LW 35014 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2005
LW 35014 3
LW 35014 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2005
LEADWARRIORHISTORICAL MINIATURE Ebay: LEADWARRIOR
WWW.LEADWARRIOR.COM
LW 35014
The Sd.Kfz.11 (though some sources name this vehicle Sd.Kfz. 30, Sd.Kfz.261, or Sd.Kfz.251/17 Neu) was one of many conversions, utilizing the Sd.Kfz.251 halftrack chassis and Flak.30/38 Anti-Aircraft Gun.One of them was "Luftwaffe-Fla ausführung" (air force anti-aircraft version) - Lw35015 kit.Sd.Kfz.261 became the next variant. It was a hybrid - the front section and chassis is Sd.Kfz.251, behind the drivers seat the amour is newly designed to protect the seated crew and the ammo. It resembles the earlier unarmored platforms at the rear on the soft skinned halftracks.Prototype Utilized Sd.Kfz.251 Ausf.C, production version - Ausf.D.
31 RESIN PARTS
Sd.Kfz. 261 2cm Flak 38 auf mittlere Schutzenpanzerwagen
( Alias Sd.Kfz.30, Sd.Kfz.11, Sd.Kfz.251/17 Neu )
for DRAGON Sd.Kfz.251/1 Ausf. D
and TAMIYA, ITALERI or TRISTAR FlaK 38
1:35 CONVERSION KIT
3
* PAINT: Panzer Yellow overall
+ PHOTOETCH
* Use parts 20 (magazine cases) as you want.
M 1
3
M 1
13
13
* Use Dragon’s parts W3, W4, W5to mount parts 13 in openedor closed position
M 6
18
14
15
19
M 2
M 2
9
10
* Flak.38 ( Tristar, Italeri or Tamiya kit )
4
1
M 4(5)
M 3 8
6MAKE
Auto-Union A.G. of Chemnitz is awarded contract number 4911-021300306/42 to produce 2400 superstructures at the Horch assembly plant in Zwichau. March 1944 sees the first 5 completed. At the end of February 1945 a total of 604 are produced. Production continued in March April and May, but production statistics didn't survive. The target was 50 a month. It is seen on west and east front.Already in 1941 the FlaK 38 (2 cm) proves not capable to penetrate the Russian armored planes, usually the Ilushin 2. Therefore it was produced almost throughout the war. Most likely, as other vehicles utilizing 2cm. AA guns, it was used most often against ground targets. .
LW 35014 1
LW 35014 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2005
STUDY THE INSTRUCTION CAREFULLY BEFORE ASSEMBLING.
TEST FIT PARTS TOGETHER BEFORE CEMENTING.
USE CYANOACRYLATE GLUE FOR METAL AND RESIN PARTS.
2MAKE
?
Cut / Remove part
Optional Repeat several times
Repeat on mirror side
LW 35014 2
LW 35014 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2005
1
2
3
4 5
6
7
8
9
10
11
12 13 13
11
14 15
16 1718
19
20
20
1
14,5 mm
10,5 mm9,5 mm
10,5 mm9,5 mm
14,5 mm
Dragon part B1
Dragon part B2
Dragon part A1Dragon part A6
Dragon part W3 2MAKE
21
2
4(5)6(7)
17
17
16
12
11
11
* Numbers of the parts to be used on the right side, if not the same, are in parentheses: ( )