+ All Categories
Home > Documents > €¦ · Web viewAGENDA Members Meeting & Exchange November 15-16, 2017 Stambaugh Auditorium 1000...

€¦ · Web viewAGENDA Members Meeting & Exchange November 15-16, 2017 Stambaugh Auditorium 1000...

Date post: 07-Jan-2020
Category:
Upload: others
View: 0 times
Download: 0 times
Share this document with a friend
4
AGENDA Members Meeting & Exchange November 15-16, 2017 Stambaugh Auditorium 1000 5 th Avenue Youngstown, OH Wednesday, November 15 7:00 – 8:00 am Registration 8:00 – 8:15 am Welcome & Opening Remarks Rob Gorham, NCDMM/America Makes 8:15 – 9:00 am Operating in the New Reality; Public-Private Partnerships (Keynote Speaker) 9:00 – 10:00 am Coordinating Insights through the America Makes Digital Storefront John Wilczynski and Joe Veranese, NCDMM/America Makes 10:00 – 10:30 am Break & Networking 10:30 – 11:00 am Convening Standardization Bodies – The Additive Manufacturing Standards Collaborative Jim McCabe, ANSI and Jim Williams, All Points Additive 11:00 – 11:30am Additive Manufacturing Leadership Open Forum 11:30 – 12:00pm Award Presentation 12:00 – 1:00 pm Lunch Break & Networking 1:00 – 1:45 pm Engage and Establish a Workforce for the Future Vicki Thompson, America Makes 1:45 – 2:00 pm SME Announcement 2:00 – 2:30 pm 4060: The Living Textbook Dhruv Bhate, Phoenix Analysis and Design Technologies, Inc. (PADT) Howard Kuhn, University of Pittsburgh 2:30 – 3:00 pm Break & Networking 3:00 – 4:00 pm Additive Manufacturing as a Transformative Technology Panel Ralph Resnick, NCDMM/America Makes 4:00 – 4:15 pm Summary and Closing Remarks Rob Gorham, NCDMM/America Makes
Transcript
Page 1: €¦ · Web viewAGENDA Members Meeting & Exchange November 15-16, 2017 Stambaugh Auditorium 1000 5th Avenue Youngstown, OH Wednesday, November 15 7:00 – 8:00 amRegistration 8:00

AGENDAMembers Meeting & Exchange

November 15-16, 2017Stambaugh Auditorium

1000 5th AvenueYoungstown, OH

Wednesday, November 15

7:00 – 8:00 am Registration

8:00 – 8:15 am Welcome & Opening RemarksRob Gorham, NCDMM/America Makes

8:15 – 9:00 am Operating in the New Reality; Public-Private Partnerships (Keynote Speaker)

9:00 – 10:00 am Coordinating Insights through the America Makes Digital StorefrontJohn Wilczynski and Joe Veranese, NCDMM/America Makes

10:00 – 10:30 am Break & Networking

10:30 – 11:00 am Convening Standardization Bodies – The Additive Manufacturing Standards CollaborativeJim McCabe, ANSI and Jim Williams, All Points Additive

11:00 – 11:30am Additive Manufacturing Leadership Open Forum

11:30 – 12:00pm Award Presentation

12:00 – 1:00 pm Lunch Break & Networking

1:00 – 1:45 pm Engage and Establish a Workforce for the FutureVicki Thompson, America Makes

1:45 – 2:00 pm SME Announcement

2:00 – 2:30 pm 4060: The Living TextbookDhruv Bhate, Phoenix Analysis and Design Technologies, Inc. (PADT)Howard Kuhn, University of Pittsburgh

2:30 – 3:00 pm Break & Networking

3:00 – 4:00 pm Additive Manufacturing as a Transformative Technology PanelRalph Resnick, NCDMM/America Makes

4:00 – 4:15 pm Summary and Closing RemarksRob Gorham, NCDMM/America Makes

4:15 – 5:00 pm Governance Board Meeting (America Makes Members Only)

5:00 – 7:00 pm Evening Reception - OPEN TO ALL ATTENDEES

Page 2: €¦ · Web viewAGENDA Members Meeting & Exchange November 15-16, 2017 Stambaugh Auditorium 1000 5th Avenue Youngstown, OH Wednesday, November 15 7:00 – 8:00 amRegistration 8:00

Thursday, November 16

7:00 – 8:00 am Registration

8:00 – 8:15 am Opening RemarksRob Gorham, NCDMM/America Makes

8:15 – 9:00 am 3000 Maturation of Advanced Manufacturing for Low Cost SustainmentSteve Szaruga, UDRI and Brett Conner, YSU

9:00 – 9:45 am 4043 Non-Destructive Evaluation of Complex Metallic Additive Manufactured StructuresRoger Spencer, EWI

9:45 – 10:30 am 4051 A Flexible Adaptive Open Architecture to Enable a Robust Third-Party Ecosystem for Metal Powder Bed Fusion Additive Manufacturing Systems Bill Carter and Michael Mahony, GE Research Center

10:30 – 11:00 am Break & Networking

11:00 – 11:45 am 4055 A Low Cost Industrial Multi3D Systems for 3D Electronics ManufacturingDavid Espalin, UTEP

11:45 – 12:30 pm 4049 Economic Production of Next Generation Orthopedic Materials through Powder Reuse in Additive ManufacturingSteven Schmid, University of Notre Dame

12:30 – 1:30 pm Lunch Break & Networking

1:30 – 2:00 pm America Makes New Project Call – Industry Day

2:00 – 2:30 pm Special Announcements

2:30 – 3:00 pm 3006 MAMLS Phase 2, Low Cost Sustainment: Bell Crank Brett Conner, Youngtown State University

3:00 – 3:30 pm Break & Networking

3:30 – 4:00 pm 3007 MAMLS Phase 2, Low Cost Sustainment: Oil Cooler Adam Hicks, University of Dayton Research Institute

4:00 – 4:30 pm 3008 MAMLS Phase 2, Low Cost Sustainment: FairingsDavid Sundquist, Boeing

4:30 – 4:45 pm Closing Remarks Rob Gorham, NCDMM/America Makes


Recommended