WJ150-18003PlyCorrugatedCardboard ProductionLine · SHANGHAIUPGINTERNATIONALTRADINGCO.,LTD 1...

SHANGHAI UPG INTERNATIONAL TRADING CO., LTD

1

WJ 150-1800 3 Ply Corrugated Cardboard

Production Line（Design speed:150m/min）

Add: Room 2403 Jincheng Mansion 511 Tianmuxi Road, 200070 P.R.ChinaTEL：86-21-63177436 FAX：86-21-63538343Email: [email protected]

mailto:[email protected]


2

Introduction：1. Design Speed: 150m/min2. Economic Speed: 120m/min3. Working Width：1800mm4.Production Line Length ： About 60 meters （ Exact length basis ongroundwork drawing）P.S. The real paper in production speed test should meet the followingrequirement:*Reel paper minimum degree: B degree* Percentage of moisture for real paper 11% ± 1%* Tissue paper 150~200g/m2

* Liner paper 150~200g/m2

* Flute paper 105~180g/m2

5. Flute profiles：A、C、B、E Flute（Or according to the customers` requirement）6. Steam requirement：quantity2500－3200Kg/Hr Max pressure 1.3MpaCommon pressure 0.98－1.12MPa

7. Power supply:380V 50Hz Three phase four wire system8. Total power：About 200kw Common power：About 150 kw9. Equipment size：60m×10m×4.5m（L×W×H）10. Equipment flowing direction：According to the user’s factory to fix right or

left.

Note: Customer’s self-provided parts1. Steam system：2000Kg/Hr Steam boiler 1 set Pressure:0.98－1.3MPaPipes above equipment valve and back gas drain pipes.2. Air compressor, pipes and glue pipes.3. Power, wire link to operation box and its pipes.4. Water source, water feeding pipes and buckets.5. Water, electricity and air installation on groundwork.6. Testing material: real paper, corn (Tuberous crop) starch, sodium hydroxidefor industry and borax, etc.7. Motor oil, lube, hydraulic oil and grease lubricant and high temperaturegrease lubricant.8. Board and lodging for installation and commissioning personnel and arrangeworkers to cooperate installation.

Performance：RS-1500H Hydraulic Shaft less Mill Roll Stand


3

Technical Parameter:Stand move mode Full hydraulic actionWorking width Max 1600mm Min 800mmPaper diameter Max￠1500mm Min￠350mmSingle Load Max 3000kgStand main bearing diameter ￠210mmAir working pressure（MPa） 0.6～0.9MPaTotal power 5.5kwWorking power Pressure，380V Frequency，50HzDimension 3850×1600×1650（L×W×H）

Hydraulic system parameter：Working pressure（MPa） 12～16 MPaHydraulic pump working span(swing) ￠100mm×460mmHydraulic pump diameter (clamption) ￠63mm×770mmHydraulic station motor power 5.5kw，Continuous workHydraulic station electro magnetismworking pressure

220V 50Hz

Characteristic：· Symmetry structure could install two bundles real paper at the same time,

and change the paper without any stop.· Adopt hydraulic drive that could make the real paper lift-lower, clamp and

release and move.· Adopt pneumatic strain to adjust the real paper.· Expanding clips design.· Tension control by pneumatic brake system, manual controlled and also

can be controlled by splicer.Raw materials and bought in parts：


4

· Stand main bearing adopts high quality thick-walled seamless steel pipe.Origin: Chengdu

· Two side wall plates and arms adopt: HT200 casting Origin: Hebei· Main beam like channel steel: 280mm Origin: An steel· Bearing：made in Ha, Wa , Luo .· Electrical device：made in Chint, ZheJiiang.· Pneumatic component: Airtac, Zaozhuang Origin: Taiwan, Shandong· Hydraulic：Beiye Group(Huade) Origin: BeiJiing, Zaozhuang, Shandong

Railing for Reels

Technical parameter：· The application of line width ：1800mm· Dimension：6000mm×400mm×300mm(L×W×H)Characteristic：· Push the real paper to the right position, handiness and agility.· Track buried and main frame welded by 16 channel steel, sturdy and

durable· The steel plates above the scene welded after the installation.· Match two dollies to install the paper from two sides.Raw materials and bought in parts：· The track and dolly materials：Tang steel, Ji Steel production profiles· Bearing: Made in Ha, Wa, Luo

SH-900DPre-heater

Technical Parameter:


5

Working width 1800mmPre-heater Roll Diameter ￠900mmAngle adjustment range 60~220 degreeSteam temperature 150～200℃Steam consumption 0.25t/hSteam pressure 0.8～1.3MPaWorking power 380V,50HzTotal power 0.55kwDimension（L×W×H） 3600mm×1200mm×900mm

Characteristic:· The surface of the rolls are polished and plated with chrome.· Electro motion adjust of the dimension of per-heater, and the range of

adjustment:60-220 degree· Per-heater rolls professional manufactured, consistent with national safety

standards for pressure vessels.· Pre-heater roller and paper guide roll are plated.· Electro motion adjust of the dimension of per-heater， suit for different

paper and speed.

Raw materials and bought in parts:· Both sides of panel material：HT250 casting Origin：Hebei· Guide paper roller material： 20 # steel Origin：Bao steel· Pre-heater roll material ： 20Gsteel ， Wall thickness 20mm

Origin：Ji steel· Main bearings：Made in Ha, Wa, Luo with seat bearing made in Jinrun,

Zhejiang.· Steam rotary tie-in, Metal hose：made in Luguan, Shandong.· Adjust motor ： 0.55kw Decelerate rate1 ： 100 made in Zhejiang

short-term work· Electricity device：Made in Chint, Zhejiang

SF-320S Single Facer


6

Technical Parameter:Working width Max.1850mm, min.900mmMax speed 150m/minWorking pressure 0.6-0.9Mpasteam work pressure 0.8-1.3MpaSteam consumption 0.65-1t/hTemperature requirements 160-200℃Machine power 33.95kwWorking power 380V, 50HzDimension 3200mm2400mm2300mm

Products characteristics :· Cardboard transmitting method adopts wind absorption, and keep flute

profiles stable under the running condition of high speed.· The wind machine absorbs corrugated paper to corrugated rollers through

vacuum box and form corrugated profile.· The width of wind groove of lower roller is not exceeding 2.5mm,and will

less fringe marks of single corrugated paperboard.· Transmission part adopt gimbal transmission, away from vibration source,

and make the transmission more steady and reliable, and easy tomaintain.

· The speed reducing box is oil-lubricating, close gear transmission, and willreduce machine vibration.

· Glue unit adopts auto-supply glue circularly, pneumatically reset and hasbuffering effect.

· Glue area will be electrically adjusted, glue unit can be runningindependently when machine steppes, and prevent glue running out.

· Upper corrugated roller surface are treated by special mesh snicked andchrome plated.

· Glue unit independent drive, pump-draw style, easy maintain and clean.· Corrugated forming unit is designed with small independent wall plate. The

roller is easy to disassembly, maintain, and quickly change flute profiles.· Upper-lower corrugated roller are made of high quality 48CrMo alloy steel,

and after heat-treatment, the rigidity is HRC 55-62, the surface are grindedand plated chrome.

· Flute profiles:A flute height 4.7mm B flute height 2.75mm E fluteheight 3.75mm（the flute profiles can be made according to client`s requirements）

Parameter of main parts:· Upper-lower corrugated roller are made of high quality 48CrMo alloy steel,

and after heat-treatment, the rigidity is HRC 56-60, the surface are grinded


7

and plated chrome.· Upper corrugated roller: ￠320mm lower corrugated roller: ￠320mm

Origin: Beijing· Pressure roller: ￠ 328mm, #45seamless steel pipe with quenching

treatment· Applicator glue roller: ￠250mm 45# seamless seel pipe, from Chengdu· surface are treated by special mesh snicked and chrome plated· Doctor glue roller: ￠140mm, 20# seamless seel pipe, from Chengdu· Pre-heating roller : ￠ 400mm 20G steel from Ji Steel Wall

thickness:20mm

Raw materials and bought in standard parts:· Wall plate two sides and seat: HT250 Origin : Hebei· The seat materials of transmitting unit: welded with channel steel· Rotary joints, metal soft tube: Lu guan qiu Shandong· Bearings：(mainly)NSK Japan;· Common bearing: Wa, Ha, Luo, bearing with seat: Jinrun,Zhejiang

(Chinese best product)· Engines: Main engine: 22kw 1set continues working· Wind absorption machine: 11kw 1set continues working· Glue unit self-running engine:0.75kw 1 set Chengbang, Taiwan Short

time work· Glue width-adjusting engine: 0.1kw 2sets Chengbang, made in

Taiwan Short time work· Electric appliances: Chint, China Pneumatic parts: Airtac, Taiwan

BS－T single layers bridge

Technical Parameter:Working width 1800mmMax speed 150m/min


8

Dimension 33200mm×4530mm×3160mmGuiding paper roller Upper, front ￠135mm

Upper, behind ￠135mmSlow transmitting paper roller active roller￠135mm

passive roller￠135mmtension roller￠85mmhang roller￠100mm

absorption transmitting paper roller ￠100mmElectricity 380V 50 HzTotal Power 8.1kw

Characteristic:· Exactly transmitting single facer corrugated cardboard to strain-tighten set

or wind absorption set through transmitting belt, for next process use.· Adopting wind absorption strain-tighten set, 3 KW high-voltage centrifugal

fan vacuum adsorption strain set, electro motion correct deflection, tomake sure cardboard stick tightly and level off.

· Electric control install two groups of operation plate, upper and lowerbridge can be adjusted arbitrarily.

· On paper-receiving unit, adopt independent conversion driver, transmit thesingle corrugated cardboard across the bridge and keep enoughcardboard quantity on bridge to meet the changing production speed,pre-heated by multi pre-heater, and stick through gluing machine anddouble facer.

· Equipped upward paper carrier, and two groups of transmitting beltconveyors, the transmitting speed is slowly, so as to form wave-likestacking, and to store corrugated cardboard.

Raw materials and bought in parts:· Channel steel of main bridge：# 20 steel Origin: An Steel· Paper-receiving unit transmitting belt: Nylon industry belt.· Paper storage unit transmitting belt: Parallel transmitting belt· Guiding paper engine( conversion control）： 4.0 kw 1 set continuous work

Origin Wuxi· Absorption tension engine: 3.0 kw 1 set continuous work Origin

Wuxi· Paper width adjustment engine: 0.55 kw 2 sets short time work Origin:

Hengshui· Bearings: Wa, Ha, Luo bearing with seat : Jinrun, Zhejing.· Electric appliances: Chinti Zhejiang

MH-900Triplex Pre-heater


9

Technical Parameter:Working width 1800mmPre-heater Roll Diameter ￠900mmAngle adjustment range 60~220 degreeSteam temperature 150～200℃Steam consumption 0.35～0.45t/hSteam pressure 0.8～1.3MPaTotal power 1.1kwElectricity pressure 380V, 50HzDimension （L×W×H） 3200mm×1200mm×1800mm

Characteristic:· Each roller surface is well whetted and chrome plated sooth and durable.· Electro motion adjust the dimension of pre-heater, the range of adjustment:

60-220 °· The pre-heating roller is made according to national container safety

standard· Pre-heating roller and guiding paper roller are eclectically galvanized· Electro motion adjust the dimension of pre-heater, suitable with different

grades of paper and machinery speed

Raw materials and bought in parts:· Both sides of panel material：HT250casting Origin：Hebei· Guide paper roller material： 20 # steel Origin：Bao steel· Pre-heating roller: 20G steel wall thickness: 20mm Origin: Ji Steel· Main bearings: Wa, Ha, Luo, the bearing with seat is from Jinrun, Zhejiang· Steam rotary tie-in:Johnson· Metal soft pipe: Luguanqiu, Shandong· Water valves: Beijing


10

· Adjustment engine： speed reducing ratio: 1： 100 short time working,Origin Zhejiang

· Electrical appliances: Chint

GL-288D Gluing machine

Technical Parameter：Working width 1800mmMax speed 150mm/minTemperature required 150~200℃Steam pressure 1.12～1.3MPaSteam consumption 0.1~0.15MPaCompressed air 0.6～0.9MPaTotal power 2.3kwElectricity 380V 50HzDimension ( Lx W x H ) 3500mm×1280mm×2100mmPressing paper method pressure roller stylePre-heating roller diameter：325mm

Guiding paper roller diameter：120mm

Applicator glue roller diameter：288mm

Dividing glue roller diameter：120mm

wall thickness 20 whetted andchrome platedwall thickness 15 whetted andchrome platedwall thickness 30 whetted andchrome platedwall thickness 15 whetted andchrome plated

Characteristic:· Independent engine transmitting, conversion control· Applicator roller surface are treated by mesh snicked and chrome plated.· Doctor roller and presser roller are well whetted and plated chrome.


11

· Pressure paper unit of pressure roller is pneumatic, flexible and convenientto operate

· Auto-circulating supply glue, so as to prevent the glue deposited.· Adopting pre-heating set, so as to avoid glue burnted.· All raw materials of pre-heating roller, applicator roller, dividing glue roller

is from Chengdu seamless steel pipe factory.

Raw materials and bought-in parts:· Wall plate two sides: HT250casting Origin: Hebei· Bearings: from Ha, Wa, Luo· Electrical appliances: Chint, Zhejiang,· Pneumatic parts: Airtac Origin Taiwan

DF-745 Double facer system (including driving unit)

Technical Parameter：Working width 1800mmMax. machinery speed 150m/minWorking speed 120-130m/minTemperature required 160～200℃Steam pressure 0.8～1.3MPaSteam consumption 1.2～1.8t/hCompressed air pressure 0.6～0.9MPaHeating plate length 8400mm(600mm×14)cooling section length 5000mmTotal power 60.5kwElectricity 380V 50HzDimension( L x W x H ) 15720mm×2300mm×1950 mm


12

Heating plate unit:Material 20G steel, Ji SteelProcess technique surface is whettedJoin method single cross typeTemperature method many groups controlledPressure method adopting dense pressure roller stylePressure roller diameter ￠60mm solid 45# steel. Origin Shou SteelSupporting roller diameter ￠60mm solid 45# steel Origin Shou SteelDimension ( L x W x H ) 1990mm×600mm×135mm

Driving Unit and Feeding Unit:1) Main transmitting roller diameter: upper￠745mm lower￠745mm2) big, small belt front passive roller diameter：￠320mm 20# steel, Origin:

Chengdu3) big, small belt correcting deflection roller diameter: 145mm 20# steel,

Origin: Chengdu4) Front, back supporting roller diameter:￠120mm 20# steel, Origin:

Chengdu5) Manual tension roller diameter: ￠120mm 20# steel, Origin: Chengdu6) Hydraulic tension roller diameter: ￠145mm 20# steel, Origin: Chengdu7) Cotton belt：Fuli, Shenyang8) Driving unit main engine：adjustment engine45kwCharacteristics:1) Whole body is high strength channel steel, stable, beautiful, suitable for

high speed machinery running.2) Heating plate is made according to national container safety standard, of

600mm steel. Inside, S type construction will raise the steam usageefficiency. More welded rods will keep heating plate unchanged in shape.

3) Heating section is tense pressure roller structure, cardboard sticks firmlyand levels off.

4) Steam pipes enter mouth, drainage mouth is S type, heating platetemperature is balanced and evenly.

5) Heating plate’s temperature is different in different section, suitable todifferent machinery speed.

6) Heating section pressure roller is hydraulic lifting whole body, stable,safety and reliable.

7) The upper canvas strap is equipped electro motion or manual deflectionadjusting set, one pneumatic strain set, one manual strain set. The lowercanvas is equipped strain and left-right adjustment set.

8) Drive unit adopts wearable, mesh rubber of big diameter, less belt skip,and raise stability when machinery running


13

9) Independent speed reducing box, less noise, roller diameter￠745mmadopts seal oil lubricating gears.

Raw materials and bought-in parts:1) Heating section main beam：280# channel steel Origin: An Steel2) Cooling section main beam：250# channel steel Origin: An Steel3) Hydraulic station: Beiye Group(Huade) Origin: Beijing, Zaozhuang,

Shandong4) Cotton belt: Origin: Fuli Shenyang5) Driving unit wall plates two sides: 20# Steel Origin: Hebei6) Rotary join tie-in, metal tube steam: Johnson, Luguanqiu, Shandong.7) Bearings: Ha, Wa, Luo, the bearing with seat is from Jinrun, Zhejiang8) Electric appliances: Chint, Zhejiang

SS-150P Thin blade Slitter Scorer

Technical specification:Design speed 150m/minMax. slitting width 1800mmMin. slitting width 120mm5 blades 8 scores the whole machine can move left-right ±

90mmDimension 3450×1450×2380Total power 7.55kwElectricity 380V 50HzWorking pressure 0.6~0.9 MpaComparative moisture 20％～90％Temperature required 5～50℃

Structure characteristic:1) Conversion adjustment speed can automatically follow production speed,


14

and keep in-phase2) In the process of production, auto- grinding edge system can be still

working while machine stops, and can set the interval meter and thegrinding time at any time according to the material and condition of hem.

3) 1mm high quality blade slits cardboard in high speed, slitting line is smooth,beautiful, unchanged shape, and good for printing

Main bought-in parts, raw materials and origin:1) Mail wall plate two sides: Q235A2) Slitting motor（frequency control）： 4kw 1 set continuous work3) Scorer motor： 3kw 1 set continuous work4) Horizontal movement motor: 0.55kw 1 set continuous work5) Blade: Diameter 200mm Materials: rigid alloy steel6) Bears are from Wa, Ha, Luo cities7) Electric appliances: Chint, China8) Pneumatic cylinder, pneumatic parts: Tianyuan, Airtac, Origin: Shandong,

Taiwan

NC-150N NC Cutting machine

Technical specification:Work width 1800mmMax machine speed 150m/minCutting length 500mm-9999mmCardboard original paper: ＜360g

liner paper ＜ 200g/thickness3 －14mmmoisture content ＜10％min. width warping1000mm ＜

30mm


15

Comparative moisture 20％～90％ Temperature required：5～50℃

Working pressure 0.6~0.9 MpaCutting cardboard blade shaftdiameter

upper￠ 188 mmlow￠ 188 mm

Guiding cardboard shaft diameter Front upper ￠165mm(sun wheel)Front lower ￠135mmBack upper ￠165mm(sun wheel)Back lower ￠135mm

Electricity 380V，50Hz ，80ATotal power 34.4kwMachine dimension 3400×1000×2100

Structure characteristic:1) Special structure design, high tensile strength wall plate and seat, there

are watching window on wall plate two sides, convenient and easy tomaintain.

2) Transmitting system adopts oil pump auto-cycling lubricating, make suretransmitting precision.

3) Adopting high precision, high rigidity whetted gears, bearing high runningand durable, make sure blade-edge joggle exactly, cardboard is level offand clean

4) High precision shaft, blade carrier design, cutting stably when machinehigh speed running

5) Special changing blade structure, quickly and easily changing blade6) The system is made according to C.E. standard, and has been strictly

tested by industry computer. The quality, life, and stability can beguaranteed.

7) Driving unit adopts A.C. Servo drive, quickly and exactly acts.8) Special electricity structure design, more saving electricity, can avoid the

problems of not stable electricity.9) Adopts special power bring and storage type design, save electric and

could overcome electric voltage not steady environment.10) System has self test function, can prevent machine loss because of

abnormal usage and false operation11) Computer automatically adjusts cutting speed according to cardboard

specifications and production speed, automatically follow cardboardrunning speed, assure in –phase.

12) Computer reserves 999 groups of order, and auto-complete based on theprogram and preferential condition, the screen display various productionmessage.

13) Cutting length: 500~9999mm，cutting precision :±1mm。14) Rotary blade is made in Tainwan


16

15) Shaft bearings are from NSK, Japan, suitable for machine high speedrunning, durable.

Main bought-in parts, raw materials and origin:1) Wall plates two sides and seat: HT250 casting Origin: Hebei, China2) Upper lower shaft: 45# steel3) Balde:W18crv5Co5（high speed tool steel）4) Gear: 40Cr whetted, quenched and tempered5) Main drive engine(a.c. servo)power: 30kw 1set Origin: China6) Transmitting cardboard engine power:3.7kw 1set Origin: Hengshui7) Oil pump engine power: 0.37kw 2set Origin: Zhejiang8) Computer control system, Computer system made in Taiwan.9) Bearing: (main)NSK Japan (common) Wa, Ha, Luo10) (bearing with seat) Deyuan, Fujian11) Electric appliances: Chint, China12) Pneumatic parts: Airtac Taiwan, Tianyuan Shandong

CF-100T Feeding machine

Technical Parameter：Stacking length Max.2300mmPneumatic pressure 0.6～0.9MPaElectricity 380V，50HzPower 10.8KwDimension （L x W x H） 10200mm×2400mm×1500mmCharacteristics：1) Automatic stacking and collecting of cardboard.2) Motorized transverse output.3) Transmitted with broad belt for vertical stacking.4) Switch control of the paperboard to specified height and number.Raw materials and bought-in parts：1) Belt transmitting engine：2.2 kw 3sets continuous work origin: Deyi Jiangsu2) Horizontal row paper engine: 4.0kw 1set not continuous work origin:

Deyi Jiangsu


17

3) Move baffle engine: 0.2 kw 1sets continuous work origin: Deyi Jiangsu4) Transmitting belt: industrial belt, Weite Tianjin5) Main channel steel: 16# steel6) Electric appliances: Chint Zhejiang7) Bearings: Wa, Ha, Luo Bearing with seat: Deyuan,Fujian

GF-T Glue making system

Technical Parameter：1) horizontal agitator：main body barrel volume 1300L 1set2) Carrying body barrel volume 500L 1set3) Store barrel volume in glue making shop： 1000L 1set4) Single facer store barrel volume： 350L 1set5) Single facer back- glue barrel volume： 350L 1set6) Secondary glue machine store barrel volume： 350L 1set7) Secondary glue machine back- glue barrel volume：350L 1set8) Electricity：voltage 380V frequency 50Hz current 25A9) Machine total power：12.15kwCharacteristic：1) Providing starch adhesive for single facer and gluing machine, etc.2) Horizontal glue making machine can produce main body glue and carrying

body glue, and mix and stir, the glue making quantity is large.3) In glue making shop, glue inside store barrel will be sent to store barrel of

every using glue machine, and supply their glue.4) store5) Store barrel, supply glue barrel have stir device, to avoid glue deposit.6) The glue making system are including carrying body barrel, main body

barrel, store barrel, and glue supplying pump, and back- glue pump, etc.7) The glue making system adopts auto-cycling supply glue, extra glue will

follow back back-glue barrel. The glue level will be auto-controlled, theglue inside back-glue barrel will be sent back to store barrel of using gluemachine, cyclically supply glue, to save glue and prevent glue burned anddeposited.

8) After work finished, the extra glue of each using glue machine will bedrawn to store barrel of glue shop by pump, for next time usage.


18

9) Responsible technical guide and advising adhesive agent formulationRaw material and bought-in parts：1) Horizontal agitator：main body barrel engine power 5.5 kw 1set continuous

work from Wuxi2) Carrying body barrel engine power 1.5kw 1set continuous work from Wuxi3) Glue making shop store barrel engine power: 0.75kw 1set continuous work

from Wuxi4) Main gluing feeding pumps engine power: 2.2kw 2sets not continuous

work from Hengshui5) Glue making shop and barrels, pipes, etc should be provided by client, the

pipe diameter is 2〝zinc galvanized6) Bearing: Ha, Wa, Luo7) Ball valves, tee, elbow, moving connects, in-side and outside joints are of

high qualified products in China8) Electric appliances: Chint Zhejiang

GF－T Pneumatic system

Technical Parameter：Working pressure 0.8-1.0MPaEnvironment temperature -5℃----＋50℃Compressed air output 0.9/minStore barrel volume 1.5m3Working electricity 380V， 50HzSystem total power 7.5kw intermittent work

Characteristic：1) To provide compressed air for whole production line, and keep working

pressure stable. Compressed air station supply compressed air, pressureis stable and quantity is enough.

2) The air will be filtered in the station, to keep air clean and stable.3) Each air-using machine will get air through main pipeline, independently


19

control and not affecting with other.4) Each air-using machine will adjust air pressure according to actual

requirement, equipped with pressure monitor dial plate.5) The pipelines with machinery will be made of copper or high quality of PVC

pipe, reliable and durable.6) Before the compressed air enter into the air-using machine, second filter

and oil-frog treatment will be required, so as to make sure relative partsnormal and safety used.

7) Combines pneumatic system and electric control system into one body,operate them together.

Raw material and bought-in parts：1) Air compressor: 7.5kw2) Store barrel materials: 20# steel Ji Steel, thickness: 20mm pressure

container is made according to pressure container safety standard.3) Proportional valves, pressure adjustment valves, pressure meter, air 3 set

unit, electromagnetic valves, filtering device, made in Yadeke Taiwan

EF-T Electric control system

Technical Parameter：Working power：380V 50Hz 300AControl electricity pressure：220V 50Hz 30ACharacteristic：1) Whole production line will be completely controlled, while main line is

including single facer group, double facer, slitter, cutoff.2) The comprehensive usage of pneumatic control, pneumatic control,

electric control, to make sure the advance of whole production line control.3) Each machine are designed to have two systems, independent control and

cross point control, can meet the need of each machine independentlyworks, and of the working together with other machines.

4) There is caution system among machines, so as to coordinate the work ofeach operator.

5) Each operation desk can correctly show the working speed of othermachine.

6) B、C machine and double facer have speed indicating device.7) Regular low voltage electric appliances Zhengtai


20

SP-S Steam system

Technical parameters：Steam consumption 1.2-1.8t/hBoiler 2T/hBoiler pressure 13MPaTemperature inside pipes 160－200℃Steam pressure 0.8－1.3MPaSingle facer enter steam pipe diameter：￠48mmDrainage steam pipe diameter: ￠32mmPre-heater enter steam pipe diameter：￠48mmDrainage steam pipe diameter ￠32mmDuplex-heater enter steam pipe diameter：￠48mmDrainage steam pipe diameter ￠32mmDrainage steam pipe diameter ￠32mmBaker and finalizing enter steam pipe diameter：￠48mmDrainage steam pipe diameter ￠32mmCharacteristic：1) Supplying steam for whole production line and steam using machine, keep

working temperature stable.2) Each machine has independent small steam system, five section control

temperature, save resource, easily adjust.3) Control working temperature can be completed by adjusting steam

pressure, and equipped pressure monitoring dial plate.4) Each drainage water unit has side way to drain air, the machine will

become cooling very soon when it stopped.5) Floating ball supply water device, 1/2 metal soft pipe and ball valves

connect with side way, plunger valve.6) Pipeline system connects with rotary heating parts by metal soft pipes, so

as to expand the usage life of rotary joints.7) All steam pipelines are of seamless steel pipes, make sure safety usage

under high pressure.8) All steam pipelines surface are painted with rusty-preventing paint, brush

sliver-power.

Date post:	27-Jun-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

WJ150-18003PlyCorrugatedCardboard ProductionLine · SHANGHAIUPGINTERNATIONALTRADINGCO.,LTD 1...

Documents