Trima Leaflet

www.trima.se

Because it works!

2

Because it works!

3

Hard work always produces unique results. Farmers and loader manufacturers both know this. Behind the new Trima Plus loader range you will discover a great deal of hard development work derived from a close dialogue with farmers. Benefiting the user is our priority. We have therefore focused on the tractor’s properties and created new front loader technology with just one goal in our sights - the whole picture.

Almost everything in the Trima Plus is new, and everything is well thought-out. The front loader beam and pins have been increased in

size, giving you greater power during critical lifting operations. Trima Plus has large working angles, enabling the implements to be used to the full. Faster implement changes and faster connection and disconnection of the loader are factors that simplify the day-to-day work.

The new Trima Plus delivers quality on every front, from superb manouverability, to excel-lent visibility and the simplest tractor servic-ing possible. The trend is for agriculture to become more demanding and the tractors ever larger. As a farmer you are entitled to modern loader technology that is one step ahead

Trima optimises!+ New subframes+ Completely new beam design with curved cross tube+ No hydraulic pipes and hoses along the beam sides+ All pins are reinforced+ Stronger cylinder designs+ Perfect visibility from the driver’s seat+ Newly developed shock absorber - PlusDrive+ New central valve - Plus Compact Valve+ New, wide front loader+ New tool carrier that maximises visibility when changing implements

Does it have an equal?

Is there an equally durable system for large tractors, long front loaders, large lifting capacity and really wide implements? The subframes have all been designed with larger dimensions, and the front loader is now secured with a locking pin with a 30 % larger diameter. The distance between the load-bearing point and the pivot point for the loader beam is very short. In addition, the surfaces where the bearing box meets the subframe have been precision-machined and extended. These improvements guarantee a safe and functional subframe system between tractor and front loader. Quite simply, you gain access to a sound overall product that maximises the potential for working with precision, without wear and tear.

Simple tractor service

Trima’s subframes have a vertical design. Connection also takes place vertically. The reason is obvious.

Modern tractors with versatile service options should be supported by a functional subframe and locking system that do not take up unnecessary space.

Excellent driving properties

With modern tractors it is easy to manoeuvre in dif-ficult terrain. Solutions that do not restrict the front wheels’ movements are therefore best for the tractor. Vertical subframes and carefully designed front loader fixing points provide more space for large wheels and mudguards. This allows you to get the maximum turn-ing radius.

Newly developed cross tubes

The curved cross tube is a new design feature that provides more room for both front weights and front linkages. The cross tube is also located towards the front of the front loader. This means that large front loaders can be installed further back on the tractor, enabling the weight distribution and stability to be improved. It also means that the machine as a whole is shorter and the driving properties more convenient. The forward location of the cross tube also ensures that it does not obscure the tractor’s headlights.

For better control

From the driver’s seat it is easy to follow the imple-ment’s movements via the new position indicator. It is short and compact, and has three positions that can be adapted for different implements according to individual needs. The low position reduces the risk of damage to the indicator.

”The perfect front loader. That is Trima”

Free surfaces

The hydraulics are concealed inside the beam. The driver sees only clean surfaces, without pipes and hoses obscuring his vision. In addition, the front loader and its subframes are the optimum width. All in all, the new design offers many advantages: + Perfect visibility towards the implement+ More space for service work+ More space for front linkages+ Eliminated risk of damage to hydraulic pipes + No problems with muck or branches catching on pipes and hoses

4

Because it works!

55

1 By installing two powerful stays over the loader beams, mechanical parallel linkage and greater lifting force are achieved. This means that the front loader can reach a greater working speed thanks to smaller, faster lifting cylinders.

This is where the name Plus Link comes from - the front loader’s and the tractor’s poten-tial are increased. In addition, mechanical parallel linkage means that the load forces are distributed between more points, in turn reducing the total wear on the front loader.

2 Here is an explanation of another advantage of using a mechanical parallel linkage. Note that the lifting cylinder (represented by the counter-weight) is in the same position as in picture 1, despite the fact that the weight on the forks

has been moved further out. The lifting force required is the same, irrespective of where on the implement the load is situated. This means that the front loader does not lose lifting capacity when handling material where the centre of gravity is often far out at the front.

3 In order to handle the same load, a front loader without parallel linkage must be equipped with considerably larger lifting cylinders (represented by the counter-weight). The loads are concentrated on a smaller number of pins,

and without the mechanical stays the front loader does not have the same strength.

All farmers naturally look after their bodies, tractors and products. This is why Trima Plus is packed full of technology that delivers a combination of performance and safety. Parallel linkage ensures control over the work, and the optional PlusDrive equipment guarantees comfortable handling of both the material and the driver. Trima Plus has been developed with consideration that benefits both your wallet and your job satisfaction and health.

PlusDrive - extra safeEveryone who has invested in a new Trima Plus will really appreciate PlusDrive, a further improved shock absorber.

+ Protected location inside the powerful, curved cross tube. Nothing can damage PlusDrive

+ Concealed location provides improved visibility towards the implement from the driver’s seat

+ All hose connections are protected

+ During grading work, the implement follows the ground without unnecessary load on the implement - the results are perfect and there is reduced wear on the implement

+ PlusDrive delivers careful handling of all loads. No spillage from the bucket and no damage to plastic bales

Good damping increases the tractor’s potential, at the same time as reducing the loads on subframes, trac-tor subframe, axles, tyres and rims. Above all, how-ever, it protects the driver’s body during hard driving.

+ Equipped with rotary control for Off and On

+ Extra equipment: electrical connection and disconnection from the cab. The loader can rapidly be switched from full damping on the ground to no damping when precision is required for high-level stacking

Plus Link™. When logic wins throughTrima Plus is a range of front loaders driven by technology. Occasionally, however, the least complicated solution is and remains the best. For this reason, the most powerful loaders in the Trima Plus range are fitted with mechanical parallel linkage. This is a logical consequence of many years’ loader development. Mechanical parallel linkage gives:+ Approximately 25 % greater lifting force

+ Greater lifting force with smaller cylinders

+ Higher working speed/greater efficiency

+ Greater lifting force far out on the implement

+ More power for handling pallets and straw

+ Better distribution of the load forces

+ Stronger and more torsionally rigid design

+ Maximum utilisation of the tractor’s hydraulics

and comfortable!

”Thoughtful. That is Trima”

With just one hose and via the new Plus Compact Valve, PlusDrive is connected to both sides of the lifting cylinders. This achieves damping in both direc-tions. An extra safety measure - the front loader beam cannot drop and cause damage, as PlusDrive can only be switched on if the implement is on the ground.

Because it works!

6

Because it works!

7

Simpler implement changes with an efficient front loader that offers improved visibility. In the Trima Plus, professionals now have a work tool that combines strength with technology. A natural continuation of Trima’s tradition of always putting the user’s needs first. The new Plus Compact Valve, new implement tool carrier, wide front loader models, large working angles and centrally located quick-couplings for the 3rd service. All go together to provide a surplus of functionality.

Optimum angle, irrespective of the taskLarge implement angles make it possible to work with full load and with all possible materials. However, the design of the implement is also important, so that the correct filling and dumping angle can be achieved, whatever the task. When the implement is replaced, the optimum working angle is automatically achieved.

Ergonomic connectionInside the implement tool carrier, behind a protective plate, is the robust mechanical implement lock. There is no risk of either handles or locking pins being damaged in the event of a collision. If the loader is equipped with the 3rd service, the quick-couplings have a protected and easily accessible location be-hind the tool carrier. This means that connecting the implement is performed from a single position on the left side and at a comfortable height. Good for the body, efficient for the work.

A central new featureThe new Plus Compact Valve symbolises Trima Plus. This is a very logical solution, compared to the multitude of hydraulic solutions currently available. Instead of building up several valve plates and adding more hoses and couplings, with an increased risk of pressure loss and leakage, everything is gathered into a single unit - Plus Compact Valve - which has been designed to withstand the considerable hydraulic pressures and large volumes of oil found in modern tractors.

The tractor’s hydraulic oil flows directly to the Plus Compact Valve, which distributes the oil at an even pressure to the relevant lifting and implement cylinders. This means that the same pressure is delivered simultaneously to both sides of the loader helping it to move smoothly without any ”lopsided” effect.+ Double shock valves that protect the implement cylinders in both directions+ Plug In hoses for the 3rd service+ Pressure-relieving feature for the quick-couplings on the 3rd and 4th services - so that implements can be connected more easily+ Prepared for connection of 4th service+ Prepared for on/off function for hydraulic implement locking+ Integrated on/off function for PlusDrive+ Rotatable hose couplings - for eliminating twisting, e.g. when the implement cylinders are in operation+ Ozone-resistant hoses for maximum service life Reinforced cross tube

There is naturally a reinforcement plate in the transition between the curved cross tube and the stable beam profile. This reduces stress and torsional loading.

Overview provides controlModern tractors are characterised by having hydraulic pipes and hoses concealed beneath bonnets and body-work. Trima Plus focuses on these same properties. See the similarities! Where are the hydraulic components? The tractor is designed to give the best possible visibility. The front loader should therefore offer the same.

Accidents sometimes happen. In order to avoid dam-age to the loader beam and cylinders, shock valves are triggered, for example if the bucket collides with a solid obstacle. The oil is then re-routed to the other side of the cylinder and the bucket can move past the obstacle.

”Fantastic visibility. That is Trima”

Changing implements has never been easierIncredibly good visibility from the driver’s seat and solid implement locking are Trima’s signature. Trima Plus’ new implement tool carrier will not disappoint anyone - on the contrary, the tool carrier can now be turned all the way down so that the implement hook can be seen directly from the driver’s seat. Add to this a broad front loader beam, which offers good visibility between the front loader and the front of the tractor - and the end result is complete control when changing the implement. It has to be seen to be believed!

8

Because it works!

9

The new Trima Plus front loader range is also based on Trima’s motto: ”the tractor’s and the driver’s best friend”. When the tractor delivers more strength, Trima Plus does the same. If farmers want to work faster, our loaders make sure that they can. Trima Plus focuses on solutions that make operations easier and with less stress.

Correctly positioned valveOnce the front loader is connected, you want to get started, not have to wait and tamper with things. The tractor’s hydraulics are connected directly to Trima Plus’ hydraulic valve. The position of this valve means that it does not become soiled by dirt etc.

Also: The valve for ElectroDrive CDC (optional extra) is supplied with an accumulator in order to ensure trouble-free operation, constant pressure and simpler connection of the quick-couplings.

Bearing box with large contact surfacesAs Trima Plus has a powerfully dimensioned front loader, which will be subjected to extreme forces, we have developed an entirely new bear-ing box. This can absorb and stabilise these stresses. A careful choice of materials is combined with large contact surfaces, high precision, profile extrusions and a reinforced box construction. We have also succeeded in achieving a compact design that provides more room for front wheels and mudguards.

Ready for most thingsPlus Lock is a typical Trima creation. The short, robust locking pin has a diameter of 40 mm and meets all the needs of new tractors, large front loaders and heavy implements.

Quick connectionTrima Plus Lock stands for simple, secure locking. When the front loader is put onto the subframe, the bearing box guides itself into position. All that has to be done is to push in the locking pin, pull out the locking button and turn the handle in behind the locking button. To disconnect, the button is pulled out, the handle twisted off and the locking pin pulled out. The handle can then be hung on the locking button, so that it is always available.

More powerful pinsRemember that all loads to which a front loader is subjected must

be taken up by the pins. We have therefore developed new pins for the Trima Plus. Many of the pins are 25 % larger. The rotary locks have also been strengthened. In order to further reduce wear and

axial play, as well as to keep the lubrication in the right place and the dirt out, the pins are provided with a special tensioning device with a

compact disc and rubber ring. Effectively the pins are fixed and sealed at both ends.

In addition, all the pins are rustproof (electro-galvanised). Lubrication is normally performed easily from the outside of the front loader.

Strong support legsA ”simple thing” like support legs should

not prevent a smooth flow of work. We are always aiming to achieve safer solu-tions. The slender, profile-pressed, more powerful support legs are well integrated with the front loader and are always eas-ily accessible for when the front loader is to be parked. The locking system makes

it easy to find the correct height. A broad, articulated foot provides a

larger contact surface. No loose compo-nents to be lost!

Reinforced cylindersWith regard to materials, design and manufacture, you could not want

anything else - Trima Plus cylinders are modern all the way through. The steep cyl-inder transitions are reinforced so that the loads can be absorbed and distributed evenly. Trima Plus’ parallel linkage loaders have implement cylinders with through

piston rods which give a higher emptying speed. In addition, the piston rods are rein-forced at three points, making any type of quick-emptying valve unnecessary. Double

bearings contribute to the longer service life of the cylinders.

U-profile with many strengthsU-profiles are an established Trima speciality. Trima Plus stands for increased

torsional and flexural rigidity, as well as for excellent steel quality. The beam is light and the forces are distributed better through the entire construction. The 70 mm wide profile comprises two U-profiles lying one inside the other. The welded joints

face in towards the tractor, giving a smooth, continuous surface that does not col-lect dirt. All the corners and edges on the profile-pressed plate halfway along the

arm are also attractively rounded off.

Perfect controlCable-controlled ErgoDrive helps the driver to operate

the loader’s lifting and lowering movements, as well as the implement’s crowding and dumping movements.

These functions can be combined for many tasks, increasing efficiency. For the best ergonomic working position, ErgoDrive can be adjusted and positioned in

the cab according to your wishes. It is equipped with two push-button switches for 3rd and 4th services. Using a special safety function, the lever can be locked to pre-

vent unwanted front loader movements.

”Safe and quick. That is Trima”

10

Because it works!

11

Even though, in its basic version, Trima Plus provides users with professional opportunities to develop their operations, it is a definite plus if you can offer even more of an edge when required. Trima holds the position as “the driver’s best friend”.

Auto Plus - new implement lockingA tractor driver climbs up to and down from the cab several times a day. With the new Auto Plus (hydraulic implement locking), the number of times the driver has to climb in and out is dramatically reduced. Connection and disconnection take place simply from the driver’s seat. Indicators on the tool carrier show when the imple-ment is locked. Auto Plus is connected by using the same 3rd service function in a different way. Under the cross tube, in a protected location, a valve for switching this on and off can also be found, built together with the Plus Compact Valve. This can be activated from inside the cab, which means that the driver controls the flow of oil between Auto Plus and 3rd service.

Combi tool carrierUsers who want to have stronger, more versatile implements and at the same time use older imple-ments, can install one of our Combi tool carriers as an optional extra, which jointly cover most loader makes and hook types.

Multi Doc 4™

The four hydraulic hoses are connected in no time at all. Multi Doc 4 ensures that problems such as in-correct connection, oil leaks or overpressure in the hoses never arise. The risk of dirt in the tractor’s hydraulics and transmission is also avoided thanks to the smooth connectors that are easy to clean.

Multi Doc 2™

A very useful aid when the front loader is fitted with either a 3rd or a 4th service. Anyone who has tried to connect a hydraulic implement that has stood in the sun all day will testify to this. With one simple operation, the implement hydraulics are connected without difficulty, even under pressure. Work can therefore start within seconds. Like Multi Doc 4, Multi Doc 2 has smooth con-nectors that protect the tractor against dirt.

A good investmentPlusDrive shock absorbers protect both drivers and their loads. When driving on uneven terrain, the tractor is more comfortable and offers better manouverability. A very sensible optional extra that also reduces unwelcome strains on the vital parts of the tractor (read more on page 4).

Extended reachTrima Plus can also be supplied with longer bearing boxes to suit specific circumstances, providing ad-ditional reach, for example, over lorry sides. Lifting height, lifting force and other specifications are other-wise unaffected.

ElectroDrive CDC™

Improve comfort and efficiency by installing ElectroDrive CDC in the tractor’s cab. The electrical and proportionally functioning CDC (Canbus Digital Control) provides front loader operation with fingertip control, right out to the far end of the implement. If the front loader is equipped with hydraulic implement locking, 3rd and 4th services, or electrical connection and disconnection of PlusDrive, these functions can also be handled using the compact joystick. In the case of more demanding appli-cations, a “slow” function can be activated. ElectroDrive CDC can also be programmed for specific tasks, such as when bale wrapping. The implement is then opened and closed using the joystick’s sideways movements. Similarly, individual needs for the tractor’s hydraulics can be programmed. As ElectroDrive CDC can be installed together with an adjustable armrest, the working position can be continually regulated in order to avoid stresses on the operator’s shoulders, neck and wrists.

”Accessories that give even more. That is Trima”

Depressurised quick-couplingsThe third service is integrated in the Plus Compact Valve. The 4th service can also easily be connected. All valves and cables are well protected under a panel. Through carefully positioned hoses, the quick-couplings are routed to the left side of the tool carrier, ensuring a more comfortable working position. Thanks to a new design, the quick-couplings are also depressurised, further simplifying your work.

12

Because it works!

131312

Anytime, anyplaceWith a Trima Plus and a bucket equipped with its unique Non-Drop Design, you can change the landscape in no time

Tractor, Trima Plus and a trailerYou need nothing else to bring bales back to the yard. Especially if the front loader has a high lifting capacity.

As a forklift truckHere, the perfect mechanical parallel linkage has the chance to show what it can do. Yet another reason why Trima Plus is difficult to do without on an efficient farm.

”Ready for everything. That is Trima”

Instead of a bad backA couple of tons of stones disappear quickly with the aid of a stone fork and Trima Plus, with perfect visibility from the driver’s seat.

Great careLarge bags require safe, accurate handling. With Trima Plus, the ten thousandth bag can be moved with the same precision as the first.

Do it yourselfAnd save the expense. A powerful loader and an ef-ficient grab can load many tons.

The new Trima Plus loader range provides front loaders for just about every tractor and requirement. More powerful than ever before and with larger crowd and dump angles, they are ready for higher lifting heights and demanding applications. All mate-rial qualities are of the highest standard and the manufacturing tolerances are very narrow, resulting in an overall solution that is extremely reliable - a fact that has been demonstrated while undergoing harsh and repeated tests. All in all, Trima Plus is a formidable partner for the tractor. Secure and robust, with nothing but well thought-out technical solutions. Most things can be done better with a Trima Plus. Hard-working operators deserve nothing less.

14

Because it works!

15

Every time a farmer sits down at the dinner table in good time and in a good mood, there is an effective team in the background. Outside in the yard are two reliable work colleagues - the tractor and the front loader. A front loader that is well-developed to meet the user’s needs: good visibility from the driver’s seat, ready to obey the smallest lever movements, adapted for the tractor’s hydraulic capacity, exceptional damping capacity, capable of rapid implement changes and incorporating user-friendly technology.

Trima Plus is designed by engineers who are familiar with the farmer’s conditions and who understand the tractor’s full potential. It is therefore also easier to come home alert after a long day at work.

”Home in plenty of time. That is Trima”

A counter-weight must be used for safety reasons, normally approximately 800 kg. Contact Trima for more precise details. Crowd and dump angles can vary slightly depending on the type of implement. Trima’s loaders are CE marked and comply with the Machine Directive’s rules and regulations. The regulations describe how the machine should be designed with regard to health, safety and the environment. Technical data can vary depending on tractor model.* Varies depending on implement.

Parallel linked loadersLoader model +2.0 P +3.0 P +4.0 P +5.0 P +6.0 P +7.0 P

Tractor size hp 50-80 60-100 80-120 100-150 120-190 >150 kW 37-60 45-75 60-90 75-112 80-142 >112Lifting height at arm centre, m 3.50 3.75 4.00 4.25 4.50 4.75Lifting height under implement, m* 3.25 3.50 3.75 4.00 4.25 4.50

Lifting capacity, at arm centre at 185 bar oil pressureAt ground level kg 1800 2300 2400 2700 2850 3500Full height kg 1500 1900 2000 2300 2350 2550

Lifting capacity, 800 mm from arm centre at 185 bar oil pressureAt ground level kg 1500 1900 2050 2300 2500 3000At height 1.5 m kg 1400 1750 1900 2200 2350 2800Full height kg 1200 1550 1700 2000 2100 2250

Max. tear-out force kg 800 mm from arm centre 1900 2800 2800 3300 3800 3800Crowd angle* 45° 43° 44° 44° 43° 41°Dump angle* 58° 59° 55° 53° 52° 53°Weight kg 521 585 621 712 760 808

Non parallel linked loadersLoader model +1.0 +2.0 +3.0 +4.0 +5.0

Tractor size hp 50-70 50-80 60-100 80-120 100-150 kW 37-52 37-60 45-75 60-90 75-112Lifting height at arm centre, m 3.20 3.50 3.75 4.00 4.25Lifting height under implement, m* 2.95 3.25 3.50 3.75 4.00

Lifting capacity, at arm centre at 185 bar oil pressureAt ground level kg 1900 2200 2700 2800 3100 Full height kg 1500 1750 2200 2300 2600

Lifting capacity, 800 mm from arm centre at 185 bar oil pressureAt ground level kg 1200 1400 1750 1900 2150At height 1.5 m kg 1100 1300 1650 1800 2050 Full height kg 950 1150 1450 1600 1850

Max. tear-out force kg800 mm from arm centre 1850 1850 2700 2700 3200 Crowd angle* 41° 45° 43° 44° 44°Dump angle* 55° 58° 59° 55° 53°Weight kg 436 450 515 554 628

Lifting force at arm centre

Lifting force 800 mm fromarm centre

Tear-out force 800 mm fromarm centre

800 mm

16

Because it works!

17

+2.0 P +3.0 P +4.0 P

+5.0 P +6.0 P +7.0 P

0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500 0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500 0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500

0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500 0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500 0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500

Trima parallel linked loaders




800 mm

Tractor size 50-80 hp 37-60 kW

Lifting height at arm centre 3.50 m

Lifting capacity at arm centre At ground level 1,800 kg Full height 1,500 kg

Lifting capacity, 800 mm from arm centre at 185 bar oil pressure At ground level 1,500 kg At height 1.5 m 1,400 kg Full height 1,200 kg

Max. tear-out force 800 mm from arm centre 1,900 kg

Weight excl. subframe 521 kg





Max. tear-out force 800 mm from arm centre 2800 kg




















Tractor size > 150 hp > 112 kW






18

Because it works!

19

+1.0 +2.0 +3.0

+4.0 +5.0

0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500 0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500 0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500

0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500 0 500 1000 1500 2000

4

3

2

1

M

kg30002500 3500

Trima non parallel linked loaders




800 mm




Lifting capacity, 800 mm from arm centre at 185 bar oil pressure At ground level 1,200 kg At height 1.5 m 1,100 kg Full height 950 kg



























20 21

Because it works!Because it works!

21

All drivers know that it is the implement that does all the work.

In order to satisfy our customers’ expectations, we invest considerable resources in developing implements that do justice to the best front loaders on the market.

Accept no compromises. Choose Trima for implements and enjoy many years’ ef-ficiency with no problems along the way.

”Thirteen pages of excellent implements, made for profes-sionals. That is Trima”

22

Because it works!

23

A

B

C

The loader cannot function without implements Every day of the year our loaders are operating in agriculture, industry, contracting and public services. Without good-quality, versatile implements, the loaders would not be as useful. This is why we invest considerable resources in developing implements that do the loaders justice. This investment and effort has resulted in us also being the world’s largest producer of implements for front loaders.

Buckets

Buckets

Implement hooks for freedom of choiceOur implements have alternative implement hooks that are suitable for most loader makes.

A: Euro

Implement hooks suitable for Trima with Euro Tool carrier, Quicke series Q and other loader makes with Euro implement tool carriers.

B: SMSAdapted for Trima/Bergsjö with SMS tool carrier, Quicke Combi tool carrier, Kellve/Vreten/Howard as well as other loaders with SMS tool carrier.

C: Ålö type 3

Suitable for fully hydraulic loaders that preceded Quicke Serie Q.

Some implements are also suitable for loaders with Volvo BM type tool carrier.

1 2

3

4

6

5

All buckets are conical and are therefore easy to fill, as the material does not need to be pressed into the bucket. The conical, ”hopper-shaped” design also allows rapid and complete emptying of the bucket. No matter what your needs are or what demands you stipu-late, you will be able to find your new bucket in our range. There are six different models and a total of 21 different variants. There is also a special, high tip bucket and a grading bucket.

Non-drop designIt has been a natural objective to design and produce a bucket that does not allow spillage. What’s the point of having a bucket

with a large volume if it cannot be properly filled, or if it spills material? Our buckets therefore have laser-cut ends. As a result, it is possible to create a bucket design where the rear edge and in particular the front edge are especially high. It is now possible

to completely fill the bucket. You have complete control over the material, and the bucket does not drop any material.

A bucket is not just a bucket

The non-spill bucketWe all know that today’s buckets are subjected to larger loads and more hours of operation than before. Both tractors and front loaders have been made larger and more powerful. The buckets need to be wider and hold a larger volume.

We have therefore chosen an even stronger and better grade of steel. In addition, we use profile-pressed and laser cut sheet-metal.

This unifies the need for extra strength with the desire for an attractive design.

1. The buckets have a round bottom and a conical shape. Numerous small bends make the bucket strong and the coni-cal design allows simple filling and complete emptying.

2. In order to achieve even greater torsional strength and stability, the wider buckets have been supplied with an extra, profile-pressed, double back plate (not on the L and LV models). With the aid of a special overlap design, the HV buck-ets now have a hole profile along the implement hooks, which makes these buckets stronger and more stable.

3. The upper edge of the bucket back is pressed in a U-profile. In this area on the HD buckets there is a further welded angle profile along the length of the bucket.

4. The ends have a profile extrusion that makes the sides even stronger (not on the L and LV models). At the bottom is a welded triangular wearing piece, which simultaneously stabilises the cutting edge. On the HD buckets, this wearing piece runs all the way up along the end side.

5. All buckets have extremely strong cutting edges (500 Brinell). Depending on bucket model and size, 12, 16 or 20 mm thick and 100, 150 or 200 mm wide cutting edges are used. Together with the parallel reinforcing bars, the bucket bottom consequently extremely strong, torsionally stable and hard-wearing.

6. The implement hooks also contribute to a strong construction. Note that both hooks and locking holes are located along a bend. Depending on bucket model and size, there may be a double profile inside the bucket.

24

Because it works!

25

Series HT 135HT 160HT Volume (heaped) 0.54 m3 0,65 m3

Width 135 cm 160 cm Depth 81 cm 81 cm Height 75 cm 75 cm Cutting edge WxT 150/16 mm 150/16 mm Number of teeth 6 7 Weight 152 kg 172 kg

Series H 135H 160H Volume (heaped) 0.54 m3 0,65 m3

Width 135 cm 160 cm Depth 81 cm 81 cm Height 75 cm 75 cm Cutting edge WxT 150/16 mm 150/16 mm Weight 147 kg 166 kg

Buckets

Buckets

Series HD

In the emptying position, the frontloader’s effective emptying stop ensures controlled and complete emptying of the implement. Note also how the “boome-rang-shaped” link on the frontloader contributes to a maximum emptying angle.

Buckets

Buckets

The soil bucket - the most popular in the range - can do everything. The short bucket bottom makes the bucket strong and well suited to heavier tasks. The three large buckets have an extra profile and round pressed back plate across the full width.

Series H Series HT

Soil bucket with teeth. Same design as series H.

Contracting bucket. The very strongest buckets in the series. The starting point is the H bucket. On the 210, 240 and 260, the metal is 20 % thicker however. In addition, the HD buckets have a more powerful cutting edge, a wider, longer floor reinforce-ment, an extra angle reinforcement on the inside of the bucket along the implement hooks, as well as an angled wearing rail on the rear of the bucket.

Series HD

Series HT 185HT 210HT Volume (heaped) 0.72 m3 0.82 m3

Width 185 cm 210 cm Depth 81 cm 81 cm Height 75 cm 75 cm Cutting edge WxT 150/16 mm 150/16 mm Number of teeth 8 9 Weight 211 kg 259 kg

A strong material and snow bucket. The series is aimed at users who require a large volume. The generous volume measurements are achieved by designing the bucket deeper and taller. All models have double profiles in the bottom as well as along the implement hooks. There is consequently extra strength where the stresses are greatest.

Series HV Series L

Light bucket. If the bucket is only to be used for lighter duties, the L bucket is an excellent choice. The bucket is designed for customers who value function-ality ahead of technical benefits. The price is therefore extremely competitive.

Light Volume bucket. This bucket series is suitable for handling grain, manure, grass seeds, wood chips and other materials with a low volume weight. The buckets have two vertical reinforcements along the implement hooks.

Serie LV Series H 185H 210H 240H

Volume (heaped) 0.72 m3 0,82 m3 0,95 m3

Width 185 cm 210 cm 240 cm Depth 81 cm 81 cm 81 cm Height 75 cm 75 cm 75 cm Cutting edge WxT 150/16 mm 150/16 mm 150/20 mm Weight, kg 205 252 294

Series HD 185HD 210HD Volume (heaped) 0.72 m3 0.82 m3


240HD 260HD Volume (heaped) 0.95 m3 1.03 m3 Width 240 cm 260 cm Depth 86 cm 86 cm Height 75 cm 75 cm Cutting edge WxT 200/20 mm 200/20 mm Weight 340 kg 365 kg

Series L 130L 180L Volume (heaped) 0.51 m3 0.71 m3


Series HV 200HV 220HV Volume (heaped) 1.16 m3 1.28 m3 Width 200 cm 220 cm Depth 104 cm 104 cm Height 85 cm 85 cm Cutting edge WxT 150/16 mm 150/16 mm Weight 273 kg 294 kg

240HV 260HV Volume (heaped) 1.70 m3 1.85 m3 Width 240 cm 260 cm Depth 109 cm 109 cm Height 98 cm 98 cm Cutting edge WxT 200/20 mm 200/20 mm Weight 415 kg 443 kg

Which bucket should I choose?

Series LV 200LV 220LV Volume (heaped) 1.13 m3 1.25 m3


Areas of application H HT HV HD L LV

Lighter excavation and loading work

Loading e.g. grain, wood chips and snow

Loading of lighter materialsat high level

Heavy excavation and loading work

Work in gravel/sand,earth and stone

Contract work in gravel/sand, earth and stone

Grading work

Professional snow clearance

Grad. buck.

Hightip

Best choice Good choice

26

Because it works!

27

Buckets

The high tip bucket increases the unloading height by 120 cm. As a result, even a short, compact front loader can fill a high trailer if necessary. The bucket tips over its front edge, and it is not there-fore necessary to wait for the front edge to be lifted over the truck side before you can reverse away. This saves time and increases productivity.

High tip buckets are used for handling voluminous materials at high levels, for example for loading grain, grass seed, beet or wood chips.

High tip bucket

Stone fork - Professional

”Pick up and keep”. The distinctive design provides considerable opportuni-ties to fill the implement without dropping any stones already contained in the bucket. At the front, tines made of Hardox steel are installed that are specially angled down. After many hours of work, these can easily be replaced. The transverse profiles (50 x 100 mm) provide stability for the 30 mm thick tines. Note also that the back of this model is higher than on earlier models.

High tip bucket 230 Volume (heaped) 2,00 m3

Width 230 cm Depth 120 cm Height 120 cm Cutting edge WxT 150/20 mm Weight 480 kg

Forks

Grading bucket

A powerful grading bucket. Thanks to the low back plate and the long, strong bottom, the driver has perfect visibility to the tip of the bucket. The bucket is supplied with a 20 mm, powerful cutting edge. On the rear, below the 20 mm thick subframe plates, is a welded 10 mm thick angle iron, which reinforces the bucket for grading jobs.

Universal fork

Grading bucket 220 Volume (heaped) 0,65 m3

Width 220 cm Depth 110 cm Height 50 cm Cutting edge WxT 150/20 mm Weight 337 kg

Bale implement

Quadrogrip®

Flexibal®

Quadrogrip 200 Total width 235 cm Bale size 60-200 cm Arm length 130 cm Weight 418 kg

Quadrogrip is the best implement on the market for handling wrapped square and round bales. The implements arms are seated on 350 mm wide, extremely stable sliding plates, which move along the main frame. When stacking, it is possible to lock either the right or left arm, which makes for easier work. The sliding rails are interchangeable and made of high-quality polyethylene, which does not require lubrication. These sliding surfaces are also vertical so that dirt cannot become trapped. This results in re-duced friction, almost silent arm movements, minimal wear and a long service life.

Three implements in one

Flexibal is a strong and very versatile implement. The 125 mm thick, rotating steel tubes are mounted on two power-ful stone fork tines. The steel tubes are hydraulically adjustable sideways. When the bale is handled, the steel tubes roll carefully in under the bale. The tubes’ generous length and diameter distribute the pressure evenly over the bale. When straw or hay bales are to be transported, the steel tubes can be dismantled quickly and easily. With the tubes removed, Flexibal can also be used for pallet handling (max. 1,000 kg).

As an option Flexibal can be equipped with adjustable bale support that is installed on the back of the implement. This provides the potential to either handle larger bales or to stack bales on their ends.

Flexibal Weight 195 kg Bale size max. 180 cm

Bale support Weight 45 kg

Stone fork - Pro 150 200 Width 150 cm 200 cm Depth 100 cm 100 cm Height 73 cm 73 cm Number of bottom tines 14 18 Tine distance 11 cm 11 cm Weight 235 kg 292 kg

Without doubt the most powerful stone/universal fork on the market. On the specially hardened box section, which does not become deformed under load, powerful stone fork tines are installed. The back comprises five transverse 80 x 40 profiles. The design is incredibly torsionally rigid, at the same time as offering excellent visibility. On the sides, the forks are supplied with pow-erful Hardox teeth.

Universal fork 150 200 Width 150 cm 200 cm Height 73 cm 73 cm Tine length 98 cm 98 cm Number of bottom tines 14 18 Pin distance 11 cm 11 cm Weight 249 kg 310 kg

Multi Doc 2 Easier implem

ent changes


ent changes

28

Because it works!

29

Bale implement

Flexigrip™

Unigrip™

Storing the bales upright on top of each other reduces the risk of air and moisture penetrating into the bales.

The implements arms are housed in powerful hinged points with replaceable bushings. Both the right or left arm can be locked independently, but there is still some mobility, which makes it possible to stack the bales tightly without damaging the plastic. In addition, the implements arms are designed so that it is easy to re-verse out from the bale, and this is also an advantage when the bales are to be stacked tightly.

The uniquely curved, rounded shape together with the 90 mm thick tubes contribute greatly to the very careful handling of both vertical and horizontal bales. Note in particular the long, curved tubes, curved in one piece with no sharp edges or welded joints. The upper tube extension is a Trima speciality that provides significantly better support when the bales are handled horizontally.

Unigrip has a tested and proven design and a low net weight. It carries out the same tasks as Flexigrip. The choice between these implements depends on the individual user’s work routines. Unigrip is also well suited for smaller square bales (80 x 80 - 130-160 cm).

The implements arms distribute the pressure evenly over a large area, and this ensures careful handling of the bales. The arm tubes have a powerfully dimensioned diameter. Unigrip also has a large tube diameter and no sharp edges, so that the plastic around the bale is not damaged.

Flexigrip 160 200 For bale sizes, min.max. 120-160 cm 150-200 cm Weight 242 kg 262 kg

Unigrip 130 160 For bale sizes, min.max. 90-130 cm 120-160 cm Weight 200 kg 240 kg

Split the bale with ease and cheaply

Until now, splitting bales has entailed hard work or considerable expense. If you have a loader with dual-action lifting cylinders, you can solve the problem thanks to Silosplit.

Silosplit can both transport and split bales. When you have placed the bale where it is to be split, you place the blade across the top of the bale and press down. Both straw and silage bales fall apart in two pieces, simply and smoothly without complicated extra hydraulics. It is then easy to handle the material. Silosplit is supplied with an easy-to-use blade guard to provide protection from the sharp cutting edge.

Silosplit is naturally patented.

4TH SERVICE REQUIRED

3RD SERVICE REQUIRED

DB 4000 Weight 190 kg Number of tines 4 pcs

Silosplit M HD Weight 85 kg 110 kg Width 120 cm 120 cm Depth 140 cm 170 cm

Shredder Arm length 120 cm Hydraulic cylinder 1 ”shredder tines” 5 Weight 20 kg

Bale unwinder Width 78 cm Centre tine 110 cm Side tines, 3 pcs 55 cm Requirements for hydraulic Pressure 180 bar Flow 40 l/min Weight 160 kg

Bale implement

Silosplit® Bale unwinder

DB 2115 DB 4000

For safe handling of 2-4 bales

The bales are securely held between the tines and the upper section. In other words, there is no risk of dropping the bales during transport or stacking. The mast is both telescopic and hydraulic. The height of the upper section can vary from 95 cm to 195 cm.

Using just one implement, you can both trans-port the bale as well as tear up and distribute it. The bale unwinder is an operationally reliable implement for feeding or spreading out straw for free-range farmyard animals. The efficiency can be further increase if the implement is equipped with the hydraulically powered shredder.

Equip your front loader with 115 cm extra lifting height, so that you can stack the bales even higher. The DB 2115 is an excellent implement, particularly for those who require a high lifting height with short, manoeuvrable loaders.

Select the best equipment

Silaging in plastic bales can produce first-class silage. However, the bottleneck in this process is often the implement that has to handle and trans-port the bales. It is therefore important to select a quality product that can handle the bales in the right way. If the implement is not good enough, it can break or damages the bale plastic, and the whole process stops, expensive equipment and manpower are at a standstill and the quality of the silage is impaired.Our implements are characterised by powerful bearings in the arms, large implements areas so that the pressure is distributed optimally and the total absence of sharp edges. We accept no com-promises - quality has to be the very best.


ent changes

Grip, lift and turn the bale. Then transport it to the storage place, where stacking to at least the height of three bales is a simple matter.


ent changes

PATENT

DB 2115 Weight 200 kg Increased lifting height 115 cm Number of bales 4-5 [bale height 120 cm] Bale size max. 130 cm

30

Because it works!

31

The Square Bale Fork’s folding box section is a new and valuable safety detail. Firstly you can lock the tines in the upright position, increasing safety during transport, particularly on public roads. Secondly you get more efficient and safer handling. When unload-ing, the bales are pushed into place by the main frame. If unloading takes place at full height, the top bale is pushed into place with the aid of the upper section of the implement, without the long tines be-ing pressed down into the bales. As a result, there is no risk of the bales falling back when you reverse.

The Square Bale Fork can be supplied with two different frames. The 190 cm frame is suitable for long, large bales. The 140 cm frame is supplied with two tines as standard, although this number can be increased to a total of five.

As optional extra equipment, the Square Bale Forks can be sup-plied with a rear extension (for handling more bales) or a bag lifter (for handling large bags).

Bale spike Weight 60 kg Width 115 cm Tine length 110 cm

Square Bale Fork - standard Weight 78 kg Width 140 cm Number of tines, standard 2 pcs Tine length 82 cm or 125 cm

Extension Weight 42 kg

The completely closed design has been specially developed for maize silage and other silage types that often spill out. The se-rated blade provides fantastic cutting capacity in the silage. The back of the implement supplied with a mesh. Otherwise MG is made according to the same solid quality principles as Silocut.

Perfect silage blocks in just a few secondsSilocut is a versatile and extremely reliable implement with low maintenance costs. Thanks to the hardened cutting blades at both the front edge and in the side sections, Silocut leaves a clean cut surface in the silo. This prevents the admission of air and heat generation, critical for the quality the silage. Pay particular attention to the angled side blades that cut against the sideplate of the implement back. This function, which is not an obvious feature on implements of this type, ensures maximum cutting force, particularly when the block is to be cut free.

The box section is made of a hardened material that ensures good durability and a long service life. The tines are of the very best quality.

PATENTED SOLUTION FOR SAFE HANDLING

As the implement works best with the sharpest possible blades, there is a risk of injuries to people and animals. For this reason, Silocut is supplied with a guard that covers the front and side blades. This safety feature is only available on Silocut.

Silocut 110 150 190 Weight 345 kg 390 kg 530 kg Block size 112 x 80 x 80 cm 152 x 80 x 80 cm 192 x 80 x 80 cm max. x 80 cm x 80 cm x 80 cm Block volume, max 0.71 m3 0.97 m3 1.23 m3

Opening 80 cm 80 cm 80 cm Number of tines 9 pcs 13 pcs 16 pcs Working width 110 cm 150 cm 190 cm

Silocut MG 150 MG 190 MG Weight 480 kg 580 kg Block size 152 x 80 x 74 cm 192 x 80 x 74 cm max. x 74 cm x 74 cm Block volume, max 0.90 m3 1.14 m3

Opening 74 cm 74 cm Number of tines 13 pcs 16 pcs Working width 150 cm 190 cm

Bale implement

Square Bale Fork - Safety

Silage implements

Silocut®

Bale spike Square Bale Fork - standard

Silocut MG™

Square Bale Fork - Safety 140 190 Weight 133 kg 168 kg Width 140 cm 190 cm Number of tines, standard 2 pcs 5 pcs Tine length 125 cm 125 cm

The bale spike is particularly well suited to handling round bales. The longer tine ensures safe transport of the bale. The shorter tine prevents the bale from wobbling and rotating during stacking.

The Square Bale Fork is a simple, robust implement for both round and square bales. The tines in the box section can be installed with a separation of 80 or 130 cm. As an optional extra, the fork can be supplied with a U-shaped vertical rear extension, which helps to support the top bale.


ent changes

PATENT

32

Because it works!

33

The perfect all-round implementIf you have a diet feeder that is to be loaded with various feeds, Multibenne is the best choice. The wishes and requirements to which we have paid particular attention are that: It should be perfect for the purpose - namely silage handling. The side ends are there-fore tapering so that they can be inserted into the silage more easily. When the implement is tipped backwards, the high ends come into action, so that loose material is not lost. A relatively short bottom makes it easier to fill the entire bucket, all the way in to the back. The centre of gravity then moves closer to the tractor, and when unloading into high-sided vehicles, the bucket tip does not protrude as far into the vehicle. The closed bucket bottom and the close tine location results in reduced spillage. With the close bucket bottom, you can always completely gather up the material.

Multibenne, which is designed according to the same principles as Silograb, can handle many different types of fodder, including manure. As a result, it is not necessary to switch between implements when feeding.

Multibenne 130 150 170 190 210 230 250 Weight 280 kg 304 kg 360 kg 386 kg 423 kg 447 kg 477 kg Width 130 cm 150 cm 170 cm 190 cm 210 cm 230 cm 250 cm Volume 0.66 m3 0.76 m3 0.86 m3 0,96 m3 1.07 m3 1.17 m3 1.27 m3

Depth 80 cm 80 cm 80 cm 80 cm 80 cm 80 cm 80 cm Number of tines in the fork 7 pcs 8 pcs 9 pcs 10 pcs 11 pcs 12 pcs 13 pcs

Multigrab HD is a very powerful implement. When filling silage, the bucket tip is driven towards the silo, the powerful upper arm is pressed down through the silage and into the bucket. The special design of the teeth cre-ates a block with a good cut surface. This reduces the admission of air and heat generation in the silage. Thanks to its incredible strength, the Multigrab HD can also be used for many other demanding fork and bucket tasks.

The bucket is based on the powerful, reinforced HD bucket. The grapple arm is installed on the rear of the bucket, which also contributes to the implement’s strength. The movable, profile-pressed upper section is supplied with strong bearings, three-layer bushings and large pivot pins with stable locking. The sec-tion with the powerful Hardox teeth is botled in place. Stress and torsion forces are thereby transmitted to the entire construction. The teeth (version T) are simply botled in place with a bolt in the bucket bottom. The protective mesh means that loose material does not drop down onto the tractor (optional extra).

Maxi Grapple is used particularly in the USA and Canada for handling round bales (large opening of 2 m), loose hay, twigs and branches, loose silage, manure and for general bucket work. Teeth, protective mesh and grapple arm can easily be removed when only the bucket is to be used.

Three advantages that make a lot of difference: Our manure forks are equipped with a specially hardened box section that neither deforms nor turns when working. The tines are installed before the implement is painted - metal to metal. The tines are secured with a very high torque. All in all, you get an implement with a longer service life.

Silograb 130 150 170 190 210 230 250 Weight 250 kg 270 kg 300 kg 320 kg 355 kg 377kg 405 kg Width 130 cm 150 cm 170 cm 190 cm 210 cm 230 cm 250 cm Volume 0.69 m3 0.79 m3 0.90 m3 1.01 m3 1.11 m3 1.22 m3 1.33 m3

Depth 85 cm 85 cm 85 cm 85 cm 85 cm 85 cm 85 cm Number of tines in the fork 7+7 pcs 8+8 pcs 9+9 pcs 10+10 pcs 11+11 pcs 12+12 pcs 13+13 pcs

Multigrab HD 160 180 200 Weight 460 kg 500 kg 560 kg Width 160 cm 180 cm 200 cm Volume 0.86 m3 1.00 m3 1.14 m3

Depth 80 cm 80 cm 80 cm

Maxi Grapple 210 210 T 240 Weight 605 kg 620 kg 640 kg Width 210 cm 210 cm 240 cm Depth 81 cm 81 cm 86 cm Teeth length - 24 cm -

240 T 260 260 T Weight 655 kg 710 kg 730 kg Width 240 cm 260 cm 260 cm Depth 86 cm 86 cm 86 cm Teeth length 24 cm - 27 cm

Silage implements

Silograb®

Multibenne

Silograb is an extremely versatile implement. The close tine distribu-tion almost eliminates the spillage of silage. The tines are mounted in a specially hardened box section (approximately six times larger than standard profiles), which does not turn or deform under load. The tines fol-low a circular movement through the material, which produces the cleanest cut, the least power consumption and the longest service life for the tines. In addition the material is pressed against the back of the implement when the pins are lowered, and this means that the silage remains in place, even when driving over uneven terrain.

All models have two hydraulic cylinders. On the large models, the cyl-inders are 15 % larger. The 210 to 250 models are supplied with a mesh construction in the upper section.

Silage implements

Multigrab HD™

Manure fork 130 150 170 Weight 123 kg 136 kg 152 kg Width 130 cm 150 cm 170 cm Depth 85 cm 85 cm 85 cm Number of tines 7 pcs 8 pcs 9 pcs

190 230 Weight 165 kg 203 kg Width 190 cm 230 cm Depth 85 cm 85 cm Number of tines 10 pcs 12 pcs

Maxi Grapple™

Manure fork


ent changes


ent changes

3434

Because it works!

35

Pallet forks 1,000 kg 1,600 kg 2,500 kg

Weight 122 kg 160 kg 170 kg Max. load 1,000 kg 1,600 kg 2,500 kg Width 140 cm 140 cm 140 cm Fork length 97 cm 97 cm 120 cm Fork height 50 cm 92 cm 95 cm Fork type profi le wrought wrought

Bale spike (one short and one long tine). For installation on the pallet fork subframe.

Suitable for fork kits 1,000 kg, 1,600 kg and 2,500 kg

Weight 24 kg

Weight 85 kg

Big bag lifter Weight 118 kg Max. load 1,000 kg Width 120 cm Height 170 cm

Weight 78 kg

Pallet forks

Lifting implement

Accessories

Big bag lifter

Accessories - Pallet forks

Bale spike

Log grab attachment

Service is everything

+ In order to support our customers, Trima’s organisation, from sales staff to service personnel, focuses on the user’s need for rapid service.

+ Trima has a comprehensive service network close to the customer.

+ Spare parts are available wherever Trima is sold.

+ Our customers have access to spare parts information, instructions and other vital information via Internet.

+ Technical support is always close at hand for the customer. Continual training and information mean that all Trima represen- tatives can assist customers with considerable expertise.

+ Trima has always worked in close co-operation with users, and we are happy to receive your opinions and proposals for improvements. Our careful following-up provides important support in the development of new loaders, implements and subframes. A new Trima is always developed to meet today’s and tomorrow’s requirements!

Excellent access to spare parts, good service opportunities, well-trained service personnel and close proximity to rapid assistance are decisive for a front loader’s ef-ficiency and service life. All Trima customers should be aware that they are backed up by a solid organisation.

The upper profile is made in a single piece. This profile with holes for lateral adjustment provides robust securing of the forks. The load is distributed over a large area thanks to the wide load-bearing surfaces of the forks. With this special design, breaks in the arm are avoided and you get to operate a very stable fork that does not ”dangle”. The forks are naturally approved with a large safety margin.

For safe handling of large bags. The height of the hook above the ground is normally the same as when the bottom of the large bags is level with the lowest point of the front loader when the bags are hanging from the big bag lifter. Note the practical benefit of having the hook bent to the side. The hook can easily be seen from the driver’s seat.

The counter-weight is an extre-mely useful piece of equipment. You should remember always to have the same weight on the back of the tractor as on the front loader. With the loose implement bar, the counter-weight can be quickly put on and taken off. The counter-weight contributes to:

• better stability and weight distribution• reduced load on the front wheels and front axle• better contact with the ground, giveing improved traction

This implement can be used like the tractor’s 3-point linkage to help move some implements around the farm. Available with either Euro or SMS hooks.

3-point linkage

Weight, empty 125 kg Weight, fi lled min. 1000 kg

Counter-weight

ps.p

ondu

s: 0

409.

pho

to: j

oste

in s

keid

svol

l. r

epro

: um

erep

ro B

ild &

Med

ia

The front loaders in the brochure have extra equipment. Certain products may be optional extra equipment. Some of the products are not available on all markets. Working with front loaders and accompanying implements is not without risks. Serious injuries and damage can occur to people and materials in the event of incorrectly carried out work. Show consideration to your surroundings, use common sense and comply with local laws and regulations. Always read the instruction manual supplied carefully. Only use original spare parts and accessories. Ålö’s product range is continually being developed. We reserve the right at any time to alter specifications, prices and versions with no obligation on our part.®, ™ Trademarks of Ålö AB.

Ålö AB, SE 901 37 Umeå, Sweden Tel: +46 (0)90-17 05 00. Fax: +46 (0)90-17 05 99

www.alo.se

Best

nr 1

114

4179

Because it works!

Date post:	18-Nov-2014
Category:	Documents
Upload:	info4826
View:	160 times
Download:	3 times

Trima Leaflet

Documents