PA 1508 Part 2 Issue 1 Rev 0 Page 1 of 20
WSAA PRODUCT APPRAISAL CERTIFICATE
REHAU Pty Ltd - REHAU AWASHAFT DN 250/300 Polypropylene (PP) Terminal Maintenance Shafts, AWADUCT Polypropylene (PP) pipes and fittings, AWADUCT flex connect pipe coupler and AWADOCK Polypropylene (PP) fittings
REHAU AWASHAFT DN 250/300 Polypropylene (PP) Terminal Maintenance Shafts, AWADUCT (PP) pipes and fittings, AWADUCT flex connect pipe coupler and AWADOCK (PP) fittings, have been appraised for compliance with the requirements of WSA 137:2013, AS/NZS 5065:2005, AS/NZS 4327:1995 and WMTS-055:2016 and WSAA Product Specifications WSA PS 341, WSA PS 240 and WSA PS 235 as listed in the attached Schedules A & B.
Product Category Polypropylene (PP) Terminal Maintenance Shafts, pipes, fittings and flex-connect pipe coupler
PA Number: PA 1508 Part 2 (Certificate)
Supplier REHAU Pty Ltd
Brand REHAU AWASHAFT, AWADUCT and AWDOCK
Standards WSA 137:2013 Industry Standard for Maintenance Shafts and Maintenance Chambers for Sewerage
AS/NZS 5065 - Polyethylene and polypropylene pipes and fittings for drainage and sewerage applications
WMTS-055:2016 - Plastic fittings – Connectors with flexible intermediate joints for drainage and sewerage applications
AS/NZS 4327:1995 - Metal-banded flexible couplings for low-pressure applications
WSAA Product Specifications
WSA PS-341 Maintenance Shafts (MS) – Polypropylene (PP) for Non-Pressure Applications – Gravity Sewerage
WSA PS 240 Polypropylene (PP), Ribbed Construction, Pipe and Fittings for Non-Pressure Applications – Sewerage
WSA PS-235 Couplings, Metal-Banded Flexible, for Non-Pressure Applications - Sewerage
Other Specifications
Not Applicable
Issue date 18 April 2018
Expiry date 18 April 2023
PA 1508 Part 2 Issue 1 Rev 0 Page 2 of 20
Recommendations It is recommended that WSAA members and associates, subject to any specific requirements, accept / authorise the REHAU:
a) AWASHAFT DN 250/300 Polypropylene (PP) sewer Terminal Maintenance
Shaft (TMS) assemblies;
b) AWADUCT Polypropylene pipes and fittings;
c) AWADOCK Polypropylene fittings; and
d) AWADUCT ‘Flex connect’ pipe coupler
as listed in Schedule B provided pipeline design, installation, acceptance
testing and commissioning in accordance with applicable WSAA Codes and the
manufacturer’s requirements where specified.
Disclaimer The disclaimer on Page 3 explains a number of very important limits on your ability to rely on the information in this Product Appraisal Certificate (Certificate) and the assessment criteria used to underlay it. Please read it carefully and take it into account when considering the content in this Certificate.
PA 1508 Part 2 Issue 1 Rev 0 Page 3 of 20
1. Disclaimer
This Product Appraisal Certificate (Certificate) is issued by WSAA on the understanding that:
This Certificate applies to the product(s) as submitted in Schedule A. Any changes to the product(s) either minor or major shall void this Certificate.
To maintain the recommendations of this Certificate any such changes shall be detailed and notified to the Product Appraisal Manager for consideration and review of the Certificate including the product appraisal criteria underlying it and appropriate action. Appraisals and their recommendations will be the subject of continuous review dependent upon the satisfactory performance of products.
WSAA reserves the right to undertake random audits of product manufacture and installation. Where products fail to maintain appraised performance requirements the appraisal and its recommendations may be modified and reissued. Certificates will be reviewed and reissued at regular intervals not exceeding five (5) years.
WSAA reserves the right to withdraw this Certificate at any time in its sole and absolute discretion for any reason.
The following information explains a number of very important limits on your ability to rely on the information in this Certificate. Please read it carefully and take it into account when considering the contents of this Certificate.
Any enquiries regarding this Certificate should be directed to the Product Appraisal Manager Phone: 03 8605 7601 email [email protected].
1.1. Issue of Certificate
This Certificate has been published and/or prepared by WSAA and nominated Project Manager and peer group of technical specialists (the Publishers).
The Certificate and the underlying product appraisal criteria have been prepared for use within Australia only by technical specialists that have expertise in the function of products such as those appraised in the Certificate (the Recipients).
By accepting this Certificate, the Recipient acknowledges and represents to the Publisher(s) and each person involved in the preparation of the Certificate and product appraisal criteria underlying it that the Recipient has understood and accepted the terms of this Disclaimer.
1.2. Limits on Reliance on Information and Recommendations
1.2.1. Disclaimer of liability
Neither the Publisher(s) nor any person involved in the preparation of the Certificate and product appraisal criteria underlying it accept(s) any liability for any loss or damage suffered by any person however caused (including negligence or the omission by any person to do anything) relating in any way to the Certificate or the product appraisal criteria underlying it. This includes (without limitation) any liability for any recommendation or information in the Certificate or any errors or omissions.
1.2.2. Intellectual Property and other rights
WSAA does not undertake any assessment of whether the importation, manufacture, sale or use of the Product the subject of this Certificate infringes the intellectual property rights or proprietary rights of any person. Recipients of the Certificate should undertake their own assessment of whether (as relevant) the importation, manufacture, sale or use of the relevant Products infringe the intellectual property rights or other proprietary rights of any person. If the Product infringes intellectual property rights or other proprietary rights there is potential for the supply of the Products to be interrupted.
From time to time WSAA and the other Publishers may receive notice of allegations that the importation, manufacture, sale or use of the Product infringes intellectual property rights or other proprietary rights. WSAA's policy is to not refer to such allegations in its Certificate or take any other steps to put Recipients on notice of such allegations. If, however, WSAA becomes aware that the allegations have been admitted or proved in Court, then WSAA may, at its discretion, take such steps as it considers appropriate. As such, Recipients acknowledge, agree and accept that WSAA may have information in its possession about intellectual property rights infringement allegations or other infringement allegations in relation to the Product which are not referred to or disclosed in this Certificate and which are not otherwise communicated to Recipients.
1.2.3. Need for independent assessment
The information and any recommendation contained (expressly or by implication) in this Certificate are provided in good faith (and subject to the limitations noted in this Certificate). However, you should treat the information as indicative only. You should not rely on that information or any such recommendation except to the extent that you reach an agreement to the contrary with the Publisher(s).
This Certificate does not contain all information that a person might require for the purposes of assessing any product discussed or appraised within it. The product appraisal criteria used in preparing this Certificate may not address all relevant aspects of the Product.
Recipients should seek independent evidence of any matter which is material to their decisions in connection with an assessment of the Product and consult their own advisers for any technical information required. Any decision to use the Product should take into account the reliability of that independent evidence obtained by the Recipient regarding the Product. Recipients should also independently verify and assess the appropriateness of any recommendation in the Certificate, especially given that any recommendation will not take into account a Recipient’s particular needs or circumstances.
WSAA has not evaluated the extent of the product liability and professional indemnify insurance that the provider of the product maintains. Recipients should ensure that they evaluate the allocation of liability for product defects and any professional advice obtained in relation to the product or its specification including the requirements for product liability and professional indemnity insurance.
1.3. No Updating
Neither the Publisher(s) nor any person involved in the preparation of this Certificate or the product appraisal criteria underlying it [has] [have] any obligation to notify you of any change in the information contained in this Certificate or of any new information concerning the Publisher(s) or the Product or any other matter.
1.4. No Warranty
The Publisher(s) do[es] not, in any way, warrant that steps have been taken to verify or audit the accuracy or completeness of the information in this Certificate, or the accuracy, completeness or reasonableness of any recommendation in this Certificate.
PA 1508 Part 2 Issue 1 Rev 0 Page 4 of 20
SCHEDULE A
APPENDIX A - PRODUCT CERTIFICATIONS
Copies of the following Quality and Product Certificates are available for downloading from the WSAA ‘Members Only’ project portal website.
SCHEDULE A1 - REHAU – QUALITY MANAGEMENT SYSTEMS
Business Location: REHAU AG + Co, Rheniumhaus Otto-Hahn-Str. 2, D-95111 Rehau, GERMANY
There are 30 more locations of administration offices and plants included in this certification as detailed in the attachment.
Quality Systems Standard ISO 9001:2008
Certificate Registration no. 01 104 0101700
Certifying agency TÜV Rheinland Cert GmbH
First date of certification NA
Current date of certification 29 June 2015
Expiry date of certification 28 June 2018
SCHEDULE A2 - M.O.L – QUALITY MANAGEMENT SYSTEMS
Business Location: M.O.L Gummiverarbeitung GmbH & Co. KG, GutenbergstraBe 12 – 14, 49377 Vechta,
GERMANY
Quality Systems Standard ISO 9001:2015
Certificate Registration no. 496810 QM15
Certifying agency DQS UL Management Systems Solutions
First date of certification 20 March 2017
Current date of certification 20 March 2017
Expiry date of certification 30 January 2020
NOTE: DQS UL Management Systems Solutions is accredited by DAkkS Deutsche Akkreditierungsstelle
SCHEDULE A3 - M.O.L – DECLARATION OF PERFORMANCE According to Declaration (EU) No. 305/2011
Business Location: M.O.L Gummiverarbeitung GmbH & Co. KG, GutenbergstraBe 12 – 14, 49377 Vechta,
GERMANY
Product Standard/Spec. EN 681-1:2002
Certificate Registration no. BL-001-2013
Certifying agency M.O.L Gummiverarbeitung GmbH & Co. KG
First date of certification NA
Current date of certification 12 July 2013
Expiry date of certification NA
PA 1508 Part 2 Issue 1 Rev 0 Page 5 of 20
SCHEDULE A
SCHEDULE A4 - BOREALIS GROUP – QUALITY MANAGEMENT SYSTEMS
A total 18 sites belongs to Borealis Group in Germany, Belgium, Hungary, Italy, Romania, Serbia, Sweden, Finland, Slovakia and Austria is included in this certification.
Quality Systems Standard ISO 9001:2008
Certificate Registration no. A160304
Certifying agency International Certification Management GmbH
First date of certification NA
Current date of certification 28 February 2016
Expiry date of certification 14 September 2018
NOTE: DQS UL Management Systems Solutions is accredited by DAkkS (Deutsche Akkreditierungsstelle)
SCHEDULE A5 - REHAU PTY LTD – PRODUCT CERTIFICATION
Business location: Suite 1.02, Level 1, Quad 1, 8 Parkview Drive, Sydney Olympic Park NSW 2127
Product Standard AS/NZS 5065:2005 Polyethylene and polypropylene pipes and fittings
for drainage and sewerage applications
Confirmation No. ISO Type 5 Certification AMI 71503
Issuing certification body ApprovalMark International
First date of certification 25 January 2018
Current date of certification 25 January 2018
Expiry date of certification 25 January 2023
SCHEDULE A6 - REHAU AG & CO – PRODUCT CERTIFICATION
Business location: lm Kalbertale 1, D07819, Triptis, GERMANY 127
Product Standard AS/NZS 4327:1995 Metal-banded flexible couplings for low-pressure
applications
Confirmation No. ISO Type 5 Certification AMI 74764
Issuing certification body ApprovalMark International
First date of certification 23 March 2018
Current date of certification 23 March 2018
Expiry date of certification 23 March 2019
PA 1508 Part 2 Issue 1 Rev 0 Page 6 of 20
SCHEDULE B
TABLE B1 - AWASHAFT DN 250/300 PP TMS PRODUCT SCHEDULE
Product Supplier Picture
AWASHAFT PP TMS DN 315/250 elbow
REHAU
AWASHAFT PP TMS DN 250/250 elbow
REHAU
AWASHAFT PP TMS DN 250/160 elbow
REHAU
AWADUCT PP offset reducers:
DN 315/250
DN 250/200
DN 200/160
DN 160/110
REHAU
PA 1508 Part 2 Issue 1 Rev 0 Page 7 of 20
SCHEDULE B
Product Supplier Picture
AWADUCT PP DN 160 Ball joint – continuously adjustable up to +/- 7.5o horizontally or vertically with EPDM sealing rings (Safety-Lock)
(this item is included in this appraisal)
REHAU
AWADUCT PP DN 250 Vario double socket coupler – continuously adjustable up to +/- 7.5o horizontally or vertically with EPDM sealing rings (Safety-Lock)
(this item is included in this appraisal)
REHAU
Elastomeric seal for below components:
a) DN/OD 300 lip sealing ring for connection to riser
b) DN/OD 250 lip sealing ring for connection to riser
c) DN/OD 250 / 200 / 160 / 110 lip sealing ring for inlet/outlet
d) DN/OD 300 / 250 / 200 /160 lip sealing ring for reducer
MOL
Extension pipe or riser DN 300 or DN 225 PVC-U DWV SN8 to AS/NZS 1260
Installer
Injection moulded DN 300 or DN 225 PVC-U SWJ push on cap to AS/NZS 1260
Installer
PA 1508 Part 2 Issue 1 Rev 0 Page 8 of 20
SCHEDULE B
Product Supplier Picture
Injection moulded DN 300 or DN 225 PVC-U solvent weld on cap with screw lid and RR seal to AS/NZS 1260
Installer
PE Shroud Pipe (450mm dia minimum) to AS/NZS 4130, Concrete Surround and Surface Fittings (DI access cover to AS 3996 Class B or D)
Installer
REHAU AWASHAFT PP sewer DN 250/315 TMS can be connected to the inlet of DN/OD 110, 160, 200 and 250 using AWADUCT PP offset reducers.
The complete range of REHAU AWASHAFT DN 250/315 TMS assembly is:
Product Riser Size
(DN/OD)
Reducers
(DN/OD)
Connecting Pipe Size (DN/OD)
AWASHAFT TMS DN/OD 315 DN/OD 250 315 315/250
250/200
200/160
160/110
110
160
200
250
AWASHAFT TMS DN/OD 250 DN/OD 250 250 250/200
200/160
160/110
110
160
200
250
AWASHAFT TMS DN/OD 250 DN/OD 160 250 160/110
110
160
PA 1508 Part 2 Issue 1 Rev 0 Page 9 of 20
SCHEDULE B
FIGURE B1 - SCHEMATIC DIAGRAM AND COMPONENTS OF AWASHAFT DN 250/315
PP TMS ASSEMBLY
PA 1508 Part 2 Issue 1 Rev 0 Page 10 of 20
TABLE B3 - AWASHAFT PP DN250/300 TERMINAL MAINTENANCE SHAFT COMPONENTS
ApprovalMark ISO Type 5 Product Certification to AS/NZS 5065:2005, Licence No. AMI 71503
Item Model ID Model Name Product Description Size range Pic Application
AWASHAFT sewer TMS assembly Terminal Maintenance Shaft components
End of a property connection to sewer to allow insertion of equipment for inspection and maintenance different sizes of pipes to TMS
1 AWADUCT PP KGR PP (dia/dia)
Reducer
160/110, 200/160, 250/200 and 315/250
Reducers
Connection of different sizes of pipes to TMS
2 AWADUCT PP KGMM PP (dia) KGMM double socket coupler
AWADUCT PP double socket coupler
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
250 and 315
Double socket coupler
Used as part of TMS assembly
3 AWADUCT PP KGB PP (dia/angle)
KGB elbow
AWADUCT PP elbow
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
250/88° and 315/87°
Elbow
Used as part of TMS assembly
PA 1508 Part 2 Issue 1 Rev 0 Page 11 of 20
SCHEDULE B
TABLE B4 - AWADUCT PP PIPES AND FITTINGS
ApprovalMark ISO Type 5 Product Certification to AS/NZS 5065:2005, Licence No. AMI 71503
Item Model ID Model Name Product Description Size range Pic Application
1 AWADUCT PP KGEM PP SN10 (pipe dia/length)
KGEM pipes SN10 with socket coupler
AWADUCT SN10 pipe with socket coupler
and EPDM sealing rings according to DIN EN 1852 and AS/NZS 5065
Material: RAU- PP 2300
Colour: orange
110, 125, 160, 200, 250, 315, 400, 500, 630
(L = 1, 3 & 6m)
Wastewater pipes with RRJ.
Can be used to supplement maintenance chambers i.e internal drops.
2 AWADUCT PP KGGL PP SN10 (pipe dia/length)
KGGL pipes SN10 Fusion plain ended
AWADUCT SN110 FUSION plain-ended, according to DIN 1852 and AS/NZS 5065
Material: RAU-PP 2300
Colour: orange
110, 125, 160, 200, 250, 315, 400, 500, 630 (pipe length is not specified)
DN 800
(L = 3m & 6m)
Wastewater pipes utilising electrofusion jointing
Can be used to supplement maintenance chambers i.e internal drops.
This product is suitable for installation without rubber ring joint connection to network pipes
3 AWADUCT PP KGR PP (dia/dia) KGR reducers
AWADUCT PP reducer
with EPDM sealing ring
Material: RAU-PP 2300
Colour: orange
125/110; 160/110; 160/125; 200/160; 250/200; 315/250; 400/315; 500/400; 630/500
Reducers
Cconnection of different sizes of pipes to maintenance chamber base.
4 AWADUCT PP KGU PP (dia) KGU sleeve coupler
AWADUCT PP sleeve coupler
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
110; 125; 160; 200; 250; 315; 400; 500; 630
Sleeve coupler
Connection of the pipes to bases of MS, MC and MH
PA 1508 Part 2 Issue 1 Rev 0 Page 12 of 20
SCHEDULE B
Item Model ID Model Name Product Description Size range Pic Application
5 AWADUCT PP KGMM PP (dia) KGMM double socket coupler
AWADUCT PP double socket coupler
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
110; 125; 160; 200; 250;315; 400; 500; 630
Double socket coupler
Connection of the pipes to bases of MS, MC and MH
6 AWADUCT PP KGB PP (dia/angle)
KGB elbow
AWADUCT PP elbow
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
110, 125, 160, 200, 250, 315, 500, 630, 800
(15°, 30°, 45°, 88°)
Elbow
Connection of pipes to bases where required (according to water agency guidelines)
Inspection elbow utilised in internal drops.
7 AWADUCT PP Ball joint (dia) (Soc-Soc & Soc-Spi)
Ball joint
AWADUCT PP ball joint
Infinite angle adjustment by ± 7.5º horizontally or vertically
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
160 Soc-Soc,
160 Soc-Spi,
200 Soc-Soc,
200 Soc-Spi
Ball joint
Flexible connection to achieve the angle (up to 7.5 in any direction) between pipe and base on site druing installation.
8 AWADUCT PP KGMM PP Vario (dia)
KGMM Vario double socket coupler
Infinite angle adjustment by ± 7.5º horizontally or vertically
With EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
250 & 315
KGMM vario
Flexible connection to achieve the angle (up to 7.5 in any direction) between pipe and base on site during installation.
PA 1508 Part 2 Issue 1 Rev 0 Page 13 of 20
SCHEDULE B
Item Model ID Model Name Product Description Size range Pic Application
9 AWADUCT PP KGM PP (dia) KGM socket plug
AWADUCT PP socket plug
Material: RAU-PP 2300
Colour: orange
110; 125; 160; 200; 250; 315; 400; 500; 630; 800
Socket plugs
Blockts the unused inlets
10 AWADUCT PP KGEA PP (dia/dia/angle 45° or 88°)
KGEA single branch 45° and 88°
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
110/110/45° to 630/630/45°
and
160/110/88° to 630/630/88°
Single branch
Connection to MS risers
11 AWADUCT PP KGUS PP (dia) KGUS adaptor
KGUS adaptor from vitrified clay spigot end to plastic
with EPDM sealing rings
Material: RAU-PP 2300
Colour: orange
110, 125, 160
Adaptor from vitrified clay spigot end to plastic at the connection to base.
PA 1508 Part 2 Issue 1 Rev 0 Page 14 of 20
SCHEDULE B
TABLE B5 - AWADOCK PP FITTINGS
ApprovalMark ISO Type 5 Product Certification to AS/NZS 5065:2005, Licence No. AMI 71503
Item Model ID Model Name Product Description Size range Pic Application
12.1
AWADOCK KG-KG
KG-KG PP (dia/dia)
AWADOCK, connection to sewer pipes
DN160/200 made of PP, PE, PVC to smooth- walled polymer pipes and GRP pipes
Infinite angle adjustment by ± 7.5º horizontally or vertically
Material: PP/EPDM/Q-TE-C
Colour: Orange/Grey/Black
200/160, 250/160, 315/160, 400/160, 500/160& 250/200, 315/200, 400/200, 500/200
Connection to sewer pipes
DN160/200 made of PP, PE, PVC to smooth- walled polymer pipes and GRP pipes
Suitable for connection to MS risers instead of using a single branch
12.2 AWADOCK KG-KG
KG-KG PP (dia-dia/dia)
AWADOCK, connection to sewer pipes
DN160/200 made of PP, PE, PVC to smooth- walled polymer pipes and GRP pipes
Infinite angle adjustment by ± 7.5º horizontally or vertically
Material: PP/EPDM/Q-TE-C
Colour: Orange/Grey/Black
630-700/160,
700-900/160,
900-1400/160 &
630-700/200,
700-900/200,
900-1400/200
Same as above
12.3 AWADOCK KG KG concrete / Vitrified clay with ball joint (dia, type)
AWADOCK with ball joint, connection of sewer pipes DN160/200 made from PVC and PP to concrete, reinforced concrete or vitrified clay pipes.
Infinite angle adjustment by ± 7.5º horizontally or vertically
Material: SBR/Q-TE-C/PP
Colour: Black/Green
Standard DN160 & DN200
Types: K, A, B, C, D
Connection of sewer pipes DN160/200 made from PVC and PP to concrete, reinforced concrete or vitrified clay
With Ball joint
PA 1508 Part 2 Issue 1 Rev 0 Page 15 of 20
SCHEDULE B
Item Model ID Model Name Product Description Size range Pic Application
12.4 AWADOCK KG KG concrete/Vitrified clay (dia, type)
AWADOCK without ball joint, connection of sewer pipes DN160 made from PVC and PP to concrete, reinforced concrete or vitrified clay pipes.
Material: SBR/Q-TE-C/PP
Colour: Black/Green
Standard DN160
Types: K, A, B, C, D
Same as above
Without ball joint and only for DN160.
12.5 AWADOCK KG KG to thick-walled reinforced concrete pipes (dia, type)
AWADOCK, connection of sewer pipes DN160/200 made from PVC and PP to thick-walled and multi-layer reinforced concrete pipes according to DIN1916
Consisting of a connecting seal, adjusted to wall thickness, a screw crown designed as a pipe duct, a concave chamfered AWADUCT PP connecting pipe
Material: SBR/Q-TE-C/PP
Colour: Black/Green
DN160 & DN200
Types E, F, G, H, D
Connection of sewer pipes DN160/200 made from PVC and PP to thick walled and multi layer reinforced concrete
Similar to 12.3
without ball joint and for thick walled and multi layer reinforced concrete.
12.6 AWADOCK KG KG to thick-walled reinforced concrete pipes (dia, type)
AWADOCK, connection of sewer pipes DN150 made from vitrified clay to concrete, reinforced concrete or vitrified clay pipes
Material: SBR/Q-TE-C/PP
Colour: Black/Green
DN/OD150
Types: K, A, B, C
Connection of sewer pipes DN150 made from vitrified clay to concrete, reinforced concrete or vitrified clay pipes
Same as 12.4 for connection of DN150 vitrified clay instead of PP or PVC
PA 1508 Part 2 Issue 1 Rev 0 Page 16 of 20
SCHEDULE B Item Model ID Model Name Product Description Size range Pic Application
12.7 AWADOCK KG to concrete, reinforced concrete or vitrified clay pipes pipes(dia, type)
AWADOCK, connection of sewer pipes DN150 made from ductile cast iron to concrete or vitrified clay pipes.
Material: SBR/Q-TE-C/PP
Colour: Black/Green
DN150
Types: A, B, C
Connection of sewer pipes DN150 made from ductile cast iron to concrete or vitrified clay pipes
Same as 12.4, only for connection of DN150 ductile iron instead of PP or PVC
12.8 AWADOCK K/U AWADOCK drop to concrete chambers (dia)
AWADOCK as a drop structure or by pass of a drop structure for connection to concrete chambers
Seal flat internally, AWADOCK spigot end DN/OD 160
Material: SBR / Q-TE-C / PP
Colour: Black/Green
DN160 connector
DN200 connector
DN150 (Vitrified clay)
Riser connection or drop connection for concrete chambers.
PA 1508 Part 2 Issue 1 Rev 0 Page 17 of 20
SCHEDULE B
Item Model ID Model Name Product Description Size range Pic Application
12.9 AWADOCK AWADOCK to plane walls or square concrete chambers (dia)
AWADOCK connection of sewer pipes made of PVC and PP to plane walls or square concrete chambers
Material: SBR/PP
Colour: Black/Green
DN 160 & DN200
Connection of sewer pipes made of PVC and PP to plane walls or square concrete chambers
12.10 AWADOCK AWADOCK to AWASHAFT (dia, type)
AWADOCK, connection of sewer pipes made of PVC and PP to AWASHAFT PP DN1000/800
Material: SBR /PP
Colour: Black/Green
DN160/200 types: Standard, K/U
Connection of sewer pipes made of PVC and PP to AWASHAFT PP DN1000/800
12.11 AWADOCK KG - CP
AWADOCK KG-CP to corrugated pipes (dia, type)
AWADOCK Connection of sewer pipes made of PVC and PP to twin-wall sewer pipes
Material: elastomer /PP
Colour: Black/Green
KG-CP type A DN160 connector
KG-CP type B DN160 connector
KG-CP type B DN200 connector
Connection of sewer pipes made of PVC and PP to twin-wall sewer pipes
For connection to AWASHAFT DN600 riser
12.12 AWADOCK –Combination set
AWADOCK to concrete or reinforced concrete pipes (dia)
AWADOCK, connection of sewer pipes DN250/315/400 made from PVC and PP to concrete or reinforced concrete pipes
Comprising a connecting seal and AWADUCT SN10 pipe 0.5m; seal length:50mm
Material: PP/SBR
Colour: Orange brown/Black
DN250 & DN315 & DN400
Connection of sewer pipes DN250/315/400 made from PVC and PP to concrete or reinforced concrete pipes
Similar to 12.4 for larger sizes
PA 1508 Part 2 Issue 1 Rev 0 Page 18 of 20
SCHEDULE B
TABLE B6 - AWADUCT FLEX-CONNECT PIPE COUPLER
ApprovalMark ISO Type 5 Product Certification to AS/NZS 4327:1995, Licence No. AMI 74764
Item Model ID Model Name Product Description Type (clamping range)
Pic Application
13 AWADUCT Flex-Connect AWADUCT FLEX-CONNECT PIPE COUPLER
To connect sewer pipes
Material:
PP / EPDM / Stainless Steel / Q-TE-C
Colour: Orange / Black / Silver
110, 125, 160, 200, 250, 315, 400, 500, 630
A pipe coupler used for connecting socket-less sewer pipes and fittings of different outer diameters, wall thickness, materials or surface structures.
It can be used to connect almost all rigid or flexible pipes.
Smooth, ribbed or corrugated pipe can be connected to each other using Flex connect.
It is suitable for connection of pipes and fittings made of ductile iron, cast iron, earthenware (VC), un-plasticised polyvinyl chloride (uPVC), polypropylene (PP), polyethylene (PE), fibre-cement or glass reinforced polyester resin (UP-GFK)
PA 1508 Part 2 Issue 1 Rev 0 Page 19 of 20
SCHEDULE B
TABLE B7 - AWADUCT FLEX CONNECT PIPE COUPLER RANGE
Material No. Type Clamping range (mm) Insertion depth (mm)
11024181001 110 110 – 145 85
11054201001 125 123 – 162 85
11024191001 160 160 – 200 85
11024231001 200 200 – 260 105
11024241001 250 250 – 330 105
11024251001 315 300 – 385 105
11024261001 400 380 – 460 130
11024271001 500 490 – 570 130
11024281001 630 615 - 695 130
FIGURE B2 - AWADUCT FLEX CONNECT COMPONENTS
PA 1508 Part 2 Issue 1 Rev 0 Page 20 of 20
SCHEDULE B
FIGURE B3 - COMPENSATING RING FOR AWADUCT FLEX CONNECT
FIGURE B4 - OFF-CENTRE COMPENSATING RING (EAR) FOR AWADUCT FLEX CONNECT