Threaded Inserts (TH series)
Can change through hole to threaded hole !!
TH Series
Change to through hole
TH Series
Change to through hole
THB Series
Change to non threaded inserts
THC Series
Change to non threaded inserts
Structure
Cream Solder
TH Series
PCB
Copper Foil
SHINDENKIZAI [email protected]
TH Series Mounting Process
1.On PCB land, apply Cream solder. By Mounter, put the parts
2.Reflow 3.Remove adsorption caps
Threaded Inserts TH series
Through hole is changed to threaded hole(M1.0,M1.2,M1.4,M1.7,M2, M2.6, M3). Taping type has adsorption cap for vacuum pick. It needs to be removed after reflow. ■Material: Brass ■Finish: Sn plating over Ni ■Recommended PCB Thickness:1.6t for TH-1.6 Series, 0.8t for TH-0.8 Series■Recommended Metal Mask Thickness:150-200μ
TH-0.8-M1.0 10A
TH-0.8-M1.2 12A
TH-0.8-M1.4 12A
TH-1.6-M1.6 15A
TH-1.6-M1.7 15A
TH-1.6-M2 20A
TH-1.6-M2.6 20A
TH-1.6-M3 30A
■Current Capacity ■ Tightening Torque TH-0.8-M1.0 0.3kgf-cm(2.94N-cm)and below
TH-0.8-M1.2 0.6kgf-cm(5.88N-cm)and below
TH-0.8-M1.4 1.0kgf-cm(9.8N-cm)and below
TH-1.6-M1.6 1.5kgf-cm(14.7N-cm)and below
TH-1.6-M1.7 1.5kgf-cm(14.7N-cm)and below
TH-1.6-M2 1.5kgf-cm(14.7N-cm)and below
TH-1.6-M2.6 3kgf-cm(29.4N-cm)and below
TH-1.6-M3X-dire 5kgf-cm(49N-cm)and below
Y-dire 3kgf-cm(29.4N-cm)and below
P/N A B C D M Package
TH-0.8-M1.0
2.5 1.6 0.7 0.5M1.0P=0.25
1000/reel
TH-0.8-M1.2
2.5 1.8 0.7 0.5M1.2P=0.25
1000/reel
TH-0.8-M1.4
2.7 2.0 0.7 0.7 M1.4P=0.3 1000/reel
TH-1.6-M1.6
3.0 2.2 1.5 0.3M1.6P=0.35
900/reel
TH-1.6-M1.7
3.0 2.3 1.5 0.3M1.7P=0.35
900/reel
TH-1.6-M2 4.0 2.5 1.5 0.3 M2P=0.4 900/reel
TH-1.6-M2.6
4.5 3.1 1.5 0.3M2.6P=0.45
900/reel
TH-1.6-M3 5.0 3.5 1.5 0.3 M3P=0.5 900/reel
*we can provide the bulk type *Mounter should have automatic recognition system
SHINDENKIZAI [email protected]
Threaded Inserts TH-0.8 series
■Current Capacity ■ Tightening Torque
■Stand-off type threaded inserts. This is mounted on PCB by inserting into through-hole. ■Screws can be inserted from both component and solder side. ■Taping type has adsorption cap for vacuum pick. It needs to be removed after reflow. ■Mounter should have automatic recognition system. ■Bulk type (100pcs/pack) is available.■Recommended PCB Thickness: 0.8-1.5t
TH-0.8-□-M2 20A
TH-0.8-□-M2.6
20A
TH-0.8-□-M3 30A
TH-0.8-□-M2 1.5kgf-cm (14.7N-cm) and below
TH-0.8-□-M2.6 3kgf-cm (29.4N-cm) and below
TH-0.8-□-M3
X dire 5kgf-cm (49N-cm) and below
Y dire 3kgf-cm (29.4N-cm) and below
P/N A B H M Package
TH-0.8-1.0-M2 4.0 2.5 1.0 M2 450/reel
TH-0.8-1.5-M2 4.0 2.5 1.5 M2 450/reel
TH-0.8-2.0-M2 4.0 2.5 2.0 M2 450/reel
TH-0.8-2.5-M2 4.0 2.5 2.5 M2 350/reel
TH-0.8-3.0-M2 4.0 2.5 3.0 M2 350/reel
TH-0.8-3.5-M2 4.0 2.5 3.5 M2 350/reel
TH-0.8-4.0-M2 4.0 2.5 4.0 M2 250/reel
TH-0.8-4.5-M2 4.0 2.5 4.5 M2 250/reel
TH-0.8-5.0-M2 4.0 2.5 5.0 M2 250/reel
TH-0.8-1.0-M2.6 4.5 3.1 1.0 M2.6 450/reel
TH-0.8-1.5-M2.6 4.5 3.1 1.5 M2.6 450/reel
TH-0.8-2.0-M2.6 4.5 3.1 2.0 M2.6 450/reel
TH-0.8-2.5-M2.6 4.5 3.1 2.5 M2.6 350/reel
TH-0.8-3.0-M2.6 4.5 3.1 3.0 M2.6 350/reel
TH-0.8-3.5-M2.6 4.5 3.1 3.5 M2.6 350/reel
TH-0.8-4.0-M2.6 4.5 3.1 4.0 M2.6 250/reel
TH-0.8-4.5-M2.6 4.5 3.1 4.5 M2.6 250/reel
TH-0.8-5.0-M2.6 4.5 3.1 5.0 M2.6 250/reel
TH-0.8-5.5-M2.6 4.5 3.1 5.5 M2.6 350/reel
TH-0.8-6.0-M2.6 4.5 3.1 6.0 M2.6 350/reel
TH-0.8-6.5-M2.6 4.5 3.1 6.5 M2.6 300/reel
TH-0.8-7.0-M2.6 4.5 3.1 7.0 M2.6 300/reel
TH-0.8-7.5-M2.6 4.5 3.1 7.5 M2.6 300/reel
TH-0.8-8.0-M2.6 4.5 3.1 8.0 M2.6 300/reel
P/N A B H MPackag
e
TH-0.8-1.2-M3 5.0 3.5 1.2 M3450/reel
TH-0.8-1.5-M3 5.0 3.5 1.5 M3450/reel
TH-0.8-2.0-M3 5.0 3.5 2.0 M3450/reel
TH-0.8-2.5-M3 5.0 3.5 2.5 M3350/reel
TH-0.8-3.0-M3 5.0 3.5 3.0 M3350/reel
TH-0.8-3.5-M3 5.0 3.5 3.5 M3350/reel
TH-0.8-4.0-M3 5.0 3.5 4.0 M3250/reel
TH-0.8-4.5-M3 5.0 3.5 4.5 M3250/reel
TH-0.8-5.0-M3 5.0 3.5 5.0 M3250/reel
TH-0.8-5.5-M3 5.0 3.5 5.5 M3350/reel
TH-0.8-6.0-M3 5.0 3.5 6.0 M3350/reel
TH-0.8-6.5-M3 5.0 3.5 6.5 M3300/reel
TH-0.8-7.0-M3 5.0 3.5 7.0 M3300/reel
TH-0.8-7.5-M3 5.0 3.5 7.5 M3300/reel
TH-0.8-8.0-M3 5.0 3.5 8.0 M3300/reel
TH-0.8-8.5-M3 5.0 3.5 8.5 M3250/reel
TH-0.8-9.0-M3 5.0 3.5 9.0 M3250/reel
TH-0.8-9.5-M3 5.0 3.5 9.5 M3250/reel
TH-0.8-10-M3 5.0 3.5 10 M3250/reel
SHINDENKIZAI [email protected]
Threaded Inserts TH-1.6 series
■Current Capacity ■ Tightening Torque
■Stand-off type threaded inserts. This is mounted on PCB by inserting into through-hole. ■Screws can be inserted from both component and solder side. ■Taping type has adsorption cap for vacuum pick. It needs to be removed after reflow. ■Mounter should have automatic recognition system. ■Bulk type (100pcs/pack) is available.■Recommended PCB Thickness: 1.6t and above
TH-1.6-□-M2 20A
TH-1.6-□-M2.6
20A
TH-1.6-□-M3 30A
TH-1.6-□-M2 1.5kgf-cm (14.7N-cm) and below
TH-1.6-□-M2.6 3kgf-cm (29.4N-cm) and below
TH-1.6-□-M3
X dire 5kgf-cm (49N-cm) and below
Y dire 3kgf-cm (29.4N-cm) and below
P/N A B H M Package
TH-1.6-0.5-M2 4.0 2.5 0.5 M2 450/reel
TH-1.6-1.0-M2 4.0 2.5 1.0 M2 450/reel
TH-1.6-1.5-M2 4.0 2.5 1.5 M2 450/reel
TH-1.6-2.0-M2 4.0 2.5 2.0 M2 450/reel
TH-1.6-2.5-M2 4.0 2.5 2.5 M2 350/reel
TH-1.6-3.0-M2 4.0 2.5 3.0 M2 350/reel
TH-1.6-3.5-M2 4.0 2.5 3.5 M2 350/reel
TH-1.6-4.0-M2 4.0 2.5 4.0 M2 250/reel
TH-1.6-4.5-M2 4.0 2.5 4.5 M2 250/reel
TH-1.6-5.0-M2 4.0 2.5 5.0 M2 250/reel
TH-1.6-0.5-M2.6 4.5 3.1 0.5 M2.6 450/reel
TH-1.6-1.0-M2.6 4.5 3.1 1.0 M2.6 450/reel
TH-1.6-1.5-M2.6 4.5 3.1 1.5 M2.6 450/reel
TH-1.6-2.0-M2.6 4.5 3.1 2.0 M2.6 450/reel
TH-1.6-2.5-M2.6 4.5 3.1 2.5 M2.6 350/reel
TH-1.6-3.0-M2.6 4.5 3.1 3.0 M2.6 350/reel
TH-1.6-3.5-M2.6 4.5 3.1 3.5 M2.6 350/reel
TH-1.6-4.0-M2.6 4.5 3.1 4.0 M2.6 250/reel
TH-1.6-4.5-M2.6 4.5 3.1 4.5 M2.6 250/reel
TH-1.6-5.0-M2.6 4.5 3.1 5.0 M2.6 250/reel
TH-1.6-5.5-M2.6 4.5 3.1 5.5 M2.6 350/reel
TH-1.6-6.0-M2.6 4.5 3.1 6.0 M2.6 350/reel
TH-1.6-6.5-M2.6 4.5 3.1 6.5 M2.6 300/reel
TH-1.6-7.0-M2.6 4.5 3.1 7.0 M2.6 300/reel
TH-1.6-7.5-M2.6 4.5 3.1 7.5 M2.6 300/reel
TH-1.6-8.0-M2.6 4.5 3.1 8.0 M2.6 300/reel
P/N A B H MPackag
e
TH-1.6-0.5-M3 5.0 3.5 0.5 M3450/reel
TH-1.6-1.0-M3 5.0 3.5 1.0 M3450/reel
TH-1.6-1.5-M3 5.0 3.5 1.5 M3450/reel
TH-1.6-2.0-M3 5.0 3.5 2.0 M3450/reel
TH-1.6-2.5-M3 5.0 3.5 2.5 M3350/reel
TH-1.6-3.0-M3 5.0 3.5 3.0 M3350/reel
TH-1.6-3.5-M3 5.0 3.5 3.5 M3350/reel
TH-1.6-4.0-M3 5.0 3.5 4.0 M3250/reel
TH-1.6-4.5-M3 5.0 3.5 4.5 M3250/reel
TH-1.6-5.0-M3 5.0 3.5 5.0 M3250/reel
TH-1.6-5.5-M3 5.0 3.5 5.5 M3350/reel
TH-1.6-6.0-M3 5.0 3.5 6.0 M3350/reel
TH-1.6-6.5-M3 5.0 3.5 6.5 M3300/reel
TH-1.6-7.0-M3 5.0 3.5 7.0 M3300/reel
TH-1.6-7.5-M3 5.0 3.5 7.5 M3300/reel
TH-1.6-8.0-M3 5.0 3.5 8.0 M3300/reel
TH-1.6-8.5-M3 5.0 3.5 8.5 M3250/reel
TH-1.6-9.0-M3 5.0 3.5 9.0 M3250/reel
TH-1.6-9.5-M3 5.0 3.5 9.5 M3250/reel
TH-1.6-10-M3 5.0 3.5 10 M3250/reel
SHINDENKIZAI [email protected]
Threaded Inserts THB series
Non-threaded type inserts for PCB through-hole. PCB is mounted above the chassis by inserting screws from the component side of PCB to tapped holes on the chassis. Taping type has adsorption cap for vacuum pick. It needs to be removed after reflow. Bulk type (100pcs/pack) is available.Bulk type does not have adsorption cap. ■Material: Brass ■Finish: Sn plating over Ni ■Recommended PCB Thickness: 1.6t
SHINDENKIZAI [email protected]
P/N A B C L H Package
THB-1.5-2 4.5 3.0 2.1 1.5 0.0 400/reel
THB-2.1-2 4.5 3.0 2.1 2.1 0.5 400/reel
THB-2.6-2 4.5 3.0 2.1 2.6 1.0 400/reel
THB-3.1-2 4.5 3.0 2.1 3.1 1.5 400/reel
THB-3.6-2 4.5 3.0 2.1 3.6 2.0 400/reel
THB-4.1-2 4.5 3.0 2.1 4.1 2.5 400/reel
THB-4.6-2 4.5 3.0 2.1 4.6 3.0 200/reel
THB-5.1-2 4.5 3.0 2.1 5.1 3.5 200/reel
THB-5.6-2 4.5 3.0 2.1 5.6 4.0 200/reel
THB-6.1-2 4.5 3.0 2.1 6.1 4.5 200/reel
THB-6.6-2 4.5 3.0 2.1 6.6 5.0 200/reel
THB-1.5-2.6
5.0 3.6 2.7 1.5 0.0 400/reel
THB-2.1-2.6
5.0 3.6 2.7 2.1 0.5 400/reel
THB-2.6-2.6
5.0 3.6 2.7 2.6 1.0 400/reel
THB-3.1-2.6
5.0 3.6 2.7 3.1 1.5 400/reel
THB-3.6-2.6
5.0 3.6 2.7 3.6 2.0 400/reel
THB-4.1-2.6
5.0 3.6 2.7 4.1 2.5 400/reel
THB-4.6-2.6
5.0 3.6 2.7 4.6 3.0 200/reel
THB-5.1-2.6
5.0 3.6 2.7 5.1 3.5 200/reel
THB-5.6-2.6
5.0 3.6 2.7 5.6 4.0 200/reel
THB-6.1-2.6
5.0 3.6 2.7 6.1 4.5 200/reel
THB-6.6-2.6
5.0 3.6 2.7 6.6 5.0 200/reel
THB-1.5-3 5.5 4.0 3.1 1.5 0.0 400/reel
THB-2.1-3 5.5 4.0 3.1 2.1 0.5 400/reel
THB-2.6-3 5.5 4.0 3.1 2.6 1.0 400/reel
THB-3.1-3 5.5 4.0 3.1 3.1 1.5 400/reel
THB-3.6-3 5.5 4.0 3.1 3.6 2.0 400/reel
THB-4.1-3 5.5 4.0 3.1 4.1 2.5 400/reel
THB-4.6-3 5.5 4.0 3.1 4.6 3.0 200/reel
THB-5.1-3 5.5 4.0 3.1 5.1 3.5 200/reel
THB-5.6-3 5.5 4.0 3.1 5.6 4.0 200/reel
THB-6.1-3 5.5 4.0 3.1 6.1 4.5 200/reel
THB-6.6-3 5.5 4.0 3.1 6.6 5.0 200/reel
Threaded Inserts THC1.6 series
■Stand-off type non-threaded inserts. This is mounted on PCB by inserting into through-hole. ■Taping type has adsorption cap for vacuum pick. It needs to be removed after reflow. ■Mounter should have automatic recognition system. ■Bulk type (100pcs/pack) is available.■Bulk type does not have adsorption cap. ■Material: Brass ■Finish: Sn plating over Ni ■Recommended PCB Thickness: 1.6t and above
P/N A B C HPackage
THC-1.6-0.5-2 4.5 3.0 2.1 0.5 450
THC-1.6-1.0-2 4.5 3.0 2.1 1.0 450
THC-1.6-1.5-2 4.5 3.0 2.1 1.5 300
THC-1.6-2.0-2 4.5 3.0 2.1 2.0 300
THC-1.6-2.5-2 4.5 3.0 2.1 2.5 250
THC-1.6-3.0-2 4.5 3.0 2.1 3.0 250
THC-1.6-3.5-2 4.5 3.0 2.1 3.5 200
THC-1.6-4.0-2 4.5 3.0 2.1 4.0 200
THC-1.6-4.5-2 4.5 3.0 2.1 4.5 400
THC-1.6-5.0-2 4.5 3.0 2.1 5.0 400
THC-1.6-5.5-2 4.5 3.0 2.1 5.5 350
THC-1.6-6.0-2 4.5 3.0 2.1 6.0 350
THC-1.6-6.5-2 4.5 3.0 2.1 6.5 300
THC-1.6-7.0-2 4.5 3.0 2.1 7.0 300
THC-1.6-7.5-2 4.5 3.0 2.1 7.5 300
THC-1.6-8.0-2 4.5 3.0 2.1 8.0 300
THC-1.6-0.5-2.6 5.0 3.6 2.7 0.5 450
THC-1.6-1.0-2.6 5.0 3.6 2.7 1.0 450
THC-1.6-1.5-2.6 5.0 3.6 2.7 1.5 300
THC-1.6-2.0-2.6 5.0 3.6 2.7 2.0 300
THC-1.6-2.5-2.6 5.0 3.6 2.7 2.5 250
THC-1.6-3.0-2.6 5.0 3.6 2.7 3.0 250
THC-1.6-3.5-2.6 5.0 3.6 2.7 3.5 200
THC-1.6-4.0-2.6 5.0 3.6 2.7 4.0 200
THC-1.6-4.5-2.6 5.0 3.6 2.7 4.5 400
THC-1.6-5.0-2.6 5.0 3.6 2.7 5.0 400
THC-1.6-5.5-2.6 5.0 3.6 2.7 5.5 350
THC-1.6-6.0-2.6 5.0 3.6 2.7 6.0 350
THC-1.6-6.5-2.6 5.0 3.6 2.7 6.5 300
THC-1.6-7.0-2.6 5.0 3.6 2.7 7.0 300
THC-1.6-7.5-2.6 5.0 3.6 2.7 7.5 300
THC-1.6-8.0-2.6 5.0 3.6 2.7 8.0 300
THC-1.6-8.5-2.6 5.0 3.6 2.7 8.5 250
THC-1.6-9.0-2.6 5.0 3.6 2.7 9.0 250
THC-1.6-9.5-2.6 5.0 3.6 2.7 9.5 250
THC-1.6-10-2.6 5.0 3.6 2.7 10.0 250
P/N A B C HPackage
THC-1.6-0.5-3 5.5 4.0 3.1 0.5 450
THC-1.6-1.0-3 5.5 4.0 3.1 1.0 450
THC-1.6-1.5-3 5.5 4.0 3.1 1.5 300
THC-1.6-2.0-3 5.5 4.0 3.1 2.0 300
THC-1.6-2.5-3 5.5 4.0 3.1 2.5 250
THC-1.6-3.0-3 5.5 4.0 3.1 3.0 250
THC-1.6-3.5-3 5.5 4.0 3.1 3.5 200
THC-1.6-4.0-3 5.5 4.0 3.1 4.0 200
THC-1.6-4.5-3 5.5 4.0 3.1 4.5 400
THC-1.6-5.0-3 5.5 4.0 3.1 5.0 400
THC-1.6-5.5-3 5.5 4.0 3.1 5.5 350
THC-1.6-6.0-3 5.5 4.0 3.1 6.0 350
THC-1.6-6.5-3 5.5 4.0 3.1 6.5 300
THC-1.6-7.0-3 5.5 4.0 3.1 7.0 300
THC-1.6-7.5-3 5.5 4.0 3.1 7.5 300
THC-1.6-8.0-3 5.5 4.0 3.1 8.0 300
THC-1.6-8.5-3 5.5 4.0 3.1 8.5 250
THC-1.6-9.0-3 5.5 4.0 3.1 9.0 250
THC-1.6-9.5-3 5.5 4.0 3.1 9.5 250
THC-1.6-10-3 5.5 4.0 3.1 10.0 250
*You can order THC-0.8 Series
SHINDENKIZAI [email protected]
