YG1E2110530003
Tool specifications are subject to change without notice.
YE-E212
for Machining High Hardened Steelfor High Speed Cutting & Dry Cuttingfor Mold & Die
for Machining High Hardened Steelfor High Speed Cutting & Dry Cuttingfor Mold & Die
45
40
35
30
25
20
15
10
5
100
CUTTING CONDITIONTools : 6Flute, X5070 45。HelixSize : Ø16×Ø16×40×110Work Material : •JIS:SKD61(HRc50)
•DIN:X40CrMoV5-1(1.2344)•AISI:H13
Cutting Speed : 96.5 m/min.R.P.M : 1,920 rev./min.Feed : 912 mm/min.Milling Method : Down & Side CuttingMilling Depth :Axial : 24 mm
Radial : 0.96 mmCoolant : Dry CutOverhang : 52 mmMachine : Machining Center
Carbide 6FL. 45。Helix End Mill for Hardened Steel
YG-1 (Total Milling Length 100m)
Competitor A(Total Milling Length 100m)
350
300
250
200
150
100
50
CUTTING CONDITIONTools : 4Flute, X5070 Ball NoseSize : Ø10×Ø10×18×100Work Material : •JIS:SKD11(HRc60)
•DIN:X155CrVMo12-1(1.2379)•AISI:D2
Cutting Speed : 210.486 m/min.R.P.M : 6,700 rev./min.Feed : 2,800 mm/min.Milling Method : Side CuttingMilling Depth :Axial : 0.2 mm
Radial : 0.5 mmCoolant : Oil MistOverhang : 32 mmMachine : Machining Center
Carbide 4FL. Center Match Ball End Mill for Hardened Steel
YG-1 (Total Milling Length 540m)
Competitor A(Total Milling Length 210m)
More number of flutes than normal 2F ball E/M makes high-feed cutting.
For X-Y wide cutting pitch, high effective cutting performs in short tool working time.
(Example of performance : for the material HRc 50~55)
By using straight flute, the rigidity of corner radius is improved. And it's also possible to get less damage to end
teeth and radius than normal radius end mill
X-Y: 0.05D
Z
X-Y: 0.3D
Z
High Feed End Mill
Normal Ball End Mill
4F Ø10×R2
2F Ø10×R5
5,400
7,500
11,000
2,500
DEPTH OF CUT
0.2
0.2
3.0
0.5
High speed roughing
High speed finishing.. Mirror like surface
High Feed End Mill Capabilities :
For cutting on slope and corner, the remaining part to be cut is smaller than one which comes from the
working with normal ball end mill. It saves the time and cost.
Normal Ball End Mill High Feed End Mill
Normal Ball End Mill Normal Corner Radius End Mill High Feed End Mill
ITEM RPM FEEDSIZEZ (mm) X-Y (mm)
3•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
SELECTION GUIDESSELECTION GUIDESSELECTION GUIDESELECTION GUIDESS
2 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
ITEM MODEL DESCRIPTIONSIZE
MIN MAXPAGE
CARBIDE, 4 FLUTE STUB LENGTH CORNER RADIUS HIGH FEED
CARBIDE, 4 FLUTE STUB LENGTH CORNER RADIUS HIGH FEED
CARBIDE, 2 FLUTE BALL NOSE for RIB PROCESSING
CARBIDE, 2 FLUTE BALL NOSE for RIB PROCESSING
CARBIDE, 2 FLUTE BALL NOSE
CARBIDE, 2 FLUTE STUB LENGTH BALL NOSE with EXTENDED NECK
CARBIDE, 2 FLUTE MINIATURE BALL NOSE
CARBIDE, 3 FLUTE BALL NOSE
CARBIDE, 4 FLUTE BALL NOSE - Center Match
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING
CARBIDE, 2 FLUTE STUB LENGTH CORNER RADIUS with EXTENDED NECK
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING
CARBIDE, 2 FLUTE MINIATURE CORNER RADIUS
CARBIDE, 4 FLUTE CORNER RADIUS with EXTENDED NECK
CARBIDE, 4 FLUTE STUB LENGTH CORNER RADIUS with EXTENDED NECK
CARBIDE, 4 FLUTE CORNER RADIUS with EXTENDED NECK
CARBIDE, 6 FLUTE 45°HELIX CORNER RADIUSwith EXTENDED NECK
CARBIDE, 2 FLUTE for RIB PROCESSING
CARBIDE, 2 FLUTE with EXTENDED NECK
CARBIDE, 4 FLUTE with EXTENDED NECK
CARBIDE, 6&8 FLUTE 45°HELIX LONG LENGTH
CARBIDE, 6&8 FLUTE 45°HELIX EXTRA LONG LENGTH
RECOMMENDED CUTTING CONDITIONS
G8B59
G8B54
G8A46
G8A54
G8A28
G8A38
G8A53
G8A59
G8D62
G8A60
G8A36
G8A52
G8A50
G8A47
G8A37
G8B08
G8A39
G8A45
G8A01
G8A02
G8D63
G8D64
D2.0
D2.0
R0.05
R0.25
R0.05
R0.5
R0.2
R1.5
R1.5
D0.5
D0.3
D0.5
D0.3
D3.0
D1.0
D6.0
D6.0
D0.1
D0.1
D1.0
D6.0
D6.0
D12.0
D16.0
R2.0
R1.0
R6.0
R12.5
R1.0
R10.0
R10.0
D12.0
D20.0
D2.0
D2.0
D12.0
D20.0
D12.0
D20.0
D4.0
D20.0
D20.0
D25.0
D25.0
4
7
8
9
10
11
12
13
16
17
18
19
20
21
22
23
26
27
28
29
30
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
CarbonSteels
AlloySteels
Prehardened Steels
Copper Graphite Cast Iron Aluminum StainlessSteels Titanium Inconel
Hardened Steels High HardenedSteels
~HB225 HB225~325 HRc30~40 HRc40~45 HRc45~55 HRc55~70
◎ : Excellent, ◯ : Good
SELECTION GUIDE
G8B54 SERIESPLAIN SHANK
5•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8B59 SERIESPLAIN SHANK
4 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 4 FLUTE STUB LENGTH CORNER RADIUS HIGH FEED▶Excellent wear resistance at heavy feed rates on high hardened material.▶Designed with reduced clearance angles and short flutes for strength.▶High hardness & heat resistance coating for long life in dry applications.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
R↙
L2L3
L1
D1D2
RD3
G8B5902005G8B5903005G8B5904005G8B5906005G8B5906010G8B5908010G8B5908020G8B5910010G8B5910020G8B5912020G8B5912030
R0.5R0.5R0.5R0.5R1.0R1.0R2.0R1.0R2.0R2.0R3.0
2.03.04.06.06.08.08.010.010.012.012.0
11.21.52.52.53.53.54455
68101212161620202525
5050506060606070708080
1.82.83.85.45.47.27.2991111
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
CornerRadius
R (±0.005)
Unit : mm
666668810101212
ShankDiameter
D2
P.32, 33
Mill Dia.Tolerance (mm)
Corner RadiusTolerance (mm)
0~-0.02 ±0.005
Shank Dia.Tolerance
h6
CARBIDE, 4 FLUTE STUB LENGTH CORNER RADIUS HIGH FEED▶ Excellent wear resistance at heavy feed rates on high hardened material.▶ Designed with reduced clearance angles and short flutes for strength.▶ High hardness & heat resistance coating for long life in dry applications.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
R↙
L2L3
L1
D1D2
RD3
G8B5402005G8B5403005G8B5404005G8B5405005G8B5406005G8B5406010G8B5408010G8B5408020G8B5410010G8B5410020G8B5412020G8B5412030G8B5416030
R0.5R0.5R0.5R0.5R0.5R1.0R1.0R2.0R1.0R2.0R2.0R3.0R3.0
2.03.04.05.06.06.08.08.010.010.012.012.016.0
11.21.52
2.52.53.53.54455
6.5
681010121216162020252530
707070709090100100100100110110130
1.82.83.84.65.45.45.47.27.2991111
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
CornerRadius
R (±0.005)
Unit : mm
666666881010121216
ShankDiameter
D2
P.32, 33
Mill Dia.Tolerance (mm)
Corner RadiusTolerance (mm)
0~-0.02 ±0.005
Shank Dia.Tolerance
h6
Hign Feed End Mill Normal End Mill
Comparison of the endteeth shape
Reduced clearance angles andshort flutes strengthens corner radiusand reduces chattering
Extra-short flute length for high rigidity
Heavy core with reduceddiameter allows greater depthsand maximum rigidity
G8A46 SERIESPLAIN SHANK
6 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A46 SERIESPLAIN SHANK
7•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 2 FLUTE BALL NOSE for RIB PROCESSING▶Designed to machine high hardened materials.▶Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶Excellent workpiece finish.▶Designed for high precision milling operation.▶Higher wear-resistance.
R↙
L3
L1
L2
D3R
D1D2
P.34
G8A46805G8A46806G8A46002G8A46977G8A46958G8A46003G8A46959G8A46986G8A46004G8A46960G8A46961G8A46981G8A46987G8A46005G8A46804G8A46962G8A46963G8A46964G8A46957G8A46988G8A46915G8A46989G8A46916G8A46917G8A46990G8A46918G8A46919G8A46008G8A46901
R0.05R0.05R0.1R0.1R0.1R0.15R0.15R0.15R0.2R0.2R0.2R0.2R0.2R0.25R0.25R0.25R0.25R0.25R0.3R0.3R0.3R0.3R0.3R0.3R0.3R0.4R0.4R0.4R0.4
0.10.10.20.20.20.30.30.30.40.40.40.40.40.50.50.50.50.50.60.60.60.60.60.60.60.80.80.80.8
0.10.10.20.20.20.30.30.30.40.40.40.40.40.40.40.40.40.40.50.50.50.50.50.50.50.60.60.60.6
0.30.50.51
1.5123123452
2.5468234568102468
4545454545454545454545454545454545454545454545454545454545
0.0850.0850.170.170.170.270.270.270.370.370.370.370.370.450.450.450.450.450.550.550.550.550.550.550.550.750.750.750.75
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
Radius ofBall Nose
R (±0.005)
Unit : mm
44444444444444444444444444444
ShankDiameter
D2
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
CARBIDE, 2 FLUTE BALL NOSE for RIB PROCESSING▶Designed to machine high hardened materials.▶Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶Excellent workpiece finish.▶Designed for high precision milling operation.▶Higher wear-resistance.
R↙
L3
L1
L2
D3R
D1D2
P.34
G8A46965G8A46920G8A46921G8A46923G8A46010G8A46924G8A46902G8A46925G8A46903G8A46904G8A46926G8A46927G8A46966G8A46982G8A46012G8A46983G8A46905G8A46930G8A46015G8A46931G8A46906G8A46992G8A46907G8A46932G8A46939G8A46940G8A46020G8A46941G8A46942
R0.4R0.5R0.5R0.5R0.5R0.5R0.5R0.5R0.5R0.5R0.5R0.5R0.5R0.6R0.6R0.6R0.6R0.75R0.75R0.75R0.75R0.75R0.75R0.75R1.0R1.0R1.0R1.0R1.0
0.81.01.01.01.01.01.01.01.01.01.01.01.01.21.21.21.21.51.51.51.51.51.51.52.02.02.02.02.0
0.60.80.80.80.80.80.80.80.80.80.80.80.81.01.01.01.01.21.21.21.21.21.21.21.61.61.61.61.6
10345678910121416206810126810121416204681012
4545454545454545454550505545454545454545455050554545454550
0.750.950.950.950.950.950.950.950.950.950.950.950.951.151.151.151.151.451.451.451.451.451.451.451.951.951.951.951.95
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
Radius ofBall Nose
R (±0.005)
Unit : mm
44444444444444444444444444444
ShankDiameter
D2
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
G8A46 SERIESPLAIN SHANK
8 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A54 SERIESPLAIN SHANK
9•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 2 FLUTE BALL NOSE for RIB PROCESSING▶Designed to machine high hardened materials.▶Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶Excellent workpiece finish.▶Designed for high precision milling operation.▶Higher wear-resistance.
R↙
L3
L1
L2
D3R
D1D2
P.34
G8A46943G8A46909G8A46993G8A46910G8A46944G8A46945G8A46967G8A46948G8A46984G8A46030G8A46985G8A46911G8A46968G8A46969G8A46970G8A46950G8A46040G8A46912G8A46913G8A46971G8A46972G8A46973G8A46974G8A46975
R1.0R1.0R1.0R1.0R1.0R1.0R1.0R1.5R1.5R1.5R1.5R1.5R1.5R1.5R1.5R2.0R2.0R2.0R2.0R2.0R2.0R2.0R2.0R2.0
2.02.02.02.02.02.02.03.03.03.03.03.03.03.03.04.04.04.04.04.04.04.04.04.0
1.61.61.61.61.61.61.62.42.42.42.42.42.42.42.43.23.23.23.23.23.23.23.23.2
141618202225301214161820253035121620253035404550
5050555560607050555560606570806060657070809090100
1.951.951.951.951.951.951.952.852.852.852.852.852.852.852.853.853.853.853.853.853.853.853.853.85
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
Radius ofBall Nose
R (±0.005)
Unit : mm
444444466666666666666666
ShankDiameter
D2
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Mill Dia.Tolerance(mm)
0~-0.012
Shank Dia.Tolerance
h6
CARBIDE, 2 FLUTE BALL NOSE for RIB PROCESSING▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
R↙
L3
L1
L2
D3R
D1D2
P.34
G8A54005G8A54901G8A54006G8A54902G8A54008G8A54903G8A54010G8A54904G8A54905G8A54012G8A54906G8A54015G8A54907G8A54908G8A54020G8A54909G8A54910
R0.25R0.25R0.3R0.3R0.4R0.4R0.5R0.5R0.5R0.6R0.6R0.75R0.75R0.75R1.0R1.0R1.0
0.50.50.60.60.80.81.01.01.01.21.21.51.51.52.02.02.0
0.50.50.60.60.80.8111
1.21.21.51.51.5222
1.53.324
2.55.53.36.7124.485
9.71561320
5050505050505050505050505050505060
0.450.450.550.550.750.750.950.950.951.151.151.451.451.451.951.951.95
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
Radius ofBall Nose
R (±0.005)
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
66666666666666666
ShankDiameter
D2
Mill Dia.Tolerance(mm)
0~-0.012
Shank Dia.Tolerance
h6
G8A38 SERIESPLAIN SHANK
11•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A28 SERIESPLAIN SHANK
10 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 2 FLUTE BALL NOSE▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 2 FLUTE STUB LENGTH BALL NOSE with EXTENDED NECK▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
R↙
L1
L2
L3
D2
R
D1
D3
P.36
R0.05~R3 R4~R6
G8A28001G8A28002G8A28003G8A28004G8A28005G8A28006G8A28007G8A28008G8A28009G8A28010G8A28015G8A28020G8A28025G8A28030G8A28035G8A28040G8A28045G8A28050G8A28055G8A28060G8A28903G8A28901G8A28080G8A28904G8A28902G8A28100G8A28905G8A28120
R0.05R0.1R0.15R0.2R0.25R0.3R0.35R0.4R0.45R0.5R0.75R1.0R1.25R1.5R1.75R2.0R2.25R2.5R2.75R3.0R3.0R4.0R4.0R4.0R5.0R5.0R5.0R6.0
0.10.20.30.40.50.60.70.80.91.01.52.02.53.03.54.04.55.05.56.06.08.08.08.010.010.010.012.0
0.20.30.50.60.70.91.11.21.41.52
2.534
4.55
5.56
6.579991211111514
---------3457101010101212153015153025253025
4040404040404040405050505060606060606060906080100608010080
---------
0.951.451.952.42.853.353.854.354.855.355.855.857.77.77.79.79.79.711.7
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
Radius ofBall Nose
R
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
44444444466666666666688810101012
ShankDiameter
D2
RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.005±0.010
0~-0.0120~-0.015
up to R3over R3
Shank Dia.Tolerance
h6
R↙
L1
L2
L3
D2
R
D1
D3
P.36
R0.5~R3 R3.5~R12.5
G8A38010G8A38012G8A38015G8A38020G8A38030G8A38040G8A38050G8A38060G8A38070G8A38080G8A38090G8A38100G8A38120G8A38140G8A38160G8A38180G8A38200G8A38250
R0.5R0.6R0.75R1.0R1.5R2.0R2.5R3.0R3.5R4.0R4.5R5.0R6.0R7.0R8.0R9.0R10.0R12.5
1.01.21.52.03.04.05.06.07.08.09.010.012.014.016.018.020.025.0
11.21.52345678910121416182025
2.22.63468101214161820242832364050
505050506070809090100100100110110140140160180
0.951.151.451.952.853.854.855.856.77.78.79.711.713.715.717.719.724.7
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
Radius ofBall Nose
R
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
44466666881010121416182025
ShankDiameter
D2
RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.005±0.010
0~-0.0120~-0.015
up to R3over R3
Shank Dia.Tolerance
h6
G8A59 SERIESPLAIN SHANK
13•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A53 SERIESPLAIN SHANK
12 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 2 FLUTE MINIATURE BALL NOSE▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 3 FLUTE BALL NOSE▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
R↙
L1
L2
D2
R
D1
R↙
L2
L1
D2
R
D1
P.36 P.35
R1.5~R3 R4~R10
G8A53004G8A53005G8A53006G8A53008G8A53010G8A53012G8A53015G8A53020
R0.2R0.25R0.3R0.4R0.5R0.6R0.75R1.0
5050505050505050
0.40.50.60.81.01.21.52.0
66666666
0.40.50.60.81.01.21.52.0
EDP No.OverallLength
L2
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
Radius ofBall Nose
R (±0.005)
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Mill Dia.Tolerance(mm)
0~-0.012
Shank Dia.Tolerance
h6
G8A59030G8A59040G8A59050G8A59060G8A59080G8A59100G8A59120G8A59160G8A59200
R1.5R2.0R2.5R3.0R4.0R5.0R6.0R8.0R10.0
60708090100100110140160
8810121418223038
6666810121620
3.04.05.06.08.010.012.016.020.0
EDP No.OverallLength
L2
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
Radius ofBall Nose
R
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.005±0.010
0~-0.0120~-0.015
up to R3over R3
Shank Dia.Tolerance
h6
G8A60 SERIESPLAIN SHANK
15•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8D62 SERIESPLAIN SHANK
14 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8D62030G8D62040G8D62050G8D62060G8D62080G8D62100G8D62120G8D62160G8D62200
R1.5R2.0R2.5R3.0R4.0R5.0R6.0R8.0R10.0
60708090100100110140160
8810121418223038
6666810121620
3.04.05.06.08.010.012.016.020.0
EDP No.Radius ofBall Nose
R
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.005±0.010
0~-0.0120~-0.015
up to R3over R3
Shank Dia.Tolerance
h6
CARBIDE, 4 FLUTE BALL NOSE - Center Match▶Applied center match type & special new design on ball center shape.▶Excellent high wear resistance and high performance.▶Applied for high speed and feed.▶ Increased the surface roughness.
P.37
R1.5~R3 R4~R10
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
R↙
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
R↙
L2L3
L1
D2 D1
RD3
P.38, 39
Ø0.5~Ø6 Ø8~Ø12
G8A60936G8A60932G8A60935G8A60931G8A60933G8A60934G8A600060102G8A600070104G8A600080102G8A60008G8A60924G8A60925G8A60926G8A60010G8A60910G8A60911G8A60912G8A60930G8A600100308G8A60015G8A600150206G8A600150208G8A60913G8A60914G8A60915G8A600150306G8A600150308G8A60927G8A600200208
0.450.450.450.550.550.550.550.650.750.750.750.950.950.950.950.950.950.950.951.451.451.451.451.451.451.451.451.951.95
4545454545454545454545505050505050505050505050505050505050
1.52.542342424646468468468101246868
0.70.70.70.90.90.90.91
1.21.21.21.51.51.51.51.51.51.51.52.52.52.52.52.52.52.52.533
44444444444666666666666666666
0.50.50.50.60.60.60.60.70.80.80.81.01.01.01.01.01.01.01.01.51.51.51.51.51.51.51.52.02.0
R0.05R0.05R0.05R0.05R0.05R0.05R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.2R0.2R0.2R0.3R0.3R0.3R0.2R0.2R0.2R0.2R0.2R0.3R0.3R0.3R0.2R0.2
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
CornerRadius
R
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
L1
L2
D2
R
D1
MillDiameter
D1
ShankDiameter
D2
Lengthof Cut
L1
OverallLength
L2
G8A60 SERIESPLAIN SHANK
17•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A60 SERIESPLAIN SHANK
16 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A600200210G8A600200212G8A60916G8A600200308G8A600200310G8A600200312G8A600200316G8A60917G8A60020G8A60918G8A600300208G8A600300210G8A600300212G8A600300216G8A600300308G8A60919G8A600300312G8A600300316G8A60030G8A600300512G8A60901G8A60902G8A600400212G8A600400216G8A600400220G8A600400310G8A60920G8A600400316G8A600400320
1.951.951.951.951.951.951.951.951.951.952.852.852.852.852.852.852.852.852.852.852.852.853.853.853.853.853.853.853.85
5555505055555550555555555555555555555555555555555555555555
10126810121661012810121681012161012162012162010121620
33333333334444444444445555555
66666666666666666666666666666
2.02.02.02.02.02.02.02.02.02.03.03.03.03.03.03.03.03.03.03.03.03.04.04.04.04.04.04.04.0
R0.2R0.2R0.3R0.3R0.3R0.3R0.3R0.5R0.5R0.5R0.2R0.2R0.2R0.2R0.3R0.3R0.3R0.3R0.5R0.5R0.5R0.5R0.2R0.2R0.2R0.3R0.3R0.3R0.3
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
CornerRadius
R
Unit : mm
G8A60040G8A60903G8A60904G8A600401012G8A600401016G8A60921G8A60060G8A60905G8A60906G8A600602020G8A60922G8A60929G8A60080G8A60907G8A600802025G8A60923G8A601000532G8A60100G8A60908G8A601002032G8A601200538G8A60120G8A60909G8A601202038
3.853.853.853.853.855.855.855.855.855.857.77.77.77.77.79.79.79.79.79.711.711.711.711.7
555555555560606060606060606060707070707080808080
121620121620202020202525252525323232323238383838
555557777799999111111111112121212
666666666688888101010101012121212
4.04.04.04.04.06.06.06.06.06.08.08.08.08.08.010.010.010.010.010.012.012.012.012.0
R0.5R0.5R0.5R1.0R1.0R0.3R0.5R1.0R1.5R2.0R0.3R0.5R1.0R1.5R2.0R0.3R0.5R1.0R1.5R2.0R0.5R1.0R1.5R2.0
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
CornerRadius
R
Unit : mm
Corner RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.010±0.015
0~-0.0120~-0.015
up to Ø6over Ø6
Shank Dia.Tolerance
h6Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
P.38, 39
Ø0.5~Ø6 Ø8~Ø12
P.38, 39
Ø0.5~Ø6 Ø8~Ø12
R↙
L2L3
L1
D2 D1
RD3
R↙
L3L1
D1D2
R
L2
D3
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
G8A52 SERIESPLAIN SHANK
19•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A36 SERIESPLAIN SHANK
18 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 2 FLUTE STUB LENGTH CORNER RADIUS with EXTENDED NECK▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
R↙
L3
L1
L2
D1D2
RD3
P.44, 45
Ø0.3~Ø6 Ø8~Ø20
G8A36003G8A36004G8A36005G8A36907G8A36006G8A36908G8A36909G8A36008G8A36910G8A36911G8A36010G8A36901G8A36903G8A36015G8A36904G8A36020G8A36902G8A36905G8A36025G8A36906G8A36030G8A36035G8A36040G8A36045G8A36050G8A36060G8A36080G8A36100G8A36120G8A36160G8A36200
--
R0.05R0.05R0.05R0.05R0.05R0.05R0.05R0.05R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.2R0.2R0.2R0.2R0.3R0.3R0.3
0.30.40.50.50.60.60.70.80.80.91.01.01.01.51.52.02.02.02.52.53.03.54.04.55.06.08.010.012.016.020.0
0.450.60.71
0.91.21.41.21.62
1.51.51.52.22.233344455667912151824
---------------666667991011141825303845
404040404040404040404040404040404040404045454545505060757590100
---------------
1.951.951.952.42.42.853.353.854.354.855.857.79.711.715.719.7
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
CornerRadius
R
Unit : mm
33343443443463634636666666810121620
ShankDiameter
D2
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Corner RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.010±0.015
0~-0.0120~-0.015
up to Ø6over Ø6
Shank Dia.Tolerance
h6
R↙
L1
L2
D1D2
L3
R
D3
P.40
G8A52005G8A52901G8A52006G8A52902G8A52008G8A52903G8A52010G8A52904G8A52012G8A52905G8A52015G8A52906G8A52020G8A52907
R0.05R0.05R0.05R0.05R0.05R0.05R0.1R0.1R0.1R0.1R0.15R0.15R0.15R0.15
0.50.50.60.60.80.81.01.01.21.21.51.52.02.0
0.70.70.90.91.21.21.51.51.81.82.22.22.22.2
1.53.324
2.55.53.36.74.485
9.7613
5050505050505050505050505050
0.450.450.550.550.750.750.950.951.151.151.451.451.951.95
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
CornerRadius
R (±0.010)
Unit : mm
66666666666666
ShankDiameter
D2
Mill Dia.Tolerance(mm)
0~-0.012
Shank Dia.Tolerance
h6
G8A47 SERIESPLAIN SHANK
21•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A50 SERIESPLAIN SHANK
20 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 2 FLUTE MINIATURE CORNER RADIUS▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 4 FLUTE CORNER RADIUS with EXTENDED NECK▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
P.42
Ø3~Ø6 Ø8~Ø12
P.41
R↙
L1
L2
D2
R
D1
R↙
L3L1
L2
D1D2
RD3
G8A50003G8A50004G8A50005G8A50006G8A50008G8A50010G8A50012G8A50015G8A50020
--
R0.05R0.05R0.05R0.1R0.1R0.15R0.15
505050505050505050
0.450.60.70.91.21.51.82.22.2
666666666
0.30.40.50.60.81.01.21.52.0
EDP No.OverallLength
L2
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
CornerRadius
R (±0.010)
Unit : mm
Mill Dia.Tolerance(mm)
0~-0.012
Shank Dia.Tolerance
h6
G8A47916G8A47917G8A47918G8A47030G8A47901G8A47902G8A47919G8A47920G8A47921G8A47040G8A47903G8A47904G8A47922G8A47060G8A47905G8A47906G8A47910G8A47080G8A47907G8A47913G8A47911G8A47100G8A47908G8A47914G8A47912G8A47120G8A47909G8A47915
R0.3R0.3R0.3R0.5R0.5R0.5R0.3R0.3R0.3R0.5R0.5R0.5R1.0R0.5R1.0R1.5R0.5R1.0R1.5R2.0R0.5R1.0R1.5R2.0R0.5R1.0R1.5R2.0
3.03.03.03.03.03.04.04.04.04.04.04.04.06.06.06.08.08.08.08.010.010.010.010.012.012.012.012.0
444444555555577799991111111112121212
12162010162012162012162012202020252525253232323238383838
55555555555555555555555555606060606060607070707080808080
2.852.852.852.852.852.853.853.853.853.853.853.853.855.855.855.857.77.77.77.79.79.79.79.711.711.711.711.7
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
CornerRadius
R
Unit : mm
666666666666666688881010101012121212
ShankDiameter
D2
Corner RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.010±0.015
0~-0.0120~-0.015
up to Ø6over Ø6
Shank Dia.Tolerance
h6
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
G8B08 SERIESPLAIN SHANK
23•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A37 SERIESPLAIN SHANK
22 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 4 FLUTE STUB LENGTH CORNER RADIUS with EXTENDED NECK▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 4 FLUTE CORNER RADIUS with EXTENDED NECK▶ Designed to machine high hardened materials.▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
P.42
Ø6 Ø8~Ø12
P.46
Ø1~Ø6 Ø8~Ø20
R↙
L2L3
L1
D1D2
RD3
R↙
L2
L3
L1
D1D2
RD3
Corner RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.010±0.015
0~-0.0120~-0.015
up to Ø6over Ø6
Shank Dia.Tolerance
h6
G8B0806005090G8B0806010090G8B0808005100G8B0808010100G8B0810005100G8B0810010100G8B0810020100G8B0812005110G8B0812010110G8B0812020110
5.855.857.77.79.79.79.711.711.711.7
9090100100100100100110110110
20202525323232383838
991212151515181818
6688101010121212
6.06.08.08.010.010.010.012.012.012.0
R0.5R1.0R0.5R1.0R0.5R1.0R2.0R0.5R1.0R2.0
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
CornerRadius
R
Unit : mm
G8A37010G8A37901G8A37015G8A37902G8A37020G8A37903G8A37025G8A37904G8A37030G8A37035G8A37040G8A37045G8A37050G8A37060G8A37080G8A37100G8A37120G8A37160G8A37200
R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.1R0.2R0.2R0.2R0.2R0.3R0.3R0.3
1.01.01.51.52.02.02.52.53.03.54.04.55.06.08.010.012.016.020.0
1.51.52.22.23344455667912151824
----66667991011141825303845
404040404040404045454545505060757590100
----
1.951.952.42.42.853.353.854.354.855.857.79.711.715.719.7
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
CornerRadius
R
Unit : mm
36363636666666810121620
ShankDiameter
D2
Corner RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.010±0.015
0~-0.0120~-0.015
up to Ø6over Ø6
Shank Dia.Tolerance
h6
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
G8A45 SERIESPLAIN SHANK
25•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A39 SERIESPLAIN SHANK
24 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 6 FLUTE 45。。HELIX CORNER RADIUS with EXTENDED NECK▶ Designed to machine high hardened materials▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Deep slotting is possible by reduced neck.▶ Corner radius for preventing the chipping in high speed machining▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 2 FLUTE for RIB PROCESSING▶ Designed to machine high hardened materials▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
P.43P.47
Ø6 Ø8~Ø20
L1
L2
D1D2
L3
D3
R↙
L2
L3
L1
D1D2
RD3
G8A39916G8A39060G8A39901G8A39910G8A39080G8A39902G8A39911G8A39903G8A39100G8A39904G8A39912G8A39905G8A39120G8A39906G8A39913G8A39160G8A39907G8A39914G8A39200G8A39908G8A39909G8A39915
R0.25R0.5R0.5R0.5R0.5R0.5R0.5R0.5R1.0R1.0R1.0R0.5R1.0R1.0R1.0R1.0R1.5R1.5R1.0R1.5R2.0R2.0
6.06.06.06.08.08.08.010.010.010.010.012.012.012.012.016.016.016.020.020.020.020.0
66132681936221022462612265632326638383876
1414--
24---
30---
30---------
505070706090901007010010011075110110130130130140140140140
5.855.85
--
7.7---
9.7---
11.7---------
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
MillDiameter
D1
CornerRadius
R
Unit : mm
6666888101010101212121216161620202020
✽
✽
✽
✽
✽
✽
ShankDiameter
D2
Corner RadiusTolerance (mm)
Mill Dia.Tolerance (mm)
Size
±0.010±0.015
0~-0.02(✽Extra Long Type : 0~-0.03)
up to Ø6over Ø6
Shank Dia.Tolerance
h6
G8A45863G8A45864G8A45002G8A45815G8A45816G8A45003G8A45844G8A45817G8A45818G8A45842G8A45843G8A45004G8A45984G8A45985G8A45986G8A45005G8A45861G8A45988G8A45989G8A45990G8A45006G8A45860G8A45991G8A45992G8A45993G8A45819G8A45862G8A45008G8A45908
0.0850.0850.170.170.170.270.270.270.270.270.370.370.370.370.370.450.450.450.450.450.550.550.550.550.550.550.750.750.75
4545454545454545454545454545454545454545454545454545454545
0.30.50.51
1.51
1.5234123452
2.54682346810246
0.150.150.30.30.30.450.450.450.450.450.60.60.60.60.60.70.70.70.70.70.90.90.90.90.90.91.21.21.2
44444444444444444444444444444
0.10.10.20.20.20.30.30.30.30.30.40.40.40.40.40.50.50.50.50.50.60.60.60.60.60.60.80.80.8
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
G8A45 SERIESPLAIN SHANK
27•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A45 SERIESPLAIN SHANK
26 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A45963G8A45964G8A45966G8A45814G8A45975G8A45976G8A45977G8A45978G8A45979G8A45980G8A45981G8A45832G8A45833G8A45983G8A45040G8A45801G8A45802G8A45803G8A45834G8A45835G8A45836G8A45837G8A45838
1.951.951.951.952.852.852.852.852.852.852.852.852.852.853.853.853.853.853.853.853.853.853.85
55556070454550555560657080905060607070809090100
1820253010121416182025303540121620253035404550
3.03.03.03.04.54.54.54.54.54.54.54.54.54.5666666666
44446666666666666666666
2.02.02.02.03.03.03.03.03.03.03.03.03.03.04.04.04.04.04.04.04.04.04.0
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
Unit : mm
Mill Dia.Tolerance(mm)
0~-0.012
Shank Dia.Tolerance
h6
G8A45909G8A45994G8A45995G8A45996G8A45010G8A45912G8A45913G8A45914G8A45997G8A45998G8A45012G8A45915G8A45916G8A45917G8A45999G8A45015G8A45923G8A45924G8A45925G8A45926G8A45927G8A45928G8A45810G8A45958G8A45020G8A45959G8A45960G8A45961G8A45962
0.750.750.750.950.950.950.950.950.950.951.151.151.151.151.151.451.451.451.451.451.451.451.451.951.951.951.951.951.95
4545454545454545505545454545504545454550505555454545455050
810124681012162068101216681012141618206810121416
1.21.21.21.51.51.51.51.51.51.51.81.81.81.81.82.32.32.32.32.32.32.32.33.03.03.03.03.03.0
44444444444444444444444444444
0.80.80.81.01.01.01.01.01.01.01.21.21.21.21.21.51.51.51.51.51.51.51.52.02.02.02.02.02.0
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
Unit : mm
CARBIDE, 2 FLUTE for RIB PROCESSING▶ Designed to machine high hardened materials▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
P.43
L1
L2
D1D2
L3
D3
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
CARBIDE, 2 FLUTE for RIB PROCESSING▶ Designed to machine high hardened materials▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
P.43
L1
L2
D1D2
L3
D3
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
G8A02 SERIESPLAIN SHANK
29•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A01 SERIESPLAIN SHANK
28 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 2 FLUTE with EXTENDED NECK▶ Designed to machine high hardened materials▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 4 FLUTE with EXTENDED NECK▶ Designed to machine high hardened materials▶ Suitable for dry cutting, high speed cutting thanks to newly developed raw-material and new coating.▶ Excellent workpiece finish.▶ Designed for high precision milling operation.▶ Higher wear-resistance.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
L2L3
L1
D1D2
D3
L3L1
L2
D1D2
D3
P.46P.44, 45
Mill Dia.Tolerance (mm)
Shank Dia.ToleranceSize
0~-0.0120~-0.015
h6up to Ø6over Ø6
G8A02010G8A02020G8A02030G8A02040G8A02050G8A02060G8A02080G8A02100G8A02120G8A02160G8A02200
0.951.952.853.854.855.857.79.711.715.719.7
50505555555565758590105
3581013152025283240
1.523456810121620
666666810121620
1.02.03.04.05.06.08.010.012.016.020.0
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
Unit : mm
Mill Dia.Tolerance (mm)
Shank Dia.ToleranceSize
0~-0.0120~-0.015
h6up to Ø6over Ø6
G8A01001G8A01002G8A01003G8A01004G8A01005G8A01006G8A01007G8A01008G8A01009G8A01010G8A01015G8A01020G8A01025G8A01030G8A01035G8A01040G8A01050G8A01060G8A01080G8A01100G8A01120G8A01160G8A01200
---------
0.951.451.952.42.853.353.854.855.857.79.711.715.719.7
40404040404040404050505055555555555565758590105
---------3456891013152025283240
0.20.40.60.81
1.21.41.62
1.51.72
2.53
3.5456810121620
444444444666666666810121620
0.10.20.30.40.50.60.70.80.91.01.52.02.53.03.54.05.06.08.010.012.016.020.0
EDP No.Neck
DiameterD3
OverallLength
L2
LengthBelow Shank
L3
Lengthof Cut
L1
ShankDiameter
D2
MillDiameter
D1
Unit : mm
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
G8D64 SERIESPLAIN SHANK
31•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8D63 SERIESPLAIN SHANK
30 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 6&8 FLUTE 45。HELIX LONG LENGTH▶Designed to machine high hardened materials.▶Designed for high abrasion resistance thanks to negative rake angle.▶Excellent side-cutting of press mold field.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
CARBIDE, 6&8 FLUTE 45。HELIX EXTRA LONG LENGTH▶Designed to machine high hardened materials.▶Designed for high abrasion resistance thanks to negative rake angle.▶Excellent side-cutting of press mold field.
○ ○ ◎ ◎
CarbonSteels
~HB225
AlloySteels
HB225~325
Prehardened Steels
HRc30~40
Hardened Steels High HardenedSteels
HRc40~45 HRc45~55 HRc55~70Copper Graphite Cast Iron Aluminum Stainless
Steels Titanium Inconel
◎ : Excellent ◯ : Good
G8D63060G8D63080G8D63100G8D63120G8D63140G8D63160G8D63180G8D63200G8D63250
6.08.010.012.014.016.018.020.025.0
6810121416182025
131922262632323844
57637283839292104104
666666888
EDP No. No. ofFlute
OverallLength
Lengthof Cut
ShankDiameter
MillDiameter
L2L1D2D1
Unit : mm
Mill Dia.Tolerance(mm)
0~-0.02
Shank Dia.Tolerance
h6
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
P.48
G8D64060G8D64080G8D64100G8D64120G8D64160G8D64200G8D64250
6.08.010.012.016.020.025.0
681012162025
26364656667692
7090100110130140180
6666688
EDP No. No. ofFlute
Unit : mm
Mill Dia.Tolerance(mm)
0~-0.03
Shank Dia.Tolerance
h6
Due to the characteristics of blue decoration layer which might be earased during short term using, the color layer might not be uniform moreover. However, it doesn’t effect on performance of tool.
P.49
L1
L2
D2 D1
L1
L2
D2 D1
OverallLength
Lengthof Cut
ShankDiameter
MillDiameter
L2L1D2D1
33•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 4FLUTE CORNER RADIUS HIGH FEED
G8B59, G8B54 SERIES
2.0 × R0.53.0 × R0.54.0 × R0.55.0 × R0.56.0 × R0.56.0 × R1.08.0 × R1.08.0 × R2.010.0 × R1.010.0 × R2.012.0 × R2.012.0 × R3.016.0 × R3.0
13500955079506500580058004350435035003500290029002200
6500650070007300765076507650765076507650765076507650
85 90 100 100 110 110 110 110 110 110 110 110 110
0.120 0.170 0.220 0.281 0.330 0.330 0.440 0.440 0.546 0.546 0.659 0.659 0.869
MATERIAL
HARDNESS ~ HRc 40
DIAMETER RPM FEED Vc Fz
HARDENED STEELS
■ NORMAL SPEED
0.5D
0.2R
9550690057504800410041003050305024502450205020501550
3800415046004800490049004900490049004900490049004900
60 65 70 75 75 75 75 75 75 75 75 75 80
0.099 0.150 0.200 0.250 0.299 0.299 0.402 0.402 0.500 0.500 0.598 0.598 0.790
HRc 40 ~ HRc 50
RPM FEED Vc Fz
5500455040003400290029002200220017501750145014501100
2200275032003200350035003500350035003500350035003500
35 45 50 55 55 55 55 55 55 55 55 55 55
0.100 0.151 0.200 0.235 0.302 0.302 0.398 0.398 0.500 0.500 0.603 0.603 0.795
HRc 50 ~ HRc 55
RPM FEED Vc Fz
2.0 × R0.53.0 × R0.54.0 × R0.55.0 × R0.56.0 × R0.56.0 × R1.08.0 × R1.08.0 × R2.010.0 × R1.010.0 × R2.012.0 × R2.012.0 × R3.016.0 × R3.0
3200285025502200185018501400140011001100925925700
1000115013501600185018501850185018501850185018501850
20 25 30 35 35 35 35 35 35 35 35 35 35
0.078 0.101 0.132 0.182 0.250 0.250 0.330 0.330 0.420 0.420 0.500 0.500 0.661
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
HARDENED STEELS
RPM = rev./min.FEED = mm/min.
0.5D
0.2R
220019001750150013501350995995795795665665500
550610700700795795795795795795795795795
15 20 20 25 25 25 25 25 25 25 25 25 25
0.063 0.080 0.100 0.117 0.147 0.147 0.200 0.200 0.250 0.250 0.299 0.299 0.398
HRc 60 ~ HRc 65
RPM FEED Vc Fz
CARBIDE, 4FLUTE CORNER RADIUS HIGH FEED
G8B59, G8B54 SERIES
2.0 × R0.53.0 × R0.54.0 × R0.55.0 × R0.56.0 × R0.56.0 × R1.08.0 × R1.08.0 × R2.010.0 × R1.010.0 × R2.012.0 × R2.012.0 × R3.016.0 × R3.0
290002200017000150001350013500100001000080008000660066005000
15000160001750018000185001850018500185001850018500185001850018500
180 205 215 235 255 255 250 250 250 250 250 250 250
0.129 0.182 0.257 0.300 0.343 0.343 0.463 0.463 0.578 0.578 0.701 0.701 0.925
MATERIAL
HARDNESS ~ HRc 40
DIAMETER RPM FEED Vc Fz
HARDENED STEELS
■ HIGH SPEED
0.3D
0.1R
2200017000130001100010500105008000800064006400530053003900
9800100001200012500138001380014000140001400014000140001400014000
140 160 165 175 200 200 200 200 200 200 200 200 195
0.111 0.147 0.231 0.284 0.329 0.329 0.438 0.438 0.547 0.547 0.660 0.660 0.897
HRc 40 ~ HRc 50
RPM FEED Vc Fz
15000125001100010000900090006800680054005400450045003300
78508000920010000110001100011000110001100011000110001100011000
95 200 140 155 170 170 170 170 170 170 170 170 165
0.131 0.160 0.209 0.250 0.306 0.306 0.404 0.404 0.509 0.509 0.611 0.611 0.833
HRc 50 ~ HRc 55
RPM FEED Vc Fz
2.0 × R0.53.0 × R0.54.0 × R0.55.0 × R0.56.0 × R0.56.0 × R1.08.0 × R1.08.0 × R2.010.0 × R1.010.0 × R2.012.0 × R2.012.0 × R3.016.0 × R3.0
11000950080007000640064004800480038003800320032002400
4450460055006000640064006700670068006800700070007000
70 90 100 110 120 120 120 120 120 120 120 120 120
0.101 0.121 0.172 0.214 0.250 0.250 0.349 0.349 0.447 0.447 0.547 0.547 0.729
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
HARDENED STEELS
RPM = rev./min.FEED = mm/min.
0.3D
0.1R
8700690056004900450045003400340027002700225022501650
2450250029003100360036004100410038003800360036003300
55 65 70 75 85 85 85 85 85 85 85 85 85
0.070 0.091 0.129 0.158 0.200 0.200 0.301 0.301 0.352 0.352 0.400 0.400 0.500
HRc 60 ~ HRc 65
RPM FEED Vc Fz
35•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
0.05D
0.02D
0.05D
0.02D
G8A46, G8A54 SERIES
RPM = rev./min.FEED = mm/min.
CARBIDE, 2 FLUTE BALL NOSE for RIB PROCESSING CARBIDE, 3 FLUTE BALL NOSE
G8A59 SERIES
R0.1 ×0.2R0.15×0.3R0.2 ×0.4R0.25×0.5R0.3 ×0.6R0.4 ×0.8R0.5 ×1.0R0.6 ×1.2R0.75×1.5R1.0 ×2.0R1.5 ×3.0R2.0 ×4.0
5000048000~5000048000~5000034100~4950028600~4070022000~3080017600~2420014300~1870011000~143008500~110005700~82004300~6200
300~350480~520720~790600~870590~850640~890600~850590~780580~760590~800730~1000680~990
0.006~0.0160.010~0.0170.013~0.0320.007~0.0280.007~0.0340.016~0.0640.008~0.0800.024~0.0320.031~0.0480.024~0.1600.064~0.2400.080~0.320
31 45~4760~6354~7854~7755~7755~7654~7052~6753~6954~7754~78
0.012~0.0140.020~0.0210.030~0.0320.035~0.0350.041~0.0420.058~0.0580.068~0.0700.083~0.0830.105~0.1060.139~0.1450.256~0.2440.316~0.319
MATERIAL
HARDNESS HRc 30 ~ HRc 45
DIAMETER RPM FEED ap(mm) Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
HRc 45 ~ HRc 55
RPM FEED ap(mm) Vc Fz
HARDENED STEELS
5000048000~5000048000~5000031900~3520026400~2970019800~2200015400~1760012000~1400010000~115007900~88005300~58003950~4400
265~310440~460450~550490~540480~540490~550470~540480~540480~540470~530590~650550~620
0.005~0.0130.008~0.0140.011~0.0260.005~0.0230.006~0.0280.013~0.0520.007~0.0650.020~0.0260.025~0.0390.020~0.1300.052~0.1950.065~0.026
3145~4760~6350~5550~5650~5548~5545~5347~5450~5550~5550~55
0.011~0.0120.018~0.0180.019~0.0220.031~0.0310.036~0.0360.049~0.050.061~0.0610.080~0.0770.096~0.0940.119~0.120.223~0.2240.299~0.282
R0.1 ×0.2R0.15×0.3R0.2 ×0.4R0.25×0.5R0.3 ×0.6R0.4 ×0.8R0.5 ×1.0R0.6 ×1.2R0.75×1.5R1.0 ×2.0R1.5 ×3.0R2.0 ×4.0
5000046000~5000046000~5000031900~3520026400~2970019800~2200015400~1760012000~1400010000~115007900~88005300~58003850~4400
225~265390~420400~460440~480400~480440~500440~500420~480420~480440~480550~620530~570
0.005~0.0120.007~0.0130.010~0.0240.005~0.0210.006~0.0250.012~0.0480.006~0.0600.018~0.0240.023~0.0360.018~0.1200.048~0.1200.060~0.240
31~3143~4758~6350~5550~5650~5548~5545~5347~5450~5550~5548~55
0.009~0.0110.017~0.0170.017~0.0180.028~0.0270.030~0.0320.044~0.0450.057~0.0570.070~0.0690.084~0.0830.111~0.1090.208~0.2140.275~0.259
MATERIAL
HARDNESS HRc 55 ~ HRc 65
DIAMETER RPM FEED ap(mm) Vc Fz
HARDENED STEELS
RPM FEED ap(mm) Vc Fz
COPPER
5000048000~5000048000~5000049000~5000042000~5000031000~5000024000~4950028500~3850017000~2850012600~2400011900~170006600~12500
455~530690~790
1000~11501100~14001100~17001100~22501100~22001480~19501100~19501100~21501850~27001260~2500
0.010~0.0220.002~0.0230.019~0.0480.010~0.0420.011~0.0500.024~0.0960.012~0.1200.036~0.0480.046~0.0720.036~0.2400.096~0.3600.120~0.480
31~3145~4760~6377~7979~9478~12675~156107~14580~13479~151112~16083~157
0.018~0.0210.029~0.0320.042~0.0460.045~0.0560.052~0.0680.071~0.0900.092~0.0890.104~0.1010.129~0.1370.175~0.1790.311~0.3180.382~0.400
R1.5 × 3.0R2.0 × 4.0R2.5 × 5.0R3.0 × 6.0R4.0 × 8.0R5.0 × 10.0R6.0 × 12.0R8.0 × 16.0R10.0 × 20.0
320002408020000180001350010800905067005400
860077007250857073506530610046003600
300 305 315 340 340 340 340 335 340
0.090 0.107 0.121 0.159 0.181 0.202 0.225 0.229 0.222
MATERIAL
HARDNESS HRc 30 ~ HRc 45
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS HARDENED STEELS
26840201301678015200113009100759056904550
580054305430622052504590426032502620
255 255 265 285 285 285 285 285 285
0.072 0.090 0.108 0.136 0.155 0.168 0.187 0.190 0.192
HRc 45 ~ HRc 55
RPM FEED Vc Fz
1984014880124001220092007350613046003670
428038803690450039803450319024801980
185 185 195 230 230 230 230 230 230
0.072 0.087 0.099 0.123 0.144 0.156 0.173 0.180 0.180
HRc 55 ~ HRc 60
RPM FEED Vc Fz
R1.5 × 3.0R2.0 × 4.0R2.5 × 5.0R3.0 × 6.0R4.0 × 8.0R5.0 × 10.0R6.0 × 12.0R8.0 × 16.0R10.0 × 20.0
1868014220116701110083206660553041603300
404036503470383033502870240018001440
175 180 185 210 210 210 210 210 205
0.072 0.086 0.099 0.115 0.134 0.144 0.145 0.144 0.145
MATERIAL
HARDNESS HRc 60 ~ HRc 65
DIAMETER RPM FEED Vc Fz
HARDENED STEELS
RPM = rev./min.FEED = mm/min.
1278095808000759056904550380028502280
27602500237024602130196016401230980
120 120 125 145 145 145 145 145 145
0.072 0.087 0.099 0.108 0.125 0.144 0.144 0.144 0.143
HRc 65 ~ HRc 70
RPM FEED Vc Fz
37•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
CARBIDE, 4 FLUTE BALL NOSE
G8D62 SERIESG8A28, G8A38, G8A53 SERIES
CARBIDE, 2 FLUTE BALL NOSE
RPM = rev./min.FEED = mm/min.
0.05D
0.02D
0.05D
0.02D
0.05D
0.02D
R0.1 ×0.2R0.15 ×0.3R0.2 ×0.4R0.25 ×0.5R0.3 ×0.6R0.4 ×0.8R0.5 ×1.0R0.6 ×1.2R0.75 ×1.5R1.0 ×2.0R1.5 ×3.0R2.0 ×4.0R2.5 ×5.0R3.0 ×6.0R4.0 ×8.0R5.0 ×10.0R6.0 ×12.0R8.0 ×16.0R10.0 ×20.0
5000050000500005000050000500005000050000500004970033100249001860013900111009300695055704450
1200150019002400290039004800510054005700600060005800485042003700295026502350
30 45 65 80 95 125 155 190 235 310 310 315 290 260 280 290 260 280 280
0.012 0.015 0.019 0.024 0.029 0.039 0.048 0.051 0.054 0.057 0.091 0.120 0.156 0.174 0.189 0.199 0.212 0.238 0.264
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS HARDENED STEELS
5000050000500005000050000500005000048000480004780031800239001780013400107008900668053504300
1050135017002100250033004200430045004800530053004900410035003100250022001950
30 45 65 80 95 125 155 180 225 300 300 300 280 255 270 280 250 270 270
0.011 0.014 0.017 0.021 0.025 0.033 0.042 0.045 0.047 0.050 0.083 0.111 0.138 0.153 0.164 0.174 0.187 0.206 0.227
HRc 40 ~ HRc 50
RPM FEED Vc Fz
450004500045000450004500045000450004300043000400002650020000150001100090007500560045003600
960120015001900220030003800385040004000400040003750310027002400190017001500
30 40 55 70 85 115 140 160 205 250 250 250 235 205 225 235 210 225 225
0.011 0.013 0.017 0.021 0.024 0.033 0.042 0.045 0.047 0.050 0.075 0.100 0.125 0.141 0.150 0.160 0.170 0.189 0.208
HRc 50 ~ HRc 55
RPM FEED Vc Fz
0.05D
0.02D
R0.1 ×0.2R0.15 ×0.3R0.2 ×0.4R0.25 ×0.5R0.3 ×0.6R0.4 ×0.8R0.5 ×1.0R0.6 ×1.2R0.75 ×1.5R1.0 ×2.0R1.5 ×3.0R2.0 ×4.0R2.5 ×5.0R3.0 ×6.0R4.0 ×8.0R5.0 ×10.0R6.0 ×12.0R8.0 ×16.0R10.0 ×20.0
400004000040000400004000040000400003800037000350002350017500135001000080006600500040003200
77096512001500180024003000300031003150315031503050250021501900155013501200
25 40 50 65 75 100 125 145 175 220 220 220 210 190 200 205 190 200 200
0.010 0.012 0.015 0.019 0.023 0.030 0.038 0.039 0.042 0.045 0.067 0.090 0.113 0.125 0.134 0.144 0.155 0.169 0.188
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
HARDENED STEELS
35000350003500035000350003500035000340003300032000210001600011500880070005800440035002800
6748401050130016002100260027002700280028002800255021501850165012501000800
20 35 45 55 65 90 110 130 155 200 200 200 180 165 175 180 165 175 175
0.010 0.012 0.015 0.019 0.023 0.030 0.037 0.040 0.041 0.044 0.067 0.088 0.111 0.122 0.132 0.142 0.142 0.143 0.143
HRc 60 ~ HRc 65
RPM FEED Vc Fz
31500315003150031500315003150035000306002970028500190001450010500800065005300400032002550
57070089011001400180023002300230023002300230021001750155013801050850660
20 30 40 50 60 80 110 115 140 180 180 180 165 150 165 165 150 160 160
0.009 0.011 0.014 0.017 0.022 0.029 0.033 0.038 0.039 0.040 0.061 0.079 0.100 0.109 0.119 0.130 0.131 0.133 0.129
HRc 65 ~ HRc 70
RPM FEED Vc Fz
R1.5 × 3.0R2.0 × 4.0R2.5 × 5.0R3.0 × 6.0R4.0 × 8.0R5.0 × 10.0R6.0 × 12.0R8.0 × 16.0R10.0 × 20.0
361002705021600180401353010840902067705450
1020087007800732062705560523039103140
340 340 340 340 340 340 340 340 340
0.071 0.080 0.090 0.101 0.116 0.128 0.145 0.144 0.144
MATERIAL
HARDNESS HRc 30 ~ HRc 45
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS HARDENED STEELS
30250226501782015180113309130759056704570
730063505750556046804070380029202310
285 285 280 285 285 285 285 285 285
0.060 0.070 0.081 0.092 0.103 0.111 0.125 0.129 0.126
HRc 45 ~ HRc 55
RPM FEED Vc Fz
2444018300146501221091907370611046203690
488044004150402035203080281022001760
230 230 230 230 230 230 230 230 230
0.050 0.060 0.071 0.082 0.096 0.104 0.115 0.119 0.119
HRc 55 ~ HRc 60
RPM FEED Vc Fz
R1.5 × 3.0R2.0 × 4.0R2.5 × 5.0R3.0 × 6.0R4.0 × 8.0R5.0 × 10.0R6.0 × 12.0R8.0 × 16.0R10.0 × 20.0
2228016710133701111083106660556041803300
401036803590341029702530215016001270
210 210 210 210 210 210 210 210 205
0.045 0.055 0.067 0.077 0.089 0.095 0.097 0.096 0.096
MATERIAL
HARDNESS HRc 60 ~ HRc 65
DIAMETER RPM FEED Vc Fz
HARDENED STEELS
RPM = rev./min.FEED = mm/min.
15170113809100759056704570380028602260
24302280226022001870176014301100880
145 145 145 145 145 145 145 145 140
0.040 0.050 0.062 0.072 0.082 0.096 0.094 0.096 0.097
HRc 65 ~ HRc 70
RPM FEED Vc Fz
39•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A60 SERIES
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING - SLOTTING CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING - SIDE CUTTING
G8A60 SERIES
RPM = rev./min.FEED = mm/min.
D
0.02D0.03D
D
0.03D
D
0.50.60.81.02.03.04.05.06.08.010.012.0
500005000050000480003330021800167001570013100988078006650
144185235590670670700810755740670672
80 95 125 150 210 205 210 245 245 250 245 250
0.001 0.002 0.002 0.006 0.010 0.015 0.021 0.026 0.029 0.037 0.043 0.051
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
450004500040000380002600017300132001250010350780061505250
110140170460540540560645615575540540
70 85 100 120 165 165 165 195 195 195 195 200
0.001 0.002 0.002 0.006 0.010 0.016 0.021 0.026 0.030 0.037 0.044 0.051
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
400004000030000255001750011500880083006900520041003500
85110115285335335350395385355330330
65 75 75 80 110 110 110 130 130 130 130 130
0.001 0.001 0.002 0.006 0.010 0.015 0.020 0.024 0.028 0.034 0.040 0.047
HRc 50 ~ HRc 55
RPM FEED Vc Fz
D
0.02D
0.50.60.81.02.03.04.05.06.08.010.012.0
33000300002500020500145009500720064005300400032002650
556570170205205215230225205190190
50 55 65 65 90 90 90 100 100 100 100 100
0.001 0.001 0.001 0.004 0.007 0.011 0.015 0.018 0.021 0.026 0.030 0.036
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
25000250001900016000110007500560051004200320025502100
304045105130130135145140130120120
40 45 50 50 70 70 70 80 80 80 80 80
0.001 0.001 0.001 0.003 0.006 0.009 0.012 0.014 0.017 0.020 0.024 0.029
HRc 60 ~ HRc 65
RPM FEED Vc Fz
HARDENED STEELS
2000020000160001250095006400475044503700280022001860
20252870909095105100959090
30 40 40 40 60 60 60 70 70 70 70 70
0.250 0.278 0.280 0.700 0.643 0.643 0.679 0.656 0.625 0.594 0.563 0.563
HRc 65 ~ HRc 70
RPM FEED Vc Fz
RPM = rev./min.FEED = mm/min.
0.50.60.81.02.03.04.05.06.08.010.012.0
500005000050000480003330021800167001570013100988078006650
2052653358409609601000116010801056960960
80 95 125 150 210 205 210 245 245 250 245 250
0.002 0.003 0.003 0.009 0.014 0.022 0.030 0.037 0.041 0.053 0.062 0.072
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
450004500040000380002600017300132001250010350780061505250
160200245656776776800920880824776776
70 85 100 120 165 165 165 195 195 195 195 200
0.002 0.002 0.003 0.009 0.015 0.022 0.030 0.037 0.043 0.053 0.063 0.074
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
400004000030000255001750011500880083006900520041003500
125160165408480480500568552508472472
65 75 75 80 110 110 110 130 130 130 130 130
0.002 0.002 0.003 0.008 0.014 0.021 0.028 0.034 0.040 0.049 0.058 0.067
HRc 50 ~ HRc 55
RPM FEED Vc Fz
0.50.60.81.02.03.04.05.06.08.010.012.0
33000300002500020500145009500720064005300400032002650
8090100248296296308328320292272272
50 55 65 65 90 90 90 100 100 100 100 100
0.001 0.002 0.002 0.006 0.010 0.016 0.021 0.026 0.030 0.037 0.043 0.051
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
25000250001900016000110007500560051004200320025502100
456065152184184192208204188176176
40 45 50 50 70 70 70 80 80 80 80 80
0.001 0.001 0.002 0.005 0.008 0.012 0.017 0.020 0.024 0.029 0.035 0.042
HRc 60 ~ HRc 65
RPM FEED Vc Fz
HARDENED STEELS
2000020000160001250095006400475044503700280022001860
303540100132132136152148136128128
30 40 40 40 60 60 60 70 70 70 70 70
0.001 0.001 0.001 0.004 0.007 0.010 0.014 0.017 0.020 0.024 0.029 0.034
HRc 65 ~ HRc 70
RPM FEED Vc Fz
40 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] 41•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A52 SERIES
CARBIDE, 2 FLUTE CORNER RADIUS for RIB PROCESSING CARBIDE, 2 FLUTE MINIATURE CORNER RADIUS - SLOTTING
G8A50 SERIES
RPM = rev./min.FEED = mm/min.
RPM = rev./min.FEED = mm/min.
0.50.60.81.01.21.52.0
25650~3300020900~3520016150~2640012300~1870010450~176009100~176006350~10550
370~470330~560360~590350~540350~590430~830340~570
0.0056~0.03500.0063~0.02940.0084~0.03920.0105~0.02800.0245~0.07000.0161~0.07700.0210~0.1400
40~5239~6641~6639~5939~6643~8340~66
0.029~0.0280.032~0.0320.045~0.0450.057~0.0580.067~0.0670.095~0.0940.107~0.108
MATERIAL
HARDNESS HRc 30 ~ HRc 45
DIAMETER RPM FEED ap(mm) Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
HRc 45 ~ HRc 55
HARDENED STEELS
23750~2600019900~2200015200~1670010500~115009100~100007000~80006100~6700
285~315260~290280~310250~280250~280250~280270~300
0.0040~0.02500.0450~0.02100.0060~0.02800.0075~0.02000.0150~0.04200.0115~0.05500.0150~0.1000
37~4138~4138~4233~3634~3833~3838~42
0.024~0.0240.026~0.0260.037~0.0370.048~0.0490.055~0.0560.071~0.0700.089~0.090
RPM FEED ap(mm) Vc Fz
0.50.60.81.01.21.52.0
14200~1800011900~155009000~117006300~80505400~70004300~55003600~4700
115~130100~120110~125100~115100~115100~115100~120
0.0024~0.01500.0027~0.01260.0036~0.01680.0045~0.01200.0090~0.02520.0069~0.03300.0090~0.0600
22~2822~2923~2920~2520~2620~2623~30
0.016~0.0140.017~0.0150.024~0.0210.032~0.0290.037~0.0330.047~0.0420.056~0.051
MATERIAL
HARDNESS
DIAMETER
HRc 55 ~ HRc 60
HARDENED STEELS
RPM FEED ap(mm) Vc Fz
D
0.05D
0.30.40.50.60.81.01.21.52.0
500005000050000500005000048000420003700033300
190235370470600750790800850
45 65 80 95 125 150 160 175 210
0.002 0.002 0.004 0.005 0.006 0.008 0.009 0.011 0.013
450004500045000450004000038000340003050026000
140180280360440570640670680
40 55 70 85 100 120 130 145 165
0.002 0.002 0.003 0.004 0.006 0.008 0.009 0.011 0.013
400004000040000400003000025500225002100017500
115140220285295360380410420
40 50 65 75 75 80 85 100 110
0.001 0.002 0.003 0.004 0.005 0.007 0.008 0.010 0.012
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
HRc 50 ~ HRc 55
RPM FEED Vc Fz
D
0.05D
0.30.40.50.60.81.01.21.52.0
330003300033000300002500020500200001700014500
7090140160185215250250260
30 40 50 55 65 65 75 80 90
0.001 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.009
250002500025000250001900016000145001300011000
405585105110135145155160
25 30 40 45 50 50 55 60 70
0.001 0.001 0.002 0.002 0.003 0.004 0.005 0.006 0.007
MATERIAL
HARDNESS
DIAMETER
HRc 55 ~ HRc 60
RPM FEED Vc Fz
HARDENED STEELS
HRc 60 ~ HRc 65
RPM FEED Vc Fz
43•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A47, G8B08 SERIES
CARBIDE, 4 FLUTE CORNER RADIUS CARBIDE, 2 FLUTE for RIB PROCESSING
G8A45 SERIES
0.03D
D
0.03D
D
RPM = rev./min.FEED = mm/min.
1.02.03.04.05.06.08.010.012.016.020.0
48000333002180016700157001310098807800665049003900
11841400140014401600156015041400140012001040
150 210 205 210 245 245 250 245 250 245 245
0.006 0.011 0.016 0.022 0.025 0.030 0.038 0.045 0.053 0.061 0.067
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
38000260001730013200125001035078006150525039003100
84010001000104012001120108010081008880776
120 165 165 165 195 195 195 195 200 195 195
0.006 0.010 0.014 0.020 0.024 0.027 0.035 0.041 0.048 0.056 0.063
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
25500175001150088008300690052004100350026002050
568672672704800760720672672584520
80 110 110 110 130 130 130 130 130 130 130
0.006 0.010 0.015 0.020 0.024 0.028 0.035 0.041 0.048 0.056 0.063
HRc 50 ~ HRc 55
RPM FEED Vc Fz
1.02.03.04.05.06.08.010.012.016.020.0
2050014500950072006400530040003200265020001600
344416416432464448416384384336304
65 90 90 90 100 100 100 100 100 100 100
0.004 0.007 0.011 0.015 0.018 0.021 0.026 0.030 0.036 0.042 0.048
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
1600011000750056005100420032002550210016001300
216256256268296280264248240216200
50 70 70 70 80 80 80 80 80 80 80
0.003 0.006 0.009 0.012 0.015 0.017 0.021 0.024 0.029 0.034 0.038
125009500640047504450370028002200186014001100
140184184192216208192176176160144
40 60 60 60 70 70 70 70 70 70 70
0.700 0.657 0.657 0.686 0.675 0.650 0.600 0.550 0.550 0.500 0.450
HRc 60 ~ HRc 65
RPM FEED Vc Fz
HARDENED STEELS
HRc 65 ~ HRc 70
RPM FEED Vc Fz
RPM = rev./min.FEED = mm/min.
0.20.3 0.4 0.5 0.6 0.8 1.0 1.2 1.5 2.0 3.0 4.0
5000043000~5000031400~5000025650~3300020900~3520016150~2640012300~1870010450~176009100~176006350~105504300~70503200~5300
300~350330~420350~590370~470330~560360~590350~540350~590430~830340~570550~900400~675
0.006~0.0160.006~0.0150.005~0.0280.006~0.0350.007~0.0300.009~0.0400.011~0.0280.025~0.0700.017~0.0770.021~0.1400.056~0.2100.074~0.280
3141~4739~6340~5239~6641~6639~5939~6643~8340~6641~6640~67
0.003~0.0040.004~0.0040.006~0.0060.007~0.0070.008~0.0080.011~0.0110.014~0.0140.017~0.0170.024~0.0240.027~0.0270.064~0.0640.063~0.064
MATERIAL
HARDNESS HRc 30 ~ HRc 45
DIAMETER RPM FEED ap(mm) Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
HRc 45 ~ HRc 55
RPM FEED ap(mm) Vc Fz
HARDENED STEELS
5000039900~4620030500~3520023750~2600019900~2200015200~1670010500~115009100~100007000~80006100~67003990~46003000~3400
265~310265~310295~340285~315260~290280~310250~280250~280250~280270~300445~515335~380
0.005~0.0130.004~0.0110.003~0.0200.004~0.0250.005~0.0210.006~0.0280.008~0.0200.015~0.0420.012~0.0550.015~01000.040~0.1500.053~0.200
3138~4438~4437~4138~4138~4233~3634~3833~3838~4238~4338~43
0.003~0.0030.003~0.0030.005~0.0050.006~0.0060.007~0.0070.009~0.0090.012~0.0120.014~0.0140.018~0.0180.022~0.0220.056~0.0560.056~0.056
0.20.3 0.4 0.5 0.6 0.8 1.0 1.2 1.5 2.0 3.0 4.0
5000023900~3230018300~2460014200~1800011900~155009000~117006300~80505400~70004300~55003600~47002400~32001800~2400
225~265105~185120~200115~130100~120110~125100~115100~115100~115100~120105~31075~230
0.005~0.0120.003~0.0070.002~0.0120.003~0.0150.003~0.0130.004~0.0170.005~0.0120.009~0.0260.007~0.0330.009~0.0600.024~0.0900.032~0.120
3123~3023~3122~2822~2923~2920~2520~2620~2623~3023~3023~30
0.002~0.0030.002~0.0030.003~0.0040.004~0.0040.004~0.0040.006~0.0050.008~0.0070.009~0.0080.012~0.010.014~0.0130.022~0.0480.021~0.048
MATERIAL
HARDNESS HRc 55 ~ HRc 65
DIAMETER RPM FEED ap(mm) Vc Fz
HARDENED STEELS
RPM FEED ap(mm) Vc Fz
COPPER
5000048000~5000048000~5000044000~5000037500~5000028500~4700022500~3400022500~3150014500~2500011500~185009000~130006750~9750
455~530550~640790~920800~1150770~1250770~1300810~1300950~1350770~1320770~12501400~21101050~1575
0.010~0.0220.010~0.0250.008~0.0480.010~0.0600.011~0.0510.015~0.0680.018~0.0480.036~0.1010.028~0.1320.036~0.2400.096~0.3600.128~0.480
3145~4760~6369~7971~9472~11871~10785~11968~11872~11685~12385~123
0.005~0.0050.006~0.0060.008~0.0090.009~0.0120.01~0.0130.014~0.0140.018~0.0190.021~0.0210.027~0.0260.033~0.0340.078~0.0810.078~0.081
44 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] 45•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A01, G8A36 SERIES
CARBIDE, 2 FLUTE - SLOTTING CARBIDE, 2 FLUTE - SIDE CUTTING
G8A01, G8A36 SERIES
RPM = rev./min.FEED = mm/min.
D
0.05D
0.03D
D
0.03D
D
0.20.30.40.50.60.80.91.02.03.04.05.06.08.010.012.016.020.0
5000050000500005000050000500004900048000333002180016700157001310098807800665049003900
1301902353704706006557508508508801000950930850850730660
30 45 65 80 95 125 140 150 210 205 210 245 245 250 245 250 245 245
0.001 0.002 0.002 0.004 0.005 0.006 0.007 0.008 0.013 0.019 0.026 0.032 0.036 0.047 0.054 0.064 0.074 0.085
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
4500045000450004500045000400003900038000260001730013200125001035078006150525039003100
115140180280360440520570680680700805770720680680580525
30 40 55 70 85 100 110 120 165 165 165 195 195 195 195 200 195 195
0.001 0.002 0.002 0.003 0.004 0.006 0.007 0.008 0.013 0.020 0.027 0.032 0.037 0.046 0.055 0.065 0.074 0.085
4000040000400004000040000300002780025500175001150088008300690052004100350026002050
95115140220285295330360420420440500480445415415365335
25 40 50 65 75 75 80 80 110 110 110 130 130 130 130 130 130 130
0.001 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.012 0.018 0.025 0.030 0.035 0.043 0.051 0.059 0.070 0.082
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
HRc 50 ~ HRc 55
RPM FEED Vc Fz
D
0.05D
0.20.30.40.50.60.80.91.02.03.04.05.06.08.010.012.016.020.0
330003300033000330003000025000227002050014500950072006400530040003200265020001600
607090140160185205215260260270285280255240240210195
20 30 40 50 55 65 65 65 90 90 90 100 100 100 100 100 100 100
0.001 0.001 0.001 0.002 0.003 0.004 0.005 0.005 0.009 0.014 0.019 0.022 0.026 0.032 0.038 0.045 0.053 0.061
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
330002500025000250002500019000175001600011000750056005100420032002550210016001300
45505585105110125135160160170180180165155155135125
20 25 30 40 45 50 50 50 70 70 70 80 80 80 80 80 80 80
0.001 0.001 0.001 0.002 0.002 0.003 0.004 0.004 0.007 0.011 0.015 0.018 0.021 0.026 0.030 0.037 0.042 0.048
26400200002000020000200001520014000125009500640047504450370028002200186014001100
30354060758090851151151181321301201121129585
15 20 25 30 40 40 40 40 60 60 60 70 70 70 70 70 70 70
0.750 0.700 0.667 0.750 0.833 0.800 0.900 0.850 0.821 0.821 0.843 0.825 0.813 0.750 0.700 0.700 0.594 0.531
HRc 60 ~ HRc 65
RPM FEED Vc Fz
HARDENED STEELS
HRc 65 ~ HRc 70
RPM FEED Vc Fz
RPM = rev./min.FEED = mm/min.
1.02.03.04.05.06.08.010.012.016.020.0
48000333002180016700157001310098807800665049003900
1050120012001250145013501320120012001050950
150 210 205 210 245 245 250 245 250 245 245
0.011 0.018 0.028 0.037 0.046 0.052 0.067 0.077 0.090 0.107 0.122
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
38000260001730013200125001035078006150525039003100
8209709701000115011001030970970840750
120 165 165 165 195 195 195 195 200 195 195
0.011 0.019 0.028 0.038 0.046 0.053 0.066 0.079 0.092 0.108 0.121
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
25500175001150088008300690052004100350026002050
510600600625710690635590590520475
80 110 110 110 130 130 130 130 130 130 130
0.010 0.017 0.026 0.036 0.043 0.050 0.061 0.072 0.084 0.100 0.116
HRc 50 ~ HRc 55
RPM FEED Vc Fz
1.02.03.04.05.06.08.010.012.016.020.0
2050014500950072006400530040003200265020001600
310370370385410400365340340300275
65 90 90 90 100 100 100 100 100 100 100
0.008 0.013 0.019 0.027 0.032 0.038 0.046 0.053 0.064 0.075 0.086
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
1600011000750056005100420032002550210016001300
190230230240260255235220220190175
50 70 70 70 80 80 80 80 80 80 80
0.006 0.010 0.015 0.021 0.025 0.030 0.037 0.043 0.052 0.059 0.067
125009500640047504450370028002200186014001100
125165165170190185170160160140125
40 60 60 60 70 70 70 70 70 70 70
1.250 1.179 1.179 1.214 1.188 1.156 1.063 1.000 1.000 0.875 0.781
HRc 60 ~ HRc 65
RPM FEED Vc Fz
HARDENED STEELS
HRc 65 ~ HRc 70
RPM FEED Vc Fz
47•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8A02, G8A37 SERIES
CARBIDE, 4 FLUTE - SIDE CUTTING CARBIDE, 6 FLUTE 45。HELIX CORNER RADIUS
G8A39 SERIES
※ The Feed, in long & extra long types, should be reduced by around 50%.
0.03D
D
0.03D
D
RPM = rev./min.FEED = mm/min.
RPM = rev./min.FEED = mm/min.
1.02.03.04.05.06.08.010.012.016.020.0
48000333002180016700157001310098807800665049003900
14801750175018002000195018801750175015001300
150 210 205 210 245 245 250 245 250 245 245
0.008 0.013 0.020 0.027 0.032 0.037 0.048 0.056 0.066 0.077 0.083
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
38000260001730013200125001035078006150525039003100
1050125012501300150014001350126012601100970
120 165 165 165 195 195 195 195 200 195 195
0.007 0.012 0.018 0.025 0.030 0.034 0.043 0.051 0.060 0.071 0.078
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
25500175001150088008300690052004100350026002050
7108408408801000950900840840730650
80 110 110 110 130 130 130 130 130 130 130
0.007 0.012 0.018 0.025 0.030 0.034 0.043 0.051 0.060 0.070 0.079
HRc 50 ~ HRc 55
RPM FEED Vc Fz
1.02.03.04.05.06.08.010.012.016.020.0
2050014500950072006400530040003200265020001600
430520520540580560520480480420380
65 90 90 90 100 100 100 100 100 100 100
0.005 0.009 0.014 0.019 0.023 0.026 0.033 0.038 0.045 0.053 0.059
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
1600011000750056005100420032002550210016001300
270320320335370350330310300270250
50 70 70 70 80 80 80 80 80 80 80
0.004 0.007 0.011 0.015 0.018 0.021 0.026 0.030 0.036 0.042 0.048
125009500640047504450370028002200186014001100
175230230240270260240220220200180
40 60 60 60 70 70 70 70 70 70 70
0.875 0.821 0.821 0.857 0.844 0.813 0.750 0.688 0.688 0.625 0.563
HRc 60 ~ HRc 65
RPM FEED Vc Fz
HARDENED STEELS
HRc 65 ~ HRc 70
RPM FEED Vc Fz
0.03D
D
6.08.010.012.016.020.0
24800200001600013000100008000
535055004900450040003350
465 505 505 490 505 505
0.036 0.046 0.051 0.058 0.067 0.070
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
2350019000155001250097007800
490050004500410037003400
445 480 485 470 490 490
0.035 0.044 0.048 0.055 0.064 0.073
HRc 40 ~ HRc 50
RPM FEED Vc Fz
HARDENED STEELS
16000120009500800060004800
490046004100380034003200
300 300 300 300 300 300
0.051 0.064 0.072 0.079 0.094 0.111
HRc 50 ~ HRc 55
RPM FEED Vc Fz
0.03D
D
6.08.010.012.016.020.0
13500100008000660050004000
330031002900250023002100
255 250 250 250 250 250
0.041 0.052 0.060 0.063 0.077 0.088
MATERIAL
HARDNESS HRc 55 ~ HRc 60
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
1050080006400530040003200
210020001800160012501020
200 200 200 200 200 200
0.033 0.042 0.047 0.050 0.052 0.053
HRc 60 ~ HRc 65
RPM FEED Vc Fz
HARDENED STEELS
800060004800400030002400
1450140013001150870690
150 150 150 150 150 150
1.208 1.167 1.083 0.958 0.725 0.575
HRc 65 ~ HRc 70
RPM FEED Vc Fz
48 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected] 49•phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:[email protected]
G8D63 SERIES
CARBIDE, 6&8 FLUTE 45。HELIX LONG LENGTH CARBIDE, 6&8 FLUTE 45。HELIX EXTRA LONG LENGTH
G8D64 SERIES
RPM = rev./min.FEED = mm/min.
RPM = rev./min.FEED = mm/min.
0.01D
1.5D
0.04D
1.5D
6.08.010.012.014.016.018.020.025.0
636048003840324027302400212019201560
150015101450135513201300161012101370
120 120 120 120 120 120 120 120 125
0.039 0.052 0.063 0.070 0.081 0.090 0.095 0.079 0.110
504038403000252021801920170015601200
1045107099593592091010901130925
95 95 95 95 95 95 95 100 95
0.035 0.046 0.055 0.062 0.070 0.079 0.080 0.091 0.096
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
HRc 40 ~ HRc 55
RPM FEED Vc Fz
HARDENED STEELS
0.04D
1.5D
6.08.010.012.014.016.018.020.025.0
38402880228019201600144012801200960
720720685650630625750660670
70 70 70 70 70 70 70 75 75
0.031 0.042 0.050 0.056 0.066 0.072 0.073 0.069 0.087
25201920156013201070960850720610
430430420395325370450410385
50 50 50 50 45 50 50 45 50
0.028 0.037 0.045 0.050 0.051 0.064 0.066 0.071 0.079
MATERIAL
HARDNESS HRc 55 ~ HRc 65
DIAMETER RPM FEED Vc Fz
HRc 65 ~ HRc 70
RPM FEED Vc Fz
HARDENED STEELS
6.08.010.012.014.016.018.020.025.0
3180239019101580137011901070960770
770720685660620575730660550
60 60 60 60 60 60 60 60 60
0.040 0.050 0.060 0.070 0.075 0.081 0.085 0.086 0.089
MATERIAL
HARDNESS HRc 30 ~ HRc 40
DIAMETER RPM FEED Vc Fz
ALLOY STEELSHEAT RESISTANT STEELS
3180239019101580137011901070960770
575575575575540505685695490
60 60 60 60 60 60 60 60 60
0.030 0.040 0.050 0.061 0.066 0.071 0.080 0.090 0.080
HRc 40 ~ HRc 55
RPM FEED Vc Fz
HARDENED STEELS
25401910152012701090960850770610
455455455455430410550560395
50 50 50 50 50 50 50 50 50
0.030 0.040 0.050 0.060 0.066 0.071 0.081 0.091 0.081
HRc 55 ~ HRc 65
RPM FEED Vc Fz