P/N Qty Description
Phillip screwdriver Straight-Slot screwdriverRatchet w/extension 10 mm socketDiagonal wire cutters Common pliersFlashlight Nylon trim tool Torque Wrench 36in. lbs.
Kit Contents
Hardware Bag Contents
Conflicts
Legend * Mandatory
STOP: Damage to the vehicle may occur. Do notproceed until process has been complied with.OPERATOR SAFETY: Use caution to avoidrisk of injury.CRITICAL PROCESS: Proceed with caution toensure a quality installation. These points will beaudited on a completed vehicle installation.TOOLS & EQUIPTMENT: This calls out thespecific tools and equipment required for thisprocess.REVISION MARK: This mark highlights achange in installation with respect to previousissue.
Recommended Tools
SPECIAL NOTE: Installation Sequences
After TMS and Safety mandated preparatory steps have been taken,the installation sequence is the suggested method for completing theaccessory installation. In some instances the suggested sequence iswritten for one associate to install and in others the sequence is givenas part of a team accessory installation. Unless otherwise stated inthe document, the associates may perform the installation steps inany order to make the installation as efficient as possible whilemaintaining consistent quality.
Safety Tools
Special Tools
INSTALLATION TOOLS
Special Chemicals
Vehicle Service Parts (may be required for reassembly)
Item # Quantity Reqd Description1 1 Keyless Module2 1 Main Harness3 1 Hardware Bag4 1 Valet Switch5 2 24" Cable Ties6 2 3-Button Transmitters
Item # Quantity Reqd Description1 8 Red T-Taps2 2 Blue T-Taps3 6 8" Cable Ties4 1 2-1/4"x 2-1/4" Foam Pad5 1 Yellow T-Tap
NOTE: Not for installation on vehilce's equipped withfactory installed keyless entry.
00016-79200-01 1 Keyless Entry Control Module00016-34030-05 2 Keyless Entry Transmitter00016-32901-01 1 Main Wiring Harness00016-30960-56 1 On/Off Toggle Control Switch00016-32901-02 1 Miscellaneous Hardware Kit00016-35105-01 1 Headlight Extension Wire
Toyota Corolla 2009 - Keyless Entry System
Part Number: 00016-32901Accessory Code: KE1
Southeast Toyota Distributors, LLC Page 1 of 11
INSTALLATION PREPARATION
Before starting installation
1. Familiarize yourself with the installation instructions.2. Inspect kit components.
VEHICLE PREPARATION
1. Place protective coverings on vehicle.
2. Disconnect negative battery clamp
Negative Battery Cable
3. Remove the driver's side scuff plate.Inserting a plastic panel tool under thescuff plate and prying upward todisengage the snap clips.
4. Remove the driver side kick panel byinserting a plastic panel tool under the kickpanel and carefully pry to disengage thesnap clips.
TOYOTA COROLLA KEYLESS ENTRY SYSTEM
Southeast Toyota Distributors, LLC Page 2 of 11
Optional step: Insert a plastic tool under the front
of the stuff plate & driver side kick panel lift only that area.
,
5. Remove (2) Phillips screws,from thedriver's lower finish panel (right side). Pullthe lower finish panel outward from thevehicle dash to disengage the snap clips.
7. Carefully seperate the lower steeringcolumn cover halfs by disengaging the (4)tabs and remove cover.
6. Pull the lower finish panel (left side)outward from the vehicle dash todisengage the snap clips.
TOYOTA COROLLA KEYLESS ENTRY SYSTEM
Southeast Toyota Distributors, LLC Page 3 of 11
IMPORTANT ! After installation, inspect & insure that all Keyless SystemHarness are clear of all HOT, SHARP or MOVING objects
CONNECTING THE KEYLESS SYSTEMHARNESS:
1. Carefully follow the wiring diagram andfactory connector details on pages 5&6 forTMC vehicle's and pages 7&8 for NUMMIvehicle's.
T-TAP INSTALLATION:
A. When installing female T - Tap connectors, be sure the wire is located inside the wire channel of thefemale T - Tap connector before closing connector over the wire with pliers.
Step A Step B Step C
T - Tap Wire from main keylessharness
MOUNTING MAIN CONTROL MODULE:
A. Secure the main module to the vehicleharness connected to the JB in the driver'sside kick panel area. Secure in place withthe long cable ties provided.
NOTE: Guide long cable through themodule eyelets as shown.
Keyless Module
INSTALLING PROCEDURES
TOYOTA COROLLA KEYLESS ENTRY SYSTEM
Southeast Toyota Distributors, LLC Page 4 of 11
NOTE: DO NOT WRAP OR BUNDLE ANTENNA HARNESS.Module antenna wire must extend up as high as possibleand secured in place for the best signal reception.
WIRING DIAGRAM COROLLA (TMC)W
IRIN
G D
IAG
RA
M
PIN
K [
Doo
r Lo
ck S
witc
h]:
Use
a r
ed T
-Tap
and
conn
ect t
o th
e LT
. BLU
E w
ire in
con
nect
or IE
2,lo
catio
n 16
.
PIN
K/W
HIT
E [
Doo
r Unl
ock
Switc
h]: U
se a
red
T-Ta
p an
d co
nnec
t to
the
YELL
OW
wire
in c
onne
ctor
IE2,
loca
tion
15.
PIN
K/W
HIT
E [D
oor U
nloc
k D
etec
t Sw
itch]
: Use
are
d T-
Tap
and
conn
ect
to t
he Y
ELLO
W w
ire i
nco
nnec
tor
IE1,
loca
tion
9.
WH
ITE
[Driv
er D
oor U
nloc
k M
otor
- To
war
ds D
oor
Lock
] - (S
ee D
etai
l A B
elow
)
BLU
E/W
HIT
E [ D
river
Doo
r Unl
ock
Mot
or - T
owar
dsB
ody
ECU
] - (S
ee D
etai
l A B
elow
)
RED
[+12
VDC
Bat
tery
]: Us
e a
red
T-Ta
p an
d co
nnec
tto
the
YELL
OW
wire
in c
onne
ctor
E4,
loca
tion
2.
YELL
OW
[ +1
2VD
C A
cces
sory
]: U
se a
red
T-Ta
pan
d co
nnec
t to
the
BLA
CK
wire
in c
onne
ctor
E4,
loca
tion
3.
CH
ASS
IS G
RO
UN
D -
Con
nect
the
ring
term
inal
to th
e 10
mm
bolt
at th
e dr
iver
's s
ide
kick
pan
el. (
fact
ory
grou
nd)
GR
EEN
/RED
WIR
E [H
orn]
: Use
red
T-Ta
p an
d co
nnec
t to
the
LT. G
REE
N W
IRE
in c
onne
ctor
E6,
loca
tion
8.
WH
ITE
WIR
E [T
ail L
ight
s]: U
se re
d T-
Tap
and
conn
ect t
o th
eW
HIT
E W
IRE
in c
onne
ctor
E8,
loca
tion
18.
2 Pi
n M
olex
Con
nect
or -
Plug
into
Tog
gle
Con
trol
Switc
h.
DET
AIL
"A
"
DR
IVER
'S D
OO
R U
NLO
CK
CIR
CU
IT
Cut
the
GR
EEN
WIR
E in
con
nect
or IE
2, lo
catio
n17
. St
rip t
he in
sula
tion
from
bot
h si
des
of t
hecu
t w
ire,
and
crim
p th
e W
HIT
E W
IRE
from
the
keyl
ess
harn
ess
to th
e H
AR
NES
S si
de o
f the
cut
wir
e. C
rim
p th
e B
LUE
/WH
ITE
WIR
E f
rom
the
keyl
ess
harn
ess
to th
e C
ON
NEC
TOR
sid
e of
the
cut
wire
.
Harn
ess
Wire
s
BLU
E w
/W
HIT
E
Cut
& S
trip
Exis
ting
Wire
WH
ITEB
LUE
WIR
E [H
eadl
ight
s - A
utom
atic
Tra
nsm
issi
on V
ehic
le]:
Use
red
T-Ta
p an
d co
nnec
t to
the
BLA
CK
WIR
E in
con
nect
orA
E11,
loca
tion
6. R
efer
to
page
6 f
or a
dditi
onal
det
ails
.
BLU
E W
IRE
[Hea
dlig
hts
- M
anua
l Tr
ansm
issi
on V
ehic
le]:
Con
nect
BLU
E ex
tens
ion
harn
ess
to t
he a
larm
BLU
E w
ire.
Use
red
T-Ta
p an
d co
nnec
t to
the
BLA
CK
WIR
E in
con
nect
orE9
1, lo
catio
n 6.
Ref
er t
o pa
ge 6
for
add
ition
al d
etai
ls.
Southeast Toyota Distributors, LLC Page 5 of 11
5. CONNECTOR E91 : Headlights (MT)Location : Behind glove box
Manual Transmission Vehicle's
Pin 6Black
Headlights
ALARM CAR BLUE** Black(Extension Wire)
Nummi Made Vehicle
1 23 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19 20
** Locate the BLUE extension wire harness inthe security kit. Attach the extension wire tothe alarm BLUE wire and route to the glovebox, passenger side area. Attach the vehicleBLACK wire, pin 6, as pictured above.
2. CONNECTOR E6 : HornLocation : Lower Steering Column Cover Area
Pin 8Lt. Green
Horn
CONNECTOR DETAILS: COROLLA (TMC)
3. CONNECTOR E8 : TailightsLocation : Lower Steering Column Cover Area
Pin 18White
Tail Lights
KEYLESS CARWhite White
1 2 3 4
5 6 7 8
1. CONNECTOR E4 : Ignition SwitchLocation : Steering Column
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
KEYLESS CARGreen/Red Lt. Green
KEYLESS CARRed YellowYellow Black
Pin 2Yellow
+12V Battery
Pin 3Black
+12V Accessory
121097
641 3 5
11
2
8
4. CONNECTOR AE11 : Headlights (AT)Location : High up in cowl, left of instrument panelAutomatic Transmission Vehicle's
Pin 6Black
Headlights
KEYLESS CARBlue Black
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
For manual transmission vehicle's, refer toStep 5, this page.
Black Connector
White Connector
White Connector
White Connector
Southeast Toyota Distributors, LLC Page 6 of 11
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
6. CONNECTOR IE2 : Door LocksLocation : Driver's Kick Panel Area
CONNECTOR DETAILS: COROLLA (TMC)
Door Lock SwitchBlue WireLocation 16
Door Unlock SwitchYellow WireLocation 15
Driver's Door Lock MotorLt. Green WireLocation 17**
Door Unlock Detect SwitchYellow WireLocation 9
KEYLESS CARPink BluePink/White YellowWhite Lt.Green (Lock Side)Blue/White Green (ECU Side)
** This vehicle wire must be cut in half, refer to page 5 for instructions.
7. CONNECTOR IE1 : Unlock DetectLocation : Driver's Kick Panel Area
KEYLESS CARPink/White Yellow
1 23 4 5 6 78 9 10 11 12
12
34567
89101112
White Connector Blue Connector
Southeast Toyota Distributors, LLC Page 7 of 11
WIRING DIAGRAM COROLLA (NUMMI)W
IRIN
G D
IAG
RA
M
PIN
K [
Doo
r Lo
ck S
witc
h]:
Use
a r
ed T
-Tap
and
conn
ect
to t
he V
IOLE
T w
ire in
co
nnec
tor
IE2,
loca
tion
16.
PIN
K/W
HIT
E [
Doo
r Unl
ock
Switc
h]: U
se a
red
T-Ta
p an
d co
nnec
t to
the
BEI
GE
wire
in c
onne
ctor
IE2,
loca
tion
15.
PIN
K/W
HIT
E [D
oor U
nloc
k D
etec
t Sw
itch]
: Use
are
d T-
Tap
and
conn
ect
to t
he Y
ELLO
W w
ire i
nco
nnec
tor
IE1,
loca
tion
9.
WH
ITE
[Driv
er D
oor U
nloc
k M
otor
- To
war
ds D
oor
Lock
] - (S
ee D
etai
l A B
elow
)
BLU
E/W
HIT
E [ D
river
Doo
r Unl
ock
Mot
or - T
owar
dsB
ody
ECU
] - (S
ee D
etai
l A B
elow
)
RED
[+12
VDC
Bat
tery
]: Us
e a
red
T-Ta
p an
d co
nnec
tto
the
RED
wire
in c
onne
ctor
E4,
loca
tion
2.
YELL
OW
[ +1
2VD
C A
cces
sory
]: U
se a
red
T-Ta
pan
d co
nnec
t to
the
GR
AY w
ire in
con
nect
or E
4,lo
catio
n 3.
CH
ASS
IS G
RO
UN
D -
Con
nect
the
ring
term
inal
to th
e 10
mm
bolt
at th
e dr
iver
's s
ide
kick
pan
el. (
fact
ory
grou
nd)
GR
EEN
/RED
WIR
E [H
orn]
: Use
red
T-Ta
p an
d co
nnec
t to
the
LT. G
REE
N W
IRE
in c
onne
ctor
E6,
loca
tion
8.
WH
ITE
WIR
E [T
ail L
ight
s]: U
se re
d T-
Tap
and
conn
ect t
o th
eB
RO
WN
WIR
E in
con
nect
or E
8, lo
catio
n 18
.
2 Pi
n M
olex
Con
nect
or -
Plug
into
Tog
gle
Con
trol
Switc
h.
Harn
ess
Wire
s
BLU
E w
/W
HIT
E
Cut
& S
trip
Exis
ting
Wire
WH
ITE
DET
AIL
"A
"
DR
IVER
'S D
OO
R U
NLO
CK
CIR
CU
IT
Cut
the
GR
EEN
WIR
E in
con
nect
or IE
2, lo
catio
n17
. St
rip t
he in
sula
tion
from
bot
h si
des
of t
hecu
t w
ire,
and
crim
p th
e W
HIT
E W
IRE
from
the
keyl
ess
harn
ess
to th
e H
AR
NES
S si
de o
f the
cut
wir
e. C
rim
p th
e B
LUE
/WH
ITE
WIR
E f
rom
the
keyl
ess
harn
ess
to th
e C
ON
NEC
TOR
sid
e of
the
cut
wire
.
BLU
E W
IRE
[Hea
dlig
hts
- Aut
omat
ic T
rans
mis
sion
Veh
icle
]:U
se re
d T-
Tap
and
conn
ect t
o th
e VI
OLE
T W
IRE
in c
onne
ctor
AE1
1, lo
catio
n 6.
Ref
er t
o pa
ge 9
for
add
ition
al d
etai
ls.
BLU
E W
IRE
[Hea
dlig
hts
- M
anua
l Tr
ansm
issi
on V
ehic
le]:
Con
nect
BLU
E ex
tens
ion
harn
ess
to t
he a
larm
BLU
E w
ire.
Use
red
T-T a
p an
d co
nnec
t to
the
VIO
LET
WIR
E in
con
nect
orE9
1, lo
catio
n 6.
Ref
er t
o pa
ge 9
for
add
ition
al d
etai
ls.
Southeast Toyota Distributors, LLC Page 8 of 11
5. CONNECTOR E91 : Headlights (MT)Location : Behind glove box
Manual Transmission Vehicle's
Pin 6Violet
Headlights
ALARM CAR Blue** Violet(Extension Wire)
Nummi Made Vehicle
1 23 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19 20
** Locate the BLUE extension wire harness inthe security kit. Attach the extension wire tothe alarm BLUE wire and route to the glovebox, passenger side area. Attach the vehicleVIOLET wire, pin 6, as pictured above.
2. CONNECTOR E6 : HornLocation : Lower Steering Column Cover Area
Pin 8Lt. Green
Horn
KEYLESS CARGreen/Red Lt. Green
121097
641 3 5
11
2
8
CONNECTOR DETAILS: COROLLA (NUMMI)
3. CONNECTOR E8 : TailightsLocation : Lower Steering Column Cover Area
Pin 18Brown
Tail Lights
1 2 3 4
5 6 7 8
1. CONNECTOR E4 : Ignition SwitchLocation : Steering Column
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
Pin 2Red
+12V Battery
Pin 3Gray
+12V Acessory
4. CONNECTOR AE11 : Headlights (AT)Location : High up in cowl, left of instrument panelAutomatic Transmission Vehicle's
Pin 6Violet
Headlights
KEYLESS CARBlue Violet
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
KEYLESS CARRed RedYellow Gray
KEYLESS CARWhite Brown
For manual transmission vehicle's, refer toStep 5, this page.
White Connector
Black Connector
White Connector
White Connector
Southeast Toyota Distributors, LLC Page 9 of 11
CONNECTOR DETAILS: COROLLA (NUMMI)
Door Unlock Detect SwitchYellow WireLocation 9
7. CONNECTOR IE1 : Unlock DetectLocation : Driver's Kick Panel Area
KEYLESS CARPink/White Yellow
1 23 4 5 6 78 9 10 11 12
12
34567
89101112Wh
White Connector
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
6. CONNECTOR IE2 : Door LocksLocation : Driver's Kick Panel Area
Door Lock SwitchViolet WireLocation 16
Door Unlock SwitchBeige WireLocation 15
Driver's Door Lock MotorGreen WireLocation 17**
KEYLESS CARPink VioletPink/White BeigeWhite Green (Lock Side)Blue/White Green (ECU Side)
** This vehicle wire must be cut in half, refer to page 7 for instructions.
White Connector
Southeast Toyota Distributors, LLC Page 10 of 11
COMPLETING THE INSTALLATION: COROLLA
TESTING THE SYSTEM:
1. Prior to delivering the vehicle, test allfeatures of the system accordinng to theowner's manual included.
LOCK - Press and release the LOCK buttonon the transmitter. All doors should lock,headlights should come on.
UNLOCK - Press and release the UN-LOCK button on the transmitter. The driver'sdoor should unlock, headlights should comeon.
Press and release the UNLOCK buttonagain. All doors should unlock.
Press and hold the PANIC button. The hornshould sound and the parkings lights shouldflash.
Press and release the PANIC button tosilence the horn.
NOTE: Be sure to test both transmitter thatwere included in the kit.
ASSEMBLE ALL REMOVED PANELS TOTHE VEHICLE:
1. Refer again to the vehicle repair manualand reassemble all panels that were removedfor installation back onto the vehicle. Testthoroughly, all mechanical componentsdisconnected and or removed from thevehicle during the installation of thisaccessory.
PREPARING THE VEHICLE FOR DELIVERY:1. To set the arm/disarm chirps to "soft"chirps.
2. Start with the doors in the unlockedposition, Toggle Control Switch in the "OFF"position.
3. Turn the ignition key to the on position.
4. Turn the ignition key off, then immediatelyswitch the Toggle Control Switch "ON" then"OFF" 4 times.
5. The vehicle horn should respond with softhorn chirps.
Southeast Toyota Distributors, LLC Page 11 of 11
Note: Re-torque battery cable to 36in lb. once process is completed.
Negative Battery Cable