Date post: | 25-Jan-2017 |
Category: |
Technology |
Upload: | michael-ofili |
View: | 270 times |
Download: | 8 times |
Contents
Drive Test summary
Analysis on coverage data
Page 2
23/5/1 page3
DT 、 CQT
OMC
NO YES
Monitor the performance Analyze the data Order a scheme
Carry out scheme
Proving the scheme
Complain
It is important to take a DT and CQT in the network
DT and CQT
Test tools introduction
Page 4
Z750 ( phone )Support HSDPA/UMTS
Support EDGE/GPRS/GSM
Support HSDPA 3.6Mbps
Support R99 PS 384kbps
HUAWEI M30 ( data card )Support HSUPA/HSDPA/UMTS
Support EDGE/GPRS/GSM
Support HSDPA 7.2Mbps
Support HSUPA 2Mbps
Test tools introduction
Page 5
CPICH RSCP CPICH Ec/Io Pilot Path Count BLER Tx power Neighbours Throughput Log
Coverage Analysis Overshooting Analysis
Pilot Pollution Analysis
Neighbours Analysis
Call drop Analysis
Delay Analysis
Network KPI Analysis
DT introduction
Page 6
The aim of the test is to acquire the coverage data by the single base
station, cluster and the whole network as related to service on CS,
PS. Including signal strength indicator Ec, signal quality instruction
Ec/Io, service establish success rate, handover success rate,, call
drop rate, UL/DL average throughput rate, service establish delay and
so on, all of them are used to investigate the signal quality which is
covering network. Thus testing if the single station work is normal or
not, investigate the worse regional of performance in the network,
such as hardware issue, pilot pollution, cell level or system parameter
issue.
CQT Introduction
Page 7
CQT :call quality test it is a fixed-point test, the main purpose is acquisition of data for the indoor
and outdoor, where is the signal quality, service establish, maintain and so on.
the aim of the test is to confirm if local signal quality is good or not, the
performance of service establishing and maintaining, it used to research the
issue on the network, especially optimized network issue in indoor and
outdoor, interference, wireless communication environment issue such as
complex and so on. The survey key is radio link signal quality, multipath
effect, service establish performance, cell level throughput rate and so on, but
it is also important to survey the performance of handover, and the Signal leak
Page 8
outline
Drive Test summary
Analyze the data about coverage
Analyze the data about service
Overshooting
23/5/1 page9
Some of the pilot signal are strong, it covers the area more than the planning
area, it make a discontinuous dominant pilot cell in other cell areaSite is too high, it is not reasonable on antenna engineering parameters,
streets effect, etc
Overshooting
23/5/1 page10
overshootingSolution
23/5/1 page11
Adjust the antenna for azimuth and tilt.
Modified the parameter
Add the CPICH power
Adjust base station distribution, and reduce the height of the tower
Page 12
Pilot Pollution Analysis
Receive signal are similar strong or weak, but there are no main pilot cell 。
Receive signal It is usually having a enough good pilot signal, but all of them are having weak Ec/Io .
Most of the equipment support 3 maximum number active set on WCDMA, if the similarity Ec/Io number is more than 3, so it is as to be a interference for three active set.
Reason: overshooting, distribute the site on circle, street effect, strong reflection and so on, these are result of signal distortion
Pilot Pollution analysis
23/5/1page13
Pilot Pollution Analysis
23/5/1 page14
solution:
make a main pilot service cell, and obtain a stronger signal than other neighbour
Adjust the antenna azimuth and tilt.
Modify the parameter, CPICH power.
Adjust base station distribution, add a strong signal cell in pilot pollution area
Page 15
Missing Neighbour
Neighbours are likely to join in active set of cells, its is possible to make a reselection or handover with other cells,
When the phone is stay in DCH state, it will send the neighbour information by the RNC of managing measure, it is managing mobile phone to measure all of receiving neighbour signal, if it is missing nieghbour, it will result in drop call due to handover failure.
When the mobile phone stays in idle and FACH state, the phone must obtain the neighbour information from system message, and measure the neighbour which meet the requirements, if it is missing nieghbour, it will result in reselecting not in time or call setup failure;
23/5/1 page16