EXPERIM ENTS OF THE STRENGTH OF BOLTS AND SCREW S
BY
JONATH AN HUNTOON SAM U ELS HODGSON
B E R T AN D REW M ILLER
TH ESIS FOR THE DEGREE OF BACH ELOR OF SCIENCE
IN M ECH AN ICAL ENGINEERING
IN T H E
COLLEGE OF ENGINEERING
O F T H E
U N IV ER SITY OF ILLINOIS
JUNE, 1 9 1 0 ✓ */
UNIVERSITY OF ILLINOIS
May 31 1910 190
THIS IS TO CERTIFY THAT THE THESIS PREPARED UNDER MY SUPERVISION BY
Jonathan Huntoon Samuels Hodgson and Bert Andrew Miller.....
Experiments on the Strength of Bolts and Screws ENTITLED............................................................ .......
IS APPROVED BY ME AS FULFILLING THIS PART OF THE REQUIREMENTS FOR THE
Bachelor of Science in Meohanical EngineeringDEGREE OF----- -----------
h e a d OF DEPARTMENT OF....Mechanical Engineering
1 6 7 3 5 7
==ll
*********** t a b l e o p c o n t e n t s**********
Introduction......................... Page 1
Test Pieces and Testing*• ........... * 2
Data*............................... • • • " 6
Conclusions*........................... " 11
Tables................................. * 13
Photographs* ......................... * 16
Curves 21
1******* **INTRODlJCTION»********
In this oountry very little has been done on the strength of bolt threads. A. L. King made some experiments on the tensile strength of screw threads, an account of which appeared in the American Machinist of August 13th, 1896. His work was confined to comparison of different types of thread made by other methods, which was the plan followed out in this thesis. His results showed that; (1) when subjected to plain tension the different types of screw threads were stronger than the plain bars of the same area of cross section by about fourteen (14) per cent, (3) no very marked difference in the strength of the different styles of threads appeared; the perfectly sharp groove, being slightly stronger than the others which were grooves of round and flat bottoms, (3) the weakening effect of the turning of the nut under stress was in the one inch bolts twenty per cent, and in the one half inch, about fifteen per cent, (4) in general, it may be said that the turning of the nut upon the bolt at rupture reduces the strength of the net section thirty per cent.
The object of this work is to give the comparative strength of three different kinds of threads, viz: die-cut, machine-cut, and rolled, using bolts one half, three quarters, and one inch in size for each make of thread. The tests were to determine the strength of bolt in static tension and the shearing strength of the thread. All cut threads were U. S. Standard, and the rolled threads were as nearly like them as was possible to get them.
2The die and machine cut threads are the commonest
type of thread and, are most used in practice. The die-cut, since it is cheaper, is used where workmanship and cost enter into consideration, while the machine-cut thread is adapted to work where accuracy and smoothness are required, regardless of the cost of production. The rolled threads are made extensively for track bolts and rough work where the size of the shank does not make an appreciable difference. The general practice does not seem to take into account the strength of the rolled thread but simply the cheapness of the bolt and the adaptability to rolling the form of bolt required.
********TEST PIECES AND TESTING********The material for the bolts and threads of the die~and
machine-cut type was ordinary soft steel bought in the openmarket. The specimens were obtained from different bars and as
s t r d f l g l f j sa result the Ptydaocs were not the same in all cases. The stock, being cheap, was not uniform in size and it was due principally to this fact that the threads were not perfect in every case.The machine-cut threads were made as smooth as possible. No half-inch lathe cut bolts were tested on account of the difficulty in cutting so small a bolt in the lathe. The die-out threads were turned out in the thread cutting machine in the shops of The University of Illinois. The dies were not very sharp but were as good as would ordinarily be found in practice. The rolled threads were obtained from the Oliver Steel and Iron Co. of Pittsburg, Pa. The process in the manufacture seems to be the passing of heated stock between two dies that move in opposite directions and at the same speed, thus causing the stock to
5rotate but not to have translation. The threads are simply squeezed into shape by diagonal thread forming projections on the dies which works the material so that its strength is increased. The nuts cannot be rolled in the small sizes.
All of the specimens, except the rolled stock, were two feet long with each end threaded. One end was tested for tensile strength, the other for shearing strength of thread.The rolled stock was about eighteen inches in length with approximately the same number of threads. For the shearing tests the specimens were set up in a lathe and centred as true as possible. The threads were then turned off at the root except for about two whole threads. Calculations showed that under ordinary
T L a i v d L f r i M , t io J lw - Z Z b
stresses for mild steel that about sixteen hundredths of an inchA
was about all that would shear, while in the three quarters inch eighteen hundredths could be used, and for the one inch twenty- one one hundredths of an inch was necessary.
A system of classification of specimens was deemed0
necessary and the following was adapted. The identification mark gives the number of the specimen, diameter of the stook, and the kind of thread; as for instance, 2-5/4-M would mean specimen number two of the three-quarters inch machine cut thread. D and R were used for the die and rolled threads respectively. From the tabulated data it will be notioed that the one half inch die cut specimens begin with the number 4-1/2-D. This is because the first three specimens were discarded on account of the inaccuracy of the root diameter measurements. The anvils of the micrometer did not fit the V shaped thread. Thereafter an ordinary clamp caliper was used.
4Nearly all the tests were rade in a Riehle testing
machine, having a oapaoity of 100000 pounds. The tests were run at slow speed until the yield point was passed and then high -speed used till rupture occurred. little trouble was encountered with the eighteen inoh rolled specimens. The head of the machine was so thick that not enough material was left to allow for attaching the instruments. A head made of two and one quarter inch slabs of steel was fitted to a 100000 pound Philadelphia testing machine and this machine used for the tests of short bolts.
Two extensometers were used to get the extensions.They were of the wire-wound drum type, reading to ten-thousandths of an inch. The other instruments used were miorometer calipers for the shank of the bolt, thread calipers reading accurately up to one- hundredth of an inch, and some tools such as wrenohes and hammers for marking test pieces.
It was intended to get the elongation in the thread by the use of the two extensometers. One was to record the elongation in the known length of the shank and the other, the elongation in the part of the thread in tension and a part of the shank. Then knowing the elongation in inohes per inch from the first extensometer and the length of the shank above the second extens- ometer, the elongation in the thread could be calculated by subtracting the elongation in the shank from the total elongation as recorded by the second extensometer. This was very good intheory but the length of the thread in tension was so indefinite
resultsthatAas much as twenty five per cent too great or too small were possible since a part of the stress was in the nut as was plainly
5evidenoed on examination*
A description of the actual carrying out of a tension test will not be amiss here. The specimen was placed in the machine without the instruments and the space inside of which the recording apparatus was to be placed, was marked roughly with a piece of chalk. The root and thread diameters were measured and recorded. The stock or shank extensometer was set up in the jig whioh takes the length of stock of eight inches, and the bolt damped in. Then the second or thread extensometer was put on in the middle of the first with an ordinary damp. The test piece was then set in the machine and the nut turned on. A nickle steel washer was used between the head of the machine and the nut. This plate had two small holes drilled to permit passing a small wire over a lever fastened to the nut, for the operation of the thread extensometer. The lever and its attachments are shown in Pig. I. The lower extensometer marked I is the shank extensometer and the upper marked II is the thread extensometer. The length of shank from No. II up to the threads was measured and the lower head of the machine raised. The jaws were placed as high up as possible because of the threads on the lower end of the test piece. The bar was then aligned and a light load of about a hundred pounds put on it. The pointers were placed at zero and the test was begun, first by putting on about 1200 pounds, but after that, readings were taken at equal increments of elongation on the thread extensometer as far as the elastic limit. Readings of both extensoraeters and load were obtained, and after every third reading the strain was relieved when the extensometer release readings were taken. The instruments were taken off after the
6
elastic limit had been passed, and the load increased till rupture occurred.
In the shear tests no instruments were used because there did not seem to be any yield in the specimen, but a sudden failure. The thread diameter at the root and the length of the thread in shear were measured. The test was made on the end which had been previously prepared. The nut A, shown in figure II, was turned on till the threads to be sheared were well up in the nut. The exact position was varied in the different specimens. The bolt was then placed in the machine. The plate B acted as a washer and a head as in the tension test. The specimen was then aligned and the jaws C clamped on. The bolt was then loaded at slow speed while the poise was carefully adjusted so that any sign of yield could be noticed in the fall of the beam.
After the tension and shear tests had been pulled off, the ultimate strength of the bar was found except in the case of the rolled stook, where the bar ruptured in the tension test.For these it was necessary to drill a part of the material out of the thread and then set up the specimen as in the other ultimate tests. The part drilled out was as near the center as could be obtained with an ordinary center punch and drills.
fc*#********#*#*])^^****#^***** ******The data as compiled in Table I show£ the calculated
results for each specimen, and the averages for each classification. The blank spaces in the plate are where no definite values could be obtained from the curves. With a different selection of points on the curve this would probably not occur. There was
7some difficulty in getting the ultimate strength of the rolled threads as has been mentioned before and explained* but in the table the figures give the stress on the whole area of the root of the thread as oalculated from the reduced part under test•The results obtained are probably not widely different from what they would be if fracture had ocourred across the original area. The calculated results were used in finding the per cent strength for these threads which, in every oase, was greater than one hundred per cent.
The point of rupture in the machine and die out threads was about half way between the nut and the shank. This was not true of the rolled. They broke at the bottom of the drilled out portion. The rolled specimens were hard to handle in the ultimate tests on the threads on account of the difficulty of setting them up straight. In one case there was evidence of a little bending action. This may have been due partially to the poor bearing surface of the nut. This fact entered into the results of some of the other tests and was unavoidable.
The comparative strength of the root and shank of the thread is shown in Table II. Reduoing the load on the shank and on the thread, at the different events, to pounds per square inch shows that the stress on the smaller area is greater than that on the larger area of the shank. This seems to be an accepted fact for static tension tests. The difference in the stress on the area at the root of the thread and that on the shank is great- est for the rolled threads, the machine cut next, and the die cut least. From this, it seems that the lathe tool has something of the effect on the material that rolling has. The table also shows
8that in the oase of the rolled bolts the per cent strength is greatest at the ultimate, while for the die-and machine-out, the yield point shows the greatest per cent strength.
The shear tests brought out some important considerations in the design of nuts, including lock nuts. There is a minimum allowable thickness which may be sufficient to stand the strain on the bolt. If we assume a factor of safety of five under static loads, the following formula is derived:-
Thickness of nut
where T is the allowable stress in pounds on the bolt in tension, £> the allowable shearing stress in pounds per square inch, and Q the circumference of the root of the thread in inches. The nut must fit well in each case in order that this may hold good. Table No, III shows the thickness of the nut required to stand the strain of the threaded portion, except in the case of the rolled threads, where the threaded portion was stronger than the shank.
The efficiency of a bolt has been taken to mean the ratio of the load on the thread to the load on the shank of the bolt at the corresponding events. For instance the efficiency of a bolt at the yield point would be the ratio of the load on the thread at yield, determined from the curve, to that of the shank determined in a similar manner. It is concluded that the events on the stress-strain curves for the shank and thread are for the thread alone since the area of that section is smaller and any failure would appear in the threaded portion first. This is not exactly true of the rolled threads, but it has been assumed
9that the events on this curve were also true for the threaded part. The efficiency has been determined for each kind of thread at the elastic limit, yield point, and ultimate. Plate I gives the results of these calculations and shows that the relative per cent strengths of the rolled threads at ultimate, is much greater than the two others. The same is true of the other events. The efficiency of the one inch rolled was one hundred nineteen (119) per cent at the ultimate, while the die-and machine -cut were eighty three (83) and eighty four (84) per cent respectively.The per cent strength seems to increase with the diameter of the shank for the die and machine cut threads. This was the case in all but the machine-cut threads at yield, where it decreased slightly. In the rolled threads the one inch increased a little at the ultimate, but, for all other events on the different sizes, the curves ran about horizontal. These curves from plate I show that the rolled threads are by far stronger than the others, and that there is no choice as far as strength is concerned between the die and machine threads. The working of the metal increases the strength and this no doubt accounts for the high values in favor of the rolled threads.
Plates No. Ill---XXXI are the load-elongation curvesfor each specimen that was tested. Each curve was plotted on a separate sheet to avoid confusion, and for the reason that the curves could not be reduced to the same basis since the areas and the lengths of the threads were not uniform. The latter could not be accurately determined. The ordinates were load in pounds and not in pounds per square inch, because the ratio of the loads was wanted at the events, and by plotting the curves as they are the
10
load can be read directly. The elongations were plotted as they were read. The points of release were plotted and show definitely where permanent set began.
Johnson's method was used in determining the elastic limit, in preference to the old way of assuming the elastic limit at the point where the curve broke away from the tangent. His method is as follows; take one half of the abscissa of any point on the straight line below the elastic limit and lay it off to the right from the ohosen point on the curve. A line drawn through this point to the intersection of the given straight line with the vertical through 0 determines the position of a second line parallel with the construction line and tangent to the curve. The point of tangenoy gives the elastio limit. This is shown better on Plate III where AB represents the length from the point to the ordinate, and BC, one half of this distance laid off to the right. CO is the line through the origin and this last determined point, and EF is the line parallel to OB tangent to the curve at the point G,- the elastic limit.
The yield point was taken at the point of inflection on the curve after the elastic limit had been passed. This is not a very acourate way to determine this point, but knowing that in tension tests of soft steel the curve is horizontal at what is called the yield, this method is considered sufficiently accurate for these tests. The ultimate was simply the maximum load on the specimen.
Plate II shows the ratio of areas at the root of the thread and the shank of the bolt for the three kinds of bolts.The curves show that the ratio for the die-and machine-cut bolts
11are practically the same, but the rolled threads are from nine hundredths to twelve hundredths nearer unity. The faot that the rolled thread is not sharp but of rounding section probably accounts for this high ratio. The fact that the curves for the rolled threads decrease, and the die-and machine-cut increase cannot be taken as of any consequence. The curves if carried farther would probably become horizontal.
********** CONCLUSIONS *********Prom the results obtained in this thesis the following
conclusions are drawn in regard to the kind of thread and their respective strengths:-
(1) The ratio of the area of cross section at the root of the thread to the area of the shank is practically a constant for the rolled threads and increases slightly for the die-and machine- cut threads as the size of the bolt increases.
(2) The efficiency of the rolled thread in tension is greatest at the ultimate, and is also greater than the machine or die cut threads at any event. This efficiency decreases as the size of the bolt increases. The efficiency of the machine and die cut threads is praotioaily the same, and increases as the size of the bolt increases.
(3) The die- and machine- cut threads will stand a greater load in shear on the threads than the specimens of rolled stock because of the loose fit of the nuts furnished with this stock.The rolled bolts are not adapted to the uses that machine bolts are put to, or to any work where a close fit of the shank is re- qui red.
(4) A thickness of nut of one half the diameter of the
12stock is all that is necessary to prevent shearing in the nut for the die-and machine-cut threads while for the rolled threads a thickness of three-fourths of the stock is required.
/3
SAMPLE DATA SHEET.
SPECIMEN 3 - 1 - D.Load Total Elong- At release to Remarks,in elong- ation 500 lbs.lbs. at ion in 8 Exten someterin in. in. of No. I No. II
bar inin.
1600 .0051 .0008 Diameter at root .84"4100 .0111 .0016 Diameter of stock 1.08800 .0154 .0030 .0119 .0004 Diameter of stock11200 .0205 .0041 after rupture .96116100 .0255 .0059 Diameter at root20600 .0302 .0075 .0198 . 0004 after rupture .6924200 .0391 .0082 Length from Ext. No. I24900 .0495 .0082 up to end of thread 9.224900 .0560 .0088 .0440 .0004 Nut fit snug.25200 .0630 .008925800 .0685 .009026200 .0745 .0092 .0610 .000426800 .0810 .009327400 .0870 .009827700 .0950 .0122 .0812 .0035 Scaled slightly at bottom.28100 .1034 .020827900 .1095 .035827700 .1165 .0541 .1018 .044828000 .1308 .086128100 .1465 .112028000 .1555 .1145 .1512 .104228100 .1855 .133928200 .2100 .162529200 .2605 .1321 .2500 .169529200 .2830 .184230100 .3070 .1882 Scaled all over.31300 .3438 .2380 .3245 .204238400 Ultimate of thread.35000 Rupture.
SPECIMEN 3 - 1 - D.In Shear.
16500 Ultimate Length in shear .2"Rupture not definite as failure Diameter at root ,84
wa;s gradual • Diameter of stock 1.0Sheared nut and bolt. Nut fit snugGood clean shear • Threads near middle of nut.
TA B LE. I
T —2 — 3 4Spec/- Diam-Diam >m e n eterctat root ■
<0* 3 No. shankin in.
of thread in in
1 47-D 495 4002 5 7 D 496 4/0 .3 6-i-D 5 0 5 4/0 .4 7-i-D 494 4/0 .5 6-i-D ■503 400 .6 9-i-D 5 04 410 .7 10-i-D 5 0 0 4106 Average 4996 407/ .9 H R 446 410 .10 2-t-R 444 410f l 3-i-R 450 40012 Average 4467 406713 I-7D .742 £20/4 2-7D 745 6 2 015 3-7D 7 4 5 6 2 0/6 47-D 748 .62017 5~7 740 .62018 AVER7440 6 2 0/9 1 /~7750 .6201 0 7 7 M 7 47 .6202/ 3-7/4 75/ 6 2 022 Average 7493 .6202 3 I-7 R ..692 .630 .2 4 2 -7 R 707 .6302 5 3 7 R 702 630 .26 Average 7003 .630 [27 l-l-D ■988 .84028 7 ID ■990 .840293-ID WOO 84030 Average .9927 .84031 l-l-M .992 8 4 0322-l-M .992 .8403 3 3 l-M 993 .84034 Average 9923 .8403 5 1 - I R .923 8 3 0
3 6 7 1 7 .9 2 5 .83037 3-l-R 9 3 0 .83036 Average'9260 ,830
shank of bolt.
Ratio otareas
at root of root of thread to shank
mo20021916.1986J994.196419591562
J550.1591.15684 3 2 2435743574392429943454416438054285408.375939243869385/768576 9 4785077437 7 2 577 2 5774/7730.6670.6720.6780
J2 5 6J3 2 013204320J2 5 6.1320.13201302432043204256429930/63018.30/8305730/8.3025.30/830/8.30/83018.31/631163116.3116
3 9L/asltt limit inpoundsin the shank
in the thread
6 5 2 5 6850 5300 7800 .6840 7080 5180 7100 .6590 6750 4250 6900.6835 - - - - 5200 - - -.6320 69504/ 50 7100 6620 6400 4450 6800 .6720 7280 5300 7700 664/.8450 6800 5480 6920 [8520 6200 5900 6700
40 //Yield point
in pounds in the
shank 'thread
/2 13Ultimate
m pounds m the
12400
7885 .8285 .6980.6925 [6925 .6960/3300 6820 i ito o .6822.6830 12900 088542700 .697542200 68 9 7.828544350 7940
5800 6600 6900
shank 10470 35550 8400 56700
10900 i 8000 33700
14400[606044200/4080 L 8095
5 5 3 9 7 2 1 0 26600 .5539,7190 27000
1425014500/4450 U700
.5539.7060 553917/53 .5539.7/70 5 5 3 9 7170
Z6800
24000/8800
.5539
.5539
.5420
.5420
.5420
.7/5027/63.8125.8060
2680027800
5420 .8058
23400
91009650990095008580
960095509200
13100
13720/250Q
/335012800/3200/l500
2/500Z/00022500
2/40020200
22.50017400 23200
7990 2300022000 23500
6200
688067006900
4/00010700107801090010700
120009750
Tf/arik thread12900
5900/0900 5700 6000 5600
th read
42900 10900
6000/0900/2900
94009440950094502/1002060021/002080020600
243502080024500
14500/4450 1452044480
2820024000 24300
2820634900
257002805028300
2/250 23000 2360045300
22700
10250 8000 8000 10200
i 9040 8000* 7900* 8100 *16800
1630014800167001626016/7020000172001960018930
/ 4 15 16/ 7 /& 19 2 0 2 t 2 2 2 3 2 d 2 5Elastic limit Yield point U/l/mate \R '14It m i Areatnpoundsper \ m pounds per \m pounds per \ thread m m bad msg inch rn lhe\sq inch 'll the]sg_ inch rn the at5/as\it Yield'at shear shear shear lbs
shank W m a Jtic lim it'67/0063300.7740 - - - - .8110 9650 3755 55430
44600 5640063600 .73203310.77/0 6130 26900 432005440060600.6300\.8260 .7340 724012575 28100
45400 6740077600- - - - - .7940 \ 26300446005490063700.5970,7890.7340 45400 5465060600.6960 3 830 ',7340 469006565077250 .7260,8050.79/0
3500032/00
2360023700235704690046/0045800
3930045500
3640022/00 23400 23200 3640034600*34820 40700
3650036430
Wread422503925032180393803305033700
3705040200 392003502043500399503645039970
37/40 41500 44700 52600 46270 30150
2850032000 32780
3030025830282/02923029000275502859031290
23400/9730*38/5018710* k3660
388003350038400385703330038000382003650034600*
34/40*
367003670037/803463035/0034/50346303/080347003593033900
34/60
shank405003673034450
3570034080
3678045020 60/004430043/504335043600
30100
31/0028430308903/8003/63030450
4570037550452004282038820379204060039//033950386803650036380
36520 35370
3372022/00 34780
3395040600m o o
52/005070054900525703650048600
31230 29/00 30/40 30200 29200 298/0 29740 3855046400 3695046400 37500 4650037670
33250
34630
60200606505970060250
3545035700357003545035760397703230038/0036720
47750 4640649/00
4643036700 43300
43850 4500035900
363004405038380
363304/600 42600 40860
4/85034750 88/90
81100 155700 54000 .7760
4740047900.4605055/004740055350526/06230060/506/25061230611005985056300
54600',7/40530505346066300570006500062770
597506970050900589005860068900 56/30 65880 54600 80200*.
345305420080200*
650012060 31540 5650.2060 27400 6200 .25/2 24680
69500.6926.82681.7670 2920079300* . 8 0 5 0 . 9 9 4 0 1 / 2 / 0 * 5340 '.219034380 78300*.95/5 10001095*4640 85700 *11380 1000 \l/324480 2.3200
.964Q .9980JU 60 1 24430\.7970,408626900
.7730
.75507440.75/50754.O7498
63900*394079700* 7 m * 8/000 70/00 69600 69400
60/5068600
5360079200*[79867
.7940
.8560
.8223
.8990
.76/08720
.6440
.81203920.9327.8060.7780.839580 8 5.7830.7990
8/70 1,7840 /2000 928326020 7020 /0/00 .389425920 .603012500 .4478 27930
3970.9963.8520
.8825
.6673 8270 .8200
.7270,8340
.7697[8270
.7730.9440,9920W 5*20/00
789013500 77 5 0.8225 U700 .8270 10800 .8000 9600 .8165
.99601.1180* 6040 ,99601.053* 6600
1045*1072 .8280 .8360 .8390 .8343 .8390 .8340 .8440 33901.1925*16300
.3894 34700 28690
.447826/30 428325250 .3831 25050
25480 .32/5 24980 .4946/7400 4946 19380
20590 606733000 .659432300 5 275 31280
32/90 I8200\.7749 23500 20300 ,7/22 28520 208003594 3/550
27860
9600
200002/30016500
.95708913
.9670 1.1760*
.9795 W 70# T h e se bars w ere drilled out to m a k e th is se c tio n w e a k e r D r i l l u sed on t h e in c h w a s 5 , on in c h w a s .199.
-Pi- T~L ' s ' _ Column t$ X Colum n €fh t h is ratio-------- ctrtdnnz-
644025300.626032/00626022220
26540
TABLE IIl/2 Inch Specimen.
RolledStock
in lbc. per cq. in. in shank thread
MachinedStock
in lbc. per cq. in. in
chank thread
Die Cut Stock
in lbc. per cq. in. in
chank thread
Increase in percent strength
in lbc. per cq. inch
Rolled Mach. DieEl. Lim. 39970 46270 35020 37140 15.5 6.0Y. Point 43600 52570 36780 45020 20.5 22.8Ultimate 60250 81100 60100 69500 34.5 15.5
3/4 Inch Specimen.El. Lim. 37180 42820 28590 31290 28210 30890 15.2 9.5 9.5Y. Point 37670 46430 29740 36720 30140 35760 23.0 23.3 18.5Ultimate 61230 81000 52610 62770 48050 53460 32.3 19.2 11.3
1 Inch Specimen.11. Lim. 34160 37800 33900 36380 34630 39110 10.8 7.2 12.8Y. Point 34750 38190 35370 40860 36300 44050 9.8 15.5 21.3Ultimate 54200 79867 56130 65880 59150 69700 47.2 17.5 17.8
1
Table III
SpeoimenActual stress
on bolt In pounds
Diameter of root of thread in inches
1/2" D 9040 0,40711/2" R 9450 0.40673/4" D 16170 0.623/4" M 18930 0.623/4" R 23570 0.63
1" D 38570 0.841" M 36500 0.841" R 36430 0.83
Circumference of root, inches
Allowable shear in lbs. per sq. inoh.
Thickness of nut
ininches.
1.281 5840 0.2411.279 4890 0.3021.949 5740 0.2891.949 5100 0.3811.98 4120 0.5762.64 6440 0.4542.64 5570 0.4972.609 5300 0.531
Ratio of ioads intoo Percetlt
80
60
40
6 0
||ffl R a tio o r loads t/ma te— Ratio of loa ds40patield — Ratio o r loads at ela stic l im it
A - R o l l e d t h r e a d s
B - M a c h in e c u t th r e a d s
C - D i e c u t t h r e a d s
Plate I
•/ sD iam eter o f shank in inches
6 ~ 7 / ■ c
Z2f
Ratio o f area a t the ro o t to th a t o f
th e shank.
■7
6
^ S o lid black - R olled threadD otted black - D ie cu t th rea d Solid re d - M achine Cut th rea d
■t>
a
/
if/ .3
P l a t e H
D /am eter of shank in inches.': ' P ' 1 - g — /■o
/ooo
•05
-©-— — oe~~ ~ >1; f O --©— -e--- e-
P l a t e J Tm m m B
■ 06 07 .03Elonqation in inches.
.09
2G
Load in lbs.7000
-©------------- ------------------— — — e
%--*e WSfT
0/ 02 0*3 0 4
W - o o oJo.i ;n !n i n'
Pl a t e Wm - 9 - j r - D
Elongation in inches ■ 08
Loadmlb s .
8000
r ~ ®7000
6000
5000
4000
3000
3000
/O O O
QII
OI
Igggjg
- m
B Pff§||m m m .
0 sShth©-^or'
o r '
m i,0 3 .04. 0 ! .0 2 ■05
,o m m .Q l - " > ■ —a jgr
06 .07Elongation in in ch es
52-O
RlateJKN C E i Q -r t m >
06 09
rmjCoc>
J C
L oads in /4000
1-3000
12000
nooo
1 0 0 0 0
9000
6 0 0 0
7 0 0 0
6000
600 0
4000
3000
2000
iooo
= 0 —
<s>*
PlateJJE- f - i m m
o s 0 6 0 7f/ongatron in inches 0 6 ■09 . / c
MBb .//2
/ O
6
T
—~~G
6
•0 / .02 •03 < H
£>-©
" C T
CoOi
0S Elongation m m etres ■06
Plate JET
■09 JO
Load inM
'02. 04 ,06 <oe ,/E ioncj a t io n in in c h e s
m
Co Qb
P L A T H imN 0 - 5 - J - D
: w ,/<?
U m 'J C UX/^t & X ,
- • W f e
tCoco/di) 5-ou ^ 4//u. 5 tZ<-exsoi/li(l,
L-juid Stress.
./ 91-1 ■/ 96 3 ./ 4 * ^\./?3 -z- 1 .20 0& :J 9 / b .1 4 * 7
I. / 9 9 t ri ,J?6 3>
,/20j> . !3$3.1/64. / * b./3.10 ./ 3 1 0,/3 i o . / * ) 7. / 32 /). /32\0
y<nrV%2.CrZ>6 9fr67 2.<0Z) 6 x 3 'd 9 0 i 'd 7 0 3 O 6 (>cn)
7 4 5 *
36 40VH 601)36'X07)d b / 0d3 9 2 0 7 )7 f7 (rvi)3 5 5 0 *
<9+J. ^ Cor'd load Ltmd
TTU^ocJSTZco& /3ni t<y*-u7
3 5 m )
(o ^ Ob7S0 (,7/C j r t r t ) 6 7 ^ t
(o 9 W7inrV6X0 0
f-0J-V1fd x o ' 5~2*d 77 0 * 4 i6 d 5-25-0 9 2 3 d 97^03 -4/ *
3 2 7 07)43 fftrV 4/60Q3*97$32. 3^39701)3560Q 3 6 2 0 V 4/(rvj)
.1 3 2 . 4 .3 0 / 9 \ 732-07) 3 0 4 0 -1)7/3 5-9 3 0 / 9 /2.<fcr0 2 9 5 0 7 )4 3 3 - 9 .30/9 7/407) 2 7 7 .5-09 3 9 4 -30f % / I 'l -X V 2 790/)4 3 cn/
............
30/9 / 3 fo rd 3/407 )
, 7 6 6 7 '4 4 4 2. 2X007) 36401)•76 9 * .0 * '4 2 - 2 7 5 -01) , 36 740
j f r i o z ) 75' 2 Co
J f 3 3 d /5 3 7 d /CO 6-7)
9/00 30/od 79<rz) 3//0Z)
/VaaV «>3/ 0V t S90O
) 0 2 az) 3 3 7 OD
4-29Z) 42 .fd 9/0 0
■996 c) 9 ^ 0 4 39-0 1 J 7 0 9 0 6 0 4 9 * 0
0 6 0 1 /0 5"ozl / 1 7 7 0 / 7 V (rz )
6 9 On? 3JJ_4 (rO
I I 4 7 b "
j Ct^o^cde -L er O <S~Uc*2 CirlJ
> S d t r ^j 3 uv0 6 6 20),iz3>m> 1,7/01) l&Dcrz) 5 6 5 0 0 L.) 0°> 0V 94907) 12900 17301) /o°>07) 94407) .)0 40Z) 5450V[/zTMrf 65*00
2-//0Z) WOZ>2.0x 00 5760V 2.//0-0 499002OX0Z) 99404 7.06 at) 47970
.7 X 4 1 .4 4 9
.4 4 / * ,30/77 ,43X3 ' 30' j 443 0 •3 o/ 7\
/940d 3 2-6,02 /3 6~0d 3O70Z) 7 9407) 5/ C 07/
, 7 7 2 7 / .4 0 4 2 ,1727 ' .4 4 4 2 7 7 4 / .4 4 4 2 -
2-95-07/ 3/740 zs707> 35207) 2 X 2.<n/ 36,400
7/062- /3 2 c) 7 0 4 * /32dJ, 7490 / 2 S ' 67/
66/0 42-407) 6/30 3 96 07) 6 /01) 3 *4 0 0
.376 / .31/ 7 ■ 372^,3270 -31 '73}
/ 4400 37601J/000V 3^107))4//rO \ 390
.U S /7.720■07/7,
3374D 23 40V 3^*01) 73607) 3 WOO
2 060Z) 3/200
2H-OQ 40001)1 / 4 7 0 7 )
2-2) 01)
^ X o n c
/025'D 34000 /0700 35/00
X9*x) 2-9/&7)
! / / 0VZ)
/ x )4 6
°/74d
/097d)
7740Z) 3/900 206 °z1 37200
(iron 30900
192.07)
2- 1 7 0 7 )
/9 0 4 A ./ 94X0)
U W 6 7*1006130 6z/0d6/9(0 6 Z6<r0
5007) 04 z-0 5346.
. 53 2. O
4 6 900 67/01) 46/00 3/9900 46-000 474007-9 33D 442-ozJ 2.0 <0 cn0 4740x7 2- 4400 6'43&z)
39300 40407)
79900 is5901) 79/00 1)701) /5'0*Z) 6 3407)
/6 900 34200 Z2 9 & 4729V 2-2-Ooz) p-900
«L
£-0*7)7 /_crztd 9009 : CCi'dlentd )5 170/9'.70/so C/000 *--X449) ,.7#70290 76007 flJp 7 „ 777;70370 % 9 4 ri
774, 7/u^
/d97d S3 40d 0000 63600
65/ 7037in S@Wir\ 6 )6 $94
X00V 6O«0<) *630/OZftJ 7/600 9/5-6)90TTV 6) 3%ay * 7 0 0dozn) 6 0 400 9X02)
/02-ad 770W J730ZL 90 00
/6 Vod 0/600 2.07O0/6 30O 3-4000 2-0 5-00//Xod 49&M) 7 * 3 5 1 )76700 2./ / 07)/(, 260 43000 JLOJ/0ZL
30 2dO
SOS 73-9 i f 5*7/0 7 7 9 b *i, 73 S_ 6 2-3 k f? ,793 64/ (,t*f . 7 3 3 60/ 632- .7 3 3 72-3 U z . ,79/ 7^4 672
7(94 0 5 9 6 17 7 X 4 737612. 7 0 2 - 9 3 9 6137 0 S --77/ 7 5 $ m
370cr0 7(7001) 3* fed 675-00 3X901) 6 93C7)
3 7 / 0 V 376 crv3T£Z7tL3 9 7 3 d
<%2. * 7 3 5 72/ * 3 4 % /T7/7 *37\ — 7d0
Z-Oinpy (06 2-0z)/72<?V 6~7’0ZfZ//760X) 6 40VQ
2 1 7 4 0 X) 7 4C 3490=0 2.) 2>crx)
* 4 3 ! 7 /2- 6>*H - SZiT\ 7 9 3 f>n
*0 / 6 7*67/
3330V 60/01)2 / 6 0 t 3 7 3 0 1 )
9 4 4 0 0 50007) 4 4 3 a y 5 * 0/7)
3 5 0 0 0 b*5'0O 302-csd (0*900
3 X 7 0 * 392-C rd 37 0 7 C
9 9 0 0 60000 0(000 9/001) °/4 0* j9 9 4 0 6/001/ 7 9 0 0 *0000 925-07 5 0 0 59X 00 5/07) *10 0 0
____740*2 3 V 07) 6>2, 2 d } ?730 59000 •1 2 4 0 7 )23607) 6 </z.( 7X7/0 > 79500 2 -3 5 0 7 )2,3 707) 6 )3 0 0 \/U W X 7 9 3 0 5 2 -3 10 Z L
1 .3 0 3 <33/?i07> 5 9 50V 34600 VD30D / / J/ lrcd*o 4 07) 5L J0V 346077 50301)5(*C°D b 'lp D 34/ 40 -//20V S <6 2 -o z 1 1
..............; J 3 / Z 3 C
744\707 74 9 5 4 19 0 Z. 7 /^ * 4 3 70/ 7/1
-e— °e e-
■©■------------ — © - - ^): ./j;...,.±. ,, ;;G
JSC
T
0
Plate U K
■ 0 2 ■04 06Pfongat/on in inches ■ /6
Load in 1 0 0 0 lbsu M llllllllllilBiff
• 1-Ullilll-r 1 til [ i M |11 I ■[ 'TH- F H - f f m + f f l f I- 1 4 t - H f f l W I f ' n f f l
<02 .0 4 ,o(> 0 8 j
in in c h e s
Pla tcH Em - 3 - ^ r - R
, / g :? < r /&
TF
Load m /ooo l b s 28 ~
O
,oz 0 4 .06
E / on era t ion in inchesos
i o°J J 1
"./ ./
*Ek
PlateiJ MNQO - i-D
Load jn j o28
O2 d
20 O O
/6
1 2
8
(»
.ny_
m
02 0 4
X&ZOO■ <r • —;
.©
■06 .08 •/ . / 2EHoncjation in inches
J d
P L A T L U m
NOS-1-M
Loadin
/ c o o/bs.
2 4m — *
■06
jOj ~ ' ~ »jC?p ---------- ©
Pl a t e X X XN O . ' 2 - J - R
L6 76 .2JO J6. ' . / i 'L/ongatton m inches.