VJ Coupling Data

VJ102CI/SfB May 1999

It6

DIMENSIONAL DATA

IMPORTANT NOTICE The technical, performance data, specifications, dimensions and all other information published in the Design Data section supersede all previously published information. All data contained herein is subject to change without notice. The information given in the following pages is intended as a general guide to the proper design and installation of practical piping systems using Viking Johnson products, and is not intended as a substitute for competent, professional advice, which should always be sought in the design of any piping system. Good piping practice should always prevail and recommended design pressures, temperatures, tolerances and loads should never be exceeded. Special conditions often exist for which the information given here is not specifically suited and specialist engineering advice should be obtained. As with any other piping system, the specific advantages and limitations of Viking Johnson products should be considered when designing a system using Viking Johnson products. The suggestions made here do not set out to give specific solutions to actual installation problems but to give ideas on which to base your own unique solutions. While every effort has been made to ensure its accuracy, Viking Johnson make no express or implied warranty of any kind in respect of the information contained in this brochure or the materials referred to herein. Any person making use of the information contained here does so entirely at their own risk and assumes any and all liability resulting from such use. The information contained within this section applies specifically to Viking Johnson products only, and is not intended to apply to any other bolted sleeve type coupling product. 1999 by Viking Johnson. Printed in the United Kingdom. No part of this booklet may be reproduced, stored or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without prior permission of Viking Johnson. Viking Johnson 1999 Tel: +44 (0)1462 443322 Fax: +44 (0)1462 443311 e-mail: [email protected]

ContentsCouplings ..................................................................................................5MaxiFit........................................................................................6 AquaGrip ....................................................................................7 FlexLock .....................................................................................7 QuickFit...................................................................................8-9 Large Diameter .....................................................................9-13 Juno..........................................................................................13

Viking Johnson

Stepped Couplings..............................................................................14MaxiStep ..................................................................................15 AquaGrip ..................................................................................16 Large Diameter ...................................................................16-17 Juno..........................................................................................18

Flange Adaptors ...................................................................................19MaxiDaptor .........................................................................20-21 AquaGrip.............................................................................21-23 FlexLock ...................................................................................23 QuickFit...............................................................................24-25 Large Diameter ...................................................................25-33

Repair and Tapping Products .........................................................34EasiClamp & EasiTap...............................................................35 Large Diameter EasiClamp & EasiTap ....................................35 Universal EasiTee.....................................................................36 HandiClamp .............................................................................37 Large Diameter Under Pressure Tees.....................................38 EasiCollar .................................................................................38

Other ProductsDismantling Joints..............................................................39-41 LinerGrip...................................................................................42 Juno Adaptors .........................................................................42

Supplementary InformationWorking Pressure Table...........................................................43 Corrosion Protection ...............................................................44 Summary of Gaskets ...............................................................45 Chemical Resistance Chart.....................................................46 Flange Comparison Chart .......................................................47 O.D. Conversion Chart .......................................................48-49

Viking Johnson 1999

Tel: +44 (0)1462 443322 Fax: +44 (0)1462 443311 e-mail: [email protected]

GPS

IntroductionThe Viking Johnson System for joining plain-ended pipes was first introduced to the market in 1931 and is now recognised as being second to none in reliability and quality. This brochure provides full dimensions and material specifications for the various Viking Johnson products. Should you require any additional information, please contact the Marketing Department. The Viking Johnson system is suitable for an enormous range of pipework applications and it is therefore impossible to give a comprehensive list of potential uses. In general terms, the system is suitable for virtually any pipeline, above or below ground level, working within the following typical parameters: Working Pressure - up to 100 bar (1450psi), according to size. Temperature - limited by gasket grade used, but within the range - 60C to 200C. (-75F to 390F) Suitable for - water, gas, oil, petrochemicals, sewage, powdered solids, granular solids, air. Location - above or below ground. Backed by many years of design and manufacturing experience, Viking Johnson are confident that the Viking Johnson System is a complete and cost effective answer to almost all pipeline installation problems. Compare the following benefits with those offered by alternative pipe jointing systems: ISO 9001 certification is proof of our exacting quality standards. Exclusive Viking Johnson gaskets, moulded in our own plant to exacting specifications, assure perfect lifetime sealing, meeting all relevant Standards. Size range extends from 15mm (0.5") to more than 5000mm (200"). The Viking Johnson System is designed for plain-ended pipes eliminating threading, bevelling, welding or flanging. The system can joint most types of pipes, valves or meters. By specifying Viking Johnson, installation delays caused by adverse weather conditions are overcome, particularly relevant to PE installation. You can rely on Viking Johnson products. Their dependability has

Viking Johnson

been demonstrated for over 60 years, in all conditions of service. On-site jointing equipment, with Viking Johnson all you need is a spanner and torque wrench. The simplicity of our design assures you of couplings which will assemble quickly, easily and accurately every time. Company representatives are available to offer technical advice to the installer. As a mechanical jointing system it can eliminate the need for specialist labour or on-site fabrication. Viking Johnson couplings are protected for life against corrosion with a range of specialised coatings. Please state coating required when ordering. Viking Johnson has over 80 agents and Distributors worldwide, in addition to an exclusive Distributor network throughout the UK. Unless otherwise stated, all dimensions are in mm. The working pressure quoted in Bar is that of the coupling/flange adaptor etc. and not that of the pipe. Working pressure is generally 2/3rds of the test pressure.

G l o s s a r y o f Te r m sThe following abbreviations are used in this brochure:OD NB DN PN CI - Pipe outside diameter. - Nominal bore. - Nominal diameter, in millimetres. - Nominal pressure, in bar (1 bar = 0.1 MPa = 0.1 N/mm2 14.5 lbf/in2). - Grey cast iron. - Ductile iron. - Polyethylene. - High performance polyethylene (PE100)Tel: +44 (0)1462 443322 Fax: +44 (0)1462 443311 e-mail: [email protected]

AC GRP uPVC

- Asbestos cement. - Glass reinforced plastics. - Unplasticised polyvinyl chloride.

PVC-u - Metric uPVC pipe (including molecular oriented and impact modified). ABS NBR WBS PCD - Acrylonitrile butadiene styrene. - Nitrile butadiene rubber. - UK Water Research Centre, Water Byelaws Scheme Approval. - Pitch circle diameter. EPDM - Ethylene propylene diene monomer.

4

DI PE HPPE

MDPE - Medium density polyethylene (PE80)

Viking Johnson 1999

GPS

Couplings

Viking Johnson

MaxiFit Coupling

AquaGrip Coupling

FlexLock Coupling

Standard Coupling

BOLT TORQUE TABLE FOR COUPLINGSPRODUCT COATING BOLT SIZE M12 M16 ALL PRODUCTS EXCEPT AQUAGRIP BLACK RILSAN TORQUE lbf.ft Nm 40 - 50 55 - 65 70 - 80 95 - 110 AQUAGRIP BLACK RILSAN TORQUE lbf.ft Nm 55-60 70-75 BLUE SHERAPLEX TORQUE lbf.ft Nm 40-50 55-65 -

GPS

FULL BOLT TORQUE MUST BE ACHIEVED TO ENSURE THAT COUPLING / FLANGE ADAPTOR etc. FUNCTIONS TO ITS DESIGNED PERFORMANCE STANDARDS. Viking Johnson 1999 Tel: +44 (0)1462 443322 Fax: +44 (0)1462 443311 e-mail: [email protected]

5

MaxiFit CouplingsTolerance Min Max47.9 59.5 72.2 88.1 107.2 109.6 118.0 132.2 138.9 141.9 158.2 159.2 192.9 218.1 230.0 250.0 272.0 322.9 332.0 351.0 374.5 386.0 394.3 404.8 412.0 418.2 425.0 434.5 439.0 455.0 476.0 487.0 492.0 501.9 515.0 527.0 540.1 546.0 555.3 565.0 593.0 601.0 613.0 618.0 630.0 654.0 662.0 678.0 59.5 72.0 85.0 102.4 115.1 127.8 131.5 146.0 153.2 156.2 169.9 181.6 209.0 235.0 247.0 267.0 289.0 339.4 349.0 368.0 391.5 403.0 411.3 421.8 429.0 435.2 442.0 451.5 456.0 472.0 493.0 504.3 509.0 518.9 532.0 544.0 557.1 563.0 572.3 582.0 610.0 618.0 630.0 635.0 647.0 671.0 679.0 695.0

Viking JohnsonBolts No. - Dia x Length2 - M12 x 175 3 - M12 x 175 3 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 195 4 - M12 x 215 4 - M12 x 215 5 - M12 x 215 6 - M12 x 215 6 - M12 x 215 8 - M12 x 215 8 - M12 x 215 8 - M12 x 340 8 - M12 x 340 8 - M12 x 340 8 - M12 x 340 8 - M12 x 340 10 - M12 x 340 8 - M12 x 340 8 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 12 - M12 x 340 12 - M12 x 340 10 - M12 x 340 12 - M12 x 340 12 - M12 x 340 12 - M12 x 340 12 - M12 x 340 12 - M12 x 340 12 - M12 x 340 12 - M12 x 340 14 - M12 x 340 14 - M12 x 340 14 - M12 x 340 14 - M12 x 340

Gasket1637 1613 1614 1615 1620 1759 1616 1635 1633 1633 1621 1760 1758 1757 1756 1655 1656 1657 1658 6002 1659 6035 1766 1767 6023 1784 1662 1768 6036 6003 1770 1771 6037 1772 6024 1773 1774 6038 1775 1776 6021 6020 6019 6025 1778 6039 1780 6005

A149.5 164.0 177.0 197.5 224.5 211.5 226.0 248.5 248.5 248.5 279.0 274.0 321.0 306.5 357.0 379.0 400.5 451.5 461.0 478.0 501.5 513.0 521.5 532.0 539.0 545.0 552.0 561.5 566.0 582.0 603.0 614.5 619.0 629.0 642.0 654.0 667.0 673.0 682.5 692.0 720.0 728.0 740.0 745.0 757.0 781.0 789.0 802.0

Dimensions B140 140 140 140 140 140 140 140 140 140 140 165 185 185 185 185 185 185 185 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310 310

C178 178 178 178 178 178 178 178 178 178 178 203 223 223 223 223 223 223 223 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348

Setting Gap (x)20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 25 25 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40

Weight (Kg)3.1 2.6 2.9 3.7 4.6 4.1 4.3 5.3 4.8 5.6 6.6 6.2 8.5 9.2 15.6 16.3 17.5 20.1 20.6 32.4 34.2 35.2 35.6 36.4 37.6 37.6 38.2 39.6 40.2 41.2 43.0 43.9 44.3 44.5 46.7 47.7 47.8 48.5 49.8 51.2 52.4 52.9 53.8 54.6 56.1 57.9 58.4 59.0

MaxiFitXtra CouplingsMin109.6 159.2 218.1

Tolerance Max127.8 181.6 235.0

Gasket1759 1760 1757

Bolts No. - Dia x Length4 - M12 x 275 4 - M12 x 275 4 - M12 x 275

A215.5 274.0 320.5

Dimensions B245 245 245

C283 283 283

Setting Gap (x)20 20 20

Weight (Kg)5.3 7.5 11.6

6

Viking Johnson can manufacture Coupling products to virtually any diameter. Those shown are for information. For sizes or diameters not shown, please request further information.

Viking Johnson 1999


GPS

AquaGrip CouplingsPipe O.D. (mm)63 90 90 110 110 125 125 160 160 160 180 180

Viking JohnsonSegments Bolts Half No. - Dia x Length2 2 - M12 x 195 4 - M12 x 195 4 - M12 x 195 4 - M12 x 195 4 - M12 x 195 6 - M12 x 195 6 - M12 x 195 8 - M12 x 215 8 - M12 x 215 8 - M12 x 215 8 - M12 x 215 8 - M12 x 215

SDR Rating11 11 17/17.6 11 17/17.6 11 17/17.6 11 17/17.6 26 11 17/17.6

Gasket6001 1785 1785 1786 1786 1787 1787 1788 1788 1788 1789 1789

No. of Gripper Full20 28 28 34 34 38 38 48 48 48 52 52

A144.0 167.5 167.5 188.0 188.0 203.0 203.0 240.0 240.0 240.0 257.5 257.5

Dimensions B C180.0 180.0 180.0 180.0 180.0 180.0 180.0 200.0 200.0 200.0 200.0 200.0 203 203 203 203 203 203 203 223 223 223 223 223

Setting Gap (x) Min Max20 20 20 20 20 20 20 20 20 20 20 20 40 40 40 40 40 40 40 40 40 40 40 40

Weight (kg)2.4 3.7 3.8 5.3 5.4 5.7 5.8 8.8 9.0 9.8 9.5 9.8

FlexLock Couplings for Steel PipePipe NominalDN50/2" DN65/2.5" DN80/3" DN100/4" DN150/6" DN150/6" DN200/8" DN250/10"

Pipe O.D.60.3 76.1 88.9 114.3 165.1 168.3 219.1 273.0

Gasket1375 1394 1382 1367 1369 1369 1370 1737

Bolts No.- Dia x Length2 - M12 x 145 2 - M12 x 160 4 - M12 x 160 4 - M12 x 175 6 - M12 x 175 6 - M12 x 175 8 - M12 x 175 12 - M16 x 275

No. of Inserts3 3 4 4 7 7 12 15

A

Dimensions B C127 140 140 153 153 153 153 256 157 170 170 183 183 183 183 286

Setting Gap (x) Min Max20 20 20 20 20 20 20 20 40 40 40 40 40 40 40 40

Weight (kg)2.7 3.2 4.2 6.1 9.2 9.2 11.9 32.1

Pressure (bar) Working Test16 16 16 16 16 16 16 10 24 24 24 24 24 24 24 15

135.0 151.5 163.0 194.5 253.5 255.5 309.5 376.0

F l e x L o c k C o u p l i n g s f o r M e t r i c D u c t i l e I ro n P i p ePipe NominalDN80/3" DN100/4" DN150/6" DN200/8" DN250/10"

Pipe O.D.98.0 118.0 170.0 222.0 274.0

Gasket1630 1618 1369 1631 1737

Bolts No. - Dia x Length4 - M12 x 195 4 - M12 x 195 6 - M12 x 175 6 - M16 x 195 12 - M16 x 275

No. of Inserts4 4 7 12 15

A

Dimensions B C173 173 148 176 256 203 203 178 206 286

Setting Gap (x) Min Max20 20 20 20 20 40 40 40 40 40

Weight (kg)5.21 5.61 9.24 11.90 32.15

Pressure (bar) Working Test16 16 16 16 10 24 24 24 24 15

181.0 200.0 255.5 316.0 376.0

GPS

7Viking Johnson can manufacture Coupling products to virtually any diameter. Those shown are for information. For sizes or diameters not shown, please request further information.

Viking Johnson 1999


QuickFit Couplings for pipes up to and including DN300/12"Pipe NominalDN32/1.25" DN32/1.25" DN40/1.5" DN40/1.5" DN40/1.5" DN50/2" DN63 DN50/2" DN50/2" DN50/2" DN65/2.5" DN65/2.5" DN65/2.5" DN75 DN65/2.5" DN80/3" DN80/3" DN80/3" DN80/3" DN80/3" DN90/3.5" DN100/4" DN110 DN100/4" DN100/4" DN100/4 DN100/4" DN125 DN125/5" DN125/5" DN125/5" DN125/5" DN125/5" DN 150/6" DN 150/6" DN 150/6" DN 150/6" DN 150/6" DN 150/6" DN 150/6" DN 150/6" DN180 DN175/7" DN200 DN200/8" DN200/8" DN200/8" DN225 DN200/8" DN200/8"

Viking Johnson

Pipe TypeSteel/IPS/Imp PVC ISO 4200/3 Steel Steel/IPS/Imp PVC 1.5" AC ISO 4200/2 Steel Steel/IPS/Imp PVC Metric PVC AWWA cl A CI Cl 25 AC Cast Iron ISO 4200/2 Steel ISO 4200/3 Steel API 5L Metric PVC Steel/IPS/Imp PVC Steel/IPS/Imp PVC Metric PVC Cast Iron Metric Ductile Iron/AC AWWA CI Cl BCD Steel ISO 4200/3 Steel Metric PVC Steel/IPS/Imp PVC Metric Ductile Iron Cast Iron AWWA DI/PVC Metric PVC ISO 4200/2 Steel Steel/Imp PVC Metric PVC Imp PVC Steel/Imp PVC ISO 4200/3 Steel Metric PVC BS 1387 Steel Steel/IPS/Imp PVC Metric Ductile Iron AWWA DI/PVC BS CI ISO Steel Metric PVC Steel/Imp PVC Metric PVC Steel/IPS/Imp PVC GRP* Metric Ductile Iron Metric PVC AWWA DI/PVC BS CI Steel/Imp PVC Metric PVC BS CI

Pipe O.D.38.0 44.5 48.3 57.0 57.0 60.3 63.0 63.5 69.0 69.1 70.0 73.0 73.0 75.0 76.1 88.9 90.0 96.0 98.0 100.5 101.6 108.0 110.0 114.3 118.0 122.0 122.0 125.0 133.0 139.7 140.0 140.2 141.3 159.0 160.0 165.1 168.3 170.0 175.3 177.3 177.8 180.0 193.7 200.0 219.1 220.0 222.0 225.0 230.0 232.0 244.5 250.0 259.0

Tolerance Gasket Bolts Locating Dimensions (for QuickFit Unfitted No. - Dia x Length Plugs A B C distance L) No. off+0.8,-0.4 (100) +0.8,-0.4 (100) +0.8,-0.4 (100) 2.0 (100) +0.8,-0.4 (100) 0.8 (100) +0.3,-0.0 (100) 1.25 (100) 0.6 (100) 2.0 (100) 0.8 (100) 0.8 (100) 0.8 (100) +0.3,-0.0 (100) 0.8 (100) 0.8 (100) +0.3,-0.0 (100) 2.0 (100) 2.2 (100) 1.5 (100) 0.8 (100) 0.8 (100) +0.4,-0.0 (100) 0.8 (100) 2.2 (100) 2.0 (100) 1.5 (100) +0.4,-0.0 (100) +1.6,-0.8 (100) +1.6,-0.8 (100) +0.5,-0.0 (100) +1.6,-0.8 (100) +1.6,-0.8 (100) +1.6,-0.8 (100) +0.5,-0.0 (100) +1.6,-0.8 (100) +1.6,-0.8 (100) 2.4 (100) 1.5 (100) 2.0 (100) +1.6,-0.8 (100) +0.6,-0.0 (100) +1.6,-0.8 (100) +0.6,-0.0 (100) +1.6,-0.8 (100) 2.4 (100) 2.4 (100) +0.7,-0.0 (100) 1.5 (100) 2.0 (100) +1.6,-0.8 (100) +0.8,-0.0 (100) 2.0 (100) 1572 1573 1574 1599 1599 1500 1582 1582 1565 1565 1565 804 804 804 1560 1501 1501 1594 1537 1537 1564 1596 1561 1593 1569 1580 1580 1580 1563 1598 1598 1598 1503 1559 1559 1585 1505 1505 A1409 A1506 A1506 A1506 1507 736* A1597 1510 1510 A1401 A1410 A1550 A1542 A1402 A1551 599 523 523 650 650 650 590 638 590 638 638 549 549 549 964 550 550 550 964 737 737 737 525 525 616 616 616 551 609 736 743 526 526 753 753 602/753 579/602 579 652 967 779 589 710 710 547 547 547 657 657 657 2 - M12 x 145 2 - M12 x 145 2 - M12 x 145 2 - M12 x 145 2 - M12 x 145 2 - M12 x 145 2 - M12 x 175 2 - M12 x 175 2 - M12 x 175 2 - M12 x 175 2 - M12 x 175 2 - M12 x 175 2 - M12 x 175 2 - M12 x 175 2 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 5 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 6 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 110.0 126.0 126.0 138.0 138.0 138.0 138.0 138.0 150.0 150.0 150.0 150.0 150.0 150.0 150.0 161.0 161.0 177.0 177.0 177.0 177.0 183.0 183.0 194.0 194.0 198.0 198.0 198.0 214.0 214.0 214.0 214.0 214.0 240.0 240.0 240.0 255.5 257.0 262.5 264.5 265.0 267.0 281.0 287.0 306.0 307.0 309.0 312.0 317.0 319.0 331.5 337.0 346.0 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178 178

Setting Weight Test Gap (kg) Pressure (x) (bar)15 15 15 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 1.5 2.3 2.3 2.5 2.5 2.5 2.5 2.5 2.7 2.7 2.7 2.7 2.7 2.7 2.7 3.2 3.2 3.8 3.8 3.8 3.8 3.8 3.8 3.3 3.3 4.2 4.2 4.2 4.8 4.8 4.8 4.8 4.8 4.0 4.0 4.0 8.6 8.7 8.9 9.0 9.0 9.1 9.7 9.9 10.9 11.0 11.0 11.3 11.5 11.6 12.2 12.4 12.7 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 56.0 56.0 56.0 55.4 55.0 52.5 52.4 52.4 51.9 48.3 46.9 53.8 53.0 53.0 62.9 61.1 61.1 57.8 56.9 55.0

8

DN225/9" DN250 DN225/9"


Viking Johnson 1999


GPS

QuickFit Couplings for pipes up to and including DN300/12"Pipe Nominal Pipe Type Pipe O.D. Tolerance Gasket (for distance L) QuickFit Unfitted Bolts Locating No. - Dia x Length Plugs No. off8 - M12 x 175 8 - M12 x 175 8 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 6 - M12 x 175 2 2 2 2 2 2 2 2 2 2 2 2 2 2

Viking Johnson

Dimensions A B C

Setting Weight Test Gap (kg) Pressure (x) (bar)20 20 20 20 20 20 20 20 20 20 20 20 20 20 13.4 13.3 13.4 13.6 13.7 13.8 15.0 15.3 15.5 15.5 15.7 15.8 16.1 16.2 52.3 52.3 52.3 51.0 50.0 50.0 45.5 52.3 52.3 52.3 43.0 43.0 42.0 41.7

DN250/10" DN250/10" DN250/10" DN280 DN250/10" DN250/10" DN315 DN300/12" DN300/12" DN300/12" DN300/12" DN300/12" DN300/12" DN300/12"

GRP* Steel/IPS/Imp PVC Metric Ductile Iron Metric PVC AWWA DI/PVC BS CI Metric PVC Steel/IPS/Imp PVC GRP * Metric Ductile Iron BS CI cl AB AWWA DI/PVC AWWA CI cl D BS CI cl CD

272.0 273.0 274.0 280.0 282.0 286.0 315.0 323.9 324.0 326.0 333.8 335.3 343.0 345.0

2.5 (100) +1.6,-0.8 (100) 2.5 (100) +0.9,-0.0 (100) 1.5 (100) 2.0 (100) +1.0,-0.0 (100) +1.6,-0.8 (100) 2.6 (100) 2.6 (100) 2.0 (100) 1.5 (100) 1.5 (100) 2.0 (100)

A1544 A1544 A1544 A1411 A1411 A1553 A1403 1515 A1549 A1549 A1555 A1412 A1554 A1554

527 527 527 754 754 637/754 1093 528/1093 528/1093 528/1093 585/773 585 585 585/773

359.0 150 178 360.0 150 178 361.0 150 178 367.0 150 178 369.0 150 178 373.0 150 178 402.0 150 178 411.0 150 178 411.0 150 178 413.0 150 178 421.0 150 178 422.5 150 178 430.0 150 178 432.0 150 178

* denotes Unfitted gasket only available Note: GRP* where mentioned in this table applies to pipe manufactured by the HOBAS method only. Pipe diameters have been extracted from tables produced by Johnston Pipes, a manufacturer of Hobas type GRP pipe. The dimensions for GRP in this table do not apply to Filament Wound GRP Pipe. The products previously marketed as MidiFit require different gaskets to those listed above. Please contact Viking Johnson Technical Department for further details.

L a rg e D i a m e t e r C o u p l i n g s f o r S t e e l P i p ePipe NominalDN350/14" DN400/16" DN450/18" DN500/20" DN550/22" DN600/24" DN650/26" DN700/28" DN750/30" DN800/32" DN850/34" DN900/36" DN1000/40" DN1050/42" DN1100/44" DN1200/48" DN1400/54" DN1600/66" DN1800/72" DN2000/80" DN2200/88" DN2300/92" DN2400/96" DN2500/100" DN2600/104" DN2700/108" DN2800/112" DN2900/116" DN3000/120"

Pipe O.D.355.6 406.4 457.0 508.0 559.0 610.0 660.0 711.0 762.0 813.0 864.0 914.0 1016.0 1067.0 1118.0 1220.0 1420.0 1620.0 1820.0 2020.0 2235.0 2340.0 2470.0 2540.0 2642.0 2743.0 2845.0 2946.0 3048.0

Tolerance (for distance L) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (150) 1.6 (150) 1.6 (150) 1.6 (150) +1.6,-3.0 (150) 3.0 (150) 3.0 (150) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200)

Gasket NumberJ51LS J53LS J55LS J57LS J59LS J60LS J61LS J63LS J64LS J65LS J66LS J67LS J71LS J72LS J73LS J74LS J125M J127M J130M J186H J188H J332X J334X J335X J336X J337X J338X J338X J339X

Bolts No. - Dia x Length6 - M12 x 235 8 - M12 x 235 8 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 16 - M16 x 265 20 - M16 x 265 24 - M16 x 265 28 - M16 x 400 28 - M16 x 400 36 - M16 x 400 36 - M16 x 430 40 - M16 x 430 48 - M16 x 430 48 - M16 x 430 48 - M16 x 430 48 - M16 x 430 48 - M16 x 430 48 - M16 x 430

A

Dimensions B C184 184 184 184 184 184 184 184 184 184 184 184 222 222 222 222 234 234 365 365 411 441 441 441 441 441 441 441 441 243 243 243 243 243 243 243 243 243 243 243 243 276 276 276 276 276 276 416 416 416 446 446 446 446 446 446 446 446

Setting Gap (x)25 25 25 25 25 25 25 25 25 25 25 25 40 40 40 40 40 40 55 55 55 55 55 55 55 55 55 55 55

Weight (kg)19.8 22.2 25.1 27.9 30.5 32.9 35.8 38.3 40.8 43.7 46.1 48.6 94.2 98.6 103.0 112.0 169.0 192.0 216.0 419.0 460.0 488.0 513.0 532.0 552.0 572.0 591.0 611.0 631.0

Test Pressure (bar)34.9 40.9 36.5 36.5 37.5 39.7 36.7 31.8 29.8 29.8 28.0 26.5 30.7 29.2 27.9 34.7 33.9 29.7 26.4 33.0 30.3 28.9 27.4 26.6 25.6 24.7 23.8 23.0 22.2

443 494 544 595 646 697 747 798 849 900 951 1001 1125 1176 1227 1329 1545 1745 1945 2154 2370 2475 2605 2675 2777 2878 2980 3081 3183

GPS

9


Viking Johnson 1999


L a rg e D i a m e t e r C o u p l i n g s f o r C a s t I ro n P i p ePipe NominalDN350/14" DN350/14" DN350/14" DN350/14" DN375/15" DN375/15" DN400/16" DN400/16" DN400/16" DN400/16" DN450/18" DN450/18" DN450/18" DN450/18" DN500/20" DN500/20" DN500 /20" DN525/21" DN525/21" DN550/22" DN550/22" DN600/24" DN600/24" DN600/24" DN600/24" DN650/26" DN650/26" DN675/27" DN675/27" DN800/30" DN800/30" DN800/30" DN800/30" DN800/30" DN800/30" DN825/33" DN900/36" DN900/36" DN900/36" DN900/36" DN900/36" DN900/36" DN1050/42" DN1050/42" DN1050/42" DN1050/42" DN1050/42" DN1050/42"

Viking Johnson

Pipe Type382 387 397 399 413 426 439 442 452 453 492 495 506 507 545 549 560 571 587 598 613 650 655 667 669 702 720 729 747 806 807 813 823 826 832 906 964 964 973 984 984 995 1121 1122 1130 1143 1145 1157 1172 1277 1283

Pipe O.D.AWWA CI Cl AB BS1211 Cl AB AWWA CI Cl CD BS 78 Cl CD BS1211 Cl AB BS 78 Cl CD BS1211 Cl AB AWWA CI Cl AB AWWA CI Cl CD BS 78 Cl CD BS1211 Cl AB AWWA CI Cl AB AWWA CI Cl CD BS 78 Cl CD BS1211 Cl AB AWWA CI Cl AB BS 78/AWWA Cl CD BS1211 Cl AB BS 78 Cl CD BS1211 Cl AB BS 78 Cl CD BS1211 Cl AB AWWA CI Cl AB BS 78 Cl CD AWWA CI Cl AB BS1211 Cl AB BS 78 Cl CD BS1211 Cl AB BS 78 Cl CD AWWA CI Cl A BS1211 Cl AB AWWA CI Cl B AWWA CI Cl C BS 78 Cl CD AWWA CI Cl D BS 78 Cl CD AWWA CI Cl A BS1211 Cl AB AWWA CI Cl B AWWA CI Cl C BS 78 Cl CD AWWA CI Cl D BS1211 Cl AB AWWA CI Cl A AWWA CI Cl B BS1211 Cl AB AWWA CI Cl C AWWA CI Cl D BS1211 Cl AB BS1211 Cl AB AWWA CI Cl A

Tolerance (for distance L)+1.25,-2.0 (150) 2.0 (125) +1.25,-2.0 (150) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) +1.25,-2.0 (150) +1.25,-2.0 (150) 2.0 (125) 2.0 (125) +1.25,-2.0 (150) +1.25,-2.0 (150) 2.0 (125) 2.0 (125) +1.25,-2.0 (150) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) +1.25,-2.0 (150) 2.0 (125) +1.25,-2.0 (150) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) +2.0,-1.5 (150) 2.0 (125) +2.0,-1.5 (150) +2.0,-1.5 (150) 2.0 (125) +2.0,-1.5 (150) 2.0 (150) +2.0,-1.5 (150) 2.0 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) 2.0 (150) +2.0,-1.5 (150) 2.0 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) 2.0 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) 2.0 (150) 2.0 (150) +2.0,-1.5 (150)

Gasket NumberJ52LS J52LS J53LS J53LS J53LS J54LS J55LS J55LS J55LS J55LS J57LS J57LS J57LS J57LS J58LS J69LS J59LS J59LS J59LS J60LS J60LS J61LS J61LS J62LS J62LS J62LS J63LS J63LS J63LS J65LS J65LS J65LS J65LS J65LS J65LS J67LS J70LS J70LS J70LS J70LS J70LS J70LS J73LS J73LS J73LS J73LS J73LS J73LS J73LS J122M J122M

Bolts Dimensions No. - Dia. x Length A B C8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 16 - M16 x 265 16 - M16 x 265 16 - M16 x 265 16 - M16 x 265 16 - M16 x 265 16 - M16 x 265 16 - M16 x 265 469 475 484 487 502 517 529 530 539 541 581 582 593 594 634 636 649 658 674 687 700 738 742 754 756 789 808 818 834 893 894 900 910 914 919 995 1073 1073 1082 1095 1095 1104 1230 1233 1241 1255 1257 1266 1281 1402 1407 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 222 222 222 222 222 222 222 222 222 222 222 222 222 234 234 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 276 276 276 276 276 276 276 276 276 276 276 276 276 276 276

Setting Gap (x)25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40

Weight (kg)21.4 21.7 22.2 22.3 23.0 23.7 24.3 24.4 24.9 24.9 26.9 27.0 27.9 27.9 29.8 30.0 30.6 31.1 31.8 32.5 33.1 35.3 35.5 36.2 36.2 37.8 38.8 39.2 40.0 43.3 43.4 43.7 44.2 44.3 44.5 48.3 89.8 89.8 90.6 91.7 91.7 92.4 103.0 103.0 104.0 106.0 106.1 107.0 111.0 152.0 153.0

Test Pressure (bar)42.9 42.9 41.6 41.6 40.3 39.1 37.9 36.8 36.8 36.8 33.9 33.9 41.1 41.1 38.4 37.4 37.4 36.7 35.7 35.7 35.7 37.2 36.3 36.3 36.3 33.2 33.2 33.2 32.4 29.9 29.9 29.9 29.9 29.9 29.9 26.7 32.3 32.3 32.3 32.3 32.3 32.3 27.8 27.8 37.0 37.0 37.0 37.0 37.0 37.3 37.3

10

DN1100/44" DN1200/48" DN1200/48"


Viking Johnson 1999


GPS

L a rg e D i a m e t e r C o u p l i n g s f o r C a s t I ro n P i p ePipe NominalDN1200/48" DN1200/48" DN1200/48" DN1200/48" DN1400/54" DN1400/54" DN1400/54" DN1400/54" DN1600/60" DN1600/60" DN1600/60" DN1600/60" DN2000/80" DN2000/80" DN2000/80" DN2000/80"

Viking Johnson

Pipe TypeAWWA CI Cl B BS 78 Cl CD AWWA CI Cl C AWWA CI Cl D AWWA CI Cl A AWWA CI Cl B AWWA CI Cl C AWWA CI Cl D AWWA CI Cl A AWWA CI Cl B AWWA CI Cl C AWWA CI Cl D AWWA CI Cl A AWWA CI Cl B AWWA CI Cl C AWWA CI Cl D

Pipe O.D.1290 1300 1305 1320 1439 1451 1468 1483 1595 1610 1630 1646 2223 2249 2275 2300

Tolerance (for distance L)+2.0,-1.5 (150) 2.0 (150) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200) +1.0,-2.5 (200)

Gasket Bolts Number No. - Dia. x LengthJ122M J122M J122M J124M J125M J125M J126M J126M J127M J127M J127M J128M J188H J331X J332X J332X 18 - M16 x 265 18 - M16 x 265 18 - M16 x 265 18 - M16 x 265 20 - M16 x 265 20 - M16 x 265 20 - M16 x 265 20 - M16 x 265 24 - M16 x 265 24 - M16 x 265 24 - M16 x 265 24 - M16 x 265 36 - M16 x 400 40 - M16 x 400 40 - M16 x 400 40 - M16 x 400

A

Dimensions B C234 234 234 234 234 234 234 234 234 234 234 234 365 365 365 365 276 276 276 276 276 276 276 276 276 276 276 276 416 416 416 416

Setting Gap (x)40 40 40 40 40 40 40 40 40 40 40 40 55 55 55 55

Weight (kg)153.0 155.0 155.0 157.0 171.0 172.0 174.0 176.0 189.0 191.0 193.0 196.0 458.0 470.0 475.0 480.0

Test Pressure (bar)36.6 18.0 18.0 18.0 20.0 20.0 20.0 20.0 30.1 29.9 29.5 29.2 30.4 30.1 29.8 29.4

1414 1425 1430 1445 1564 1576 1593 1608 1720 1736 1756 1771 2358 2384 2410 2435

L a rg e D i a m e t e r C o u p l i n g s f o r D u c t i l e I ro n P i p ePipe NominalDN350/14" DN350/14" DN400/16" DN400/16" DN450/18" DN450/18" DN500/20" DN500/20" DN600/24" DN600/24" DN700/28" DN800/30" DN800/30" DN900/36" DN900/36" DN1000/40" DN1050/42" DN1100/44" DN1200/48" DN1200/48" DN1400 DN1600 DN1800 DN2000

Pipe TypeBS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron BS/DIN Ductile Iron AWWA C151 Ductile Iron BS/DIN Ductile Iron BS/DIN Ductile Iron BS/DIN Ductile Iron BS/DIN Ductile Iron

Pipe O.D.378 388 429 442 480 495 532 549 635 655 738 813 842 945 973 1048 1130 1152 1255 1290 1462 1668 1876 2082

Tolerance (for distance L)+2.7,-3.5 (125) +1.25,-2.0 (150) +2.8,-4.0 (125) +1.25,-2.0 (150) +2.9,-4.0 (125) +1.25,-2.0 (150) +3.0,-4.0 (125) +1.25,-2.0 (150) +3.2,-4.5 (125) +1.25,-2.0 (150) +3.4,-4.5 (125) +2.0,-1.5 (150) +1.0,-4.5 (125) +1.0,-5.0 (150) +2.0,-1.5 (150) +1.0,-5.0 (150) +2.0,-1.5 (150) +1.0,-6.0 (150) +1.0,-6.0 (150) +2.0,-1.5 (150) +1.0,-7.0 (150) +1.0,-7.0 (150) +1.0,-7.0 (200) +1.0,-8.0 (200)

Gasket NumberJ52LS J52LS J54LS J55LS J56LS J57LS J58LS J69LS J61LS J61LS J63LS J65LS J65LS J70LS J70LS J71LS J73LS J73LS J122M J122M J125M J128M J135M J137M

Bolts No.- Dia. x Length8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 12 - M12 x 235 12 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 16 - M16 x 265 16 - M16 x 265 18 - M16 x 265 18 - M16 x 265 20 - M16 x 265 24 - M16 x 265 28 - M16 x 400 28 - M16 x 400

Dimensions A B C465 475 517 530 568 583 621 637 723 742 827 900 929 1054 1082 1157 1239 1260 1379 1414 1585 1793 2011 2217 184 184 184 184 184 184 184 184 184 184 184 184 222 222 222 222 222 222 234 234 234 234 365 365 243 243 243 243 243 243 243 243 243 243 243 243 243 276 276 276 276 276 276 276 276 276 416 416

Setting Gap (x)25 25 25 25 25 25 25 25 25 25 25 25 25 40 40 40 40 40 40 40 40 40 55 55

Weight (kg)21.2 21.7 23.7 24.4 26.2 27.0 29.2 30.0 34.2 35.5 39.6 43.7 45.0 88.4 90.6 97.0 104.0 106.0 150.0 153.0 173.0 198.0 222.0 245.0

Test Pressure (bar)43.9 43.9 38.8 38.8 34.8 34.8 39.3 39.3 38.1 38.1 32.8 28.7 43.4 33.0 33.0 29.7 36.7 36.7 37.9 37.9 32.9 28.8 35.4 32.5

GPS

11


Viking Johnson 1999


L a rg e D i a m e t e r C o u p l i n g s f o r P V C P i p ePipe NominalDN355 DN350/14" DN350/14" DN400 DN400/16" DN400/16" DN450 DN450/18" DN450/18" DN500 DN500/20" DN500/20" DN550/22" DN560 DN600/24" DN630 DN600/24" DN650/26" DN710 DN700/28" DN750/30" DN800 DN800/30" DN900 DN900/36" DN900/36" DN1000 DN1000/40" DN1100/44" DN1200 DN1200/48" DN1400 DN1400/54" DN1600 DN1600/66" DN1800 DN1800/72" DN2000

Viking JohnsonSetting Gap (x)25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 40 40 40 40 40 40 40 40 40 40 40 40 55

Pipe TypeMetric PVC Imperial/IPS PVC AWWA C900 PVC Metric PVC Imperial/IPS PVC AWWA C900 PVC Metric PVC Imperial/IPS PVC AWWA C900 PVC Metric PVC Imperial/IPS PVC AWWA C900 PVC Imperial PVC Metric PVC Imperial/IPS PVC Metric PVC AWWA C900 PVC Imperial PVC Metric PVC Imperial PVC Imperial/IPS PVC Metric PVC AWWA C900 PVC Metric PVC Imperial/IPS PVC AWWA C900 PVC Metric PVC Imperial PVC Imperial PVC Metric PVC Imperial PVC Metric PVC Imperial PVC Metric PVC Imperial PVC Metric PVC Imperial PVC Metric PVC

Pipe O.D.355 355.6 388 400 406.4 442 450 457 495 500 508 549 559 560 610 630 655 660 710 711 762 800 813 900 914 973 1000 1016 1118 1200 1220 1400 1420 1600 1620 1800 1820 2000

Tolerance (for distance L)+1.1,-0.0 (125) 0.4 (125) 0.4 (125) +1.2,-0.0 (125) 0.5 (125) 0.5 (125) +1.4,-0.0 (125) 0.5 (125) 0.5 (125) +1.5,-0.0 (125) 0.6 (125) 0.6 (125) 0.6 (125) +1.7,-0.0 (125) 0.8 (125) +1.9,-0.0 (125) 0.8 (125) 0.8 (125) +2.2,-0.0 (125) 0.8 (125) 1.0 (125) +2.4,-0.0 (125) 1.0 (125) +2.7,-0.0 (125) 1.25 (125) 1.25 (125) +3.0,-0.0 (150) 1.6 (150) 1.6 (150) +3.6,-0.0 (150) 1.6 (150) +4.2,-0.0 (150) 1.6,-3.2 (150) +4.8,-0.0 (150) 3.2 (150) +5.4,-0.0 (150) 3.2 (150) +6.0,-0.0 (150)

Gasket NumberJ51LS J51LS J52LS J53LS J53LS J55LS J55LS J55LS J57LS J57LS J57LS J69LS J59LS J59LS J60LS J61LS J61LS J61LS J63LS J63LS J64LS J64LS J65LS J67LS J67LS J70LS J71LS J71LS J73LS J74LS J121M J125M J125M J127M J127M J130M J130M J137M

Bolts No.- Dia. x Length6 - M12 x 235 6 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 10 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 12 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 14 - M16 x 265 16 - M16 x 265 10 - M16 x 265 20 - M16 x 265 20 - M16 x 265 24 - M16 x 265 20 - M16 x 265 28 - M16 x 265 28 - M16 x 265 28 - M16 x 400

Dimensions A B C442 443 475 487 494 530 537 545 583 587 595 637 646 649 697 717 742 748 797 799 849 888 900 987 1002 1082 1110 1125 1227 1309 1345 1525 1545 1726 1745 1926 1945 2135 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 184 222 222 222 222 222 234 234 234 234 234 234 234 365 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 276 276 276 276 276 276 276 276 276 276 276 276 416

Weight Test (kg) Pressure (bar)19.7 19.8 21.7 22.3 22.6 24.4 24.7 25.1 27.0 27.2 27.9 30.0 30.5 30.6 32.9 33.9 35.5 35.8 38.3 38.3 40.8 43.0 43.7 47.9 48.6 90.6 93.0 94.2 103.0 110.0 145.0 166.0 169.0 190.0 192.0 214.0 216.0 235.0 34.9 34.9 40.9 40.9 40.9 36.5 36.5 36.5 41.1 41.1 41.1 37.5 37.5 37.5 39.7 39.7 36.7 36.7 34.0 34.0 31.8 29.8 29.8 26.5 26.5 30.7 30.7 30.7 27.9 34.7 34.7 33.9 33.9 29.7 29.7 26.4 26.4 33.5


Viking Johnson 1999


GPS

L a rg e D i a m e t e r C o u p l i n g s f o r G R P P i p ePipe NominalDN350/14" DN400/16" DN450/18" DN500/20" DN600/24" DN700/28" DN800/32" DN900/36" DN1000/40" DN1100/44" DN1200/48" DN1300/52" DN1400/54" DN1500/60" DN1600/66" DN1700/68" DN1800/72" DN1900/76" DN2000/80" DN2100/84" DN2200/88" DN2400/96" DN2500/100" DN2700/108"

Viking JohnsonWeight (kg)21.1 23.7 26.1 29.1 34.0 38.6 44.0 86.4 95.1 137.0 147.0 160.0 172.0 183.0 194.0 208.0 383.0 402.0 424.0 436.0 470.0 500.0 535.0 573.0

Pipe O.D.376 427 478 530 633 718 820 924 1027 1144 1228 1350 1449 1536 1640 1742 1844 1946 2048 2108 2252 2400 2558 2747

Tolerance (for distance L) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (125) 1.6 (150) 1.6 (150) 1.6 (150) 1.6 (150) +1.6,-3.0 (150) +1.6,-3.0 (150) 3.0 (150) 3.0 (150) 3.0 (150) 3.0 (150) 3.0 (150) 3.0 (150) 3.0 (200) 3.0 (200) 3.0 (200) 3.0 (200)

Gasket NumberJ52LS J54LS J56LS J58LS J61LS J63LS J65LS J67LS J71LS J120M J122M J124M J125M J126M J127M J129M J184H J185H J186H J187H J331X J333X J335X J337X

Bolts No.- Dia. x Length8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 10 - M12 x 235 10 - M12 x 235 12 - M12 x 235 14 - M12 x 235 14 - M12 x 235 14 - M16 x 265 16 - M16 x 265 18 - M16 x 265 18 - M16 x 265 20 - M16 x 265 24 - M16 x 265 24 - M16 x 265 28 - M16 x 265 32 - M16 x 400 32 - M16 x 400 36 - M16 x 400 36 - M16 x 400 40 - M16 x 430 40 - M16 x 430 48 - M16 x 430 48 - M16 x 430

A

Dimensions B C184 184 184 184 184 184 222 222 222 222 234 234 234 234 234 234 365 365 365 365 365 365 365 365 243 243 243 243 243 243 243 276 276 276 276 276 276 276 276 276 416 416 416 416 446 446 446 446

Setting Gap (x)25 25 25 25 25 25 25 25 40 40 40 40 40 40 40 40 55 55 55 55 55 55 55 55

Test Pressure (bar)44.2 39.1 34.9 39.2 38.2 33.7 29.5 33.6 30.3 36.9 38.7 35.3 33.2 31.3 29.3 27.6 36.0 34.1 33.1 32.3 30.1 28.2 26.5 24.7

463 517 565 618 720 805 908 1033 1136 1270 1352 1474 1573 1660 1766 1868 1978 2081 2183 2243 2387 2535 2692 2882

Note: This table applies to pipe manufactured by the HOBAS method only. Pipe diameters have been extracted from tables produced by Johnston Pipes, a manufacturer of Hobas type GRP pipe. This table does not apply to Filament Wound GRP Pipe.

JunoJUNO COUPLING STEEL x STEELPipe Diameter Joins To0.5" 0.75" 1" 1.25" 1.5" 2" 0.5" 0.75" 1" 1.25" 1.5" 2"

A45.0 51.6 58.0 68.5 75.6 89.0

Dimensions B B(locking) (non locking)78 81 90 90 115 81 74 76 85 83 83 107

T4.0 4.0 4.0 4.0 4.0 4.25

Weight (kg)0.4 0.5 0.5 0.7 0.9 1.1

JUNO COUPLING PE TO PE (mm)Pipe Diameter Joins To25 32 63 25 32 63

A51.6 58.0 93.0

Dimensions B T81 90 116 4.0 4.0 4.25

Weight (kg)0.5 0.7 1.8

GPS


Viking Johnson 1999


Stepped Couplings

Viking Johnson

Expanded Sleeve Stepped Coupling

Stepped Coupling with make up ring

AquaGrip Stepped Coupling

BOLT TORQUE TABLE FOR STEPPED COUPLINGSPRODUCT COATING BOLT SIZE M12 M16 ALL PRODUCTS EXCEPT AQUAGRIP BLACK RILSAN TORQUE lbf.ft Nm 40 - 50 55 - 65 70 - 80 95 - 110 AQUAGRIP BLACK RILSAN TORQUE lbf.ft Nm 55-60 70-75 BLUE SHERAPLEX TORQUE lbf.ft Nm 40-50 55-65 -

14


GPS

MaxiStep CouplingsMin47.9 59.5 59.5 88.1 88.1 88.1 95.8 95.8 107.2 107.2 109.6 109.6 109.6 132.2 132.2 132.2 138.9 138.9 158.2 159.2 192.9 192.9 218.0 230.0 250.0 272.0 315.0 315.0 322.9 322.9 374.5 394.3 404.8 425.0 425.0 425.0 476.0 476.0 476.0 527.0 527.0 527.0 527.0 630.0 630.0 630.0

Viking JohnsonBolts No. - Dia x Length4 - M12 x 215 4 - M12 x 195 4 - M12 x 195 4 - M12 x 195 4 - M12 x 195 4 - M12 x 195 4 - M12 x 195 4 - M12 x 195 4 - M12 x 175 4 - M12 x 175 4 - M12 x 175 4 - M12 x 215 4 - M12 x 215 4 - M12 x 175 4 - M12 x 195 4 - M12 x 215 4 - M12 x 195 4 - M12 x 215 4 - M12 x 195 4 - M12 x 215 4 - M12 x 255 5 - M12 x 255 5 - M12 x 255 6 - M12 x 255 6 - M12 x 255 6 - M12 x 255 8 - M12 x 255 8 - M12 x 255 8 - M12 x 255 8 - M12 x 255 8 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 10 - M12 x 340 12 - M12 x 340 12 - M12 x 340 12 - M12 x 340 12 - M12 x 340 14 - M12 x 340 14 - M12 x 340 14 - M12 x 340

Small End Max Gasket59.5 72.0 72.0 102.4 102.4 102.4 108.8 108.8 115.1 115.1 127.8 127.8 127.8 146.0 146.0 146.0 153.2 153.2 169.9 181.6 209.0 209.0 235.0 247.0 267.0 289.0 332.0 332.0 339.4 339.4 391.5 411.3 421.8 442.0 442.0 442.0 493.0 493.0 493.0 544.0 544.0 544.0 544.0 647.0 647.0 647.0 1637 1613 1613 1615 1615 1615 1674 1674 1620 1620 1759 1759 1759 1635 1635 1635 1633 1633 1621 1760 1758 1653 1654 1756 1655 1656 1738 1738 1657 1657 1659 1766 1767 1662 1662 1662 1770 1770 1770 1773 1773 1773 1773 1778 1778 1778

Min72.2 72.2 88.1 95.8 107.2 109.6 107.2 109.6 109.6 118.0 118.0 132.2 138.9 138.9 158.2 159.2 158.2 159.2 159.2 171.5 218.1 218.1 230.0 250.0 272.0 291.0 322.9 332.0 332.0 348.5 394.3 418.2 425.0 434.5 447.2 455.0 487.3 501.9 510.0 540.1 555.3 566.5 582.2 645.2 662.0 675.0

Large End Max Gasket85.0 85.0 102.4 108.8 115.1 127.8 115.1 127.8 127.8 131.5 131.5 146.0 153.2 153.2 169.9 181.6 169.9 181.6 181.6 193.0 235.0 235.0 247.0 267.0 289.0 308.0 339.4 349.0 349.0 365.5 411.3 435.2 442.0 451.4 464.2 472.0 504.3 518.9 527.0 557.1 572.3 583.5 599.2 662.2 679.0 692.0 1614 1614 1615 1674 1620 1759 1620 1759 1759 1616 1616 1635 1633 1633 1621 1760 1621 1760 1760 6006 1757 1654 1756 1655 1656 6007 1657 1658 1658 6008 1766 1784 1662 1768 1769 6003 1771 1772 6004 1774 1775 1776 1777 1779 1780 6005

Overall Dimensions A A1 B C150 164 164 198 198 198 202 202 223 223 223 223 223 250 250 250 198 250 280 274 321 321 345 357 379 399 444 444 452 450 502 522 532 552 552 552 603 603 603 654 657 657 657 757 757 757 177 177 198 201 225 212 225 212 212 226 226 250 250 250 280 274 280 274 274 285 347 347 357 279 401 418 452 461 461 476 522 545 552 562 574 582 615 629 637 667 683 694 709 772 789 802 165 165 165 165 165 165 165 165 140 140 140 180 180 140 165 180 165 180 165 180 230 230 230 230 230 230 230 230 225 225 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 223 203 203 203 203 203 203 203 178 178 178 223 223 178 203 223 203 223 203 223 268 268 268 268 268 268 268 268 268 268 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348 348

Setting Gap (x)20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

Weight (kg)3.6 4.3 4.5 4.6 5.9 5.4 5.3 5.4 4.4 4.5 4.2 6.7 6.7 7.4 10.4 10.6 7.7 7.8 6.6 8.3 10.1 15.3 16.4 17.4 18.5 19.5 21.9 22.3 22.0 23.0 34.5 36.5 37.5 38.9 39.1 39.5 42.7 43.0 43.6 47.4 47.6 47.8 48.0 55.8 56.1 57.0

GPS


Viking Johnson 1999


A q u a G r i p Tr a n s i t i o n a l C o u p l i n gPipe O.D. (mm)63 90 90 110 110 125 125 160 160 160 180 180

Viking Johnson

SDR Rating11 11 17 / 17.6 11 17 / 17.6 11 17 / 17.6 11 17 / 17.6 26 11 17 / 17.6

PE End No. of Gripper Segments Full Half10 14 14 17 17 19 19 24 24 24 26 26 1 -

Gasket

Through Stud Bolts Bolts Type No.- Dia x Length No.- Dia x Length2 - M12 x 210 4 - M12 x 210 4 - M12 x 210 4 - M12 x 210 4 - M12 x 210 4 - M12 x 210 4 - M12 x 210 8 - M12 x 125 8 - M12 x 125 8 - M12 x 125 8 - M12 x 125 8 - M12 x 125 1 1 1 1 1 2 2 3 3 3 3 3

MaxiFit End Diameter Stud Dimensions Setting Gap Weight Range Gasket Bolts A A1 B C (x) (kg) Min Max No.- Dia x Length Min Max59.5 88.1 88.1 109.6 109.6 109.6 109.6 159.2 159.2 159.2 159.2 159.2 72.0 102.4 102.4 127.8 127.8 127.8 127.8 181.6 181.6 181.6 181.6 181.6 1613 1615 1615 1759 1759 1759 1759 1760 1760 1760 1760 1760 4 - M12 x 125 4 - M12 x 145 4 - M12 x 145 4 - M12 x 125 4 - M12 x 115 144.0 167.5 165 210 167.5 197.5 168 210 167.5 197.5 168 210 188.0 219.5 163 210 188.0 219.5 163 210 203.0 219.5 163 210 203.0 219.5 163 210 240.0 282.0 202 240 240.0 282.0 202 240 240.0 282.0 202 240 257.5 282.0 186 208 257.5 282.0 186 208 20 20 20 20 20 20 20 20 20 20 20 20 40 40 40 40 40 40 40 40 40 40 40 40 2.8 3.6 3.7 5.0 5.0 4.3 4.4 15.1 15.2 15.3 16.2 16.2

6001 1785 1785 1786 1786 1787 1787 1788 1788 1788 1789 1789

Large Diameter Stepped Coupling Metric Ductile Iron to Cast IronPipe Type Pipe Nominal Pipe Gasket O.D. Tolerance (for distance L)+2.7,-3.5 (125) +2.7,-3.5 (125) 2.0 (125) 2.0 (125) +2.9,-4.0 (125) +2.9,-4.0 (125) +2.8,-4.0 (125) +2.8,-4.0 (125) +3.0,-4.0 (125) +3.0,-4.0 (125) 2.0 (125) +3.2,-4.5 (125) +3.2,-4.5 (125) 2.0 (125) +3.4,-4.5 (125) +3.4,-4.5 (125) +3.4,-4.5 (125) 2.0 (125) 2.0 (125) +1.0,-4.5 (125) +1.0,-4.5 (125) +1.0,-5.0 (150) +1.0,-5.0 (150) +1.0,-5.0 (150) +1.0,-5.0 (150) 2.0 (150) 2.0 (150) +1.0,-6.0 (150) +1.0,-6.0 (150)

Pipe Type

Pipe Nominal

Pipe O.D.

Gasket Tolerance (for distance L)J52LS J53LS J54LS J54LS J55LS J55LS J57LS J57LS J58LS J59LS J61LS J61LS J62LS J63LS J63LS J64LS J64LS J65LS J65LS J66LS J66LS J70LS J70LS J72LS J72LS J121M J121M J122M J122M 2.0 (125) 2.0 (125) +2.9,-4.0 (125) +2.9,-4.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) 2.0 (125) +3.2,-4.5 (125) 2.0 (125) 2.0 (125) +3.4,-4.5 (125) 2.0 (125) 2.0 (125) 2.0 (125) +1.0,-4.5 (125) +1.0,-4.5 (125) 2.0 (125) 2.0 (125) 2.0 (150) 2.0 (150) 2.0 (150) 2.0 (150) +1.0,-6.0 (150) +1.0,-6.0 (150) 2.0 (150) 2.0 (150)

Bolts No.- Dia x Length8 - M12x235 8 - M12x235 8 - M12x235 8 - M12x235 8 - M12x235 8 - M12x235 8 - M12x235 8 - M12x235

A

Dimensions Setting Weight A1 B C Gap (kg) (x)474.5 184 487.0 184 516.5 184 516.5 184 528.5 184 541.0 184 581.0 184 594.0 184 633.5 184 649.0 184 723.0 184 738.0 184 754.0 184 826.5 184 833.5 184 843.0 184 860.0 284 928.0 184 928.0 184 947.5 184 966.5 298 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 243 341 243 243 243 346 250 346 250 346 275 275 275 346 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 40 40 40 40 40 40 40 40 21.3 21.5 23.1 23.5 23.8 24.0 26.4 26.9 29.3 29.5 33.3 34.7 34.9 39.3 39.7 39.8 53.6 45.0 44.4 45.2 60.7 88.5 104.7 97.2 115.0 135.2 137.0 150.4 176.6

Ductile Iron Ductile Iron Cast Iron Cl AB Cast Iron Cl CD Ductile Iron Ductile Iron Ductile Iron Ductile Iron Ductile Iron Ductile Iron Cast Iron Cl CD Ductile Iron Ductile Iron Cast Iron Cl AB Ductile Iron Ductile Iron Ductile Iron Cast Iron Cl AB Cast Iron Cl CD Ductile Iron Ductile Iron Ductile Iron Ductile Iron Ductile Iron Ductile Iron Cast Iron Cl AB Cast Iron Cl CD Ductile Iron

DN350/14" DN350/14" DN375/15" DN375/15" DN400/16" DN400/16" DN450/18" DN450/18" DN500/20" DN500/20" DN550/22" DN600/24" DN600/24" DN675/27" DN700/28" DN700/28" DN700/28" DN750/30" DN750/30 DN800/32" DN800/32" DN900/36" DN900/36" DN1000/40" DN1000/40" DN1050/42" DN1050/42" DN1200/48" DN1200/48"

378 378 413 426 429 429 480 480 532 532 613 635 635 729 738 738 738 807 826 842 842 945 945 1048 1048 1121 1143 1255 1255

J52LS J52LS J53LS J54LS J54LS J54LS J56LS J56LS J58LS J58LS J60LS J61LS J61LS J63LS J63LS J63LS J63LS J65LS J65LS J65LS J65LS J70LS J70LS J71LS J71LS J120M J120M J122M J122M

Cast Iron Cl AB Cast Iron Cl CD Ductile Iron Ductile Iron Cast Iron Cl AB Cast Iron Cl CD Cast Iron Cl AB Cast Iron Cl CD Cast Iron Cl AB Cast Iron Cl CD Ductile Iron Cast Iron Cl AB Cast Iron Cl CD Ductile Iron Cast Iron Cl CD Cast Iron Cl AB Cast Iron Cl CD Ductile Iron Ductile Iron Cast Iron Cl AB Cast Iron Cl CD Cast Iron Cl AB Cast Iron Cl CD Cast Iron Cl AB Cast Iron Cl CD Ductile Iron Ductile Iron Cast Iron Cl AB Cast Iron Cl CD

DN350/14" DN350/14" DN400/16" DN400/16" DN400/16" DN400/16" DN450/18" DN450/18" DN500/20" DN500/20" DN600/24" DN600/24" DN600/24" DN700/28" DN675/27" DN700/28" DN700/28" DN800/32" DN800/32" DN800/32" DN800/32" DN900/36" DN900/36" DN1000/40" DN1000/40" DN1100/42" DN1100/42" DN1200/48" DN1200/48"

387 399 429 429 439 453 492 507 545 560 635 650 667 738 747 755 773* 842 842 860 879* 964 984* 1068 1090* 1152 1152 1276 1300*

465.5 465.5 501.5 513.0 516.5 516.5 568.0 568.0

10 - M12x235 620.5 10 - M12x235 620.5 10 - M12x235 700.0 12 - M12x235 723.0 12 - M12x235 723.0 12 - M12x235 817.5 12 - M12x235 826.5 12 - M12x235 826.5 12 - M12x330 826.5 14 - M12x235 894.0 14 - M12x235 914.0 14 - M12x235 928.0 14 - M12x335 928.0

14 - M16x265 1054.0 1073.0 222 14 - M16x335 1054.0 1095.0 298 14 - M16x265 1156.0 1179.0 222 14 - M16x335 1156.0 1200.0 298 16 - M16x265 1245.0 1275.0 234 16 - M16x265 1269.0 1275.0 234 18 - M16x265 1378.5 1400.5 234 18 - M16x335 1378.5 1426.0 310

16

Ductile Iron

* Denotes long sleeve coupling due to size of step


Viking Johnson 1999


GPS

Large Diameter Stepped Coupling Metric Ductile Iron to Metric PVCPipe TypeMetric PVC Ductile Iron Ductile Iron Metric PVC Ductile Iron Metric PVC Ductile Iron Metric PVC Metric PVC Metric PVC

Viking Johnson

Pipe NominalDN355 DN350/14" DN400/16" DN450 DN450/18" DN500 DN500/20" DN630 DN710 DN800

Pipe Gasket Tolerance O.D. (for distance L)355 378 429 450 480 500 532 630 710 800 J51LS J52LS J54LS J55LS J56LS J57LS J58LS J61LS J63LS J65LS +1.1,-0.0 (125) +2.7,-3.5 (125) +2.9,-4.0 (125) +1.4,-0.0 (125) +2.8,-4.0 (125) +1.5,-0.0 (125) +3.0,-4.0 (125) +1.9,-0.0 (125) +2.2,-0.0 (125) +2.4,-0.0 (125)

Pipe Type

Pipe Nominal

Pipe Gasket Tolerance O.D. (for distance L)378 400 450 480 500 532 560 635 738 842 J52LS J53LS J55LS J56LS J57LS J58LS J59LS J61LS J63LS J65LS +2.7,-3.5 (125) +1.2,-0.0 (125) +1.4,-0.0 (125) +2.8,-4.0 (125) +1.5,-0.0 (125)

Bolts No. - Dia x Length8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235 8 - M12 x 235

A443 463 517 537 568 587 621 717 800 887

Dimensions Setting Weight A1 B C Gap (kg) (x)465.5 490.5 537.0 568.0 587.0 620.5 649.0 723.0 826.5 928.0 184 184 184 184 184 184 184 184 184 184 243 243 243 243 243 243 243 243 243 243 25 25 25 25 25 25 25 25 25 25 20.4 22.6 23.9 25.0 26.4 28.0 29.5 33.9 38.6 43.5

Ductile Iron DN350/14" Metric PVC Metric PVC DN400 DN450

Ductile Iron DN450/18" Metric PVC DN500

Ductile Iron DN500/20" Metric PVC DN560

+3.0,-4.0 (125) 10 - M12 x 235 +1.7,-0.0 (125) 10 - M12 x 235 +3.2,-4.5 (125) 10 - M12 x 235 +3.4,-4.5 (125) 12 - M12 x 235 +1.0,-4.5 (125) 14 - M12 x 235

Ductile Iron DN600/24" Ductile Iron DN700/28" Ductile Iron DN800/32"

Large Diameter Stepped Coupling AWWA Ductile Iron to Cast IronPipe TypeAWWA C151 AWWA C151 AWWA C151 AWWA C151 AWWA C151 Cast Iron A AWWA C151 AWWA C151 Cast Iron A AWWA C151 AWWA C151 Cast Iron A AWWA C151 AWWA C151 Cast Iron A AWWA C151 AWWA C151

Pipe NominalDN350/14" DN400/16" DN450/18" DN500/20" DN600/24" DN750/30" DN750/30" DN750/30" DN900/36" DN900/36" DN900/36" DN1050/42" DN1050/42" DN1050/42" DN1200/48" DN1200/48" DN1200/48"

Pipe O.D.382 442 495 548 655 806 813 813 964 973 973 1122 1130 1130 1282 1290 1290

Gasket

Tolerance (for distance L)+1.25,-2.0 (150) +1.25,-2.0 (150) +1.25,-2.0 (150) +1.25,-2.0 (150) +1.25,-2.0 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150)

Pipe TypeCast Iron CD Cast Iron CD Cast Iron CD Cast Iron CD Cast Iron CD AWWA C151 Cast Iron C Cast Iron D AWWA C151 Cast Iron C Cast Iron D AWWA C151 Cast Iron C Cast Iron D AWWA C151 Cast Iron C Cast Iron D

Pipe NominalDN350/14 DN400/16 DN450/18 DN500/20 DN600/24 DN750/30 DN750/30 DN750/30 DN900/36 DN900/36 DN900/36 DN1050/42 DN1050/42 DN1050/42 DN1200/48 DN1200/48 DN1200/48

Pipe Gasket Tolerance O.D. (for distance L)398 452 506 560 669 813 823 832 973 983 995 1130 1145 1157 1290 1305 1320 J53LS J55LS J57LS J59LS J62LS J65LS J65LS J65LS J70LS J70LS J70LS J120M J120M J121M J122M J124M J124M +1.25,-2.0 (150) +1.25,-2.0 (150)

Bolts No. Dia x Length8 - M12x235 8 - M12x235

A

Dimensions Setting Weight A1 B C Gap (kg) (x)184 243 184 243 184 243 184 243 184 243 184 243 184 243 184 243 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 30 30 22.7 25.6 28.7 31.1 36.7 44.7 44.8 44.9 89.5 90.4 91.2 134.3 136.1 136.3 152.7 178.3 180.0

J52LS J55LS J57LS J58LS J61LS J65LS J65LS J65LS J70LS J70LS J70LS J120M J120M J120M J122M J122M J122M

469.0 499.5 531.5 539.5

+1.25,-2.0 (150) 10 - M12x235 582.5 593.0 +1.25,-2.0 (150) 10 - M12x235 636.5 649.0 +1.25,-2.0 (150) 12 - M12x235 742.0 755.0 +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) +2.0,-1.5 (150) 14 - M12x235 893.5 901.0 14 - M12x235 900.0 911.0 14 - M12x235 900.0 919.5

14 - M16x265 1073.0 1082.0 222 250 14 - M16x265 1082.0 1093.0 222 250 14 - M16x265 1082.0 1094.5 222 250 16 - M16x265 1246.0 1254.5 234 275 16 - M16x265 1254.5 1271.0 234 275 16 - M16x265 1254.5 1280.0 234 275 16 - M16x265 1403.5 1414.0 234 275 18 - M16x265 1414.0 1427.5 310 346 18 - M16x265 1414.0 1443.5 310 346

* Viking Johnson can manufacture Large Diameter Stepped Couplings to join any pipe material to any other pipe material (with the exception of PE pipe). The above tables are only a small selection of the possible variety of stepped couplings that can be produced.

GPS


Viking Johnson 1999


JunoJUNO TRANSITIONAL COUPLING STEEL x STEELPipe Diameter Joins To0.5" 0.75" 1" 1.25" 1" 1" 0.75" 1" 1.5" 1.5" 1.25" 1.5"

Viking Johnson

A(small end) 45.0 51.6 58.0 68.5 58.0 58.0

Dimensions A B

B

T

(large end) (locking) (non locking) 51.6 58.0 75.6 75.6 68.5 75.6 90 90 90 90 90 90 76 85 85 83 83 83 4.0 4.0 4.0 4.25 4.0 4.0

Weight (kg)0.5 0.5 0.5 0.9 0.7 0.8

ST x ST

JUNO TRANSITIONAL COUPLING PE x PE (mm)Pipe Diameter Joins To20 25 25 32

A(small end) 45.0 51.6

Dimensions A B(large end) 51.6 58.0 90 90

T4.0 4.0

Weight (kg)0.5 0.6

PE x PE

JUNO TRANSITIONAL COUPLING STEEL x PEPipe Diameter Joins To0.5" 0.75" 0.5" 0.75" 1" 1" 1.25" 1.25" 1.5" 2" 20 20 25 25 25 32 32 40 50 63

A(steel end) 45.0 51.6 45.0 51.6 58.0 58.0 68.5 68.5 75.6 89.0

Dimensions A B(PE end) 45.0 45.0 51.6 51.6 51.6 58.0 58.0 68.5 80.0 93.0 78 81 81 81 90 90 90 90 104 116

T4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.25 4.25 4.25

Weight (kg)0.4 0.5 0.5 0.5 0.6 0.6 0.7 0.7 1.0 1.7

PE x ST


Viking Johnson 1999


GPS

Flange Adaptors

Viking Johnson

MaxiFit Flange Adaptor

AquaGrip (DN225 - DN1400)

AquaGrip (DN63 to DN180)

FlexLock Flange Adaptor

PRESSURE RATINGSViking Johnson flange adaptors are supplied to suit the pressure rating of the flange, unless specifically ordered otherwise. The overall pressure rating of the assembled adaptor will be equal to that of the lower rated component, either pipe or flange. e.g. PN10 flange adaptors have a flange rated at a working pressure of 10bar (150 psi). The coupling component of the flange adaptor will invariably have a higher pressure rating than the flange.

Flange Adaptor - General

BOLT TORQUE TABLEPRODUCT COATING BOLT SIZE M12 M16 M20 M24 M27 M30 M33 ALL PRODUCTS EXCEPT AQUAGRIP BLACK RILSAN TORQUE lbf.ft Nm 40 - 50 55 - 65 70 - 80 95 - 110 110 - 120 150 - 165 210 - 220 285 - 300 260 - 300 350 - 405 400 - 420 500 - 575 500 - 550 675 - 750 AQUAGRIP BLACK RILSAN TORQUE lbf.ft Nm 55-60 70-75 BLUE SHERAPLEX TORQUE lbf.ft Nm 40-50 55-65 FLURENE TORQUE lbf.ft Nm 70 - 80 95 - 110 110 - 120 150 - 165 210 - 220 285 - 300 260 - 300 350 - 405 400 - 420 500 - 575 500 - 550 675 - 750

GPS


19

MaxiDaptor DN50/2" to DN600/24"Tolerance Min Max59.5 72.2 72.2 88.1 93.0 109.6 109.6 118.0 132.2 138.9 159.2 192.9 218.1 218.1 250.0 250.0 272.0 272.0 322.9 322.9 332.2 332.2 332.2 351.0 351.0 351.0 374.5 374.5 374.5 386.0 394.3 394.3 394.3 404.8 404.8 404.8 418.2 418.2 425.0 425.0 425.0 434.4 434.4 439.0 447.2 447.2 455.0 455.0 455.0 476.0 476.0 487.3 487.3 487.3 492.0 501.9 501.9 501.9 510.0 510.0 510.0 527.0 527.0 527.0 540.1 540.1 72.0 85.0 85.0 102.4 107.0 127.8 127.8 131.5 146.0 153.2 181.6 209.0 235.0 235.0 267.0 267.0 289.0 289.0 339.4 339.4 349.0 349.0 349.0 368.0 368.0 368.0 391.5 391.5 391.5 403.0 411.3 411.3 411.3 421.8 421.8 421.8 435.2 435.2 442.0 442.0 442.0 451.4 451.4 456.0 464.2 464.2 472.0 472.0 472.0 493.0 493.0 504.3 504.3 504.3 509.0 518.9 518.9 518.9 527.0 527.0 527.0 544.0 544.0 544.0 557.1 557.1

Viking JohnsonDimensions A1 B C165 185 200 220 220 229 229 229 279 279 285 340 340 340 405 406 405 405 483 460 460 460 483 505 520 533 505 520 533 533 505 520 533 565 580 597 565 580 565 580 597 580 597 597 580 597 615 640 635 615 640 640 715 635 635 640 715 635 615 640 637 670 715 698 715 698 100 100 100 100 105 100 100 100 100 100 106 100 100 100 113 126 113 113 113 113 126 105 118 179 179 177 179 179 177 261 271 271 261 179 179 177 177 177 179 179 177 271 182 182 271 266 184 184 182 184 184 184 184 266 266 271 184 266 271 271 266 184 184 182 184 266 116 116 116 116 118 116 116 116 116 116 131 130 130 130 143 138 143 143 143 143 143 138 138 218 218 218 218 218 218 218 303 303 218 218 218 218 218 218 218 218 218 303 303 303 303 303 218 218 303 218 218 218 218 303 303 303 218 303 303 303 303 218 218 303 218 303

Flange Details

Gasket

Tee Bolts No. - Dia x Length2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 120 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 6 - M12 x 120 6 - M12 x 125 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 135 6 - M12 x 125 6 - M12 x 125 8 - M12 x 205 8 - M12 x 205 6 - M12 x 205 8 - M12 x 205 8 - M12 x 205 6 - M12 x 205 6 - M12 x 290 8 - M12 x 290 8 - M12 x 290 6 - M12 x 290 8 - M12 x 205 8 - M12 x 205 8 - M12 x 205 8 - M12 x 205 8 - M12 x 205 8 - M12 x 205 8 - M12 x 205 8 - M12 x 205 8 - M12 x 290 8 - M12 x 205 8 - M12 x 205 8 - M12 x 290 8 - M12 x 290 10 - M12 x 205 10 - M12 x 205 8 - M12 x 205 10 - M12 x 205 10 - M12 x 205 10 - M12 x 205 10 - M12 x 205 8 - M12 x 290 8 - M12 x 290 10 - M12 x 290 10 - M12 x 205 8 - M12 x 290 10 - M12 x 290 10 - M12 x 290 8 - M12 x 290 10 - M12 x 205 10 - M12 x 205 10 - M12 x 205 10 - M12 x 205 10 - M12 x 290

A164.0 177.0 177.0 173.0 202.0 198.5 198.5 226.0 248.5 248.5 261.0 319.0 345.0 345.0 377.0 377.0 399.0 399.0 449.5 449.5 459.0 459.0 459.0 478.0 478.0 478.0 501.5 501.5 501.5 513.0 521.3 521.3 521.3 531.8 531.8 531.8 545.2 545.2 552.0 552.0 552.0 561.4 561.4 566.0 574.2 574.2 582.0 582.0 582.0 603.0 603.0 614.3 614.3 614.3 619.0 628.9 628.9 628.9 637.0 637.0 637.0 654.0 654.0 654.0 667.1 667.1

Setting Gap (x)20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 140 140 140 140 20 20 20 20 20 20 20 20 140 20 20 140 140 20 20 20 20 20 20 20 140 140 140 20 140 140 140 140 20 20 20 20 140

Weight (kg)3.0 3.5 3.2 4.7 4.7 4.8 4.8 4.7 7.4 7.1 6.2 11.6 10.7 10.8 14.4 16.3 14.0 14.8 16.5 16.1 17.6 22.4 25.7 32.7 35.0 37.0 30.9 32.6 35.2 41.4 37.9 39.8 41.2 37.9 39.6 43.6 36.7 38.9 35.5 37.7 41.6 45.7 41.2 40.8 45.9 48.9 41.1 45.6 45.7 38.7 43.4 42.2 57.6 50.9 51.0 53.7 55.8 52.6 49.0 53.0 52.2 42.9 52.5 50.1 50.5 58.2

50 PN10,16; 2" ANSI 150; 2" ADEF 60/65 PN10,16; 2.5" ANSI 150; 2.5" ADE 80 PN10,16" 80/100 PN10,16; 3" ANSI 150; 3"/4" ADE 80/100 PN10,16; 3" ANSI 150; 3"/4" ADE 100 PN10,16; 4" ANSI 150; 4" ADE DIMA INTERN 1882 150 PN10 100 PN10,16; 4" ANSI 150; 4" ADE 125/150 PN10,16; 5" ADE; 6" ANSI 150; 6"E 125/150 PN10,16; 5" ADE; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150; 6" E 200 PN10,16 200 PN10,16 8" ANSI 150 250 PN10,16 10" ANSI 150 250 PN10,16 10" ANSI 150 12" ANSI 150 300 PN10,16 300 PN16 300 PN10 12" ANSI 150 350 PN10 350 PN16 14" ANSI 150 350 PN10 350 PN16 14" ANSI 150 14" ANSI 150 350 PN10 350 PN16 14" ANSI 150 400 PN10 400 PN16 16" ANSI 150 400 PN10 400 PN16 400 PN10 400 PN16 16" ANSI 150 400 PN16 16" ANSI 150 16" ANSI 150 400 PN16 16" ANSI 150 450 PN10 450 PN16 18" ANSI 150 450 PN10 450 PN16 450 PN16 500 PN16 18" ANSI 150 18" ANSI 150 450 PN16 500 PN16 18" ANSI 150" 450 PN10 450 PN16 18" ANSI 150 500 PN10 500 PN16 20" ANSI 150 500 PN16 20" ANSI 150

1613 1614 1614 1615 1734 1759 1759 1759 1635 1633 1760 1758 1757 1757 1655 1655 1656 1656 1657 1657 1658 1658 1658 6002 6002 6002 1659 1659 1659 6035 1766 1766 1766 1767 1767 1767 1784 1784 1662 1662 1662 1768 1768 6036 1769 1769 6003 6003 6003 1770 1770 1771 1771 1771 6037 1772 6004 1772 6004 6004 6004 1773 1773 1773 1774 1774

20

Viking Johnson 1999


GPS

MaxiDaptor DN50/2" to DN600/24"Tolerance Min Max546.0 555.3 555.3 555.3 555.3 565.0 566.5 582.2 582.2 582.2 630.0 630.0 630.5 645.2 645.2 645.2 654.0 662.0 662.0 675.0 675.0 675.0 563.0 572.3 572.3 572.3 572.3 582.0 583.5 599.2 599.2 599.2 647.0 647.0 647.5 662.2 662.2 662.2 671.0 679.0 679.0 692.0 692.0 692.0

Viking JohnsonDimensions A1 B698 684 715 840 698 698 715 670 715 709 780 813 840 780 840 813 813 840 813 802 840 813 266 271 271 184 266 266 271 271 271 266 184 182 184 271 184 266 266 184 266 271 271 266

Flange Details

Gasket

Tee Bolts No. - Dia x Length10 - M12 x 290 10 - M12 x 290 10 - M12 x 290 10 - M12 x 205 10 - M12 x 290 10 - M12 x 290 10 - M12 x 290 10 - M12 x 290 10 - M12 x 290 10 - M12 x 290 10 - M12 x 205 10 - M12 x 205 10 - M12 x 205 10 - M12 x 290 10 - M12 x 205 10 - M12 x 290 10 - M12 x 290 10 - M12 x 205 10 - M12 x 290 10 - M12 x 290 10 - M12 x 290 10 - M12 x 290

A

C303 303 303 218 303 303 303 303 303 303 218 303 218 303 218 303 303 218 303 303 303 303

Setting Gap (x)140 140 140 20 140 140 140 140 140 140 20 20 20 140 20 140 140 20 140 140 140 140

Weight (kg)58.3 54.3 62.0 64.0 58.5 58.7 62.2 54.2 62.5 61.2 63.4 61.2 66.1 63.1 63.7 70.9 71.0 60.9 71.1 64.4 78.0 71.3

20" ANSI 150 500 PN10 500 PN16 600 PN16 20" ANSI 150 20" ANSI 150 500 PN16 500 PN10 500 PN16 20" ANSI 150 600 PN10 24" ANSI 150 600 PN16 600 PN10 600 PN16 24" ANSI 150 24" ANSI 150 600 PN16 24" ANSI 150 600 PN10 600 PN16 24" ANSI 150

6038 1775 1775 1775 1775 1776 1776 1777 1777 1777 1778 1778 1778 1779 1779 1779 6039 1780 1780 6005 6005 6005

673.0 682.3 682.3 682.3 682.3 692.0 693.5 709.2 709.2 709.2 757.0 757.0 757.5 772.2 772.2 772.2 781.0 789.0 789.0 802.0 802.0 802.0

Note: MaxiDaptor with 140mm setting gap have a stepped sleeve and therefore do not slide completely over the pipe end

AquaGrip Flange Adaptor DN225 to DN800Pipe O.D.225 225 225 250 250 250 250 250 250 280 280 280 315 315 315 315 315 315 315 315 355 355 355 355 355 355 355 355 355 355 355 355 355

SDR Rating11 17/17.6 26/33 11 11 17/17.6 17/17.6 26/33 26/33 11 17/17.6 26/33 11 11 11 17/17.6 17/17.6 21 26/33 26/33 11 11 11 11 11 17/17.6 17/17.6 17/17.6 21 21 26/33 26/33 26/33

Flange Details Nominal Specification200 200 200 200 250 200 250 200 250 250 250 250 250 300 300 250 300 300 250 300 300 300 350 350 400 300 300 350 300 350 300 350 350 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 10 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 10 PN 16 PN 10 PN 16 PN 16 PN 10 PN 16 PN 16 PN 16 PN 16 PN 16 PN 10 PN 16

No. of Clamp Bands2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2

GasketS1763 1685 1685 1685 1685 1686 1686 1686 1686 1686 1713 1687 1686 1686 1686 1687 1687 1687 1687 1687 1687 1687 1687 1687 1687 1688 1688 1688 1688 1688 1688 1688 1688

Clamp Dimensions Bolts A B C No. - Dia x Length4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M16 x 130 4 - M20 x 120 4 - M20 x 120 4 - M20 x 120 4 - M20 x 120 4 - M20 x 120 4 - M20 x 120 4 - M20 x 120 4 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 6 - M20 x 120 340 340 340 340 405 340 405 340 405 405 405 405 405 445 460 405 460 460 405 460 445 460 505 520 580 445 460 520 460 520 460 505 520 192 192 192 212 186 212 186 212 186 194 194 194 295 315 245 295 245 261 295 245 355 325 325 325 325 325 325 325 325 325 325 325 325 170 170 170 170 170 170 170 170 140 138 138 140 140 140 140 140 140 140 140 140 140

End Load Type MDPE HPPE1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Weight (kg)14.5 14.6 14.7 23.6 22.6 23.7 22.7 23.7 22.7 31.9 22.9 23.0 39.6 51.0 46.0 38.5 44.0 51.9 42.0 42.5 55.4 57.0 65.0 65.0 75.1 45.0 47.0 63.0 40.0 58.0 52.0 60.1 61.0

GPS

Dimension C is fixed for PN16 flanged version. For other configurations contact Viking Johnson for advice.Viking Johnson can manufacture Coupling products to virtually any diameter. Those shown are for information. For sizes or diameters not shown, please request further information.

21

Viking Johnson 1999


AquaGrip Flange Adaptor DN225 to DN800Pipe O.D.400 400 400 400 400 400 400 400 400 400 450 450 450 450 450 450 450 450 450 450 450 450 469 469 469 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 508 508 560 560 560 560 560 560 560 560 560 610 630 630 710 710 800

Viking JohnsonEnd Load Type MDPE HPPE1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 1 1 2 1 2 1 2 2

SDR Rating11 11 11 13.6 17/17.6 17/17.6 17/17.6 21 26/33 26/33 11 11 11 11 17/17.6 17/17.6 17/17.6 17/17.6 21 21 26/33 26/33 17/17.6 21 26/33 11 11 11 11 17/17.6 17/17.6 17/17.6 17/17.6 21 21 21 21 26/33 26/33 26/33 26/33 33 17/17.6 17/17.6 17/17.6 21 21 26/33 26/33 26/33 26/33 33 17/17.6 26/33 17/17.6 21 17/17.6 26

Flange Details Nominal Specification350 400 400 400 350 400 400 400 400 400 350 400 400 450 350 400 400 450 350 400 350 400 450 450 450 400 450 500 500 400 450 500 600 400 450 500 500 400 450 500 16 20 450 500 600 450 500 450 500 500 600 24 600 600 600 28 700 700 PN 16 PN 10 PN 16 PN 16 PN 16 PN 10 PN 16 PN 16 PN 10 PN 16 PN 16 PN 10 PN 16 PN 10 PN 16 PN 10 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 10 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 10 PN 16 PN 16 PN 16 PN 16 ANSI 150 ANSI 150 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 10 PN 16 PN 16 ANSI 150 PN 16 PN 16 PN 16 ANSI 150 PN 16 PN 6

No. of Clamp Bands3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5

Gasket1688 1688 1688 1689 1689 1689 1689 1689 1689 1689 1689 1689 1689 1689 1719 1719 1719 1719 1719 1719 1719 1719 1719 1719 1721 1719 1719 1719 1719 1721 1721 1719 1721 1721 1721 1721 1721 1721 1721 1721 1721 1721 1723 1723 1723 1723 1723 1723 1723 1723 1723 S1762 S1762 S1762 1795 S6029 S6028 S6026

Clamp Dimensions Bolts A B C No. - Dia x Length9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M20 x 120 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 9 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 130 12 - M24 x 150 12 - M24 x 150 12 - M24 x 150 12 - M27 x 150 12 - M27 x 150 15 - M27 x 150 15 - M27 x 150 520 565 580 580 520 565 580 580 565 580 520 565 580 615 520 565 580 640 520 580 520 580 640 640 640 580 640 670 715 580 640 715 840 580 640 670 715 580 640 715 597 698 640 715 840 640 715 640 670 715 840 813 840 840 840 927 910 860 345 345 345 345 345 345 345 345 345 345 432 369 411 369 432 411 411 411 432 411 432 411 511 411 411 432 411 432 411 432 411 411 411 432 411 411 432 432 411 411 432 432 502 432 432 502 432 502 432 432 432 542 449 449 536 569 565 565 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 135 155 155 155 155 155 155 155 155 155 155 155 155 155 155 155 155 155 225 225 225 225 225 225 225 225 220 220 220 220 270 270 335 335

Weight (kg)81.0 91.1 94.4 90.3 77.2 86.1 90.2 92.3 82.9 87.2 119.0 112.0 130.0 135.0 114.0 121.0 125.0 176.0 112.0 123.0 110.0 122.0 140.0 136.0 129.0 136.0 147.0 163.0 176.0 129.0 140.0 133.0 215.0 127.0 137.0 149.0 183.0 125.0 136.0 163.0 90.0 129.0 168.0 191.0 238.0 163.0 187.0 159.0 169.0 178.0 226.0 252.0 225.0 212.0 219.0 273.0 456.0 383.0

22

800

Dimension C is fixed for PN16 flanged version. For other configurations contact Viking Johnson for advice.Viking Johnson can manufacture Coupling products to virtually any diameter. Those shown are for information. For sizes or diameters not shown, please request further information.

Viking Johnson 1999


GPS

AquaGrip Flange Adaptor DN63 to DN180Pipe O.D.63 90 90 110 110 125 125 160 160 180 180

Viking JohnsonSetting Gap (x) Min Max10 10 10 10 10 10 10 10 10 10 10 30 30 30 30 30 30 30 30 30 30 30

SDR Rating11 11 17/17.6 11 17/17.6 11 17/17.6 11 17/17.6 11 17/17.6

Flange Details Nominal Specification50 / 65 / 80 80 80 100 100 100 100 150 150 150 150 PN10, 16 PN10, 16 PN10, 16 PN10, 16 PN10, 16 PN10, 16 PN10, 16 PN10, 16 PN10, 16 PN10, 16 PN10, 16

Gasket

No. of Gripper Segments10 14 14 17 17 19 19 24 24 26 26

Tee Bolts No. - Dia x Length Full Half1 2 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 8 - M12 x 110 8 - M12 x 110 8 - M12 x 110 8 - M12 x 110

A

Dimensions A1 B200 200 200 220 220 220 220 285 285 285 285 95 96 96 96 96 96 96 99 99

C118 118 118 118 118 118 118 124 124

Weight (kg)3.6 3.8 3.8 4.2 4.2 4.3 4.3 8.1 8.1 8.3 8.5

6001 1785 1785 1786 1786 1787 1787 1788 1788 1789 1789

126.0 167.5 167.5 188.0 188.0 203.0 203.0 240.0 240.0 257.5 257.5

101 124 101 124

FlexLock Flange Adaptors for SteelPipe O.D.60.3 76.1 88.9 114.3 165.1 168.3 219.1 219.1 219.1 273 273

Flange Details

Gasket

No. of Inserts

Stud Bolts A No.- Dia x Length2 - M12 x 110 2 - M12 x 110 4 - M12 x 110 4 - M12 x 115 8 - M12 x 115 8 - M12 x 115 8 - M12 x 115 12 - M12 x 115 8 - M12 x 115 12 - M16 x 125 12 - M16 x 125

Dimensions A1 B C T

Setting Gap (x) Min Max10 10 10 10 10 10 10 10 10 10 10 30 30 30 30 30 30 30 30 30 30 30

Weight Pressure (bar) (kg) Working Test

50 PN10,16; 2" ADE; 2" ANSI 125/150 60/65 PN10,16; 3" ADE; 3.5" AD; 3" ANSI 125/150 65 PN10,16; 80 PN6,10,16; 90 PN6; 3" ADE; 3.5" AD; 3" ANSI 125/150 100 PN10,16; 110 PN6,10,16; 4" ADE; 3.5"/4" ANSI 125/150 150 PN10,16; 6" E; 6" ANSI 125/150 150 PN10,16; 6" E; 6" ANSI 125/150 200 PN10; 8" E 200 PN16 8" ASA 150 250 PN10 250 PN16

1375 1394 1382 1367 1369 1369 1370 1370 1370 1737 1737

3 3 4 4 7 7 12 12 12 15 15

133.5 165 151.5 185 163.0 200 194.0 220 252.5 285 255.5 285 306.0 340 306.0 340 306.0 343 376.0 395 376.0 405

75 120 25 75 120 25 75 117 22 75 127 25 75 127 25 75 127 25 73 127 25 73 127 25 73 127 25 90 137 25 90 137 25

3.2 3.4 5.3 5.6 9.3 9.4 15.0 15.2 15.2 50.2 20.5

16 16 16 16 16 16 16 16 16 10 10

24 24 24 24 24 24 24 24 24 15 15

F l e x L o c k F l a n g e A d a p t o r s f o r M e t r i c D u c t i l e I ro nPipe O.D.77

Flange Details

Gasket No. of Inserts1690 3

Stud Bolts A No.- Dia x Length2 - M12 x 115 162.0

Dimensions A1 B C185 75 127

T25

Setting Gap Weight Pressure (bar) (x) (kg) Working Test Min Max10 30 3.7 16 24

60/65 PN10,16; 3 ADE; 2.5 ANSI 125/150 80 PN10,16; 3 ADE; 3 ANSI 125/150 100 PN10,16; 4 ADE; 3.5/4 ANSI 125/150 150 PN10,16; 6 E; 6 ANSI 125/150 DIMA INTERN 1882 - 150 PN10 200 PN10; 8 E 200 PN16 250 PN10 250 PN16

98

1630

4

4 - M12 x 115

181.0

200

75

127

25

10

30

4.8

16

24

118

1618 1369 1369 1631 1631 1737 1737

4 7 7 12 12 15 15

4 - M12 x 115 8 - M12 x 115 6 - M12 x 115 8 - M16 x 125 6 - M16 x 125 12 - M16 x 125 12 - M16 x 125

200.0 257.5 257.5 316.0 316.0 376.0 376.0

229 285 285 340 340 395 405

75 75 73 75 75 90 90

127 127 127 137 137 137 137

25 25 25 25 25 25 25

10 10 10 10 10 10 10

30 30 30 30 30 30 30

6.4 9.4 11.1 13.9 13.8 20.2 20.5

16 16 10 16 16 10 10

24 24 15 2 24 15 15

170 170 222 222 274 274

GPS

23


Viking Johnson 1999


QuickFit Flange AdaptorPipe NominalDN40/1.5" DN40/1.5" DN50/2" DN50 DN50 DN50/2" DN50/2" DN65/2.5" DN65/2.5" DN65/2.5" DN65/2.5" DN75 DN80/3" DN80/3" DN80/3" DN80/3" DN80/3" DN100/4" DN110 DN100/4" DN100/4 DN100/4" DN100/4" DN100/4" DN125 DN125/5" DN125/5" DN125/5" DN125/5" DN125/5" DN150/6" DN150/6" DN150/6" DN150/6" DN150/6" DN150/6" DN150/6" DN180 DN200 DN200/8" DN200/8" DN200/8" DN200/8" DN225 DN225 DN200/8" DN200/8" DN200/8" DN200/8" DN225/9 DN250 DN250

Viking JohnsonGasket Tee Dimensions Bolts A A1 B C T No. - Dia x Length2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 2 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 4 - M12 x 110 6 - M12 x 110 6 - M12 x 110 8 - M12 x 110 6 - M12 x 110 8 - M12 x 110 8 - M12 x 110 8 - M12 x 110 6 - M12 x 110 6 - M12 x 100 6 - M12 x 120 6 - M12 x 120 8 - M12 x 120 8 - M12 x 120 6 - M12 x 120 138.0 165 138.0 165 138.0 165 138.0 165 138.0 165 150.0 185 150.0 185 150.0 185 150.0 185 150.0 185 150.0 185 150.0 185 161.0 200 161.0 200 177.0 200 177.0 200 177.0 220 183.0 229 183.0 229 194.0 229 194.0 229 198.0 220 198.0 220 198.0 220 198.0 254 214.0 254 214.0 254 214.0 254 214.0 254 214.0 254 240.0 285 240.0 285 255.5 285 257.0 285 262.5 285 264.5 285 265.0 285 267.0 285 287.0 343 306.0 343 309.0 343 306.0 340 309.0 340 312.0 343 312.0 340 317.0 343 319.0 343 319.0 337 319.0 340 331.5 340 337.0 405 337.0 406 346.0 368 346.0 370 346.0 370 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 93 118 16 93 118 16 93 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 93 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 16 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 75 118 19 73 108 18 75 118 19 73 108 18 90 128 22 90 128 19 90 128 19 90 128 19 90 128 19

Pipe Type1.5" AC ISO 4200/2 Steel Steel, Imp PVC Metric PVC AWWA cl A CI Cl 25 AC Cast Iron ISO 4200/2 Steel ISO 4200/3 Steel API 5L Steel, Imp PVC Metric PVC Steel, Imp PVC Metric PVC Cast Iron AC Metric Ductile Iron ISO 4200/3 Steel Metric PVC Steel, Imp PVC Metric Ductile Iron Cast Iron AWWA Ductile Iron AWWA C209 PVC Metric PVC ISO 4200/2 Steel Steel Metric PVC Imp PVC Steel ISO 4200/3 Steel Metric PVC Steel BS DI ANSI DI/PVC BS CI ISO Steel Metric PVC Metric PVC Steel BS DI Steel BS DI Metric PVC Metric PVC ANSI DI/PVC BS CI BS CI BS CI Steel/PVC Metric PVC Metric PVC CI CI CI

Pipe O.D.57.0 57.0 60.3 63.0 63.5 69.0 69.1 70.0 73.0 73.0 76.1 75.0 88.9 90.0 96.0 96.0 98.0 108.0 110.0 114.3 118.0 122.0 122.0 122.0 125.0 133.0 139.7 140.0 140.2 141.3 159.0 160.0 168.3 170.0 175.3 177.3 177.8 180.0 200.0 219.1 222.0 219.1 222.0 225.0 225.0 230.0 232.0 232.0 232.0 244.5 250.0 250.0 259.0 259.0 259.0

Flange Details

Setting Gap (x)20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

Weight (kg)3.0 3.0 3.0 3.0 3.0 3.4 3.4 3.1 3.1 3.1 3.3 3.3 4.3 4.7 4.3 4.3 4.1 5.5 5.5 4.9 4.9 4.9 4.9 4.9 6.9 6.9 6.6 6.6 6.6 6.6 8.5 8.5 8.4 8.4 8.3 8.3 8.3 9.2 10.6 11.7 11.7 12.3 12.3 10.9 11.8 12.1 12.1 13.9 11.5 13.3 17.2 16.3 16.0 16.0 15.3

50 PN10,16,25,40; 2" ANSI 150; 2" ADE 50 PN10,16,25,40; 2" ANSI 150; 2" ADE 50 PN10,16,25,40; 2" ANSI 150; 2" ADE 50 PN10,16,25,40; 2" ANSI 150; 2" ADEF 50 PN10,16,25,40; 2" ANSI 150; 2" ADEF 65 PN10,16; 2" ANSI 150; 2.5"ADE 65 PN10,16; 2" ANSI 150; 2.5"ADE 65 PN10,16; 2.5" ANSI 150; 2.5"ADE 65 PN10,16; 2.5" ANSI 150; 2.5"ADE 65 PN10,16; 2.5" ANSI 150; 2.5"ADE 65 PN10,16; 2.5" ANSI 150 65 PN10,16; 2.5" ANSI 150 80 PN,10,16; 3" ANSI 150; 3" ADE 80 PN,10,16; 3" ANSI 150 80 PN,10,16; 3" ANSI 150; 3" ADE 80 PN,10,16; 3" ANSI 150; 3" ADE 80 PN,10,16; 3" ANSI 150; 4" ADE 100 PN10,16; 4" ANSI 150; 4" AD 100 PN10,16; 4" ANSI 150; 4" AD 100 PN10,16; 4" ANSI 150; 4" AD 100 PN10,16; 4" ANSI 150; 4" AD 100 PN10,16; 4" ADE 100 PN10,16; 4" ADE 100 PN10,16; 4" ADE 100 PN10,16; 4" ANSI 150; 4" ADE 125 PN10,16; 5" ADE 125 PN10,16; 5" ADE 125 PN10,16; 5" ADE 125 PN10,16; 5" ADE 125 PN10,16; 5" ADE 150 PN10,16; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150; 6" E 150 PN10,16; 6" ANSI 150 200 PN10; 8" ANSI 150; 8" E 200 PN10; 8" ANSI 150; 8" E 200 PN10; 8" ANSI 150; 8" E 200 PN16 200 PN16 200 PN10; 8" ANSI 150; 8" E 200 PN16 200 PN10; 8" ANSI 150; 8" E 200 PN10; 8" ANSI 150; 8" E 8 AD 200 PN16 200 PN16 250 PN16 250 PN10; 10" E 9" AD 225 PN10 225 PN16; 9" E

1599 1599 1500 1582 1582 1565 1565 1727 1727 1727 1560 1560 1501 1501 1406 1406 1406 1596 1561 1404 1404 1580 1580 1580 1580 1563 1503 1503 1503 1503 1559 1559 A1418 A1418 A1409 A1506 A1506 A1506 736* A1419 A1419 A1419 A1419 A1401 A1401 A1550 A1550 A1550 A1550 A1542 A1402 A1402 A1551 A1551 A1551

24

DN225/9" DN225/9" DN225/9"


Viking Johnson 1999


GPS

QuickFit Flange AdaptorPipe NominalDN225/9" DN250/10" DN250/10" DN250/10" DN250/10" DN280 DN250/10" DN250/10" DN250/10" DN250/10" DN315 DN315 DN300/12" DN300/12" DN300/12" DN300/12" DN300/12" DN300/12" DN300/12" DN300/12" CI Steel DI Steel DI Metric PVC ANSI DI/PVC/CI CI CI CI Metric PVC Metric PVC Steel DI BS CI cl AB ANSI DI/PVC/CI ANSI DI cl D BS CI cl CD BS CI cl CD BS CI cl CD

Viking JohnsonGasket Tee Bolts No. - Dia x Length6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 8 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 6 - M12 x 120 8 - M12 x 120 6 - M12 x 120 6 - M12 x 120

Pipe Type

Pipe O.D.259.0 273.0 274.0 273.0 274.0 280.0 282.0 286.0 286.0 286.0 315.0 315.0 323.9 326.0 333.8 335.3 343.0 345.0 345.0 345.0

Flange Details

A346.0 360.0 361.0 360.0 361.0 367.0 369.0 373.0 373.0 373.0 402.0 402.0 410.9 413.0 420.8 422.3 430.0 432.0 432.0 432.0

Dimensions A1 B C405 406 406 406 406 432 406 406 406 405 457 460 460 460 460 483 483 457 457 460 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128

T22 19 19 22 22 19 19 19 19 22 19 22 22 22 22 19 19 19 19 22

Setting Gap (x)20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

Weight (kg)17.2 16.0 16.0 17.8 17.8 16.3 18.5 18.5 16.6 16.3 20.9 20.6 21.4 21.4 19.5 20.1 20.0 20.9 20.9 18.4

250 PN16 250 PN10; 10" E 250 PN10; 10" E 250 PN16 250 PN16 250 PN16 10" ANSI 150 10" AD 250 PN10; 10" E 250 PN16 300 PN10; 12" D 300 PN16 300 PN16 300 PN16 300 PN16 12" ANSI 150; 12" E 12" ANSI 150; 12" E 12" A 300 PN10; 12" D 300 PN16

A1551 A1544 A1544 A1544 A1544 A1411 A1411 A1553 A1553 A1553 A1403 A1403 A1420 A1420 A1555 A1412 A1412 A1554 A1554 A1554

* denotes unfitted gasket The products previously marketed as MidiDaptor require different gaskets to those listed above. Please contact Viking Johnson Technical Department for further details.

L a rg e D i a m e t e r F l a n g e A d a p t o r s f o r P V C P i p e sPipe TypeMetric PVC Metric PVC Imp PVC Imp PVC Imp PVC Imp PVC Imp PVC IPS AWWA C900 Metric PVC Metric PVC Imp PVC Imp PVC Imp PVC Imp PVC IPS AWWA C900 Metric PVC Metric PVC Imp PVC Imp PVC Imp PVC Imp PVC Imp PVC IPS AWWA C900

Pipe O.D.355.0 355.0 355.6 355.6 355.6 355.6 355.6 355.6 388.0 400.0 400.0 406.4 406.4 406.4 406.4 406.4 442.0 450.0 450.0 457.0 457.0 457.0 457.0 457.0 457.0 495.0

Flange Details Nominal Specification350 350 350 350 350 14" 14" 14" 14" 400 400 400 400 400 16" 16" 16" 450 450 450 450 450 18" 18" 16" 18" PN10 PN16 PN10 PN16 PN25 TABLE DE TABLE F ANSI 150 ANSI 150 PN10 PN16 PN10 PN16 PN25 TABLE ADE ANSI 150 ANSI 150 PN10 PN16 PN10 PN16 PN25 TABLE AD TABLE E ANSI 150 ANSI 150

Gasket AJ51LS J51LS J51LS J51LS J51LS J51LS J51LS J51LS J52LS J53LS J53LS J53LS J53LS J53LS J53LS J53LS J55LS J55LS J55LS J55LS J55LS J55LS J55LS J55LS J55LS J57LS 442.0 442.0 442.5 442.5 442.5 442.5 442.5 442.5 475.0 487.0 487.0 493.5 493.5 493.5 493.5 493.5 529.0 537.0 537.0 544.0 544.0 544.0 544.0 544.0 544.0 582.0

Dimensions A1 B C505 520 505 520 555 527 553 533 533 565 580 565 580 620 578 597 597 615 640 615 640 670 641 641 597 635 91 91 91 91 98 91 91 91 91 91 91 91 91 98 91 91 91 96 96 96 96 98 96 96 96 96 148 148 148 148 155 148 155 155 153 155 155 148 148 155 148 155 155 153 153 153 153 155 153 153 155 155

T18 18 18 18 25 18 25 25 18 25 25 18 18 25 18 25 25 23 23 23 23 25 23 23 25 25

Setting Gap (x)25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

Flange Holes No. Diameter16 16 16 16 16 12 16 12 12 16 16 16 16 16 12 16 16 20 20 20 20 20 12 16 16 16 23 28 23 28 34 25 29 29 29 28 31 28 31 37 25 29 29 28 31 28 31 37 25 25 29 32

PCD460.0 470.0 460.0 470.0 490.0 470.0 495.0 476.0 476.0 515.0 525.0 515.0 525.0 550.0 520.5 540.0 540.0 565.0 585.0 565.0 585.0 670.0 584.0 584.0 540.0 578.0

Weight (kg)22.6 23.9 22.6 23.9 34.1 25.0 34.6 31.6 28.1 32.6 34.8 26.1 27.7 40.5 34.8 37.5 33.6 33.3 39.0 35.2 37.2 44.1 38.6 38.5 31.9 38.6

GPS

25


Viking Johnson 1999


Large Diameter Flange Adaptors for PVC PipePipe Type Pipe O.D

Date post:	16-Jul-2015
Category:	Documents
Upload:	samarakoon-banda
View:	470 times
Download:	4 times

VJ Coupling Data

Documents