AGENDAMembers Meeting & Exchange
November 15-16, 2017Stambaugh Auditorium
1000 5th AvenueYoungstown, OH
Wednesday, November 15
7:00 – 8:00 am Registration
8:00 – 8:15 am Welcome & Opening RemarksRob Gorham, NCDMM/America Makes
8:15 – 9:00 am Operating in the New Reality; Public-Private Partnerships (Keynote Speaker)
9:00 – 10:00 am Coordinating Insights through the America Makes Digital StorefrontJohn Wilczynski and Joe Veranese, NCDMM/America Makes
10:00 – 10:30 am Break & Networking
10:30 – 11:00 am Convening Standardization Bodies – The Additive Manufacturing Standards CollaborativeJim McCabe, ANSI and Jim Williams, All Points Additive
11:00 – 11:30am Additive Manufacturing Leadership Open Forum
11:30 – 12:00pm Award Presentation
12:00 – 1:00 pm Lunch Break & Networking
1:00 – 1:45 pm Engage and Establish a Workforce for the FutureVicki Thompson, America Makes
1:45 – 2:00 pm SME Announcement
2:00 – 2:30 pm 4060: The Living TextbookDhruv Bhate, Phoenix Analysis and Design Technologies, Inc. (PADT)Howard Kuhn, University of Pittsburgh
2:30 – 3:00 pm Break & Networking
3:00 – 4:00 pm Additive Manufacturing as a Transformative Technology PanelRalph Resnick, NCDMM/America Makes
4:00 – 4:15 pm Summary and Closing RemarksRob Gorham, NCDMM/America Makes
4:15 – 5:00 pm Governance Board Meeting (America Makes Members Only)
5:00 – 7:00 pm Evening Reception - OPEN TO ALL ATTENDEES
Thursday, November 16
7:00 – 8:00 am Registration
8:00 – 8:15 am Opening RemarksRob Gorham, NCDMM/America Makes
8:15 – 9:00 am 3000 Maturation of Advanced Manufacturing for Low Cost SustainmentSteve Szaruga, UDRI and Brett Conner, YSU
9:00 – 9:45 am 4043 Non-Destructive Evaluation of Complex Metallic Additive Manufactured StructuresRoger Spencer, EWI
9:45 – 10:30 am 4051 A Flexible Adaptive Open Architecture to Enable a Robust Third-Party Ecosystem for Metal Powder Bed Fusion Additive Manufacturing Systems Bill Carter and Michael Mahony, GE Research Center
10:30 – 11:00 am Break & Networking
11:00 – 11:45 am 4055 A Low Cost Industrial Multi3D Systems for 3D Electronics ManufacturingDavid Espalin, UTEP
11:45 – 12:30 pm 4049 Economic Production of Next Generation Orthopedic Materials through Powder Reuse in Additive ManufacturingSteven Schmid, University of Notre Dame
12:30 – 1:30 pm Lunch Break & Networking
1:30 – 2:00 pm America Makes New Project Call – Industry Day
2:00 – 2:30 pm Special Announcements
2:30 – 3:00 pm 3006 MAMLS Phase 2, Low Cost Sustainment: Bell Crank Brett Conner, Youngtown State University
3:00 – 3:30 pm Break & Networking
3:30 – 4:00 pm 3007 MAMLS Phase 2, Low Cost Sustainment: Oil Cooler Adam Hicks, University of Dayton Research Institute
4:00 – 4:30 pm 3008 MAMLS Phase 2, Low Cost Sustainment: FairingsDavid Sundquist, Boeing
4:30 – 4:45 pm Closing Remarks Rob Gorham, NCDMM/America Makes
