Date post: | 03-Jun-2018 |
Category: |
Documents |
Upload: | pero-lukic |
View: | 229 times |
Download: | 0 times |
of 152
8/12/2019 UMN CMXC c800_1_7619
1/152
User Manual
Crossconnect Multiplexer CMXC
UMN CMXC
A50010-A3-C800-1-7619
8/12/2019 UMN CMXC c800_1_7619
2/152
2 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
f Important Notice on Product SafetyElevated voltages are inevitably present at specific points in this electrical equipment. Some of theparts may also have elevated operating temperatures.
Non-observance of these conditions and the safety instructions can result in personal injury or in prop-erty damage.
Therefore, only trained and qualified personnel may install and maintain the system.
The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to complywith the applicable safety standards.
The same text in German:Wichtiger Hinweis zur Produktsicherheit
In elektrischen Anlagen stehen zwangslufig bestimmte Teile der Gerte unter Spannung. Einige Teileknnen auch eine hohe Betriebstemperatur aufweisen.
Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Krperverletzungen undSachschden fhren.
Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertesPersonal die Anlagen installiert undwartet.
Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Gertemssen die zutreffenden Sicherheitsbestimmungen erfllen.
Trademarks:
All designations used in this document can be trademarks, the use of which by third parties for theirown purposes could violate the rights of their owners.
Copyright (C) Siemens AG 2002.
Issued by the Information and Communication Networks GroupHofmannstrae 51D-81359 Mnchen
Technical modifications possible.Technical specifications and features are binding only insofar as
they are specifically and expressly agreed upon in a written contract.
8/12/2019 UMN CMXC c800_1_7619
3/152
A50010-A3-C800-1-7619 3
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
This document consists of a total of 152 pages. All pages are issue 1.
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.1 Structure of the Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.2 Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.3 Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121.4 Protective Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.4.1 General Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.4.2 Protection Against Excessive High Contact Voltages. . . . . . . . . . . . . . . . . 131.4.3 Components Subject to Electrostatic Discharge. . . . . . . . . . . . . . . . . . . . . 131.4.4 Handling Modules (General) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.4.5 Virus Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.5 CE Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.6 Environmental Passport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.1 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.2 Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.2.2 External Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.2.3 Internal Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.2.4 Clock Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232.2.5 Conferences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.2.6 Subrate Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.2.7 Voice Channel in Common Frequency Radio Networks. . . . . . . . . . . . . . . 252.2.8 Redundancy Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252.2.9 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262.3 Operation and Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.3.1 Access to CMXC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.3.2 Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.3.3 Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.3.4 Diagnostic Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282.4 Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282.4.1 Storage Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282.4.2 Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3 Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.2 SNUS Shelf. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303.2.1 SNUS Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303.2.2 Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323.2.3 QD2 Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333.2.4 Position and Assignment of Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 343.2.5 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403.3 Central Unit CUC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403.3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403.3.2 Supervision and Alarm Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8/12/2019 UMN CMXC c800_1_7619
4/152
4 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
3.3.3 Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503.3.4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533.4 Interface Unit PU16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543.4.2 Supervision and Alarm Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563.4.3 Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 613.4.4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643.5 Supervision Unit SUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643.5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643.5.2 Supervision and Alarm Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673.5.3 Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683.5.4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
4 Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784.1.1 Scope of the ITMN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784.1.2 Error Reports on the Installation Test Manual. . . . . . . . . . . . . . . . . . . . . . . 784.1.3 Dealing with Defective Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784.1.4 Procedure in the Event of Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784.1.5 Procedure in the Event of Serious Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . 784.2 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794.2.1 Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794.2.2 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794.3 Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 804.3.1 Sequences for Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
4.3.2 Visually Inspection (Check List) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 804.3.3 Starting the LCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 814.3.4 Commissioning of the SNUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 814.3.5 Commissioning of the SUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 824.3.6 Commissioning the CUC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 844.3.7 Commissioning the PU16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 864.3.8 Creating the Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915.1.1 Notes for Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
5.1.2 Overview of Operating Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915.1.3 Overview of Function Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 975.1.4 Network Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 985.1.5 SISA Communication Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995.1.6 Interfaces used for Operating Purposes . . . . . . . . . . . . . . . . . . . . . . . . . . 1015.2 Software Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1025.3 Configuration Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1025.3.1 SISA-V/LMXV2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035.3.2 CUC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1045.3.3 PU16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1115.4 Crossconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
5.4.1 Crossconnections 2 Mbit/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
8/12/2019 UMN CMXC c800_1_7619
5/152
A50010-A3-C800-1-7619 5
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
5.4.2 Cross Connections 64 kbit/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1255.4.3 Cross Connections 8 kbit/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1315.4.4 Conference Mode (between 64 kbit/s Time Slots only) . . . . . . . . . . . . . . 135
5.4.5 Displaying the used 2-Mbit/s Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1405.4.6 Overview of the used 64 kbit/s Crossconnections . . . . . . . . . . . . . . . . . . 142
6 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1446.1 Operator Terminals for Maintenance and Fault Rectification. . . . . . . . . . 1446.2 Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1446.2.1 Hardware Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1456.2.2 Software Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1456.2.3 Adjustments for Service in System Module . . . . . . . . . . . . . . . . . . . . . . . 1456.2.4 Fault Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1456.3 Representation of Alarms in OS and LCT. . . . . . . . . . . . . . . . . . . . . . . . . 1456.4 Elimination of an Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1466.4.1 Localization of an Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1466.4.2 Alarm Elimination by Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1476.4.3 Branch to Maintenance Procedures from Alarm Lists of the ACI. . . . . . . 1476.5 Branch to Maintenance Procedure from Graphical User Interface of the
OS/LCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1476.6 Explanations of the Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1476.7 Alarm Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
7 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
8 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
8/12/2019 UMN CMXC c800_1_7619
6/152
6 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
Illustrations
Fig. 1.1 ESD Symbol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fig. 2.1 CMXC Application (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Fig. 2.2 CMXC Application in an FMX2R3.1 Ring Connection . . . . . . . . . . . . . . 18
Fig. 2.3 CMXC Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Fig. 2.4 Allocation of Alarm Contacts, Example ZA(A) . . . . . . . . . . . . . . . . . . . . 20
Fig. 2.5 CMXC Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fig. 2.6 Redundancy Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Fig. 2.7 Power Supply in Shelf SNUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Fig. 2.8 CMXC in Stand-alone Operation Mode (Example) . . . . . . . . . . . . . . . . . 27
Fig. 3.1 SNUS with Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Fig. 3.2 SNUS Front View with the DIL Switches S101 to S116. . . . . . . . . . . . . 31
Fig. 3.3 DIL Switches S105 to S116 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Fig. 3.4 DIL Switch S101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Fig. 3.5 DIL Switches S103 and S104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Fig. 3.6 Location of Connectors and Equipping of Units. . . . . . . . . . . . . . . . . . . 34
Fig. 3.7 CUC Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Fig. 3.8 CUC Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Fig. 3.9 Position of the Jumpers on the Pin Strips X401. . . . . . . . . . . . . . . . . . . 50
Fig. 3.10 PU16 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Fig. 3.11 Local Loop and Remote Loop Test Loops . . . . . . . . . . . . . . . . . . . . . . . 57
Fig. 3.12 PU16 Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Fig. 3.13 Position of the Jumpers on the Pin Strips. . . . . . . . . . . . . . . . . . . . . . . . 62
Fig. 3.14 Operation and Supervision of the System Modules inStandalone Operation Mode with the SUE (Example) . . . . . . . . . . . . . . 65
Fig. 3.15 SUE Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Fig. 3.16 SUE in a Line Network Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Fig. 3.17 SUE Operating Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Fig. 3.18 SUE Terminal Assignment 12 (F Interface) . . . . . . . . . . . . . . . . . . . . . . 71
Fig. 3.19 SUE Connector Assignment 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Fig. 3.20 Connector Assignment 10 of the SUE . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Fig. 4.1 SUE Dialog Software Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Fig. 4.2 SUE Dialog Equipment Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Fig. 4.3 SUE Dialog Alarms of SISA-V/LMXV2#... . . . . . . . . . . . . . . . . . . . . . . 84
Fig. 5.1 QD2 Structure (Example). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Fig. 5.2 SISA Structure of FastLink System. . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Fig. 5.3 Example of a SUE Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Fig. 5.4 SUE Register Card Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Fig. 5.5 CUC Register Card for Setting the Clock Synchronization . . . . . . . . . . 105
Fig. 5.6 CUC Register Card for Configuring the Alarm Supervision . . . . . . . . . 106
Fig. 5.7 CUC Register Card for Configuring the Ports . . . . . . . . . . . . . . . . . . . . 107
Fig. 5.8 CUC Register Card for Setting the ECC Operation Mode . . . . . . . . . . 108
Fig. 5.9 CUC Register Card for Activation/Deactivation of the ports . . . . . . . . . 109
Fig. 5.10 CUC Register Card for Displaying the State of the ECC Ports. . . . . . . 110
8/12/2019 UMN CMXC c800_1_7619
7/152
A50010-A3-C800-1-7619 7
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
Fig. 5.11 CUC Register Card for Displaying the State of the PCI Ports . . . . . . . 111
Fig. 5.12 PU16 Register Card for setting the Operator Loop. . . . . . . . . . . . . . . 112
Fig. 5.13 PU16 Register Card for Setting the Alarm Criteria . . . . . . . . . . . . . . . 113
Fig. 5.14 PU16 Register Card for Setting the Frame structure . . . . . . . . . . . . . . 113Fig. 5.15 PU16 Register Card for Setting the Sa Bit Control . . . . . . . . . . . . . . . 114
Fig. 5.16 PU16 Register Card for Setting the Operation Mode. . . . . . . . . . . . . . 115
Fig. 5.17 PU16 Register Card for Displaying the State off all Ports. . . . . . . . . . 115
Fig. 5.18 Register Card Connections 2Mbit/s. . . . . . . . . . . . . . . . . . . . . . . . . . 117
Fig. 5.19 Register Card for Setting Filter Parameter. . . . . . . . . . . . . . . . . . . . . . 120
Fig. 5.20 Dialog for Creating Crossconnection 2 Mbit/s(Example with Filter setting Representation of Resources: FG-FE) . 121
Fig. 5.21 Dialog for Setting the Time Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Fig. 5.22 Dialog for Setting the Switching Criteria . . . . . . . . . . . . . . . . . . . . . . . 122
Fig. 5.23 Register Card Connections 64kbit/s . . . . . . . . . . . . . . . . . . . . . . . . . 125Fig. 5.24 Dialog for Creating the Crossconnection 64 kbit/s
(Example with Filter setting Representation of Resources; FG-FE) . 128
Fig. 5.25 Displaying of the Time Slots assigned to a Group (Example). . . . . . . 129
Fig. 5.26 Dialog for Creating the Crossconnection 64 kbit/s(Example with Filter settingRepresentation of Resources; Module-Port-TS) . . . . . . . . . . . . . . . . 130
Fig. 5.27 Register Card Connections 8kbit/s. . . . . . . . . . . . . . . . . . . . . . . . . . 131
Fig. 5.28 Dialog for Creating the Crossconnection 8 kbit/s(Example with Filter setting Representation of Resources; FG-FE) . 134
Fig. 5.29 Dialog Configure Conferences - CMXII-CAS (Example) . . . . . . . . . . 136
Fig. 5.30 Dialog Add data Conference - CMXC#...:CUC#... . . . . . . . . . . . . . . 138
Fig. 5.31 Register Card 2Mbps Port Usage (Example) . . . . . . . . . . . . . . . . . . 140
Fig. 5.32 Register Card 64Kbps CC Overview (Example). . . . . . . . . . . . . . . . 142
Fig. 6.1 Elements of the Maintenance Procedures. . . . . . . . . . . . . . . . . . . . . . 148
8/12/2019 UMN CMXC c800_1_7619
8/152
8 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
Tables
Tab. 1.1 Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Tab. 2.1 Structure of a PCI Time Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tab. 2.2 PCI Frame Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tab. 2.3 Conference Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Tab. 3.1 SNUS Overview of Addressing and the Units. . . . . . . . . . . . . . . . . . . . . 32
Tab. 3.2 Assignment of Connectors X141 (left and ) X142 (right) . . . . . . . . . . . . 35
Tab. 3.3 Terminal Assignment of Jacks X101, X102 and X121. . . . . . . . . . . . . . 35
Tab. 3.4 Terminal Assignment of 9-Contact Jacks X143 and X144. . . . . . . . . . . 36
Tab. 3.5 Terminal Assignment of Jacks X122 and X131 . . . . . . . . . . . . . . . . . . . 37
Tab. 3.6 Terminal Assignment of Jacks X109, X110, X 113, X114, X129, X130,X133, X134 and X115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Tab. 3.7 CUC Signaling the active Operating Mode . . . . . . . . . . . . . . . . . . . . . . . 42
Tab. 3.8 CMXC Indication of the Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . 43Tab. 3.9 CUC Indication of the standby Operating Mode . . . . . . . . . . . . . . . . . . . 43
Tab. 3.10 CUC Alarm Table (active) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Tab. 3.11 CUC Alarm Table (standby). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Tab. 3.12 CUC Connector (bottom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Tab. 3.13 CUC Connector (top) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Tab. 3.14 PU16 Signaling the Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Tab. 3.15 PU16 Alarm Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Tab. 3.16 PU16 Connector (bottom). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Tab. 3.17 PU16 Connector (top) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Tab. 3.18 SUE LED Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Tab. 3.19 Settings on Switches S1 and S2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Tab. 3.20 Settings on Switch S3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Tab. 3.21 Configuration of the T Interfaces (Switch S4) . . . . . . . . . . . . . . . . . . . . . 69
Tab. 3.22 ECC Configuration (Switch S4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Tab. 3.23 Assignment on Test Jack X4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Tab. 3.24 Assignment on Test Jack X5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Tab. 4.1 Pin Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Tab. 4.2 Sequence of the Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Tab. 4.3 Shelf Equipping with SUE and Units for CMXC. . . . . . . . . . . . . . . . . . . 81
Tab. 4.4 Sequence for Creating 2-Mbit/s Cross Connections. . . . . . . . . . . . . . . . 88
Tab. 4.5 Sequence for Creating 64-kbit/s Cross Connections . . . . . . . . . . . . . . . 89
Tab. 4.6 Sequence for Creating 8-kbit/s Cross Connections. . . . . . . . . . . . . . . . 89
Tab. 4.7 Sequence for Creating Conferences. . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Tab. 5.1 Overview of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Tab. 5.2 Network Element CMXC and its associated Function Groups. . . . . . . . 97
Tab. 5.3 Name of the Function Groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Tab. 5.4 F Interface of the System Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Tab. 5.5 Correlation between Unit and Load Files. . . . . . . . . . . . . . . . . . . . . . . 102
Tab. 5.6 Configuration Parameters for the Network Elements. . . . . . . . . . . . . . 103
Tab. 5.7 List Entries in the Clock Priority List. . . . . . . . . . . . . . . . . . . . . . . . . . . 105
8/12/2019 UMN CMXC c800_1_7619
9/152
A50010-A3-C800-1-7619 9
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
Tab. 5.8 Explanation of the Buttons in the CUC Register Card Clock sync. . . 106
Tab. 5.9 Explanation of the CUC Register Card ECC Alarm Criteria . . . . . . . 106
Tab. 5.10 Explanation of the CUC Register Card Frame . . . . . . . . . . . . . . . . . 107
Tab. 5.11 Explanation of the CUC Register Card ECC Mode . . . . . . . . . . . . . . 108Tab. 5.12 Explanation of the CUC Register Card General . . . . . . . . . . . . . . . . 109
Tab. 5.13 Explanation of the CUC Register Card ECC Status . . . . . . . . . . . . . 110
Tab. 5.14 Explanation of the CUC Register Card PCI Status. . . . . . . . . . . . . . 111
Tab. 5.15 Explanation of the PU16 Register Card General. . . . . . . . . . . . . . . . 112
Tab. 5.16 Explanation of the Pu16 Register Card Alarm Criteria . . . . . . . . . . . 113
Tab. 5.17 Explanation of the PU16 Register Card Frame . . . . . . . . . . . . . . . . . 114
Tab. 5.18 Explanation of the PU16 Register Card Clock Control . . . . . . . . . . . 114
Tab. 5.19 Explanation of the PU16 Register Card General. . . . . . . . . . . . . . . . 115
Tab. 5.20 Explanation of the PU16 Register Card Status View. . . . . . . . . . . . . 116
Tab. 5.21 Explanation of the Register Card Connections 2Mbit/s . . . . . . . . . . . 117Tab. 5.22 Explanation of the Buttons on the Register Card
Connections 2Mbit/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Tab. 5.23 Switchable Function Groups for 2Mbit/s Cross Connections. . . . . . . . 123
Tab. 5.24 Assignment of IPMB64/2 to Associate TP . . . . . . . . . . . . . . . . . . . . . . 123
Tab. 5.25 Explanation of the Register Card Connections 64kbit/s . . . . . . . . . . 125
Tab. 5.26 Explanation of the Buttons on the Register CardConnections 64kbit/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Tab. 5.27 Switchable Function Groups for 64kbit/s Crossconnections. . . . . . . . 129
Tab. 5.28 Explanation of the Register Card Connections 8kbit/s . . . . . . . . . . . 131
Tab. 5.29 Explanation of the Buttons on the Register CardConnections 8kbit/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Tab. 5.30 Switchable Function Groups for 8kbit/s Cross Connections . . . . . . . . 135
Tab. 5.31 Explanation of the Register Card Data Conferences. . . . . . . . . . . . . 136
Tab. 5.32 Explanation of the Buttonson the Register Card Data Conferences . . . . . . . . . . . . . . . . . . . . . . 137
Tab. 5.33 Explanation of the Register Card 2Mbps Port Usage. . . . . . . . . . . . 140
Tab. 5.34 Explanation of the Buttons on the Register Card2Mbps Port Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Tab. 5.35 Explanation of the Register Card 64Kbps CC Overview . . . . . . . . . . 142
Tab. 5.36 Explanation of the button on the Register Card64Kbps CC Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Tab. 6.1 Determining the TOS Address from the DCN Alarm Address . . . . . . . 147
Tab. 6.2 Alarm Association . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
8/12/2019 UMN CMXC c800_1_7619
10/152
10 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
8/12/2019 UMN CMXC c800_1_7619
11/152
A50010-A3-C800-1-7619 11
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
1 IntroductionIn this Manual, an overview about the components and their interworking in the accessnetwork of the Crossconnect Multiplexer CMXC is given. Function, commissioning,operation and maintenance are described in detail. The operation is done via the graph-ical interface of the Operating System (OS). This is the Domain Manager ACI Softwareup version 8.2. For the ACI DM V8.2, there is a separate documentation available (seeSection 1.3 "Additional Documentation").
1.1 Structure of the Manual
The manual consists of the following Sections: Introduction System overview Components
Commissioning Operation Maintenance and trouble shouting.
Technical Description The Technical Description (system overview and components) contains special infor-mation about the CMXCs Modules and the shelf, i. e. interfaces, Technical Data and theconnector assignment.
Commissioning The Commissioning describes all the procedures and measurements for activating theinstalled system, including step-by-step instructions to commissioning the SystemModule CMXC.
Operation This section offers a guide line to use the operating procedures for configuring and for
creating the crossconnections.Maintenance The procedures which expedite the re-establishment of normal operating state after a
malfunction has occurred in the CMXC can be find out via the operating system byBranch to Maintenance. The section Maintenance gives an overview of the possiblemalfunctions and contains a guideline for the using of Branch to Maintenance.
1.2 Typographical Conventions
In all sections of this manual, the following conventions are applied:
Style of Representation Meaning
Courier Inputs and outputsExample: EnterLOCALas the server name
Command not found
Italics Variables
Example: namecan be up to eight letters long.
Italics Variables fin procedures and title bas
Example: General NE Parameter. :CUC#...
Boldface Special emphasis
Example: This name may notbe deleted
Tab. 1.1 Typographical Conventions
8/12/2019 UMN CMXC c800_1_7619
12/152
12 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
1.3 Additional Documentation
In addition, following documentation are used: User Manual AccessIntegrator ACI DM version V8.2, UMN
SIEMENS Kit No. A50010-T3-A808 User Manual Flexible Multiplexer FMX2R3.1, UMN
SIEMENS Ordering No. A50010-A3-C700-*-7619. Project (planning) documentation.
Quotation marks Labels on the user interface (e.g. windows, menu items, buttons)
Example: Activate the OK button
Make a selection in the File menu.
Key combinations
Example: +
Successive menu items
Example: FileClose
iAdditional items of information
!Warnings at critical points in the activity sequence
Style of Representation Meaning
Tab. 1.1 Typographical Conventions (Cont.)
8/12/2019 UMN CMXC c800_1_7619
13/152
A50010-A3-C800-1-7619 13
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
1.4 Protective Measures
1.4.1 General Notes
This section contains a summary of the most important requirements with regard to pro-tection of people and equipment. It does not claim to be complete. The installation in-structions listed are shown in detail in the relevant Installation Manuals.
All assembly, installation, operation and repair work may only be undertaken by properlytrained and qualified personnel.In the event of any injury (e.g. burns and acid burns) being sustained, seek medical helpimmediately.
1.4.2 Protection Against Excessive High Contact Voltages
When handling the power supply or working on it, observe the safety measures de-scribed in the specifications of the European Norm EN 50110, part 1 and part 2 (Oper-ation of electrical Systems) and the valid national country specific standards.
1.4.3 Components Subject to Electrostatic Discharge
Fig. 1.1 ESD Symbol
When packing or unpacking, touching pulling or plugging plug-in units bearing the ESDsymbol, it is essential to wear a grounding bracelet, which should be grounded to an rackor shelter when working on it. This ensures that the units are not subject to electrostaticdischarge.
Under no circumstances should the printed conductors or components of modules betouched. Take hold of modules by the edge only.
Once they have been removed, modules must be placed in the conductive plasticsleeves intended for them, and kept or dispatched in the special boxes or transport cas-
es bearing the ESD symbol.In order to avoid further damage to defective modules, they should be treated with thesame degree of care as new ones.
Modules which are accommodated in a closed and intact housing are protected anyway.
European standard EN50082-1 provides information on the proper handling of compo-nents which are subject to electrostatic discharge.
!Slide-in units bearing the symbol in Fig. 1.1, are equipped with components subject toelectrostatic discharge, that is to say the relevant safety provisions must be adhered to.
8/12/2019 UMN CMXC c800_1_7619
14/152
8/12/2019 UMN CMXC c800_1_7619
15/152
A50010-A3-C800-1-7619 15
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
1.6 Environmental Passport
The aim of this environmental passport is to provide you with the most important envi-ronmentally-relevant information for this product. This means you can be sure that you
have selected a supplier who develops, produces, packs and ships their products in anenvironmentally-compatible way.
Product origination process
Even at the product origination stage we pursue the aim of minimizing the adverse ef-fects on the environment: We systematically record all product-related environmental requirements and take
account of these both in the product definition and in its development. Protecting the environment is a matter of course in our day-to-day work. This in-
cludes minimizing the consumption of paper by using the latest technologies (e.g.Internet, e-mail, database, 4:1 paper printouts) as well as multi-separation, heat in-
sulation and intelligent use of energy. We coordinate all environmental activities via a certified environmental manage-ment system which complies with ISO 14001. It is checked in accordance with theGerman certification body DQS (Deutsche Gesellschaft fr Zertifizierung von Man-agementsystemen mbH), quality and environment assessors. Certificate registra-tion No.: 66749-01.
Naturally we at Siemens are conscious of the fact that expenditure for environmentalprotection measures must be kept within an economically justifiable framework. After all,we still want to offer you this product with a price/performance ratio which is attractiveto you.
Manufacturing
Production facilities are equipped with the very latest, environmentally-friendly produc-tion machinery. Because of their minimal adverse effects on the environment theseplants can be operated without the need for special permits or notification. However theappropriate measures for reducing emissions are still taken in accordance with the stateof the art: Solder systems with condensate traps minimize both the deposition of solvents at
the workstation and emissions into the atmosphere Our manufacturing processes are completely free of CFCs, volatile CHCs (chlorinat-
ed solvents) and toxic substances. The heat generated from producing compressed air will be used for heating walkable
floor surfaces. Module production is practically waste-water-free since the use of low-residue fluxes
obviates the need for cleaning processes. Far more than three quarters of all production waste is fed back into the secondary
resources cycle. Only 0.5% of the production waste has to be disposed of as specialwaste.
Transport/shipping
The systems made by our company are shipped exclusively in environmentally-friendlypackaging: pesticide-free wooden packing cases, collapsible, reusable Cardboard boxes
Filling/stuffing: air cushions with polyethylene envelope
8/12/2019 UMN CMXC c800_1_7619
16/152
16 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
The Green Dot symbol for all packing for private end customers as a sign of ourinvolvement in Germanys dual system.
Energy consumption
The ever greater level of integration in components has significantly reduced the energyconsumption of the systems without affecting the normal features (number of channels,techn. refinements etc.).
The values for electricity consumption stated in the specification are maximum values.In normal mode they are far below the figures stated.
Power-down circuits also reduce energy consumption.
Taking back the product
Currently it is only possible to take back products when this has been regulated by priorcontract agreements.
Waste disposal
Basically the systems from Siemens Wireline Access Networks are produced withoutany hazardous or forbidden substances such Cadmium, PCBs, CFCs or such like. Oncethis product has reached the end of its useful life, it can be fraction separated and dis-posed of without hesitation in accordance with the current state of the art.
List of materials: Casing: Aluminum, steel, ABS plastic (flame-resistant)
Surface coating only when this is required by the customer. Modules: Normal electronic components (disposal as
electronic waste). The board material contains brominated
flame retardants. The following are to be disposed ofseparately: Electrolytic capacitors, LCDs and mechanicalcomponents (heat sinks)
Cable Copper Connectors: Gold, plastic
Special features of specific components are listed in the enclosed dismantling guide.
All information is provided on a voluntary basis and far exceeds that required by law.Should you have anyother questionsabout our quality and environmental management,please send an e-mail to the following address:[email protected]
Siemens AG, 2002
ICN Wireline Access Networks
Munich/Greifswald
8/12/2019 UMN CMXC c800_1_7619
17/152
A50010-A3-C800-1-7619 17
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
2 System Overview
2.1 ApplicationThe CMXC crossconnect multiplexer is a compact solution to establish small networknodes at 8-kbit/s, 64-kbit/s and 2-Mbit/s level. It supports up to 48 2-Mbit/s ports andmakes it possible to switch 64-kbit/s channels between these ports without blocking.
The CMXC connects communication paths between the following signals: Max. 240 each with 8 kbit/s in the structure n 8 kbit/s (n = 1, 2 and 4) Max. 1488 each with 64 kbit/s in the structure n 64 kbit/s (n = 1 to 31)
64-kbit/s channels can be cross connected with and without signaling identification(CAS).
Max. 48 each with 2 Mbit/sThe 2-Mbit/s signals are available at 32 E1 por ts and 4 PCI interfaces
(each with 42-Mbit/s signals).Unframed 2-Mbit/s signals are switched through transparently.A frame selected from framed 2-Mbit/s signals can also be used as a referenceframe for signal processing in the CMXC.
The connections are usually bidirectional, but 2-Mbit/s and 64-kbit/s connections canalso be created unidirectionally or as a loop (loopback).
Fig. 2.1 CMXC Application (Example)
The crossconnect multiplexer offers the following possibilities: Switching a maximum of 48 framed (with and without CRC4) and unframed 2-Mbit/s
signals with up to 1488 switchable 64-kbit/s time slots Group switching of n 64-kbit/s time slots by complying with the frame integrity Bidirectional switching of up to 30 time slots (64 kbit/s) via a subrate matrix to switch
n 8-kbit/s channels (n = 1, 2 and 4) by changing the signal delays without process-ing the identification
Establishing scheduled jobs and path protection on 2-Mbit/s level
LE2 3P7
P8
SMX1/4c STM-1/STM-4
CMXC
ZS1
ZS60
FMX2R3.1
LE2 1
.
.
.
.
.
.
.
.
.
.
.
.
P1 P17
P3
P32
P2
P4
P1
P16
P9
P16
.
.
.
.
.
.
E1, 2 Mbit/sG.703
E1, 2 Mbit/sG.703
8/12/2019 UMN CMXC c800_1_7619
18/152
18 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
Switching for Sa bits 4 to 8 to be used as the clock control bit in ring structures Providing 4 ECC channels (two synchronous with 64 kbit/s and two asynchronous
with 9.6 kbit/s) for remote control in TMN (telecommunications Management Net-works) systems
Creating conference calls for speech signals (30 subscribers in 10 conferences) withdigital conference of the identification
Digital conferences for 64-kbit/s time slots with data signals (max. 10 conferenceswith up to 30 subscribers) with digital conference of the identification
Synchronization to one of 7 freely configurable clock sources (2-Mbit/s data lineclocks) or central clock pulse T3
Supervision of the connection quality according to G.821/G.826 Providing the alarm signaling contacts ZA(A), ZA(B) Software upgrade via the QD2 interface Restore and backup configuration data Complying with the requirements ITU-T G.812 and G.796.
Fig. 2.2 CMXC Application in an FMX2R3.1 Ring Connection
For an FMX2R3.1 application it is advantageous if system module FMX2R3.1 is operat-ed together with the CMXC in a ring structure. This includes: Optimum capacity utilization of the 2-Mbit/s lines in an FMX2R3.1 ring 2-Mbit/s path protection is retained in a ring structure Both 2-Mbit/s ports of the CUD unit are available in a ring structure for the transmis-
sion of basic channels Possibility of optionally cross connecting 8-kbit/s and 64-kbit/s channels Suitable structures for network management
Concentration in the CMXC such as four ECC interfaces to integrate the SNUS shelfand other system components in TMN.
CMXC
CMXC
CMXC
CMXC
FMX2R3.1FMX2R3.1
FMX2R3.1
FMX2R3.1
8/12/2019 UMN CMXC c800_1_7619
19/152
A50010-A3-C800-1-7619 19
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
2.2 Structure
2.2.1 Overview
The following units belong to Crossconnect Multiplexer CMXC: One or two central CUCs (central unit cross connect)
The central unit contains the switching matrix via which the communication pathsare connected. A second central unit is connected in parallel for module redundancy.
Up to two interface PU16 units (port unit with 16 2-Mbit/s ports)The interface unit provides the 2-Mbit/s interfaces. One or two PU16s are equippeddepending on the number of desired interfaces.
Fig. 2.3 CMXC Block Diagram
2.2.2 External Interfaces
2-Mbit/s Interfaces (E1)
16 2-Mbit/s interfaces (E1in, E1out) are established for each PU16 unit.HDB3-coded PCM signals are received and sent at the E1 interfaces. They correspondto the ITU-T recommendation G.703/6.The line impedance 75 unsymmetrical or 120 symmetrical can be set individuallyfor each interface by means of jumpers (see Section 3.3.3).
PCIS5 to 8
CUC
PU16
CUCS
PCI5 to 8PCI1 to 4
PCIS1 to 4
CCURCCURS
LSI (1 to 7)SVB
ST
SBCC
QD2-ST3in T3out
PCI9 to 12
PCIS9 to 12
ZA(A), ZA(B)
48 V
4ECC (V.11)
ZA(A), ZA(B)48 V
4ECC (V.11)
2 Mbit/s, G.703 2 Mbit/s, G.703
1
16
17
32
.
.
.
.
.
.
PU16
48 V48 V
redundant CUC
CCUR
CCURS
8/12/2019 UMN CMXC c800_1_7619
20/152
20 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
PCI Interfaces
There are four PCI links on the central CUC for external connections to other systemmodules of FastLink (for later applications) via lines not exceeding 15 m. The PCI inter-
faces are proprietary, symmetrical interfaces with levels according to EIA RS422 andterminating resistors 100 serial in the transmit direction and 150 parallel in the re-ceive direction. The frame structure and time slot allocation of PCI links are containedin Section 2.2.2.
T3 Interface
For clock synchronization, a clock signal can be fed via interface T3in and sent viaT3out. The interface is on the CUC and corresponds to the ITU-T recommendationG.703/10. The input impedance of T3in can either be connected with high-impedance(1.6 kII < 120 pF) or with low-impedance (120 symmetrical/75unsymmetrical).
A clock signal is sent at T3out if the cross connect is synchronized by T3in or E1in of an
2-Mbit/s port. The interface is designed with low-impedance and is disconnected whenswitching over to the redundant CUC.
QD2 Slave Interface
The CUC has a QD2 slave interface according to EIA RS485 which forms the TMN ac-cess to the network element CMXC. Because the number of subscribers is not fixedfrom the start due to the bus structure and the possibility of different equipping, the in-terface is closed with high-impedance on the unit. Depending on the QD2 structure, thebus termination must be suitably fitted on the outside. Care must be taken that two busloads are active for redundant equipping of CUC (maximum possible number is 32).One QD2 address applies to active and standby CUCs.
ECC Interfaces
The ECC interfaces transmit control information from higher-level and to remote systemcomponents. The control information is integrated in an ECC channel (64-kbit/s timeslot) within a 2-Mbit/s signal. The central CUC provides four ECC interfaces. They con-form to ITU-T V.11 and can be accessed via the connector panel.
Two ECC interfaces are provided as synchronous interfaces (with clock lines) and twoas asynchronous interfaces (without clock lines). The synchronous interfaces are oper-ated with 64 kbit/s. Signal distortions of +5% to 10% are obtained for asynchronous op-eration with 9.6 kbit/s (or lower bit rates).
Alarm Contacts
The alarm contacts are arranged on central units CUC and are used to signal alarmmodes of the CMXC system module. They are established as floating relay contacts.Fig. 2.4 shows the allocation of alarm contacts for ZA(A). The alarm contacts ZA(B) aredesigned in an equivalent manner.
Fig. 2.4 Allocation of Alarm Contacts, Example ZA(A)
ZA(A)_AZA(A)_R
ZA(A)_U(PUP)
ZA(A)
To theconnector panel
8/12/2019 UMN CMXC c800_1_7619
21/152
A50010-A3-C800-1-7619 21
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
Alarm contact ZA(A) optionally signals prompt alarms (A alarm) or service alarms(S alarms) and the selection is menu-controlled. Alarm contact ZA(B) signals deferredalarms (B alarm). The software of both CUCs activates these alarms.
The criteria to release A, B and S alarms are given in the alarm table (see Section 3.3.2).
CCUR Interface
The symmetrical interface lines CCUR (according to RS485), signal redundancy opera-tion. Each CUC signals its active or standby mode via a separate line of the externalequipment so that these can switch over their PCI bus drivers.
2.2.3 Internal Interfaces
PCI Interfaces
The PCI interfaces transmit useful data between the CUC and units PU16. They also
distribute the clocks of the master clock from the CUC to the peripheral equipment.A PCI link establishes a point-to-point connection between the CUC and the two PU16svia two symmetrical two-wire lines (separately in the upstream and downstream direc-tion) on the rear panel. The external PCI interfaces (section 2.2.2) are established viawire pairs within a cable screen and can span distances of up to 15 m. Data signals withsymmetrical levels from which the frame and clock information is retrieved are transmit-ted via each wire pair.
The PCI frame contains 162 time slots with a width of 10 bits each. The CAS bit is notused in the CMXC and is loaded on fixed potential.
The PCI time slots are designed according to Tab. 2.1.
A useful load of 4 2-Mbit/s links with 32 PCM time slots each is mapped into each PCIframe as shown below:
Bit 1 2 3 4 5 6 7 8 9 10
TS 0 to 160 D1 D2 D3 D4 D5 D6 D7 D8 CAS P
TS 161 R 1 1 1 0 0 1 1 0 P
D1...D8 : PCM data
CAS : Bit for CAS signaling (not used here)
P : Parity bit
R : Reserved bit (in PCI downstream direction: Activity mode of the CUC is displayed)
Tab. 2.1 Structure of a PCI Time Slot
PCI
time slot
PCM
link
PCM
time slot
0 1
01 2
2 3
3 4
Tab. 2.2 PCI Frame Structure
8/12/2019 UMN CMXC c800_1_7619
22/152
22 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
LSI Interface
The LSI interface is established on PU16 (transmitter) and CUC (receiver). It consists of7 symmetrical line pairs and transfers the E1in guide clock from the PU16 to the CUCs.An 8th line pair transfers the frame pulse belonging to the E1 guide clock.Of the two PU16s, only one clock source may be activated per LSI line and the remain-ing transmit drivers are connected with high-impedance. The LSI interfaces are activat-ed via the software according to a clock priority list, see section 2.2.4.
Supervision Bus SVB
Internal communication between units CUC and PU16 takes place via the supervisionbus SVB. This bus is an HDLC interface which works according to the master-slave prin-ciple. The master (primary station) is the active CUC and the slaves (secondary station)the PU16 units.The standby CUC does not access the bus and the line drivers are con-nected inactively.
Supervision bus SVB is used for the following functions: Loading the software and configuration data of units PU16 during intitialization, Distributing the SISA messages via the active CUC to the SISA functional units of
units PU16, Module-internal communication between CUC and PU16
(e.g. control commands of the CUC to unit PU16 for clock source control).
CCUR Interface
There are two unsymmetrical connections between the units to signal the operatingmode of both CUCs and the PCI buses and their redundancy switchover. On PU16, onlyreceivers are connected to the record circuits whereas they are crossed between theCUC receive and transmit lines. A high level on line CCUR indicates that the left CUCis active and is connected via the primary PCI bus. In this mode, the CCURS line is atthe low level. When changing levels, a switchover to the redundant PCI bus and to theredundant central CUC takes place.
4 1
15 26 3
7 4
....
124 1
31125 2
126 3
127 4
128
free...
160
161 FSW
PCI
time slot
PCM
link
PCM
time slot
Tab. 2.2 PCI Frame Structure
8/12/2019 UMN CMXC c800_1_7619
23/152
A50010-A3-C800-1-7619 23
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
CC Interface
The CC interface (cross coupling interface with CC_I and CC_O) connects both CUCsand synchronizes the standby CUC via the clock master. The clock contains the fre-
quency reference and the position of the central multiframe synchronization pulse is im-pressed via a pulse duration modulation.
CCR Interface
The CCR interface connects both CUCs and synchronizes the PCI frame of the standbyCUC via the active CUC.
STSB Interface
Data is transmitted between the active CUC and the standby CUC via the STSB inter-face (status standby control). In this way the two CUCs run quasisynchronously andswitch over procedures can be released very quickly via the static command line(CCUR). The STSB interface is a point-to-point connection between the two centralunits inserted next to one another.
2.2.4 Clock Synchronization
For the CMXC function it is necessary that all the 2-Mbit/s signal streams E1in andE1out are applied with the same clock signal. This requirement is met if the signals atthe output of preceding equipment is derived from the same synchronous clock; other-wise is must be guaranteed by establishing clock loops in all the closed user terminals(transmitting clock = recovered receive clock). On violation of this principle, frame slipsoccur which lead to interferences in signal transmission.
The active CUC is the clock master for all the other CMXC units.
The 2-MHz guide clock can be derived from the following clock sources, see Fig. 2.5: T3in interface to feed an external synchronous clock, Regenerated clock signal which was retrieved from the E1in data of a 2-Mbit/s port Internal oscillator on the CUC (emergency operation).
7 symmetrical wire pairs LSI1 to LSI7 (line synchronization input) have been providedfor the E1in guide clocks from the PU16 units to the CUC. The source for the guide clockcan be selected at random from the 32 E1 ports. The software selects the activatedclock source on the basis of a priority list. This decides which one of the possible receiveclocks of the E1in ports are loaded on which of the 7 guide clock lines.
If PU16, which provides a guide clock, identifies a malfunctioning of the E1in signal, it
disconnects the corresponding clock source. The CUC then identifies clock failure andswitches over to the clock source with the next lower priority (see the alarm table of theCUC in Section 3.3.2). If all the external clock sources fail, the PLL of CUC is switchedto free-running and a prompt alarm is released.
If a clock source with a higher priority becomes available while operating with a lowerpriority standby clock, the guide clock switches over automatically.
8/12/2019 UMN CMXC c800_1_7619
24/152
24 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
Fig. 2.5 CMXC Synchronization
Phase synchronicity requirements of G.703 interface signals can be found in the ITU-T-recommendations G.823 and ETS TBR-12 and they are formed by buffer stores and jit-ter reducers on units PU16. An elastic store sets up the frame synchronicity.
The synchronous clock on units PU16 is derived by means of PLL from the PCI down-stream signal.
For subsequent equipment, the active CUC provides a 2.048-MHz synchronous clockT3out which is synchronous to the current system clock.
Both CUCs manage the T3 interface. The software ensures that only the active CUC ac-cesses the interface.
2.2.5 Conferences
A maximum of 30 digital and 30 analog conference channels can be switched in up to20 mutually independent conferences at the same time. The requirements for analogand digital conferences differ:
For the analog conference, each conference participant receives the total of all the othersignals. Its individual transmit signal is deactivated. The identifications are switched dig-itally for the participants in analog conferences.
For the digital conference, the signals of all the participants are switched with bit-by-bitOR operation. Its individual transmit signal is retained. For the participants in digital con-
ferences, the identifications are also switched digitally as for analog conferences.
....
...
LSI1 LSI7...
E1in/17 to 32...
T3in T3out
E1in/1 to 16 ...
PCIup CUC standbyCUC
PU16PU16
Analog conferences Digital conferences
Maximum number of conference participants 30 30Maximum number of participants per conference 10 30
Maximum number of parallel conferences 10 10
Tab. 2.3 Conference Requirements
8/12/2019 UMN CMXC c800_1_7619
25/152
A50010-A3-C800-1-7619 25
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
2.2.6 Subrate Multiplexer
To switch subrate connections, a subrate channel of 1, 2 or 4 bits is converted to 8 fullbits and then switched and compressed again. Conversion takes place by oversampling
or subsampling.A maximum of 240 bidirectional subbit rate signals each with 8 kbit/s in CMXC can beswitched.
2.2.7 Voice Channel in Common Frequency Radio Networks
In this application a voice channel is transmitted from one source to a number of desti-nations. The group delay time of the voice channel is constant here. There can only beone such connection within the network. This connection is always unidirectional.
The source can only be a VF interface in multiplexer FMX2R3 (with units CUD andUAC68). All subsequent multiplexers/crossconnect multiplexers must synchronize
themselves to the outgoing frames of the multiplexer with the synchronizing clocksource.
2.2.8 Redundancy Concept
2.2.8.1 Module Redundancy
To increase the operating reliability of CMXC, the central CUC is duplicated so that fur-ther functioning of the entire system is guaranteed if the unit fails. Failure of the activeCUC leads to a redundancy switchover if there is another CUC in the CMXC systemmodule. The software releases redundancy switchover. To this end, the operability of all
the components is supervised on both CUCs (active and standby).Units PU16 are not equipped redundantly, i.e. there is no protection switching if a PU16unit fails. Therefore, the CMXC system module has a fault penetration range of 16 E1interfaces.
Fig. 2.6 Redundancy Concept
The PCI buses are duplicated, see Fig. 2.6. A switchover to the redundant bus is pos-sible in case of faults. The central CUCs are connected to separate signal groups (PCISat standby unit).
PCI1 to 8
PCIS1 to 8
STSBCCUR
CCURS
CCUR
CCURS
PU16
CUC
CUCSPU16
CCUR
To external equipment
Redundant CUC
8/12/2019 UMN CMXC c800_1_7619
26/152
26 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
However, the decentralized PU16 units are connected to both the bus systems. Theyreceive information about which one of the two PCI buses is active, the CCUR andCCURS signals (see CCUR Interface).
Bus STSB is used as the communication interface for redundancy operation betweenthe two CUCs (see STSB Interface).
The clock sources for the synchronous clock of CMXC is switched over to standby ac-cording to a priority list (see section 2.2.4).
Both CUCs manage the T3 interface and the QD2 interface. The software ensures thatonly the active CUC accesses the specific interface.
2.2.8.2 Alternative Route Switching for a 2-Mbit/s Connection
One alternative route can be configured for each 2-Mbit/s connection which is switchedover to for the alarm criteria below:
LOS, AIS,Local loop, remote loop always
SYN, BER-3, only for framed signals SYNK, AISK, only for framed signals with CAS signaling BER-5/-6 only for framed signals, if the alarm criterion
was switched on D-Bit, Dk-Bit, N-Bit, Nk-Bit never
The alternative route must be entered into the user menu.
The alarm criterion BER-5/-6 has a lower priority than the LOS, AIS, SYN, BER-3, AISK,SYNK, local loop and remote loop alarms. If a high priority alarm occurs at the one portand a low priory alarm at the other port, the low priority alarm will be used as the trans-
mission route. Therefore, the alarm criterion should be switched on.
2.2.9 Power Supply
Units CUC and PU16 of CMXC are supplied with an input voltage of 48 V (36 V to72 V). The input voltage is fed via a plug in the connector panel of the shelf. For redun-dancy operation, a second plug (S) is provided to feed a further 48 V. The active andstandby CUCs are connected to either of the two voltages in each case. The PU16 unitsare connected to both voltages. The input voltages are fed to the consumers via EMCfilters on the backplane of the shelf.
Fig. 2.7 Power Supply in Shelf SNUS
CUCSCUC
PU16 PU16
Connector panel
48 V/60 V 48 V-S/60 V-S
8/12/2019 UMN CMXC c800_1_7619
27/152
A50010-A3-C800-1-7619 27
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
2.3 Operation and Supervision
2.3.1 Access to CMXC
The CMXC forms an SISA Network Element. The central CUC accesses the NetworkElement via the QD2 slave interface. Addressing the CMXC Network Element is allocat-ed slot-coded via the rear panel of shelf SNUS.
The following types of access are possible, see Fig. 2.8: CMXC connection to the OS via the QD2 slave interface
QD2 access is in stand-alone operation of unit SNUS via the supervision unit SUE.Switch positions connect the internal QD2 bus to the master port of the SUE.
LCT connection via the F interface of the supervision unit.
In stand-alone operation, the DCN channels are connected directly to the QD2 slaveport of SUE via the connector panel of the shelf.
Fig. 2.8 CMXC in Stand-alone Operation Mode (Example)
2.3.2 Operating Elements
The CUC has a jumper to set the impedance of the T3in interface to high-impedance(1.6 k II < 120 pF) or low-impedance (120 symm./75 unsymm.) operation (seeSection 3.3.3).
Jumpers are located on units PU16 to set the impedances of the E1 interfaces. The lineimpedance of each F1 interface can either be set separately to 75 unsymmetrical orto 120symmetrical (see Section 3.4.3).
A 5-step DIL switch is arranged on shelf SNUS to set the SISA address of the systemmodule (see Section 3.2.4).
Detailed information about the switch settings and plug connector allocations can befound in Section 3.
2.3.3 SupervisionSMD-LEDs signal the operating mode for each unit (see Section 3.3.2to 3.4.2).
NEASA32
LCTF
SISA-VLMX/V2
SUE
QD2 slave 1RS485/RS232
V.28
QD2 slave 2
Internal QD2 bus
RS485primary
CMXC
SISA-V
ECC (V.11)FMX2R3
SISA-V
SMX1/4c
SISA-V
LTCOH/LT
SISA-V
LT12CM/LTLT22CM/LTLTO/LT
Internal QD2 bus
T port (QD2 slave 1) for other NEs
QD2-M
8/12/2019 UMN CMXC c800_1_7619
28/152
28 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
The E1, PCI and LSI interfaces are supervised according to alarm tables on the units(see Section 3.3.2to 3.4.2). the CUC supervises PCI and LSI links between the PU16 and the CUC. PU16 evaluates the E1 interfaces.
SISA0 alarms are reported to the OA&M computer. Two LEDs (red and green) on theCUC indicate the system alarms.
2.3.4 Diagnostic Functions
When switching on the input voltages for CMXC, self-test routines of the software andhardware components on the units are first of all performed.
In operation, PCM signals received at the E1 ports can be analyzed continuously ac-cording to ITU-T G.821 and the values stored in quality data records. Both the currentquality counter and any stored record can be displayed.
The number of frame slips occurring at a 2-Mbit/s port can be requested via the craftterminal.
The following loop connections can be established on PU16, see Section 3.4.1: Local loop for fault location within the CMXC system module, Remote loop for fault location of the external 2-Mbit/s connections.
The procedures for alarm evaluation are contained in the Section 5.
2.4 Software
The required SW of network element CMXC is loaded with the craft terminal and SWdownload via the V.24 or the QD2 interface. Special SW in the form of a file exists for
each CMXC unit.
2.4.1 Storage Structure
Each one of the units has a unit computer consisting of a micro controller and variousstorage circuits (FEPROM, EEPROM, RAM) for administering the software and the da-ta. The micro controller controls the internal functional flow on the individual units. Thestorage circuits are used for software and data protection.
In order to retain the configuration in case of a fault, backup versions are stored in theOS which can then be set up again at a later stage.
Firmware containing the initial program loader, self-test programs and type label data
are found on each unit. The firmware is stored in the flash EEPROM on the unit.
The RAM contains the current SW which is loaded from the FEPROM by the initial pro-gram loader.
2.4.2 Initializing
After power-up each unit starts the initial program loader software contained in theFEPROM. The initial program loader comprises the self-test routines of the unit (dura-tion a maximum of 30 s) and log-in into the supervision bus. After successful softwaredownload and starting, the units read-in their configuration data.
For an SW update, the current SW version carries on working in the RAM. A reset mustalways be performed after a new SW has been loaded, so that the unit can reboot.
8/12/2019 UMN CMXC c800_1_7619
29/152
A50010-A3-C800-1-7619 29
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
3 Components
3.1 GeneralThe CMXC consists of a maximum of two CUC units and a maximum of two PU16 unitsin double eurocard size. The units are installed in an SNUS shelf.
The SUE unit used for stand alone operation mode is equipped in SNUS shelf also.
The 19-inch SNUS shelf is used for indoor operation. It can be delivered as stand-aloneor with a complete infrastructure (with power supply, backup battery and signal distrib-utor) as SNU60FTTB or in an SNU180FTTB.
The following system modules can be equipped in SNUS together with CMXC: Multiplexer FMX2R3.1 Line equipment for 2-Mbit/s transmission
on copper cablewith UK2interface according to FTZ 1 TR221 or G.703/short-haul (LT2ME1),HDSL-coded (12 Mbit/s with LTCOH/LT12CM or 2 2 Mbit/s with LT22CM),
on optical cable via single mode glass fibers12 Mbit/s via 2 fibers according to FTZ 1 TR222 (LUOT-A), or22 Mbit/s, transmit and receive direction via 1 fiber (LTO).
Synchronous multiplexer SMX1/4c or the optical line equipment OMX16
All external CMXC interfaces can be accessed via the connector panel of the shelf.Should FMX2R3.1, 2-Mbit/s line equipment and OMX16/SMX1/4c be equipped, the2-Mbit/s interfaces have already been prewired internally and only a section of the inter-faces can be accessed from the outside. Detailed information about internal wiring can
be found in the User Manual FMX2R3.1, UMN, see Section 1.3 "Additional Documenta-tion".
8/12/2019 UMN CMXC c800_1_7619
30/152
30 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
3.2 SNUS Shelf
3.2.1 SNUS Layout
Fig. 3.1 SNUS with Front Panel
101X1V1A1 B1 C1 D1 E1 F1 G1 H1 J1 K1 L1 M1 N1 P1 Q1 R1 S1
E2 F2 G2 H2 J2 K2 L2 M2 N2 P2 Q2 R2 S2 T2D2C2B2
Y2X2U2 W2V2
U3 V3 W3 X3Y3
SMX DSMXTrib.Unit
T3
T3
(+)(-)48V
6A
(+)(-)48V
6A
QD2-Slave
QD2-Master
Tln
Tln
Tln
G.703
Tln
Tln
Tln
G.703 H
DSL(LT3)
PCI
G.703
G.703
G.703
G.703
G.703
1..4
9..12
1..4
9..12
17..21
1..4
9..12
address116
onoff
LC1
FRCON
LC2
LC3
LC4
LC5
LC6
LT2
PBA2
Port Unit 1 CMXC Port Unit 2 Trib Unit SMX
A3
Tln
Tln
Tln
Tln
Tln
Tln
G.703
G.703
5..8
13..16
ECC
PCIS
G.703
G.703
5..8
13..16
G.703
G.703
5..8
13..16
G.703
17..21
V.11
xt.contacts
ZA
LT1
12
12
12
12
12
12
12
12
12
12
F-PC
SIEMENS SNUS
LASER KLASSE 1
LASER CLASS 1
Achtung!
Laser und Glasfasermechanischnicht belasten
ATTENTION!LASER AND GLASS FIBER
MUST NOT BEPHYSICALLY DAMAGED
OR STRAINED
BA DC FE HG KJ ML PN RQ TS VU XW
8/12/2019 UMN CMXC c800_1_7619
31/152
A50010-A3-C800-1-7619 31
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
Fig. 3.2 SNUS Front View with the DIL Switches S101 to S116
Fig. 3.3 DIL Switches S105 to S116
BA DC FE HG KJ ML PN RQ TS VU XW YX1V1A1 B1 C1 D1 E1 F1 G1 H1 J1 K1 L1 M1 N1 P1 Q1 R1 S1
address116
onoff
QD
2-Slave
QD
2-Master
T
ln
T
ln
T
ln
G.703
T
ln
T
ln
T
ln
G.703 H
DS
L(LT3)
PCI
G.703
G.703
G.703
G.703
G.703 (+
)(-)48V
6A
(+
)(-)48V
6A
Y2X2U2
E2 F2 G2 H2 J2 K2 L2 M2 N2 P2 Q2 R2 S2 T2LC1
FRCON
LC2
LC3
LC4
LC5
LC6
LT2
LT1
1..4
9..12
1..4
9..12
17..21
1..4
9..12
W2V2
D2C2B2
PBA2
Port Unit 1 CMXC Port Unit 2 Trib Unit SMX
A3
Tln
Tln
Tln
Tln
Tln
Tln
G.703
G.703
5..8
13..16
ECC
PCIS
G.703
G.703
5..8
13..16
G.703
G.703
5..8
13..16
G.703
17..21
V.11
U3 V3 W3 X3Y3
SMX DSMXTrib.Unit
T3
T3
xt.contacts
ZA
201 202 204 205 206 207 208 209 210 211 212 213 214 215 216 217 SNUS
201202
204 205 206 207 208 209 210 211 212 213214
215216
217
101
S10 3 S1 04
S102
S111 S112 S114 S115
S113 S116
S108
S109
S105
S106
S107
S101
As-delivered condition:For S105to S116all sliders are set tothe downposition.These DIL switches are not used for System
Module CMXC.
ON
S1141 2 3 4
ONS108
ONS109
ON
S1111 2 3 4
ON
S1121 2 3 4
ONS105
ON
S1131 2 3 4
ONS106
ONS107
ON
S1151 2 3 4
ON
S1161 2 3 4
8/12/2019 UMN CMXC c800_1_7619
32/152
32 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
3.2.2 Addressing
Almost all units in the SNUS are assigned addresses via the backplanes. The addressesassigned to the slots are shown in Tab. 3.1.
The SISA addresses of the SUE are set using DIL switch 101 in the terminal panel (pos-sible addresses: 1 to 30), see Fig. 3.6and Fig. 3.4.
Fig. 3.4 DIL Switch S101
The addresses implemented in the SNUS are shown in Tab. 3.1.
Unit In slot QD2 address Slot address (connected and fixed)
SUE 201 Is set using DIL switch
S101 in the terminal panel
of the SNUS, see Fig. 3.6
and Fig. 3.4.
5Bit = 1 to 30
5 bit = 3
(K0...K4 shelf model)
CUD 202 Is set using DIL switch
S102 on the backplane of
the SNUS, see Fig. 3.2.
5Bit; here only 1 to8 usable
SEL_0 = GND
SEL_1 = GND
Line cards 1-6 203 to 208 4 bit = 1 to 6
LT1 as LU1) 3) 207 Fixed (4 bit) = 7
LT1 as LT2) 3) 207 Fixed (5 bit) = 7
LT2 as LU1) 3) 208 Fixed (4 bit) = 8
LT2 as LT2) 3) 208 Fixed (5 bit) = 8
LT3 as LU1) 209 Fixed (4 bit) = 9
LT3 as LT2) 209 Fixed (5 bit) = 9
PU16(1) 210 5 bit = 10
CUC(1) 211 Fixed (5 bit) = 13 5 bit = 11
CUC(2) 212 Fixed (5 bit) = 13 5 bit = 12PU16(2) 213 5 bit = 13
ADM (SMX) 216 Fixed (5 bit) = 16
Trib.Unit 214
LU1)= LUOT, LUCP, LUC, LUCT
LT2)= LTO, LTCOH, LT12CM, LT22CM, LT2ME1
3) If an LT/LU unit instead of a line card is equipped in slots 207 or 208, the slot must be configured accord-
ingly (with DIL switches S106 and S107 for slot 207 or with DIL switch S109 for slot 208). Switches S105
and S108 must always be switched, see Fig. 3.2, Fig. 3.3
Tab. 3.1 SNUS Overview of Addressing and the Units
1
ON = LOW = log 0Example:Switch 1 on OFF corresponds to 24= 16Switch 5 on OFF corresponds to 20= 1Corresponds to address 17 for the SUE
ON (0)
OFF (1)
24 23 22 21 20
5
8/12/2019 UMN CMXC c800_1_7619
33/152
A50010-A3-C800-1-7619 33
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
3.2.3 QD2 Structure
If the stand alone operation mode the SUE must be used for supervision. Operating ormaintenance functions can be carried out locally via an F interface using a local craftterminal. The SUE monitors all units in the SNUS. The internal QD2 bus of the SNUSmust be switched using switches S103 (all slider units on OFF) and S104 (all sliderunits on ON) to the SUE master port, see Fig. 3.2and Fig. 3.5.
Slave port 1 of the SUE is executed as a T interface, likewise the T connections are ac-cessible in the X101 slave connector, see Fig. 3.6.
Master port 1 of the SUE is stored in the QD2 X102 master connector and is the startingpoint of the internal QD2 bus when used in standalone mode. Further slaves in the in-ternal QD2 bus can be connected to X102.
Slave port 2 of the SUE is also located in the QD2 X102 master connector. The over-head interface of LT location 3 is also located here. Connection to slave 2 via an appro-priately assigned connector is possible and thus a control channel via the overhead froma remote device (unit in LT location 3 as a feeder for the SNUS).
Further control is possible via ECC channels. The ECC connections of both CUC loca-tions are stored in parallel and in a 25-pin D-sub connector. Of the four ECC interfacesof the CMXC, two are equipped with clock transmission. The ECC of the CUD is also
routed to this X131 D-sub.
Fig. 3.5 DIL Switches S103 and S104
PSD 218 5 bit = 18
optional with
OMX16
DSMX34 215 5 bit = 15
OTRU36 217 5 bit = 17
OTSU_2M 218 Fixed (5 bit) = 18
Unit In slot QD2 address Slot address (connected and fixed)
LU1)= LUOT, LUCP, LUC, LUCT
LT2)= LTO, LTCOH, LT12CM, LT22CM, LT2ME1
3) If an LT/LU unit instead of a line card is equipped in slots 207 or 208, the slot must be configured accord-
ingly (with DIL switches S106 and S107 for slot 207 or with DIL switch S109 for slot 208). Switches S105
and S108 must always be switched, see Fig. 3.2, Fig. 3.3
Tab. 3.1 SNUS Overview of Addressing and the Units (Cont.)
ON
S104
4321
ON
S103
4321
As-delivered condition:For S103 all slider units are set to OFF (down position) and forS104 all slider units are set to ON (up position), i.e. the SNUS ismonitored by a SUE(standalone, without COMPS and without OSU)
8/12/2019 UMN CMXC c800_1_7619
34/152
34 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
3.2.4 Position and Assignment of Connectors
Fig. 3.6 Location of Connectors and Equipping of Units
In the following topics, assignments of connectors in Terminal Panel used for the CMXCunits are only described.
48V
48V
QD2-S
Alarm
PB
-+
-+
A
X101 to X154 are the connectors in the terminal panel
X201 to X316 are the connectors for the units in the shelf
1) DIL switch S101 for setting the SISA address of the SUE
2) LT1/2/3 = LT/LU units (LT22CM may only be inserted into slot 209)
C
QD2-M
B D E F G H
I/O1-4
J
I/O9-12
K
HDSL-LT3
L
PCI
M
I/O1-4
N
I/O9-12
P
I/O1-4
Q
I/O9-12
R
I/O1
7-21
S
I/O5-8
I/O1
3-16
ECC-CUC
PCIS
I/O5-8
I/O1
3-16
I/O5-8
I/O1
3-16
I/O1
7-21
ZA
T3an
T
3out
V.11
Add.1)
E3IN
X153
X151
E3OUT
X154
X152
X301
201
X201
SUE
X302
202
X202
CUD
/CUA
X303
203
X203
LC1/FRCO
N
X304
204
X204
LC2
X305
205
X205
LC3
X306
206
X206
LC4
X307
207
X207
LC5/LT12)
X308
208
X208
LC6/LT22)
X309
209
X209
LT32)
X310
210
X210
PU16
X311
211
X211
CUC
X312
212
X212
CUC
X313
213
X213
PU16
X14D
X14C
214
X14BX14A
TU
X314
215
X214
DSMX34
X15D
X15C
216
X15BX15A
ADM
X316
218
X216
OTSU_
2M/
PSD
X315
217
X215
OTRU36
or
or
X121X122
X123 X125 X127 X129 X131 X133 X135 X137
X124 X126 X128 X130 X132 X134 X136
X138
Exchangeconn.
LCslots 2Mbit/s 2Mbit/s2Mbit/s
X120
X104 X106 X108 X110 X112 X114 X116
X103 X105 X107 X109 X111 X113 X115 X117 X141 X142X101
X102
X143
X144
Slot desig-
nations
S101
T
8/12/2019 UMN CMXC c800_1_7619
35/152
A50010-A3-C800-1-7619 35
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
Connectors of the Power Supply (X141 and X142)
QD2 (X101 and X102) and Alarm Inputs (X121)
Notes to Tab. 3.3:GND = operation ground
GND_S = shielded ground
For X101:
Slave1 from SUE
QD2S1 In a/b
QD2S1 OUT a/b
T-connections to Slave1 of the SUE
QD2T IN a/b
QD2T OUT a/b
X141 Pin X142 Pin
1 1
-48V (MUP1) 2 -48V (MUP2) 2
+48V (GND) 3 +48V (GND) 3
Tab. 3.2 Assignment of Connectors X141 (left and ) X142 (right)
Pin X101
QD2-Slave
X102
QD2-Master
X121
Alarm inputs
1 GND_S GND_S GND_S
2 QD2S1 OUT a QD2M IN a AIN1
3 QD2T1 OUT a AIN3
4 QD2S1 IN a QD2M OUT a AIN5
5 QD2T1 IN a AIN7
6
7 DAT
8 GND GND GND
9 QD2S1 OUT b QD2M IN b AIN2
10 QD2T1 OUT b AIN4
11 QD2S1 IN b QD2M OUT b AIN6
12 QD2T1 IN b AIN8
13
14 NRST
15 CLK
Tab. 3.3 Terminal Assignment of Jacks X101, X102 and X121
8/12/2019 UMN CMXC c800_1_7619
36/152
36 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
DAT, CLK, NRST = not used in CMXC
For X121:AIN1 to AIn8 = alarm inputs of the SUE
AM = negative operating voltage for alarm contacts
For X102:Master from SUE:
QD2M IN a/bQDM OUT a/b
T3 Interface (X143 and X144)
Notes to Tab. 3.11:GND = operation ground
GND_S = shielded ground
For X143:T3 OUT1 a/b = T3-output from CUC plug-in places
T3 OUT2 a/b = T3-output from CUD plug-in place (202)
For X144:T3 IN1 a/b = T3in1-input to CUD-, LT-/LU-, and CUC plug-in places
T3 OUT1 a/b = T3in1-output to the Terminal Panel
T3 IN2 a/b = T3in2-input to the ADM plug-in place
T3 OUT2 a/b = T3in2-output to the Terminal Panel
Pin X143
Connector T3ab
X144
Connector
T3an
1 GND_S GND_S
2 T3 OUT1 a T3 IN1 a
3 T3 OUT1 a
4 T3 OUT2 a T3 IN2 a
5 T3 OUT2 a
6 T3 OUT1 b T3 IN1 b
7 T3 OUT1 b
8 T3 OUT2 b T3 IN2 b
9 T3 OUT2 b
Tab. 3.4 Terminal Assignment of 9-Contact Jacks X143 and X144
8/12/2019 UMN CMXC c800_1_7619
37/152
A50010-A3-C800-1-7619 37
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
ZA Contacts (X122) and ECC of the CUC (X131)
Notes to Tab. 3.11:GND = operation ground
GND_S = shielded ground
For X122:
Index 1 = SUE
Index 2 = CU plug-in place (202), not used in CMXC
Index 3...5 = LT plug-in places (207 to 209), not used in CMXC
Index 6, 7 = CUC, plug-in places 211 and 212
Index 8 = PSD plug-in place 218, not used in CMXC
Pin X122
ZA-contacts
X131
ECC of the CUC
(in addition to CUD)
1 GND_S GND_S
2 EAN_A1
3 ZAA2 EAB_A1
4 ZAA3 ET_A1
5 ZAA4 EAN_A2
6 ZAA5 EAB_A2
7 ZAA6 ET_A2
8 ZAA7 EAN_A3
9 ZAA8 EAB_A3
10 ZAA9 EAN_A4
11 EAB_A4
12 EANCUD_A
13 GND EABCUD_A
14 ZAB1 EAN_B1
15 ZAB2 EAB_B1
16 ZAB3 ET_B1
17 ZAB4 EAN_B2
18 ZAB5 EAB_B219 ZAB6 ET_B2
20 ZAB7 EAN_B3
21 ZAB8 EAB_B3
22 ZAB9 EAN_B4
23 EAB_B4
24 EANCUD_B
25 GND EABCUD_B
Tab. 3.5 Terminal Assignment of Jacks X122 and X131
8/12/2019 UMN CMXC c800_1_7619
38/152
38 A50010-A3-C800-1-7619
UMN CMXC User ManualCrossconnect Multiplexer CMXC
Index 9 = OTSU2M, plug-in place 218, not used in CMXC
(optional equipping)
For X131:ECC1 to ECC4 of the CUC from both units (connect in parallel)
ECC1 and ECC2 with clock
ECC3 and ECC4 without clock
Interfaces 2 Mbit/s G.703 (X109 to X110, X129 to X130, X113 to X117 and X133 to
X137)
Interfaces 2 Mbit/s G.703
Pin X109/X113 X129/X133 X110/X114 X130/X134
1 GND_S GND_S GND_S GND_S
2 E1 OUT1 a E1 OUT5 a E1 OUT9 a E1 OUT13 a
3 E1 IN1 a E1 IN5 a E1 IN9 a E1 IN13 a
4 E1 OUT2 a E1 OUT6 a E1 OUT10 a E1 OUT14 a
5 E1 IN2 a E1 IN6 a E1 IN10 a E1 IN14 a
6 E1 OUT3 a E1 OUT7 a E1 OUT11 a E1 OUT15 a
7 E1 IN3 a E1 IN7 a E1 IN11 a E1 IN15 a
8 E1 OUT4 a E1 OUT8 a E1 OUT12 a E1 OUT16 a
9 E1 IN4 a E1 IN8 a E1 IN12 a E1 IN16 a
10
11
12
13
14 E1 OUT1 b E1 OUT5 b E1 OUT9 b E1 OUT13 b
15 E1 IN1 b E1 IN5 b E1 IN9 b E1 IN13 b
16 E1 OUT2 b E1 OUT6 b E1 OUT10 b E1 OUT14 b
17 E1 IN2 b E1 IN6 b E1 IN10 b E1 IN14 b
18 E1 OUT3 b E1 OUT7 b E1 OUT11 b E1 OUT15 b
19 E1 IN3 b E1 IN7 b E1 IN11 b E1 IN15 b
20 E1 OUT4 b E1 OUT8 b E1 OUT12 b E1 OUT16 b
21 E1 IN4 b E1 IN8 b E1 IN12 b E1 IN16 b
22
23
24
25
Tab. 3.6 Terminal Assignment of Jacks X109, X110, X 113, X114, X129, X130,X133, X134 and X115
8/12/2019 UMN CMXC c800_1_7619
39/152
A50010-A3-C800-1-7619 39
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
Notes to Tab. 3.6:GND_S = shielded ground
For X109, X129, X110 and X130:
E1 OUTy a = a-wire,E1 OUTy b = b-wire from output 2Mbit/s G.703 from Port y (PU16/1)E1 INy a = a-wire,E1 INy b = b-wire from input 2Mbit/s G.703 from Port y (PU16/1)E1 = 2Mbit/s G.703Example:E1 OUT1 a = a-wire,E1 OUT1 b = b-wire from output 2Mbit/s G.703 from Port 1 (PU16/1)E1 IN1 a = a-wire,E1 IN1 b = b-wire from input 2Mbit/s G.703 from Port 1 (PU16/1)E1 = 2Mbit/s G.703
The external names E1 IN.. E1 OUT.. are relate to the PU16.
The internal Interfaces from X109 are port 1 to 4 of the PU16/1 in Slot 210.The Interfaces from X129 are port 5 to 8 of the PU16/1 in Slot 210 and are internal con-nected to the first interface of the CUD place and of the 3 LT plug-in places.The interfaces from X110 come from the ADM and are internal connected with port 9 to12 of the PU16/1 in Slot 210.The interfaces from X130 come from the ADM and are internal connected with port 13to 16 of the PU16/1 in Slot 210.
For X113, X133, X114 and X134:
E1 OUTy a = a-wire,E1 OUTy b = b-wire from output 2Mbit/s G.703 from Port y (PU16/2)E1 INy a = a-wire,E1 INy b = b-wire from input 2Mbit/s G.703 from Port y (PU16/2)E1 = 2Mbit/s G.703Example:E1 OUT1 a = a-wire,E1 OUT1 b = b-wire from output 2Mbit/s G.703 from Port 1 (PU16/2)E1 IN1 a = a-wire,E1 IN1 b = b-wire from input 2Mbit/s G.703 from Port 1 (PU16/2)E1 = 2Mbit/s G.703
The external names E1 IN.. E1 OUT.. are relate to the PU16.
The interfaces from X113 are Port 1 to 4 of the PU16/2 in Slot 213.The interfaces from X133 are Port 5 to 8 of the PU16/2 in Slot 213 and are internal con-nected to the second interface of the CUD place and of the 3 LT plug-in places.The interfaces from X114 come from the ADM and are internal connected with port 9 to12 of the PU16/2 in Slot 213.The interfaces from X134 come from the ADM and are internal connected with port 13to 16 of the PU16/2 in Slot 213.
8/12/2019 UMN CMXC c800_1_7619
40/152
8/12/2019 UMN CMXC c800_1_7619
41/152
A50010-A3-C800-1-7619 41
User ManualCrossconnect Multiplexer CMXC
UMN CMXC
Fig. 3.7 CUC Block Diagram
The CUC allows conference calls for analog and digital signals as well as correspondingidentification processing (CAS conference). The total number of subscribers for confer-ence operation is 30. These can be a maximum of 10 analog and/or 10 digital confer-ences with 3 subscribers each and a maximum of 10 analog or 30 digital subscribers foreach conference.
The CUC performs the following functions: Crossconnecting the 64-kbit/s signals in the switching matrix and administering the
database needed for this Switching analog, digital and CAS conferences and administering associated data Clock generation by selecting the guide clock
Exchanging configuration and program information between CUC and PU16 via su-pervision bus SVB Data exchange between the CUC and PU16 units via PCI links Standby control Alarm signaling via ZA(A) and ZA(B) contacts and LEDs Providing the time.
The CUC has the following interfaces: Data
8 x PCIs as system-internal interfaces to transmit PCM signals between the CUCand the peripheral units PU16
4 x PCI interfaces for connecting external equipment
Clock pulses 7 x LSI interfaces to receive the 2-MHz guide clock from PU16
LSI1 to LSI7
Frame clock
System clock
SVB
STSB
T3in
CC, CCR (unsym.)
PUP
MUP
SISA-ADR (0 to 4)
CCUR (unsym.)
5