and sheets are among our core com-

petencies, with a delivery range covering thicknesses from

0.40 mm, widths of up to 1,850 mm and lengths up to

6,000 mm. Advanced cutting centres cut blanks of various

surface finishes from coils or sheets with precision and

reliability. CNC controlled facilities guarantee maximum

efficiency and accuracy. We can supply any dimension

in the specified grades in the shortest possible delivery

time.

Apart from the usual stock sizes, we also have a great

number of different ready-made blanks ranging from

0.40 - 3.00 mm in thickness, and in all grades.

Alternatively, EMW can tell you the coil widths available

and you can specify the sheet lengths.

Hot-rolled n n n

Cold-rolled n n n

Electrolytically galvanized n n n

Hot-dip galvanized n n n

Hot-dip aluminised n n n

Steel – our portfoliois your benefit

Sheet from EMW.

High efficiency

Highestquality

Your benefitsn Over 100,000 t of material ready for delivery – just call usn The most advanced technologies – top results for youn Highest quality standards, no compromises

6

III. Consulting

7

A partner you can rely onEMW attaches great importance to reliable consulting

and advice provided by a permanent personal contact,

who will deal intensively with your needs right from

the outset. It is our strong belief that long term

partnerships can only develop if we make your projects

our projects.

Experience makes all the differenceOur long standing experience in steel purchasing,

combined with our extensive storage capacity of around

32,000 m2 means we can take advantage of spot market

opportunities worldwide. This enables us to provide you

with high-grade material at competitive market prices.

A further benefit is that you can reduce your storage costs

by using EMW as your “upstream warehouse”.

Sheet from EMW.

Large storage capacity

Reliable personal contacts

Your benefitsn A permanent and reliable personal contactn Large storage capacity enables reliable planningn Our experience in steel purchasing guarantees top conditions for you

Steel – our expertise is added value for your product

8

IV. Qualität

9

Steel – the highest qualityfor problem-free processing

Sheet from EMW.

Environment management

Own testing laboratory

Your benefitsn Our own testing laboratory for continuous controln Certified quality management to meet the highest demandsn Environment management system certified to ISO 14001

EMW’s entire organisation is characterised by its com-

plete orientation to the customers, their needs and

expectations. A continuous, documented quality

assurance system and the best possible service is an

indispensable part of this.

Your demands are what spurs us onThe consistent quality of the input material alone is the

key to the trouble-free processing of our products by

our customers. For this reason, EMW has its own testing

laboratory. Here both, the material and processing

quality are continuously examined and documented.

To ensure we can meet our customers‘ increased

demands regarding quality, we have had our quality

management certified according to TS 16949. And on

top of that, EMW also has the ISO 14001 Environmental

Management Certificate.

Our flexibility opens up possibilities for youWhen it comes to storage capacity, speed and flexibility,

EMW is totally reliable. You specify material, quantity and

date, and we take care of the rest. For our experienced

team, professional supply chain management and just-

in-time delivery are all in a day‘s work. The extensive

range of grades available enables us to react quickly to

tight delivery deadlines and requests for alterations.

10

V. Service

11

To offer our customers the best possible service, we put

all our energy into working on innovative solutions to

make your work easier.

Optimum materials flow guarantees reliable deliveryIn order processing in particular, EMW is expanding

digital information exchange. This means you can

receive order confirmations, stock levels, delivery notes,

test results, invoices etc. by e-mail or EDI (Electronic

Data Interchange) and constantly monitor the current

status of your order.

We use our enormous storage capacity to ensure we

have a wide ranging, permanently available grade

variety. Our highly efficient machines, consisting of

modern slitting lines, longitudinal and lateral slitting

lines and cutting centres guarantee optimal materials

flow and further processing at short notice.

Thanks to professional supply chain management, we

can also guarantee just-in-time delivery for large quanti-

ties very quickly and will be happy to offer advice on

which solutions would be most efficient for you.

Calculating coil data has never been so easy – on your Smartphone!With the new coil and steel calculator, you can enter a

few simple details and work out all necessary data,

such as weight, external diameter, coil length, kg/mm of

coil width and winding height. You can also calculate

sheet and package weights or the number of pallets

needed for shipping. The calculations can of course be

saved and retrieved in the App at any time,

a very practical function.

Steel – digital service andjust-in-time delivery

Sheets from EMW.

Just-in-time delivery

Digital services

Your benefitsn Digital services for convenient information exchangen Just-in-time deliver for large quantitiesn Professional supply chain management for short-notice deliveries

12

V. Perforated Metal

13

Perforated metal made to measure – individual and fast

SCHÄFER Perforated Metal.

The application potential of perforated metal is unlimited

and no doubt a major factor in the unbroken success this

material has experienced over recent decades.

Perforated Metal from SCHÄFER meets the highest

standards of quality.

Perforated metal from SCHÄFER. Precision in Steel.Perforated metal – when it comes to combing countless

different demands of function and design in such a

fascinating way, there’s no other material quite like it.

Perforated metal can now be found in almost all walks

of everyday life. The possibilities are boundless and they

are growing day by day. And so are the demands the

processing industries are placing on this fashionable

material. The name “SCHÄFER Perforated Metal” has

been syno-nymous with professionalism, perfection

and precision for many years. Storage capacity, service

range and delivery service are second to none. The

experts from Neunkirchen set standards in market and

customer orientation and show precisely what is meant

by ex-pertise in this field through the wide range of

different services on offer. The customer specifies the

material, the perforation pattern and the dimensions –

SCHÄFER does the rest: coil-to-coil perforation, sheets

or cut-to-size sheets to precise customer specifications,

extensive stocks covering many standard formats,

materials and perforation patterns.

Apart from our speedy delivery service, the fact that

we offer a full range processing service also makes us a

greatly appreciated business partner: whether punching,

laser cutting, notching, bending, welding, degreasing,

powder coating or galvanising – on request SCHÄFER

can take on the precise processing of the material you

order.

Perforated metal, Sales

Business Unit Sales DirectorAlexander Toumassian Tel. +49 (0) 2735/[email protected]

Vertriebsassistenz: Daniela KämpkenTel. +49 (0) 2735/787-624PC-Fax +49 (0) 2735/[email protected]

Sekretariat: Julia Brockhaus Tel. +49 (0) 2735/787-449PC-Fax +49 (0) 2735/[email protected]

Sales area

PLZ 0, 1, 2, 30-31, 37-39, 98, 99Adrian Lück Tel. +49 (0) 2735/[email protected]

PLZ 32-34, 4, 50-53, 58, 59Rolf Werle Tel. +49 (0) 2735/[email protected]

PLZ 35-36, 54-57, 80-87, 90-97 Patrick Diehl Tel. +49 (0) 2735/[email protected]

PLZ 6, 7, 88, 89Oliver Porr Tel. +49 (0) 2735/[email protected]

BeNeLux Rüdiger Boller Tel. +49 (0) 2735/[email protected]

BeNeLux/A/CH/FR/PL/Scandinavia Eric Diehl Tel. +49 (0) 2735/787-394 [email protected]

Czech Republic/Slowakia Adrian Lück Tel. +49 (0) 2735/787-325 [email protected]

Sales agencies, international

Austria Intermold Industrieservice GmbHHelmut MalznerRosenweg 1 · A-4542 NußbachTel. +43 7587/6011 · Fax +43 7587/[email protected]

SwitzerlandTECmetallRobert Blarer IndustrievertretungenBrunnenweg 2a · CH-5436 WürenlosTel. +41 44 400 12 80 · Fax +41 44 400 12 [email protected]

Czech Republic Dipl.-Ing. Miroslav KotrčDružstevní 323 · CZ-37810 České VeleniceTel. +420 [email protected]

Technical salesMachining/ProjectsThomas NassenTel. +49 (0) 2735/[email protected]

Torsten Schoew Tel. +49 (0) 2735/787-433 PC-Fax +49 (0) 2735/787-1-433 [email protected]

Contract manufacturingRüdiger BollerTel. +49 (0) 2735/[email protected]

14

15

Dicken ab 1,00 – 4,00 mm ab 1,00 – 4,50 mm ab 1,00 – 3,00 mm

Breiten bis 1.850 mm bis 1.850 mm bis 1.530 mm bis 1.850 mm

Längen --- --- bis 8.000 mm bis 3.000 mm

Toleranzen Toleranzen für Bänder und Bleche: DIN EN 10051. Engere Toleranzen und besondere Kantenausbildung nach Absprache

Lieferprogramm der EMW Coils Spaltband Formate / Zuschnitte

Mild grades – continuously hot-rolled strip and sheet of mild steels for cold forming acc. to DIN EN 10111 : 2008Steel grade/type Chemical composition Mechanical properties (lat.) (Melt analysis) ReL

1) Rm Min. fracture elongation

LO = 80 mm LO = 5.65 √SO

C Mn P S 1.0 mm ≤ e 2.0 mm ≤ e 1.0 mm ≤ e 1.5 mm ≤ e 2.0 mm ≤ e 3.0 mm ≤ e e < 2.0 mm e < 4.5 mm max. e < 1.5 mm e < 2.0 mm e < 3.0 mm e < 4.5 mm Code VDA Material no. max. % max. % max. % max. % N/mm2 N/mm2 N/mm2 % % % % 239-100 DD11 1.0332 0.12 0.60 0.045 0.045 170 – 360 170 – 340 440 22 23 24 28 DD12 1.0398 0.10 0.45 0.035 0.035 170 – 340 170 – 320 420 24 25 26 30 DD13 1.0335 0.08 0.40 0.030 0.030 170 – 330 170 – 310 400 27 28 29 33 DD14 HR2 1.0389 0.08 0.35 0.025 0.025 170 – 310 170 – 290 380 30 31 32 36

1) If the product has no pronounced yield point, Rp0,2 must be used instead of ReL.

Thicknesses from 1.00 – 4.50 mm from 1.00 – 4.50 mm from 1.00 – 3.00 mmWidths up to 1,850 mm up to 1,850 mm up to 1,530 mm up to 1,850 mm Lengths --- --- up to 6,000 mm up to 3,000 mmTolerances Tolerances for strips and sheets: DIN EN 10051. Finer tolerances and special edge formation available by arrangement.

EMW delivery range Coils Slit strip Cut-to-size sheet

Microalloyed grades – hot-rolled flat products of steels with high yield point for cold forming acc. to DIN EN 10149 : 2013Mechanical properties of thermo-mechanically rolled steels (long.) Steel grade/type Upper yield point Tensile strength Fracture elongation, A1)

ReH1)

Rm1)

% min. N/mm2 min N/mm2 nominal thickness in mm < 3 ≥ 3 Code VDA 239-100 Material no. LO = 80 mm LO = 5,65 √SO

S315MC HR 300 MC 1.0972 315 390 – 510 20 24 S355MC HR 340 MC 1.0976 355 430 – 550 19 23 S420MC HR 420 MC 1.0980 420 480 – 620 16 19 S460MC HR 460 MC 1.0982 460 520 – 670 14 17 S500MC HR 500 MC 1.0984 500 550 – 700 12 14 S550MC 1.0986 550 600 – 760 12 14 S600MC 1.8969 600 650 – 820 11 13 S650MC 1.8976 650

3) 700 – 880 10 12

S700MC 1.8974 7003)

750 – 950 10 12 S900MC 1.8798 900 930 – 1200 7 8 S960MC 1.8799 960 980 – 1250 6 7

Chemical composition (melt analysis) of thermo-mechanically rolled steels Steel grade/type C Mn Si P S Altotal Nb V Ti Mo B % % % % % % % % % % % Code VDA 239-100 Material no. max. max. max. max. max.

min. max.

max. max. max. max.

S315MC HR 300 MC 1.0972 0,12 1,30 0,50 0,025 0,020 0,015 0,09 2)

0,20 2)

0,15 2)

– – S355MC HR 340 MC 1.0976 0,12 1,50 0,50 0,025 0,020 0,015 0,09

2) 0,20

2) 0,15

2) – –

S420MC HR 420 MC 1.0980 0,12 1,60 0,50 0,025 0,015 0,015 0,09 2)

0,20 2)

0,15 2)

– – S460MC HR 460 MC 1.0982 0,12 1,60 0,50 0,025 0,015 0,015 0,09

2) 0,20

2) 0,15

2) – –

S500MC HR 500 MC 1.0984 0,12 1,70 0,50 0,025 0,015 0,015 0,09 2)

0,20 2)

0,15 2)

– – S550MC 1.0986 0,12 1,80 0,50 0,025 0,015 0,015 0,09

2) 0,20

2) 0,15

2) – –

S600MC 1.8969 0,12 1,90 0,50 0,025 0,015 0,015 0,09 2)

0,20 2)

0,22 2)

0,50 0,005 S650MC 1.8976 0,12 2,00 0,60 0,025 0,015 0,015 0,09

2) 0,20

2) 0,22

2) 0,50 0,005

S700MC 1.8974 0,12 2,10 0,60 0,025 0,015 0,015 0,09 2)

0,20 2)

0,22 2)

0,50 0,005 S900MC 1.8798 0,20 2,20 0,60 0,025 0,010 0,015 0,09

2) 0,20

2) 0,25 1,00 0,005

S960MC 1.8799 0,20 2,20 0,60 0,025 0,010 0,015 0,09 2)

0,20 2)

0,25 1,00 0,005

1) The values for the tensile test are those determined for longitudinal samples.2) The sum of Nb, V and Ti must not exceed 0.22 %.3) For thicknesses > 8 mm, the yield point values may be 20 N/mm2 lower.

VII. Hot-rolled sheet

16


Dicken ab 1,00 – 4,00 mm ab 1,00 – 4,50 mm ab 1,00 – 3,00 mm

Breiten bis 1.850 mm bis 1.850 mm bis 1.530 mm bis 1.850 mm

Längen --- --- bis 8.000 mm bis 3.000 mm

Toleranzen Toleranzen für Bänder und Bleche: DIN EN 10051. Engere Toleranzen und besondere Kantenausbildung nach Absprache

Lieferprogramm der EMW Coils Spaltband Formate / Zuschnitte

Thicknesses from 1.00 – 4,50 mm from 1.00 – 4.50 mm from 1.00 – 3.00 mmWidths up to 1,850 mm up to 1,850 mm up to 1,530 mm up to 1,850 mm Lengths --- --- up to 6,000 mm up to 3,000 mmTolerances Tolerances for strips and sheets: DIN EN 10051. Finer tolerances and special edge formation available by arrangement.


Construction steels – hot-rolled products of unalloyed construction steels with values for notch impact strength acc. to DIN EN 10025 : 2005 Mechanical properties Steel grade/type Minimum yield Tensile strength Rm

1) Min. fracture elongation1)

point Reh 1) N/mm2 Sample

1) LO = 80 mm LO = 5.65 √SO

N/mm2 nominal thickness mm nominal thickness mm nominal nominal thickness mm thickness mm > 1 > 1,0 > 1,5 > 2,0 ≥ 2,5 ≥ 3 Code Material no.

≤ 4

< 3 ≥ 3 – ≤ 4 ≤ 1 ≤ 1,5 ≤ 2 ≤ 2,5 < 3 ≤ 4

S235JR 1.0038 235 360 – 510 360 – 510 l 17 18 19 20 21 26 S235J0 1.0114 235 360 – 510 360 – 510 S235J2 1.0117 235 360 – 510 360 – 510 t 15 16 17 18 19 24 S275JR 1.0044 275 430 – 580 410 – 560 l 15 16 17 18 19 23 S275J0 1.0143 275 430 – 580 410 – 560 S275J2 1.0145 275 430 – 580 410 – 560 t 13 14 15 16 17 21 S355JR 1.0045 355 510 – 680 470 – 630 l 14 15 16 17 18 22 S355J0 1.0553 355 510 – 680 470 – 630 S355J2 1.0577 355 510 – 680 470 – 630 S355K2 1.0596 355 510 – 680 470 – 630 t 12 13 14 15 16 20 S450J0 1.0590 450 – 550 – 720 l – – – – – 17

Chemical composition after melt analysis for flat and long products made of steel types with values for notch impact strength Steel grade/type C Si Mn P S N Cu max. % max. % max. % max. % max. % max. % max. % Code Material no. S235JR 1.0038 0.17 – 1.40 0.035 0.035 0.012 0.55 S235J0 1.0114 0.17 – 1.40 0.030 0.030 0.012 0.55 S235J2 1.0117 0.17 – 1.40 0.025 0.025 – 0.55 S275JR 1.0044 0.21 – 1.50 0.035 0.035 0.012 0.55 S275J0 1.0143 0.18 – 1.50 0.030 0.030 0.012 0.55 S275J2 1.0145 0.18 – 1.50 0.025 0.025 – 0.55 S355JR 1.0045 0.24 0.55 1.60 0.035 0.035 0.012 0.55 S355J0 1.0553 0.20 0.55 1.60 0.030 0.030 0.012 0.55 S355J2 1.0577 0.20 0.55 1.60 0.025 0.025 – 0.55 S355K2 1.0596 0.20 0.55 1.60 0.025 0.025 – 0.55 S450J0 1.0590 0.20 0.55 1.70 0.030 0.030 0.025 0.55

1) For sheet, strip and wide flats in widths < 600 mm, the direction lateral (t) means transverse to roller direction. For all other products, the values are for roller direction (I).

17


Mechanical properties Steel grade/type Elongation limit Tensile strength Fracture elongation Fracture elongation Rpo.2 N/mm2 min Rm N/mm2 min A80 % min A5 % min Code VDA 239-100 Material no.

< 3 mm > 3 mm

FB-steel HDT450F HR300Y450T-FB 1.0961 300 – 420 450 24 27 HDT580F HR440Y580T-FB 1.0994 460 – 620 580 15 17 DP-steel HDT580X HR330Y580T-DP 1.0936 330 – 450 580 19 23 MS-steel HDT1180G1 HR900Y1180T-MS 1.0960 900 – 1.200 1.180 4 5 C-Stähle HDT760C HR660Y760T-CP 1.0998 660 – 830 760 10 12

Multiphase steels – hot-rolled products made of multiphase steels for cold forming acc. to prEN 10336 : 2015

Chemical properties Steel grade/type Percentage by mass % C Si Mn P S

Altotal

Cr + Mo Nb + Ti V B Code VDA 239-100 Material no. max. max. max. max. max. max. max. max. max. FB-steel HDT450F HR300Y450T-FB 1.0961 0,18 0,50 2 0,050 0,010 0,015 – 2,0 1,00 0,15 0,15 0,005 HDT580F HR440Y580T-FB 1.0994 0,18 0,50 2 0,050 0,010 0,015 – 2,0 1,00 0,15 0,15 0,010 DP-steel HDT580X HR330Y580T-DP 1.0936 0.14 1.00 2.20 0.085 0.015 0.015 – 0.1 1.40 0.15 0.20 0.005 MS-steel HDT1180M HR900Y1180T-MS 1.0960 0,25 0,80 2,50 0,060 0,015 0,015 – 2,0 1,20 0,25 0,22 0,005 C-Stähle HDT760C HR660Y760T-CP 1.0998 0,18 1,00 2,50 0,080 0,015 0,015 – 2,0 1,00 0,25 0,20 0,005

Thicknesses from 1.00 – 4.50 mm from 1.00 – 4.50 mm from 1.00 – 3.00 mmWidths up to 1,850 mm up to 1,850 mm up to 1,530 mm up to 1,850 mm Lengths --- --- up to 6,000 mm up to 3,000 mmTolerances Tolerances for strips and sheets: DIN EN 10051. Finer tolerances and special edge formation available by arrangement.


Construction steels – hot-rolled products of unalloyed construction steels without values for notch impact strength acc. to DIN EN 10025 : 2005

1) For sheet, strip and wide flats in widths > 600 mm, the direction lateral (t) means transverse to roller direction. For all other products, the values are for roller direction (I).

Mechanical properties Steel grade/type Minimum Tensile strength Rm

1) Min. fracture elongation1)

yield Sample LO = 80 mm LO

point Reh 1) position

1) = 5.65 √SO

Nominal Nominal thickness Nominal thickness thickness mm mm mm

Code

Material no. ≤ 4.5

< 3 ≥ 3 - ≤ 4.5

≤ 1 > 1 > 1.5 > 2 > 2.5 ≥ 3 P S N

N/mm2 N/mm2 N/mm2 ≤ 1.5 ≤ 2 ≤ 2.5 < 3 ≤ 4.5 % max. % max. % max.

S 185 1.0035 185 310 – 540 290 – 510 l 10 11 12 13 14 18

– – –

t 8 9 10 11 12 16

E 295 1.0050 295 490 – 660 470 – 610 l 12 13 14 15 16 20

0.045 0.045 0.012

t 10 11 12 13 14 18

E 335 1.0060 335 590 – 770 570 – 710 l 8 9 10 11 12 16

0.045 0.045 0.012

t 6 7 8 9 10 14

E 360 1.0070 360 690 – 900 670 – 830 l 4 5 6 7 8 11

0.045 0.045 0.012

t 3 4 5 6 7 10

18

VIII. Cold-rolled sheet


Thicknesses from 0.40 – 3.00 mm from 0.40 – 3.00 mm from 0.40 – 3.00 mm Widths up to 1,850 mm up to 1,850 mm up to 1,530 mm up to 1,850 mm Lengths --- --- up to 6,000 mm up to 3,000 mm Tolerances Acc. to DIN EN 10131; finer tolerances available by arrangement.

Mechanical properties (lat.) Steel grade/type Re

1) Rm A80 2) r90

3) 4) n90 3) Chemical composition

(Melt analysis) C P S Mn Ti Code VDA 239-100 Material no. N/mm2 N/mm2 min. % min. min. max. % max. % max. % max. % max. % DC01 CR1 1.0330 -/280 270 – 410 28 – – 0.12 0.045 0.045 0.60 – DC03 CR2 1.0347 -/240 270 – 370 34 1.3 – 0.10 0.035 0.035 0.45 – DC04 CR3 1.0338 -/210 270 – 350 38 1.6 0.180 0.08 0.030 0.030 0.40 – DC05 CR4 1.0312 -/180 270 – 330 40 1.9 0.200 0.06 0.025 0.025 0.35 – DC06 CR5 1.0873 -/170 270 – 330 41 2.1 0.220 0.02 0.020 0.020 0.25 0.3 DC07 1.0898 -/150 250 – 310 44 2.5 0.230 0.01 0.020 0.020 0.20 0.2

Mild grades – cold-rolled flat products of mild steels for cold forming DIN EN 10130 : 2007

1) For products with no clear yield point, the values for the 0.2 % elongation limit (Rp0,2), are taken as those for the yield point. For other products, those for the lower yield point (ReL) apply. For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a 20 MPa higher maximum yield point value is permissible. For thicknesses ≤ 0.50 mm, a higher maximum yield point value of 40 MPa is permissible.2) For thicknesses of ≤ 0.70 mm, but > 0.50 mm, the minimum values for fracture elongation are reduced by 2 units, for thicknesses of ≤ 0.50 mm by 4 units.3) The r90- and n90-values only apply for product thicknesses of > 0.50 mm.4) For thickness > 2 mm, the r90-value is reduced by 0.2.

Mechanical properties (lat.) Steel grade/type Re Rm A80

2) r 3) Chemical composition

(Melt analysis) N/mm2 1) N/mm2 min. min. C Ti Mn P S

Code Material no. max. DC01EK 1.0390 270 270 – 390 30 – 0.08 – 0.60 0.045 0.050 DC04EK 1.0392 220 6) 270 – 350 36 – 0.08 – 0.50 0.030 0.050 DC05EK 1.0386 220 270 – 350 36 1.5 0.08 – 0.50 0.025 0.050 DC06EK 1.0869 190 270 – 350 38 1.6 0.02 0.30 0.50 0.020 0.050 DC03ED 1.0399 240 270 – 370 34 – 5) – 0.40 0.035 0.050 DC04ED 1.0394 210 4) 270 - 350 38 – 5) – 0.40 0.030 0.050 DC06ED 1.0872 190 270 – 350 38 1.6 0.02 0.30 0.35 0.020 0.050

Enamelling grades – rolled flat products of mild steels for enamelling acc. to DIN EN 10209 : 2013

1) If the yield point is not pronounced, the values apply for the 0.2 % elongation limit (Rp0,2), if pronounced, the values apply to the lower yield point (ReL) apply. For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a minimum value for fracture elongation of 2 units lower is permissible, and of 4 units lower for thicknesses ≤ 0.50 mm.2) For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a minimum value for fracture elongation of 2 units lower is permissible, and of 4 units lower for thicknesses ≤ 0.50 mm.3) The r-values only apply for product thicknesses > 0.50 mm. For thicknesses > 2 mm, the r-value is reduced by 0.2.4) For thicknesses > 0.50 mm, the yield point may only reach a maximum of 225 N/mm2.5) The steel grades DC03ED and DC04ED are usually decarburized in the solid phase. After decarburization, analysis must only show a maximum carbon content of 0.004 %.6) If specified by the customer, steel grade DC04EK can be supplied in thicknesses of 0.7 mm to 1.5 mm with Re < 210 N/mm2 and A80 ≥ 38 %. It then remains for the manufacturer to select the surface roughness values for a dull matt finish.

19



Mechanical properties (lat.) Steel grade/type 0,2 % Higher yield Tensile strength Fracture Vertical Vertical Work hardening Elongation limit 1) point through elongation 3) anisotropy anisotropy 2) 3) 4) exponent 4) heat treatment 2) Rp0,2

1) BH2 Rm A80 r r n Code VDA 239-100 Material no. N/mm2 N/mm2 N/mm2 min. lat. % max. lat. min. lat. min lat. HC180Y CR180IF 1.0922 180 – 230 330 – 400 35 1,7 0.19 HC180B CR180BH 1.0395 180 – 230 35 290 – 360 34 1,6 0.17 HC220Y CR210IF 1.0925 220 – 270 340 – 420 33 1,6 0.18 HC220I 1.0346 220 – 270 300 – 380 34 1.4 0.18 HC220B CR210BH 1.0396 220 – 270 35 320 – 400 32 1,5 0.16 HC260Y CR240IF 1.0928 260 – 320 380 – 440 31 1,4 0.17 HC260I 1.0349 260 – 310 320 – 400 32 1.4 0.17 HC260B CR240BH 1.0400 260 – 320 35 360 – 440 29 HC260LA CR240LA 1.0480 260 – 330 350 – 430 26 HC300I 1.0447 300 – 350 340 – 440 30 1.4 0.16 HC300B 1.0444 300 – 360 35 390 – 480 26 HC300LA CR270LA 1.0489 300 – 380 380 – 480 23 HC340LA CR300LA 1.0548 340 – 420 410 – 510 21 HC380LA CR340LA 1.0550 380 – 480 440 – 580 19 HC420LA CR380LA 1.0556 420 – 520 470 – 600 17 HC460LA 1.0574 460 – 580 510 – 660 13 HC500LA 1.0573 500 – 620 550 – 710 12

Microalloyed grades – cold-rolled flat products with high yield point for cold forming made of microalloyed steels DIN EN 10268 : 2013

1) If a yield point is pronounced, the values for the lower yield (ReL) apply.2) For thicknesses > 1.2 mm, special arrangements must be made.3) For thicknesses ≤ 0.7 mm, but > 0.5 mm, minimum values for breaking elongation of two units lower are permissible. For thicknesses ≤ 0.5 mm, minimum values up to four units lower are permissible.4) The minimum values for r (lat.) and n (lat.) only apply to product thicknesses > 0.5 mm.5) For product thicknesses > 2 mm, the r90-value is reduced by 0.2.

Chemical composition after melt analysis Steel grade/type C Si Mn P S Al Ti Nb Code VDA 239-100 Material no. max. % max. % max. % max. % max. % min. % max. % max. % HC180Y CR180IF 1.0922 0.01 0.3 0.7 0.06 0.025 0.01 0.12 0,09 HC180B CR180BH 1.0395 0.06 0.5 0.7 0.06 0.030 0.015 HC220Y CR210IF 1.0925 0.01 0.3 0.9 0.08 0.025 0.01 0.12 0,09 HC220I 1.0346 0.07 0.5 0.6 0.05 0.025 0.015 0.05 HC220B CR210BH 1.0396 0.08 0.5 0.7 0.085 0.030 0.015 HC260Y CR240IF 1.0928 0.01 0.3 1.6 0.1 0.025 0.01 0.12 0,09 HC260I 1.0349 0.07 0.5 1.2 0.05 0.025 0.015 0.05 HC260B CR240BH 1.0400 0.1 0.5 1.0 0.1 0.030 0.015 HC260LA CR240LA 1.0480 0.1 0.5 1.0 0.030 0.025 0.015 0.15 0,09 HC300I 1.0447 0.08 0.5 0.7 0.08 0.025 0.015 0,05 HC300B 1.0444 0.1 0.5 1.0 0.12 0.030 0.015 HC300LA CR270LA 1.0489 0.12 0.5 1.4 0.030 0.025 0.015 0,15 0,09 HC340LA CR300LA 1.0548 0.12 0.5 1.5 0.030 0.025 0.015 0,15 0,09 HC380LA CR340LA 1.0550 0.12 0.5 1.6 0.030 0.025 0.015 0,15 0,09 HC420LA CR380LA 1.0556 0.14 0.5 1.6 0.030 0.025 0.015 0,15 0,09 HC460LA 1.0574 0.14 0.6 1.8 0.030 0.025 0.015 0,15 0,009 HC500LA 1.0573 0.14 0.6 1.8 0.030 0.025 0.015 0,15 0,009


20


Multiphase steels – cold-rolled products made of multiphase steels for cold forming prEN 10338 : 2007 (draft)

Chemical composition (Melt analysis) Steel grade/type Percentage by mass % C Si Mn P S

Altotal

Cr + Mo Nb + Ti V B Code VDA 239-100 Material no. max. max. max. max. max. max. max. max. max. DP-steel HCT450X 1.0937 0.14 0.75 2.00 0.080 0.015 0.015 – 1 1.00 0.15 0.20 0.005 HCT490X CR290Y490T-DP 1.0939 0.14 0.75 2.00 0.080 0.015 0.015 – 1 1.00 0.15 0.20 0.005 HCT590X CR330Y590T-DP 1.0941 0.15 0.75 2.50 0.040 0.015 0.015 – 1.5 1.40 0.15 0.20 0.005 HCT780X CR440Y780T-DP 1.0943 0.18 0.80 2.50 0.080 0.015 0.015 – 2.0 1.40 0.15 0.20 0.005 HCT980X CR590Y980T-DP 1.0944 0.20 1.00 2.90 0.080 0.015 0,015 – 2.0 1.40 0.15 0.20 0.005 HCT980XG 1.0997 0.23 1.00 2.90 0.080 0.015 0.015 – 2 1.40 0.15 0.20 0.005 HCT1180G2 0.23 1.20 2.90 0.080 0.015 0.015 – 1.4 1.20 0.15 0.20 0.005 TRIP-steel HCT690T CR400Y690T-TR 1.0947 0.24 2.00 2.20 0.080 0.015 0.015 – 2 0.60 0.20 0.20 0.005 HCT780T CR450Y780T-TR 1.0948 0.25 2.20 2.50 0.080 0.015 0.015 – 2 0.60 0.20 0.20 0.005 CP-steel HCT600C CR570Y780T-CP 1.0953 0,18 0,80 2,20 0,080 0,015 0,015 – 2,0 1,00 0,15 0,20 0,005 HCT780C CR570Y780T-CP 1.0954 0,18 1,00 2,50 0,080 0,015 0,015 – 2,0 1,00 0,15 0,20 0,005 HCT980C CR780Y980T-CP 1.0955 0,23 1,00 2,70 0,080 0,015 0,015 – 2,0 1,00 0,15 0,22 0,005 MP-steel HCT1180G2 1.0969 0,23 1,20 2,90 0,080 0,015 0,015 – 1,4 1,20 0,15 0,20 0,005


Thicknesses from 0.40 – 3.00 mm from 0.40 – 3.00 mm ab 0.40 – 3.00 mm Widths up to 1,850 mm up to 1,850 mm up to 1,530 mm up to 1,850 mm Lengths --- --- up to 6,000 mm up to 3,000 mm Tolerances Acc. to DIN EN 10131; finer tolerances available by arrangement.

Mechanical properties (lat.)

Steel grade/type Elongation limit Tensile strength Fracture elongation Work hardening- Bake hardening exponent index Rp0,2 Rm A80 n10-UE BH2 N/mm2 N/mm2 % N/mm2 Code VDA 239-100 Material no. min. min. min. min. min. DP-steel HCT450X 1.0937 260 – 340 450 27 0.16 30 HCT490X CR290Y490T-DP 1.0939 290 – 380 490 24 0.15 30 HCT590X CR330Y590T-DP 1.0941 330 – 430 590 20 0.14 30 HCT780X CR440Y780T-DP 1.0943 440 – 550 780 14 – 30 HCT980X CR590Y980T-DP 1.0944 590 – 740 980 10 – 30 HCT980XG CR700Y980T-DP 1.0997 700 – 850 980 8 – 30 TRIP-steel HCT690T CR400Y690T-TR 1.0947 400 – 520 690 23 0.19 40 HCT780T CR450Y780T-TR 1.0948 450 – 570 780 21 0.16 40 CP-steel HCT600C 1.0953 350 – 500 600 16 – 30 HCT780C CR570Y780T-CP 1.0954 570 – 720 780 10 – 30 HCT980C CR780Y980T-CP 1.0955 780 – 950 980 6 – 30MP-steel HCT1180G2 1.0969 900 – 1,150 1,180 4 – 30

SurfacesGrade Roughness TreatmentDIN EN 10130 b- esp. smooth Ra ≤ 0.4 µmNormal surface A (03) g- smooth Ra ≤ 0.9 µm oiled m- matt Ra > 0.6 µm ≤ 1.9 µmBest surface B (05) r- rough Ra > 1.6 µm un-oiled

On request, these steels can be ordered in accordance with the steel manufacturer’s individual data sheets.

21


Thicknesses from 0.40 – 3.00 mm from 0.40 – 3.00 mm from 0.40 – 3.00 mm Widths up to 1,850 mm up to 1,850 mm up to 1,530 mm up to 1,850 mm Lengths --- --- up to 6,000 mm up to 3,000 mmTolerances Acc. to DIN EN 10131; finer tolerances available by arrangement.

Chemical composition and mechanical properties Steel grade/type Symbol for the Re

1) Rm A80 2) r90

3) 4) n90 3) Chemical composition

type of (Melt analysis) surface C P S Mn Ti Code VDA 239-100 Material no. finishing N/mm2 N/mm2 min. % min. min. max. % max. % max. % max. % max. % DC01 CR1 1.0330 +ZE -/280 270 – 410 28 – – 0.12 0.045 0.045 0.60 – DC03 CR2 1.0347 +ZE -/240 270 – 370 34 1.3 – 0.10 0.035 0.035 0.45 – DC04 CR3 1.0338 +ZE -/220 270 – 350 37 1.6 0.170 0.08 0.030 0.030 0.40 – DC05 CR4 1.0312 +ZE -/200 270 – 330 39 1.9 0.190 0.06 0.025 0.025 0.35 – DC06 CR5 1.0873 +ZE -/180 270 – 350 41 2.1 0.210 0.02 0.020 0.020 0.25 0.3 DC07 1.0898 +ZE -/160 250 – 310 43 2.5 0.220 0.01 0.020 0.020 0.20 0.2

Soft grades – electrolytically galvanized cold-rolled flat products of steel DIN EN 10152 : 2017

1) For products with no clear yield point, the values for the 0.2 % elongation limit (Rp0,2), are taken as those for the yield point. For other products, those for the lower yield point (ReL) apply. For thicknesses of ≤ 0.70 mm, but > 0.50 mm, a 20 MPa higher maximum yield point value is permissible. For thicknesses ≤ 0.50 mm, a higher maximum yield point value of 40 MPa is permissible.2) For thicknesses of ≤ 0.70 mm, but > 0.50 mm, the minimum values for fracture elongation are reduced by 2 units, for thicknesses of ≤ 0.50 mm by 4 units.3) The r90- and n90-value, determined in acc. with 7.5.2.3, only apply for product thicknesses of > 0.50 mm.4) For thickness > 2 mm, the r90-value sis reduced by 0.2.

IX. Electrolytically galvanized sheet

22




Microalloyed grades – cold-rolled flat products with high yield point for cold forming made of microalloyed steels DIN EN 10268 : 2007. With additional coating specifications, this standard also applies for electrolytically galvanized flat products, e.g. H240LA + ZE 75/75

Mechanical properties (lat.) Steel grade/type 0,2 % Higher yield Tensile strength Fracture Vertical Vertical Work hardening Elongation limit1) point through elongation 3) anisotropy anisotropy 2) 3) 4) exponent 4) heat treatment 2) Rp0,2

1) BH2 Rm A80 r r n Code VDA 239-100 Material no. N/mm2 N/mm2 N/mm2 min. lat. % max. lat. min. lat. min lat. HC180Y CR180IF 1.0922 180 – 230 330 – 400 35 1.7 0.19 HC180B CR180BH 1.0395 180 – 230 35 290 – 360 34 1.6 0.17 HC220Y CR210IF 1.0925 220 – 270 340 – 420 33 1,6 0.18 HC220I 1.0346 220 – 270 300 – 380 34 1.4 0.18 HC220B CR210BH 1.0396 220 – 270 35 320 – 400 32 1.5 0.16 HC260Y CR240IF 1.0928 260 – 320 380 – 440 31 1.4 0.17 HC260I 1.0349 260 – 310 320 – 400 32 1.4 0.17 HC260B CR240BH 1.0400 260 – 320 35 360 – 440 29 HC260LA CR240LA 1.0480 260 – 330 350 – 430 26 HC300I 1.0447 300 – 350 340 – 440 30 1.4 0.16 HC300B 1.0444 300 – 360 35 390 – 480 26 HC300LA CR270LA 1.0489 300 – 380 380 – 480 23 HC340LA CR300LA 1.0548 340 – 420 410 – 510 21 HC380LA CR340LA 1.0550 380 – 480 440 – 580 19 HC420LA CR380LA 1.0556 420 – 520 470 – 600 17 HC460LA 1.0574 460 – 580 510 – 660 13 HC500LA 1.0573 500 – 620 550 – 710 12

1) If a yield point is pronounced, the values for the lower yield point (ReL) apply.2) For thicknesses > 1.2 mm, special arrangements must be made.3) For thicknesses ≤ 0.7 mm, but > 0.5 mm, minimum values for breaking elongation of two units lower are permissible.4) The minimum values for r (lat.) and n (lat.) only apply to product thicknesses > 0.5 mm.5) For product thicknesses > 2 mm, the r90-value is reduced by 0.2.

Chemical composition after melt analysis Steel grade/type C Si Mn P S Al Ti Nb Code VDA 239-100 Material no. max. % max. % max. % max. % max. % min. % max. % max. % HC180Y CR180IF 1.0922 0.01 0.3 0.7 0.06 0.025 0.01 0.12 0.09 HC180B CR180BH 1.0395 0.06 0.5 0.7 0.06 0.030 0.015 HC220Y CR210IF 1.0925 0.01 0.3 0.9 0.08 0.025 0.01 0.12 0.09 HC220I 1.0346 0.07 0.5 0.6 0.05 0.025 0.015 0.05 HC220B CR210BH 1.0396 0.08 0.5 0.7 0.085 0.030 0.015 HC260Y CR240IF 1.0928 0.01 0.3 1.6 0.1 0.025 0.01 0.12 0.09 HC260I 1.0349 0.07 0.5 1.2 0.05 0.025 0.015 0.05 HC260B CR240BH 1.0400 0.1 0.5 1.0 0.1 0.030 0.015 HC260LA CR240LA 1.0480 0.1 0.5 1.0 0.030 0.025 0.015 0.15 0.09 HC300I 1.0447 0.08 0.5 0.7 0.08 0.025 0.015 0.05 HC300B 1.0444 0.1 0.5 1.0 0.12 0.030 0.015 HC300LA CR270LA 1.0489 0.12 0.5 1.4 0.030 0.025 0.015 0.15 0.09 HC340LA CR300LA 1.0548 0.12 0.5 1.5 0.030 0.025 0.015 0.15 0.09 HC380LA CR340LA 1.0550 0.12 0.5 1.6 0.030 0.025 0.015 0.15 0.09 HC420LA CR380LA 1.0556 0.14 0.5 1.6 0.030 0.025 0.015 0.15 0.09 HC460LA 0.14 0.6 1.8 0.030 0.025 0.015 0.15 0.009 HC500LA 0.14 0.6 1.8 0.030 0.025 0.015 0.15 0.009

23




Multiphase steels – cold-rolled products made of multiphase steels for cold forming prEN 10338 : 2007 (draft)

Chemical composition (Melt analysis) Steel grade/type Percentage by mass % C Si Mn P S

Altotal

Cr + Mo Nb + Ti V B Code VDA 239-100 Material no. max. max. max. max. max. max. max. max. max. DP-steel HCT450X 1.0937 0.14 0.75 2.00 0.080 0.015 0.015 – 1 1.00 0.15 0.20 0.005 HCT490X CR290Y490T-DP 1.0939 0.14 0.75 2.00 0.080 0.015 0.015 – 1 1.00 0.15 0.20 0.005 HCT590X CR330Y590T-DP 1.0941 0.15 0.75 2.50 0.040 0.015 0.015 – 1.5 1.40 0.15 0.20 0.005 HCT780X CR440Y780T-DP 1.0943 0.18 0.80 2.50 0.080 0.015 0.015 – 2.0 1.40 0.15 0.20 0.005 HCT980X CR590Y980T-DP 1.0944 0.20 1.00 2.90 0.080 0.015 0,015 – 2.0 1.40 0.15 0.20 0.005 HCT980XG 1.0997 0.23 1.00 2.90 0.080 0.015 0.015 – 2 1.40 0.15 0.20 0.005 HCT1180G2 0.23 1.20 2.90 0.080 0.015 0.015 – 1.4 1.20 0.15 0.20 0.005 TRIP-steel HCT690T CR400Y690T-TR 1.0947 0.24 2.00 2.20 0.080 0.015 0.015 – 2 0.60 0.20 0.20 0.005 HCT780T CR450Y780T-TR 1.0948 0.25 2.20 2.50 0.080 0.015 0.015 – 2 0.60 0.20 0.20 0.005 CP-steel HCT600C CR570Y780T-CP 1.0953 0,18 0,80 2,20 0,080 0,015 0,015 – 2,0 1,00 0,15 0,20 0,005 HCT780C CR570Y780T-CP 1.0954 0,18 1,00 2,50 0,080 0,015 0,015 – 2,0 1,00 0,15 0,20 0,005 HCT980C CR780Y980T-CP 1.0955 0,23 1,00 2,70 0,080 0,015 0,015 – 2,0 1,00 0,15 0,22 0,005 MP-steel HCT1180G2 1.0969 0,23 1,20 2,90 0,080 0,015 0,015 – 1,4 1,20 0,15 0,20 0,005

Mechanical properties (lat.)

Steel grade/type Elongation limit Tensile strength Fracture elongation Work hardening- Bake hardening exponent index Rp0,2 Rm A80 n10-UE BH2 N/mm2 N/mm2 % N/mm2 Code VDA 239-100 Material no. min. min. min. min. min. DP-steel HCT450X 1.0937 260 – 340 450 27 0.16 30 HCT490X CR290Y490T-DP 1.0939 290 – 380 490 24 0.15 30 HCT590X CR330Y590T-DP 1.0941 330 – 430 590 20 0.14 30 HCT780X CR440Y780T-DP 1.0943 440 – 550 780 14 – 30 HCT980X CR590Y980T-DP 1.0944 590 – 740 980 10 – 30 HCT980XG CR700Y980T-DP 1.0997 700 – 850 980 8 – 30 TRIP-steel HCT690T CR400Y690T-TR 1.0947 400 – 520 690 23 0.19 40 HCT780T CR450Y780T-TR 1.0948 450 – 570 780 21 0.16 40 CP-steel HCT600C 1.0953 350 – 500 600 16 – 30 HCT780C CR570Y780T-CP 1.0954 570 – 720 780 10 – 30 HCT980C CR780Y980T-CP 1.0955 780 – 950 980 6 – 30MP-steel HCT1180G2 1.0969 900 – 1,150 1,180 4 – 30

On request, these steels can be ordered in accordance with the steel manufacturer’s individual data sheets.

24

Electrolytically galvanized sheetEN10346:2015

1) If the yield point is not pronounced, the values for the 0.2 % elongation limit (Rp0,2) apply, if pronounced, the values for the lower yield point (ReL) apply.2) Reduced minimum values for fracture elongation apply for product thicknesses of: 0.50 mm < t ≤ 0.70 mm (2 units less). 0.35 mm < t ≤ 0.50 mm (minus 4 units) and t ≤ 0.35 mm (minus 7 units).3) For class A surfaces, the maximum value for the yield point is Re = 360 MPa.4) For 1.5 mm < t < 2 mm, the r90-minimum value is reduced by 0.2. For t ≥ 2 mm, the r90-minimum value is reduced by 0.4.

5) The r90- minimum value is reduced for product thicknesses of: 0.50 mm < t ≤ 0.70 mm by 0.2; 0.35 mm < t ≤ 0.50 mm by 0.4 and t ≤ 0.35 mm by 0.6. The n90- minimum value is reduced for product thicknesses of: 0.50 mm < t ≤ 0.70 mm by 0.01; 0.35 mm < t ≤ 0.50 mm by 0.03 and t ≤ 0.35 mm um 0.04.6) Please note the minimum fracture elongation value for DX55D +S products, which does not follow the usual system. DX55D + AS products are marked according to the best heat resistance. (1 MPa = 1 N/mm2)


Surfaces03 Normal surface A 05 Best surface B



Subsequent processingP = Phosphatized C = Chemically passivatedPC = Phosphatized and chemically passivated CO = Chemically passivatedPCO = Phosphatized, chemically passivated and oiled and oiledPO = Phosphatized and oiled O = OiledS = Sealed

Surfaces

Organic coating in acc. with DBL 4062Coating type (AA) Sheet side A Sheet side B .51 5 μm zinc with as sheet side A organic coating* .68 7.5 μm zinc with 7.5 μm zinc without organic organic coating* coating and without pre-phosphatizing* Organic coating: GRANOCOAT ZE, GARDO PROTECT

Plating, zincDescription VDA 239-100 Nominal zinc layer Minimum zinc layer on each side on each sideTwo-sided Thickness µm Weight g/m2 Thickness µm Weight g/m2

ZE 25/25 EG18 2.5 18 1.7 12 ZE 50/50 EG29 5.0 36 4.1 29 ZE 75/75 EG53 7.5 54 6.6 47 ZE 100/100 EG70 10.0 72 9.1 65One-sided Nominal zinc layer Minimum zinc layer on one side on one sideZE 25/0 2.5 18 1.7 12 ZE 50/0 5.0 36 4.1 29 ZE 75/0 7.5 54 6.6 47 ZE 100/0 10.0 72 9.1 65

25



Mechanical properties (lat.) Steel grade/type Symbol for the Elongation limit Tensile strength Fracture elongation Vertical Work hardening type of Re

1) Rm A80 2) anisotropy exponent

surface MPa MPa % r90 n90 Code VDA 239-100 Material no. finishing min. min. min. DX51D 1.0917 +Z, +ZF, +ZA, +AZ, +AS, +ZM – 270 – 500 22 – – DX52D CR1 1.0918 +Z, +ZF, +ZA, +AZ, +AS, +ZM 140 – 300 3) 270 – 420 26 – – DX53D CR2 1.0951 +Z, +ZF, +ZA, +AZ, +AS, +ZM 140 – 260 270 – 380 30 – – DX54D CR3 1.0952 +Z, +ZA 120 – 220 260 – 350 36 1.6 4) 0.18 DX54D CR3 1.0952 +ZF, +ZM 120 – 220 260 – 350 34 1.4 4) 0.18 DX54D 1.0952 +AZ 120 – 220 260 – 350 36 – – DX54D CR3 1.0952 +AS 120 – 220 260 – 350 34 1.4 4) 5) 0.18 5)

DX55D 6) 1.0962 +AS 140 – 240 270 – 370 30 – – DX56D CR4 1.0963 +Z, +ZA 120 – 180 260 – 350 39 1.9 4) 0.21 DX56D CR4 1.0963 +ZF, +ZM 120 – 180 260 – 350 37 1.7 4) 5) 0.20 5)

DX56D CR4 1.0963 +AS, +AZ 120 – 180 260 – 350 39 1.7 4) 5) 0.20 5)

DX57D CR5 1.0853 +Z, +ZA 120 – 170 260 – 350 41 2.1 4) 0.22 DX57D CR5 1.0853 +ZF, +ZM 120 – 170 260 – 350 39 1.9 4) 5) 0.21 4)

DX57D CR5 1.0853 +AS 120 – 170 260 – 350 41 1.9 4) 5) 0.21 4)

Soft grades – hot-dip coated steel strip and sheet made of soft steels acc. to DIN EN 10346 : 2015

Chemical composition (melt analysis) of soft steels for cold forming Steel grade/type Symbol for the Chemical composition Percentage by mass % type of surface C Si Mn P S Ti Code VDA 239-100 Material no. finishing max. max. max. max. max. max. DX51D 1.0917 +Z, +ZF, +ZA, +AZ, +AS, +ZM 0.18 0.5 1.20 0.12 0.045 0.30 DX52D CR1 1.0918 +Z, +ZF, +ZA, +AZ, +AS, +ZM 0.12 0.5 0.60 0.10 0.045 0.30 DX53D CR2 1.0951 +Z, +ZF, +ZA, +AZ, +AS, +ZM 0.12 0.5 0.60 0.10 0.045 0.30 DX54D CR3 1.0952 +Z, +ZF, +ZA, +AZ, +AS, +ZM 0.12 0.5 0.60 0.10 0.045 0.30 DX55D 1.0962 +AS 0.12 0.5 0.60 0.10 0.045 0.30

DX56D CR4 1.0963 +Z, +ZF, +ZA, +AS, +ZM 0.12 0.5 0.60 0.10 0.045 0.30 DX57D CR5 1.0853 +Z, +ZF, +ZA, +AS, +ZM 0.12 0.5 0.60 0.10 0.045 0.30

Z = Hot-dip galvanized ZF = Galvannealed ZA = Galfan AZ = Galvalume AS = Hot-dip aluminized

Mechanical properties (long.)

Steel grade/type Symbol for the Elongation Zugfestigkeit Bruchdehnung type of surface limit strength elongation finishing Rp0,2

1) Rm 2) A80

3) Code Material no. min. min. min. S220GD 1.0241 +Z, +ZF, +ZA, +AZ, +ZM 220 300 20 S250GD 1.0242 +Z, +ZF, +ZA, +AZ, +AS, +ZM 250 330 19 S280GD 1.0244 +Z, +ZF, +ZA, +AZ, +AS, +ZM 280 360 18 S320GD 1.0250 +Z, +ZF, +ZA, +AZ, +AS, +ZM 320 390 17 S350GD 1.0529 +Z, +ZF, +ZA, +AZ, +AS, +ZM 350 420 16 S390GD 1.0238 +Z, +ZF, +ZA, +ZM, +AZ 390 460 16 S420GD 1.0239 +Z, +ZF, +ZA, +ZM, +AZ 420 480 15 S450GD 1.0233 +Z, +ZF, +ZA, +ZM, +AZ 450 510 14 S550GD 1.0531 +Z, +ZF, +ZA, +AZ, +ZM 550 560 –

Construction steels – continuously hot-dip coated steel strip and sheet made of construction steels acc. to DIN EN 10346 : 2015

Chemische Zusammensetzung (Schmelzanalyse) Percentage by mass % C Si Mn P S max. max. max. max. max. 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045 0,20 0,60 1,70 0,10 0,045

1) If the yield point is pronounced, the values for the upper yield point (ReH) apply. 2) For all steel grades, with the exception of S55OGD, a range of 140 MPa can be expected for tensile strength.3) Reduced minimum values for fracture elongation apply for product thicknesses of t > 0.50 mm (4 units less) and for 0.50 mm < t ≤ 0.70 mm (2 units less).

X. Hot-dip galvanized sheet

26

B = Bake-hardening LA = Low alloy (microalloyed) Y = Interstitial free (IF Steel)




Mechanical properties (lat.) Steel grade/type Symbol for the 0,2 % Elongation Bake hardening Tensile strength Fracture Vertical Work hardening type of limit index elongation anisotropy exponent surface Rp0,2

1) BH2 MPa Rm A80 2) 3) r90

3) 4) n90 finishing min. MPa % Code VDA 239-100 Material no. N/mm2 N/mm2 N/mm2 min. quer min. min. HX160YD 1.0910 +Z, +ZF, +ZA, +AZ, +AS, +ZM 160 – 220 – 300 – 360 37 1,9 0,20 HX180YD 1.0921 +Z, +ZF, +ZA, +AZ, +AS, +ZM 180 – 240 – 330 – 390 34 1,7 0,18 HX180BD 1.0914 +Z, +ZF, +ZA, +AZ, +AS, +ZM 180 – 240 30 290 – 360 34 1,5 0,16 HX220YD 1.0923 +Z, +ZF, +ZA, +AZ, +AS, +ZM 220 – 280 – 340 – 420 32 1,5 0,17 HX220BD 1.0919 +Z, +ZF, +ZA, +AZ, +AS, +ZM 220 – 280 30 320 – 400 32 1,2 0,15 HX260YD 1.0926 +Z, +ZF, +ZA, +AZ, +AS, +ZM 260 – 320 – 380 – 440 30 1,4 0,16 HX260BD 1.0924 +Z, +ZF, +ZA, +AZ, +AS, +ZM 260 – 320 30 360 – 440 28 – – HX260LAD CR240LA 1.0929 +Z, +ZF, +ZA, +AZ, +AS, +ZM 260 – 330 – 350 – 430 26 – – HX300YD 1.0927 +Z, +ZF, +ZA, +AZ, +AS, +ZM 300 – 360 – 390 – 470 27 1,3 0,15 HX300BD 1.0930 +Z, +ZF, +ZA, +AZ, +AS, +ZM 300 – 360 30 400 – 480 26 – – HX300LAD CR270LA 1.0932 +Z, +ZF, +ZA, +AZ, +AS, +ZM 300 – 380 – 380 – 480 23 – – HX340BD 1.0945 +Z, +ZF, +ZA, +AZ, +AS, +ZM 340 – 400 30 440 – 520 24 – – HX340LAD CR300LA 1.0933 +Z, +ZF, +ZA, +AZ, +AS, +ZM 340 – 420 – 410 – 510 21 – – HX380LAD CR340LA 1.0934 +Z, +ZF, +ZA, +AZ, +AS, +ZM 380 – 480 – 440 – 560 19 – – HX420LAD CR380LA 1.0935 +Z, +ZF, +ZA, +AZ, +AS, +ZM 420 – 520 – 470 – 590 17 – – HX460LAD CR420LA 1.0990 +Z, +ZF, +ZA, +AZ, +AS, +ZM 460 – 560 – 500 – 640 15 – – HX500LAD CR460LA 1.0991 +Z, +ZF, +ZA, +AZ, +AS, +ZM 500 – 620 – 530 – 690 13 – –

Microalloyed grades – continuously hot-dip coated steel strip and sheet made of steels with a high yield point for cold forming acc. to DIN EN 10346 : 2015

1) If the yield point is pronounced, the values for the lower yield point (ReL) apply2) Reduced minimum values for fracture elongation apply for product thicknesses of: 0.50 mm < t ≤ 0.70 mm (minus 2 units) 0.35 mm < t ≤ 0.50 mm (minus 4 units) and t ≤ 0.35 mm (minus 7 units).3) For AS, AZ and ZF coatings, the A80 minimum values are reduced by 2 units and the r90 minimum values by 0.2.4) For product thicknesses1.5 mm < t < 1.99 mm, the r90-minimum values are reduced by 0.2. For product thicknessest ≥ 2 mm, the r90-minimum values are reduced by 0.4.

5) The r90- minimum value is reduced for product thicknesses of: 0.50 mm < t ≤ 0.70 mm um 0.2; 0.35 mm < t ≤ 0.50 mm um 0.4 und t ≤ 0.35 mm um 0.6. The n90-minimum value is reduced for product thicknesses of: 0.50 mm < t ≤ 0.70 mm um 0.01; 0.35 mm < t ≤ 0.50 mm um 0.03 und t ≤ 0.35 mm um 0.04. (1 MPa = 1 N/mm2)

Chemical composition (Melt analysis) Steel grade/type Symbol for the Chemical composition type of Percentage by mass % surface C Si Mn P S Algesamt Nb Ti Code VDA 239-100 Material no. finishing max. max. max. max. max. max. max. HX160YD 1.0910 +Z, +ZF, +ZA, +AZ, +AS 0.01 0.15 0.70 0.06 0.025 ≤ 0.1 0.09 0.12 HX180YD 1.0921 +Z, +ZF, +ZA, +AZ, +AS 0.01 0.20 0.70 0.06 0.025 ≤ 0.1 0.09 0.12 HX180BD 1.0914 +Z, +ZF, +ZA, +AZ, +AS 0.10 0.50 0.70 0.06 0.025 ≤ 0.1 0.09 0.12 HX220YD 1.0923 +Z, +ZF, +ZA, +AZ, +AS 0.01 0.20 0.90 0.08 0.025 ≤ 0.1 0.09 0.12 HX220BD 1.0919 +Z, +ZF, +ZA, +AZ, +AS 0.10 0.50 0.70 0.08 0.025 ≤ 0.1 0.09 0.12 HX260YD 1.0926 +Z, +ZF, +ZA, +AZ, +AS 0.01 0.25 1.30 0.10 0.025 ≤ 0.1 0.09 0.12 HX260BD 1.0924 +Z, +ZF, +ZA, +AZ, +AS 0.10 0.50 0.80 0.10 0.025 ≤ 0.1 0.09 0.12 HX260LAD CR240LA 1.0929 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 0.60 0.030 0.025 ≥ 0.015 0.09 0.12 HX300YD 1.0927 +Z, +ZF, +ZA, +AZ, +AS 0.015 0.30 1.60 0.10 0.025 ≤ 0.1 0.09 0.12 HX300BD 1.0930 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 0.80 0.12 0.025 ≤ 0.1 0.09 0.12 HX300LAD CR270LA 1.0932 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 1.00 0.030 0.025 ≤ 0.1 0.09 0.15 HX340BD 1.0945 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 0.80 0.12 0.025 ≤ 0.1 0.09 0.12 HX340LAD CR300LA 5) 1.0933 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 1.00 0.030 0.025 ≥ 0.015 0.09 0.15 HX380LAD CR340LA 5) 1.0934 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 1.40 0.030 0.025 ≥ 0.015 0.09 0.15 HX420LAD CR380LA 1.0935 +Z, +ZF, +ZA, +AZ, +AS 0.11 0.50 1.40 0.030 0.025 ≥ 0.015 0.09 0.15 HX460LAD CR420LA 5) 1.0990 +Z, +ZF, +ZA, +AZ, +AS 0.15 0.50 1.70 0.030 0.025 ≥ 0.015 0.09 0.15 HX500LAD CR460LA 5) 1.0991 +Z, +ZF, +ZA, +AZ, +AS 0.15 0.50 1.70 0.030 0.025 ≥ 0.015 0.09 0.15

27



Mechanical properties (lat.) cold-rolled products Steel grade/type Symbol for the Elongation limit Tensile strength Fracture Work hardening Bake hardening type of elongation exponent index surface Rp0,2

1) Rm A80 1) 2) n10-UE BH2

finishing MPa MPa % MPa Code VDA 239-100 Material no. min. min. min. min. DP-steel HCT450X 1.0937 +Z, +ZF, +ZA, +ZM 260 – 340 450 27 0.16 30 HCT490X CR290Y490T-DP 1.0995 +Z, +ZF, +ZA, +ZM 290 - 380 490 24 0.15 30 HCT590X CR330Y590T-DP 1.0996 +Z, +ZF, +ZA, +ZM 330 – 430 590 20 0.14 30 HCT780X CR440Y780T-DP 1.0943 +Z, +ZF, +ZA, +ZM 440 – 550 780 14 – 30 HCT980X CR590Y980T-DP 1.0944 +Z, +ZF, +ZA, +ZM 590 – 740 980 10 – 30 HCT980XG 1.0997 +Z, +ZF, +ZA, +ZM 700 – 850 980 8 – 30 TRIP-steel HCT690T CR400Y690T-TR 1.0947 +Z, +ZF, +ZA, +ZM 400 – 520 690 23 0.19 40 HCT780T 1.0948 +Z, +ZF, +ZA, +ZM 450 – 570 780 21 0.16 40 CP-steel HCT600C 1.0953 +Z, +ZF, +ZA, +ZM 350 – 500 600 16 – 30 HCT780C CR570Y780T-CP 1.0954 +Z, +ZF, +ZA, +ZM 570 – 720 780 10 – 30 HCT980C 1.0955 +Z, +ZF, +ZA, +ZM 780 – 950 980 6 – 30

Multiphase steels – continuous electrolytic strip and sheet made of multiphase steels for cold forming acc. to EN 10346 : 2015

Mechanical properties (lat.) warm-rolled products Steel grade/type Symbol for the Elongation limit Tensile strength Fracture Work hardening type of elongation exponent surface Rp0,2

1) Rm A80 1) 2) n10-UE

finishing MPa MPa % Code VDA 239-100 Material no. min. min. min. FB-steel HDT450F HR300Y450T-FB 1.0961 +Z, +ZF, +ZM 300 – 420 450 24 – HDT580F HR440Y580T-FB 1.0994 +Z, +ZF, +ZM 460 – 620 580 15 – DP-steel HDT580X HR330Y580T-DP 1.0936 +Z, +ZF, +ZM 330 – 450 580 19 0.13 CP-steel HDT750C 1.0956 +Z, +ZF, +ZM 620 – 760 750 10 – HDT760C HR660Y760T-CP 1.0998 +Z, +ZF, +ZM 660 – 830 760 10 – HDT950C 1.0958 +Z, +ZF, +ZM 720 – 950 950 9 –

1) Reduced minimum values for Fracture Elongation apply for product thicknesses of t ≤ 0.5 mm (4 units less) and for 0.5 < t ≤ 0.7 mm (2 units less).2) Fracture elongation values of two units less apply for ZF coatings.


28

SurfacesSurface types NA = Usual zinc spangle in different sizes with usual surfaceMA= Small zinc spangle with usual surfaceMB = Re-rolled with improved surfaceMC = Re-rolled with best surfaceRA = Usual surface zinc/iron alloyRB = Improved surface zinc/iron alloyRC = Best surface zinc/iron alloy

Subsequent surface treatment C = Chemically passivatedO = OiledCO = Chemically passivated and oiledP = PhosphatizedPO = Phosphatized and oiledS = SealedU = Untreated

Coating processes +Z = Galvanised (99 % Zn)+ZF = Zinc-iron alloy (galvanealed)+ZA = Zinc/aluminium (Galfan, Zn + 5 % Al)+AZ = Aluminium/zinc (Galvalume 55 % Al + 1.6 % Sl + Zn)+AS = Aluminium-silicon coating (11 % Sl + Al)+ZM = Zinc-magnesium (1 – 2 % Mg + 1-2 % Al + Zn)* * yet standardised in EN 10246, available in various

qualities and coating volumes.




Multiphase steels – continuous electrolytic strip and sheet made of multiphase steels for cold forming acc. to EN 10346 : 2015

Chemical composition (Melt analysis) Steel grade/type Symbol for the Chemical composition type of Percentage by mass % surface C Si Mn P S Altotal Cr + Mo Nb + Ti V B Code 1) VDA 239-100 Material no. finishing max. max. max. max. max. max. max. max. max. FB-steel HDT450F 1.0961 +Z, +ZF, +ZM 0.18 0.50 2 0.050 0.010 0.015 – 2 1 0.15 0.15 0.005 HDT580F 1.0994 +Z, +ZF, +ZM 0.18 0.50 2 0.050 0.010 0.015 – 2 1 0.15 0.15 0.01 DP-steel HCT450X 1.0937 +Z, +ZF, +ZA, +ZM 0.14 0.75 2.00 0.080 0.015 0.015 – 1 1.00 0.15 0.20 0.005 HCT490X CR290Y490T-DP 1.0995 +Z, +ZF, +ZA, +ZM 0.14 0.75 2.00 0.080 0.015 0.015 – 1 1.00 0.15 0.20 0.005 HCT590X CR330Y590T-DP 1.0996 +Z, +ZF, +ZA, +ZM 0.15 0.75 2.50 0.040 0.015 0.015 – 1.5 1.40 0.15 0.20 0.005 HDT580X HR330Y580T-DP 1.0936 +Z, +ZF, +ZM 0.14 1.00 2.20 0.085 0.015 0.015 – 1 1.40 0.15 0.20 0.005 HCT780X CR440Y780T-DP 1.0943 +Z, +ZF, +ZA, +ZM 0.18 0.80 2.50 0.080 0.015 0.015 – 2.00 1.40 0.15 0.20 0.005 HCT980X CR590Y980T-DP 1.0944 +Z, +ZF, +ZA, +ZM 0.20 1.00 2.90 0.080 0.015 0.015 – 2.00 1.40 0.15 0.20 0.005 HCT980XG 1,0997 +Z, +ZF, +ZA, +ZM 0.23 1.00 2.90 0.080 0.015 0.015 – 2.00 1.40 0.15 0.20 0.005 TRIP-steel HCT690T 1.0947 +Z, +ZF, +ZA, +ZM 0.24 2.00 2.20 0.080 0.015 0.015 – 2.00 0.60 0.20 0.20 0.005 HCT780T 1.0948 +Z, +ZF, +ZA, +ZM 0.25 2.20 2.50 0.080 0.015 0.015 – 2.00 0.60 0.20 0.20 0.005 CP-steel HCT600C 1.0953 +Z, +ZF, +ZA, +ZM 0.18 0.80 2.20 0.080 0.015 0.015 – 2.00 1.00 0.15 0.20 0.005 HDT750C 1.0956 +Z, +ZF, +ZM 0.18 0.80 2.20 0.080 0.015 0.015 – 2.00 1.00 0.15 0.20 0.005 HCT780C CR570Y780T-CP 1.0954 +Z, +ZF, +ZA, +ZM 0.18 1.00 2.50 0.080 0.015 0.015 – 2.00 1.00 0.15 0.20 0.005 HDT760C HR660Y760T-CP 1.0998 +Z, +ZF, +ZM 0.18 1.00 2.50 0.080 0.015 0.015 – 2.00 1.00 0.25 0.20 0.005 HDT950C 1.0958 +Z, +ZF, +ZM 0.25 0.80 2.70 0.080 0.015 0.015 – 2.00 1.20 0.25 0.30 0.005 HCT980C 1.0955 +Z, +ZF, +ZA, +ZM 0.23 1.00 2.70 0.080 0,.015 0.015 – 2.00 1.00 0.15 0.22 0.005

1) C = Cold-rolled products D = Warm-rolled products

F = Ferritic-bainitic X = Dual phase T = TRIP C = Complex phase M = Martensitic

29



Available coating types

Minimum coating volume, Theoretical reference value Density Coating code no. VDA 239-100 on both sides, for coating thickness per side in g/m2 µm g/cm3

Dreiflächenprobe Einzelflächenprobe Typischer Wert 1) Bereich 2)

Zinc coating volume (Z) Z100 GI 40 100 85 7 5 – 12 7.1 Z140 GI 60 140 120 10 7 – 15 7.1 Z200 GI 85 200 170 14 10 – 20 7.1 Z225 225 195 16 11 – 22 7.1 Z275 275 235 20 13 – 27 7.1 Z350 350 300 25 17 – 33 7.1 Z450 450 385 32 22 – 42 7.1 Z600 600 510 42 29 – 55 7.1Zinc/iron alloy coating volume (ZF) ZF100 GA 40 100 85 7 5 – 12 7.1 ZF120 GA 50 120 100 8 6 – 13 7.1Zinc/aluminium alloy coating volume (ZA) ZA095 95 80 7 5 – 12 6.9 ZA130 130 110 10 7 – 15 6.9 ZA185 185 155 14 10 – 20 6.9 ZA200 200 170 15 11 – 21 6.9 ZA255 255 215 20 15 – 27 6.9 ZA300 300 255 23 17 – 31 6.9Aluminium/zinc alloy coating volume (AZ) not for multiphase steels AZ100 100 85 13 9 – 19 3.8 AZ150 150 130 20 15 – 27 3.8 AZ185 185 160 25 19 – 33 3.8Aluminium/silicon alloy coating volume (AS) not for multiphase steels AS060 60 45 8 6 – 13 3.0 AS080 AS 30 80 60 14 10 – 20 3.0 AS100 100 75 17 12 – 23 3.0 AS120 AS 45 120 90 20 15 – 27 3.0 AS150 150 115 25 19 – 33 3.0Coating volume of zinc-magnesium alloy (ZM)3) ZM060 60 50 4,5 4 – 8 6.2 – 6.6 ZM070 ZM30 70 60 5,5 4 – 8 6.2 – 6.6 ZM080 80 70 6 4 – 10 6.2 – 6.6 ZM090 90 75 7 5 – 10 6.2 – 6.6 ZM100 ZM40 100 85 8 5 – 11 6.2 – 6.6 ZM120 ZM50 120 100 9 6 – 14 6.2 – 6.6 ZM130 130 110 10 7 – 15 6.2 – 6.6 ZM140 140 120 11 8 – 16 6.2 – 6.6 ZM150 150 130 11,5 8 – 17 6.2 – 6.6 ZM160 160 130 12 8 – 17 6.2 – 6.6 ZM175 175 145 13 9 – 18 6.2 – 6.6 ZM190 190 160 15 10 – 20 6.2 – 6.6 ZM200 200 170 15 10 – 20 6.2 – 6.6 ZM250 250 215 19 13 – 25 6.2 – 6.6 ZM300 300 255 23 17 – 30 6.2 – 6.6 ZM310 310 265 24 18 – 31 6.2 – 6.6 ZM350 350 300 27 19 – 33 6.2 – 6.6 ZM430 430 365 35 26 – 46 6.2 – 6.6

1) Layer thicknesses can be calculated from the coating volumes.2) Users may assume that these limits will be maintained on the top and bottom sides.3) More ZM coatings available on request.


30

XI. Hot stamping steels (22MnB5)

Hot-rolled steels

EN 10.111 DD11 D Flat products for cold forming

D hot-rolled, followed by 2 symbols

EN 10.149 S315MC S Steels for steel construction 315 set minimum yieldin MPA

M Thermomechanically rolled C With special cold formability

EN 10.025 S235JR S Steels for steel construction 235 set minimum yieldin MPA

JR Test temperaturefor impact tests + 20° C

EN 10.025 S235J0 S Steels for steel construction 235 set minimum yieldin MPA

J0 Test temperaturefor impact tests 0° C

EN 10.025 S235J2 S Steels for steel construction 235 set minimum yieldin MPA

J2 Test temperaturefor impact tests - 20° C

EN 10.025 S 185 S Steels for steel construction 185 set minimum yieldin MPA

EN 10.025 E 295 E Engineering steels 295 set minimum yieldin MPA

EN 10.338 HDT450F H Flat products ofhigher-tensile steelsfor cold forming

DT Hot-rolled 450 Set minimum tensile strength in MPA

F Ferritic-bainitic steels

EN 10.338 HDT580X H Flat products ofhigher-tensile steelsfor cold forming


X Dual phase steels

EN 10.338 HDT750C H Flat products ofhigher-tensile steelsfor cold forming


C Complex phase steels

EN 10.338 HDT1180M H Flat products ofhigher-tensile steelsfor cold forming


M Martensitic steels

Norm Examplefor abbre-

viation

Meaning Meaning Meaning Meaning Meaning


Thicknesses, hot-rolled from 1.75 - 3.00 mm from 1.90 - 3.00 mm from 2.00 - 3.00 mm from 2.10 - 3.00 mm from 1.00 - 3.00 mm from 1.00 - 3.00 mm

Thicknesses, cold-rolled from 0.75 - 3.00 mm from 0.90 - 3.00 mm

Thicknesses, hot-dip galvanized from 0.75 - 2.25 mm from 0.75 - 3.00 mm from 0.90 - 3.00 mm

Widths, hot-rolled up to 1,400 mm up to 1,500 mm up to 1,150 mm up to 1,600 mm up to 1,600 mm up to 1,350 mm up to 1,600 mm

Widths cold-rolled up to 1,150 mm up to 1,600 mm

Widths coated up to 1,000 mm up to 1,150 mm up to 1,600 mm

Lengths up to 6,000 mm up to 3,000 mm

Steel manufacturer orAutomobile norm

Hot-rolled Cold-rolled Coated + AS Coated + GI Coated + GA Coating Remarks

Thyssen MBW-W 1500® MBW-K 1500® MBW 1500+AS®MBW 500+AS

Salzgitter 22MnB5 22MnB5

Tata HQ1500HR HQ1500CR

Voest 22MnB5 22MnB5 phs-ultraform® 1500

MBN 11257 CR22MnB5CR22MnB5-CS

CR22MnB5+ASCR22MnB5-CS+AS

CR22MnB5+GICR22MnB5-CS+GI

VW TL 4225 TL 4225 +H TL 4225 +C TL 4225 +H +ASTL 4225 +C +AS

TL 4225 +C +Z

Hot-stamping steels are not EN normed. They are supplied in different manufacturers’ grades and acc. to automobile norms. 1)

1) Selection of deliverable grades. Other grade on request.

Hot-rolled, cold-rolled and coated

XII. Designation system for steels acc. to EN 1027

For the norms listed in the catalogue

31

XII. Designation system for steels acc. to EN 1027

Cold-rolled steels

EN 10.130 DC01 D Flat products for cold forming

C Cold-rolled, followed by2 symbols

EN 10.209 DC01EK D Flat products for cold forming

C Cold-rolled, followed by2 symbols

EK for conventionalenamelling

EN 10.268 HC180Y H Flat products ofhigher-tensile steelsfor cold forming

C cold-rolled 180 Set minimum tensile strength in MPA

Y Interstitialfree Steel (IF-steel)

EN 10.268 HC180P H Flat products ofhigher-tensile steelsfor cold forming


P Phosphorus alloyed

EN 10.268 HC180B H Flat products ofhigher-tensile steelsfor cold forming


B Bake hardening

EN 10.268 HC220I H Flat products ofhigher-tensile steelsfor cold forming


I Isotropic steel

EN 10.268 HC260LA H Flat products ofhigher-tensile steelsfor cold forming


LA Low alloy

EN 10.338 HCT450X H Flat products ofhigher-tensile steelsfor cold forming

CT cold-rolled 450 Set minimum tensile strength in MPA

X Dual phase steels

EN 10.338 HCT690T H Flat products ofhigher-tensile steelsfor cold forming


T TRIP steel

EN 10.338 HCT780C H Flat products ofhigher-tensile steelsfor cold forming




viation


Hot-dip galvanized steels

EN10.346 DX51D D Flat products for cold forming

X Hot or cold rolled,followed by 2 symbols

D für Schmelztauchüberzüge

EN10.346 HX180YD H Flat products ofhigher-tensile steelsfor cold forming

X warm- oder kaltgewalzt 180 Set minimum tensile strength in MPA

Y Interstitialfree Steel (IF-steel) D for hot-dip coatings

EN10.346 HX180BD H Flat products ofhigher-tensile steelsfor cold forming


B Bake hardening D for hot-dip coatings

EN10.346 HX260LAD H Flat products ofhigher-tensile steelsfor cold forming


LA Low alloy D for hot-dip coatings

EN10.346 HDT450F H Flat products ofhigher-tensile steelsfor cold forming

DT hot-rolled 450 Set minimum tensile strength in MPA

F Ferritic-bainitic steels

EN10.346 HDT580X H Flat products ofhigher-tensile steelsfor cold forming


X Dual phase steels

EN10.346 HDT750C H Flat products ofhigher-tensile steelsfor cold forming



EN10.346 HDT1180M H Flat products ofhigher-tensile steelsfor cold forming


M Martensitic steels

EN10.346 HCT450X H Flat products ofhigher-tensile steelsfor cold forming


X Dual phase steels

EN10.346 HCT690T H Flat products ofhigher-tensile steelsfor cold forming


T TRIP steels

EN10.346 HCT780C H Flat products ofhigher-tensile steelsfor cold forming




viation


For the norms listed in the catalogue

32

VII. Unternehmen SCHÄFER WERKEXIII. The SCHÄFER WERKE Group of Companies

EMW Steel Service Centre SCHÄFER Perforated Metal

SCHÄFER IT-Systems

SCHÄFER Interior Systems

SCHÄFER Container Systems

SCHÄFER Industrial Solutions

33

SCHÄFER WERKE – Expertise in steel processing

Within the SCHÄFER Group, SCHÄFER WERKE are the

specialists for the development, manufacture and sale

of fine steel sheet and stainless steel products. Constant

growth and the uncompromising extension of the product

range underline the company‘s successful strategy. The

outstanding success of the individual business areas lies

above all in the ability to put customer wishes into practice

quickly, while keeping the products themselves highly

individual.

The extraordinary speed at which new sheet steel products

can be realised stems from the close co-operation of all

business areas with our own EMW Steel Service Centre,

which, with a storage capacity of 100,000 t of fine steel sheet,

can provide the coils, slit strips, cut-to-size sheets and circular

blanks required for further processing in very high quality

and at very short notice.

SCHÄFER Perforated Metal supply a broad and rapidly

available range of high-quality perforated plates and

sheets for all sectors and application fields.

SCHÄFER Container Systems is one of the world‘s leading

suppliers of reusable stainless steel beverage containers

for beer, wine and soft drinks, as well as for IBCs and special

containers for solid and liquid substances and granulates.

SCHÄFER IT-Systems develops, designs and produces

standardised and made-to-measure network and

server cabinets, as well as data centre and water-cooled

server cabinet solutions.

SCHÄFER Interior Systems develop and manufacture

high-quality steel furniture for workshop and factory floor,

as well as office and administration.

SCHÄFER Industrial Solutions develops, designs and

manufactures customised punched and bent parts, machine

cladding, special and standard housing solutions in metal.

Our great manufacturing expertise, our extensive range

of production equipment and our employees’ outstanding

level of qualification make SCHÄFER the ideal partner for

contract manufacturing. By working with SCHÄFER, our

customers can profit from measurable time and cost-saving

benefits.

34

External sales: Germany North Post codes 32-37, 40-49, 50-59Reinschmidt, Malte +49 (0) 221/20534668 [email protected] PC-Fax +49 (0) 2735/787-1592 Mobile +49 (0) 151/72627091 Post codes 35, 51, 56, 57, 58, 65Preissler, Matthias +49 (0) 2735/[email protected] Fax +49 (0) 2735/787-484 Mobile +49 (0) 160/91708643

External sales: Germany South Post codes 54-56, 6, 75-77, 79Oberkirsch, Freddy +49 (0) 6841/994380 [email protected] Fax +49 (0) 6841/994381 Mobile +49 (0) 170/5633504

Post codes 70-74, 78, 87-89, Austria and SwitzerlandPasternacki, Andreas +49 (0) 7071/7956999 [email protected] Fax +49 (0) 7071/9150738 Mobile +49 (0) 151/14620109

Post codes 80-87, 9, AustriaGaube, Patrick +49 (0) 991/2703152 [email protected] Fax +49 (0) 991/2910964 Mobile +49 (0) 170/5633385

External sales: Germany-East Post codes 0-15, 36-38, 98-99Lippa, Thomas +49 (0) 3641/6360947 [email protected] Fax +49 (0) 3641/6360948 Mobile +49 (0) 151/12143099

Key Account Internationale Group of companiesMüller, Sascha +49 (0) 2735/787-571 [email protected]

Mies, Sandra +49 (0) 2735/787-423 [email protected]

Schneider, Louisa +49 (0) 2735/787-201 [email protected]

Sales management Germany South Richter, Hartmut, ppa. +49 (0) 2735/787-487 [email protected]

Region Germany South/ExportErmert, Peter, Hbv. +49 (0) 2735/787-492 [email protected]

Fichtner, Marco +49 (0) 2735/787-626 [email protected]

Judt, Manuela +49 (0) 2735/787-507 [email protected]

Jung, Matthias +49 (0) 2735/787-382 [email protected]

Kempe, Frank +49 (0) 2735/787-533 [email protected]

Nogaitzig, Ann Christin +49 (0) 2735/787-622 [email protected]

Schlechtriemen, Jana +49 (0) 2735/787-529 [email protected]

Schmidt, Andrea +49 (0) 2735/787-407 [email protected]

Schulte, Klaus-Peter +49 (0) 2735/787-489 [email protected]

Schupp, Daniel +49 (0) 2735/787-542 [email protected]

Stolz, Andreas +49 (0) 2735/787-251 [email protected]

Vogt, Rebecca +49 (0) 2735/787-539 [email protected]

Werthebach, Sandra +49 (0) 2735/787-411 [email protected]

Sales, TradeHennrichs, Michael, a.a.* +49 (0) 2735/787-611 [email protected]

Henrich, Gabriele +49 (0) 2735/787-246 [email protected]

Sturm, André +49 (0) 2735/787-616 [email protected]

XIV. Contact

Division management

Mockenhaupt, Michael +49 (0) 2735/787-532 [email protected]

Assistance of the management: Winkel, Daniela +49 (0) 2735/787-358 [email protected]

Sluga, Andreas +49 (0) 2735/787-352 [email protected]

Sales Germany

Sales management Germany NorthBecker, Henning, ppa. +49 (0) 2735/787-479 [email protected]

Secretariat: Allendorf, Sandra +49 (0) 2735/787-347 [email protected]

Region Germany NorthLieber, Stefan, a.a.* +49 (0) 2735/787-245 (deputy regional manager) [email protected]

Löhr, Dirk, a.a.* +49 (0) 2735/787-530 [email protected]

Brücher, Tanja +49 (0) 2735/787-360 [email protected]

Buhl, Anna-Lena +49 (0) 2735/787-494 [email protected]

Dohndorf, Norman +49 (0) 2735/787-367 [email protected]

Euteneuer, Adrian +49 (0) 2735/787-6405 [email protected]

Hensel, Louisa Katharina +49 (0) 2735/[email protected]

Ippach, Annika +49 (0) 2735/787-486 [email protected]

Kepp, Horst +49 (0) 2735/787-364 [email protected]

Lässig, Jessica +49 (0) 2735/[email protected]

Lück, Sonja +49 (0) 2735/787-207 [email protected]

Preissler, Matthias +49 (0) 2735/787-368 [email protected]

Schlechtriemen, Fabian +49 (0) 2735/787-220 [email protected]

Wagener, Matthias +49 (0) 2735/787-572 [email protected]

* authorized agent

35

@

Quality management / Technical consulting

Quality managementBaumunk, Christian, +49 (0) 2735/787-291 a.a.* (Ltg.) [email protected]

Technical consulting/QualitySchilling, Frank, +49 (0) 2735/787-242 a.a.* (Ltg.) [email protected]

De Spirt, Marco +49 (0) 2735/787-599 [email protected]

Großmann, Carsten +49 (0) 2735/787-286 [email protected]

Arndt, Herwig +49 (0) 2735/[email protected]

Pajestka, David +49 (0) 2735/[email protected] Schmalfuß, Birgit +49 (0) 2735/787-266 [email protected]

Fax +49 (0) 2735/787-288

Production

Brüggemann, Torsten +49 (0) 2735/787-680 [email protected]

Work preparation

Mockenhaupt, Elmar +49 (0) 2735/787-396 [email protected]

Logistic

Müller, Jens +49 (0) 2735/[email protected]

IT-Management

Petri, Julian +49 (0) 2735/787-476 [email protected]

International Sales

Sales Benelux/France Jos Bergmans Mgr. Kuyperslein 2 NL-5556 VS Valkenswaard [email protected] Tel. +31/402049911 Mobile +31/651887324 Fax +31/402043833

Sales Poland Michał Ulman Mobile +48/603248103 [email protected] PC-Fax +49 (0) 2735/787-1991

Individual consultingSheet from EMW.

By e-mail to [email protected]

By fax on +49 (0) 2735/787-484

By telephone on

+49 (0) 2735/787-02

Purchase

Purchase management Latsch, Holger, ppa. +49 (0) 2735/787-470 [email protected]

Secretariat: Winkel, Daniela +49 (0) 2735/787-358 [email protected]

Purchase Hennrichs, Michael, Hbv. +49 (0) 2735/787-611 (deputy purchasing manager) [email protected]

Vehma, Christian, Hbv. +49 (0) 2735/787-496 [email protected]

Henrich, Gabriele +49 (0) 2735/787-246 [email protected]

Hess, Vanessa +49 (0) 2735/787-356 [email protected]

Kreutz, Alfred +49 (0) 2735/787-296 [email protected]

Roth, Marion +49 (0) 2735/787-527 [email protected]

Sturm, André +49 (0) 2735/787-616 [email protected] Tautz, Marius +49 (0) 2735/787-621 [email protected]

36

The EMW Steel Service Centre, the centre of excellence for sheet, is part of the internationally successful

company SCHÄFER WERKE. The owner-led group of companies has its headquarters in Neunkirchen,

in Germany’s Siegerland region.

This owner-led group of companies has its headquarters in Neunkirchen in Germany’s Siegerland

region. The work of all the SCHÄFER WERKE divisions – SCHÄFER IT-Systems, SCHÄFER Industrial

Solutions, SCHÄFER Interior Systems, SCHÄFER Container Systems, SCHÄFER Perforated Metal and

EMW Steel Service Centre – is based on high-quality thin steel sheet. The processing of this material

is one of the core competencies of this enterprise.

Prin

t no.

029

3/10

.17

· We

rese

rve

the

right

to m

ake

tech

nica

l alte

ratio

ns

EMW Stahl Service GmbHPfannenbergstraße 1D-57290 Neunkirchen/SiegerlandPhone +49 (0) 2735/787-02 · Fax +49 (0) 2735/787-484E-Mail: [email protected]

Head office and production site at Neunkirchen (D)

Our location

Date post:	08-Aug-2018
Category:	Documents
Upload:	lamliem
View:	221 times
Download:	0 times

The Centre of Excellence for sheet - emw-stahlservice.de · The Centre of Excellence for sheet –...

Documents