43
YuYao Yugao Plastic Mould Co., LTD Skype: tonny—lee Email: [email protected] Web: www.yugaomould.com
YuYao Yugao Plastic Mould Co., LTDSkype: tonny—leeEmail: [email protected]: www.yugaomould.com
C265 C266 part is Audi Q3 B Pillar decorate plate. The firstmolding is ABS，the second time molding is PMMA. The followingis the Cavity first molding and second molding.
PMMA ABS
Core and cavity material:M303
High Gloss Mould
The first time is ABS plastic
The second moldingPMMA plastic.
C265 C266 part is Audi Q3 B pillar decorate plate. The firstmolding is ABS plastic，the second molding is PMMA plastic.
Mould on ENGEL_duo900WP machine
First inject isABS, sequence hotrunner molding
Second inject isPMMA,common hotrunner molding
Two same core
Inject ABS oncavity
Inject PMMAcavityAfter finish inject ABS, two
cores rotate 180°withmachine, then inject PMMA.
SANTANA-NF-Gloss B pillar
Part plastic：PMMA Cavity and Core:1.2343(Plating surface）
SANTANA-NF-Gloss B pillar
Auto lamps Mould
VALEO LAMPS
Material：PPT40 Cavity and core:1.2711
VALEO LAMPS
Valeo LAMPS
Plastic：PC Cavity and Core:1.2343
Valeo lampls
IMD Mould
RENAULT part，IMD molding
Plastic：ABS PC Cavity and core:1.2343
RENAULT part，IMD molding
Volvo S60 center console panel,IMD molding
Plastic：PA6GF30 Cavity and core:1.2738
Volvo S60 center console panel,IMD molding
B8PA Interior ,IMD molding
Plastic:PA6 GF35：Cavity and core:NAK80
B8PA Interior,IMD molding
Double Color Mould
Car Spoiler, double color molding
Cavity and core:P20
PP TD20
TPE
Car Spoiler, double color molding
B753 windscreens retaining bar,double color molding
Plastic：PPGF30 + TPE Cavity and core:1.2738H
TPE
PPGF30
B753 windscreens retaining bar,double color molding
Interior and exterior trim mould
Car Mould
Plastic：PPC Cavity and core:718
Car Mould
Renault Panel
Plastic：PE Cavity and core:1.2738
Renault Panel
Renault Panel
Car Mould ，Child Chair
Plastic：PP Cavity and core:718H
Car Mould ，Child Chair
SANTANA Door
Plastic: PP Cavity:718 Core：P20
SANTANA Door
SANTANA Door
NISSAN Grill
Plastic ：2738HH Cavity and core :ASA
NISSAN Grill
NISSAN Grill
RENAULT DRAWER LID
Plastic：2738 Cavity and core:P/E EPDM T15
RENAULT DRAWER LID
Peugeot Part
Plastic：2738 Cavity and core:PP GFHM 40
Peugeot Part
Spare parts and steel are purchased from at home and abroad , thesteel suppler are:Aubert&duval,Assab, HitachiMetals,Bohler,Buderus,Schmiedwerke Grodits
Purchase
Mould base and stander d partssuppliers: LKM，HASCO，LKMRABOUDIN
PurchaseThe hot runner suppliers: HRSMOLDMASTER,Synventivec,YUDO, HASCO,ORMYO,Runipsys
