2005 Honda Motor Co., Ltd.
No part of this publication may be reproduced without written permission.
This publication includes the latest production information available before printing. HondaMotor Co., Ltd. reserves the right to make changes at any time without notice and withoutincurring any obligation.
This manual should be considered a permanent part of the motorcycle and should remainwith the motorcycle when it is resold.
The vehicle pictured on the front cover may not match your vehicle.
05/06/09 15:46:15 31MBZ610_001
2006Honda CB600F599OWNER’S MANUAL
05/06/09 15:46:17 31MBZ610_002
-
Introduction
Introduction
Congratulations on choosing your Hondamotorcycle.
When you own a Honda, you’re part of aworldwide family of satisfied customers
people who appreciate Honda’sreputation for building quality into everyproduct.
Before riding, take time to get acquaintedwith your motorcycle and how it works.To protect your investment, we urge youto take responsibility for keeping yourmotorcycle well maintained. Scheduledservice is a must, of course. But it’s just asimportant to observe the break-inguidelines, and perform all pre-ride andother periodic checks detailed in thismanual.
We also recommend that you read thisowner’s manual before you ride. It’s fullof facts, instructions, safety information,and helpful tips. To make it easy to use,the manual contains a detailed list oftopics at the beginning of each section,and both an in-depth table of contents andan index at the back of the book.
As you read this manual, you will findinformation that is preceded by a
symbol. This information isintended to help you avoid damage to yourHonda, other property, or the environment.
05/06/09 15:46:22 31MBZ610_003
Introduction
Introduction
WARNING:
Read the Warranties Booklet (page )thoroughly so you understand thecoverages that protect your new Hondaand are aware of your rights andresponsibilities.
If you have any questions, or if you everneed special service or repairs, rememberthat your Honda dealer knows yourmotorcycle best and is dedicated to yourcomplete satisfaction.
Please report any change of address orownership to your Honda dealer so wewill be able to contact you concerningimportant production information.
This product contains oremits chemicals known to the State ofCalifornia to cause cancer and birthdefects or other reproductive harm.
California Proposition 65 Warning
You may also want to visit our website atwww.honda.com.
Happy riding!
233
05/06/09 15:46:28 31MBZ610_004
A Few Words About Safety
Safety Messages
Safety Labels
Safety MessagesDANGER, WARNING, CAUTION
Your safety, and the safety of others, is very important. And operating this motorcycle safelyis an important responsibility.
To help you make informed decisions about safety, we have provided operating proceduresand other information on labels and in this manual. This information alerts you to potentialhazards that could hurt you or others.
Of course, it is not practical or possible to warn you about all hazards associated withoperating or maintaining a motorcycle. You must use your own good judgment.
You will find important safety information in a variety of forms, including:
–– on the motorcycle.
–– preceded by a safety alert symbol and one of three signal words:or .
These signal words mean:
05/06/09 15:46:32 31MBZ610_005
You WILL be KILLED or SERIOUSLY HURT if youdon’t follow instructions.
You CAN be KILLED or SERIOUSLY HURT if you don’tfollow instructions.
You CAN be HURT if you don’t follow instructions.
A Few Words About Safety
Safety Messages
Safety Headings
Safety Section
Instructions
–– such as Important Safety Reminders or Important Safety Precautions.
–– such as Motorcycle Safety.
–– how to use this motorcycle correctly and safely.
This entire manual is filled with important safety information –– please read it carefully.
05/06/09 15:46:37 31MBZ610_006
Contents
Contents
..............................Motorcycle Safety .
....................Instruments & Controls .
.....................................Before Riding .
................Basic Operation & Riding .
1
9
47
59
These pages give an overview of thecontents of your owner’s manual. The firstpage of each section lists the topicscovered in that section.
The importance of wearing a helmetand other protective gear, how to makesure you and your motorcycle are readyto ride, and important information aboutloading.
Important safety information youshould know, plus a look at the safety-related labels on your motorcycle.
The location and function of indicators,gauges, and controls on yourmotorcycle and operating instructionsfor various controls and features.
How to start and stop the engine, shiftgears, and brake. Also, ridingprecautions and important informationabout riding with a passenger or cargo.
05/06/09 15:46:45 31MBZ610_007
Contents
Contents
........‘‘Reporting Safety Defects’’ .
Quick Reference
......................Servicing Your Honda .
.......Taking Care of the Unexpected .
.....................Consumer Information .
..............................Table of Contents .
....................................................Index .
......................................................Tips .
......................Technical Information .77
169
177
229
207
240
238
244
Why your motorcycle needs regularmaintenance, what you need to knowbefore servicing your Honda, an ownermaintenance schedule, and instructionsfor specific maintenance andadjustment items.
How to store and transport yourmotorcycle and how to be anenvironmentally-responsible rider.
What to do if you have a flat tire, yourengine won’t start, etc.
ID numbers, technical specifications,and other technical facts.
Information on warranties, emissioncontrols, how to get Honda servicemanuals, and...
Sequential listing of topics in thisowner’s manual.
Handy facts about fuel, engine oil, tiresizes, and air pressures.
05/06/09 15:46:56 31MBZ610_008
05/06/09 15:46:58 31MBZ610_009
1
Motorcycle Safety
Motorcycle Safety
This section presents some of the mostimportant information andrecommendations to help you ride yourmotorcycle safely. Please take a fewmoments to read these pages. This sectionalso includes information about thelocation of safety labels on yourmotorcycle.
.................Important Safety Information . 2..................Accessories & Modifications . 5
...........................................Safety Labels . 7
05/06/09 15:47:01 31MBZ610_010
-
2
Important Safety Information
Motorcycle Safety
Always Wear a HelmetYour motorcycle can provide many yearsof service and pleasure if you takeresponsibility for your own safety andunderstand the challenges you can meetwhile riding.
There is much that you can do to protectyourself when you ride. You’ll find manyhelpful recommendations throughout thismanual. The following are a few that weconsider most important.
It’s a proven fact: helmets significantlyreduce the number and severity of headinjuries. So always wear an approvedmotorcycle helmet and make sure yourpassenger does the same. We alsorecommend that you wear eye protection,sturdy boots, gloves, and other protectivegear (page ).48
05/06/09 15:47:05 31MBZ610_011
3
Important Safety Information
Motorcycle Safety
Take Time to Learn & Practice Ride Defensively
You andYour Motorcycle: Riding Tips andPractice Guide,
Even if you have ridden other motorcycles,take time to become familiar with howthis motorcycle works and handles.Practice in a safe area until you build yourskills and get accustomed to themotorcycle’s size and weight.
Because many accidents involveinexperienced or untrained riders, we urgeall riders to take a certified courseapproved by the Motorcycle SafetyFoundation (MSF). See page .
The most frequent motorcycle collisionhappens when a car turns left in front of amotorcycle. Another common situation isa car moving suddenly into your lane.
Always pay attention to other vehiclesaround you, and do not assume that otherdrivers see you. Be prepared to stopquickly or make an evasive maneuver. Forother riding tips, see the booklet,
which came with yournew motorcycle (USA only).
50
05/06/09 15:47:10 31MBZ610_012
4
Important Safety Information
Motorcycle Safety
Don’t Drink and Ride
Keep Your Honda in Safe Condition
Make Yourself Easy to See
Ride within Your Limits
Alcohol and riding don’t mix. Even onedrink can reduce your ability to respond tochanging conditions, and your reactiontime gets worse with every additionaldrink. So don’t drink and ride, and don’tlet your friends drink and ride either.
It’s important to keep your motorcycleproperly maintained and in safe ridingcondition. To help avoid problems, inspectyour motorcycle before every ride andperform all recommended maintenance.Never exceed load limits (page ), anddo not modify your motorcycle (page )or install accessories that would makeyour motorcycle unsafe (page ).
Some drivers do not see motorcyclesbecause they are not looking for them. Tomake yourself more visible, wear brightreflective clothing, position yourself soother drivers can see you, signal beforeturning or changing lanes, and use yourhorn when it will help others notice you.
Pushing limits is another major cause ofmotorcycle accidents. Never ride beyondyour personal abilities or faster thanconditions warrant. Remember thatalcohol, drugs, fatigue, and inattention cansignificantly reduce your ability to makegood judgments and ride safely.
556
5
05/06/09 15:47:15 31MBZ610_013
Improper accessories ormodifications can cause a crash inwhich you can be seriously hurt orkilled.
Follow all instructions in thisowner’s manual regardingaccessories and modifications.
5
Accessories
Accessories & Modifications
Motorcycle Safety
Modifying your motorcycle or using non-Honda accessories can make yourmotorcycle unsafe. Before you considermaking any modifications or adding anaccessory, be sure to read the followinginformation.
We strongly recommend that you use onlygenuine Honda accessories that have beenspecifically designed and tested for yourmotorcycle. Because Honda cannot test allother accessories, you must be personallyresponsible for proper selection,installation, and use of non-Hondaaccessories.Check with your Honda dealer forassistance and always follow theseguidelines:
Make sure the accessory does notobscure any lights, reduce groundclearance and lean angle, limitsuspension travel or steering travel, alteryour riding position, or interfere withoperating any controls.
05/06/09 15:47:20 31MBZ610_014
6
Modifications
Accessories & Modifications
Motorcycle Safety
We strongly advise you not to remove anyoriginal equipment or modify yourmotorcycle in any way that would changeits design or operation. Such changescould seriously impair your motorcycle’shandling, stability, and braking, making itunsafe to ride.
Removing or modifying your lights,exhaust system, emission control system,or other equipment can also make yourmotorcycle illegal.
Do not install any fairing or windshieldunless it was designed and tested byHonda for your motorcycle. Somefairings or windshields, even smallerones, can cause unstable handling ofyour motorcycle. This is especially trueif the fairing or windshield is poorlydesigned or improperly mounted.Do not add any electrical equipmentthat will exceed the motorcycle’selectrical system capacity (page ).A blown fuse can cause a loss of lightsor engine power (page ).Do not pull a trailer or sidecar with yourmotorcycle. This motorcycle was notdesigned for these attachments, andtheir use can seriously impair yourmotorcycle’s handling.
199
215
05/06/09 15:47:26 31MBZ610_015
7
Safety Labels
Motorcycle Safety
Safety labels on your motorcycle either warn you of potential hazards that could causeserious injury or they provide important safety information. Read these labels carefully anddon’t remove them.
If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.
05/06/09 15:47:34 31MBZ610_016
〈 〉
〈 〉
For USA
For Canada
8
Safety Labels
Motorcycle Safety
05/06/09 15:47:47 31MBZ610_017
9
Instruments & Controls
Instruments & Controls
This section shows the location of allgauges, indicators, and controls you wouldnormally use before or while riding yourmotorcycle.
The items listed on this page are describedin this section. Instructions for othercomponents are presented in other sectionsof this manual where they will be mostuseful.
..........Operation Component Locations . 11..............Gauges, Indicators & Displays . 14
......................Multi-function Display . 22
..Malfunction Indicator Lamp (MIL) . 23Low Oil Pressure Indicator and
..Malfunction Indicator Lamp (MIL) . 24......................................Speedometer . 25
Changing the Speed and Mileage....................................................Unit . 25
Odometer/Tripmeter A & B/............Mileage Countdown Display . 26
...........................................Odometer . 27...............................Tripmeter A & B . 27
..........................Mileage Countdown . 28.....Digital Clock/Stopwatch Display . 31
.....................................Digital Clock . 32..........................................Stopwatch . 35.........................................Fuel Gauge . 37
..............Coolant Temperature Meter . 39
High Coolant Temperature Indicator and
05/06/09 15:47:52 31MBZ610_018
10
Instruments & Controls
Instruments & Controls
...............................Controls & Features . 41......................................Choke Lever . 41
..................................Ignition Switch . 42........................................Start Button . 43
...........................Engine Stop Switch . 43................Headlight Dimmer Switch . 44
............................Turn Signal Switch . 44.......................................Horn Button . 45.....................................Select Switch . 45......................................Reset Switch . 46
05/06/09 15:47:55 31MBZ610_019
turn signal switch
clutch lever
start button
ignition switch
horn button
front brake lever
throttle grip
choke lever
engine stopswitchheadlight dimmer
switch
11
Operation Component Locations
Instruments & Controls
05/06/09 15:47:59 31MBZ610_020
rear brake pedal
storage compartmentfor U-shaped lock
12 Instruments & Controls
Operation Component Locations
05/06/09 15:48:03 31MBZ610_021
helmet holder
seat lock
shift lever
13Instruments & Controls
Operation Component Locations
05/06/09 15:48:09 31MBZ610_022
(2) (3) (5) (6)
(11)(10) (8)
(4)(1)
(9)
(7)
14
Gauges, Indicators & Displays
Instruments & Controls
The gauges, indicators and displays onyour motorcycle keep you informed, alertyou to possible problems, and make yourriding safer and more enjoyable. Refer tothe gauges, indicators and displaysfrequently. Their functions are describedon the following pages.
(1) left turn signal indicator(2) malfunction indicator lamp (MIL)(3) neutral indicator(4) high beam indicator(5) right turn signal indicator(6) tachometer(7) tachometer red zone(8) coolant temperature meter(9) multi-function display
(10) reset switch(11) select switch
05/06/09 15:48:15 31MBZ610_023
15Instruments & Controls
Gauges, Indicators & Displays
Meter Check.
Lamp Check.
Lamp Check If one of these indicators does not comeon when it should, have your Honda dealercheck for problems.
Meter Check
The tachometer needle will swing to theend of the red zone once when you turnthe ignition switch ON.
The meter is identified in the table on pagewith the words:
If the tachometer needle does not swing tothe end of the red zone when it should,have your Honda dealer check forproblems.
The malfunction indicator lamp (MIL)comes on when you turn the ignitionswitch ON so you can check that it isworking. The indicator remains on untilafter the engine is started.
When applicable, the high beam andneutral indicators come on when you turnthe ignition switch ON and remain on untilyou select the low beam or shift out ofneutral.
These indicators are identified in the tableon page with the words:17
18
05/06/09 15:48:22 31MBZ610_024
-
(3)
(1) (2)
(1) multi-function display(2) coolant temperature meter(3) speedometer
16
Gauges, Indicators & Displays
Instruments & Controls
DisplayCheck.
Display Check
When the ignition switch is turned ON, themulti-function display ( ) and coolanttemperature meter ( ) will temporarilyshow the entire digital display. Thereafter,the speedometer ( ) will show from 150mph to 0 mph (from 230 km/h to 0 km/hin km/h) so that you can make sure theliquid crystal display is functioningproperly.
The low oil pressure indicator and fuelgauge flash when you turn the ignitionswitch ON so you can check that they areworking. The low oil pressure indicatorremains on until after the engine is started.
If any part of these displays does not comeon when it should, have your Honda dealercheck for problems.
The displays are identified in the table onpages with the words:
12
3
18 20
05/06/09 15:48:29 31MBZ610_025
--
17
Gauges, Indicators & Displays
Instruments & Controls
Lamp Check.
Lamp Check.
left turn signal indicator(amber)
Flashes when the left turn signal operates.
malfunction indicatorlamp (MIL) (red)
Lights when coolant is over the specifiedtemperature, and/or engine oil pressure is belownormal operating range. If the indicator lights, pullsafely to the side of the road. (pages ).
See pages for instructionsand cautions.
neutral indicator (green)
high beam indicator(blue)
1
2
3
4
Lights when the transmission is in neutral.
Lights when the headlight is on high beam.
196 19823 24
05/06/09 15:48:36 31MBZ610_026
18
Gauges, Indicators & Displays
Instruments & Controls
Meter Check.
Display Check.
right turn signalindicator (amber)tachometer
tachometer red zone
coolant temperaturemeter
Flashes when the right turn signal operates.
Shows engine speed in revolutions per minute (rpm).
Shows excessive engine rpm range (indicated fromthe beginning of the tachometer red zone) in whichoperation may damage the engine. Do not let thetachometer needle enter the red zone.Shows engine coolant temperature digitally (page
).USA: Fahrenheit (°F), Canada: Centigrade (°C).
5
6
7
839
05/06/09 15:48:43 31MBZ610_027
-
19
Gauges, Indicators & Displays
Instruments & Controls
Display Check.multi-function display The display includes the following functions:
low oil pressure indicator/high coolant temperatureindicator
Flashes when the malfunction indicator lights tonotify that there is abnormality in engine oil pressureand/or coolant temperature.See pages .
speedometer
odometertripmeter A & B
Shows riding speed in miles or kilometers per hour(page ).Shows the total miles or kilometers ridden (page ).Shows the number of miles or kilometers riddensince you last reset the meter. The tripmeter has twosub modes, ‘‘A’’ and ‘‘B.’’ To zero (0) the tripmeter,press and hold the reset switch (page ).
mileage countdown Shows subtraction mileage (page ).digital clock Shows hour and minute (page ).
Shows stopwatch (page ).stopwatch
9
fuel gauge Shows approximate fuel supply available (page ).
2728
3235
2527
2423
37
05/06/09 15:48:57 31MBZ610_028
20
Gauges, Indicators & Displays
Instruments & Controls
reset switch10 Use this switch for the following purposes.To switch between the digital clock andstopwatch display (page ).To reset the tripmeter (page ) and stopwatch(page ).To change the speed and mileage units for thespeedometer/odometer/tripmeter/mileagecountdown (page ).To set the mileage countdown (page ) anddigital clock (page ).
3127
35
25
3228
05/06/09 15:49:04 31MBZ610_029
21
Gauges, Indicators & Displays
Instruments & Controls
Use this switch for the following purposes.To switch between the odometer, two tripmeter(A & B) and mileage countdown display (page
).To change the speed and mileage units for thespeedometer/odometer/tripmeter/mileagecountdown (page ).To set the mileage countdown (page ) anddigital clock (page ).To start and stop the stopwatch (page ).
11 select switch
26
2528
3235
05/06/09 15:49:11 31MBZ610_030
(1) (2) (3) (6)
(4)
(5)(7)
(1) multi-function display(2) high coolant temperature indicator(3) low oil pressure indicator(4) speedometer(5) odometer/tripmeter/mileage
countdown display(6) digital clock/stopwatch display(7) fuel gauge
22
Multi-function Display
Gauges, Indicators & Displays
Instruments & Controls
The multi-function display ( ) includesthe following functions:
high coolant temperature indicatorlow oil pressure indicatorspeedometerodometer/tripmeter/mileage countdowndigital clock/stopwatchfuel gauge
The digital clock will reset if the battery isdisconnected.
1
05/06/09 15:49:17 31MBZ610_031
-
(1) high coolant temperature indicator(2) malfunction indicator lamp (MIL)
(2)
(1)
23
High Coolant Temperature Indicatorand Malfunction Indicator Lamp(MIL)
Gauges, Indicators & Displays
Instruments & Controls
Continuing to ride with an overheatedengine can cause serious engine damage.
The high coolant temperature indicator( ) flashes and the malfunction indicatorlamp (MIL) ( ) lights when the coolanttemperature reaches 251°F (122°C). At thesame time, the numbers in the coolanttemperature meter display start flashing.If this occurs, stop the engine and checkthe reserve tank coolant level. Read pages
and do not ride themotorcycle until the problem has beencorrected.
116113
12
05/06/09 15:49:22 31MBZ610_032
(2)
(1)
(1) low oil pressure indicator(2) malfunction indicator lamp (MIL)
24
Gauges, Indicators & Displays
Instruments & Controls
Low Oil Pressure Indicator andMalfunction Indicator Lamp (MIL)
The low oil pressure indicator ( ) flashesand the malfunction indicator lamp (MIL)( ) lights when engine oil pressure is lowenough to cause engine damage.
The low oil pressure indicator should alsoflash and the malfunction indicator lamp(MIL) should also go on when the ignitionswitch is turned ON. The malfunctionindicator lamp (MIL) stays on and the lowoil pressure indicator keeps flashing untilafter the engine is started.
If the low oil pressure indicator flashesand the malfunction indicator lamp goeson, pull safely to the side of the road.See page for instructions and cautions.
1198
2
05/06/09 15:49:28 31MBZ610_033
(1)
(2)
(3)
(1) speedometer(2) select switch(3) reset switch
25
Speedometer
Changing the Speed andMileage Unit
Gauges, Indicators & Displays
Instruments & Controls
The speedometer ( ) shows riding speedin miles or kilometers per hour.
The speedometer displays both ‘‘mph’’and ‘‘km/h.’’The odometer/tripmeter/mileagecountdown displays both ‘‘mile’’ and‘‘km.’’
To select ‘‘mph’’/‘‘mile’’ and‘‘km/h’’/‘‘km’’, press and hold both theselect switch ( ) and reset switch ( ) formore than 2 seconds with the displays inthe odometer mode and digital clock mode.
3
1
2
05/06/09 15:49:35 31MBZ610_034
(1) select switch(2) odometer(3) tripmeter A(4) tripmeter B(5) mileage countdown
(1)(2)
(3)
(4)
(5)
26
Odometer/Tripmeter A & B/Mileage Countdown Display
Gauges, Indicators & Displays
Instruments & Controls
The display has three functions:odometer, tripmeter and mileagecountdown.
Press the select switch ( ) to select‘‘TOTAL’’ (odometer) ( ), ‘‘TRIP A’’(tripmeter A) ( ), ‘‘TRIP B’’ (tripmeterB) ( ) and ‘‘TRIP’’ (mileage countdown)( ) mode.
12
34
5
05/06/09 15:49:43 31MBZ610_035
(1) odometer(2) tripmeter A(3) tripmeter B(4) reset switch
(1)
(2)
(3)
(4)
27
Odometer
Tripmeter A & B
Gauges, Indicators & Displays
Instruments & Controls
The odometer ( ) shows the total miles orkilometers ridden.
The tripmeter shows number of miles orkilometers ridden since you last reset themeter.
The tripmeter has two sub modes, A ( )and B ( ).
To reset the tripmeter, press and hold thereset switch ( ) for more than 2 secondswhen the display in the ‘‘TRIP A’’ or‘‘TRIP B.’’
2
1
3
4
05/06/09 15:49:51 31MBZ610_036
(1)
(1) mileage countdown
(2)
(2) reset switch
28
Mileage Countdown
Gauges, Indicators & Displays
Instruments & Controls
Mileage countdown ( ) shows subtractionmileage.
In this mode, the mileage will besubtracted from the preset figure. Whenthe mileage exceeds the preset figure, thenumeric will flash.
How to Set Distance:Turn the ignition switch ON.
Press and hold the reset switch ( ) formore than 2 seconds.
Display will change to the setdistance mode or reset to the initialsetting. See following Example page.
Select the mileage countdown (page) and digital clock (page )
displays.1
1.2.
3.
26 31
2
05/06/09 15:50:00 31MBZ610_037
(2) reset switch
(2)
Change to the set distance mode.Reset to the initial setting.
29
Gauges, Indicators & Displays
Instruments & Controls
ExampleIf you set the trip mileage, then resetbefore completing the set distance, thesubtraction trip mode will reset to theinitial setting.
If you set the subtraction trip mode anddo not travel, you will have to re-enterthe trip distance.
(cont’d)
05/06/09 15:50:08 31MBZ610_038
-
(3) select switch
(3)
30
Gauges, Indicators & Displays
Instruments & Controls
The preset figure is displayed and thethird digit will be flashing.To set the third digit, press the resetswitch until the desired third digitappears.
Quick setting press and hold thereset switch until the desired thirddigit appears.
Press the select switch ( ) when thedisplay reaches the desired figure.The second digit will be flashing.
If the ignition switch is turned OFF or nooperation is performed for 30 secondsduring the adjustment mode, the set digitswill reset.
Repeat steps 5 and 6 for the second andfirst digits.
4.
5.
6. 3
7.
05/06/09 15:50:18 31MBZ610_039
(1)
(1) reset switch(2) digital clock(3) stopwatch
(2)
(3)
31
Digital Clock/Stopwatch Display
Gauges, Indicators & Displays
Instruments & Controls
The display has two functions:digital clock and stopwatch.
Press the reset switch ( ) to select digitalclock ( ) and stopwatch ( ) mode.
132
05/06/09 15:50:24 31MBZ610_040
(1)(2)
(1) select switch(2) digital clock mode
32
Digital Clock
Gauges, Indicators & Displays
Instruments & Controls
The digital clock will show hours andminutes up to 12:59 with ‘‘AM’’ and‘‘PM’’.To adjust the time, proceed as follows:
Turn the ignition switch ON.Press and hold the select switch ( ) formore than 2 seconds in the digital clockmode ( ). The clock will be set in theadjust mode with the hour displayflashing.
1.2. 1
2
05/06/09 15:50:31 31MBZ610_041
-Quick setting push and hold thereset switch until the desired hourappears.
(3)
(3) reset switch
33
Gauges, Indicators & Displays
Instruments & Controls
To set the hour, press the reset switchuntil the desired hour and AM/PM aredisplayed.
Press the select switch. The minutedisplay will start flashing.
(cont’d)
3. 4.
05/06/09 15:50:40 31MBZ610_042
-
34
Gauges, Indicators & Displays
Instruments & Controls
To set the minute, press the reset switchuntil the desired minute is displayed.The minute display will return to ‘‘00’’when ‘‘60’’ is reached withoutaffecting the hour display.
To end the adjustment, press the selectswitch or turn the ignition switch OFF.The display will stop flashingautomatically and the adjustment willbe cancelled if the switch is not pressedfor about 30 seconds.
The clock will be reset AM 1:00 if thebattery is disconnected.
Quick setting push and hold thereset switch until the desired minuteappears.
5. 6.
05/06/09 15:50:46 31MBZ610_043
(2)(1)
START
PAUSE
RESUME
(1) stopwatch(2) select switch
35
Stopwatch
Gauges, Indicators & Displays
Instruments & Controls
The stopwatch ( ) will count hours andminutes.
Stopwatch Measurement Range:After measuring 12 hours, 59 minutes, itreturns to 0 hours, 0 minutes and willcontinue counting.
How to Measure Time:Select the stopwatch mode (page ).To measure, press the select switch ( ).While measuring, press the selectswitch to pause and press it again toresume.
1.2.
1
312
05/06/09 15:50:56 31MBZ610_044
PAUSE
(3) reset switch
(3)
RESET
36
Gauges, Indicators & Displays
Instruments & Controls
Stopwatch Reset:Press and hold the reset switch ( ) formore than 2 seconds when the stopwatchis paused.
3
05/06/09 15:51:01 31MBZ610_045
4.49 US gal (17.0 )
0.79 US gal (3.0 )
(1) (2)
(3)
(1) fuel gauge(2) segment F(3) segment E
37
Fuel Gauge
Gauges, Indicators & Displays
Instruments & Controls
The fuel gauge ( ) shows the approximatefuel supply available in a graduateddisplay. When all segments up to segmentF ( ) are lit, the fuel tank capacityincluding reserve is:
When segment E ( ) passes, fuel gaugewill be displayed as shown in theillustration. You should refill the tank assoon as possible.The amount of fuel available when thedisplaying starts is approximately:
1
2
3
05/06/09 15:51:07 31MBZ610_046
38
Gauges, Indicators & Displays
Instruments & Controls
Fuel Gauge Failure IndicationWhen the fuel system has an error, thefuel gauge indicators will be displayed asshown in the illustration. If this occurs, seeyour Honda dealer as soon as possible.
05/06/09 15:51:14 31MBZ610_047
--
〈 〉
〈 〉
(1)For Canada
For USA
(1) coolant temperature meter
39
Coolant Temperature Meter
Gauges, Indicators & Displays
Instruments & Controls
The coolant temperature meter ( ) showsthe coolant temperature digitally.
USA : Fahrenheit (°F),Canada : Centigrade (°C).
Temperature Meter
1
Below94 °F (34 °C)Between95 °F 270 °F(35 °C 132 °C)Above270 °F (132 °C)
‘‘--’’ is displayed
Actual coolanttemperature isdisplayed.The meter remains‘‘270 °F (132 °C)’’
05/06/09 15:51:21 31MBZ610_048
-
〈 〉
〈 〉
For USA
For Canada
(2)
(3)
(2) high coolant temperature indicator(3) malfunction indicator lamp (MIL)
40
Gauges, Indicators & Displays
Instruments & Controls
Continuing to ride with an overheatedengine can cause serious engine damage.
Overheating Message:When the coolant temperature reaches251°F (122°C), the numbers in thetemperature meter start flashing. At thesame time, the high coolant temperatureindicator ( ) flashes and the malfunctionindicator lamp (MIL) ( ) goes on.If this occurs, stop the engine and checkthe reserve tank coolant level. Read pages
and do not ride the motorcycleuntil the problem has been corrected.
23
116113
05/06/09 15:51:27 31MBZ610_049
LEFT FRONT
(1) choke lever (A) fully on(B) fully off
(1)
((BB))
((AA))
41
Choke Lever
Controls & Features
Instruments & Controls
The choke lever may be used whenstarting the engine. See page .62
05/06/09 15:51:32 31MBZ610_050
ONOFF
Electrical circuits on.No electricalcircuits function.No electrical circuitsfunction. Locks thesteering head.
LOCK(steeringlock)
(1)FRONT
(1) ignition switch
ONOFF
LOCK
Key Position Function
42
Ignition Switch
Controls & Features
Instruments & Controls
The ignition switch is used for starting andstopping the engine (page ) and to lockthe steering for theft prevention (page ).Insert the key and turn it to the right forthe ON position. Push down on the keyand turn it to the left to the LOCK(steering lock) position.
To unlock the steering lock, insert andpush down on the key and turn it to theright to the OFF position.
6573
05/06/09 15:51:42 31MBZ610_051
(1)
RIGHT HANDLEBAR
(2)
OFFRUN
(1) start button(2) engine stop switch
43
Start Button Engine Stop Switch
Controls & Features
Instruments & Controls
Starting Procedure,
When the start button is pushed, the startermotor will crank the engine; the headlightwill automatically go out, but the taillightwill stay on.
The starter motor will not operate if theengine stop switch is in the OFF positionwhen the start button is pushed.
The start button ( ) is used for starting theengine. Pushing the button in starts theengine. See page .
The engine stop switch ( ) is used to stopthe engine in an emergency. To operate,push the switch to the OFF position. Theswitch must be in the RUN position tostart the engine, and it should normallyremain in the RUN position even when theengine is OFF.
1
2
62
05/06/09 15:51:49 31MBZ610_052
(1)
(2)
HILO
(3)
(1) headlight dimmer switch
(2) turn signal switch(3) horn button
44
Turn Signal Switch
Headlight Dimmer Switch
Controls & Features
Instruments & Controls
If your motorcycle is stopped with theignition switch ON and the engine stopswitch OFF, the headlight and taillightwill remain on, resulting in batterydischarge.
The turn signal switch ( ) is used to signala turn or a lane change. To operate, movethe switch all the way in the properdirection and release it. The appropriateturn signal lights will start blinking. Tocancel the light, push the switch in.The headlight dimmer switch ( ) is used
to change between the high and low beamsof the headlight. To operate, turn theswitch to HI for high beam, LO for lowbeam.
1
2
05/06/09 15:51:55 31MBZ610_053
45
Horn Button
Select Switch
Controls & Features
Instruments & Controls
The horn is used to alert other motorists.To operate, push the horn button ( ).
The select switch is used to switchbetween the odometer, the two tripmeter(A & B) and mileage countdown displays.To operate, press the switch (page ).
The select switch is also used to changethe speed and mileage units for thespeedometer/odometer/tripmeter/mileagecountdown. To change the unit, press andhold the switch (page ).
The select switch is also used to set themileage countdown (page ) and digitalclock (page ).
The select switch is also used to start andstop the stopwatch. To start and stop, pressthe switch (page ).
3
25
2832
35
26
05/06/09 15:52:02 31MBZ610_054
46
Reset Switch
Controls & Features
Instruments & Controls
The reset switch is also used to set themileage countdown (page ) and digitalclock (page ).
The reset switch is used to switch betweenthe digital clock and stopwatch displays.To operate, press the switch (page ).
The reset switch is also used to reset thetripmeter (page ) and stopwatch (page
).
The reset switch is also used to change thespeed and mileage units for thespeedometer/odometer/tripmeter/mileagecountdown. To change the unit, press andhold the switch (page ).
2832
2735
31
25
05/06/09 15:52:08 31MBZ610_055
?
?
47
Before Riding
Before Riding
Before each ride, you need to make sureyou and your Honda are both ready to ride.To help get you prepared, this sectiondiscusses how to evaluate your ridingreadiness, what items you should check onyour motorcycle, and adjustments to makefor your comfort, convenience, or safety.This section also includes importantinformation about loading.
For information about adjusting thesuspension on your Honda, see page .
.....................Are You Ready to Ride . 48.............................Protective Apparel . 48
...................................Rider Training . 50...Is Your Motorcycle Ready to Ride . 51
............................Pre-ride Inspection . 51......................Load Limit & Guidelines . 54
..............................................Loading . 54.......................................Load Limits . 55
...........................Loading Guidelines . 55................Luggage Tie-Down Hooks . 57
131
05/06/09 15:52:12 31MBZ610_056
48
Protective Apparel
Are You Ready to Ride?
Before Riding
Before you ride your motorcycle for thefirst time, we urge you to:
Read this owner’s manual.Make sure you understand all the safetymessages.Know how to operate all the controls.
You feel well and are in good physicaland mental condition.
Before each ride, be sure:
If you must carry an extra helmet whileriding, use a commercially-availableelastic cord, strap, or net to secure thehelmet to the seat.
For your safety, we strongly recommendthat you always wear an approvedmotorcycle helmet, eye protection, boots,gloves, long pants, and a long-sleevedshirt or jacket whenever you ride.Although complete protection is notpossible, wearing proper gear can reducethe chance of injury when you ride.Following are suggestions to help youchoose the proper gear.
You are wearing an approvedmotorcycle helmet (with chin straptightened securely), eye protection, andother protective clothing.
Make sure your passenger is ready to ride,too, and is wearing proper gear including ahelmet.
You don’t have any alcohol or drugs inyour system.
05/06/09 15:52:20 31MBZ610_057
Not wearing a helmet increasesthe chance of serious injury ordeath in a crash.
Be sure you and your passengeralways wear a helmet, eyeprotection, and other protectiveapparel when you ride.
49
Are You Ready to Ride?
Before Riding
(cont’d)
Helmets and Eye ProtectionYour helmet is your most important pieceof riding gear because it offers the bestprotection against head injuries. A helmetshould fit your head comfortably andsecurely. A bright-colored helmet andreflective strips can make you morenoticeable in traffic.
An open-face helmet offers someprotection, but a full-face helmet offersmore. Regardless of the style, look for aDOT (Department of Transportation)sticker in any helmet you buy (USA only).Always wear a face shield or goggles toprotect your eyes and help your vision.
Leather gloves to help protect yourhands.
Sturdy boots with non-slip soles to helpprotect your feet and ankles.
In addition to a helmet and eye protection,we also recommend:
Additional Riding Gear
05/06/09 15:52:28 31MBZ610_058
50
Rider Training
Are You Ready to Ride?
Before Riding
Riding Tips
A motorcycle riding suit or jacket forcomfort as well as protection.Bright-colored and reflective clothingcan help make you more noticeable intraffic. Avoid loose clothes that couldget caught on any part of yourmotorcycle.
Developing your riding skills is an on-going process. Even if you have riddenother motorcycles, take time to becomefamiliar with how this motorcycle worksand handles. Practice riding themotorcycle in a safe area to build yourskills. Do not ride in traffic until you getaccustomed to the motorcycle’s controls,and feel comfortable with its size andweight.
We urge all riders to take a certifiedcourse approved by the Motorcycle SafetyFoundation (MSF). New riders shouldstart with the basic course, and evenexperienced riders will find the advancedcourse beneficial. For information aboutthe MSF training course nearest you, callthe national toll-free number: (800) 446-9227.
Other riding tips can be found in thebooklet that came with your
motorcycle (USA only).
05/06/09 15:52:33 31MBZ610_059
Improperly maintaining thismotorcycle or failing to correct aproblem before riding can cause acrash in which you can beseriously hurt or killed.
Always perform a pre-rideinspection before every ride andcorrect any problems.
51
Pre-ride Inspection
Before Riding
Is Your Motorcycle Ready to Ride?
Tires&
Wheels
Chain
Before each ride, it’s important to inspectyour motorcycle and make sure anyproblem you find is corrected. A pre-rideinspection is a must, not only for safety,but because having a breakdown, or evena flat tire, can be a major inconvenience.
Check the following items before you geton the motorcycle:
(cont’d)
Look at the tires. If a tireappears low, use an air pressuregauge to check its pressure. Alsolook for signs of excessive wear(page ) or damage to thetires and wheels.
Check the condition of the chain.Adjust slack and lubricate asneeded (page ).
142
149
05/06/09 15:52:40 31MBZ610_060
52
Is Your Motorcycle Ready to Ride?
Before Riding
Leaks,LooseParts
Lights
Load Limits
Cargo
Adjustments
Walk around yourmotorcycle and look foranything that appearsunusual, such as a leak orloose cable.
Make sure the headlight,brakelight, taillight, andturn signals are workingproperly.
If you are carrying a passenger or cargo,also check the following:
Make sure you do notexceed the load limits(page ).
Check that all cargo issecure.
Adjust the rear suspension(page ) according toyour load.
55
132
05/06/09 15:52:49 31MBZ610_061
53
Is Your Motorcycle Ready to Ride?
Before Riding
Periodic MaintenanceThrottle
Brakes
Indicators
If you haven’t ridden the motorcycle inover a week, you should also check otheritems, such as the oil level and other fluids.See (page ).Periodic maintenance should also be doneat least once a month, no matter how oftenyou ride.
Remember, be sure to take care of anyproblem you find, or have your Hondadealer correct it before you ride.
Check these items after you get on themotorcycle:
Rotate the throttle to checkit moves smoothly withoutbinding.
Pull the brake lever andpress on the brake pedal tocheck that they operatenormally.
Turn the ignition on andcheck for normal operationof the indicators (page ).14
84
05/06/09 15:52:57 31MBZ610_062
Overloading or improper loadingcan cause a crash and you can beseriously hurt or killed.
Follow all load limits and otherloading guidelines in this manual.
54
Loading
Load Limits & Guidelines
Before Riding
Your motorcycle has been designed tocarry you and one passenger. When youcarry a passenger, you may feel somedifference during acceleration and braking.But so long as you keep your motorcyclewell-maintained, with good tires andbrakes, you can safely carry loads withinthe given limits and guidelines.
However, exceeding the weight limit orcarrying an unbalanced load can seriouslyimpair your motorcycle’s handling,braking, and stability. Non-Hondaaccessories, improper modifications, andpoor maintenance can also reduce yoursafety margin.
How much weight you put on yourmotorcycle, and how you load it, areimportant to your safety. Anytime youride with a passenger or cargo, you shouldbe aware of the following information.
05/06/09 15:53:02 31MBZ610_063
384 lbs (174 kg)392 lbs (178 kg)
60 lbs (27 kg)
55
Loading GuidelinesLoad Limits
Load Limits & Guidelines
Before Riding
maximum weight capacity:
maximum cargo weight:
Your motorcycle is primarily intended fortransporting you and a passenger. Youmay wish to secure a jacket or other smallitems to the seat when you are not ridingwith a passenger.
If you wish to carry more cargo, checkwith your Honda dealer for advice, and besure to read the information regardingaccessories on page .
Following are the load limits for yourmotorcycle:
includes the weight of the rider,passenger, all cargo, and all accessories.
Improperly loading your motorcycle canaffect its stability and handling. Even ifyour motorcycle is properly loaded, youshould ride at reduced speeds and neverexceed 80 mph (130 km/h) when carryingcargo.
The weight of added accessories willreduce the maximum cargo weight youcan carry.
5
(Canada only)
05/06/09 15:53:12 31MBZ610_064
56
Load Limits & Guidelines
Before Riding
Follow these guidelines whenever youcarry a passenger or cargo:
If you change your normal load, youmay need to adjust the rear suspension(page ).To prevent loose items from creating ahazard, make sure that all cargo is tieddown securely before you ride.Place cargo weight as low and close tothe center of your motorcycle aspossible.Balance cargo weight evenly on bothsides.
Check that both tires are properlyinflated (page ).140
132
05/06/09 15:53:17 31MBZ610_065
(1)
(2)
(1) luggage tie-down hooks(2) seat
(1)
SEAT UNDERSIDE
57
Luggage Tie-Down Hooks
Load Limits & Guidelines
Before Riding
Your motorcycle is equipped withretractable luggage tie-down hooks ( ) onthe underside of the seat ( ). To use thehooks, remove the seat and pull the hooksoutward. Install the hooks in the clips andinstall the seat.
Never use the tie-down hooks to tow orlift your motorcycle.
21
05/06/09 15:53:23 31MBZ610_066
58 Before Riding
05/06/09 15:53:25 31MBZ610_067
59
Basic Operation & Riding
Basic Operation & Riding
This section gives basic riding instructions,including how to start and stop yourengine, and how to use the throttle, clutch,and brakes. It also provides importantinformation on riding with a passenger orcargo.
To protect your new engine and enjoyoptimum performance and service life,refer to Break-in Guidelines (page ).
To protect the catalytic converters in yourmotorcycle’s exhaust system, avoidextended idling and the use of leadedgasoline.
........................Safe Riding Precautions . 60............Starting & Stopping the Engine . 61
.........................................Preparation . 61.............................Starting Procedure . 62
..................................Flooded Engine . 64....................How to Stop the Engine . 65
........................................Shifting Gears . 66..................................................Braking . 68...................................................Parking . 70
.........Riding with a Passenger or Cargo . 75218
05/06/09 15:53:30 31MBZ610_068
60
Safe Riding Precautions
Basic Operation & Riding
Motorcycle Saf ety
Bef ore Riding
Before riding your motorcycle for the firsttime, please review thesection beginning on page 1, and the
section beginning on page.
Even if you have ridden other motorcycles,take time to become familiar with howthis motorcycle works and handles.Practice in a safe area until you build yourskills and get accustomed to themotorcycle’s size and weight.
Make sure flammable materials such asdry grass or leaves do not come in contactwith the exhaust system when riding,idling, or parking your motorcycle.
47
05/06/09 15:53:35 31MBZ610_069
61
Preparation
Starting & Stopping the Engine
Basic Operation & Riding
Always follow the proper startingprocedure described below.
For your safety, avoid starting or operatingthe engine in an enclosed area such as agarage. Your motorcycle’s exhaustcontains poisonous carbon monoxide gaswhich can collect rapidly in an enclosedarea and cause illness or death.
Your motorcycle can be started with thetransmission in gear by pulling in theclutch lever before operating the starter.
Your motorcycle is equipped with a sidestand ignition cut-off system. If the sidestand is down––the engine cannot bestarted unless the transmission is in neutral.If the side stand is up––the engine can bestarted in neutral, or in gear with the
clutch lever pulled in. After starting withthe side stand down, the engine will stop ifthe transmission is put in gear beforeraising the side stand.
Before starting, insert the key, turn theignition switch ON, and confirm thefollowing:
The transmission is in NEUTRAL(neutral indicator light ON).The engine stop switch is set to RUN.
The low oil pressure indicator isflashing.
The malfunction indicator lamp (MIL)is ON.
05/06/09 15:53:42 31MBZ610_070
- -
(1)
((BB))
((AA))
(A) fully ON(B) fully OFF
(1) choke lever
62
Starting Procedure
Starting & Stopping the Engine
Basic Operation & Riding
High Air Temperature.To restart a warm engine, follow theprocedure for
Normal Air Temperature10° 35°C (50° 95°F)
The malfunction indicator lamp (MIL) andlow oil pressure indicator should go off afew seconds after the engine starts. If themalfunction indicator lamp (MIL) lightsand the low oil pressure indicator flashesduring operation, stop the engineimmediately and check the engine oil level.
05/06/09 15:53:48 31MBZ610_071
-- 2,500 3,000 rpm2,500 3,000 rpm
63
Starting & Stopping the Engine
Basic Operation & Riding
Normal AirTemperature.
High Air Temperature35°C (95°F) or aboveDo not use the choke.
(cont’d)
Pull the choke lever back all the way tofully ON ( ), if the engine is cold.With the throttle fully closed, operatethe electric starter.
Do not open the throttle when startingthe engine with the choke on. This willlean the mixture, resulting in hardstarting.
About a half minute after the enginestarts, push the choke lever ( ) forwardall the way to fully OFF ( ).If idling is unstable, open the throttleslightly.
Low Air Temperature10°C (50°F) or below
Immediately after the engine starts,operate the choke lever to keep fast idleat:
Follow steps 1-2 under
When engine rpm begins to pick up,operate the choke knob to keep fast idleat:
With the throttle slightly open, press thestart button.
Continue warming up the engine until itruns smoothly and responds to thethrottle when the choke lever is at fullyOFF ( ).
1.
2.
3.
4.
1.2.
1.
2.
A
5.
1B
3.
B
05/06/09 15:53:59 31MBZ610_072
64
Flooded Engine
Starting & Stopping the Engine
Basic Operation & Riding
IfYour Engine Quits or Won’t Start,
Extended use of the choke may impairpiston and cylinder wall lubrication anddamage the engine.
Push the choke lever forward all theway to fully OFF.Open the throttle fully.Press the start button for 5 seconds.If the engine starts, quickly close thethrottle, then open it slightly if idling isunstable.If the engine does not start, wait 10seconds, then follow the normal startingprocedure with the choke OFF.
If the engine still won’t start, refer topage
.
Snapping the throttle or fast idling formore than about 5 minutes at normal airtemperature may cause exhaust pipediscoloration.
If the engine fails to start after repeatedattempts, it may be flooded with excessfuel. To clear a flooded engine:
Leave the engine stop switch set toRUN.
1.
4.5.
2.
3.
179
05/06/09 15:54:09 31MBZ610_073
65
How to Stop the Engine
Starting & Stopping the Engine
Basic Operation & Riding
Normal Engine StopTo stop the engine, shift into neutral andturn the ignition switch OFF.
The engine stop switch should normallyremain in the RUN position even when theengine is OFF.
If your motorcycle is stopped with theengine stop switch OFF and the ignitionswitch ON, the headlight and taillightwill remain on, resulting in batterydischarge.
Emergency Engine StopTo stop the engine in an emergency, usethe engine stop switch. To operate, pressthe switch to the OFF position.
05/06/09 15:54:15 31MBZ610_074
shifting pattern
66
Shifting Gears
Basic Operation & Riding
Learning when to shift gears comes withexperience. Keep the following tips inmind:
Close the throttle and pull the clutchlever in completely before shifting.Improper shifting may damage theengine, transmission, and drive train.Learn to recognize the engagementpoint as you release the clutch lever. Itis at this point the transmission ofpower to the rear wheel resumes.Upshift to a higher gear or reducethrottle before engine rpm (speed) getstoo high. Learn the relationship betweenengine sound and the normal shiftingpoints.
As a general rule, shift while moving ina straight line.
Downshift to a lower gear before youfeel the engine laboring (lugging) atlow rpm.
Your motorcycle has six forward gears ina one-down, five-up shift pattern which iscoordinated with a cable-operated clutchsystem.
05/06/09 15:54:22 31MBZ610_075
67
Shifting Gears
Basic Operation & Riding
Shif ting Up:
Shif ting Down:
Avoid downshifting to help slow yourmotorcycle when engine rpm is near itsallowable maximum (near thetachometer red zone). In this situation,the rev limiter in the engine ignitioncontrol module may not preventexcessive engine speed which coulddamage the engine.To prevent transmission damage, do notcoast or tow the motorcycle for longdistances with the engine off.
Recommended Shift PointsRide in the highest gear that lets theengine run and accelerate smoothly. Thiswill give you good fuel economy andeffective emissions control. Whenchanging gears under normal conditions,use these recommended shift points:
From 1st to 2nd:From 2nd to 3rd:From 3rd to 4th:From 4th to 5th:From 5th to 6th:
12 mph (20 km/h)19 mph (30 km/h)25 mph (40 km/h)31 mph (50 km/h)37 mph (60 km/h)
From 6th to 5th:From 5th to 4th:From 4th to 3rd:
28 mph (45 km/h)22 mph (35 km/h)16 mph (25 km/h)
Pull the clutch lever in when speed dropsbelow 9 mph (15 km/h), when engineroughness is evident, or when enginestalling is imminent; and shift down to 1stgear for acceleration.
05/06/09 15:54:31 31MBZ610_076
68
Braking
Basic Operation & Riding
Your motorcycle is equipped with discbraking systems which are hydraulicallyactivated. Depressing the brake pedalapplies the rear disc brake. Operating thebrake lever applies the two front discbrakes.
As a general rule, the front braking systemprovides about 70 percent of total stoppingpower.
To slow or stop, apply the brake lever andbrake pedal smoothly, while downshiftingto match your speed.
Gradually increase braking as you feel thebrakes slowing your speed. The increasein engine compression from downshiftingwill help slow your motorcycle.
To prevent stalling the engine, pull theclutch lever in before coming to acomplete stop. For support, put your leftfoot down first, then your right foot whenyou are through using the brake pedal.
Applying the brakes too hard may causethe wheels to lock and slide, reducingcontrol of your motorcycle. If this happens,release the brake controls, steer straightahead until you regain control, thenreapply the brakes more gently.
For full braking effectiveness, use boththe pedal and lever simultaneously. Usingboth braking systems will stop yourmotorcycle faster with greater stability.
05/06/09 15:54:37 31MBZ610_077
69
Braking
Basic Operation & Riding
When possible, reduce your speed orcomplete braking before entering a turn.Avoid braking or closing the throttlequickly while turning. Either action maycause one or both wheels to slip andreduce your control of your motorcycle.
Your ability to brake in a turn and to brakehard in an emergency situation areimportant riding skills. We suggestattending a Motorcycle Safety Foundationexperienced rider training course(page ) to retain these skills.
When riding in wet or rainy conditions, oron loose surfaces, the ability to maneuverand stop will be reduced. All of youractions should be smooth under theseconditions. Rapid acceleration, braking orturning may cause loss of control. For
your safety, exercise extreme cautionwhen braking, accelerating or turning.
When descending a long, steep grade, useengine compression braking bydownshifting, with intermittent use ofboth brakes. Continuous brake applicationcan overheat the brakes and reduce theireffectiveness.
Riding with your foot resting on thebrake pedal or your hand on the brakelever may actuate the brake light, givinga false indication to other drivers. Itmay also overheat the brakes, reducingeffectiveness.
50
05/06/09 15:54:42 31MBZ610_078
70
Parking
Basic Operation & Riding
CatalyticConverters
Look for a level parking area. If youcan’t park on a paved surface, makesure the ground surface is firm,especially under the side stand.If you must park on a hill, leave thetransmission in gear and position therear tire against the curb at a 45 degreeangle.
To lower the side stand, use your footto guide it down. Remember thatlowering the side stand with thetransmission in gear will stop theengine, even if the clutch lever ispulled in. That is a function of theside stand ignition cut-off system.Check that the side stand is down allthe way.If you have to park on a soft surface,insert something solid under the sidestand for support.
Use the side stand to support themotorcycle while parked.
Make sure flammable materials such asdry grass or leaves do not come in contactwith the exhaust system when parkingyour motorcycle. Refer to
, page .
1. 2.
225
05/06/09 15:54:49 31MBZ610_079
(1) ignition key
(A)
(1)
To lockFRONT
(A) push in(B) turn to LOCK(C) turn to OFF
(B)
(A)
(C)
To unlock
71
Parking
Basic Operation & Riding
(To unlock the steering lock, insert andpush down on the key and turn it to theright to the OFF position.)
Use the steering lock, which locks thehandlebar in place. Turn the handlebarall the way to the left. Push in on theignition key and turn it to LOCK.Remove the key.
(cont’d)
3.
05/06/09 15:54:55 31MBZ610_080
Riding with a helmet attached tothe holder can interfere with therear wheel or suspension andcould cause a crash in which youcan be seriously hurt or killed.
Use the helmet holder only whileparked. Do not ride with a helmetsecured by the holder.
LEFT SIDE
(2)(4)
(3)
(2) helmet holder wire(3) D-ring
(4) helmet holder
72
Parking
Basic Operation & Riding
Use the helmet holder wire stored in thetool kit to secure your helmet with yourmotorcycle:
Hook the loops of the wire onto thehelmet holder ( ) and lower the seatto lock.
Remove the helmet holder wire andstore it in the tool kit when it is not used.
Route either end of the helmet holderwire ( ) through the helmet’s D-ring( ).
Remove the seat (page ).
4.
23
98
4
05/06/09 15:55:02 31MBZ610_081
73
Theft-Prevention Tips
Parking
Basic Operation & Riding
If you decide to use an anti-theft device,select one of good quality and be sure tofollow the manufacturer’s instructions.The rear fender has a storagecompartment to store a U-shaped lockunder the seat. After storing, use therubber band ( ) to securely fasten thelock. Some U-shaped locks may not bestored in the compartment due to theirsize or design.
Park your motorcycle in a lockedgarage whenever possible. If a garageisn’t available, park in a concealed areaor in a well-lit area with enoughpedestrian traffic to discourage a thief.Always take the ignition key with you.Always use the steering lock (page ),even if you’re parking for just a minuteor two. A thief can easily push anunlocked motorcycle to a waiting truck.In addition to the steering lock, use agood quality anti-theft device madespecifically to lock a motorcycle to asecure object.
(cont’d)
1
71
05/06/09 15:55:10 31MBZ610_082
REAR
(1) rubber band
(1)
74
Parking
Basic Operation & Riding
Keep your owner’s manual, currentregistration, and insurance informationwith your motorcycle. This will make iteasier for the authorities to find you ifyour motorcycle is stolen and recovered.
05/06/09 15:55:14 31MBZ610_083
75
Riding with a Passenger or Cargo
Basic Operation & Riding
Load Limits,Loading
Guidelines,
Your motorcycle is a high-performancesport model designed to carry you and onepassenger. Whenever you add a passengeror cargo, you must be careful not toexceed the total load limits for this vehicle( page ). Make sure yourcargo is properly secured (
page ).
Also consider adjusting the suspension(page ) for the extra load.
Be aware that carrying a passenger orheavy cargo can affect acceleration,braking, and handling.
Before riding with a passenger, make sureyour passenger is wearing the properprotective apparel (page ). Also checkthat your passenger is not wearing anyloose apparel that might get caught in thedrive chain.
Tell your passenger to hold the grab rail oryour waist, lean with you in the turns, andkeep their feet on the passenger footpegsat all times, even when the motorcycle isstopped at a traffic light.
55
55
131
48
05/06/09 15:55:19 31MBZ610_084
76 Basic Operation & Riding
05/06/09 15:55:22 31MBZ610_085
77Servicing Your Honda
Servicing Your Honda
Maintenance, replacement or repair ofthe emission control devices andsystems may be performed by anymotorcycle repair establishment orindividual using parts that are‘‘certified’’ to EPA standards.
Bef ore You Service Your Honda
To help keep your motorcycle in goodshape, this section includes a MaintenanceSchedule for required service, a list ofperiodic checks you should perform atleast once a month, and step-by-stepinstructions for specific maintenance tasks.You’ll also find important safetyprecautions, information on fuels and oils,and tips for keeping your Honda lookinggreat.
For information about the exhaustemission and noise emission requirementsof the U.S. Environmental ProtectionAgency (EPA) and the California AirResources Board (CARB), see page .
For information about replacing fuses, seepage .
(cont’d)
USA only
...........The Importance of Maintenance . 80...............................Maintenance Safety . 81
............Important Safety Precautions . 82............................Periodic Maintenance . 84..........................Maintenance Schedule . 86
..............................Maintenance Record . 91220
199
05/06/09 15:55:29 31MBZ610_086
78
Servicing Your Honda
Servicing Your Honda
Service Preparations
Service Procedures
Engine
Chassis
Electrical
Fluids & Filters......................................................Fuel . 100
..............................Engine Oil & Filter . 103.................................................Coolant . 113
..........................................Air Cleaner . 117
................................................Throttle . 119......................................Clutch System . 121
................................Engine Idle Speed . 125..........................................Spark Plugs . 127
...........................................Suspension . 131..................................................Brakes . 134
.....................................................Tires . 140............................................Side Stand . 147..........................................Drive Chain . 148
..................................................Battery . 155
.................................Appearance Care . 160
.....Maintenance Component Locations . 93..................................................Tool Kit . 96
.......................Owner’s Manual Storage . 97.........................................Seat Removal . 98
..............................Side Cover Removal . 99
05/06/09 15:55:37 31MBZ610_087
*
**
*
**
79
Servicing Your Honda
Servicing Your Honda
The following table summarizes the three types of inspections and servicingrecommendations for your motorcycle. Both the pre-ride inspection and the scheduledmaintenance at the recommended intervals are necessary to assure safe and dependableperformance. The periodic checks provide additional confidence in your motorcycle’sperformance.
more often if you ride frequently or long distances; or anytime you clean your motorcycleunless you have the proper tools and service data and are mechanically qualified
Type of Inspection/Service
Maintenance SchedulePeriodic MaintenancePre-ride Inspection
Refer to page:
interval on schedulemonthlybefore every ride
your Honda dealeryouyou
Who PerformsWhen Performed518486
05/06/09 15:55:48 31MBZ610_088
Improperly maintaining thismotorcycle or failing to correct aproblem before you ride cancause a crash in which you can beseriously hurt or killed.
Always follow the inspection andmaintenance recommendationsand schedules in this owner’smanual.
80
The Importance of Maintenance
Servicing Your Honda
Keeping your motorcycle well-maintainedis absolutely essential to your safety. It’salso a good way to protect yourinvestment, get maximum performance,avoid breakdowns, and have more fun. Aproperly maintained motorcycle will alsohelp to reduce air pollution.
Remember, proper maintenance is theowner’s responsibility. Be sure to inspectyour motorcycle before each ride, performthe periodic checks, and follow theMaintenance Schedule in this section.
If your motorcycle overturns or isinvolved in a crash, be sure your Hondadealer inspects all major parts, even if youare able to make some repairs.
05/06/09 15:55:54 31MBZ610_089
Failure to properly followmaintenance instructions andprecautions can cause you to beseriously hurt or killed.
Always follow the procedures andprecautions in this owner’smanual.
81
Maintenance Safety
Servicing Your Honda
This section includes instructions on howto perform some important maintenancetasks. If you have basic mechanical skills,you can perform many of these tasks withthe tools provided with your motorcycle.
Other tasks that are more difficult andrequire special tools are best performed byprofessionals. Wheel removal shouldnormally be handled only by a Hondatechnician or other qualified mechanic.Instructions are included in this manualonly to assist in emergency service.
Some of the most important safetyprecautions follow. However, we cannotwarn you of every conceivable hazard thatcan arise in performing maintenance. Onlyyou can decide whether or not you shouldperform a given task.
05/06/09 15:55:58 31MBZ610_090
82
Important Safety Precautions
Maintenance Safety
Servicing Your Honda
Carbon monoxide poisoning fromengine exhaust.
Burns from hot motorcycle parts.
Injury from moving parts.
Read the instructions before you begin,and make sure you have the tools andskills required.
Make sure the engine is off before youbegin any maintenance or repairs. Thiswill help eliminate several potentialhazards:
Be sure there isadequate ventilation whenever youoperate the engine.
Letthe engine and exhaust system coolbefore touching.
Do not runthe engine unless instructed to do so.
To help prevent the motorcycle fromfalling over, park it on a firm, levelsurface, using the side stand or amaintenance stand to provide support.To reduce the possibility of a fire orexplosion, be careful when workingaround gasoline. Use onlynon-flammable solvent, not gasoline, toclean parts. Keep cigarettes, sparks, andflames away from all fuel-related parts.
05/06/09 15:56:04 31MBZ610_091
83
Maintenance Safety
Servicing Your Honda
Remember that your Honda dealer knowsyour motorcycle best and is fully equippedto maintain and repair it. To ensure thebest quality and reliability, use only newgenuine Honda parts or their equivalentsfor repair and replacement. If you have thetools and skills required for additionalmaintenance jobs, you can purchase anofficial Honda Service Manual (page
).230
05/06/09 15:56:07 31MBZ610_092
84
Periodic Maintenance
Servicing Your Honda
In addition to the regularly scheduledmaintenance (page ) and daily pre-rideinspection (page ), consider performingthe periodic checks on the following pageat least once a month, even if you haven’tridden your motorcycle, or as often asonce a week if you ride frequently or forlong distances. It’s a good idea to performthis maintenance any time you clean yourmotorcycle.
Check the odometer reading and performany scheduled maintenance checks that areneeded (page ). Remember, morefrequent checks may be needed for ridingin severe conditions.
86
86
51
05/06/09 15:56:11 31MBZ610_093
85
Periodic Maintenance
Servicing Your Honda
Fluids
Fuses
Make sure the headlight, brake light, taillight, and turn signals areworking properly.
Check condition, adjust slack, and lubricate as needed (page ).
Lights
Drive Chain
Freeplay
Make sure you have a full supply of spare fuses.Check the major fasteners and tighten as needed.Nuts & Bolts
Check the levels of the engine oil (page ), coolant (page ),and brake fluid (page ). Add the correct fluid as necessary, andinvestigate the cause of any low fluid level.
Tires&
Wheels
Check the air pressure with a gauge and add air if needed (page ).Examine the tread for wear (page ).Look closely for nails, embedded objects, cuts, and other types ofdamage (page ). Roll your motorcycle so you can inspect theentire surface.Check the condition of the wheels.
Check the freeplay of the clutch lever (page ) and throttle grip(page ).
140142
142
119
107 114136
148
121
05/06/09 15:56:22 31MBZ610_094
86 Servicing Your Honda
Maintenance Schedule
The required Maintenance Schedule thatfollows specifies how often you shouldhave your motorcycle serviced, and whatthings need attention. It is essential to haveyour motorcycle serviced as scheduled tomaintain safe, dependable performanceand proper emission control.
Some items in the Maintenance Schedulecan be performed with basic mechanicalskills and hand tools. Procedures for theseitems are provided in this manual. Otheritems involve more extensive proceduresand may require special training, tools,and equipment. We recommend that youhave your Honda dealer perform thesetasks unless you have advancedmechanical skills and the required toolsand equipment. Procedures for such itemsin this schedule are provided in an officialHonda Service Manual available forpurchase (page ).
The service intervals in this MaintenanceSchedule are based on average ridingconditions. Some items will need morefrequent service if you ride in unusuallywet or dusty areas or at full throttle.Consult your Honda dealer forrecommendations applicable to yourindividual needs and use.
230
05/06/09 15:56:27 31MBZ610_095
* **
*
**
87
Maintenance Schedule
Servicing Your Honda
If you do not feel capable of performing agiven task or need assistance, rememberthat your Honda dealer knows yourmotorcycle best and is fully equipped tomaintain and repair it. If you decide to doyour own maintenance, use only genuineHonda parts or their equivalents for repairor replacement to ensure the best qualityand reliability.
Perform the pre-ride inspection (page )and owner maintenance (page ) at eachscheduled maintenance period.
Each item on the maintenance schedulerequires some mechanical knowledge.Certain items (particularly those marked
and ) may require more technicalinformation and tools. Consult yourHonda dealer.
Should be serviced by your Hondadealer, unless you have the proper toolsand service data and are mechanicallyqualified. Refer to the official HondaService Manual (page ).In the interest of safety, we recommendthese items be serviced only by yourHonda dealer.
88 23051
05/06/09 15:56:32 31MBZ610_096
88 Servicing Your Honda
Maintenance Schedule
Summary of Maintenance Schedule Notes& Procedures:
At higher odometer readings, repeat atthe frequency interval established here.Service more frequently if themotorcycle is ridden in unusually wet ordusty areas.
Maintenance Procedures:I: inspect and clean, adjust, lubricate,
or replace, if necessaryC: cleanA: adjustL: lubricateR: replace
Replace every 2 years, or at indicatedodometer interval, whichever comesfirst. Replacement requires mechanicalskill. Refer to the official Hondaservice manual.California type only.
NOTES:1.
2.
3.
4.
05/06/09 15:56:40 31MBZ610_097
××
---
-
-
--
-
***
*
**
**
*
*
**
4
6.4
I
I
20
32.0
I
I
12
19.2
I
I
I
I
0.6
1.0
R
I
8
12.8
I
I
I
R
R
I
I
I
I
I
16
25.6
I
I
I
R
I
R
I
I
I
I
I
24
38.4
I
I
I
I
R
R
I
I
R
I
I
I
NOTE
2
3
4
Refer to
page
117
127
103
108
125
113
ODOMETER READING (Note 1)
ITEM
FREQUENCYE
MIS
SIO
NR
ELA
TE
DIT
EM
S
1,000 mi
1,000 km
CARBURETOR SYNCHRONIZATION
FUEL LINE
THROTTLE OPERATION
CHOKE OPERATION
AIR CLEANER
SPARK PLUGS
VALVE CLEARANCE
ENGINE OIL
ENGINE OIL FILTER
ENGINE IDLE SPEED
RADIATOR COOLANT
COOLING SYSTEM
SECONDARY AIR SUPPLY
SYSTEM
EVAPORATIVE EMISSION
CONTROL SYSTEM
INITIAL = 600mi (1,000km) or 1month : R
REGULAR = EVERY 8,000mi (12,800km) or 12months : R
89Servicing Your Honda
Maintenance Schedule
Should be serviced by your Honda dealer, unless you have the proper tools and service data and aremechanically qualified. Refer to the official Honda Service Manual (page ).In the interest of safety, we recommend these items be serviced only by your Honda dealer.
230
05/06/09 15:56:50 31MBZ610_098
××
--
----
**
******
*
**
1,000 mi
1,000 km
DRIVE CHAIN
BRAKE FLUID
BRAKE PAD WEAR
BRAKE SYSTEM
BRAKE LIGHT SWITCH
HEADLIGHT AIM
CLUTCH SYSTEM
SIDE STAND
SUSPENSION
NUTS, BOLTS, FASTENERS
WHEELS/TIRES
STEERING HEAD
BEARINGS
0.6
1.0
I
I
I
I
4
6.4
I
I
I
8
12.8
I
I
I
I
I
I
I
I
I
I
I
12
19.2
R
I
I
16
25.6
I
I
I
I
I
I
I
I
I
I
I
20
32.0
I
I
I
24
38.4
R
I
I
I
I
I
I
I
I
I
I
NOTE
3
Refer to
page
148
135
138
134
121
147
ODOMETER READING (Note 1)
ITEM
FREQUENCY
I, L EVERY 500 mi (800 km)
NO
N-E
MIS
SIO
NR
ELA
TE
DIT
EM
S
90
Maintenance Schedule
Servicing Your Honda
Should be serviced by your Honda dealer, unless you have the proper tools and service data and aremechanically qualified. Refer to the official Honda Service Manual (page ).In the interest of safety, we recommend these items be serviced only by your Honda dealer.
230
05/06/09 15:57:01 31MBZ610_099
91
Maintenance Record
Servicing Your Honda
Miles (km) Odometer Date Performed By: Notes600 (1,000)
4,000 (6,400)8,000 (12,800)
12,000 (19,200)16,000 (25,600)20,000 (32,000)
Keeping an accurate maintenance record will help ensure that your motorcycle is properlymaintained. Retain detailed receipts to verify the maintenance was performed. If themotorcycle is sold, these receipts should be transferred with the motorcycle to the new owner.Make sure whoever performs the maintenance completes this record. All scheduledmaintenance, including the 600 mile (1,000 km) initial maintenance, is considered a normalowner operating cost and will be charged for by your dealer. Use the space under Notes torecord anything you want to remind yourself about or mention to your dealer.
05/06/09 15:57:08 31MBZ610_100
92
Maintenance Record
Servicing Your Honda
Miles (km) Odometer Date NotesPerformed By:24,000 (38,400)28,000 (44,800)32,000 (51,200)36,000 (57,600)40,000 (64,000)44,000 (70,400)48,000 (76,800)52,000 (83,200)56,000 (89,600)60,000 (96,000)64,000 (102,400)68,000 (108,800)
05/06/09 15:57:14 31MBZ610_101
fuel fill cap
front brake fluid reservoir
front brake lever
throttle grip
choke lever
clutch lever
93Servicing Your Honda
Maintenance Component Locations
05/06/09 15:57:17 31MBZ610_102
rear brake fluidreservoir
rear brakecaliper
front brakecaliper
coolant reserve tank
battery
tool kit main fuse
engine oil filler cap/dipstick
rear brake pedal engine oil filter
94 Servicing Your Honda
Maintenance Component Locations
05/06/09 15:57:22 31MBZ610_103
drive chain
fuse box
front brake caliper
rear spring pre-load adjusterspark plugs
owner’s manual
engine idle speed
engine oil drain bolt
95Servicing Your Honda
Maintenance Component Locations
05/06/09 15:57:26 31MBZ610_104
(1) tool kit
(2)
(1)
UNDER SEAT
(2) tool kit compartment
96
Tool Kit
Servicing Your Honda
The tool kit ( ) is stored in the tool kitcompartment ( ) under the seat (page ).An optional, larger tool kit may beavailable. Check with your Honda dealer’sparts department.
1982
05/06/09 15:57:31 31MBZ610_105
(1)
(2)
UNDER SEAT
(1) storage bag(2) owner’s manual storage compartment
97
Owner’s Manual Storage
Servicing Your Honda
Your motorcycle provides storage for theowner’s manual so you’ll have it with youfor easy reference. Store your owner’smanual (and other documents) in theplastic storage bag ( ) in the storagecompartment ( ) under the seat.
Be careful not to flood this area whenwashing your motorcycle.
12
05/06/09 15:57:36 31MBZ610_106
(4)
(5)
(6)
(1)
(3)
(2)
(7)
(1) ignition key(2) seat lock(3) seat(4) front prongs
(5) front stays(6) rear prongs(7) rear stays
98
Seat Removal
Servicing Your Honda
Saf ety PrecautionsRefer to on page . Removal
Pull the seat ( ) back and up.
Installation
Insert the ignition key ( ) into the seatlock ( ).Turn it clockwise and pull up on therear of the seat ( ).
Push forward and then down on the rearof the seat.
Be sure to securely lock the seat afterreinstalling it.
Insert the front prongs ( ) into the frontstays ( ) and the rear prongs ( ) intothe rear stays ( ) on the frame.
The seat must be removed to use thehelmet holder or to access the tool kit andowner’s manual.
1.
2.
2.
3.
1.
1
3
2
65
82
3
4
7
05/06/09 15:57:49 31MBZ610_107
(4)
(5)
(3) (2)
(1)
(1) bolt(2) tab A(3) grommet
(4) tab B(5) side cover
99
Side Cover Removal
Servicing Your Honda
Saf ety PrecautionsRefer to on page . InstallationInstallation can be done in the reverseorder of removal.The right side cover must be removed for
the battery maintenance. The left sidecover must be removed for air cleaner,suspension adjustment and fusemaintenance.
The right and left side covers can beremoved in the same manner.
Remove the side cover ( ).
Remove tab A ( ) from the grommet( ).Remove tab B ( ) from the rear cowl.
Remove the bolt ( ).Removal1.2.
3.4.
82
12
34
5
05/06/09 15:58:03 31MBZ610_108
unleaded86 (or higher)
typepump octanenumber
100
Fuel Recommendation
Fuel
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
We recommend that you use unleaded fuelbecause it produces fewer engine depositsand extends the life of exhaust systemcomponents.
If pinging or spark knock occurs at asteady engine speed under normal load,change brands of gasoline. If pinging orspark knock persists, consult your Hondadealer.
Use of lower octane gasoline can causepersistent ‘‘pinging’’ or ‘‘spark knock’’ (aloud rapping noise) which, if severe, canlead to engine damage. Light pingingexperienced while operating under a heavyload, such as climbing a hill, is no causefor concern.
Your engine is designed to use anygasoline that has a pump octane number of86 or higher. Gasoline pumps at servicestations normally display the pump octanenumber. For information on the use ofoxygenated fuels, see page .
The use of leaded gas will damage thecatalytic converter.
82
226
05/06/09 15:58:13 31MBZ610_109
4.49 US gal (17.0 )
(3)
(1) ignition key(2) fuel fill cap
(3) filler neck
(2)
(1)
101
Refueling Procedure
Fuel Capacity
Fuel
Servicing Your Honda
Saf ety Precautions
Never use stale or contaminated gasolineor an oil/gasoline mixture. Avoid gettingdirt, dust, or water in the fuel tank.
Refer to on page .
Insert the ignition key ( ) in the fuelfill cap ( ) and turn it clockwise.
Fuel tank capacity:
The tank should be refilled as soon aspossible when the fuel indicator comes on.
(cont’d)
1. 12
82
05/06/09 15:58:22 31MBZ610_110
Gasoline is highly flammable andexplosive. You can be burned orseriously injured when handlingfuel.
Stop the engine and keep heat,sparks and flame away.Handle fuel only outdoors.Wipe up spills immediately.
102
Fuel
Servicing Your Honda
Open the cap.Add fuel until the level reaches thebottom of the filler neck ( ). Avoidoverfilling the tank. There should be nofuel in the filler neck.
After refueling, push the fuel fill capclosed until it snaps and locks.Remove the ignition key from the cap.
2.3.
3 5.
4.
05/06/09 15:58:28 31MBZ610_111
103
Engine Oil & Filter
Servicing Your Honda
Engine oil quality is a major factor thataffects both the performance and theservice life of the engine.
When running in very dusty conditions, oilchanges should be performed morefrequently than specified in themaintenance schedule.
Using the proper oil (page ) and filter,and regularly checking, adding, andchanging oil will help extend yourengine’s life. Even the best oil wears out.Changing oil helps get rid of dirt anddeposits in the engine. Operating theengine with old or dirty oil can damageyour engine. Running the engine withinsufficient oil can cause serious damageto the engine and transmission.
Change the engine oil as specified in themaintenance schedule on page .
104
89
05/06/09 15:58:34 31MBZ610_112
*
*
Pro Honda GN4 or HP4 (withoutmolybdenum additives) 4-strokeoil (USA & Canada), or Honda4-stroke oil (Canada only), or anequivalent motorcycle oil.
MA
SG or higherexcept oilslabeled as energyconserving on thecircular APIservice labelSAE 10W-40
APIclassification
JASO T 903standard
viscosity(weight)
suggested oil
104
Oil Recommendation
Engine Oil & Filter
Servicing Your Honda
Suggested oils are equal in performanceto SJ oils that are not labeled as energyconserving on the circular API servicelabel.
05/06/09 15:58:42 31MBZ610_113
OKNOT RECOMMENDED
105
Engine Oil & Filter
Servicing Your Honda
Do not use oils with graphite ormolybdenum additives. They mayadversely affect clutch operation.
Your motorcycle does not need oiladditives. Use the recommended oil.
Other viscosities shown in the followingchart may be used when the averagetemperature in your riding area is withinthe indicated range.
Do not use non-detergent, vegetable, orcastor based racing oils.
Do not use API SH or higher oilsdisplaying a circular API ‘‘energyconserving’’ service label on thecontainer. They may affect lubricationand clutch performance.
05/06/09 15:58:51 31MBZ610_114
(1) code number of the sales companyof the oil
(2) oil classification
(1)
(2)
106
Engine Oil & Filter
Servicing Your Honda
JASO T 903 standardThe JASO T 903 standard is an index forengine oils for 4-stroke motorcycleengines.There are two classes: MA and MB.Oil conforming to the standard is labeledon the oil container. For example, thefollowing label shows the MAclassification.
05/06/09 15:58:55 31MBZ610_115
-
-
RIGHT SIDE
(2)
(3)
(1)
(1) upper level mark(2) lower level mark(3) engine oil filler cap/dipstick
107
Checking & Adding Oil
Engine Oil & Filter
Servicing Your Honda
Saf ety Precautions
(cont’d)
Refer to on page .
Hold the motorcycle in an uprightposition.
Remove the oil filler cap/dipstick ( )and wipe it clean.
Stop the engine and wait 2 3 minutes.
Start the engine and let it idle for 3 5minutes. Make sure the low oil pressureindicator goes off. If the indicatorremains on, stop the engineimmediately.
Park your motorcycle on its side standon a firm, level surface.
Insert the oil filler cap/dipstick until itseats, but don’t screw it in.
2.
3.4.
5.
6.
1
1.
82
05/06/09 15:59:04 31MBZ610_116
108
Changing Engine Oil & Filter
Engine Oil & Filter
Servicing Your Honda
Saf ety Precautions
Using the wrong oil f ilter may result inleaks or premature engine damage.
Refer to on page .
Your motorcycle’s oil filter has veryspecific performance requirements. Use anew genuine Honda oil filter or a filter ofequal quality specified for your model.
If the oil is at or near the upper levelmark ( ) –– you do not have to addoil.If the oil is below or near the lowerlevel mark ( ) –– add therecommended oil until it reaches theupper level mark. (Do not overfill.)
Reinstall the oil filler cap/dipstick.Check for oil leaks.
Remove the oil filler cap/dipstick andcheck the oil level.
7.
8.9.
1 82
2
05/06/09 15:59:11 31MBZ610_117
--
(2) sealing washer
LEFT SIDE
(1) crankcasedrain bolt
(1)(2)
109
Engine Oil & Filter
Servicing Your Honda
Drain the Engine Oil:
This procedure requires mechanical skilland professional tools such as a torquewrench and oil filter wrench, as well as ameans for disposing of the drained fluid(page ). If you do not have the skillsor the tools, see your Honda dealer.
Park the motorcycle on its side stand ona firm, level surface.If the engine is cold, start it and let itidle for 3 5 minutes. Turn the engineoff. Wait 2 3 minutes for the oil tosettle.
Place a drain pan under the crankcasedrain bolt ( ).
(cont’d)
To drain the oil, remove the oil fillercap/dipstick, crankcase drain bolt ( ),and sealing washer ( ).
1.
2.
3.
4.
1751
2
1
05/06/09 15:59:19 31MBZ610_118
(3) oil filter
FRONT
(3)
110
Engine Oil & Filter
Servicing Your Honda
Install a New Oil Filter:
Improper disposal of drained f luids isharmf ul to the environment.
Remove the oil filter ( ) with a filterwrench and let the remaining oil drainout. Discard the oil filter in an approvedmanner (page ).
Pour the drained oil into a suitablecontainer and dispose of it in anapproved manner (page ).
5.6.
175
1753
05/06/09 15:59:27 31MBZ610_119
20 lbf·ft (26 N·m , 2.7 kgf·m)
22 lbf·ft (29 N·m , 3.0 kgf·m)
3.7 US qt (3.5 )(4) oil filter rubber seal
(4)
111
Engine Oil & Filter
Servicing Your Honda
Add Engine Oil:
Apply a thin coat of engine oil to therubber seal ( ) of a new oil filter.
Install the new oil filter and tighten it byhand.
Check the condition of the sealingwasher on the drain bolt. Replace thewasher every other time the oil ischanged.Install the drain bolt and tighten it to thespecified torque:
Fill the crankcase with therecommended oil (page ),approximately:
Using an oil filter wrench attachmentand a torque wrench, tighten the new oilfilter to the specified torque:
(cont’d)
Install the oil filler cap/dipstick securely.
7.
8.
10.
11.
12.
9.
104
4
05/06/09 15:59:37 31MBZ610_120
-
-
112
Engine Oil & Filter
Servicing Your Honda
Start the engine and let it idle for 3 5minutes.Stop the engine and wait 2 3 minutes.Hold the motorcycle upright and checkthat the oil level is at the upper levelmark on the oil filler cap/dipstick (page
).
If a torque wrench is not used forinstallation, see your Honda dealer as soonas possible to verify proper assembly.
Check that there are no oil leaks.
13.
14.15.
16.107
05/06/09 15:59:43 31MBZ610_121
113
Coolant Recommendation
Coolant
Servicing Your Honda
Using coolant with silicate inhibitors maycause premature wear of water pumpseals or blockage of radiator passages.Using tap water may cause enginedamage.
Your motorcycle’s liquid cooling systemdissipates engine heat through the coolantjacket that surrounds the cylinder andcylinder head.
Use Pro Honda HP coolant or anequivalent high quality ethylene glycolantifreeze containing corrosion protectioninhibitors specifically recommended foruse in aluminum engines. Check theantifreeze container label.
Maintaining the coolant will allow thecooling system to work properly andprevent freezing, overheating, andcorrosion.
Decreasing the concentration of antifreezeto less than 40% will not provide propercorrosion protection.
The factory provides a 50/50 solution ofantifreeze and water in this motorcycle.This coolant solution is recommended formost operating temperatures and providesgood corrosion protection.
Use only distilled water as a part of the
coolant solution. Water that is high inmineral content or salt may be harmful tothe aluminum engine.
05/06/09 15:59:50 31MBZ610_122
(1) UPPER level mark(2) LOWER level mark(3) reserve tank cap
(1)
(2)
(3)
LEFT SIDE
114
Checking & Adding Coolant
Coolant
Servicing Your Honda
Saf ety Precautions
Increasing the concentration of antifreezeis not recommended because it decreasescooling system performance. Higherconcentrations of antifreeze (up to 60%)should only be used to provide additionalprotection against freezing. Check thecooling system frequently during freezingweather.
Refer to on page .82
05/06/09 15:59:57 31MBZ610_123
115
Coolant Replacement
Coolant
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
With the engine at normal operatingtemperature, check the coolant level inthe reserve tank. It should be betweenthe UPPER ( ) and LOWER ( ) levelmarks.If the reserve tank is empty, or ifcoolant loss is excessive, check forleaks and see your Honda dealer forrepair.
Coolant should be replaced by your Hondadealer, unless you have the proper toolsand service data and are mechanicallyqualified. Refer to the official HondaService Manual (page ).
Add coolant to the reserve tank asrequired to bring the coolant level to theUPPER level mark.
Remove the reserve tank cap ( ).Always add coolant to the reserve tank.Do not attempt to add coolant byremoving the radiator cap.
Remove the seat (page ).
1
1.
2.3.
4.
398
82
230
2
05/06/09 16:00:06 31MBZ610_124
Removing the radiator cap whilethe engine is hot can cause thecoolant to spray out, seriouslyscalding you.
Always let the engine and radiatorcool down before removing theradiator cap.
116
Coolant
Servicing Your Honda
You & the Environment,
Improper disposal of drained f luids isharmf ul to the environment.
To properly dispose of drained coolant,refer to page
.175
05/06/09 16:00:10 31MBZ610_125
117
Air Cleaner
Servicing Your Honda
Saf ety Precautions
Using the wrong air cleaner may result inpremature engine damage.
Improper or lack of proper air cleanermaintenance can cause poor perf ormanceand premature engine wear.
Refer to on page .
Service the air cleaner more frequently ifyou ride in unusually wet or dusty areas.Your Honda dealer can help youdetermine the correct service interval foryour riding conditions.
Your motorcycle’s air cleaner has veryspecific performance requirements. Use anew genuine Honda air cleaner specifiedfor your model or an air cleaner ofequivalent quality.
Proper air cleaner maintenance canprevent premature engine wear or damage,expensive repairs, low engine power, poorgas mileage, and spark plug fouling.
82
05/06/09 16:00:16 31MBZ610_126
(3)(2)
(1)
LEFT SIDE
LEFT SIDE
(3) air cleaner
(1) attaching screws(2) air cleaner housing cover
118
Replacement
Air Cleaner
Servicing Your Honda
Remove the attaching screws (1) and aircleaner housing cover (2).
Remove the left side cover (page ).
Pull out the air cleaner (3) and clean theair cleaner using compressed air fromthe outside, or replace it if necessary.Install the air cleaner.Install the removed parts in the reverseorder of removal.
1.2.
3.
4.5.
99
05/06/09 16:00:23 31MBZ610_127
- -1/16 1/4 in (2 6 mm)
RIGHT HANDLEBAR
(1) lock nut (2) adjuster
(2)(1)
119
Throttle Freeplay
Throttle
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
InspectionCheck freeplay at the throttle grip flange.Freeplay:
If necessary, adjust to the specified range.
AdjustmentLoosen the lock nut ( ).Turn the adjuster ( ).After adjustment, check for smoothrotation of the throttle grip from fullyclosed to fully open in all steeringpositions.
1.2.3.
1
82
2
05/06/09 16:00:34 31MBZ610_128
120
Throttle Inspection
Throttle
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Check that the throttle assembly ispositioned properly and the securingbolts are tight.Check for smooth rotation of thethrottle from fully open to fully closedin all steering positions. If there is aproblem, see your Honda dealer.
1.
2.
82
05/06/09 16:00:39 31MBZ610_129
LEFT HANDLEBAR
(1) clutch lever
(1)
121
Clutch Freeplay
Clutch System
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Your motorcycle’s manually-activated,wet, multiplate clutch is part of theprimary drive system. Proper freeplayadjustment allows a smooth, gradualengagement when shifting gears.
Improper freeplay adjustment can causepremature clutch wear.
82
05/06/09 16:00:45 31MBZ610_130
- -
+-
++
--
3/8 13/16 in (10 20 mm)
LEFT HANDLEBAR
(2)
(3)
(2) upper lock nut(3) upper clutch cable adjuster( ) increase freeplay( ) decrease freeplay
(( ))
(( ))
122
Clutch System
Servicing Your Honda
InspectionCheck freeplay:
If necessary, adjust to the specifiedrange.
Upper AdjustmentAttempt adjustment with the upper clutchcable adjuster first.
Loosen the upper lock nut ( ).Turn the upper clutch cable adjuster ( )to obtain the specified freeplay.Tighten the upper lock nut and checkthe freeplay again.
1.
1.2.
3.
32
05/06/09 16:00:54 31MBZ610_131
+-
++
--
RIGHT SIDE
(4)
(5)
( ) increase free play( ) decrease free play
(( ))
(( ))
(4) lower lock nut(5) lower
adjusting nut
123
Clutch System
Servicing Your Honda
Lower AdjustmentIf the upper clutch cable adjuster isthreaded out near its limit –– or the correctfreeplay cannot be obtained –– attemptadjustment with the lower clutch cableadjuster.
Loosen the upper lock nut ( ) and turnthe upper clutch cable adjuster ( ) allthe way in (to provide maximumfreeplay). Tighten the upper lock nut.Loosen the lower lock nut ( ).Turn the lower adjusting nut ( ) toobtain the specified freeplay.Tighten the lower lock nut and checkthe adjustment.
(cont’d)
1.
2.3.
4.
23
45
05/06/09 16:01:03 31MBZ610_132
124
Other Inspections & Lubrication
Clutch System
Servicing Your Honda
Start the engine, pull the clutch lever in,and shift into gear. Make sure theengine does not stall and the motorcycledoes not creep. Gradually release theclutch lever and open the throttle. Yourmotorcycle should move smoothly andaccelerate gradually.
If you cannot get proper adjustment, or theclutch does not work properly, the cable orclutch friction discs may be worn. Seeyour Honda dealer or refer to the officialHonda Service Manual (page ).
Lubricate the clutch cable with acommercially-available cable lubricantto prevent premature wear andcorrosion.
Check the clutch cable for kinks orsigns of wear. If necessary, have itreplaced.
Check that the clutch lever assembly ispositioned properly and the securingbolts are tight.
5.
230
05/06/09 16:01:10 31MBZ610_133
+-
++
--
(1) throttle stopscrew
( ) increase( ) decrease
(1)
LEFT SIDE
(( ))
(( ))
125
Idle Speed Adjustment
Engine Idle Speed
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Remember, idle speed adjustment is not a‘‘cure-all’’ for other problems in yourengine’s fuel-delivery system. Adjustingthe idle will not compensate for a faultelsewhere.
The engine must be at normal operatingtemperature for accurate idle speedadjustment.
If the engine is cold, start it and warm itup with ten minutes of stop-and-goriding. Stop the engine.
(cont’d)
1.
82
05/06/09 16:01:18 31MBZ610_134
±1,400 100 rpm
126
Engine Idle Speed
Servicing Your Honda
Adjust idle speed with the throttle stopscrew ( ).Idle speed (in neutral):
Shift into neutral. Start the engine.
Place your motorcycle on its side standon a firm, level surface.
3.4.
1
2.
05/06/09 16:01:22 31MBZ610_135
CR9EH-9 (NGK)
U27FER9 (DENSO)or
standardspark plug
LEFT SIDE
(1) radiator connector(2) fan motor switch connector
(1)
(2)
127
Spark Plug Recommendation Spark Plug Replacement &Inspection
Spark Plugs
Servicing Your Honda
Using spark plugs with an improper heatrange can cause engine damage.
Saf ety Precautions
Use only the recommended type of sparkplugs in the recommended heat range.
Refer to on page .
Disconnect the radiator connector ( )and fan motor switch connector ( ).
(cont’d)
1.
82
12
05/06/09 16:01:31 31MBZ610_136
FRONT
(3) radiatormount bolts
(4) collars(5) radiator
(6) grommet(7) radiator stay
(5)
(3)
(4)
(6)
(7)
128
Spark Plugs
Servicing Your Honda
Remove the radiator mount bolts ( )and collars ( ).Move the radiator ( ) out of the wayand remove the grommet ( ) from theradiator stay ( ).Pull the radiator toward the front.
2.
3.
4.
43
56
7
05/06/09 16:01:38 31MBZ610_137
FRONT
(8) (9)
(8) spark plug cap(9) spark plug wrench
129
Spark Plugs
Servicing Your Honda
Disconnect the spark plug caps ( ).Take care to avoid damaging the sparkplug wire when disconnecting the caps.
Clean any dirt from around the sparkplug base.
Using the spark plug wrench ( )provided in the tool kit, remove thespark plugs.Inspect the electrodes and centerporcelain for deposits, corrosion, orcarbon fouling. If the corrosion ordeposits are heavy, replace the plug.Clean a carbon or wet-fouled plug witha plug cleaner, if available, or a wirebrush.
(cont’d)
5.
6.
7.
8.
8
9
05/06/09 16:01:45 31MBZ610_138
- -0.031 0.035 in (0.80 0.90 mm)
(10) spark plug gap (11) side electrode
(11)
(10)
130
Spark Plugs
Servicing Your Honda
Improperly tightened spark plugs candamage the engine. If a plug is too loose,a piston may be damaged. If a plug is tootight, the threads may be damaged.
Check the spark plug gap ( ) of eachnew plug, using a wire-type feelergauge. If adjustment is necessary, bendthe side electrode ( ) carefully.The gap should be:
With the plug washers attached, threadthe spark plugs in by hand to preventcross-threading.Tighten the spark plug:
If the old plug is good:1/8 turn after it seats.
If installing a new plug, tighten ittwice to prevent loosening:
First, tighten the plug:NGK: turn after it seats.DENSO: turn after it seats.Then loosen the plug.Next, tighten the plug again:1/8 turn after it seats.
Reinstall the spark plug caps. Take careto avoid pinching any cables or wires.Install the remaining parts in the reverseorder of removal.
a)
b)c)
1/21/21/2
9.
10.
11.
1
13.
12.
10
11
05/06/09 16:01:56 31MBZ610_139
131
Suspension
Servicing Your Honda
The way you ride your motorcycle and thetype of ride you want to experience canalso influence your suspension needs.
Your front and rear suspension systemsuse springs and hydraulic damping devicesthat suspend your weight and most of theweight of your motorcycle.
The spring pre-load for your rearsuspension system adjusts the amount offorce required to begin compression of thespring.
The oil damper systems hydraulicallycontrol the natural compression andrebound of the suspension springs so thattraction and comfort are maintained as thewheels ride over road surfaces.
Consider adjusting your rear suspensionpre-load whenever you change yournormal load, by adding or subtracting apassenger, cargo, or accessories, or whenthe road or riding conditions change.
Lower spring pre-load provides a softerride and is usually preferred for light loadsand smooth roads. Higher spring pre-loadprovides a firmer ride and isrecommended for heavy loads, rough roadconditions, and faster, more challengingriding.
05/06/09 16:02:02 31MBZ610_140
132
Rear Suspension Adjustment
Suspension
Servicing Your Honda
The rear suspension can be adjusted forrider (and passenger) weight and ridingconditions by changing the spring pre-load.
The rear shock absorber includes a damperunit that contains high pressure nitrogengas. Do not attempt to disassemble,service, or dispose of the damper; see yourHonda dealer. The instructions found inthis owner’s manual are limited toadjustments of the shock assembly only.
05/06/09 16:02:06 31MBZ610_141
(1)
(3)
(2)
(1) spring adjuster(2) pin spanner
(3) extension bar
RIGHT SIDE 321 4 75
6
133
Rear Suspension Spring Pre-load
Suspension
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
The spring pre-load adjuster ( ) haspositions for different load or riding
conditions.
Always adjust the shock absorber positionin sequence (1-2-3-4-5-6-7 or 7-6-5-4-3-2-1). Attempting to adjust directly from 1 to7 or 7 to 1 may damage the shock absorber.
Positions 3 to 7: for when the motorcycleis more heavily loaded. (Also increasespring pre-load for stiffer rear suspension.)
Position 2: standard position.
Position 1: for a light load and smoothroad conditions.
Remove the left side cover (page ),then use the pin spanner ( ) and extensionbar ( ) to adjust the rear shock spring pre-load.
71
8299
23
05/06/09 16:02:21 31MBZ610_142
(1) adjuster(2) arrow
(3) brake lever(4) index mark
(4)
(2)
(3)
(1)
134
Front Brake Lever Adjustment
Brakes
Servicing Your Honda
Saf ety Precautions
The hydraulic braking systems on yourmotorcycle dissipate the heat generated bythe friction of the brake pads on the brakediscs as the wheels are slowed.
As the brake pads wear, the brake fluidlevel will drop. A leak in the system willalso cause the level to drop.
Frequently inspect the system to ensurethere are no fluid leaks. Periodicallyinspect the brake fluid level and the brakepads for wear.
If the brake lever or brake pedal freeplaydoes not feel within the normal rangewhile riding, check the brake pads forwear (page ). Worn pads should bereplaced. If the pads are not worn beyondthe recommended limit, there is probably
air in the brake system. See your Hondadealer to have the air bled from the system.
Refer to on page .
The distance between the tip of the brakelever and the grip may be adjusted.
138
82
05/06/09 16:02:29 31MBZ610_143
Honda DOT 4 BrakeFluid
brakefluid
135
Brake Fluid Recommendation
Brakes
Servicing Your Honda
The recommended brake fluid is HondaDOT 4 Brake Fluid, or any brake fluid ofequal quality and performance. Use freshbrake fluid from a sealed container. Besure to read the label before opening thesealed container. An opened containermay be contaminated or may haveabsorbed moisture from the air.
Apply the brake, release it, then spin thewheel and check that it rotates freely.Repeat this procedure several times.
Align the arrow ( ) on the brake lever( ) with the index mark ( ) on theadjuster.
Turn the adjuster ( ).2.
3.
1. 12
3 4
05/06/09 16:02:36 31MBZ610_144
(1)
RIGHT FRONT
(1) LOWER level mark
136
Fluid Level Inspection
Brakes
Servicing Your Honda
Saf ety Precautions
Brake f luid can damage plastic andpainted surf aces. Handle with care.
Refer to on page .
If your inspection indicates a low fluidlevel, have your Honda dealer add therecommended brake fluid.
Wipe up spills immediately. Avoid contactwith skin or eyes. In case of contact, washthoroughly and call a doctor immediatelyif it contacts your eyes.
Do not add or replace brake fluid, exceptin an emergency. If you do add fluid, haveyour Honda dealer check the system assoon as possible.
82
05/06/09 16:02:43 31MBZ610_145
RIGHT SIDE
(1)
(1) LOWER level mark
(2)
(2) UPPER level mark
137
Brakes
Servicing Your Honda
Place your motorcycle in an uprightposition on a firm, level surface.
Check the fluid level. It should bebetween the UPPER ( ) and LOWER( ) level marks. If the level is at orbelow the LOWER level mark, checkthe brake pads for wear (page ).
Worn pads should be replaced. If thepads are not worn beyond therecommended limit, have your brakesystem inspected for leaks.
Check for deterioration or cracks in thehoses and fittings.
Make sure there are no fluid leaks.Other Inspections
Remove the right side cover (page ).
1.
2.
1
3.
99
138
2
05/06/09 16:02:51 31MBZ610_146
(1)
LEFT FRONT (Right side similar)
(1) cutouts
138
Brake Pad Wear
Brakes
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Brake pad wear depends upon the severityof usage, the type of riding, and roadconditions. Generally, the pads will wearfaster on wet and dirty roads. Inspect thepads at each regular maintenance interval(page ).
Front Brake
Always inspect both pads in both the rightand left brake calipers.
Check the cutouts ( ) in each pad. Ifeither pad is worn to the cutout, replaceboth pads as a set. See your Honda dealerfor this service.
82
90
1
05/06/09 16:02:59 31MBZ610_147
RIGHT REAR
(2)
(2) cutouts
139
Brakes
Servicing Your Honda
Rear Brake Check the cutouts ( ) in each pad. Ifeither pad is worn to the cutout, replaceboth pads as a set. See your Honda dealerfor this service.
2
05/06/09 16:03:08 31MBZ610_148
Using tires that are excessivelyworn or improperly inflated cancause a crash in which you can beseriously hurt or killed.
Follow all instructions in thisowner’s manual regarding tireinflation and maintenance.
140
Air Pressure
Tires
Servicing Your Honda
Saf ety Precautions
Properly inflated tires provide the bestcombination of handling, tread life, andriding comfort. Generally, underinflatedtires wear unevenly, adversely affecthandling, and are more likely to fail frombeing overheated. Overinflated tires makeyour motorcycle ride harshly, are moreprone to damage from road hazards, andwear unevenly.
Refer to on page .
To safely operate your motorcycle, yourtires must be the proper type and size, ingood condition with adequate tread, andcorrectly inflated for the load you arecarrying.
The following pages give detailedinformation on how and when to checkyour air pressure, how to inspect your tires
for wear and damage, and ourrecommendations for tire repair andreplacement.
82
05/06/09 16:03:15 31MBZ610_149
36 psi (250 kPa ,2.50 kgf/cm )42 psi (290 kPa ,2.90 kgf/cm )
front
rear
141
Tires
Servicing Your Honda
We recommend that you visually checkyour tires before every ride and use an airpressure gauge to measure the air pressureat least once a month or any time youthink the tires might be low. Even tiresthat are in good condition may lose one totwo psi per month if not checked andadjusted regularly.
Tubeless tires have some degree of self-sealing ability if they are punctured.However, because leakage is often veryslow, you should look closely forpunctures whenever a tire is not fullyinflated.
Always check air pressure when your tiresare ‘‘cold’’ –– after the motorcycle hasbeen parked for at least three hours. If youcheck air pressure when your tires are
‘‘warm’’ –– even if your motorcycle hasonly been ridden for a few miles –– thereadings will be higher. If you let air outof warm tires to match the recommendedcold pressures, the tires will beunderinflated.
The recommended ‘‘cold’’ tire pressuresare:
05/06/09 16:03:21 31MBZ610_150
(1)
(2)
(1) wear indicator(2) wear indicator location mark
142
Inspection
Tires
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Whenever you check the tire pressures,you should also look for:
Bumps or bulges in the side of the tireor the tread. Replace any tire that has abump or bulge.Cuts, slits, or cracks in the tires.Replace the tire if you can see fabric orcord.Nails or other foreign objects embeddedin the side of the tire or tread.Excessive tread wear.
Also, if you hit a pothole or hard objectwhile riding, pull to the side of the road assoon as you safely can and carefullyinspect the tires for damage.
Tread Wear
82
05/06/09 16:03:31 31MBZ610_151
0.06 in (1.5 mm)0.08 in (2.0 mm)
frontrear
143
Tire Repair
Tires
Servicing Your Honda
Saf ety Precautions
If You Have a Flat Tire,
For the best performance, you shouldreplace a tire before the tread depth at thecenter reaches the following limits:
We strongly recommend that you replace,not repair, any tire that is punctured ordamaged. As discussed below, a tire that isrepaired, either temporarily orpermanently, will have lower speed andperformance limits than a new orundamaged tire.
If the wear indicators are visible, replacethe tire immediately as it is no longer safe.
Refer to on page .
A temporary repair can sometimes bemade in an emergency situation.However, since a temporary repair maynot hold, you must ride very slowly,preferably without any cargo or passenger,and have the tire replaced or permanentlyrepaired as soon as possible.(For more information on temporaryrepairs, see page
.)
82
184
05/06/09 16:03:39 31MBZ610_152
144
Tire Replacement
Tires
Servicing Your Honda
Saf ety Precautions
A permanent repair, such as an internalplug patch, can be made if a tire has only asmall puncture in the tread area. With sucha repair, you should not exceed 50 mph(80 km/h) for the first 24 hours, or 80 mph(130 km/h) at any time thereafter. Inaddition, you may not be able to safelycarry as much weight. If you choose tohave a tire repaired, be sure the repairwork is performed by a professional andthat the wheel is balanced before you ride.
Refer to on page .
The tires that came on your motorcyclewere designed to match the performancecapabilities of your motorcycle andprovide the best combination of handling,braking, durability, and comfort.
If you have a tire professionally repairedat a non-Honda facility, we recommendthat you have the work checked by yourHonda dealer.
82
05/06/09 16:03:45 31MBZ610_153
120/70 ZR17M/C (58W)
BRIDGESTONEBT-56R RADIAL G
180/55 ZR17M/C (73W)
BRIDGESTONEBT-56F RADIAL N
MICHELINPilot ROAD S
MICHELINPilot ROAD S
radial, tubeless
Installing improper tires on yourmotorcycle can affect handlingand stability. This can cause acrash in which you can beseriously hurt or killed.
Always use the size and type oftires recommended in this owner’smanual.
front
rear
type
145
Tires
Servicing Your Honda
The recommended tires for yourmotorcycle are:
You should replace the tires with tires ofthe same size, load range, and speed ratingas the originals.
Have the tire replaced by your Hondadealer if possible.
Have the wheel balanced after the tire isinstalled.
Whenever you replace a tire, remember:
05/06/09 16:03:54 31MBZ610_154
146
Tires
Servicing Your Honda
Do not install a bias-ply tire on thismotorcycle. Mixing bias-ply and radialtires can adversely affect handling andstability.
Use only tubeless tires on thismotorcycle. The rims are designed fortubeless tires, and during hardacceleration or braking, a tube-type tirecould slip on the rim and cause the tireto rapidly deflate.
Do not install a tube inside a tubelesstire on this motorcycle. Excessive heatbuild-up can cause the tube to burst.
Important Safety Reminders
If you have a tire professionally replacedat a non-Honda facility, we recommendthat you have the work checked by yourHonda dealer.
05/06/09 16:04:00 31MBZ610_155
LEFT SIDE
(1) side stand spring
(1)
147
Side Stand
Servicing Your Honda
Saf ety PrecautionsRefer to on page . Check the spring for damage or loss oftension.Check the side stand ignition cut-offsystem:
Sit astride the motorcycle and put thetransmission in neutral.Raise the side stand.Start the engine.Pull the clutch lever in.Shift the transmission into gear.Lower the side stand all the way.
The engine should stop as you lower theside stand. If the engine doesn’t stop,see your Honda dealer for service.
Check that the side stand assembly isworking properly. If the side stand isstiff or squeaky, clean the pivot areaand lubricate the pivot bolt with cleangrease.
1.
2.3.4.5.6.
82
05/06/09 16:04:11 31MBZ610_156
148
Drive Chain
Servicing Your Honda
An endless (riveted master link) chainconnects the countershaft and rear wheelsprockets. The O-ring chain uses rubberrings between the side plates of the pinand roller links to seal in themanufacturer-installed lubricating greaseand keep out moisture and dirt.
Under severe usage, or when themotorcycle is ridden in unusually dusty ormuddy areas, more frequent maintenancewill be necessary.
The service life of the chain depends onproper lubrication and adjustment. Poormaintenance can cause premature wear ordamage to the drive chain or sprockets.
The drive chain should be checked,adjusted, and lubricated as part of the pre-ride inspection (page ).
Before servicing your drive chain, turn theengine OFF, lower the side stand, andcheck that your transmission is in neutral.
It is not necessary to remove or replace thedrive chain to perform the recommendedservice in the Maintenance Schedule.
51
05/06/09 16:04:17 31MBZ610_157
- -1 3/16 1 9/16 in (30 40 mm)
LEFT SIDE
(1) drive chain
(1)
149
Inspection
Drive Chain
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Check slack in the lower drive chain( ) run midway between the sprockets.Drive chain slack should allow thefollowing vertical movement by hand:
Check drive chain slack at severalpoints along the chain. The slack shouldremain constant. If it isn’t, some linksmay be kinked and binding. Lubricatingthe chain will often eliminate bindingand kinking.Inspect the drive chain for:
damaged rollersdry or rusted linkskinked or binding links
excessive wearimproper adjustmentdamaged or missing O-rings
(cont’d)
1.
2.
3.
1
82
05/06/09 16:04:25 31MBZ610_158
wornsprocketteeth
REPLACE
damagedsprocketteeth
REPLACE
normal sprocket teethGOOD
150
Drive Chain
Servicing Your Honda
Use of a new chain with worn sprocketswill cause rapid chain wear.
Inspect the front and rear sprocket teethfor excessive wear or damage. Ifnecessary, have your Honda dealerreplace a worn sprocket.
Replace the drive chain (page ) if ithas damaged rollers, loose pins, orkinks that cannot be freed. Lubricate thedrive chain (page ) if it appears dryor shows signs of rust. Lubricate anykinked or binding links and work themfree. Adjust chain slack if needed.
4.
154
153
05/06/09 16:04:30 31MBZ610_159
- -1 3/16 1 9/16 in (30 40 mm)
1 15/16 in (50 mm)
LEFT SIDE
(2) red zone (3) index line
(3)(2)
151
Adjustment
Drive Chain
Servicing Your Honda
Saf ety Precautions
Wear Inspection The bottom part of the frame may bedamaged by excessive drive chain slack ofmore than:
Drive chain slack should be checked andadjusted, if necessary, every 500 miles(800 km). When operated at sustainedhigh speeds or under conditions offrequent rapid acceleration, the chain mayrequire more frequent adjustments.
Refer to on page .
Check the chain wear label when adjustingthe chain. If the red zone ( ) on the labelaligns with the index lines ( ) on bothsides of the swingarm after the chain hasbeen adjusted to the proper slack, thechain is excessively worn and must bereplaced. The proper slack is:
(cont’d)
23
82
05/06/09 16:04:41 31MBZ610_160
- -1 3/16 1 9/16 in (30 40 mm)
(3)
(2)
(1)
(4) (5)RIGHT SIDE
(1) axle nut(2) lock nut(3) drive chain
adjusting nut
(4) index marks(5) index lines
152
Drive Chain
Servicing Your Honda
Loosen the axle nut ( ).
Place the motorcycle on its side standwith the transmission in neutral and theignition switch OFF.
Loosen the lock nuts ( ) on both sidesof the swingarm.Turn both adjusting nuts ( ) an equalnumber of turns until the correct drivechain slack is obtained. Turn theadjusting nuts clockwise to tighten thechain, or counterclockwise to providemore slack. Adjust the chain slack at apoint midway between the drivesprocket and the rear wheel sprocket.Roll the motorcycle forward. Stop andplace it on its side stand. Recheck chainslack. Chain slack should allow thefollowing vertical movement by hand:
1.
2.
3.
1
4.
2
3
05/06/09 16:04:49 31MBZ610_161
SAE 80 or 90 gear oil
65 lbf·ft (88 N·m , 9.0 kgf·m)
153
Lubrication
Drive Chain
Servicing Your Honda
Saf ety Precautions
Lubricate every 500 miles (800 km) orsooner if chain appears dry. Lubricant:
Check rear axle alignment by makingsure the chain adjuster index marks ( )align with the index lines ( ) on bothsides of the swingarm.Both marks should correspond. If theaxle is misaligned, turn the right or leftadjusting nuts until the marks arealigned and recheck chain slack.Torque the rear axle nut to:
If a torque wrench is not used for thisinstallation, see your Honda dealer assoon as possible to verify properassembly. Improper assembly may leadto a loss of braking capacity.Tighten the adjusting nuts lightly. Then,while holding the adjusting nuts with awrench, tighten the lock nuts.
Recheck drive chain slack (page ).
Refer to on page .
(cont’d)
5.
6.
7.
8. 149
82
45
05/06/09 16:04:58 31MBZ610_162
-
D.I.D. 525VM2
RK 525ROor
154
Removal, Cleaning &Replacement
Drive Chain
Servicing Your Honda
Saf ety Precautions
Lubricate only with SAE 80 or 90 gear oil.Commercial chain lubricants may containsolvents which could damage the rubberO-rings.
Refer to on page .
Your motorcycle has an endless (rivetedmaster link) type chain. It should only beremoved or replaced by your Honda dealer.
The O-rings can be damaged by steamcleaning, high pressure washers, andcertain solvents.
Clean the side surfaces of the chainwith a dry cloth. Use a high flashpointsolvent such as kerosene notgasoline.Do not brush the rubber O-rings.Brushing will damage them. Use of asolvent may also damage the O-rings.Inspect the drive chain for possiblewear or damage.
Replace the drive chain if it has damagedrollers, loose fitting links, damagedO-rings, or otherwise appearsunserviceable.Replacement Chain:
1.
2.82
05/06/09 16:05:07 31MBZ610_163
155
WARNING:
Wash hands after handling.
Battery
Servicing Your Honda
Your battery is a maintenance-f ree typeand can be permanently damaged if thecap strip is removed.
Battery Charging,
Battery Storage,
Your motorcycle has a maintenance-freetype battery. You do not have to check thebattery electrolyte level or add distilledwater as you would with a conventional-type battery.
If you do not expect to ride yourmotorcycle for at least two weeks, werecommend you remove the battery –– orat least disconnect the battery cables(negative cable first).
Electrical accessories use current from thebattery –– even when the ignition is OFF.Limited operation also allows the batteryto discharge. If you have electricalaccessories on your motorcycle –– or donot ride frequently, we recommend thatyou charge the battery frequently (see
page ).
If you plan to store your motorcycle, seepage .
If your battery seems weak and/or isleaking electrolyte (causing slow startingor other electrical problems), see yourHonda dealer.
Battery posts, terminals andrelated accessories contain lead and leadcompounds.
156
159
05/06/09 16:05:14 31MBZ610_164
The battery gives off explosivehydrogen gas during normaloperation.
A spark or flame can cause thebattery to explode with enoughforce to kill or seriously hurt you.
Wear protective clothing and aface shield, or have a skilledmechanic do the batterymaintenance.
156
Battery Storage
Battery
Servicing Your Honda
Saf ety Precautions
BatteryCharging,
Refer to on page .
If you plan to store your motorcycle, werecommend you remove the battery andstore it where it can be charged at leastevery 30 days to maintain its service life.
If you do not remove the battery, werecommend disconnecting the batterycables (negative cable first).
You will get the best storage results fromremoving the battery and slow (trickle)charging it every 30 days (see
page ).
Before you remove the battery, be sure toread all the information that follows, aswell as the information on the batterylabel.82
159
05/06/09 16:05:20 31MBZ610_165
-
+
-+
(1)(2)
(3)(4)
RIGHT SIDE
(6)
(1) strap(2) hook
(3) battery(4) battery box(5) negative ( ) terminal lead(6) positive ( ) terminal lead
(5)
(3)
157
Battery
Servicing Your Honda
The battery is in the battery box behind theright side cover.
RemovalMake sure the ignition switch is OFF.Remove the seat (page ).Remove the right side cover (page ).Unhook the strap ( ) and remove thepositive cable from the hook ( )securing it.Pull the battery ( ) out of the batterybox ( ).Disconnect the negative ( ) terminallead ( ) from the battery first, thendisconnect the positive ( ) terminallead ( ).
(cont’d)
3.4.
1.2.1.
5.
6.
9899
12
34
6
5
05/06/09 16:05:31 31MBZ610_166
+-
158
Battery
Servicing Your Honda
Charge the battery (see followingsection), unless you have been ridingregularly.Store your battery in an easy-to-reachlocation off the floor, in an areaprotected from freezing temperaturesand direct sunlight.Clean the battery box after removingthe battery for storage. Dry the batterybox and, if paint is missing, re-paint thearea.Slow charge the battery (see followingsection) once every 30 days.
InstallationReinstall in the reverse order of removal.Be sure to connect the positive ( )terminal first, then the negative ( )terminal.Check all bolts and other fasteners aresecure.
7.
8.
9.
10.
1.
2.
05/06/09 16:05:38 31MBZ610_167
(1) ‘‘trickle’’ charger
(1)
159
Battery Charging
Battery
Servicing Your Honda
Saf ety Precautions
We recommend using a ‘‘trickle’’ charger( ) for home charging. These units can beleft connected for long periods withoutrisking damage to the battery. However,do not intentionally leave the chargerconnected longer than the time periodrecommended in the charger’s instructions.
Avoid using an automotive-type batterycharger. An automotive charger canoverheat a motorcycle battery and causepermanent damage.
Refer to on page .
Be sure to read the information that camewith your battery charger and follow theinstructions on the battery. Impropercharging may damage the battery.
1
82
05/06/09 16:05:44 31MBZ610_168
---
-
160
General Recommendations
Appearance Care
Servicing Your Honda
Saf ety Precautions
Frequent cleaning and polishing will keepyour Honda looking newer longer.Frequent cleaning also identifies you as anowner who values your motorcycle. Aclean motorcycle is also easier to inspectand service.
Refer to on page .
To clean your motorcycle, you may use:watera mild, neutral detergent and watera mild spray and wipe cleaner/polishera mild spray and rinse cleaner/degreaser and water
Avoid products that contain harshdetergents or chemical solvents thatcould damage the metal, paint, andplastic on your motorcycle.If your motorcycle is still warm fromrecent operation, give the engine andexhaust system time to cool off.Park in a shady area. Washing yourmotorcycle in bright sunlight may causethe finish to fade because water dropletsintensify the sun’s brightness. Spottingis also more likely because surfacewater can dry before you have time towipe it off.Clean your motorcycle regularly toprotect surface finishes.
82
05/06/09 16:05:55 31MBZ610_169
161
Appearance Care
Servicing Your Honda
High pressure water (or air) can damagecertain parts of your motorcycle.
We recommend the use of a gardenhose to wash your motorcycle. Highpressure washers (like those at coin-operated car washes) can damagecertain parts of your motorcycle.
After cleaning, inspect for damage,wear, and leaks (fuel, oil, coolant, andbrake fluid).
05/06/09 16:05:59 31MBZ610_170
162
Washing Your Motorcycle with aMild Detergent
Appearance Care
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Rinse your motorcycle thoroughly withcool water to remove loose dirt.Fill a bucket with cool water. Mix in amild, neutral detergent, such as dishwashing liquid or a product madeespecially for washing motorcycles orautomobiles.Wash your motorcycle with a sponge ora soft towel. As you wash, check forheavy grime. If necessary, use a mildcleaner/degreaser to remove the grime.
Clean the headlight and other plasticparts using a cloth or sponge dampenedwith a solution of mild detergent andwater. When cleaning the plasticheadlight lens, use more care because itwill scratch easier than a glass lens. Rubany soiled area, gently rinsing itfrequently with fresh water.
If the inside of the headlight lensappears clouded immediately afterwashing, it should clear after a fewminutes of riding.
1.
2.
3.
4.
82
05/06/09 16:06:06 31MBZ610_171
163
Appearance Care
Servicing Your Honda
After washing, rinse your motorcyclethoroughly with plenty of clean water toremove any residue. Detergent residuecan corrode alloy parts.Dry your motorcycle with a chamois ora soft towel. Leaving water on thesurface to air dry can cause dulling andwater spots. As you dry, inspect forchips and scratches.
As a precaution, ride your motorcycle ata slow speed and apply the brakesseveral times. This will help dry thebrakes and restore normal brakingperformance.
Start the engine and let it idle forseveral minutes. The engine heat willhelp dry moist areas.
Lubricate the drive chain to preventrusting.
5.
6.
7.
8.
9.
05/06/09 16:06:11 31MBZ610_172
164
Clean the Matte Painted Surface Spray Cleaning Your Motorcycle
Appearance Care
Servicing Your Honda
Saf ety PrecautionsSaf ety Precautions
Suggestions for using spray cleaner(s)follow:
Avoid using spray cleaner products on thetires or suspension components.
Refer to on page .Refer to on page .
Use a soft cloth or sponge, plenty of water,and a mild detergent to clean the mattepaint. Dry with a soft, clean cloth.
Do not use polishing compounds or waxcontaining polishing compounds. Thesecan damage or discolor the paint.
To keep your Honda looking new, cleanand polish it frequently.
82 82
05/06/09 16:06:19 31MBZ610_173
Apply a spray cleaner/polish and wipe thepaint, chrome, glass, and clear plastic.
Dust and fingerprint smudges.
Light road grime. Spray any difficult-to-reach or very dirtyareas with a spray cleaner/degreaser.Rinse and dry.Apply a spray cleaner/polish and wipe witha non-abrasive cloth.Use a spray cleaner/degreaser.If necessary, rub with a sponge. Rinse anddry.Apply a spray cleaner/polish and wipe witha non-abrasive cloth.Apply a high quality chrome/aluminumpolish and wipe with a non-abrasive cloth.
Heavy grime. Oil leaks. Brakedust.
Dull, corroded chrome oraluminum.
Recommended CleaningMotorcycle Condition
165
Appearance Care
Servicing Your Honda
05/06/09 16:06:28 31MBZ610_174
166
Painted Aluminum WheelMaintenance
Appearance Care
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
Aluminum may corrode from contact withdirt, mud, or road salt. Clean the wheelsafter riding through any of thesesubstances. Use a wet sponge and milddetergent. Avoid stiff brushes, steel wool,or cleaners containing abrasives orchemical compounds.
After washing, rinse with plenty of waterand dry with a clean cloth.
If the paint is chipped, apply touch-uppaint.
82
05/06/09 16:06:33 31MBZ610_175
167
Finishing Touches
Appearance Care
Servicing Your Honda
Saf ety PrecautionsRefer to on page .
After washing your motorcycle, considerusing a commercially-available spraycleaner/polish or quality liquid or pastewax to finish the job. Use only a non-abrasive polish or wax made specificallyfor motorcycles or automobiles. Apply thepolish or wax according to the instructionson the container.
If a surface on your motorcycle is chippedor scratched, your Honda dealer has touch-up paint to match your motorcycle’s color.Be sure to use your motorcycle’s colorcode (page ) when you buy touch-uppaint.
If the frame has a chip that exposes themetal, first apply primer (to preventcorrosion) and then apply the touch-uppaint. Several thin layers of touch-up paintare better than one thick coat.
82
210
05/06/09 16:06:38 31MBZ610_176
168 Servicing Your Honda
05/06/09 16:06:41 31MBZ610_177
169
Tips
Tips
Here’s a few helpful tips on how to storeand transport your Honda, and how to bean environmentally responsiblemotorcycle owner.
............................Storing Your Honda . 170...........Transporting Your Motorcycle . 174
......................You & the Environment . 175
05/06/09 16:06:44 31MBZ610_178
170
Preparation for Storage
Storing Your Honda
Tips
Saf ety Precautions
Honda Motorcycle Winter StorageGuide,
If you won’t be riding for an extendedperiod, such as during the winter,thoroughly inspect your motorcycle andcorrect any problem before storing it. Thatway, needed repairs won’t be forgottenand it will be easier to get your motorcyclerunning again.
Refer to on page .
This procedure requires a means fordraining and disposing of drained fuel(page ).
Change the engine oil and filter (page).
Make sure the cooling system is filledwith a 50/50% antifreeze solution (page
).Fill the fuel tank. Make sure the fuel fillcap is properly installed.
We suggest you perform the followingprocedures to keep your motorcycle in topcondition. These storage procedures willreduce the deterioration that can occurduring storage.
For more information about storage, referto the
available from your Honda dealer(USA only).
1.
2.
3.
82
175
108
113
05/06/09 16:06:52 31MBZ610_179
-Gasoline is highly flammable andexplosive. You can be burned orseriously injured when handlingfuel.
Stop the engine and keep heat,sparks and flame away.Handle fuel only outdoors.Wipe up spills immediately.
171
Storing Your Honda
Tips
(cont’d)
To prevent rusting in the cylinders,perform the following:
Remove the spark plug caps from thespark plugs. Using tape or string,secure the caps to any convenientplastic body part so that they arepositioned away from the spark plugs.Remove the spark plugs from theengine and store them in a safe place.Do not connect the spark plugs to thespark plug caps.Pour a tablespoon (15 20 cc) ofclean engine oil into each cylinderand cover the spark plug holes with apiece of cloth.
Drain the carburetors into an approvedgasoline container and dispose of it inan approved manner (page ).If storage will last longer than onemonth, carburetor draining is important,to assure proper performance afterstorage.
4. 5.
175
05/06/09 16:07:00 31MBZ610_180
172
Storing Your Honda
Tips
With the engine stop switch in theRUN position, press the start buttonseveral times to crank the engine anddistribute the oil.Reinstall the spark plugs and sparkplug caps.
Remove the battery and charge it fully.Store it in an area protected fromfreezing temperatures and directsunlight. Slow charge the battery (page
) once a month.Wash and dry your motorcycle. Waxall painted surfaces. Apply rust-inhibiting oil to the chrome pieces.Lubricate the drive chain (page ).Inflate the tires to their recommendedpressures (page ).
Store your motorcycle in an unheatedarea, free of dampness, away fromsunlight, with a minimum of dailytemperature variation.Place your motorcycle on blocks to liftboth tires off the floor.Cover your motorcycle with a porousmaterial. Avoid using plastic or similarnon-breathing, coated materials thatrestrict air flow and allow heat andmoisture to accumulate.
6.
7.
8.9.
10.
11.
12.
159
153
140
05/06/09 16:07:08 31MBZ610_181
173
Removal from Storage
Tips
Storing Your Honda
Saf ety PrecautionsRefer to on page .
Uncover and clean your motorcycle.If your motorcycle has been stored formore than four months –– change theengine oil (page ).If your motorcycle has been stored formore than two months –– ask yourHonda dealer to drain and replace thefuel.Charge the battery (page ) asrequired. Install the battery.Lubricate the drive chain (page ).Perform a pre-ride inspection (page ),then test-ride your motorcycle at lowspeeds.
1.2.
3.
4.
5.6.
82
108
159
15351
05/06/09 16:07:16 31MBZ610_182
174
Transporting Your Motorcycle
Tips
If your motorcycle needs to be transported,it should be carried on a motorcycle trailer,or a truck or trailer with a flatbed area. Forinformation about 24-hour emergencyassistance, see page (USA only). Donot tow your motorcycle, as towing canseriously damage the transmission.
When contacting a towing or transportingservice, be sure to ask if they have aflatbed area, a loading ramp or powerramp to safely lift the motorcycle, andmotorcycle tie-down straps.
237
05/06/09 16:07:20 31MBZ610_183
175
You & the Environment
Tips
Choose Sensible Cleaners.
Recycle Wastes.Owning and riding a motorcycle can beenjoyable, but you must do your part toprotect nature.
Following are tips on how you can be anenvironmentally-responsible motorcycleowner.
Use abiodegradable detergent when you washyour motorcycle. Avoid aerosol spraycleaners that containchlorofluorocarbons (CFCs) whichdamage the atmosphere’s protectiveozone layer. Don’t throw cleaningsolvents away; see the followingguidelines for proper disposal.
It’s illegal andthoughtless to put used engine oil in thetrash, down a drain, or on the ground.Used oil, gasoline, coolant, andcleaning solvents contain poisons thatcan hurt refuse workers andcontaminate our drinking water, lakes,rivers, and oceans. Before changingyour oil, make sure you have the propercontainers. Put oil and other toxicwastes in separate sealed containers andtake them to a recycling center. Callyour local or state office of publicworks or environmental services to finda recycling center in your area, and toget instructions on how to dispose ofnon-recyclable wastes.
05/06/09 16:07:25 31MBZ610_184
176 Tips
05/06/09 16:07:27 31MBZ610_185
177
Taking Care of the Unexpected
Taking Care of the Unexpected
This section discusses the more commonproblems that can occur with yourmotorcycle while you’re riding. It tellsyou how to evaluate each problem andwhat actions you can take to try to resumeriding. If the problem cannot be safelysolved, this section also gives instructionson the proper way to have yourmotorcycle transported.
For information about transporting yourmotorcycle, see page .
..............................General Guidelines . 178If Your Engine Quits or
..........................................Won’t Start . 179.......................If You Have a Flat Tire . 184
...................If Your Engine Overheats . 196If the Low Oil Pressure Indicator
.....................................................lights . 198....................................If a Fuse Blows . 199
........................................If You Crash . 203........................If You Lose Your Key . 204
.......If Your Battery Is Low (or Dead) . 205174
05/06/09 16:07:33 31MBZ610_186
178
General Guidelines
Taking Care of the Unexpected
Taking Care of the Unexpected
Remember to take along your owner’smanual, the tool kit that came with yourmotorcycle, and any other items (such astire repair supplies and additional tools)that might help you solve a problem onyour own.
Should you ever have a problem whileriding, please follow these guidelines:
Always put personal safety first.Take time to assess the situation andyour options before deciding what to do.If the problem is relatively minor andyou have the tools, supplies, and skillsto make a temporary repair, be sure tohave permanent repairs made as soon aspossible.Do not continue riding if you are hurt oryour motorcycle is not in safe ridingcondition.
Additional recommendations for specificproblems follow.
Keeping your motorcycle well-maintainedis the best way to reduce the possibility ofhaving a problem on the road. However,since problems can arise even with well-maintained machines, you may considersubscribing to an emergency roadsideservice plan. (USA only: For informationabout the Honda Rider’s Club of America,see page .)237
05/06/09 16:07:41 31MBZ610_187
--
179
If Your Engine Quits or Won’t Start
Taking Care of the Unexpected
Starter motor doesn’t operate
Starter motor works,but the engine won’t start
Proper operation and maintenance canprevent starting and engine performanceproblems. In many cases, the cause of theproblem may be a simple operationaloversight.
If you have a problem starting theengine or experience poor engineperformance the following informationmay help you. If you can’t correct theproblem, see your Honda dealer.
If your motorcycle won’t start, listen asyou press the start button. If you don’thear the starter motor turning, refer to the
symptom. Ifyou can hear the starter motor workingnormally, refer to the
symptom.
05/06/09 16:07:45 31MBZ610_188
SYMPTOM:WHAT TO DOPOSSIBLE CAUSE
ignition switch OFFengine stop switch OFFtransmission not in neutral
blown fuse
battery lead loose
side stand down (whentransmission not in neutral)
dead battery
faulty starter motor
Turn the ignition switch ON.Turn the engine stop switch to RUN.Shift into neutral.Put the transmission in neutral or raise the sidestand and pull the clutch lever in.
Replace with a new fuse of the same rating (page).
Tighten the battery lead.Charge the battery (page ). If charging doesn’thelp, see your Honda dealer.If all possible causes are negative, the startermotor may be faulty. See your Honda dealer.
199
159
Starter motor doesn’t operate.
180
If Your Engine Quits or Won’t Start
Taking Care of the Unexpected
05/06/09 16:07:58 31MBZ610_189
WHAT TO DOPOSSIBLE CAUSESYMPTOM:
out of fuelflooded engine
Fill the fuel tank.See (page ).
loose or unconnected sparkplug caps
Install the spark plug caps securely. If the enginestill won’t start, see your Honda dealer.Tighten the battery terminal bolts.loose battery cables
weak battery Charge the battery (page ). If charging doesn’thelp, see your Honda dealer.
64
159
Starter motor works, but the engine won’t start.
Flooded Engine
181
If Your Engine Quits or Won’t Start
Taking Care of the Unexpected
05/06/09 16:08:07 31MBZ610_190
WHAT TO DOPOSSIBLE CAUSESYMPTOM:
Raise the side stand. Start again.
SYMPTOM:
idles roughly, too fast, stalls
low oil pressure
overheating
Check engine idle adjustment (page ). If theproblem persists, see your Honda dealer.
POSSIBLE CAUSE WHAT TO DO
side stand down
See your Honda dealer.blubbers (rich fuel mixture)runs erratically, misfires See your Honda dealer.
Check the low oil pressure indicator. Refer topage
.
Check the coolant temperature meter. Refer topage .
125
196
198
Engine starts, but stalls as you shift into gear.
Engine starts, but runs poorly.
Ifthe Low Oil Pressure Indicator Lights,
IfY our Engine Overheats,
182
If Your Engine Quits or Won’t Start
Taking Care of the Unexpected
05/06/09 16:08:21 31MBZ610_191
WHAT TO DOPOSSIBLE CAUSESYMPTOM:
sooty exhaust (rich fuelmixture)
pre-ignition (runs on afterignition switched OFF)
detonates or pings underload
afterfires (backfires)
See your Honda dealer.
If applicable, switch to the recommended octanegasoline (page ) or change your brand ofgasoline. If the problem persists, see your Hondadealer.See your Honda dealer.See your Honda dealer.
100
Engine starts, but runs poorly. (cont’d)
183
If Your Engine Quits or Won’t Start
Taking Care of the Unexpected
05/06/09 16:08:29 31MBZ610_192
184
If You Have a Flat Tire
Taking Care of the Unexpected
A flat tire is always unwelcome,especially if you are far from help. If youthink you are losing air, or you hit apothole or hard object, pull safely to theside of the road so you can inspect thetires and assess the situation. (Be sure topark on a firm, level surface and use theside stand for support.) You shouldexamine the tire treads and sidewalls forforeign objects or damage. If you find atire that has been punctured or damaged,you have two options.
Option 1:Have Your Motorcycle TransportedIf a tire has a major puncture or a cut inthe tread or sidewall, or the bead has comeloose from the rim, there is probably notmuch you can do except have yourmotorcycle transported to a Honda dealer
or other qualified service facility. (USAonly: For information about 24-houremergency roadside assistance, see page
.) Even with a simple puncture, thismay be the safest and least troublesomesolution. For transporting instructions, seepage .
Option 2:Make a Temporary Roadside RepairIf a tire has only a minor nail puncture andis not completely flat, you may be able tomake an emergency repair that couldallow you to continue riding to where youcan get the tire replaced or permanentlyrepaired.
237
174
05/06/09 16:08:35 31MBZ610_193
Riding your motorcycle with atemporary tire repair can be risky.If the temporary repair fails, youcan crash and be seriously injuredor killed.
If you must ride with a temporarytire repair, ride slowly andcarefully and do not exceed 30mph (50 km/h) until the tire ispermanently repaired or replaced.
185
Types of Temporary Repairs
If You Have a Flat Tire
Taking Care of the Unexpected
Due to the uncertainty of any temporaryrepair, you should ride slowly (not over30 mph, 50 km/h) and carefully(preferably without a passenger or cargo)until the tire is replaced or permanently
repaired. Stop frequently and check the airpressure. If the tire is losing pressure, itmay be unsafe to continue riding. As thetire gets low, it will affect the handling ofyour motorcycle (especially with apassenger and cargo) and it may overheatand blow out.
The following types of temporary repairsgenerally require a source of air to inflatethe tire. Possible sources include COcartridges or cans of compressed airdesigned to inflate a tire.
(cont’d)
2
05/06/09 16:08:40 31MBZ610_194
186
Should You Repair or Replace aTire?
If You Have a Flat Tire
Taking Care of the Unexpected
Inflate the tire:
Plug the hole:
Tubeless tires havesome self-sealing ability if they arepunctured and the result is usually just aslow leak. If this is the case, you can tryinflating the tire to see if it will hold airpressure. If you can see a nail or otherobject embedded in the tire tread, do notremove it at this time.
The idea here is to dosomething to temporarily stop the leak.If you have a tubeless tire repair kit,you can pull out the nail and tryinserting an external plug in thepuncture. Follow the instructions thatcame with the repair kit and be sure toinflate the tire to the correct pressure.
We strongly recommend that you replace,not permanently repair, any tire that ispunctured or damaged, even if the tire hasonly a minor puncture. For a fulldiscussion of repairs and replacement, seepage .143
05/06/09 16:08:46 31MBZ610_195
(1) fixing bolts(2) brake caliper assembly
(2)(1)
LEFT SIDE
187
Emergency Front WheelRemoval/Installation
If You Have a Flat Tire
Taking Care of the Unexpected
Saf ety PrecautionsRefer to on page .
(cont’d)
We recommend wheel removal be doneonly by your Honda dealer or anotherqualified mechanic. Do not attempt toremove the wheel on your own. Wheelremoval requires mechanical skill andprofessional tools.
RemovalPark your motorcycle on a firm, levelsurface.Raise the front wheel off the ground byplacing a support block under theengine.
Remove the fixing bolts ( ) andremove the right and left caliperassemblies ( ) from the fork legs.
1.
82
2.
3.
2
1
05/06/09 16:08:55 31MBZ610_196
RIGHT FRONT
(4) (3)
(3) axle pinch bolts(4) axle bolt
188
If You Have a Flat Tire
Taking Care of the Unexpected
To avoid damage to the brake hoseduring removal, support the caliperassembly so that it doesn’t hang fromthe hose. Do not twist the brake hose.Avoid getting grease, oil, or dirt on thedisc or pad surfaces. Any contaminationcan cause poor brake performance orrapid pad wear after reassembly.Avoid depressing the brake lever whenthe caliper is off the motorcycle. Thiswill force the caliper pistons out of thecylinders. The result will be loss ofbrake fluid. If this occurs, the brakesystem will require service. See yourHonda dealer for this service.
Loosen the right and left axle pinchbolts ( ) and remove the front axle bolt( ).
4.
43
05/06/09 16:09:01 31MBZ610_197
LEFT FRONT
(5)
(3)
(5) front axle shaft
189
If You Have a Flat Tire
Taking Care of the Unexpected
Remove the front axle ( ) and thewheel.
5. 5
05/06/09 16:09:05 31MBZ610_198
16 lbf·ft (22 N·m , 2.2 kgf·m)
43 lbf·ft (59 N·m , 6.0 kgf·m)
22 lbf·ft (30 N·m , 3.1 kgf·m)
(6) index line(7) surface
LEFT FRONT (6)
(7)
190
If You Have a Flat Tire
Taking Care of the Unexpected
Position the wheel between the forklegs and insert the front axle shaft fromthe left side, through the left fork legand wheel hub.Align the index line ( ) of the frontaxle shaft with the recessed surface ( )of the fork leg.
Installation
Tighten the front axle bolt to thespecified torque:
Install the brake caliper assemblies ontothe fork legs.To avoid damaging the brake padswhile installing the brake caliperassembly, carefully fit the brake discbetween the pads.Install the caliper fixing bolts andtighten to the specified torque:
Tighten the front axle pinch bolt on theleft fork leg to the specified torque:1.
67
3.
4.
6.
5.2.
05/06/09 16:09:15 31MBZ610_199
16 lbf·ft (22 N·m , 2.2 kgf·m)
(8) brake disc (9) brake bracket
(8)
(9)(9)
191
If You Have a Flat Tire
Taking Care of the Unexpected
If a torque wrench was not used forinstallation, see your Honda dealer as soonas possible to verify proper assembly.Improper assembly may lead to loss ofbraking capability.
Tighten the front axle pinch bolt on theright fork leg to the specified torque:
Operate the front brake and pump thefork several times. Check for freewheel rotation after the brake isreleased. Recheck the wheel if the brakedrags or the wheel does not rotate freely.
Visually check that the clearancesbetween each surface of the brakedisc and the brake bracket (not brakepads) are symmetrical.
7.
8.
05/06/09 16:09:23 31MBZ610_200
RIGHT REAR
(2)
(1)
(2) lock nut
(3)
(1) rear axle nut (3) adjusting nut
192
Emergency Rear WheelRemoval/Installation
If You Have a Flat Tire
Taking Care of the Unexpected
Saf ety PrecautionsRefer to on page .
Loosen the rear axle nut ( ).
Park your motorcycle on a firm, levelsurface.Raise the rear wheel off the ground byplacing a support block under theengine.
Remove the rear axle nut.
Removal
We recommend wheel removal be doneonly by your Honda dealer or anotherqualified mechanic. Do not attempt toremove the wheel on your own. Wheelremoval requires mechanical skill andprofessional tools.
Loosen the lock nuts ( ) and drivechain adjusting nuts ( ) on both sidesof the swingarm.
3.4.
5.
1.
2.
1
82
23
05/06/09 16:09:32 31MBZ610_201
LEFT REAR
(5)(4)
(4) drive chain (5) rear axle shaft
193
If You Have a Flat Tire
Taking Care of the Unexpected
Remove the drive chain ( ) from therear sprocket by pushing the rear wheelforward.
Remove the rear axle shaft ( ), rearwheel and side collars from theswingarm.
To avoid damage to the brake hoseduring removal, support the caliperassembly so that it doesn’t hang fromthe hose. Do not twist the brake hose.Avoid depressing the brake pedal whenthe wheel is off the motorcycle. Thiswill force the caliper piston out of thecylinder. The result will be a loss ofbrake fluid. If this occurs, the brakesystem will require service.See your Honda dealer for this service.
6.
7.
4
5
05/06/09 16:09:38 31MBZ610_202
RIGHT REAR
(6)
(7)
(8)
(6) lug(7) slot
(8) swingarm
194
If You Have a Flat Tire
Taking Care of the Unexpected
InstallationApply the multi-purpose grease to theinside of the side collars and install theside collars into the rear wheel.
Avoid getting grease, oil, or dirt onthe disc or pad surfaces. Anycontamination can cause poor brakeperformance or rapid pad wear afterreassembly.
Reinstall the brake caliper holder ontothe swingarm.
Make sure that the lug ( ) on thebrake caliper holder is located in theslot ( ) on the swingarm ( ).
1.
2.
6
7 8
05/06/09 16:09:45 31MBZ610_203
65 lbf·ft (88 N·m , 9.0 kgf·m)
195
If You Have a Flat Tire
Taking Care of the Unexpected
After installing the wheel, apply thebrake pedal several times, then recheckthe disc for caliper holder to discclearance. Do not operate themotorcycle without adequate clearance.
If a torque wrench was not used forinstallation, see your Honda dealer as soonas possible to verify proper assembly.Improper assembly may lead to loss ofbraking capability.
Place the rear wheel into the swingarmand install the drive chain over the rearsprocket.
While installing the wheel, carefullyfit the brake disc between the brakepads to avoid damaging the pads.
Install the rear axle shaft.Tighten the rear axle nut to thespecified torque:
Failure to provide adequate disc-to-caliper holder clearance may damagethe brake disc and impair brakingefficiency.After installing the wheel, adjust thedrive chain (page ).
7.
4.
3.
5.
6.151
05/06/09 16:09:53 31MBZ610_204
196
If Your Engine Overheats
Taking Care of the Unexpected
Continuing to ride with an overheatedengine can cause serious engine damage.
A steaming engine indicates a coolantleak. Shut the engine off and wait untilthe steaming stops. Look for a leak, butdon’t touch the engine or radiatorsystem. Let everything cool off first.
Normally, the needle on your temperaturegauge will rise to a point about midwaybetween C (cold) and H (hot) and thenlevel off. Hot weather may cause theneedle to rise higher than normal. So willtemporary stress such as climbing a hill. Ifyou’re stuck in stop-and-go traffic, theneedle may climb some, but the radiatorfan is designed to prevent overheating. Beaware of these variations as you monitorthe gauge. If there’s no obvious problem, leave the
engine on so the fan and coolantcirculating system can continueworking. Monitor the temperaturegauge. The needle may drop to thenormal range after a brief stop with noload on the engine.
If the high coolant temperature indicatorbegins to flash, and the malfunctionindicator lamp (MIL) goes on for noapparent reason, pull safely to the side ofthe road. If possible, park in a shady area.
05/06/09 16:09:59 31MBZ610_205
197
If Your Engine Overheats
Taking Care of the Unexpected
Check the radiator fan.If the fan is not working, turn theengine off. Open the fuse box (page
) and check the radiator fan fuse.If the fuse is blown, replace it with theproper (same rating) spare fuse. Startthe engine. If the malfunction indicatorlamp (MIL) goes on and high coolanttemperature indicator flashes, turn theengine off.If the radiator fan is working, visuallycheck the coolant level in the reservetank, located behind the frame (page
). It isn’t necessary to touch theradiator system.
If there’s a mild leak, you can ride forawhile, carefully watching the gauge. Beprepared to stop and add more coolant orwater. If the leak is bad, transport yourmotorcycle to a Honda dealer (page ).
If you are able to resume riding, continueto monitor the gauge frequently.
If the reserve tank is low or empty, don’tride without adding coolant (page ).After adding coolant, turn the engine onand check the temperature gauge.If the needle doesn’t drop, do not ride.
The engine needs repair. Transport yourmotorcycle to a Honda dealer (page
).If the temperature drops to normal,check the coolant level. If it has gonedown, add more coolant.
201
114
114
174
174
05/06/09 16:10:04 31MBZ610_206
198
If the Low Oil Pressure Indicator Lights
Taking Care of the Unexpected
Continuing to ride with low oil pressurecan cause serious engine damage.
Check for an oil leak.Then check the oil level. If necessary,add the recommended oil (page ) tothe upper level mark. If you must leaveyour motorcycle to get oil, secure it asmuch as possible.
If you check your engine oil levelregularly, you should never see the low oilpressure indicator and the malfunctionindicator lamp (MIL) go on while riding.Normally, both will only lightmomentarily when you turn the ignitionswitch ON. Occasionally, it may flicker ator near idling speed.
Low oil pressure may be caused by an oilleak, a low oil level, or some problem inthe engine’s lubrication system.
If the malfunction indicator lamp (MIL)lights and the low oil pressure indicatorflashes while you’re riding, don’t ignorethem. Pull safely to the side of the road. Ifpossible, pull the clutch lever in and coastto a stop. Stop the engine as soon as it’ssafe to do so.
After adding oil, start the engine, andcheck that the low oil pressure indicatorand malfunction indicator lamp (MIL)go off. Check for a possible leak.
If the indicators go off and there is noleak –– resume riding. If there is a leak–– do not ride the motorcycle until theleak is repaired by a Honda dealer.
104
05/06/09 16:10:10 31MBZ610_207
10A, 20A30A
other fusesmain fuse
199
If a Fuse Blows
Taking Care of the Unexpected
All of the electrical circuits on yourmotorcycle have fuses to protect themfrom damage caused by excess currentflow (short circuit or overload).
If something electrical on your motorcyclestops working, the first thing you shouldcheck for is a blown fuse.Determine from the chart on the circuitfuse box cover which fuse or fuses controlthat component. Check those fuses first,but check all the fuses before lookingelsewhere for another possible cause ofthe problem. Replace any blown fuses andcheck component operation.
(cont’d)
The circuit fuse box (including sparefuses) is located behind the left sidecover.
To prevent an accidental short circuit,turn the ignition switch OFF beforechecking or replacing the fuses.
Recommended Fuses
The main fuse (and spare) is located onthe starter motor magnetic switch ( )behind the right side cover.
2
1.
05/06/09 16:10:24 31MBZ610_208
(1) main fuse(2) starter magnetic switch(3) wire connector(4) spare main fuse
(4)
RIGHT SIDE
(3)
(2)
(1)
200
If a Fuse Blows
Taking Care of the Unexpected
Main Fuse Access:
Reconnect the wire connector.
The spare main fuse ( ) is located nearthe starter magnetic switch.
Disconnect the wire connector ( ) ofthe starter magnetic switch ( ).
To access the main fuse ( ), removethe right side cover (page ).
Install the right side cover.
Pull the fuse out. If the main fuse isblown, install a new main fuse.
3.
4.2.
5.
32
4
6.
199
05/06/09 16:10:34 31MBZ610_209
circuit fuse
(5) fuse box cover(6) spare fuses
LEFT SIDE
(6)
(5)
main fuse
(7) blown fuse
(7)
201
If a Fuse Blows
Taking Care of the Unexpected
Circuit Fuse Access: To check or replace a circuit fuse, pullthe old fuse out of its retaining clips.Look for a burned wire inside the fuse.If the fuse is blown ( ), replace it witha spare fuse ( ) of the same rating orlower.
Remove the left side cover (page ).Open the fuse box cover ( ).
(cont’d)
995
76
7.8.
9.
05/06/09 16:10:42 31MBZ610_210
202
If a Fuse Blows
Taking Care of the Unexpected
Replacing a f use with one that has ahigher rating greatly increases the chanceof damage to the electrical system.
If you do not have a spare fuse and youcannot ride the motorcycle without fixingthe problem, take a fuse of the same ratingor a lower rating from one of the othercircuits that you can do withouttemporarily.
If you replace a blown fuse with a sparefuse that has a lower rating, replace thefuse with the correct rating as soon as youcan. Also remember to replace any sparefuses that were installed.
If the replacement fuse of the same ratingburns out in a short time, there is probablya serious electrical problem on yourmotorcycle. Leave the blown fuse in thatcircuit and have your motorcycle checkedby your Honda dealer.
Close the fuse box cover.Install the left side cover.
If you do not have a replacement fuse withthe proper rating for the circuit, install onewith a lower rating.
10.11.
05/06/09 16:10:49 31MBZ610_211
203
If You Crash
Taking Care of the Unexpected
Transporting Your Motorcycle,
Personal safety is your first priority afterany accident. If you or anyone else hasbeen injured, take time to assess theseverity of the injuries and whether it issafe to continue riding. Call foremergency assistance if needed. Alsofollow applicable laws and regulations ifanother person or vehicle is involved inthe accident.
If you decide you are capable of ridingsafely, carefully inspect your motorcyclefor damage and determine if it is safe toride. Check the tightness of critical nutsand bolts securing such parts as thehandlebar, control levers, brakes, andwheels.
If there is minor damage, or you areunsure about possible damage, ride slowlyand cautiously. Sometimes, crash damageis hidden or not immediately apparent, soyou should have your motorcyclethoroughly checked at a qualified servicefacility as soon as possible. Also, be sureto have your Honda dealer check theframe and suspension after any seriouscrash.
If your motorcycle cannot be ridden, seepage .174
05/06/09 16:10:54 31MBZ610_212
204
If You Lose Your Key
Taking Care of the Unexpected
If you lose your key and aren’t carrying aduplicate, either get your spare or haveone made. If you don’t know your keynumber, call the dealer you purchasedyour Honda from. They may have it listedin their records. If they don’t, transportyour motorcycle to them or the nearestHonda dealer. The dealer will probablyhave to remove the ignition switchassembly to find the key number so theycan make a key for you.
Be sure to record your key number in theQuick Reference section at the rear of themanual. You’ll need this number to have aduplicate key made.
A lost key won’t be a problem if you takepreventative action. Store one duplicatekey in a safe place at home and carry asecond duplicate in your wallet.
05/06/09 16:10:58 31MBZ610_213
205Taking Care of the Unexpected
If Your Battery Is Low (or Dead)
Jump starting is not recommended,especially if you use an automobile battery.The greater amperage of an automobilebattery when the car engine is running candamage your motorcycle’s electricalsystem.
Bump starting is also not recommended.
If you can’t charge the battery or itappears unable to hold a charge, contactyour Honda dealer.
05/06/09 16:11:03 31MBZ610_214
206 Taking Care of the Unexpected
05/06/09 16:11:05 31MBZ610_215
207
Technical Information
Technical Information
This section contains dimensions,capacities, and other technical data, plusinformation on government requirementsand how to break-in your motorcycle.
..........................Vehicle Identification . 208......................................Specifications . 211
.............................Break-in Guidelines . 218High Altitude Carburetor Adjustment . 219
..................Emission Control Systems . 220.............................Catalytic Converter . 225
................................Oxygenated Fuels . 226
05/06/09 16:11:09 31MBZ610_216
(1) VIN
(1)
RIGHT SIDE
208
Serial Numbers
Vehicle Identification
Technical Information
The frame, VIN, and engine serialnumbers are required when you registeryour motorcycle. They may also berequired when ordering replacement parts.You may record these numbers in theQuick Reference section at the rear of thismanual.
The VIN (vehicle identification number)appears on the Safety Certification Labelattached to the right side of the frame.
05/06/09 16:11:14 31MBZ610_217
RIGHT SIDE
(2) frame number (3) engine number
(2)
(3)
RIGHT SIDE
209
Vehicle Identification
Technical Information
The frame number ( ) is stamped on theright side of the steering head.
The engine number ( ) is stamped on thetop of the crankcase.
2 3
05/06/09 16:11:20 31MBZ610_218
(1) color label
(1)UNDER SEAT
210
Color Label & Code
Vehicle Identification
Technical Information
The color code is helpful when orderingreplacement parts. You may record thecolor and code in the Quick Referencesection at the rear of this manual.
The color label is attached to the frameunder the seat. Remove the seat (page )to check the label.
98
05/06/09 16:11:25 31MBZ610_219
82.7 in (2,100 mm)29.1 in (740 mm)42.1 in (1,070 mm)55.9 in (1,420 mm)5.5 in (140 mm)
overall lengthoverall widthoverall heightwheelbaseground clearance
Dimensions
211
Specifications
Technical Information
05/06/09 16:11:33 31MBZ610_220
unleaded gasoline, pump octane number of 86 or higher4.49 US gal (17.0 )
4.4 US qt (4.2 )3.7 US qt (3.5 )
4.0 US qt (3.8 )
SAE 80 or 90 gear oil
2.43 US qt (2.30 )
API Service Classification SG or higher except oilslabeled as energy conserving on the circular API servicelabel, SAE 10W-40, JASO T 903 standard MA,Pro Honda GN4 or HP4 (without molybdenum additives)4-stroke oil (USA & Canada) or Honda 4-stroke oil(Canada only), or an equivalent motorcycle oil
after disassembly:after draining:
including reserve
after draining & oil filter change:
fuel recommendationfuel tank capacityengine oil capacity
engine oilrecommendation
drive chain lubricantcooling system,recommendation
Pro Honda HP Coolant or an equivalent high qualityethylene glycol antifreeze containing corrosion protectioninhibitors specifically recommended for use in aluminumengines
cooling system,capacity
Fuel & Lubricants
212
Specifications
Technical Information
05/06/09 16:11:45 31MBZ610_221
× ×
- -±
rider, passenger, all cargo and accessories
384 lbs (174 kg)392 lbs (178 kg)
36.6 cu-in (600 cm )2.56 1.78 in (65.0 45.2 mm)12.0 : 1CR9EH-9 (NGK)U27FER9 (DENSO)0.031 0.035 in (0.80 0.90 mm)1,400 100 rpm
USA :Canada :
or
operator and one passengerpassengercapacitymaximum weightcapacity
spark plug(standard)
compression ratiobore & strokedisplacement
spark plug gapidle speed
Capacities
Engine Specifications
213
Specifications
Technical Information
05/06/09 16:11:57 31MBZ610_222
1.8632.9282.0621.6471.3681.2001.0862.800
D.I.D. 525VM2 RK 525ROchain
42 teeth15 teethdrive (engine) sprocket:
driven (rear wheel) sprocket:
or
primary reductiongear ratio, 1st2nd3rd4th5th6thfinal reductionstandardsprocket sizesfinal drive
Power Transmission
214
Specifications
Technical Information
05/06/09 16:12:12 31MBZ610_223
-
25°30’3.9 in (98 mm)120/70 ZR17M/C (58W)
180/55 ZR17M/C (73W)
0.343 kW/5,000 rpm12V 6 Ah
42 psi (290 kPa , 2.90 kgf/cm )
36 psi (250 kPa , 2.50 kgf/cm )
MICHELIN Pilot ROAD SBRIDGESTONE BT-56F RADIAL N
MICHELIN Pilot ROAD SBRIDGESTONE BT-56R RADIAL Gradial, tubeless
castertrailtire size, front
tire size, rear
generatorbattery
tire pressure, rear(cold)
tire pressure, front(cold)
tire type
Chassis & Suspension
Electrical
215
Specifications
Technical Information
05/06/09 16:12:25 31MBZ610_224
-----
12V 55W12V 21/5W12V 23/8W12V 23W12V 5W
30A10A, 20A
(2 bulbs)(front)
(rear)
(2 bulbs)headlight
turn signal lightsbrake/tail light
license light
mainother fuses
Lights
Fuses
216
Specifications
Technical Information
05/06/09 16:12:35 31MBZ610_225
22 lbf·ft (29 N·m , 3.0 kgf·m)20 lbf·ft (26 N·m , 2.7 kgf·m)43 lbf·ft (59 N·m , 6.0 kgf·m)
22 lbf·ft (30 N·m , 3.1 kgf·m)
16 lbf·ft (22 N·m , 2.2 kgf·m)
65 lbf·ft (88 N·m , 9.0 kgf·m)
oil drain boltoil filterfront wheel axleboltfront wheel caliperfixing boltsfront wheel axlepinch boltsrear wheel axle nut
Torque Specifications
217
Specifications
Technical Information
05/06/09 16:12:43 31MBZ610_226
218
Break-in Guidelines
Technical Information
Help assure your motorcycle’s futurereliability and performance by payingextra attention to how you ride during thefirst 300 miles (500 km).
During this period, avoid full-throttlestarts and rapid acceleration.
05/06/09 16:12:47 31MBZ610_227
219
High Altitude Carburetor Adjustment
Technical Information
Your engine’s air-fuel mixture becomesoverly rich when operated at high altitudes.Above 6,500 feet (2,000 m), a richmixture can cause driveability problems,reduce engine performance, and increasefuel consumption. To compensate, youcan have the carburetors adjusted for highaltitude riding. See your Honda dealer.
However, the carburetors must be returnedto standard factory specifications beforeriding again at lower altitudes (below5,000 feet, 1,500 m). See your Hondadealer.
Sustained riding at lower altitudes with thelean high-altitude setting may cause roughidling, stalling, or engine damage fromoverheating.
05/06/09 16:12:52 31MBZ610_228
(2)
(1)
(1) vehicle emission control informationlabel
(2) vehicle emission control informationlabel (Canada only)
220
Emission Control Systems
Technical Information
Exhaust Emission RequirementsThe U.S. Environmental ProtectionAgency (EPA), the California AirResources Board (CARB), andEnvironment Canada require that yourmotorcycle comply with applicableexhaust emissions standards during itsuseful life, when operated and maintainedaccording to the instructions provided.
The Vehicle Emission ControlInformation label ( ) ( ) is attached tothe right swing arm.
1 2
05/06/09 16:12:57 31MBZ610_229
221
Emission Control Systems
Technical Information
Noise Emission Requirements
Warranty Compliance
Source of Exhaust EmissionsThe EPA also requires that motorcyclesbuilt after January 1, 1983 comply withapplicable noise emission standards forone year or 3,730 miles (6,000 km) afterthe time of sale to the ultimate purchaser,when operated and maintained accordingto the instructions provided. (USA only)
Compliance with the terms of theDistributor’s Warranties for HondaMotorcycle Emission Control Systems isnecessary in order to keep the emissionssystem warranty in effect. (USA only)
The combustion process produces carbonmonoxide (CO), oxides of nitrogen (NOx)and hydrocarbons (HC). Control ofhydrocarbons and oxides of nitrogen isvery important because, under certainconditions, they react to formphotochemical smog when subjected tosunlight. Carbon monoxide does not reactin the same way, but it is toxic.
Honda Motor Co., Ltd. utilizes varioussystems to reduce carbon monoxide,oxides of nitrogen and hydrocarbons.
05/06/09 16:13:02 31MBZ610_230
222 Technical Information
Emission Control Systems
Exhaust Emission Control System
Secondary Air Injection System
Evaporative Emission Control System(California only)The exhaust emission control system
includes a secondary air supply system,and an oxidation catalytic converter.
No adjustment to these systems should bemade although periodic inspection of thecomponents is recommended.
The secondary air injection systemintroduces filtered air into the exhaustgases in the exhaust port. The secondaryair injection system helps improveemission performance.
This motorcycle complies with therequirements of the California AirResources Board (CARB) evaporativeemission regulations. Fuel vapor from thefuel tank and carburetor is directed intothe charcoal canister and air cleaner whereit is absorbed and stored while the engineis stopped. When the engine is runningand the purge control diaphragm valve isopen, fuel vapor in the charcoal canisterand air cleaner is drawn into the enginethrough the carburetor.
05/06/09 16:13:06 31MBZ610_231
223Technical Information
Emission Control Systems
Problems That May Affect MotorcycleExhaust Emissions
Crankcase Emission Control System
Oxidation Catalytic Converter
If you are aware of any of the followingsymptoms, have the vehicle inspected andrepaired by your authorized Hondamotorcycle dealer.
Symptoms:Hard starting or stalling after startingRough idleMisfiring or backfiring duringaccelerationAfter-burning (backfiring)Poor performance (driveability) andpoor fuel economy
The oxidation catalytic converter is in theexhaust system. Through chemicalreactions, they convert HC and CO in theengine’s exhaust to carbon dioxide (CO )and water vapor.
The engine is equipped with a closedcrankcase system to prevent dischargingcrankcase emissions into the atmosphere.Blow-by gas is returned to the combustionchamber through the air cleaner and thecarburetor.
1.2.3.
4.5.
2
05/06/09 16:13:12 31MBZ610_232
224
Noise Emission Control System
Emission Control Systems
Technical Information
Removal of, or puncturing the muffler,baffles, header pipes or any othercomponent which conducts exhaustgases.Removal of, or puncturing of any partof the intake system.Lack of proper maintenance.Replacing any moving parts of thevehicle, or parts of the exhaust or intakesystem, with parts other than thosespecified by the manufacturer.
AMONG THOSE ACTS PRESUMEDTO CONSTITUTE TAMPERING ARETHE FOLLOWING ACTS:
TAMPERING WITH THE NOISECONTROL SYSTEM IS PROHIBITED:U. S. federal law prohibits, or Canadianprovincial laws may prohibit the followingacts or the causing thereof: ( ) Theremoval or rendering inoperative by anyperson, other than for purposes ofmaintenance, repair or replacement, of anydevice or element of design incorporatedinto any new vehicle for the purpose ofnoise control prior to its sale or delivery tothe ultimate purchaser or while it is in use;or ( ) the use of the vehicle after suchdevice or element of design has beenremoved or rendered inoperative by anyperson.
1.
2.
3.4.
1
2
05/06/09 16:13:17 31MBZ610_233
225Technical Information
Catalytic Converter
A defective catalytic converter contributesto air pollution, and can impair yourengine’s performance. Follow theseguidelines to protect your motorcycle’scatalytic converter.
Always use unleaded gasoline. Even asmall amount of leaded gasoline cancontaminate the catalyst metals, makingthe catalytic converter ineffective.
Keep the engine tuned-up.
Have your motorcycle diagnosed andrepaired if it is misfiring, backfiring,stalling or otherwise not runningproperly.
This motorcycle is equipped with anoxidation catalytic converter.The catalytic converter contains preciousmetals that serve as catalysts, promotingchemical reactions to convert the exhaustgasses without affecting the metals.
The catalytic converter acts on HC andCO. A replacement unit must be anoriginal Honda part or its equivalent.
The catalytic converter must operate at ahigh temperature for the chemicalreactions to take place. It can set fire toany combustible materials that come nearit. Park your motorcycle away from highgrasses, dry leaves, or other flammables.
05/06/09 16:13:20 31MBZ610_234
226
Oxygenated Fuels
Technical Information
Some conventional gasolines are beingblended with alcohol or an ethercompound. These gasolines arecollectively referred to as oxygenatedfuels. To meet clean air standards, someareas of the United States and Canada useoxygenated fuels to help reduce emissions.If you use an oxygenated fuel, be sure it isunleaded and meets the minimum octanerating requirement.Before using an oxygenated fuel, try toconfirm the fuel’s contents. Some states/provinces require this information to beposted on the pump.
The following are the EPA-approvedpercentages of oxygenates:
ETHANOL (ethyl or grain alcohol) 10%by Volume
You may use gasoline containing up to10% ethanol by volume. Gasolinecontaining ethanol may be marketedunder the name ‘‘Gasohol’’.
MTBE (Methyl Tertiary Butyl Ether) 15%by Volume
You may use gasoline containing up to15% MTBE by volume.
05/06/09 16:13:28 31MBZ610_235
227
Oxygenated Fuels
Technical Information
Oxygenated f uels can damage paint andplastic. Damage caused by spilled f uel isnot covered by warranty.
Fuel system damage or performanceproblems resulting from the use of anoxygenated fuel containing more than thepercentages of oxygenates mentionedabove are not covered under warranty.
Oxygenated fuels can damage paint andplastic. Be careful not to spill fuel whenfilling the fuel tank. Wipe up any spillsimmediately.
If you notice any undesirable operatingsymptoms, try another service station orswitch to another brand of gasoline.
METHANOL (methyl or wood alcohol)5% by Volume
You may use gasoline containingmethanol containing up to 5% methanolby volume as long as it also containscosolvents and corrosion inhibitors toprotect the fuel system. Gasolinecontaining more than 5% methanol byvolume may cause starting and/orperformance problems. It may alsodamage metal, rubber, and plastic partsof your fuel system.
05/06/09 16:13:33 31MBZ610_236
228 Technical Information
05/06/09 16:13:36 31MBZ610_237
229
Consumer Information
Consumer Information
This section contains information on yourwarranty and how to get an official Hondaservice manual.
............................Authorized Manuals . 230.............................Warranty Coverage . 233
.................................Warranty Service . 234................................Contacting Honda . 235
.............................Your Honda Dealer . 236The Honda Rider’s Club
..........................................(USA only) . 237Reporting Safety Defects
..........................................(USA only) . 238
05/06/09 16:13:39 31MBZ610_238
*
*
$60.00
$48.00
$16.00
61MBZ01
61CM002
31MBZ610
2006 CB600F Service Manual
Common Service Manual
2006 CB600F Owner’s Manual
Publication Item No. Description Price Each
Prices are subject to change without notice and without incurr ing obligation.
230
Authorized Manuals
Consumer Information
The Service Manual used by your authorized Honda dealer is available from Helm, Inc.(USA only, Canada: See your Honda dealer to order authorized manuals.)
Also available but not necessary to service your model is the Honda Common ServiceManual which explains theory of operation and basic service information for various systemscommon to all Honda motorcycles, motor scooters and ATVs.
These Honda manuals are written for the professional technician, but most mechanically-capable owners should find them easy to use if they have the proper tools and observe propersafety standards. Special Honda tools are necessary for some procedures.
05/06/09 16:13:46 31MBZ610_239
*
*
- -
Orders are mailed within 10 days. Please allow adequate time for
delivery.
Prices are subject to change without notice and without incurring
obligation.
Item DescriptionPublication
Item No.
Total
Price
Price
Each
Qty.
Handling Charge
Grand Total
$5.00
Sub Total
Purchaser’s Sales Tax
Mich. Add 6 %
Calif. Add 8.25 %
231
Order On-Line: www.helminc.com
Order Toll Free: 1-888-CYCLE93
OR
Consumer Information
(NOTE: For Credit Card Orders Only)
(1-888-292-5393)
Monday Friday 8:00 AM 6:00 PM EST
By completing this form you can order the materials desired. You can pay by check ormoney order, or charge to your credit card. Mail to Helm, Inc. at the address shown on theback of this order form (USA only).
Canada: See your Honda dealer to order authorized manuals.
05/06/09 16:13:55 31MBZ610_240
-
NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention theshipment should be sent.
Customer Name Attention
Zip CodeStateCity
Daytime Telephone Number
Check here if your billing address is different from theshipping address shown above.
Check or money order enclosed payable to Helm Inc.U.S. funds only. Do not send cash.
MasterCard
VISA
Discover
Account Number
Date
These Publications cannot be returned for credit without receiving advance authorization within 14 days of delivery. On returns, a restocking fee maybe applied against the original order.
Expiration: Mo. Yr.
Customer Signature
Apartment NumberStreet Address - No P. O. Box Number
( )
P.O. BOX 07280, DETROIT, MICHIGAN 48207HELM
SHIP
TO
PAYMENT
232 Consumer Information
05/06/09 16:14:11 31MBZ610_241
233
Warranty Coverage
Consumer Information
Your new Honda is covered by thesewarranties:
Motorcycle Limited WarrantyExhaust Emission WarrantyNoise Control Warranty
There are responsibilities, restrictions, andexclusions which apply to these warranties.Please read the Warranties Booklet givento you by your Honda dealer at the time ofpurchase. Be sure to keep your Hondaowner’s card with your WarrantiesBooklet (USA only).
It is important to realize that yourwarranty applies to defects in material orworkmanship of your Honda. Yourwarranty coverage does not apply tonormal wear or deterioration associatedwith using the motorcycle.
Your warranty coverage will not bevoided if you choose to perform your ownmaintenance. However, you should havethe proper tools and service informationand be mechanically qualified. Failuresthat occur due directly to impropermaintenance are not covered.
Almost all of your warranty coverage canbe extended through the Honda ProtectionPlan (USA only). For more information,see your Honda dealer.
05/06/09 16:14:16 31MBZ610_242
234
Warranty Service
Consumer Information
Please remember that recommendedmaintenance interval servicing is notincluded in your warranty coverage.Additionally, your warranty does notapply to the normal wear of items (such asbrakes, tires, etc.).
If you believe you have a problem withyour motorcycle, call the servicedepartment of your Honda dealer. Makean appointment for an inspection anddiagnosis. Remember, as the owner of themotorcycle, you will be asked to authorizethat inspection. Your dealer will give youthe results of the inspection. If theproblem is covered under warranty, yourdealer will perform the warranty repairsfor you.
If you have questions about warrantycoverage or the nature of the repair, it isbest to talk to the service manager of yourHonda dealer.
Sometimes, in spite of the best intentionsof all concerned, a misunderstanding mayoccur. If you aren’t satisfied with yourdealer’s handling of the situation, wesuggest you discuss your problem with theappropriate member of the dealership’smanagement team. If the problem hasalready been reviewed with the ServiceManager, Parts Manager, Sales Manager,etc., contact the Owner of the dealershipor their designated representative.
05/06/09 16:14:22 31MBZ610_243
235Consumer Information
Contacting Honda
Your owner’s manual was written to covermost of the questions you might ask aboutyour Honda. Any questions not answeredin the owner’s manual can be answered byyour Honda dealer. If your dealer doesn’thave the answer right away, they will getit for you.
Motorcycle Division, American HondaMotor Co., Inc., P.O. Box 2220, Torrance,CA 90509-2220, mailstop: 100-4W-5B,telephone: (866) 784-1870.
Canada: Refer to the Warranties Bookletthat was supplied with your vehicle.
Please include the following informationin your letter:
name, address, and telephone numberproduct model, year, and frame/VINserial numberdate of purchasedealer name and address
We will likely ask your Honda dealer torespond, or possibly acknowledge yourcomments directly.
If you have a difference of opinion withyour dealer, please remember that eachdealership is independently owned andoperated. That’s why it’s important towork to resolve any differences at thedealership level.
If you wish to comment on yourexperiences with your Honda or with yourdealer, please send your comments to thefollowing address (USA only):
05/06/09 16:14:28 31MBZ610_244
236 Consumer Information
Your Honda Dealer
Once you purchase your new Honda, getfamiliar with the organization of yourHonda dealer so you can utilize the fullrange of services available.
The service department is there to performregular maintenance and unexpectedrepairs. It has the latest available serviceinformation from Honda. The servicedepartment will also handle warrantyinspections and repairs.
The parts department offers GenuineHonda parts, Pro Honda products,Hondaline accessories (USA only), andHonda accessories and products (Canadaonly). The same quality that went intoyour Honda can be found in GenuineHonda replacement parts. You’ll also findcomparable quality in the accessories and
products available from the partsdepartment.
The sales department offers the HondaProtection Plan to extend almost all ofyour warranty coverage (USA only).Your Honda dealer can inform you aboutcompetition and other riding events inyour area. You’ll also find that your dealeris a source of information about AmericanHonda’s Rider Education Centers and theHonda Rider’s Club of America (USAonly).
We’re sure you’ll be as pleased with theservice your Honda dealer continues toprovide after the sale as you are with thequality and dependability of your Honda.
05/06/09 16:14:33 31MBZ610_245
237
The Honda Rider’s Club (USA only)
Consumer Information
Honda Red RiderHonda Red Rider ATV
One of the best ways to get the mostenjoyment from owning and riding yourHonda is through the Honda Rider’s Clubof America. Your purchase of a newmotorcycle, scooter, ATV or PWC from aparticipating U.S. Honda dealer entitlesyou to a complimentary one-yearmembership in the Club. There arehundreds of HRCA Chapter sponsoringdealers across the USA with events andactivities almost every weekend.Membership benefits include:
24 hour, toll-free roadside assistance foryour new Honda (includes roadsideassistance for your transport vehicle aslong as your Honda is aboard or in tow).Vehicle transport to the nearest Hondadealer or service center, if necessary.An exclusive HRCA website completewith access to the official Honda
Common Service Manual, contests,insider information and more.Reimbursement (up to $75) forMotorcycle Safety Foundation training.Separate free training from theSpecialty Vehicle Institute of Americafor ATV owners.One full year of themagazine or (forATV purchasers).Discounts from HRCA partners forexperienced rider courses.
Contact your Honda dealer for moreinformation or call: 1 800-847-HRCA orlog on to www.hrca.honda.com.
Discounted vehicle insurance from theHRCA’s insurance partner.Racing contingency programs andassistance at selected dual-sport, off-road, and motocross events.
05/06/09 16:14:41 31MBZ610_246
238 Consumer Information
Reporting Safety Defects (USA only)
If you believe that your vehicle has adefect which could cause a crash or couldcause injury or death, you shouldimmediately inform the National HighwayTraffic Safety Administration (NHTSA)in addition to notifying American HondaMotor Co., Inc.
To contact NHTSA, you may either callthe Auto Safety Hotline toll-free at1-800-424-9393 (or 366-0123 inWashington, D.C. area) or write to:NHTSA, U.S. Department ofTransportation, Washington, D.C. 20590.
You can also obtain other informationabout motor vehicle safety from theHotline.
If NHTSA receives similar complaints, itmay open an investigation, and if it findsthat a safety defect exists in a group ofvehicles, it may order a recall and remedycampaign. However, NHTSA cannotbecome involved in individual problemsbetween you, your dealer, or AmericanHonda Motor Co., Inc.
05/06/09 16:14:46 31MBZ610_247
239Consumer Information
05/06/09 16:14:48 31MBZ610_248
240
Table of Contents
Table of Contents
..................MOTORCYCLE SAFETY . 1
.......INSTRUMENTS & CONTROLS . 9
The following presents the contents ofeach section of your owner’s manual.
.................Important Safety Information . 2..................Accessories & Modifications . 5
...........................................Safety Labels . 7
..........Operation Component Locations . 11..............Gauges, Indicators & Displays . 14
......................Multi-function Display . 22
..Malfunction Indicator Lamp (MIL) . 23Low Oil Pressure Indicator and
..Malfunction Indicator Lamp (MIL) . 24......................................Speedometer . 25
Changing the Speed and Mileage....................................................Unit . 25
Odometer/Tripmeter A & B/............Mileage Countdown Display . 26
...........................................Odometer . 27...............................Tripmeter A & B . 27
..........................Mileage Countdown . 28.....Digital Clock/Stopwatch Display . 31
.....................................Digital Clock . 32..........................................Stopwatch . 35.........................................Fuel Gauge . 37
..............Coolant Temperature Meter . 39...............................Controls & Features . 41
......................................Choke Lever . 41..................................Ignition Switch . 42
........................................Start Button . 43...........................Engine Stop Switch . 43
................Headlight Dimmer Switch . 44............................Turn Signal Switch . 44
.......................................Horn Button . 45.....................................Select Switch . 45......................................Reset Switch . 46
High Coolant Temperature Indicator and
05/06/09 16:14:53 31MBZ610_249
?
?
241
Table of Contents
Table of Contents
...............................BEFORE RIDING . 47
.....BASIC OPERATION & RIDING . 59
...........SERVICING YOUR HONDA . 77
Service Preparations
Bef ore You Service Your Honda
(cont’d)
.....................Are You Ready to Ride . 48.............................Protective Apparel . 48
...................................Rider Training . 50...Is Your Motorcycle Ready to Ride . 51
............................Pre-ride Inspection . 51......................Load Limit & Guidelines . 54
..............................................Loading . 54.......................................Load Limits . 55
...........................Loading Guidelines . 55................Luggage Tie-Down Hooks . 57
........................Safe Riding Precautions . 60............Starting & Stopping the Engine . 61
.........................................Preparation . 61.............................Starting Procedure . 62
..................................Flooded Engine . 64....................How to Stop the Engine . 65
........................................Shifting Gears . 66
..................................................Braking . 68...................................................Parking . 70
.........Riding with a Passenger or Cargo . 75
...........The Importance of Maintenance . 80...............................Maintenance Safety . 81
............Important Safety Precautions . 82............................Periodic Maintenance . 84..........................Maintenance Schedule . 86
..............................Maintenance Record . 91
.....Maintenance Component Locations . 93..................................................Tool Kit . 96
.......................Owner’s Manual Storage . 97.........................................Seat Removal . 98
..............................Side Cover Removal . 99
05/06/09 16:14:58 31MBZ610_250
242
Table of Contents
Table of Contents
SERVICING YOUR HONDA (cont’d)
.....................................................TIPS . 169
Service Procedures
Fluids & Filters
Electrical
Chassis
Engine
......................................................Fuel . 100..............................Engine Oil & Filter . 103
.................................................Coolant . 113..........................................Air Cleaner . 117
................................................Throttle . 119......................................Clutch System . 121
................................Engine Idle Speed . 125..........................................Spark Plugs . 127
...........................................Suspension . 131..................................................Brakes . 134
.....................................................Tires . 140............................................Side Stand . 147..........................................Drive Chain . 148
..................................................Battery . 155
.................................Appearance Care . 160
............................Storing Your Honda . 170...........Transporting Your Motorcycle . 174
......................You & the Environment . 175
05/06/09 16:15:08 31MBZ610_251
243
Table of Contents
Table of Contents
TAKING CARE OF THE.................................UNEXPECTED . 177
.....TECHNICAL INFORMATION . 207
......CONSUMER INFORMATION . 229
.................TABLE OF CONTENTS . 240
................................................INDEX . 244
QUICK REFERENCE
..............................General Guidelines . 178..If Your Engine Quits or Won’t Start . 179
.......................If You Have a Flat Tire . 184...................If Your Engine Overheats . 196
If the Low Oil Pressure Indicator...................................................Lights . 198
....................................If a Fuse Blows . 199........................................If You Crash . 203
........................If You Lose Your Key . 204.......If Your Battery Is Low (or Dead) . 205
..........................Vehicle Identification . 208......................................Specifications . 211
.............................Break-in Guidelines . 218High Altitude Carburetor Adjustment . 219
..................Emission Control Systems . 220.............................Catalytic Converter . 225
................................Oxygenated Fuels . 226
............................Authorized Manuals . 230.............................Warranty Coverage . 233
.................................Warranty Service . 234................................Contacting Honda . 235
.............................Your Honda Dealer . 236The Honda Rider’s Club
..........................................(USA only) . 237Reporting Safety Defects
..........................................(USA only) . 238
05/06/09 16:15:11 31MBZ610_252
244
Index
Index
A C
B
...............................................accessories . 5............................................air cleaner . 117
..................................air pressure, tires . 140...............American Honda, contacting . 235
.................................apparel, protective . 48...................................appearance care . 160
..................................................battery . 155brakes,
..................................................fluid . 135.....................front lever adjustment . 134
...........................................pad wear . 138...................................................braking . 68
..............................break-in guidelines . 218
.......................................capacity, fuel . 101..................................care, appearance . 160
..........................................chain, drive . 148...........................................cleaner, air . 117
...................cleaning, appearance care . 160.cleaning, matte color painted surface . 164
.......................................clutch system . 121............................................color label . 210
compartment,.................................owner’s manual . 97
................................................tool kit . 96.........................consumer information . 229
..................................................coolant . 113.....................coolant temperature meter . 39
..................................customer service . 235
05/06/09 16:15:16 31MBZ610_253
245
Index
Index
D
E
F
......................................defects, safety . 238...........................................digital clock . 32
display,..................................................check . 16
....................................multi-function . 22...........................................drive chain . 148
.....................emission control systems . 220engine,
...............................................flooded . 64.........................................idle speed . 125
................................low oil pressure . 198.............................................number . 208
.....................................................oil . 103..........................................overheats . 196
.............................................pinging . 100
...............................................starting . 61.........................................stop switch . 43
..............................................stopping . 65........................................won’t start . 179.........................................environment . 175
..................................................flat tire . 184.......................................flooded engine . 64
......................................frame number . 209fuel,
..................................................gauge . 37.......................................oxygenated . 226
..............................recommendation . 100....................................tank capacity . 101
.....................................................fuses . 199
05/06/09 16:15:21 31MBZ610_254
246
Index
Index
G
H
I
K
.....................................gap, spark plug . 129.................................................gasohol . 226................................................gasoline . 100
................gauges, indicators & displays . 14
.......................headlight dimmer switch . 44.........................................helmet holder . 72
....high altitude carburetor adjustment . 219...............................high beam indicator . 17
Honda,........................................contacting . 235
.....................................Rider’s Club . 237................................................dealer . 236
.........................Honda service manual . 230.............................................horn button . 45
..........................identification, vehicle . 208................................idle speed, engine . 125
.......ignition cutoff system, side stand . 147.......................................ignition switch . 42
................................................indicators . 14................................inspection, pre-ride . 51
................................................key, lost . 204...................................................kit, tool . 96
05/06/09 16:15:27 31MBZ610_255
247
Index
Index
M
N
L
............................................labels, safety . 7.............................................lamp check . 15...........................................limit, weight . 55
..............................................load limits . 55..................................loading guidelines . 55
..........................................lock, steering . 71
maintenance,...........................component location . 93
.........................................importance . 80..............................................periodic . 84
.................................................record . 91..................................................safety . 81
.............................................schedule . 86..malfunction indicator lamp (MIL) . 14, 17
....................................manual, service . 230......matte color painted surface, clean . 164
..........................maximum weight limit . 55................................mileage countdown . 28
...........................................modifications . 6
.....................................numbers, serial . 208
05/06/09 16:15:32 31MBZ610_256
248
Index
Index
R
O
P
...................................................parking . 70....................................pinging, engine . 100
..........................................plugs, spark . 127.....................pre-load, rear suspension . 138
.................................pre-ride inspection . 51
..........................problems, unexpected . 177..................................protective apparel . 48
removal,.....................................................seat . 98
...........................................side cover . 99.......................reporting safety defects . 238
............................................reset switch . 46......................................rider training . 2, 50
............................Rider’s Club, Honda . 237riding,
...................................basic operation . 59..............................................clothing . 48
.........................................precautions . 60....................................................safety . 2
..............................safety precautions . 60.....................with passenger or cargo . 75
..........................................odometer . 14, 27oil,
...............................................engine . 103.....................................low pressure . 198
..................................operating controls . 41.............operation component locations . 11
...................................overheat, engine . 196.........................owner’s manual storage . 97
..................................oxygenated fuels . 226
05/06/09 16:15:37 31MBZ610_257
249
Index
Index
S
safety,........................important precautions . 80
....................................................labels . 7..............................reporting defects . 238..............................riding precautions . 60
...........................schedule, maintenance . 86...........................................seat removal . 98...........................................select switch . 45
......................................serial numbers . 208service,
...........................................customer . 235............................................manuals . 230...........................................warranty . 234
.........................................shifting gears . 66.............................................side stand . 147
..........side stand ignition cutoff system . 61..........................................spark knock . 100
...........................................spark plugs . 127.......................................specifications . 211
...........................................speedometer . 25............................................stand, side . 147.............................................start button . 43
starting,.................................................engine . 61
................................troubleshooting . 179...........................................steering lock . 71
................................stop switch, engine . 43......................................stopping engine . 65
...............................................stopwatch . 35
05/06/09 16:15:40 31MBZ610_258
250
Index
Index
Tstorage,
.......................................motorcycle . 170.................................owner’s manual . 97
suspension,.............rear suspension adjustment . 132
.......rear suspension spring pre-load . 133switch,
.........................................engine stop . 43...............................headlight dimmer . 44
...............................................ignition . 42....................................................reset . 46..................................................select . 45
..........................................turn signal . 44
........................................tachometer . 14,18....................temperature meter, coolant . 39
...............................theft prevention tips . 73..................................................throttle . 119
tires,.......................................air pressure . 140
....................................................flat . 184..........................................replacing . 144
....................................................tool kit . 96.....................................training, rider . 2, 50
..............transporting your motorcycle . 174............................................tripmeter . 19,27
.............................trouble, unexpected . 177......................troubleshooting, starting . 179
.............................turn signal indicators . 14
05/06/09 16:15:45 31MBZ610_259
251
Index
Index
W
V
..........vehicle identification no. (VIN) . 208
warranty,...........................................coverage . 233...........................................extended . 233
..............................................service . 234....................washing your motorcycle . 160
............................................weight limit . 55wheels,
...................................front removal . 187.....................................rear removal . 192
05/06/09 16:15:49 31MBZ610_260
252 Memo
05/06/09 16:15:51 31MBZ610_261
Quick Reference
Quick Reference
How To Avoid Costly RepairsThe following is a brief, but importantcollection of information you need toknow about your Honda. You’ll also findspace to record important notes. The engine of your Honda can be the most
expensive component to repair. Propermaintenance, especially the use of therecommended fluids and filters, preventspremature wear and damage.
Frequent causes of costly repairs are:Engine oil: insufficient quantity,improper oil.Air cleaner: dirty, leaking because ofimproper installation (poor seal).
Record important information on thefollowing page:
05/06/09 16:15:57 31MBZ610_262
Quick Reference
Quick Reference
VIN/Frame No.Engine No.Frame No.Ignition Key No.Color LabelOwner’s Name
AddressCity/StatePhone
Dealer’s NameAddressCity/StatePhoneService Mgr.
05/06/09 16:16:01 31MBZ610_263
4.49 US gal (17.0 )
384 lbs (174 kg)392 lbs (178 kg) Canada
Quick Reference
Quick Reference
ScheduledMaintenancePre-rideInspectionPeriodicChecksFuel/Capacity
Initial: 600 miles (1,000 km)Regular: every 4,000 miles (6,400 km)Check the following items each time before you ride (page ): tires &wheels, chain, leaks, loose parts, throttle, brakes, indicators, lights.Check the following items monthly (page ): tires & wheels, fluids,lights, freeplay, drive chain, fuses, nuts & bolts.unleaded gasoline, pump octane number 86 or higher
Engine Oil API Service Classification SG or higher except oils labeled as energyconserving on the circular API service label,SAE 10W-40, JASO T 903 standard MA,Pro Honda GN4 or HP4 (without molybdenum additives) 4-stroke oilor equivalent
Coolant ethylene glycol antifreeze (silicate-free) for aluminum engines in 50/50solution with Pro Honda HP Coolant or an equivalent distilled water
MaximumWeightCapacity rider, passenger, all cargo and accessories
51
85
05/06/09 16:16:13 31MBZ610_264
120/70 ZR17M/C (58W)
180/55 ZR17M/C (73W)BRIDGESTONE BT-56F RADIAL NMICHELIN Pilot ROAD S
BRIDGESTONE BT-56R RADIAL GMICHELIN Pilot ROAD S
10A, 20A30ACR9EH-9 (NGK) U27FER9 (DENSO)
42 psi (290 kPa , 2.90 kgf/cm )36 psi (250 kPa , 2.50 kgf/cm )
or
or
or
radial, tubeless
Quick Reference
Quick Reference
Tires
FusesSpark Plugs
Tire Pressure(cold)
Front:
Rear:
Front:Rear:
main :other:
standard:
Type:
05/06/09 16:16:23 31MBZ610_265