The information presented in this publication has beencarefully checked for reliability; however, noresponsibility is assumed for inaccuracies.Specifications are subject to change without notice.
Trademarks
IBM, PC/AT, and PC/XT are trademarks ofInternational Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
AMD is a trademark of Advanced Micro Devices Inc.
Cyrix is a trademark of Cyrix Corporation.
IDT is a trademark of Integrated Devices TechnologyCorporation.
Award is a registered trademark of Award SoftwareInc.
MS-DOS and WINDOWS NT are registered trademarksof Microsoft Corporation.
iiContentsChapter 1: Introduction ...................................................................... 2
Key Features ................................................................................... 3Unpacking the Mainboard & Static Electricity Precautions..... 5
Chapter 2: Hardware Configuration ................................................ 6Mainboard Component Locations ............................................... 7Connectors....................................................................................... 8
PWR2 Ð AT Power Supply Connectors ............................... 8COM1/2 Ð Serial Port #1/#2................................................. 8PRN1 Ð Parallel Port ............................................................... 8FDC1 Ð Floppy Disk Port ....................................................... 8IDE1/IDE2 Ð Primary/Secondary IDE Ports...................... 8KBD Ð Keyboard Connector .................................................. 8PS1 Ð PS/2 Mouse Connector ............................................... 8PS2 Ð PS/2 Mouse Pin Header .............................................. 8J1 Ð ATX Form Card Connector: ........................................... 8J11 (1, 3, 5, 7, 9) (KEYLOCK) Ð Keylock & Power LEDConnector ................................................................................. 8J11 (2, 4, 6, 8) (SPK) Ð Speaker Connector............................ 9J11 (13, 14) (TB-LED) Ð Turbo LED Connector ................... 9J11 (15, 16) (HDD-LED) Ð HDD LED Connector ................ 9J11 (17, 18) (RST) Ð Reset Switch Connector ....................... 9J11 (19, 20) (SP-LED) Ð Suspend LED Connector ............. 10FAN-PWR Ð Fan Power Connector .................................... 10Sound Pro Connectors: ......................................................... 10J5/J6 Ð Analog Audio for Sony/Panasonic ....................... 10J2 Ð Sound and Game ........................................................... 10J3/J4 Ð Digital Audio OUT/IN ........................................... 10
Jumper Settings ............................................................................ 11JP3 Ð CMOS RAM Clear Selector........................................ 11JP10 Ð CPU Type Selectors ................................................... 11JP8 Ð DIMM Voltage Selectors ............................................ 12JP1 Ð Microphone Type Selector ......................................... 12JP6 Ð CPU Core Voltage Selectors....................................... 12JP5 Ð CPU Multiplier Selectors............................................ 13JP9 Ð CPU Frequency Selectors ........................................... 13
Memory Installation..................................................................... 14
iiiChapter 3: ACPI Functions & Connectors with ATX Power..... 15
PWR1 Ð ATX Power Connector .......................................... 15Software Power-Off .............................................................. 16Modem Ring Power-On ....................................................... 16Alarm Wake Up .................................................................... 16J11 (21, 22) (SUSÐSW) Ð ATX Power Button and SuspendSwitch Connector .................................................................. 17
Chapter 4: BIOS Setup ..................................................................... 18Entering BIOS Setup .................................................................... 19Defaults.......................................................................................... 20
Load Setup Defaults ............................................................. 20Load Best Performance Defaults......................................... 20
Setup Items.................................................................................... 20Standard CMOS Setup ......................................................... 20BIOS Features Setup ............................................................. 22Chipset Features Setup......................................................... 24Power Management Setup................................................... 25* * PM Events * * .................................................................. 26PCI/Plug and Play Setup..................................................... 27Peripheral Setup.................................................................... 28Password Setting ................................................................... 30IDE HDD Auto Detection .................................................... 30Save & Exit Setup .................................................................. 30Exit Without Saving.............................................................. 30
Chapter 1Introduction
This mainboard is a high-performance mainboardbased on the advanced Pentiumª microprocessor andfeaturing, 100MHz CPU external clock speedcapability, PCI Local Bus and the high-end AGPchipset. The mainboard offers a high degree offlexibility in configuration and is fully IBM PC/ATcompatible.
Introduction 3
Key Features
The advanced features of this mainboard include:¥ Supports P54C/P55C Pentiumª (MMX) CPUs and
Cyrix/IBM 6x86L/6x86MX/MII, AMD K6/K6-2(3.2V & 2.2V), IDT C6 90~350MHz CPUs withFrequency at 60/66/75/83/95/100 MHz andselectable 66/100MHz clock for SDRAM while theexternal frequency of CPU is running at 100MHz;
¥ Provides three DIMMs for SDRAM/EDO/FPM memory modules, memory expandable up to 384MB;
¥ Supports 64M-bit (8Mx8, 4Mx16) EDO DRAM/SDRAM;
¥ Supports 1MB Pipeline Burst synchronous L2cache;
¥ Provides both ATX/AT power connector, andsupports various ATX power functions, such as:Modem Ring On, ATX Power Button, SuspendSwitch, and Alarm Wake Up;
¥ Supports ACPI and Legacy PMU, and the UltraDMA/33, fully compliant to PC97 & PC98;
¥ Supports Accelerated Graphics Port (AGP) v1.0,3 PCI Bus slots, 2 ISA Bus slots;
¥ PCI Bus Master IDE interface with 2 connectorswhich supports 4 IDE devices in 2 channels;
¥ Super Multi-I/O chip supports 2 serial ports with16550 compatible fast UART, 1 parallel port withEPP and ECP capabilities, and one floppy diskdrive interface with 1Mb/s transfer rate;
¥ Provides PS/2 Mouse connector/pin header, andATX Form Card containing PS/2 Mouse, 2 USBinterface, and Infrared connectors (optional);
4 Chapter 1
¥ 3D Sound Pro meets PC98' SPEC and support HRTF Positional Audio, Direct Sound 3D provide drivers for3D games that use Aureal software interface, Software Wave-table Synthesizer, and Digital Audio Interface (SPDIF) IN/OUT;
¥ System BIOS Supports TrendÕs ChipAway Virusfunction to ensure the entire boot process isvirusfree, no installation and configuration worries;
¥ Bundled PC-cillin97 (OEM) provides automaticvirus protection for Window95 and the Internet.
Introduction 5
Unpacking the Mainboard & StaticElectricity Precautions
This Mainboard package contains the following items:
1. This Mainboard
2. The Device Driver for this mainboard
3. This UserÕs Guide
4. Sound & Game ribbon cables/bracket
5. ATX Form Card (optional)
The mainboard is easily damaged by static electricity.Follow the precautions below while unpacking orinstalling the mainboard.
1. Do not remove the mainboard from its originalpackage until you are ready to install it.
2. Frequently ground yourself to discharge any staticelectric charge that may build up in your bodywhile working on installation and/orconfiguration. For example, you may groundyourself by grasping an unpainted portion of thesystemÕs metal chassis.
3. Remove the mainboard from its anti-staticpackaging and place it on a grounded surface,component side up.
4. Handle the mainboard by its edges or by themounting bracket to avoid touching itscomponents.
5. Check the mainboard for damage. If any integratedcircuit appears loose, press carefully to seat itfirmly in its socket.
6. Do not apply power if the mainboard appearsdamaged. If there is damage to the board contactyour dealer immediately.
Chapter 2Hardware Configuration
Before you install this mainboard into the systemchassis, you may find it convenient to first configurethe mainboardÕs hardware. This chapter describes howto set jumpers and install memory modules, and whereto attach components.
Hardware Configuration 7
Mainboard Component Locations
PCI3 PCI2 PCI1
DIMM3DIMM2DIMM1
COM2 COM1
Socket 7
PWR2
KBDPS1
1 2 1 2
FDC1
1
J1
2 1
18 17
Battery
+
IDE21
IDE11
3
1
HDD-LED
SPK RST
SP-LED
J11 2
TB-LED SUS-SW
KeylockCache
Cache
BIO
S
Chipset
1J6
J5
JP8
PRN11
1
2221
I/O
So
un
dP
ro
J2
1 2
JP1
JP2
J3
PS2
1 2
PWR1
5V
3.3V
J4
AGP1
Chipset
1
JP3
P55C
P54C
JP10
3
1JP5
B AC
JP6
BC
DA
31JP9
BC
AD
1
FAN-PWR
Figure 2Ð1. Mainboard Component Locations
8 Chapter 2
Connectors
Attach system components and case devices to themainboard via the mainboard connectors. A descriptionof each connector follows. See Figure 2Ð1 for thelocation of the connectors on the mainboard.
Note: Make sure that the power is turned off beforemaking any connection to the board.
PWR2 – AT Power Supply ConnectorsCOM1/2 – Serial Port #1/#2PRN1 – Parallel PortFDC1 – Floppy Disk PortIDE1/IDE2 – Primary/Secondary IDE PortsKBD – Keyboard ConnectorPS1 – PS/2 Mouse ConnectorPS2 – PS/2 Mouse Pin Header
J1 – ATX Form Card Connector:
This connector contains 2 sets of USB interface, PS/2Mouse, and Infrared connectors. Connect the ATXForm Card cable to this connector.
J11 (1, 3, 5, 7, 9) (KEYLOCK) – Keylock &Power LED Connector
Pin Description
1 LED Output3 N.C.5 Ground7 Keylock9 Ground
Hardware Configuration 9
J11 (2, 4, 6, 8) (SPK) – Speaker Connector
Pin Description
2 Data Out4 N.C.6 Ground8 +5V
J11 (13, 14) (TB-LED) – Turbo LEDConnector
Pin Description
13 (+) +5V14 (Ð) Active Low
J11 (15, 16) (HDD-LED) – HDD LEDConnector
Pin Description
+ +5VÐ Active Low
J11 (17, 18) (RST) – Reset SwitchConnector
Pin Description
Open Normal ModeClose Reset System
10 Chapter 2
J11 (19, 20) (SP-LED) – Suspend LEDConnector
Pin Description
19 (+) +5V20 (Ð) Active Low
FAN-PWR – Fan Power Connector
Pin Description
1 Sense2 +12V3 Ground
Sound Pro Connectors:
J5/J6 – Analog Audio for Sony/Panasonic
Connect to ÒAUDIOÓ on the CD-ROM drive.
J2 – Sound and Game
Sound contains Line-in/MIC (Microphone), and Line-out (Speaker). Game connector is also the Joysticconnector. Connect this connector to the Sound &Game ribbon cable/bracket as the following drawing:
Line-In MIC Line-Out Game
J2 J2
J3/J4 – Digital Audio OUT/IN
Connect this connector to the Digital Audiodevice/DIGITAL AUDIO on the CD-ROM drive(depending on the type of your CD-ROM drive).
Hardware Configuration 11
Jumper Settings
JP3 – CMOS RAM Clear Selector
Description Setting
Normal Mode3
1
Clear CMOS3
1
Note: 1. Make sure that this jumper is set to Normal Modebefore installing the mainboard and the power isoff before clearing the CMOS.
2. If using the ATX power, you need to unplug thepower cable and then plug the cable back on afterclearing the CMOS.
JP10 – CPU Type Selectors
CPU Setting ExampleP55C
(Dual Voltage)P54C
P55C Intel MMX, AMDK6/K6-2, IBM/Cyrix6x86L/6x86MX (MII)
P54C(Single Voltage)
P54C
P55C Intel P54C, IDT C6,AMD K5, IBM/Cyrix
6x86
12 Chapter 2
JP8 – DIMM VoltageSelectors
Voltage Setting
5V3
1
3.3V3
1
JP1 – Microphone TypeSelector
Description Setting
Special Mode
Normal Mode(Default)
JP6 – CPU Core Voltage Selectors
Vcc Setting
A B C D
2.1V
A B C D
2.2V
Vcc Setting
A B C D
2.5V
A B C D
2.7V
A B C D
2.8V
Vcc Setting
A B C D
2.9V
A B C D
3.2V
A B C D
3.3V
A B C D
3.5V
Hardware Configuration 13
JP5 – CPU Multiplier Selectors
A
A
A
A
A
A
A
A
1.5X/3.5X
Mul. Setting
2.0X
B
12
3
2.5X
Mul.
3.0X
4.0X
Mul.
B
12
3
4.5X
B
12
3
5.0X
B
12
3
5.5X
B
12
3
B
12
3
B
12
3
B
C
C
C
C
C
C
C
C
12
3
Setting Setting
JP9 – CPU Frequency Selectors
60MHz
Fre.
66MHz
75MHz(PCI 37.5M)
Fre.
75MHz(PCI 30M)
100MHz(SDRAM 66M)
83MHz
Fre.Setting
A B C D
32
1
A B C D
32
1
Setting
A B C D
32
1
A B C D
32
1
Setting
A B C D
32
1A B C D
32
1
100MHz(SDRAM 100M)
A B C D
32
195MHz
(SDRAM 66M)
A B C D
32
1
95MHz(SDRAM 95M)
A B C D
32
1
14 Chapter 2
Memory Installation
The mainboard lets you add up to 384MB of systemmemory. Three DIMM sockets are divided into three banks: Bank 0, Bank 1, and Bank 2. The mainboard supports the following memoryconfigurations.
Bank Memory ModuleBank 0DIMM1 4MB, 8MB, 16MB, 32MB, 64MB, 128MB
Bank 1DIMM2 4MB, 8MB, 16MB, 32MB, 64MB, 128MB
Bank 2
DIMM3 4MB, 8MB, 16MB, 32MB, 64MB, 128MBTotal System Memory = Bank 0 + Bank 1 + Bank 2
Notes: The speed of all DIMMs modules have to be faster than 70ns.
Chapter 3ACPI Functions & Connectors
with ATX Power
PWR1 – ATX Power Connector
The ATX power supply provides a single 20-pinconnector and supports the ACPI specification.
Pin Description Pin Description
1 3.3V 11 3.3V2 3.3V 12 Ð12V3 Ground 13 Ground4 +5V 14 PS-ON5 Ground 15 Ground6 +5V 16 Ground7 Ground 17 Ground8 Power OK 18 Ð5V9 5VSB 19 +5V10 +12V 20 +5V
16 Chapter 3
The functions and connectors described below workwith the ATX power supply.
Software Power-Off
Follow the steps below to use the ÒSoftware Power-OffControlÓ function in Windows 95 with ATX powersupply.
1. Click the START button on the Windows 95 taskbar.
2. Select Shut Down The Computer to turn off thecomputer. The message ÒIt is now safe to turn offyour computer.Ó will not be shown when using thisfunction.
Modem Ring Power-On
While in Soft-off/Suspend state, if an external modemring-up signal occurs, the system wakes up and can beremotely accessed. Make sure that the Ring ResumeFrom Soft Off option is set to Enabled in the BIOS setupsection (Refer to the Power Management section inChapter 4.)
Alarm Wake Up
If you want to autoboot the system at a certain time, setthe function of RTC Alarm time properly and thefunction of RTC Alarm Resume From Soft Off option inthe BIOS Setup section will be set to Enabled.
ATX Functions & Connectors 17
J11 (21, 22) (SUS–SW) – ATX Power Button and SuspendSwitch Connector
Attach the ATX Power Button or Suspend Switch cableto this connector.
In the AT power system, this connector will act as asuspend switch; and in the ATX power system, thisconnector will be not only an ATX power button but aSuspend switch as well. Details are described below:
When the system is off, push the power button to turnthe system on. When the system is on, push the powerbutton rapidly to switch the system to the Suspendmode, and, by pushing and holding the button formore than 4 seconds, it will turn the system completelyoff. When the system is in the Suspend mode, push thepower button rapidly to turn the system on.
Chapter 4BIOS Setup
This chapter explains how to configure the mainboardÕsBIOS setup program. The setup program providedwith the mainboard is the BIOS from Award.
After you have configured the mainboard and haveassembled the components, turn on the computer andrun the software setup to ensure that the systeminformation is correct.
The software setup of the system board is achievedthrough Basic Input-Output System (BIOS)programming. You use the BIOS setup program to tellthe operating system what type of devices areconnected to your system board.
The system setup is also called CMOS setup. Normally,you need to run system setup if either the hardware isnot identical with information contained in the CMOSRAM, or if the CMOS RAM has lost power.
Note: Hold down the <End> key or to clear CMOS for amoment then set back to Normal Mode then power onto reboot the system when installing newer BIOS intothis mainboard .
BIOS Setup 19
Entering BIOS Setup
To enter the BIOS Setup program:
1. Turn on or reboot the system. A screen appearswith a series of diagnostic checks.
2. When ÒHit <DEL> if you want to run SETUPÓappears, press the <DEL> key to enter the BIOSsetup program. The following screen appears:
ROM PCI/ISA BIOS (2A5LEHOA)CMOS SETUP UTILITYAWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION SETUP
LOAD BEST PERFORMANCE DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
PASSWORD SETTING
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
Esc: Quit ↑ ↓ → ←: Select ItemF10 : Save&Exit (Shift) F2: Change Color
3. Use your keyboard to choose options.Modify system parameters to reflect systemoptions. Press Alt-H for Help.
20 Chapter 4
Defaults
Every option in the BIOS Setup contains two defaultvalues: Best default and the Setup default value.
Load Setup Defaults
The Setup default values provide optimum systemsettings for all devices and system features.
Load Best Performance Defaults
The Best default values provide best performancesettings for all devices and system features, howeverdepending on the devices used, these settings are notrecommend for long hours of work load.
Setup Items
Standard CMOS Setup
Choosing the item from the BIOS Setup main menu.All Standard setup options are described in this section.
Date/Time Select the Date/Time option to change the dateor time. The current date and time aredisplayed. Enter new values through thedisplayed window.
BIOS Setup 21
Pri Master;Pri Slave;Sec Master;Sec Slave
Choose these options to configure the harddisk drive named in the option. When youenter an option, the following parameters arelisted: Type, LBA/Large Mode, Block Mode,32Bit Mode, and PIO Mode. All parametersrelate to IDE drives except Type. Choose theType parameter and select Auto BIOSautomatically detects the IDE drive parametersand displays them. Choose on LBA Mode andchoose On to enable support for IDE driveswith capacities greater than 528MB. Click onBlk Mode and choose On to support IDEdrives that use Blk Mode. Click on 32BitMode and click on On to support IDE drivesthat permit 32-bit accesses.
Floppy DriveA; B
Choose the Floppy Drive A or B option tospecify the floppy drive type. The settings are360KB 51/4", 1.2MB 51/4", 720KB 31/2", 1.44MB31/2", or 2.88MB 31/2".
Video This option is to select the video display mode.
Halt On This option is to halt system on a specifiederror.
22 Chapter 4
BIOS Features Setup
Choosing the item from the BIOS Setup main menu.All advanced setup options are described in thissection.
Trend ChipAwayVirus
Set this option to enable the TrendChipAway Virus function.
CPU Internal Cache This option selects to enable the internalcache or not. Choices are Disabled andEnabled.
External Cache This option enables/disables the externalcache memory.
Quick Power OnSelf Test
Set this option to Enabled to permit BIOS toboot within 5 seconds.
Boot Swquence Set these options to select the bootsequence from different booting devices.
Swap Floppy Drive This option allows you to swap floppydrives between A: and B:.
Boot Up FloppySeek
Choose Enabled or Disabled. Disabledprovides a faster boot and reduces thepossibility of damaging the heads.
Boot Up Numlockstatus
When set to On, allows the BIOS toautomatically enable the Num LockFunction when the system boots up.
Boot Up SystemSpeed
Allows to select the speed of booting upthe system.
BIOS Setup 23
Gate A20 Option When Fast is selected, this option allowsthe A20G bus line signal generated fromthe chipset to directly pass to port 92H,instead of the keyboard controller. it willspeed up the system performance.
Memory Parity/ECCCheck
This option is to enable ECC checking ofmemory parity.
Typematic RateSetting
The term typematic means that when akeyboard key is held down, the characteris repeatedly entered until the key isreleased. When this option is enabled, youmay change the typematic repeat rate.
Typematic Rate(Chars/Sec)
Sets the repeat rate of a character while thekey is held.
Typematic Delay(Msec)
Sets the delay time before a character isrepeated.
Security Option This option specifies the type of BIOSpassword protection that is implemented.The settings are:Setup: The password prompt appears
only when an end user attemptsto run WinBIOS Setup.
Always: A password prompt appearsevery time the computer ispowered on or rebooted.
The BIOS password does not have to beenabled. The end user sets the passwordby choosing the Password icon on theWinBIOS Setup screen.
IDE SecondChannel Control
Allows you to enable or disable the IDEsecondary channel.
24 Chapter 4
PCI VGA PaletteSnoop
When this option is set to Enabled,multiple VGA devices operating ondifferent buses can handle data from theCPU on each set of palette registers onevery video device.
OS Select ForDRAM Over 64MB
You need to set this option to OS2 whenusing the OS/2 operating system withinstalled DRAM which is greater than64MB.
Video BIOSShadow;C8000, 16K Shadow;CC000, 16K Shadow;D0000, 16K Shadow;D4000, 16K Shadow;D8000, 16K Shadow;DC000, 16K Shadow
Disabled: The specified ROM is notcopied to RAM.
Enabled: The contents of the ROM areaare not only copied from ROMto RAM for faster execution, thecontents of the RAM area canbe written to or read from cachememory.
Cached: The contents of the ROM areaare copied from ROM to RAMfor faster execution.
Chipset Features Setup
Choose the item from the BIOS Setup main menu. AllChipset Setup options are then displayed and aredescribed in the following section:
Bank 0/1, 2/3, 4/5DRAM Timing
Set these options to select the speed of usedmemory bank.
Cache Timing Set this option to select the speed of cachetiming.
Video BIOSCacheable
Set this option to enable video BIOS readingfrom cache memory.
BIOS Setup 25
System BIOSCacheable
Set this option to enable BIOS copying thesystem BIOS from ROM to RAM for fasterexecution.
AGP Aperture Size Choose 4MB, 8MB, 16MB, 32MB, 64MB,128MB, or 256MB. Memory-mapped,graphics data structures can reside in theGraphics Aperture. Use the default setting.
OnBoard USB Choose Enabled or Disabled. Set thisoption to enable the system BIOS USB(Universal serial Bus) functions.
Power Management Setup
Choosing the item from BIOS Setup main menu.
PowerManagement
Set this option to select power managementfeatures.
PM Control byAPM
Choose Yes for the Advanced PowerManagement to control power management.
Video Off Option This option specifies the power conservingstate that the VESA VGA video subsystementers after the specified period of displayinactivity has expired.
Video Off Method Set this option to specify the method of videopower saving.
Modem Use IRQ Set this option to specify IRQ for modemdevice.
Soft-Off byPWRBT
Set this option to specify the method of PowerButtons switch to Soft-Off.
26 Chapter 4
HDD PowerDown
This option specifies the power conservingstate that the hard disk drive enters after thespecified period of hard drive inactivity hasexpired.
Doze Mode This option specified the length of systeminactivity while in Full power on state. Whenthis length of time expires, the computerenters Doze power state.
Suspend Mode This option specified the length of a period ofsystem inactivity while in Doze state. Whenthis length of time expires, the computerenters Suspend power state.
* * PM Events * *VGA;LPT & COM;HDD & FDD;DMA/Master;IRQ3, 4, 5, 6, 7, 8,9, 10, 11, 12, 13, 14,15
When these options are not set to OFF orDisabled, they enable event monitoring on thespecified hardware interrupt request line andthe computer is in a power saving state, BIOSwatches for activity on the specified IRQ line.The computer enters the full on power state ifany activity occurs.
Modem RingResume
Set this option to enable the modem ring toresume from Soft-Off.
RTC AlarmResume
Set this option to enable the RTC Alarm towake up the system which is Soft Off.
Date (of Month);Timer (hh:mm:ss)
Set these options to specify the RTC Alarmtime on Date/Hour/Minute/Second.
Primary INTR Set this option ON to enable event monitoringto IRQs.
BIOS Setup 27
PCI/Plug and Play Setup
Choose the item from the BIOS Setup main menu.
PNP OS Installed Set this option to Yes if the operation systemin this computer is aware of and follows thePlug and Play specification.
ResourcesControlled By
Set this option to specify resources controlledby Auto or Manual.
IRQÐ3, 4, 5, 7, 9,10, 11, 14, 15assigned to
These options specify the bus that thespecified IRQ line is used on. These optionsallow you to reserve IRQs for legacy ISAadapter cards.
DMAÐ 0, 1, 3, 5, 6,7 assigned to
These options specify the bus that thespecified DMA channel is used on.
PCI Master 0 WSWrite
Set this option to enable 0 WS write for PCImaster.
PCI Master ReadPrefetch
Set this option to enable reading prefetch forPCI master.
AGP Master 1 WSWrite/Read
Set these options to enable 1 WS write/readfor AGP master.
PCI IRQ ActivedBy
Set this option to specify active mode of PCIIRQ.
Assign IRQ ForUSB
Set this option to enable assigning IRQ toUSB.
Assign IRQ forVGA
This option is used to allocate IRQ to VGA.Recommendation is set to No.
28 Chapter 4
Peripheral Setup
Choose the item from the BIOS Setup main menu.
OnBoard IDEFirst/SecondChannel
Set these options to enable IDE first/secondchannel on the motherboard.
IDE PrefetchMode
Set this option to enable IDE in the prefetchmode.
IDE PrimaryMaster PIO;IDE Primary SlavePIO;IDE SecondaryMaster PIO;IDE SecondarySlave PIO;
Set these options to select PIO mode or todetect it by BIOS for IDE devices.
IDE PrimaryMaster UDMA;IDE Primary SlaveUDMA;IDE SecondaryMaster UDMA;IDE SecondarySlave UDMA;
Set these options to enable UDMA functionfor IDE devices.
Init AGP DisplayFirst
Set this option to enable fresh initialing theAGP display while the system is rebooting.
OnBoard FDCController
This option enables the FDC (Floppy DriveController) on the motherboard or autodetects the FDC.
OnBoard SerialPort1
This option specifies the base I/O portaddress of serial port 1.
BIOS Setup 29OnBoard SerialPort2
This option specifies the base I/O portaddress of serial port 2.
IR Address Select set this option to select IR address or todisable IR function.
IR Mode Set this option to specify IR mode for HPSIRor ASKIR.
IR IRQ Select Set this option to specify IRQ to IR function.
OnBoard ParallelPort
This option specifies the base I/O portaddress of the parallel port on themotherboard.
Parallel Port Mode Depends on the type of your external devicewhich connects to this port to choose Normal,EPP, or ECP mode.
ECP Mode UseDMA
Set this option to specify DMA for ECP whenECP was selected in above Parallel Port Modeoption.
OnBoard SoundChip
This option is designed to be used to enablethe Sound Pro functions.
30 Chapter 4
Password Setting
This item lets you configure the system passwordwhich is required every time when the system boots upor an attempt is made to enter the Setup program. Thepassword cannot be longer than six characters.
Note: Keep a safe record of the new password. If you forgetor lose the password, the only way to access the systemis to clear CMOS memory by holding down the<End> key then powering on to reboot the system.
IDE HDD Auto Detection
If your system has an IDE hard drive, you can use thisutility to detect its parameters and automatically enterthem into the Standard CMOS Setup. This utility willautodetect up to four IDE devices.
Save & Exit Setup
Select this item to save the values entered during thecurrent session and then exit the BIOS setup program.
Exit Without Saving
Select this item to exit the BIOS setup program withoutsaving the values which has been entered during thecurrent session.