RICHARDSONPROJECTS(PVT.)LTD
NetTrollInstallationManualVersion1.7
ThilinaRajapaksha
3/26/2014
[This document includes summarized steps involving in setting upNortroll conductormounted faultindicators in the fieldand in the controlPC. It is important that yougo through theUsermanualofNorTroll,priorreadingthis.AuthorassumesthatthereaderhasgonethroughNortrollusermanualsandtosummarizethesettingupthissummaryguideisprepared.]
2
ContentsSection01:HardwareConfigureofLT110Eur..............................................................................................41.1. EquipmentRequired.....................................................................................................................41.2. SettheDIPSwitchsettingsasyourequired.Pleasecontactifyouneedanyhelp......................41.3. PoweruptheCmT333ICUbyconnectingthebattery.................................................................61.4. Testifthe3/6/9indicatorsworkbeforemounting......................................................................71.5. MounttheDevices(KeepthemONwhenyouconnect,noneedofdisconnectingthem...........71.6. TestthedevicesagainfromtheControlBoxfixedbelowthepole..............................................71.7. Oncethesetupisset,dothefollowingonthe115Collector.......................................................81.8. Indicatorswillrespondasfollows:................................................................................................81.9. Batteryused..................................................................................................................................9
Section02:SoftwareConfigurationofLT110Eur........................................................................................102.1. AddGSMdevices........................................................................................................................102.2. SetthefollowingSettings...........................................................................................................102.3. AddingofFPIintheNetDrawSystem.........................................................................................102.4. SettingDeviceProperties............................................................................................................112.5. ChangingtheInputNames..........................................................................................................132.6. SettingAlarmOption(IntegratingwithNetAlert)......................................................................162.7. SettingAnaloginputProperties:.................................................................................................17
Section03:SIMCriteria..............................................................................................................................183.1. InstallationofNetTrollinWindows7machines........................................................................18
Section04:InstallingLT3100faultindicator...............................................................................................204.1 DefaultSettings...........................................................................................................................204.2 TestSequence.............................................................................................................................204.3 CommandsandResponses.........................................................................................................20a) SetRecipientNumbers................................................................................................................20b) OtherCommands........................................................................................................................21
4.4 120GLMmessagemeanings......................................................................................................224.5 SettingupinNetTrollsoftware..................................................................................................23a) AddNode....................................................................................................................................23
3
b) SettingConfiguration..................................................................................................................234.6 Batteriesusedin120GLM..........................................................................................................234.7 120GLMfirmwareupdating.......................................................................................................244.8 LT3100BatteryReplacement.....................................................................................................25
Section05:NetDraw...................................................................................................................................265.1. AddingSymbolinNetDraw.........................................................................................................265.2. Adding330RTUinNetDraw.......................................................................................................275.3. Adding333ICUinNetDraw........................................................................................................28
4
SettingupLT110EurSection01:HardwareConfigureofLT110Eur
1.1. EquipmentRequired.a. Controlboxincludes
ComTroll115Collector ComTroll333ICU SolarPanel 12VDCbattery SunGuardUnitforprotection.
b. Indicators LT110Eur
1.2. Set theDIPSwitchsettingsasyourequired.Pleasecontact ifyouneed
anyhelp.
BeforeMountingontheconductor:
When Reset Indicator Yellow LEDwill blink for 3minute.
Aftermounting(andEnergizedtheLine): IndicatorsGreenLEDwillBlinkforfewminute.
5
DependsontheFaultcurrent,Loadcurrentatdaytime,nighttime.UsuallywesetforDi/DtandnotthethresholdbecauseithashighersensitivitythanselectingThresholdtodetectfault.Selecting Threshold was used before the Di/Dtdetecting technique available. Hence itsrecommendedtouseDi/DtoverThreshold.
Usually we select Voltage. If the pole has aanotherline(maybeLVline)connectedbelow,itsrecommendedtoselectCurrentastheStart/Stopcriteriatoavoidinducedvoltagescausingerrors.
Selectminimum so the Indicatorbatterywill lastlong.UsuallyiftheschedulingofrepairstaketimeitsbettertoselectlargertimeasTimerReset.E.g.:Duringnight if faultoccursand there isnoway to attend to the repair, it will keep ondisplaying erroruntil crew goes there.But itwilldrainthebatteryfast.EnableResetonreturnofVoltage/Current returndependingontheDip4setting.
Select Remote Programming enabled. Sowe canprogram through theCollectorwithout removingfromtheIndicatorsfromtheline.
6
1.3. PoweruptheCmT333ICUbyconnectingthebattery.
SettingupofComTroll333ICU
a. RemovethePowerandconnecttheSIMandFixtheGSMAntenna.b. PowerONtheICUbyconnectingthePower.c. SettingupoftheMobilePhone
SendaSMStotheICU12340MyPhoneNumberT.Tcanbeanumberfrom19.NormalResponse 3001TErrorResponse 3000T
7
1.4. Testifthe3/6/9indicatorsworkbeforemounting.Beforefixingthemonthepolecheckthedevicescommunicationandthetestwearegoingtocarryoutoncethedevicesinstalledinthefield.(RefertestproceduresmentionedunderpointE)1.5. Mount the Devices (Keep them ON when you connect, no need of
disconnectingthem.ItsrecommendedtouseafirmConnectingRod,but itseasytodeenergizethe lineandmountthemmanuallybyhand.Alsothere isapossibilityofdevicefallingwhenyoutrytomount itusingoperatingRod.1.6. TestthedevicesagainfromtheControlBoxfixedbelowthepole.YoucandothisonceallindicatorsaremountedontheLinefromthebelowControlBox.
8
1.7. Oncethesetupisset,dothefollowingonthe115Collector
a. SettheSameDipSwitchSettingasinthefaultIndicator.OnlyDip8mustbekeptatOFF.b. ResettheCollectorfromtheResetCollectorButton.c. ResetRemoteButtonhas3functions.
YoucanexecuteFunction1: PresstheResetRemotebuttonfor0.5s2s
YoucanexecuteFunction2: PresstheResetRemotebuttonfor2s4s
YoucanexecuteFunction3: Press theResetRemotebutton formore than4s.We canuploadnew
settings without changing the dip setting of the Indicators if their(Indicators)Dip8isatON.
1.8. Indicatorswillrespondasfollows:Indication Conclusion
a) The yellow and green LED (on theindicators)willflashsimultaneously.
Wecanconclude that fault indicatorDIP8 isOFF,theindicatorcannotberemotelyprogrammed.
b) The yellow and green LED (on theindicators)willflashalternating.
We can conclude that fault indicatorDIP8 isON,theindicatorisreadyforremoteprogramming.
Pointa)andb)willbeindicatedfor9seconds.c) ThegreenLEDontheindicatorwillflash. Lineisenergizedd) The indicator the yellow LED on the
indicatorwillflash.Line isdeenergized.This iswhatshownwhenweresetthedevicesbeforemounting.
Pointc)andd)willbeindicatedfor3minutes.
9
1.9. BatteryusedKBB 11 battery for the conductor mounted unit. ItshouldnotbereplacedwithKBB20.
10
Section02:SoftwareConfigurationofLT110Eur2.1. AddGSMdevices.
RightClickontheGSMdevices>Addnode>followmanual.
2.2. SetthefollowingSettings.
a. SetGLRnumber(shouldgetanacknowledgementfromdeviceinRed)b. SetConfigureNode(ShouldgetanacknowledgementfromdeviceinRed)c. SetActiveTimeforRelay(ShouldgetanacknowledgementfromdeviceinRed)d. SetHeartBeatInterval(ShouldgetanacknowledgementfromdeviceinRed)e. ChangerespectiveDigitalInputsasPhase1,2,3Ok/FAULTandalsoBattery/communication
OK/FAULT.Note:when giving phone numbers always use +94 instead of 0. Now you can test the devicesthroughNetTroll.Asthefirststepwewilladdallthemounteddevicestothesystem.OnceitisdonewecanaddthemintherespectivelocationintheSingleLineDiagramforVisualindication.2.3. AddingofFPIintheNetDrawSystem
1. Draw3bmpwith size21by21pixelsand save them in theBitmap folder in the installationdirectory.
2. Renameasa. FPIAA000.bmpNormalStatusb. FPIAA001.bmpAlarmStatusc. FPIAA255.bmpUnknownStatus
3. DrawsimilarlyfortheLowBatteryandComm.Fail3symbolsa. LBACF000.bmpNormalStatus(Keepthecolorbackgroundsoitsnotvisibleduringnormal
operation)b. LBACF001.bmpActiveStatusc. LBACF255.bmpUnknownStatus
4. OpentheSingleLineDiagramfromNetDrawandaddoneofthebitmaps.Copyandpastetheremaining2forindicating3phasesinthesingleFeeder.
5. SavethedrawingasthecorrectSubsystem.6. OpenthedrawingintheNetTroll7. PressRightClickwhilepressingCtrlandShiftandRightClicktoaddtheICUDigitalInputtothe
symbolsintheNetDraw. 8. CheckwhetherGSMisdisabled.ViewOptionsUntickDisableGSM
11
2.4. SettingDevicePropertiesDoubleClickonthe333ICUthatweareabouttoconfigureSelectAdvanceTab1. SetGLRnumber(introduceGLRnumbertothefielddevices+94XXXXXXXXX)2. ConfigureNode
a. AddGLRnumberb. ConfigureNode
i. EitherbyPhonesendingPassword1EBCDATii. FromSCADAEBCDA(usuallyweput01111butitcanchangeaccordingtoyoursetup)
12
3. SetRelayTimeoutforrelay1to4(ActiveTimeforRelay)
4. SetHeartBeatIntervalinhoursSetatahighervalueforlessbatteryusage.4digitsareusedalways0072default
5. ChangePassword
13
2.5. ChangingtheInputNamesTherearebasic2wiringofdigitalinputsbeingdeployedinCEB.Old(2011)
New(LatestinR2andR3since2012)
14
EachDigitalinputin333ICUand330RTUcanberenamedasrequiredtoshowintheNetTrollMainLog.DoubleClickontheDevice>Advance>Config>ThisDevice>Get>followingwindowwillappear
Note1:Ifdoingforaparticulardeviceforthefirsttime,thenselectThisdevicetype.Note2:OnceonedevicesdigitalinputsarecorrectlyconfiguredyoucouldcopytheinputnamingandalarmsettingbyselectingAnotherdeviceandselectthedeviceyouwanttocopysettingfrom.BUTnotebasicsetting(SetGLR,confignode,etc)hastobedoneonceaddedmanually.Makesureyourenamethecorrectdigitalinputbylookingatthewiringdiagramofthecommunicationdevice.OlddevicesinputshastobenamedasOldWiring NewWiringDigitalinput1=Phase1 Digitalinput5=Phase1Digitalinput2=Phase2 Digitalinput4=Phase2Digitalinput3=Phase3 Digitalinput8=Phase3Digitalinput4=battery/Communicationfail Digitalinput6=battery/CommunicationfailBattery/Communicationfailalarmcouldcomedueto
1. LossofradiocommunicationbetweenCmT115collectorandLT110EurfaultIndicator2. LowbatteryoftheLT110Eurfaultindicator.
15
Eachdigitalinputmustbecorrectlyassignedtoavoid,anyconfusionandmisinterpretation.
Alarmsettingforfault
Alarmsettingforphaseok
RTUOKmessagealarmSetting
16
2.6. SettingAlarmOption(IntegratingwithNetAlert)
a. GotoView>AlarmOption>SetAlarmwhenuserloginb. GotoeachalarmsandsetAlarm
17
2.7. SettingAnaloginputProperties:All four Analog inputs can be set up toaccommodate following rangesindividually
a. 010Vb. 420mA
Allinputshave10bitresolutionRawvaluecanbe intherangeof01024.ICU sends the raw values and must beconverted into unit matching themeasuredvalue inNetTroll.FollowingarebasedonNetTroll4.0.
a. GotoAdvancedMenu.b. PressSCALEbutton
ExamplePrimary Secondary0250A 010VDipSwitches:No1,No2:SETtoOFFNote: If Secondary is measuring CurrentDip3,4issettoON.ButinyoursetupwearemeasuringVoltage.SettingAnalogchannelsarenumberednotinthewayitsshown.Seethefigurebelow.
18
Section03:SIMCriteria
1. Tofindthetypeofsubscriptionthatismosteconomicandsuitableforyoursystem,pleasecontactyourlocalnetworkserviceprovider.
2. Wedonotrecommendusingprepaidsubscriptions.3. Voiceservicesshouldnotbeavailable.4. GSMdata(CSD)enabledandSMS.5. CLIP(CallerID)mustbeenabled.6. AllPINcodesmustbedeactivatedbeforeinstallation.SomeserviceprovidersofferSIMcards
wherethePINcodesaredeactivatedwhenyoureceivethem.HowtoDeactivatethePIN;
7. IftheSIMcardhasthePINcodeactive,itmustbedeactivatede.g.byinsertingitinamobilephonefirst.
8. ThebatteriesshouldbedisconnectedbeforetheSIMcardisinserted.9. Wesuggestthatalabelmaybeattachedonthebracketwherethetelephonenumberisvisible
fromtheoutside.10. IfaGLMisprogrammedwithoutusingthecountrycode,andtheGSMnetworkaddthecountry
code,Nettrollwillnotrecognizethemessage.Therefore,countrycodeshouldalwaysbeusedwhenprogrammingGSMunitsinNetTroll.
3.1. InstallationofNetTrollinWindows7machines
YoucannotruntheLNSona64bitplatform.Youneed32bitinordertomakethePCLTAcardwork.Echelonhasunfortunatelynotcomeupwithsupportfor64bitoperatingsystem.DonotinstalltheNetTrollprograminthedefaultcatalog(c:\programfiles\....)asthiswillmakechangesdifficult.TherearesomerestrictionsinaccessontheProgramFilescatalogs.InstallNetTrollinc:\Nortroll\....instead.Theordershouldbeasfollows:1:InstallthedriverforthePCLTAcardbeforeinstallingthecardphysicallyinthecomputer.2:SwitchPCOFFandinstallthecard.3:PowerthePCup.Itshouldnowdetectthecardandstartinstallingit.Thiscantakeseveralminutesopleasebepatient.4:RestartthePCwhenthedriver/cardisproperlyinstalled.5:InstalltheLNS(YoucanusethedefaultcatalogsfortheLNS6:RestartthePC7:InstallNetTroll
19
PleasemakeabackupoftheolddatabasebeforeyouscraptheoldPC.ThiscanbeimportedintothenewPCassoonasNetTrollrunsagain.
20
Section04:InstallingLT3100faultindicator
4.1 DefaultSettingsIt isnotnecessarytosetupanythingexceptforthereceivingtelephonenumber.Changingthedefaultsettingsandprogrammingthereceivertelephonenumberaredoneduring installation inNetTroll.Alternatively,amobilephonecanbeusedtomanuallysendtheconfigurationsettingsinSMSmessages.
a.Heartbeatinterval Default:144hb.Pollinginterval Default:24hc.Password Default:kgsmd.Receiversphonenumber.Default:N/A
YoushouldthereforeconnectthebatteriesoftheindicatorbeforetheGSMmoduleispoweredupandconnectedtotheLineTroll.
4.2 TestSequenceYoushouldthereforeconnectthebatteriesoftheindicatorbeforetheGSMmoduleispoweredupandconnectedtotheLineTroll.
4.3 CommandsandResponses
Thepasswordisnotcasesensitive
TIDisaTransactionIDthatisarunningnumberbetween1and9assignedbythetransmitter.
a) SetRecipientNumbers
21
b) OtherCommands
22
4.4 120GLMmessagemeanings
23
4.5 SettingupinNetTrollsoftwareCheckiftheGSMdevicesareenabledinOptions>Generalsa) AddNode
b) SettingConfigurationClickonthenameofthedeviceandgototheadvancedtabintheDeviceControl.
SetReceiverPhoneNumber:
TheComTroll120GLMmustbetoldwheretosenditsalarms.ThereceiverphonenumberinaNetTrollinstallationisalwaystheGSMLonRouter(GLR)number4.6 Batteriesusedin120GLM
.
24
KBB11batteryfortheconductormountedunit.ItshouldnotbereplacedwithKBB20.KBB20 isused topowerGSMmodem since itcandeliverpulsatingcurrentup to2AGSMmodem ispoweringup
4.7 120GLMfirmwareupdatingSpecialtoolhastobeusedinfirmwareupdatingin120GLM.Toolisshownbelow.
25
4.8 LT3100BatteryReplacement
26
Section05:NetDraw5.1. AddingSymbolinNetDrawItem ProcedureLT3100 Digital16state>Indication:I/Ostatus.CmT333ICU Digital2state>IndicationDigitalInputXCmT330RTU SwitchstatusandRem/Off/Loc>Digital4state
Digitalinputs>Digital2state.
27
5.2. Adding330RTUinNetDraw
28
5.3. Adding333ICUinNetDraw
1. Draw3bmpwith size21by21pixelsand save them in theBitmap folder in the installationdirectory.
2. Renameasa. FPIAA000.bmpNormalStatusb. FPIAA001.bmpAlarmStatusc. FPIAA255.bmpUnknownStatus
3. DrawsimilarlyfortheLowBatteryandComm.Fail3symbolsa. LBACF000.bmp Normal Status (Keep the color background so its not visible during
normaloperation)b. LBACF001.bmpActiveStatusc. LBACF255.bmpUnknownStatus
4. OpentheSingleLineDiagramfromNetDrawandaddoneofthebitmaps.Copyandpastetheremaining2forindicating3phasesinthesingleFeeder.
5. SavethedrawingasthecorrectSubsystem.6. OpenthedrawingintheNetTroll7. PressRightClickwhilepressingCtrlandShiftandRightClicktoaddtheICUDigitalInputtothe
symbolsintheNetDraw. 8. CheckwhetherGSMisdisabled.ViewOptionsUntickDisableGSM
Note:PleasereferNetDrawusermanualforfurtherinformation