FC-40 Plus Series - IndustryNet

The FC-40 Plus Feeder Cube isa single controller, housed in aNema-1 general purposeenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.

FC-40 Plus SeriesFC-40 Plus — 121-000-0880

FC-40 Plus Series "All Purpose" Feeder Cube®Controllers

FC-40 Plus Series Typical Applications Vibratory bowlsStorage hoppersLinear inline feeders

Most models are UL and cUL listed (File EI83233)Provides a soft-start adjustment so a feederbowl, inline track drive or storage hopper cancycle on gently.Maximum output power level adjustment allowsfor the maximum output of the control to bepresetOutput is switch selectable from 120 pulses persecond (UN-rectified or full-wave) to 60 pulsesper second (rectified or half-wave)Line voltage compensation featureautomatically adjusts the output of thecontroller to compensate for incoming voltagefluctuationsEasily integrates with PLC's for remote controlaccessFor additional features, please refer to theAdvanced Application Note

Toll Free US & Canada 800.562.1868 | Fax 815.316.4701 | Email [email protected] — Rodix, Inc.— Page 1

The FC-41 Plus Feeder Cube isa single controller, housed in aNema-12 oil resistantenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.






The FC-41H Plus Feeder Cubeis a single heavy-dutycontroller housed in a Nema-12oil resistant enclosure. It hasbeen redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Fused for 30 amps.

FC-40 Plus SeriesFC-41H Plus — 121-000-0882





The FC-42 Plus Feeder Cube isa dual controller, housed in aNema-1 general purposeenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Unit A is fused for 10 amps;Unit B is fused for 5 amps.






The FC-43 Plus Feeder Cube isa dual controller, housed in aNema-12 oil resistantenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Both Unit A and Unit B arefused for 15 amps.






The FC-43H Plus Feeder Cubeis a dual heavy-duty controllerhoused in a Nema-12 oilresistant enclosure. It hasbeen redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Unit A is fused for 30 amps;Unit B is fused for 15 amps.






The FC-44 Plus Feeder Cube isa single open frame controllerfor mounting on an electricalpanel. It has been redesignedto now include the features ofthe FC-40-PLC Plus Seriesincluding line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.(Potentiometer and switch notincluded).






The FC-45 Plus Feeder Cube isa single open frame controllerfor mounting on an electricalpanel. It has been redesignedto now include the features ofthe FC-40-PLC Plus Seriesincluding line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.Potentiometer and switchincluded.






The FC-47 Plus Feeder Cube isa single open frame controllerfor mounting on the inside ofan electrical enclosure door. Ithas been redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.Potentiometer and switchincluded.






The FC-48 Plus Feeder Cube isa single controller housed in aNema-12 oil resistantenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.






The FC-48H Plus Feeder Cubeis a single heavy-dutycontroller housed in a Nema-12oil resistant enclosure. It hasbeen redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Fused for 15 amps.






The FC-49 Plus Feeder Cube isa dual controller housed in aNema-12 oil resistantenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60Hz.Unit A and Unit B are bothfused for 8 amps.






The FC-49H Plus Feeder Cubeis a dual heavy-duty controllerhoused in a Nema-12 oilresistant enclosure. It hasbeen redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 15 amps;Unit B is fused for 8 amps.






The FC-100 Plus Feeder Cube isa triple controller housed in aNema-1 general purposeenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Unit A fused for 10 amps; UnitB fused for 15 amps; Unit Cfused for 5 amps.






The FC-101 Plus Feeder Cube isa triple controller housed in aNema-12 oil resistantenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Units A, B and C are all fusedfor 15 amps.






The FC-108 Plus Feeder Cube isa triple controller housed in aNema-12 oil resistantenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Units A, B and C are all fusedfor 8 amps.






The FC-44-240 Plus FeederCube is a single open framecontroller for mounting on anelectrical panel. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.(Potentiometer and switch notincluded).

FC-40 Plus SeriesFC-44-240 Plus — 121-000-0896





The FC-45-240 Plus FeederCube is a single open framecontroller for mounting on anelectrical panel. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.Potentiometer and switchincluded.






The FC-47-240 Plus FeederCube is a single open framecontroller for mounting on theinside of an electricalenclosure door. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.Potentiometer and switchincluded.







The FC-101H Plus Feeder Cubeis a triple heavy-dutycontroller housed in a Nema-12oil resistant enclosure. It hasbeen redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Unit A fused 15 amps; Unit Bfused 30 amps; Unit C fused 15amps.






The FC-108H Plus Feeder Cubeis a triple heavy-dutycontroller housed in a Nema-12oil resistant enclosure. It hasbeen redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Unit A fused 8 amps; Unit Bfused 15 amps; Unit C fused 8amps.






The FC-40 Plus Feeder Cubewith 5 turn pot is a singlecontroller, housed in a Nema-1general purpose enclosure. Ithas been redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. A 5turn main control pot isinstalled for finer speedcontrol. Input voltage is120VAC, 50/60 Hz. Fused for15 amps.

FC-40 Plus SeriesFC-40 Plus 5-Turn — 121-000-0901






The FC-41 Plus Feeder Cubewith 5 turn pot is a singlecontroller, housed in aNema-12 oil resistantenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. A 5turn main control pot isinstalled for finer speedcontrol. Input voltage is120VAC, 50/60 Hz. Fused for15 amps.

FC-40 Plus SeriesFC-41 Plus 5-Turn — 121-000-0904






The FC-40-240 Plus FeederCube is a single controller,housed in a Nema-1 generalpurpose enclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.






The FC-42-240 Plus FeederCube is a dual controller,housed in a Nema-1 generalpurpose enclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 8 amps; UnitB is fused for 5 amps.






The FC-100-240 Plus FeederCube is a triple controllerhoused in a Nema-1 generalpurpose enclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Unit A fused for 5 amps; Unit Bfused for 8 amps; Unit C fusedfor 2 amps.






The FC-40-240 Plus FeederCube with 5 turn pot is a singlecontroller, housed in a Nema-1general purpose enclosure. Ithas been redesigned to nowinclude the features of theFC-40-PLC Plus Series includingline voltage compensation andalternate methods of remotelycontrolling the output. A 5turn main control pot isinstalled for finer speedcontrol. Input voltage is240VAC, 50/60 Hz. Fused for 8amps.

FC-40 Plus SeriesFC-40-240 Plus with 5 turn pot —121-000-8797






The FC-40-Q Plus Feeder Cubeis a quad controller housed ina Nema-1 general purposeenclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 120VAC, 50/60 Hz.Unit A fused for 5 amps; Unit Bfused for 8 amps; Units C andD are fused for 1 amp. NOT ULLISTED.

FC-40 Plus SeriesFC-40-Q — 121-000-8820






The FC-40-Q-240 Plus FeederCube is a quad controllerhoused in a Nema-1 generalpurpose enclosure. It has beenredesigned to now include thefeatures of the FC-40-PLC PlusSeries including line voltagecompensation and alternatemethods of remotelycontrolling the output. Inputvoltage is 240VAC, 50/60 Hz.Unit A fused for 5 amps; Unit Bfused for 8 amps; Units C andD are fused for 1 amp. NOT ULLISTED.

FC-40 Plus SeriesFC-40-Q-240 — 121-000-8825





121-000-8825

121-000-8825

The FC-75-240 Plus FeederCube is a single, open frame 70Series controller designed forinstalling on the door of anelectrical enclosure or can bemounted on a DIN rail. It istypically used for small feederbowls, inlines and storagehoppers. Input voltage is240VAC, 50/60 Hz and fusedfor 5 amps. The output voltageis 0-240VAC. NOT UL LISTED.

FC-70 SeriesFC-75-240 Plus — 121-000-1107

FC-70 Series "Light Duty"Feeder Cube®Controllers

FC-70 Series Typical ApplicationsSmall Vibratory bowlsStorage hoppersLinear inline feeders

Run interlock interrupt jumperOutput is switch selectable from 120 pulses persecond (UN-rectified or full-wave) to 60 pulsesper second (rectified or half-wave).Logarithmic tapered potentiometer allows forfine speed control adjustment.Soft start.Line voltage compensation.


The FC-70-240 Feeder Cube isa single controller in a generalpurpose enclosure designed foruse with small vibartory bowlsthat do not require a partssensor, inline track drives andstorage hoppers. Input voltageis 240VAC (Operating range190VAC - 250VAC). Output is 0- 240VAC and is fused for 5amps. NOT UL LISTED.

FC-70 SeriesFC-70-240 Plus — 121-000-1108





The FC-70 Plus Feeder Cube isa single controller, housed in aNema-1 general purposeenclosure and replaces theobsolete FC-70, 121-000-0036.It has been redesigned and isnow a microprocessor basedcontroller with new featuressuch as soft start and linevoltage compensation. Inputvoltage is 120VAC, 50/60 Hz.Fused for 5 amps. NOT ULLISTED.

FC-70 SeriesFC-70 Plus — 121-000-1109





The FC-75 Plus Feeder Cube isa single, open frame 70 Seriescontroller designed forinstalling on the door of anelectrical enclosure or can bemounted on a DIN rail. It istypically used for small feederbowls, inlines and storagehoppers. Input voltage is120VAC, 50/60 Hz and fusedfor 5 amps. The output voltageis 0-120VAC. This is a directreplacement for the obsoleteFC-75, 121-000-0040. NOT ULLISTED.

FC-70 SeriesFC-75 Plus — 121-000-1110






The FC-71 Plus Feeder Cube isa low cost single controllerhoused in a Nema-12 oilresistant enclosure. Inputvoltage is 120VAC, 50/60Hz.Fused for 5 amps. NOT ULLISTED.

FC-70 SeriesFC-71 Plus — 121-000-1112





The FC-70H Plus Feeder Cubeis a single, general purpose,low cost controller for use withsmaller bowls, inlines andhoppers. It has beenredesigned and now featuresline voltage compensation, softstart and additional options forremote operation. Inputvoltage is 120VAC, 50/60 Hz.The output is fused for 10amps. This unit directlyreplaces the obsolete FC-70H,121-000-0038. NOT UL LISTED

FC-70 SeriesFC-70H Plus — 121-000-1113





The FC-90 Plus Feeder Cube isa single controller with partssensing, housed in a Nema-1general purpose enclosure.Input voltage is 120VAC, 50/60Hz. Fused for 15 amps.


FC-90 Plus Series "Parts Sensing" Feeder Cube®Controllers

FC-90 Plus Series Typical Applications Vibratory bowls that require part sensingStorage hoppers using photoelectric bowllevel detectors

Most models are UL and cUL listed (File EI83233)Provides a soft-start adjustment so a feederbowl, inline track drive or storage hopper cancycle on gently.Maximum output power level adjustment allowsfor the maximum output of the control to bepreset.Output is switch selectable from 120 pulses persecond (UN-rectified or full-wave) to 60 pulsesper second (rectified or half-wave).Line voltage compensation featureautomatically adjusts the output of thecontroller to compensate for incoming voltagefluctuations.12vdc power supply provided along withseparate on and off time delays for the partssensor (NPN or PNP).Auxiliary output provided for interlocking withother Rodix controlsA Constant Feed Rate (CFR) sensor can be


installed to automatically adjust the output ofthe control based on the vibration level of thefeeder.


The FC-90-2 Plus Feeder Cubeis a dual controller with twopart sensing units, housed in aNema-1 general purposeenclosure. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 5 amps.








The FC-90-3 Plus Feeder Cubeis a triple controller with threepart sensing units, housed in aNema-1 general purposeenclosure. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 15 amps; Unit C isfused for 5 amps.








The FC-97 Plus Feeder Cube isa single open frame controllerwith parts sensing formounting on the inside of anelectrical enclosure door.Input voltage is 120VAC, 50/60Hz. Fused for 15 amps.Potentiometer and switchincluded.








The FC-94 Plus Feeder Cube isa single open frame controllerwith parts sensing formounting on an electricalpanel. Input voltage is 120VAC,50/60 Hz. Fused for 15 amps.(Potentiometer and switch notincluded).








The FC-95 Plus Feeder Cube isa single open frame controllerwith parts sensing formounting on an electricalpanel. Input voltage is 120VAC,50/60 Hz. Fused for 15 amps.Potentiometer and switchincluded.








The FC-91 Plus Feeder Cube isa single controller with partssensing, housed in a Nema-12oil resistant enclosure. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.








The FC-91-2 Plus Feeder Cubeis a dual controller with twoparts sensing units, housed in aNema-12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 15amps.








The FC-91-3 Plus Feeder Cubeis a triple controller with threeparts sensing units, housed in aNema-12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. Unit A, UnitB and Unit C are all fused for15 amps.








The FC-91H Plus Feeder Cubeis a single heavy-dutycontroller with parts sensinghoused in a Nema-12 oilresistant enclosure. Inputvoltage is 120VAC, 50/60 Hz.Fused for 30 amps.








The FC-91-2H Plus Feeder Cubeis a dual heavy-duty controllerwith two parts sensing unitshoused in a Nema-12 oilresistant enclosure. Inputvoltage is 120VAC, 50/60 Hz.Unit A is fused for 30 amps;Unit B is fused for 15 amps.

FC-90 Plus SeriesFC-91-2H Plus — 121-000-8300







The FC-97-240 Plus FeederCube is a single open framecontroller with parts sensingfor mounting on the inside ofan electrical enclosure door.Input voltage is 240VAC, 50/60Hz. Fused for 8 amps.Potentiometer and switchincluded.








The FC-94-240 Plus FeederCube is a single open framecontroller with parts sensingfor mounting on an electricalpanel. Input voltage is 240VAC,50/60 Hz. Fused for 8 amps.(Potentiometer and switch notincluded).








The FC-95-240 Plus FeederCube is a single open framecontroller with parts sensingfor mounting on an electricalpanel. Input voltage is 240VAC,50/60 Hz. Fused for 8 amps.Potentiometer and switchincluded.








The FC-98 Plus Feeder Cube isa single controller with partssensing, housed in a Nema-12oil resistant enclosure. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.








The FC-98-2 Plus Feeder Cubeis a dual controller with twoparts sensing units, housed in aNema-12 oil resistantenclosure. Input voltage is240VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 8amps.








The FC-98-3 Plus Feeder Cubeis a triple controller with threeparts sensing units, housed in aNema-12 oil resistantenclosure. Input voltage is240VAC, 50/60 Hz. Unit A, UnitB and Unit C are all fused for 8amps.








The FC-98H Plus Feeder Cubeis a single heavy-dutycontroller with parts sensinghoused in a Nema-12 oilresistant enclosure. Inputvoltage is 240VAC, 50/60 Hz.Fused for 15 amps.








The FC-98-2H Plus Feeder Cubeis a dual heavy-duty controllerwith two parts sensing unitshoused in a Nema-12 oilresistant enclosure. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 15 amps;Unit B is fused for 8 amps.

FC-90 Plus SeriesFC-98-2H Plus — 121-000-8380







The FC-90-4 Plus Feeder Cubeis a single controller with partssensing, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled. Input voltage is120VAC, 50/60 Hz. Fused for15 amps.








The FC-90-5 Plus Feeder Cubeis a single controller with partssensing, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled and (2) 111-52 fiberoptic cables. Input voltage is120VAC, 50/60 Hz. Fused for15 amps.








The FC-91-4 Plus Feeder Cubeis a single controller with partssensing, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled. Input voltage is120VAC, 50/60 Hz. Fused for15 amps.








The FC-91-5 Plus Feeder Cubeis a single controller with partssensing, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Male and femalepower cords installed. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.








The FC-91H-4 Plus Feeder Cubeis a single heavy-dutycontroller with parts sensinghoused in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled. Input voltage is120VAC, 50/60 Hz. Fused for30 amps.

FC-90 Plus SeriesFC-91H-4 Plus — 121-000-8430







The FC-91H-5 Plus Feeder Cubeis a single heavy-dutycontroller with parts sensinghoused in a Nema-12 oilresistant enclosure with111-500 optic sensor installed,(2) 111-31 fiber optic cablesand incoming and outgoingpower cords (plugs notincluded). Input voltage is120VAC, 50/60 Hz. Fused for30 amps.








The FC-92 Plus Feeder Cube isa dual controller, housed in aNema-1 general purposeenclosure with parts sensing.Input voltage is 120VAC, 50/60Hz. Unit A is fused for 10 amps;Unit B is fused for 5 amps.








The FC-92-4 Plus Feeder Cubeis a dual controller, housed ina Nema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed. Inputvoltage is 120VAC, 50/60 Hz.Unit A is fused for 10 amps;Unit B is fused for 5 amps.








The FC-92-5 Plus Feeder Cubeis a dual controller, housed ina Nema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed and (2)111-52 fiber optic cables. Inputvoltage is 120VAC, 50/60 Hz.Unit A is fused for 10 amps;Unit B is fused for 5 amps.








The FC-93 Plus Feeder Cube isa dual controller with partssensing, housed in a Nema-12oil resistant enclosure. Inputvoltage is 120VAC, 50/60 Hz.Both Unit A and Unit B arefused for 15 amps.








The FC-93-4 Plus Feeder Cubeis a dual controller, housed ina Nema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed. Inputvoltage is 120VAC, 50/60 Hz.Both Unit A and Unit B arefused for 15 amps.








The FC-93-5 Plus Feeder Cubeis a dual controller, housed ina Nema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables. Inputand output power cordsinstalled. Input voltage is120VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 15amps.








The FC-93H Plus Feeder Cubeis a dual heavy duty controllerwith parts sensing, housed in aNema-12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 30 amps and Unit B isfused for 15 amps.








The FC-93H-4 Plus Feeder Cubeis a dual heavy duty controller,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 30 amps and Unit B isfused for 15 amps.








The FC-93H-5 Plus Feeder Cubeis a dual heavy duty controller,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Includes inputand output power cordsinstalled. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 30 amps and Unit B isfused for 15 amps.








The FC-98-4 Plus Feeder Cubeis a single controller with partssensing, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled. Input voltage is240VAC, 50/60 Hz. Fused for 8amps.








The FC-98-5 Plus Feeder Cubeis a single controller with partssensing, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled, (2) 111-31 fiber opticcables and incoming andoutgoing power cords (plugsnot included). Input voltage is240VAC, 50/60 Hz. Fused for 8amps.








The FC-98H-4 Plus Feeder Cubeis a single heavy-dutycontroller with parts sensinghoused in a Nema-12 oilresistant enclosure with a111-500 optic sensor installed.Input voltage is 240VAC, 50/60Hz. Fused for 15 amps.








The FC-98H-5 Plus Feeder Cubeis a single heavy-dutycontroller with parts sensinghoused in a Nema-12 oilresistant enclosure with111-500 optic sensor installedand (2) 111-31 fiber opticcables. Input voltage is240VAC, 50/60 Hz. Fused for15 amps.








The FC-99 Plus Feeder Cube isa dual controller, housed in aNema-12 oil resistantenclosure with parts sensing.Input voltage is 240VAC, 50/60Hz. Both Unit A and Unit B arefused for 8 amps.








The FC-99-4 Plus Feeder Cubeis a dual controller, housed ina Nema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed. Inputvoltage is 240VAC, 50/60 Hz.Both Unit A and Unit B arefused for 8 amps.








The FC-99-5 Plus Feeder Cubeis a dual controller, housed ina Nema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables.Includes input and outputpower cords. Input voltage is240VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 8amps.








The FC-99H Plus Feeder Cubeis a dual heavy duty controller,housed in a Nema-12 oilresistant enclosure with partssensing. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 15 amps and Unit B isfused for 8 amps.








The FC-99H-4 Plus Feeder Cubeis a dual heavy duty controller,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 15 amps and Unit B isfused for 8 amps.








The FC-99H-5 Plus Feeder Cubeis a dual heavy duty controller,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Includes inputand output power cords. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 15 amps andUnit B is fused for 8 amps.








The FC-102 Plus is a triplecontroller in a general purposeenclosure. Unit A (10 amps)and Unit C (5 amps) are 40 PlusSeries controllers. Unit B (15amps) is a 90 Plus Seriescontroller with parts sensing.Input voltage is 120VAC, 50/60Hz.








The FC-103 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (15amps) and Unit C (15 amps)are 40 Plus Series controllers.Unit B (15 amps) is a 90 PlusSeries controller with partssensing. Input voltage is120VAC, 50/60 Hz.








The FC-109 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (8amps) and Unit C (8 amps) are40 Plus Series controllers. UnitB (8 amps) is a 90 Plus Seriescontroller with parts sensing.Input voltage is 240VAC, 50/60Hz.








The FC-102-4 Plus is a triplecontroller in a general purposeenclosure. Unit A (10 amps)and Unit C (5 amps) are 40 PlusSeries controllers. Unit B (15amps) is a 90 Plus Seriescontroller with a 111-500 fiberoptic sensor installed. Inputvoltage is 120VAC, 50/60 Hz.








The FC-102-5 Plus is a triplecontroller in a general purposeenclosure. Unit A (10 amps)and Unit C (5 amps) are 40 PlusSeries controllers. Unit B (15amps) is a 90 Plus Seriescontroller with a 111-500 fiberoptic sensor installed and (2)111-52 fiber optic cables. Inputvoltage is 120VAC, 50/60 Hz.








The FC-103-4 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (15amps) and Unit C (15 amps)are 40 Plus Series controllers.Unit B (15 amps) is a 90 PlusSeries controller with a111-500 fiber optic sensorinstalled. Input voltage is120VAC, 50/60 Hz.








The FC-103-5 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (15amps) and Unit C (15 amps)are 40 Plus Series controllers.Unit B (15 amps) is a 90 PlusSeries controller with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Input voltage is120VAC, 50/60 Hz.








The FC-109-4 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (8amps) and Unit C (8 amps) are40 Plus Series controllers. UnitB (8 amps) is a 90 Plus Seriescontroller with a 111-500 fiberoptic sensor installed. Inputvoltage is 240VAC, 50/60 Hz.








The FC-109-5 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (8amps) and Unit C (8 amps) are40 Plus Series controllers. UnitB (8 amps) is a 90 Plus Seriescontroller with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables. Inputvoltage is 240VAC, 50/60 Hz.








The FC-103H Plus is a tripleheavy duty controller in aNema-12 oil resistantenclosure. Unit A (5 amps) andUnit C (5 amps) are 40 PlusSeries controllers. Unit B (30amps) is a 90 Plus Seriescontroller with parts sensing.Input voltage is 120VAC, 50/60Hz.








The FC-109H Plus is a tripleheavy duty controller in aNema-12 oil resistantenclosure. Unit A (5 amps) andUnit C (5 amps) are 40 PlusSeries controllers. Unit B (30amps) is a 90 Plus Seriescontroller with parts sensing.Input voltage is 240VAC, 50/60Hz.








The FC-90-DC Plus FeederCube is a single controller withparts sensing and a DC outputdesigned for use with a motor.It is housed in a Nema-1general purpose enclosure.Input voltage is 120VAC,50/60Hz. Output voltage is0-90 VDC or 0-130 VDC. Fusedfor 10 amps. NOT UL LISTED.

FC-90 Plus SeriesFC-90-DC Plus — 121-000-8770







The FC-112 Plus Feeder Cube isa triple controller with two 90Plus Series parts sensing unitsand one 40 Plus Series unit in aNema-1 general purposeenclosure. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps, Unit B for15 amps and Unit C for 5 amps.








The FC-113 Plus Feeder Cube isa triple controller with two 90Plus Series parts sensing unitsand one 40 Plus Series unit in aNema-12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. Units A, Band C are all fused for 15amps.








The FC-119 Plus Feeder Cube isa triple controller with two 90Plus Series parts sensing unitsand one 40 Plus Series unit in aNema-12 oil resistantenclosure. Input voltage is240VAC, 50/60 Hz. Units A, Band C are all fused for 8 amps.








The FC-113H Plus Feeder Cubeis a triple heavy dutycontroller with two 90 PlusSeries parts sensing units andone 40 Plus Series unit in aNema-12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. Units A andC are fused for 5 amps; Unit Bis fused for 30 amps.








The FC-119H Plus Feeder Cubeis a triple heavy dutycontroller with two 90 PlusSeries parts sensing units andone 40 Plus Series unit in aNema-12 oil resistantenclosure. Input voltage is240VAC, 50/60 Hz. Units A andC are fused for 5 amps; Unit Bis fused for 15 amps.








The FC-91-DC Plus FeederCube is a single controller withparts sensing and a DC outputdesigned for use with a motor.It is housed in a Nema-12 oilresistant enclosure. Inputvoltage is 120VAC, 50/60Hz.Output voltage is 0-90 VDC or0-130 VDC. Fused for 10 amps.NOT UL LISTED.

FC-90 Plus SeriesFC-91-DC Plus — 121-000-8776







The FC-112-240 Plus FeederCube is a triple controller withtwo 90 Plus Series partssensing units and one 40 PlusSeries unit in a Nema-1 generalpurpose enclosure. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 5 amps, UnitB for 8 amps and Unit C for 2amps.








The FC-90-240 Plus FeederCube is a single controller withparts sensing, housed in aNema-1 general purposeenclosure. Input voltage is240VAC, 50/60 Hz. Fused for 8amps.








The FC-90-2-240 Plus FeederCube is a dual controller withtwo part sensing units, housedin a Nema-1 general purposeenclosure. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.

FC-90 Plus SeriesFC-90-2-240 Plus — 121-000-8784







The FC-90-3-240 Plus FeederCube is a triple controller withthree part sensing units,housed in a Nema-1 generalpurpose enclosure. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 5 amps; UnitB is fused for 8 amps; Unit C isfused for 2 amps.








The FC-90-4-240 Plus FeederCube is a single controller withparts sensing, housed in aNema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.








The FC-90-5-240 Plus FeederCube is a single controller withparts sensing, housed in aNema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed and (2)111-52 fiber optic cables. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.








The FC-92-240 Plus FeederCube is a dual controller,housed in a Nema-1 generalpurpose enclosure with partssensing. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.








The FC-92-4-240 Plus FeederCube is a dual controller,housed in a Nema-1 generalpurpose enclosure with a111-500 fiber optic sensorinstalled. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.








The FC-92-5-240 Plus FeederCube is a dual controller,housed in a Nema-1 generalpurpose enclosure with a111-500 fiber optic sensorinstalled and (2) 111-52 fiberoptic cables. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.








The FC-102-240 Plus is a triplecontroller in a general purposeenclosure. Unit A (5 amps) andUnit C (2 amps) are 40 PlusSeries controllers. Unit B (8amps) is a 90 Plus Seriescontroller with parts sensing.Input voltage is 240VAC, 50/60Hz.








The FC-102-4-240 Plus is atriple controller in a generalpurpose enclosure. Unit A (5amps) and Unit C (2 amps) are40 Plus Series controllers. UnitB (8 amps) is a 90 Plus Seriescontroller with a 111-500 fiberoptic sensor installed. Inputvoltage is 240VAC, 50/60 Hz.








The FC-102-5-240 Plus is atriple controller in a generalpurpose enclosure. Unit A (5amps) and Unit C (2 amps) are40 Plus Series controllers. UnitB (8 amps) is a 90 Plus Seriescontroller with a 111-500 fiberoptic sensor installed and (2)111-52 fiber optic cables. Inputvoltage is 240VAC, 50/60 Hz.








The FC-40-90-40-40 PlusFeeder Cube is a quadcontroller in a general purposeenclosure. Units A, C and D arebased on the FC-40 Plus Seriesand Unit B is an FC-90 PlusSeries controller. Input voltageis 120VAC, 50/60 Hz. Unit A isfused for 5 amps, Unit B isfused for 8 amps and Units C &D are fused for 1 amp. NOT ULLISTED.

FC-90 Plus SeriesFC-40-90-40-40 — 121-000-8821







The FC-90-90-40-40 PlusFeeder Cube is a quadcontroller in a general purposeenclosure. Units A and B areFC-90 Plus Series controls andUnits C and D are FC-40 PlusSeries controls. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 5 amps, Unit B isfused for 8 amps and Units C &D are fused for 1 amp. NOT ULLISTED.

FC-90 Plus SeriesFC-90-90-40-40 — 121-000-8822







The FC-90-90-90-40 PlusFeeder Cube is a quadcontroller in a general purposeenclosure. Units A, B and C areFC-90 Plus Series controls andUnit D is an FC-40 Plus Seriescontrol. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 5 amps, Unit B isfused for 8 amps and Units C &D are fused for 1 amp. NOT ULLISTED.

FC-90 Plus SeriesFC-90-90-90-40 — 121-000-8823














The FC-40-90-40-40-240 Plus isa quad controller in a generalpurpose enclosure. Unit A (5amps) and Units C and D (1amp each) are 40 Plus Seriescontrollers. Unit B (8 amps) isa 90 Plus Series controller withparts sensing. Input voltage is240VAC, 50/60 Hz. NOT ULLISTED.

FC-90 Plus SeriesFC-40-90-40-40-240 — 121-000-8826





121-000-8826

121-000-8826



The FC-90-90-40-40-240 PlusFeeder Cube is a quadcontroller in a general purposeenclosure. Units A and B areFC-90 Plus Series controls andUnits C and D are FC-40 PlusSeries controls. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 5 amps, Unit B isfused for 8 amps and Units C &D are fused for 1 amp. NOT ULLISTED.

FC-90 Plus SeriesFC-90-90-40-40-240 — 121-000-8827





121-000-8827

121-000-8827



The FC-90-90-90-40-240 PlusFeeder Cube is a quadcontroller in a general purposeenclosure. Units A, B and C areFC-90 Plus Series controls andUnit D is an FC-40 Plus Seriescontrol. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 5 amps, Unit B isfused for 8 amps and Units C &D are fused for 1 amp. NOT ULLISTED.

FC-90 Plus SeriesFC-90-90-90-40-240 — 121-000-8828





121-000-8828

121-000-8828








121-000-8829

121-000-8829



The FC-200 Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a Nema 1 general purposeenclosure. Input voltage is120VAC, 50/60 Hz. Output isfused for 15 amps.

FC-200 Plus SeriesFC-200 — 121-000-2000

FC-200 Series "Parts Sensing" Feeder Cube®Controllers

FC-200 Series Typical Applications Vibratory bowls that require part sensingStorage hoppers using photoelectric bowllevel detectors

Most models are UL and cUL listed (File EI83233)Provides a soft-start adjustment so a feederbowl, inline track drive or storage hopper cancycle on gently.Maximum output power level adjustment allowsfor the maximum output of the control to bepreset.Output is selectable from 120 pulses per second(UN-rectified or full-wave) to 60 pulses persecond (rectified or half-wave).Line voltage compensation featureautomatically adjusts the output of thecontroller to compensate for incoming voltagefluctuations.12vdc power supply provided along withseparate on and off time delays for the partssensor (NPN or PNP).Auxiliary output provided for interlocking withother Rodix controlsA Constant Feed Rate (CFR) sensor can be


installed to automatically adjust the output ofthe control based on the vibration level of thefeeder.For additional features refer to the AdvancedApplication Notes.


The FC-200-2 Feeder Cube is adual digital controller with twopart sensing units, housed in aNema-1 general purposeenclosure. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 5 amps.

FC-200 Plus SeriesFC-200-2 — 121-000-2001







The FC-200-3 Feeder Cube is atriple digital controller withthree part sensing units,housed in a Nema-1 generalpurpose enclosure. Inputvoltage is 120VAC, 50/60 Hz.Unit A is fused for 10 amps;Unit B is fused for 15 amps;Unit C is fused for 5 amps.

FC-200 Plus SeriesFC-200-3 — 121-000-2002







The FC-205 Feeder Cube is asingle FC-200 Series digitalcontrol designed for mountinginside a larger cabinet on thesubpanel. The sides are openfor easy access to the terminalstrips for applying power andsensors. Input voltage is120VAC and the unit is fusedfor 15 amps.

FC-200 Plus SeriesFC-205 — 121-000-2005







The FC-201 Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a Nema 12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. Output isfused for 15 amps.

FC-200 Plus SeriesFC-201 — 121-000-2006







The FC-201-2 Feeder Cube is adual digital controller housedin a Nema-12 oil resistantenclosure. Units A and B areFC-200 Series controllers. Inputvoltage is 120VAC, 50/60 Hz.Both units are rated for 15amps.

FC-200 Plus SeriesFC-201-2 — 121-000-2007







The FC-201-3 Feeder Cube is atriple digital controller housedin a Nema-12 oil resistantenclosure. Units A, B and C areFC-200 Series controllers. Inputvoltage is 120VAC, 50/60 Hz.All three units are rated for 15amps.

FC-200 Plus SeriesFC-201-3 — 121-000-2008







The FC-201H Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a Nema 12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. Output isfused for 30 amps.

FC-200 Plus SeriesFC-201H — 121-000-2009







The FC-201-2H Feeder Cube isa dual digital control based onthe 90 Plus Series. It is housedin a Nema 12 oil resistantenclosure. Input voltage is120VAC, 50/60 Hz. The outputof Unit A is fused for 30 amps;the output of Unit B is fusedfor 15 amps.

FC-200 Plus SeriesFC-201-2H — 121-000-2010







The FC-205-240 Feeder Cube isa single FC-200 Series digitalcontrol designed for mountinginside a larger cabinet on thesubpanel. The sides are openfor easy access to the terminalstrips for applying power andsensors. Input voltage is240VAC and the unit is fusedfor 8 amps.

FC-200 Plus SeriesFC-205-240 — 121-000-2013







The FC-208 Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a Nema 12 oil resistantenclosure. Input voltage is240VAC, 50/60 Hz. Output isfused for 8 amps.

FC-200 Plus SeriesFC-208 — 121-000-2014







The FC-208-2 Feeder Cube is adual digital controller housedin a Nema-12 oil resistantenclosure. Units A and B areFC-200 Series controllers. Inputvoltage is 240VAC, 50/60 Hz.Both units are rated for 8amps.

FC-200 Plus SeriesFC-208-2 — 121-000-2015







The FC-208-3 Feeder Cube is atriple digital controller housedin a Nema-12 oil resistantenclosure. Units A, B and C areFC-200 Series controllers. Inputvoltage is 240VAC, 50/60 Hz.All three units are rated for 8amps.

FC-200 Plus SeriesFC-208-3 — 121-000-2016







The FC-208H Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a Nema 12 oil resistantenclosure. Input voltage is240VAC, 50/60 Hz. Output isfused for 15 amps.

FC-200 Plus SeriesFC-208H — 121-000-2017







The FC-208-2H Feeder Cube isa dual digital control based onthe 90 Plus Series. It is housedin a Nema 12 oil resistantenclosure. Input voltage is240VAC, 50/60 Hz. The outputof Unit A is fused for 15 amps;the output of Unit B is fusedfor 8 amps.








The FC-200-4 Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a Nema 1 general purposeenclosure and comes with a111-500 Banner fiber opticsensor installed. Fiber opticcables are not included. Inputvoltage is 120VAC, 50/60 Hz.Output is fused for 15 amps.

FC-200 Plus SeriesFC-200-4 — 121-000-2019







The FC-200-5 Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a Nema 1 general purposeenclosure and comes with a111-500 Banner fiber opticsensor installed and (2)111-000-0052 36" black plasticfiber optic cables. Inputvoltage is 120VAC, 50/60 Hz.Output is fused for 15 amps.

FC-200 Plus SeriesFC-200-5 — 121-000-2020







The FC-201-4 Feeder Cube is adigital single controller withparts sensing, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed. Inputvoltage is 120VAC, 50/60 Hz.Fused for 15 amps.

FC-200 Plus SeriesFC-201-4 — 121-000-2021







The FC-201-5 Feeder Cube is asingle digital controller withparts sensing, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables. Maleand female line cords installedfor incoming and outgoingpower. Input voltage is120VAC, 50/60 Hz. Fused for15 amps.

FC-200 Plus SeriesFC-201-5 — 121-000-2022







The FC-208-4 Feeder Cube is adigital single controller withparts sensing, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.

FC-200 Plus SeriesFC-208-4 — 121-000-2034







The FC-208-5 Feeder Cube is asingle digital controller withparts sensing, housed in aNema-12 oil resistantenclosure with input andoutput power cords installed(plugs not included). A 111-500fiber optic sensor is installedand (2) 111-31 fiber opticcables are included. Inputvoltage is 240VAC, 50/60 Hz.Fused for 8 amps.

FC-200 Plus SeriesFC-208-5 — 121-000-2035







The FC-200-240 Feeder Cube isa single digital controller withparts sensing, housed in aNema-1 general purposeenclosure. Input voltage is240VAC, 50/60 Hz. Fused for 8amps.

FC-200 Plus SeriesFC-200-240 — 121-000-2060







The FC-200-4-240 Feeder Cubeis a single digital control basedon the 90 Plus Series. It ishoused in a Nema 1 generalpurpose enclosure and comeswith a 111-500 Banner fiberoptic sensor installed. Fiberoptic cables are not included.Input voltage is 240VAC, 50/60Hz. Output is fused for 8 amps.

FC-200 Plus SeriesFC-200-4-240 — 121-000-2061







The FC-200-5-240 Feeder Cubeis a single digital control basedon the 90 Plus Series. It ishoused in a Nema 1 generalpurpose enclosure and comeswith a 111-500 Banner fiberoptic sensor installed and (2)111-000-0052 36" black plasticfiber optic cables. Inputvoltage is 240VAC, 50/60 Hz.Output is fused for 8 amps.

FC-200 Plus SeriesFC-200-5-240 — 121-000-2062







The FC-200-2-240 Feeder Cubeis a dual digital controller withtwo part sensing units, housedin a Nema-1 general purposeenclosure. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.

FC-200 Plus SeriesFC-200-2-240 — 121-000-2063







The FC-200-3-240 Feeder Cubeis a triple digital controllerwith three part sensing units,housed in a Nema-1 generalpurpose enclosure. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 5 amps; UnitB is fused for 8 amps; Unit C isfused for 2 amps.

FC-200 Plus SeriesFC-200-3-240 — 121-000-2064







The FC-201-3H Feeder Cube isa triple digital control basedon the 90 Plus Series. It ishoused in a Nema 12 oilresistant enclosure. Inputvoltage is 120VAC, 50/60 Hz.The output of Units A and Care fused for 5 amps; theoutput of Unit B is fused for 30amps.








The FC-208-3H Feeder Cube isa triple digital control basedon the 90 Plus Series. It ishoused in a Nema 12 oilresistant enclosure. Inputvoltage is 240VAC, 50/60 Hz.The output of Units A and Care fused for 8 amps; theoutput of Unit B is fused for 15amps.








The FC-201 Feeder Cube is asingle digital control based onthe 90 Plus Series. It is housedin a 10 x 8 x 4 Nema 12 oilresistant enclosure. Inputvoltage is 120VAC, 50/60 Hz.Output is fused for 15 amps.

FC-200 Plus SeriesFC-201 in 10 x 8 x 4 enclosure —121-000-2080



Most models are UL and cUL listed (File EI83233)Provides a soft-start adjustment so a feederbowl, inline track drive or storage hopper cancycle on gently.Maximum output power level adjustment allowsfor the maximum output of the control to bepreset.Output is selectable from 120 pulses per second(UN-rectified or full-wave) to 60 pulses persecond (rectified or half-wave).Line voltage compensation featureautomatically adjusts the output of thecontroller to compensate for incoming voltagefluctuations.12vdc power supply provided along withseparate on and off time delays for the partssensor (NPN or PNP).Auxiliary output provided for interlocking withother Rodix controls


121-000-2080

121-000-2080

A Constant Feed Rate (CFR) sensor can beinstalled to automatically adjust the output ofthe control based on the vibration level of thefeeder.For additional features refer to the AdvancedApplication Notes.


The FC-201-2 Feeder Cube is adual digital controller housedin a 12 x 12 x 6 Nema-12 oilresistant enclosure. Units Aand B are FC-200 Seriescontrollers. Input voltage is120VAC, 50/60 Hz. Both unitsare rated for 15 amps.

FC-200 Plus SeriesFC-201-2 in 12 x 12 x 6 enclosure —121-000-2081















The FC-201-3 Feeder Cube is atriple digital controller housedin a 14 x 12 x 6 Nema-12 oilresistant enclosure with all ofthe components installed onthe left side of the panelleaving the right half emptyfor installing auxiliaryequipment. Units A, B and Care FC-200 Series controllers.Input voltage is 120VAC, 50/60Hz. All three units are ratedfor 15 amps.














121-000-2085

121-000-2085

















121-000-2087

121-000-2087



The FC-201-3 Feeder Cube is atriple digital controller housedin a 16 x 14 x 6 Nema-12 oilresistant enclosure with aspecial panel layout. All of thecomponents on the panel areinstalled on the upper lefthand corner leaving a largearea for installing auxiliaryequipment. Units A, B and Care FC-200 Series controllers.Input voltage is 120VAC, 50/60Hz. All three units are ratedfor 15 amps.








The FC-201-2 Feeder Cube is adual digital controller housedin a 16 x 14 x 6 Nema-12 oilresistant enclosure. Units Aand B are FC-200 Seriescontrollers. Input voltage is120VAC, 50/60 Hz. Both unitsare rated for 15 amps.








The FC-208-3 Feeder Cube is atriple digital controller housedin a 16 x 14 x 6 Nema-12 oilresistant enclosure. Units A, Band C are FC-200 Seriescontrollers. Input voltage is240VAC, 50/60 Hz. All threeunits are rated for 8 amps.
























The FC-201-3 Feeder Cube is atriple digital controller housedin a 16 x 14 x 10 Nema-12 oilresistant enclosure with aspecial panel layout. All of thecomponents on the panel areinstalled on the upper lefthand corner leaving a largearea for installing auxiliaryequipment. Units A, B and Care FC-200 Series controllers.Input voltage is 120VAC, 50/60Hz. All three units are ratedfor 15 amps.








The FC-201-Q Feeder Cube is aquad digital controller housedin a Nema-12 oil resistantenclosure consisting of fourFC-200 Series controllers. Inputvoltage is 120VAC, 50/60 Hz.All four units are rated for 15amps. NOT UL LISTED.








The FC-200-Q Feeder Cube is aquad digital controller withfour part sensing units, housedin a Nema-1 general purposeenclosure. Input voltage is120VAC, 50/60 Hz. Units A andC are fused for 2 amps; Units Band D are fused for 5 amps.NOT UL LISTED.








The FC-200-Q-240 Feeder Cubeis a quad digital controllerwith four part sensing units,housed in a Nema-1 generalpurpose enclosure. Inputvoltage is 240VAC, 50/60 Hz.Units A and C are fused for 2amps; Units B and D are fusedfor 5 amps. NOT UL LISTED.






121-000-2111

121-000-2111



The VFC-9-200-2 Feeder Cubeis a triple control for operatinga vibratory bowl with a storagehopper and an inline. Unit A isa VF-9 variable frequencycontroller and units B & C areFC-200 fixed frequency digitalcontrollers. Input voltage is120VAC, 50/60 Hz. Output forUnit A is fused for 9 amps,Units B and C are fused for 5amps each. Vibration sensorsare sold separately.

VFC SeriesVFC-9-200-2 — 121-200-0757

VFC Series Feeder Cube® Controllers

Easy to read backlit control displays and easy tounderstand status messages.Simple to navigate set-up menu will have youup and running quickly.Resonant frequency of the Variable Frequencycontrol(s) can be found manually using thekeypad or automatically by mounting thevibration sensor and letting the controller scanthe frequency range (5-300 Hz)A Constant Feed Rate (CFR) sensor can beinstalled in the FC-200 Series fixed frequencycontrollers to automatically adjust the output ofthe control based on the vibration level of thebowl..The controls can be interlocked with each otherso that when the bowl turns off, the hopper isdisabled and the inline (if applicable) runscontinuously or also turns off.Control display messages can be shown inEnglish, Spanish, French or GermanKeypad can be locked with a security codepreventing operators from changing settingsLine voltage compensation featureautomatically adjusts the output of thecontroller to compensate for incoming voltage


fluctuationsPlease refer to the Application Note foradditional features and adjustments.Made in the U.S.A


The VFC-9-200 Feeder Cube isa dual controller for operatinga vibratory bowl and storagehopper or a vibratory bowl anda linear inline. Unit A is a VF-9Variable Frequency controller;Unit B is an FC-200 FeederCube. Input voltage is 120VAC,50/60 Hz. Output for Unit A isfused for 9 amps, Unit B isfused for 8 amps. Vibrationsensors are sold separately.

VFC SeriesVFC-9-200 — 121-200-0758






The VFC-9-2-200 is a triplecontroller in a general purposeenclosure with two variablefrequency VF-9 controls andone FC-200 Series control. ULlisted (File E183233). Inputvoltage is 120VAC, 50/60 Hz.Output voltage is 0-120 VAC.The rated output current forUnits A and B is 9 amps and theoutput frequency is 5-300 Hz.The rated output current forUnit C is 5 amps and theoutput frequency is 50/60 Hz.

VFC SeriesVFC-9-2-200 — 121-200-0767






The VFC-3-200 Feeder Cube isa dual controller for operatinga vibratory bowl and storagehopper or a vibratory bowl anda linear inline. Unit A is a VF-3Variable Frequency controller;Unit B is an FC-200 FeederCube. Input voltage is 120VAC,50/60 Hz. Output for Unit A isfused for 3 amps, Unit B isfused for 8 amps. Vibrationsensors are sold separately.

VFC SeriesVFC-3-200 — 121-200-0779






The VFC-3-200-240 FeederCube is a dual controller foroperating a vibratory bowl andstorage hopper or a vibratorybowl and a linear inline. Unit Ais a VF-3 Variable Frequencycontroller; Unit B is anFC-200-240 Feeder Cube. Inputvoltage is 240VAC, 50/60 Hz.Output for Unit A is fused for 3amps, Unit B is fused for 8amps. Vibration sensors aresold separately.

VFC SeriesVFC-3-200-240 — 121-200-0783






The VF-9 AUTO TUNE® FeederCube is a single variablefrequency controller in aNema-1 general purposeenclosure with the vibrationsensor installed. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 9 ampsat 120VAC or 4.5 amps at240VAC.

Auto Tune® (VFSeries)VF-9 with vibration sensor —121-000-0751

Universal 85-264 VAC input voltage operatingrangeEasy to read backlit control display and easy tounderstand status message.Simple to navigate set-up menu will have youup and running quickly.Resonant frequency can be found manuallyusing the keypad or automatically by mountingthe vibration sensor and letting the controllerscan the frequency range (5-140 HZ or 5-300Hzdepending on software version)An NPN or PNP parts sensor can be added (fiberoptic or proximity) to cycle the feeder on andoff.Optional operating modes include an emptybowl/parts jam indicator, two speed operationand an "always on" feature that when used inconjunction with the auxiliary output canoperate an air-jet or light standControl display messages can be shown inEnglish, Spanish, French or GermanKeypad can be locked with a security codepreventing operators from changing settingsBuilt in line voltage compensation feature willsmooth out any incoming voltage fluctuationsMade in the U.S.A


Made in the U.S.A


The VF-9-OR AUTO TUNE®Feeder Cube is a singlevariable frequency controllerthat comes with the vibrationsensor installed. The enclosureis rated for an IP54environment and UL rated for aType 5 environment. UL listed(File E183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 9 ampsat 120 VAC or 4.5 amps at240VAC.

Auto Tune® (VFSeries)VF-9-OR with vibration sensor —121-000-0752

Universal 85-264 VAC input voltage operatingrangeEasy to read backlit control display and easy tounderstand status message.Simple to navigate set-up menu will have youup and running quickly.Resonant frequency can be found manuallyusing the keypad or automatically by mountingthe vibration sensor and letting the controllerscan the frequency range (5-140 HZ or 5-300Hzdepending on software version)An NPN or PNP parts sensor can be added (fiberoptic or proximity) to cycle the feeder on andoff.Optional operating modes include an emptybowl/parts jam indicator, two speed operationand an "always on" feature that when used inconjunction with the auxiliary output canoperate an air-jet or light standControl display messages can be shown inEnglish, Spanish, French or GermanKeypad can be locked with a security codepreventing operators from changing settingsBuilt in line voltage compensation feature willsmooth out any incoming voltage fluctuations


Made in the U.S.A


The VF-3 AUTO TUNE® FeederCube is a single variablefrequency controller in aNema-1 general purposeenclosure with the vibrationsensor installed. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 3 ampsat 120VAC or 1.5 amps at240VAC.




Made in the U.S.A


The VF-12 AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a Nema-1 general purposeenclosure with the vibrationsensor installed. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 10 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-140 Hz.Rated output current is 12amps at 120VAC or 6 amps at240VAC.




Made in the U.S.A


The VF-18 AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a Nema-1 general purposeenclosure with the vibrationsensor installed. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 10 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-140 Hz.Rated output current is 18amps at 120VAC or 9 amps at240VAC.




Made in the U.S.A


The VF-12-OR AUTO TUNE®Feeder Cube is a singlevariable frequency controllerthat comes with the vibrationsensor installed. The enclosureis rated for an IP54environment and UL rated for aType 5 environment. UL listed(File E183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 10 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-140 Hz.Rated output current is 12amps at 120 VAC or 6 amps at240VAC.




Made in the U.S.A


The VF-3-OR AUTO TUNE®Feeder Cube is a singlevariable frequency controllerthat comes with the vibrationsensor installed. The enclosureis rated for an IP54environment. Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 3 ampsat 120 VAC or 1.5 amps at240VAC. NOT UL LISTED.




Made in the U.S.A


The VF-3-OF AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a open frame panel mountstyle enclosure with thevibration sensor installed.Input voltage is 85-264 VAC,50/60 Hz and fused for 5 amps.Output voltage is 0-120/240VAC. Output frequency is 5-140Hz. Rated output current is 3amps at 120VAC or 1.5 amps at240VAC. NOT UL LISTED.

Auto Tune® (VFSeries)VF-3-OF with vibration sensor —121-000-0777



Made in the U.S.A


The VF-9-OF AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a open frame panel mountstyle enclosure with thevibration sensor installed.Input voltage is 85-264 VAC,50/60 Hz and fused for 5 amps.Output voltage is 0-120/240VAC. Output frequency is 5-300Hz. Rated output current is 9amps at 120VAC or 4.5 amps at240VAC. NOT UL LISTED.

Auto Tune® (VFSeries)VF-9-OF with vibration sensor —121-000-0778



Made in the U.S.A


The VF-9CE AUTO TUNE®Feeder Cube is a single CEmarked variable frequencycontroller in an IP-54 /Nema-12 oil resistantenclosure. Vibration sensorincluded. Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 9 ampsat 120 VAC or 4.5 amps at240VAC. NOT UL LISTED.

Auto Tune® (VFSeries)VF-9CE with vibration sensor —121-000-0780



Made in the U.S.A


The VF-3CE AUTO TUNE®Feeder Cube is a single CEmarked variable frequencycontroller in an IP-54 /Nema-12 oil resistantenclosure. Vibration sensorincluded. Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 3 ampsat 120 VAC or 1.5 amps at240VAC. NOT UL LISTED.

Auto Tune® (VFSeries)VF-3CE with vibration sensor —121-000-0781



Made in the U.S.A


The VF-9 AUTO TUNE® FeederCube is a single variablefrequency controller in aNema-1 general purposeenclosure. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 9 ampsat 120VAC or 4.5 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215.

Auto Tune® (VFSeries)VF-9 without vibration sensor —121-200-0751



Made in the U.S.A


The VF-9-OR AUTO TUNE®Feeder Cube is a singlevariable frequency controllerbuilt in an enclosure rated foran IP54 environment and ULrated for a Type 5environment. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 9 ampsat 120 VAC or 4.5 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215.

Auto Tune® (VFSeries)VF-9-OR without vibration sensor —121-200-0752



Made in the U.S.A


The VF-3 AUTO TUNE® FeederCube is a single variablefrequency controller in aNema-1 general purposeenclosure. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 3 ampsat 120VAC or 1.5 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215.




Made in the U.S.A


The VF-12 AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a Nema-1 general purposeenclosure. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 10 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-140 Hz.Rated output current is 12amps at 120VAC or 6 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215.




Made in the U.S.A


The VF-18 AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a Nema-1 general purposeenclosure. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 10 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-140 Hz.Rated output current is 18amps at 120VAC or 9 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215.




Made in the U.S.A


The VF-9-3 AUTO TUNE®Feeder Cube is a triplecontroller with three variablefrequency units in a Nema-1general purpose enclosure. ULlisted (File E183233). Inputvoltage for units A, B and C is85-264 VAC, 50/60 Hz andfused for 5 amps each. Theoutput voltage for each unit is0-120/240 VAC. The outputfrequency for each unit is5-300 Hz. The rated outputcurrent of each unit is 9 ampsat 120VAC or 4.5 amps at240VAC. Vibration sensor kit123-000-0215 sold separately.

Auto Tune® (VFSeries)VF-9-3 — 121-200-0759




The VF-9-2 AUTO TUNE®Feeder Cube is a dualcontroller with two variablefrequency units in a Nema-1general purpose enclosure. ULlisted (File E183233). Inputvoltage for both units A and Bis 85-264 VAC, 50/60 Hz andfused for 5 amps each. Theoutput voltage for each unit is0-120/240 VAC. The outputfrequency for each unit is5-300 Hz. The rated outputcurrent for each unit is 9 ampsat 120VAC or 4.5 amps at240VAC. Vibration sensor kit123-000-0215 sold separately.





The VF-3-3 AUTO TUNE®Feeder Cube is a triplecontroller with three variablefrequency units in a Nema-1general purpose enclosure. ULlisted (File E183233). Inputvoltage for units A, B and C is85-264 VAC, 50/60 Hz andfused for 5 amps each. Theoutput voltage for each unit is0-120/240 VAC. The outputfrequency for each unit is5-300 Hz. The rated outputcurrent for each unit is 3 ampsat 120VAC or 1.5 amps at240VAC. Vibration sensor kit123-000-0215 sold separately.





The VF-3-2 AUTO TUNE®Feeder Cube is a dualcontroller with two variablefrequency units in a Nema-1general purpose enclosure. ULlisted (File E183233). Inputvoltage for both units A and Bis 85-264 VAC, 50/60 Hz andfused for 5 amps each. Theoutput voltage for each unit is0-120/240 VAC. The outputfrequency for each unit is5-300 Hz. The rated outputcurrent of each unit is 3 ampsat 120VAC or 1.5 amps at240VAC. Vibration sensor kit123-000-0215 sold separately.





The VF-39 AUTO TUNE®Feeder Cube is a dualcontroller with two variablefrequency units in a Nema-1general purpose enclosure. ULlisted (File E183233). Inputvoltage for both units A and Bis 85-264 VAC, 50/60 Hz andfused for 5 amps each. Theoutput voltage for each unit is0-120/240 VAC. The outputfrequency for each unit is5-300 Hz. The rated outputcurrent for Unit A is 3 amps at120VAC or 1.5 amps at 240VAC.The rated output current forUnit B is 9 amps at 120VAC or4.5 amps at 240VAC. Vibrationsensor kit 123-000-0215 soldseparately.

Auto Tune® (VFSeries)VF-39 — 121-200-0764




The VF-393 AUTO TUNE® is atriple variable frequencycontroller in a Nema-1 generalpurpose enclosure with (2)VF-3 controls for an inline anda hopper and (1) VF-9 controlfor the bowl. UL listed (FileE183233). Input voltage forUnits A, B and C is 85-264 VAC,50/60 Hz and fused for 5 ampseach. Output voltage is0-120/240 VAC. Outputfrequency for each unit is5-300 Hz. The rated outputcurrent for Units A and C is 3amps at 120VAC or 1.5 amps at240VAC. The rated outputcurrent for Unit B is 9 amps at120VAC or 4.5 amps at 240VAC.Vibration sensor kit123-000-0215 sold separately.

Auto Tune® (VFSeries)VF-393 — 121-200-0769



123-000-0215 sold separately.


The VF-12-OR AUTO TUNE®Feeder Cube is a singlevariable frequency controllerbuilt in an enclosure rated foran IP54 environment and ULrated for a Type 5environment. UL listed (FileE183233). Input voltage is85-264 VAC, 50/60 Hz andfused for 10 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-140 Hz.Rated output current is 12amps at 120 VAC or 6 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215.




Made in the U.S.A


The VF-3-OR AUTO TUNE®Feeder Cube is a singlevariable frequency controllerbuilt in an enclosure rated foran IP54 environment. Inputvoltage is 85-264 VAC, 50/60Hz and fused for 5 amps.Output voltage is 0-120/240VAC. Output frequency is 5-300Hz. Rated output current is 3amps at 120 VAC or 1.5 ampsat 240VAC. Vibration sensorsold separately, see partnumber 123-000-0215. Unit isnot UL listed.




Made in the U.S.A


The VF-3-OF AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a open frame panel mountstyle enclosure. Input voltageis 85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-140 Hz.Rated output current is 3 ampsat 120VAC or 1.5 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215. Unit is not ULlisted.

Auto Tune® (VFSeries)VF-3-OF without vibration sensor —121-200-0777



Made in the U.S.A


The VF-9-OF AUTO TUNE®Feeder Cube is a singlevariable frequency controllerin a open frame panel mountstyle enclosure. Input voltageis 85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 9 ampsat 120VAC or 4.5 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215. Unit is not ULlisted.

Auto Tune® (VFSeries)VF-9-OF without vibration sensor —121-200-0778



Made in the U.S.A


The VF-9CE AUTO TUNE®Feeder Cube is a single CEmarked variable frequencycontroller in an IP-54 /Nema-12 oil resistantenclosure. Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 9 ampsat 120 VAC or 4.5 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215. Unit is not ULlisted.

Auto Tune® (VFSeries)VF-9CE without vibration sensor —121-200-0780



Made in the U.S.A


The VF-3CE AUTO TUNE®Feeder Cube is a single CEmarked variable frequencycontroller in an IP-54 /Nema-12 oil resistantenclosure. Input voltage is85-264 VAC, 50/60 Hz andfused for 5 amps. Outputvoltage is 0-120/240 VAC.Output frequency is 5-300 Hz.Rated output current is 3 ampsat 120 VAC or 1.5 amps at240VAC. Vibration sensor soldseparately, see part number123-000-0215. Unit is not ULlisted.

Auto Tune® (VFSeries)VF-3CE without vibration sensor —121-200-0781



Made in the U.S.A


The VFC-9-201-2 Feeder Cubeis a triple controller with (1)VF-9 variable frequencycontroller and (2) FC-200Series digital fixed frequencycontrollers housed in an oilresistant enclosure. Inputvoltage is 120VAC.

Auto Tune® (VFSeries)VFC-9-201-2 — 121-200-0785




The CE-44 Plus Feeder Cube isa single, open frame FC-40 PlusSeries controller designed forinstalling on a panel in anenclosure. The main controlpotentiometer and the switchare remotely mounted. Theunit carries the CE mark and aDeclaration of Incorporation isprovided. Input voltage is120VAC, 50/60 Hz. It is fusedfor 15 amps.

CE-40 Plus SeriesCE-44 Plus — 121-500-0704

CE-40 Plus Series "All Purpose" Feeder Cube®Controllers

CE-40 Plus Series Typical Applications Vibratory bowlsStorage hoppersLinear inline feeders

Enclosure Styles Nema-12 oil resistant (single, double andtriple units)

Provides a soft-start adjustment so a feederbowl, inline track drive or storage hopper cancycle on gently.Maximum output power level adjustment allowsfor the maximum output of the control to bepresetOutput is switch selectable from 120 pulses persecond (UN-rectified or full-wave) to 60 pulsesper second (rectified or half-wave)Line voltage compensation featureautomatically adjusts the output of thecontroller to compensate for incoming voltagefluctuations.Easily integrates with PLC's for remote controlaccess.Line filter installed to minimize the effects ofelectrical noise.


Declaration of Incorporation provided.


The CE-44-240 Plus FeederCube is a single, open frameFC-40 Plus Series controllerdesigned for installing on apanel in an enclosure. Themain control potentiometerand the switch are remotelymounted. The unit carries theCE mark and a Declaration ofIncorporation is provided.Input voltage is 240VAC, 50/60Hz. It is fused for 8 amps.

CE-40 Plus SeriesCE-44-240 Plus — 121-500-0705








The CE-41 Plus Feeder Cube isa single controller that carriesthe CE mark. It is housed in aNema-12 oil resistantenclosure. Declaration ofIncorporation provided. Inputvoltage is 120VAC, 50/60 Hz. Itis fused for 15 amps.









The CE-43 Plus Feeder Cube isa dual controller, housed in aNema-12 oil resistantenclosure that carries the CEmark. Input voltage is 120VAC,50/60 Hz. Unit A is fused for 15amps and Unit B is fused for 5amps. Declaration ofIncorporation provided.









The CE-48 Plus Feeder Cube isa single controller that carriesthe CE mark. It is housed in aNema-12 oil resistantenclosure. Declaration ofIncorporation provided. Inputvoltage is 240VAC, 50/60 Hz. Itis fused for 8 amps.









The CE-49 Plus Feeder Cube isa dual controller housed in aNema-12 oil resistantenclosure that carries the CEmark. Input voltage is 240VAC,50/60Hz. Unit A and Unit B areboth fused for 8 amps.Declaration of Incorporation isincluded.









The CE-101 Plus Feeder Cube isa triple controller housed in aNema-12 oil resistantenclosure that carries the CEmark. Input voltage is 120VAC,50/60 Hz. Units A is fused for 4amps, Unit B is fused for 15amps and Unit C is fused for 1amp. Declaration ofIncorporation included.









The CE-108 Plus Feeder Cube isa triple controller housed in aNema-12 oil resistantenclosure that carries the CEmark. Input voltage is 240VAC,50/60 Hz. Units A and B arefused for 8 amps and Unit C isfused for 1 amp. Declaration ofIncorporation provided.









The CE-45 Plus Feeder Cube isa single, open frame FC-40 PlusSeries controller designed forinstalling on a panel in anenclosure. The unit carries theCE mark and a Declaration ofIncorporation is provided.Input voltage is 120VAC, 50/60Hz. It is fused for 15 amps.









The CE-47 Plus Feeder Cube isa single, open frame FC-40 PlusSeries controller designed forinstalling on the door of anenclosure. The unit carries theCE mark and a Declaration ofIncorporation is provided.Input voltage is 120VAC, 50/60Hz. It is fused for 15 amps.









The CFR-90 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature in a Nema-1general purpose enclosure.Vibration sensor included.Input voltage is 120VAC, 50/60Hz. Fused for 15 amps.

CFR-90 Plus SeriesCFR-90 Plus — 121-100-8200

CFR-90 Plus Series "Constant Feed Rate" FeederCube® Controllers

CFR-90 Plus Series Typical Applications Vibratory bowls, storage hoppers and linearinline feeders that are susceptible to speedflucuations based on the changing vibrationlevels.

Standard Features Most models are UL and cUL listed (FileEI83233).Provides a soft-start adjustment so afeeder bowl, inline track drive or storagehopper can cycle on gently.Maximum output power level adjustmentallows for the maximum output of thecontrol to be presetOutput is switch selectable from 120 pulsesper second (UN-rectified or full-wave) to 60pulses per second (rectified or half-wave)Line voltage compensation featureautomatically adjusts the output of thecontroller to compensate for incomingvoltage fluctuations.12vdc power supply provided along withseparate on and off time delays for theparts sensor (NPN or PNP).


Auxiliary output provided for interlockingwith other Rodix controlsA Constant Feed Rate (CFR) sensor isinstalled to automatically adjust the outputof the control based on the vibration levelof the feeder.


The CFR-90-2 Plus Feeder Cubeis a dual controller with twoparts sensing units and theConstant Feed Rate feature ina Nema-1 general purposeenclosure. One vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Unit Afused for 10 amps; Unit B fusedfor 5 amps.

CFR-90 Plus SeriesCFR-90-2 Plus — 121-100-8210







The CFR-90-3 Plus Feeder Cubeis a triple controller with threeparts sensing units and theConstant Feed Rate feature ina Nema-1 general purposeenclosure. One vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Unit Afused for 10 amps; Unit B fusedfor 15 amps; Unit C fused for 5amps.








The CFR-97 Plus Feeder Cubeis a single open framecontroller with parts sensingand the Constant Feed Ratefeature for mounting on theinside of an electricalenclosure door. Input voltageis 120VAC, 50/60 Hz. Fused for15 amps. Potentiometer,switch and vibration sensorincluded.








The CFR-94 Plus Feeder Cubeis a single open framecontroller with parts sensingand the Constant Feed Ratefeature for mounting on anelectrical panel. Vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Fused for15 amps. (Potentiometer andswitch not included).








The CFR-95 Plus Feeder Cubeis a single open framecontroller with parts sensingand the Constant Feed Ratefeature for mounting on anelectrical panel. Input voltageis 120VAC, 50/60 Hz. Fused for15 amps. Potentiometer,switch and vibration sensorincluded.








The CFR-91 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature in a Nema-12 oilresistant enclosure. Vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Fused for15 amps.








The CFR-91-2 Plus Feeder Cubeis a dual controller with twoparts sensing units and theConstant Feed Rate feature ina Nema-12 oil resistantenclosure. One vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Both UnitA and Unit B are fused for 15amps.








The CFR-91-3 Plus Feeder Cubeis a triple controller with threeparts sensing units and theConstant Feed Rate feature ina Nema-12 oil resistantenclosure. One vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Unit A,Unit B and Unit C are all fusedfor 15 amps.








The CFR-91H Plus Feeder Cubeis a single heavy dutycontroller with parts sensingand the Constant Feed Ratefeature in a Nema-12 oilresistant enclosure. Vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Fused for30 amps.

CFR-90 Plus SeriesCFR-91H Plus — 121-100-8290







The CFR-91-2H Plus FeederCube is a dual heavy dutycontroller with two partssensing units and the ConstantFeed Rate feature in aNema-12 oil resistantenclosure. One vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Unit A isfused for 30 amps; Unit B isfused for 15 amps.

CFR-90 Plus SeriesCFR-91-2H Plus — 121-100-8300







The CFR-97-240 Plus FeederCube is a single open framecontroller with parts sensingand the Constant Feed Ratefeature for mounting on theinside of an electricalenclosure door. Input voltageis 240VAC, 50/60 Hz. Fused for8 amps. Potentiometer, switchand vibration sensor included.








The CFR-94-240 Plus FeederCube is a single open framecontroller with parts sensingand the Constant Feed Ratefeature for mounting on anelectrical panel. Vibrationsensor included. Input voltageis 240VAC, 50/60 Hz. Fused for8 amps. (Potentiometer andswitch not included).








The CFR-95-240 Plus FeederCube is a single open framecontroller with parts sensingand the Constant Feed Ratefeature for mounting on anelectrical panel. Input voltageis 240VAC, 50/60 Hz. Fused for8 amps. Potentiometer, switchand vibration sensor included.








The CFR-98 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature in a Nema-12 oilresistant enclosure. Vibrationsensor included. Input voltageis 240VAC, 50/60 Hz. Fused for8 amps.








The CFR-98-2 Plus Feeder Cubeis a dual controller with twoparts sensing units and theConstant Feed Rate feature ina Nema-12 oil resistantenclosure. One vibrationsensor included. Input voltageis 240VAC, 50/60 Hz. Both UnitA and Unit B are fused for 8amps.








The CFR-98-3 Plus Feeder Cubeis a triple controller with threeparts sensing units and theConstant Feed Rate feature ina Nema-12 oil resistantenclosure. One vibrationsensor included. Input voltageis 240VAC, 50/60 Hz. Unit A,Unit B and Unit C are all fusedfor 8 amps.








The CFR-98H Plus Feeder Cubeis a single heavy dutycontroller with parts sensingand the Constant Feed Ratefeature in a Nema-12 oilresistant enclosure. Vibrationsensor included. Input voltageis 240VAC, 50/60 Hz. Fused for15 amps.








The CFR-98-2H Plus FeederCube is a dual heavy dutycontroller with two partssensing units and the ConstantFeed Rate feature in aNema-12 oil resistantenclosure. One vibrationsensor included. Input voltageis 240VAC, 50/60 Hz. Unit A isfused for 15 amps; Unit B isfused for 8 amps.

CFR-90 Plus SeriesCFR-98-2H Plus — 121-100-8380







The CFR-90-4 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature, housed in aNema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed.Vibration sensor included.Input voltage is 120VAC, 50/60Hz. Fused for 15 amps.








The CFR-90-5 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature, housed in aNema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed and (2)111-52 fiber optic cables.Vibration sensor included.Input voltage is 120VAC, 50/60Hz. Fused for 15 amps.








The CFR-91-4 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed.Vibration sensor included.Input voltage is 120VAC, 50/60Hz. Fused for 15 amps.








The CFR-91-5 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables.Vibration sensor included.Input voltage is 120VAC, 50/60Hz. Fused for 15 amps.








The CFR-91H-4 Plus FeederCube is a single heavy-dutycontroller with parts sensingand the Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Fused for30 amps.

CFR-90 Plus SeriesCFR-91H-4 Plus — 121-100-8430





121-100-8430

121-100-8430



The CFR-91H-5 Plus FeederCube is a single heavy-dutycontroller with parts sensingand the Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with111-500 optic sensor installedand (2) 111-31 fiber opticcables. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Fused for30 amps.






121-100-8440

121-100-8440



The CFR-92 Plus Feeder Cubeis a dual controller with theConstant Feed Rate feature,housed in a Nema-1 generalpurpose enclosure with partssensing. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 5 amps.








The CFR-92-4 Plus Feeder Cubeis a dual controller with theConstant Feed Rate feature,housed in a Nema-1 generalpurpose enclosure with a111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 5 amps.








The CFR-92-5 Plus Feeder Cubeis a dual controller with theConstant Feed Rate feature,housed in a Nema-1 generalpurpose enclosure with a111-500 fiber optic sensorinstalled and (2) 111-52 fiberoptic cables. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 5 amps.








The CFR-93 Plus Feeder Cubeis a dual controller with partssensing and the Constant FeedRate feature, housed in aNema-12 oil resistantenclosure. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 15amps.








The CFR-93-4 Plus Feeder Cubeis a dual controller with theConstant Feed Rate feature,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 15amps.








The CFR-93-5 Plus Feeder Cubeis a dual controller with theConstant Feed Rate feature,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 15amps.








The CFR-93H Plus Feeder Cubeis a dual heavy duty controllerwith parts sensing and theConstant Feed Rate feature,housed in a Nema-12 oilresistant enclosure. Vibrationsensor included. Input voltageis 120VAC, 50/60 Hz. Unit A isfused for 30 amps and Unit B isfused for 15 amps.






121-100-8510

121-100-8510



The CFR-93H-4 Plus FeederCube is a dual heavy dutycontroller with the ConstantFeed Rate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed.Vibration sensor included.Input voltage is 120VAC, 50/60Hz. Unit A is fused for 30 ampsand Unit B is fused for 15amps.






121-100-8520

121-100-8520



The CFR-93H-5 Plus FeederCube is a dual heavy dutycontroller with the ConstantFeed Rate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables. Inputvoltage is 120VAC, 50/60 Hz.Unit A is fused for 30 amps andUnit B is fused for 15 amps.






121-100-8530

121-100-8530



The CFR-98-4 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed.Vibration sensor included.Input voltage is 240VAC, 50/60Hz. Fused for 8 amps.








The CFR-98-5 Plus Feeder Cubeis a single controller with partssensing and the Constant FeedRate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables.Vibration sensor included.Input voltage is 240VAC, 50/60Hz. Fused for 8 amps.








The CFR-98H-4 Plus FeederCube is a single heavy-dutycontroller with parts sensingand the Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Fused for15 amps.






121-100-8560

121-100-8560



The CFR-98H-5 Plus FeederCube is a single heavy-dutycontroller with parts sensingand the Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with111-500 optic sensor installedand (2) 111-31 fiber opticcables. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Fused for15 amps.






121-100-8570

121-100-8570



The CFR-99 Plus Feeder Cubeis a dual controller with partssensing and the Constant FeedRate feature, housed in aNema-12 oil resistantenclosure. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 8amps.








The CFR-99-4 Plus Feeder Cubeis a dual controller with theConstant Feed Rate feature,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 8amps.








The CFR-99-5 Plus Feeder Cubeis a dual controller with theConstant Feed Rate feature,housed in a Nema-12 oilresistant enclosure with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Both Unit Aand Unit B are fused for 8amps.








The CFR-99H Plus Feeder Cubeis a dual heavy duty controllerwith parts sensing and theConstant Feed Rate feature,housed in a Nema-12 oilresistant enclosure. Vibrationsensor included. Input voltageis 240VAC, 50/60 Hz. Unit A isfused for 15 amps and Unit B isfused for 8 amps.






121-100-8610

121-100-8610



The CFR-99H-4 Plus FeederCube is a dual heavy dutycontroller with the ConstantFeed Rate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed.Vibration sensor included.Input voltage is 240VAC, 50/60Hz. Unit A is fused for 15 ampsand Unit B is fused for 8 amps.






121-100-8620

121-100-8620



The CFR-99H-5 Plus FeederCube is a dual heavy dutycontroller with the ConstantFeed Rate feature, housed in aNema-12 oil resistantenclosure with a 111-500 fiberoptic sensor installed and (2)111-31 fiber optic cables. Inputvoltage is 240VAC, 50/60 Hz.Unit A is fused for 15 amps andUnit B is fused for 8 amps.






121-100-8630

121-100-8630



The CFR-102 Plus Feeder Cubeis a triple controller with theConstant Feed Rate feature,housed in a Nema-1 generalpurpose enclosure with partssensing. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 15 amps; Unit C isfused for 5 amps.








The CFR-103 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (15amps) and Unit C (15 amps)are 40 Plus Series controllers.Unit B (15 amps) is a 90 PlusSeries controller with partssensing and the Constant FeedRate feature. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz.






121-100-8650

121-100-8650



The CFR-109 Plus is a triplecontroller in a Nema-12 oilresistant enclosure. Unit A (8amps) and Unit C (8 amps) are40 Plus Series controllers. UnitB (8 amps) is a 90 Plus Seriescontroller with parts sensingand the Constant Feed Ratefeature. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz.






121-100-8660

121-100-8660



The CFR-102-4 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 15 amps; Unit C isfused for 5 amps.








The CFR-102-5 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled and (2) 111-52 fiberoptic cables. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A isfused for 10 amps; Unit B isfused for 15 amps; Unit C isfused for 5 amps.








The CFR-103-4 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A, UnitB and Unit C are all fused for15 amps.






121-100-8690

121-100-8690



The CFR-103-5 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz. Unit A, UnitB and Unit C are all fused for15 amps.






121-100-8700

121-100-8700



The CFR-109-4 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A, UnitB and Unit C are all fused for 8amps.






121-100-8710

121-100-8710



The CFR-109-5 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-12oil resistant enclosure with a111-500 fiber optic sensorinstalled and (2) 111-31 fiberoptic cables. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A, UnitB and Unit C are all fused for 8amps.






121-100-8720

121-100-8720



The CFR-103H Plus is a tripleheavy duty controller in aNema-12 oil resistantenclosure. Unit A (5 amps) andUnit C (5 amps) are 40 PlusSeries controllers. Unit B (30amps) is a 90 Plus Seriescontroller with parts sensingand the Constant Feed Ratefeature. Vibration sensorincluded. Input voltage is120VAC, 50/60 Hz.






121-100-8730

121-100-8730



The CFR-109H Plus is a tripleheavy duty controller in aNema-12 oil resistantenclosure. Unit A (5 amps) andUnit C (5 amps) are 40 PlusSeries controllers. Unit B (15amps) is a 90 Plus Seriescontroller with parts sensingand the Constant Feed Ratefeature. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz.






121-100-8740

121-100-8740



The CFR-113H Plus is a tripleheavy duty controller in aNema-12 oil resistantenclosure. Unit A (15 amps)and Unit B (30 amps) are 90Plus Series controllers withparts sensing and the ConstantFeed Rate feature. Unit C (15amps) is a 40 Plus Seriescontroller. Vibration sensorincluded and installed in UnitB. Input voltage is 120VAC,50/60 Hz.






121-100-8774

121-100-8774



The CFR-90-240 Plus FeederCube is a single controller withparts sensing and the ConstantFeed Rate feature in a Nema-1general purpose enclosure.Vibration sensor included.Input voltage is 240VAC, 50/60Hz. Fused for 8 amps.








The CFR-90-4-240 Plus FeederCube is a single controller withparts sensing and the ConstantFeed Rate feature, housed in aNema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed.Vibration sensor included.Input voltage is 240VAC, 50/60Hz. Fused for 8 amps.

CFR-90 Plus SeriesCFR-90-4-240 Plus — 121-100-8795







The CFR-90-5-240 Plus FeederCube is a single controller withparts sensing and the ConstantFeed Rate feature, housed in aNema-1 general purposeenclosure with a 111-500 fiberoptic sensor installed and (2)111-52 fiber optic cables.Vibration sensor included.Input voltage is 240VAC, 50/60Hz. Fused for 8 amps.








The CFR-92-240 Plus FeederCube is a dual controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure withparts sensing. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.








The CFR-92-4-240 Plus FeederCube is a dual controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.








The CFR-92-5-240 Plus FeederCube is a dual controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled and (2) 111-52 fiberoptic cables. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 8 amps; Unit B isfused for 5 amps.








The CFR-102-240 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure withparts sensing. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 5 amps; Unit B isfused for 8 amps; Unit C isfused for 2 amps.








The CFR-102-4-240 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 5 amps; Unit B isfused for 8 amps; Unit C isfused for 2 amps.








The CFR-102-5-240 Plus FeederCube is a triple controller withthe Constant Feed Ratefeature, housed in a Nema-1general purpose enclosure witha 111-500 fiber optic sensorinstalled and (2) 111-52 fiberoptic cables. Vibration sensorincluded. Input voltage is240VAC, 50/60 Hz. Unit A isfused for 5 amps; Unit B isfused for 8 amps; Unit C isfused for 2 amps.

CFR-90 Plus SeriesCFR-102-5-240 — 121-100-8802







Date post:	08-May-2023
Category:	Documents
Upload:	khangminh22
View:	0 times
Download:	0 times

FC-40 Plus Series - IndustryNet

Documents