INSTRUCTIONS IVELOT Edge-lit Area Light
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
IMPORTANTREAD CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.WARNINGS: • Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.CAUTION: • For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened firmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.
1. Remove the Cover from the Pole Adapter.
2. Place the Pole Adapter and Bolster Plate up to the pole as shown in Fig 2.
3. If mounting onto a square pole, use the supplied square pole adapter plate between the Pole and Arm.
4. Line up the Pole Adapter and Bolster Plate with the Pole drilling pattern.
5. Place flat washers, lock washers and nuts on the 3/8-16 Bolts and tighten to the pole.
6. Feed supply wires from the pole through the mounted Pole Adapter.
Mounting the fixture to the pole adapter, Fig 1.
1. Feed wires from Fixture through Gasket into Pole Adapter.
2. Line up Pole Adapter and Fixture. Place flat washers and lock washers on the 3/8-16 Bolts inside the Pole Adapter and tighten securely to housing.
3. Make sure the Gasket is secure between Pole Adapter and Fixture.
4. Make necessary connections to the supply wires inside the Pole Adapter and knot wires for strain relief.
5. Replace the Cover. Tighten Screws and Secure Pole Cap.
MOUNTING POLE ADAPTER TO THE POLE MOUNTING FIXTURE TO THE POLE ADAPTER
IVELOT
Pole Adapter Gasket
Fixture
Cover Screws
Bolts
Cover
FIG.1FIG.2
Bolster Plate Pole Adapter
Cover
Cover Screws
Washer
Lock Washer
Bolts
Square Pole Adaptor
INSTRUCTIONS IVELOT Edge-lit Area Light
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
5 35/64”140 mm
4 37/64”116 mm
27/64”10 mm
FIG.3
Dimensions of the holes on PA and Bolster Plate. This template is not to scale. Please use measurements shown in Fig.3.
POLE DRILLING DETAIL
WALL MOUNTING
Mounting the universal arm on the fixture
1. Remove the Arm Cover from the Arm.
2. Feed wires from Fixture through Gasket into Arm.
3. Line up Arm and Fixture. Place flat washers and lock washers on the Short 3/8-16 Bolts inside the Arm and tighten securely to housing.
4. Feed the wires out the back of the Arm.
MOUNTING THE UNIVERSAL ARM ON THE WALL BOX
1. Separate Wall Mount Cover and Wall Mount Box.
2. Orient box so that “TOP” is on top.
3. Feed supply wires through the Gasket and Wall Mount Box.
4. Secure Wall Mount Box (such as lag bolts and anchors) to a sturdy wall. Use appropriate mounting hardware such as lag bolts and anchors with washers suitable for the mounting surface.
5. Silicone around the edge of Gasket and/ or junction box.
6. Line up Arm and Wall Mount Cover. Place flat washers, lock washers and 3/8-16 Bolts from wall bracket, inside the Arm and tighten securely.
7. Feed the wires out the Wall Mount Box Cover.
8. Bring fixture up to the Wall Mount Box and slide the stainless steel Tether from the fixture into the Key Hole Slot for hands-free wiring. Connect the supply wires to the fixture wires.
9. Check that Wall Mount Cover Gasket between Wall Mount Box and Wall Mount Cover is secure, and screw the cover on box using four screws.
10. Replace the Arm Cover.
11. Tighten Plugs and apply weatherproof silicone sealant to all unused conduit entry points. Use weatherproof silicone sealant between wall and Wall Mount Box.
Wall Mount BoxArm
Wall Mount Cover
Bolts
Arm Cover
Fixture
FIG.4
INSTRUCTIONS IVELOT Edge-lit Area Light
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
FIG.5
FIG.6
SLIPFITTER MOUNTING
1. The Slipfitter fits a 2 3/8” O.D. Tenon. Place the slipfitter over the tenon and secure the fixture with 2 Set Screws on the side of the slipfitter.
2. Feed wires from Fixture through slipfitter and supply wires from Pole. Make the necessary connections in the slipfitter and knot wires for strain relief.
3. To adjust the angle of the slipfitter, remove 2 screws and the Slipfitter Cover Plate. Loosen the Locking Bolt and swivel fixture to desired angle. The graduation on the slipfitter cover plate can be used as guidelines to adjust the angle.
4. Tighten the Locking Bolt. Replace slipfitter cover plate. Tighten Screws and close the Plug.
5. Seal Plug using Teflon tape or silicone sealant.
Fixture
FixturePlugs
Slip�tter Cover Plate
Set Screw
FIG.7
0-10V DIMMABLE WIRINGUniversal voltage driver permits operation at 120-277V, 50 or 60 Hz. Units ordered with character ‘3’ are 347V 50Hz or 60Hz, ‘4’ are 480V, 50Hz or 60Hz. For 0-10V Dimming, follow the wiring directions in Fig. 8.
1. Connect the black fixture lead to the (+) LINE supply lead.
2. Connect the white fixture lead to the (-) COMMON supply lead.
3. Connect the GROUND wire from fixture to supply ground. Do NOT connect the GROUND of the dimming fixture to the output.
4. Connect the purple fixture lead to the (V+) DIM lead.
5. Connect the gray fixture lead to the (V-) DIM lead.
6. Cap the yellow fixture lead, if present. Do NOT connect.
FIG.8
INSTRUCTIONS IVELOT Edge-lit Area Light
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
DimmableDriver
LIN
EN
EUTR
AL
NEUTRAL
GRAY (-)
VIOLET (+)
LOAD
Occupancy Sensor
5E4
800.879.8585www.wattstopper.com
1r59151
DA
OL
ENI L
TUE
N)teloiv((g
rey)
18-20 AWG Solid CU Wire Only
230 VAC, 50 Hz1200W max ballast
FSP-211
DNR
G-
MID D
IM+
14-18 AWG Solid CU Wire Only
High/Low PIR
Gro
und
LED
FIG.9
FUSE WIRING
TROUBLESHOOTING
ACCESSORIES
CLEANING & MAINTENANCE
1. For single-fuse installations 120V, 277V, or 347V connect the fuse between the fixture neutral and supply neutral.
2. For double fuse installations 208V, 240V, or 480V connect the fuse between both supply neutrals and the fixture neutral.
1. Check that the line voltage at the fixture is correct. Refer to wiring directions.
2. Be sure the fixture is grounded properly.
3. Is the photocell, if used, functioning properly?
4. Check if the fuse has blown out.
•IVA-SF - Single Fuse for 120V, 277V, or 347V
•IVA-DF - Double Fuse for 208V, 240V, or 480V
•IVA-SPU - 10kV Surge 120V & 277V
•IVA-SP3 - 10kV Surge 347V
•IVA-SP4 - 10kV Surge 480V
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
1. Clean acrylic lens with non-abrasive acrylic cleaning solution.
2. Do not open fixture to clean the LED. Do not touch the LED
0-10V DIMMABLE WIRING WITH WATTSTOPPER SENSOR
Universal voltage driver and Wattstopper Sensor permits operation at 120-277V, 50 or 60 Hz. For 0-10V Dimming with Wattstopper, follow the wiring directions in Fig.9.
1. Connect the black fixture lead to the LOAD of Wattstopper Sensor.
2. Connect LINE of Wattstopper Sensor to LINE supply lead.
3. Connect the white fixture lead and NEUTRAL of Wattstopper Sensor to the COMMON supply lead.
4. Connect the GROUND wire from fixture and Wattstopper Sensor to supply ground. Do NOT connect the GROUND of the dimming fixture to the output.
5. Connect the purple fixture lead to DIM + of Wattstopper Sensor.
6. Connect the gray fixture lead to the DIM - of Wattstopper Sensor lead.
7. Cap the yellow fixture lead, if present. Do NOT connect.
Easy Answersrabweb.comVisit our website for product info
Tech Help LineCall our experts - 888 722-1000
e-mailAnswered promptly - [email protected]
Free Lighting LayoutsAnswered online or by request
© 2018 RAB LIGHTING Inc.Northvale, New Jersey 07647 USA
Easy Answersrabweb.comVisit our website for product info
Tech Help LineCall our experts - 888 722-1000
e-mailAnswered promptly - [email protected]
Free Lighting LayoutsAnswered online or by request
© 2018 RAB LIGHTING Inc.Northvale, New Jersey 07647 USA
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
INSTRUCTIONS IVELOT Edge-lit Area Light
DIMENSIONAL DRAWINGS
UNIVERSAL WALL MOUNT
WALL MOUNT
SLIPFITTER MOUNT
Welcome
LCCONTROL20/D10
Controller
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
Contents Lightcloud Controller
Instruction Manual
Wire Nuts
NPT Nut O-ring
x 4 x 2
SpecificationsPART NUMBER LCCONTROL20/D10
INPUT 120-277VAC, 50/60Hz<2W (Standby - 4W (Active)
MAXIMUM SWITCHED LOAD RATINGSFor Control of Magnetic, Electronic Ballast or LED277VAC: 20A Magnetic/Resistive240VAC: 5A Tungsten/Electronic, 20A FLA/ 60 LRA, 2HP120VAC: 15A Tungsten, 1HP
OPERATING TEMPERATURE-40ºC to +40ºC
OVERALL DIMENSIONS 1.55" diameter, 5.75" length 1/2" NPT Mount, Male 16AWG pigtails
WIRELESS RANGE
Warranty is active as long as service plan is activeClass 2 IP66 Rated Indoor and Outdoor RatedWet and Damp LocationPlenum Rated
Line-of-Sight: 1000 feetObstructions: 100 feet
What You NeedLightcloud Gateway A Lightcloud installation requiresat least one Lightcloud Gateway to manage your devices.
1 (844) LIGHTCLOUDor 1 (844) 544-4825
WE’RE HERE TO HELP:
Wiring
SWITCHED NEUTRALThe “Switched Neutral” white with red stripe wire is the neutral line for the load being switched. This enables power measurement. See the Power Measurement section under “Functionality” for more information.
BLACK
WHITE/RED
0-10V DIMMING
Panel
ControllerLightcloud ™
Load
BLAC
K / H
OT
WH
ITE
/ NEU
TRAL
WHITEBLACK
RED
WHITE
PURPLEGRAY
PURP
LEG
RAY
Setup & Installation1
OFF
WARNING
OFF
Turn off power
Find a Suitable Location1a
Use these guidelines when installing devices:• If there is a clear line of sight between two Lightcloud devices, they can be placed up to 1000 feet apart.• If the two devices are separated by ordinary drywall construction, try to keep them within 100 ft. of each other.• Brick, concrete and steel construction may require additional Lightcloud devices to go around the obstruction.
Lightcloud Gateway
<= 100 ft.
Add an additional Lightcloud Device to extend network range around corners B R I C K ,
CO N C R E T E O RM E TA L WA L LD RY WA L L
O R S I M I L A R
Setup & Installation (cont’d) 2 Install your Lightcloud Controller
0-10V DIMMING
NOTE: The National Electrical Code requires that low-voltage wiring used in the same enclosure as high-voltage wiring have an equal or better insulation rating. You may need to complete your low-voltage wiring in another enclosure or use a partition.
0-10V is a common method of low-voltage control of dimmable drivers and ballasts. Purple: 0-10V positive | Gray: 0-10V common
2a Install at a Junction Box (Indoor/Outdoor)
ControllerLightcloud™
RED
WHITE
WHITE
BLACK
GRAY
PURPLE
WHITE/RED
To Load
To P
anel
To D
river
/Ball
ast
2b At Lighting Panel or Trough
Space and code allowing, you may install Lightcloud devices directly in your breaker box or lighting panel. Alternatively, break out lighting circuits and install Lightcloud devices in a separate trough.
WHITE
BLACK
Setup & Installation (cont’d) 3 Labeling your device
CO N T R O L L E R DE VICE IDs
For setup and maintenance, we provide two Lightcloud Device Tables with the Gateway: one that you can attach to your panel and one to hand off toa building manager. Attach the Device Identification stickers included with each device to a row, then write in additional information, such as Zone name, Panel/Circuit Number, and whether or not a zone uses dimming.
Your Site Name
ZONE NA ME PANEL / CIRCUIT # DIMMING
Front Desk 2
DE VICE ID
1
1
2
3
To add new devices to your Lightcloud network, call RAB at 1 (844) LIGHTCLOUD, or email us at [email protected].
4 Power up
Solid GREEN when connected to your Lightcloud network. Blinking RED when not connected. The device will automatically continue trying to connect to a networkin Setup Mode.
Illuminates when the device receives a message and indicates the strength of the signal. 3 - Best signal2 - Acceptable signal1 - Unacceptable signalConsult the “Finding a Location” sectionfor more information
5
STATUS INDICATOR
SIGNAL INDICATOR
Confirm Device Connectivity
• Illuminated when device is powered• Press once to highlight this device in the
Lightcloud Application• • Press twice and hold to set dim level
Press twice to toggle circuit on and off
• Press and hold for 10 seconds to remove this device from a Lightcloud network
• Blinks when device is indicated from the Lightcloud Application
DEVICE IDENTIFICATION BUTTON
Confirm Status Indicator is Solid Green (see details below)
ControllerLightcloud ™
Log on to www.lightcloud.com or call 1 (844) LIGHTCLOUD6 Commission your devices
FunctionalityConfiguration
Operating Modes
All configuration of Lightcloud products may be performed using the Lightcloud web or mobile application, or by calling RAB.
CONTROLLER Provides switching and dimming for a single zone
TRIGGER Detect when an attached circuit is open or closed. For example, you could attach the Controller in Trigger mode to an existing occupancysensor to allow your Lightcloud system to react to the sensor.
GRAY
ControllerLightcloud™
Load
ExistingOccupancy
Sensor
WHITE
WHITE
BLAC
K
BLACKBLACK
BLACK
RED
PURPLE
RED
WH
ITE
WHITE
WHITE/RED
1 (844) LIGHTCLOUDor 1 (844) 544-4825
WE’RE HERE TO HELP:
Any wires not in use must be capped offor otherwise insulated.
REPE ATER: Disables zone control and power measurement, and extends the range of your network.
POWER ME ASUREMENT: The Lightcloud Controller is capable of measuring the power usage of the attached circuit. In order to utilize this function, the neutral wire of the load must be connected to the white-red sense wire. If the Switched Neutral line cannot be used, itshould be tied to the regular neutral wires (i.e. all neutral wires joined).
POWER LOSS DETEC TION : If mains power to the Controller is lost, the device will detect this and alert the Lightcloud application.
EMERGENCY DEFAULT: If communication is lost, the Controller may optionally fall back to a specific state, such as turning the attached circuit on.
!
FCC Information:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
To comply with the FCC's RF exposure limits for general population / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications to this equipment not expressly approved by RAB Lighting may void the user’s authority to operate this equipment.
© RAB Lighting, Inc170 Ludlow Avenue Northvale, NJ 07647
Custom manufactured in China
1 (844) LIGHTCLOUD1 (844) [email protected]
Lightcloud is a commercial wireless lighting control system & service. It’s powerful and flexible, yet easy to use and install. Learn more at lightcloud.com
Controller SwitchLightcloud Controller used to switch a load without dimming.
LightcloudTM
Controller
GREY
RED
PURP
LE
WHITE/ RED
WH
ITE
WHITE
BLAC
K
120-277 VAC
Load or FixtureBLACK
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Input: 120-277VAC, 50/60Hz
Switching Capacity (Magnetic, Electronic Ballast or LED)15.5A (120-277VAC)277VAC: 20A Magetic/Resistive240VAC: 5A Tungsten/Electronic, 20A FLA/60 LRA, 2HP120VAC: 15A Tungsten, 1HP
Switched Neutral: The “Switched Neutral” white with red stripe wire is the neutral line for the load being switched. This enables power measurement.
Controller 0-10V DimmingLightcloud Controller used to switch a load with 0-10V dimming.
LightcloudTM
Controller GREY GREYRED
PURPLE PURPLE
WHITE/ RED
WH
ITE
WHITE
BLAC
K
BLACK
120-277 VAC
Load or Fixture
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Input: 120-277VAC, 50/60HzPurple: 0-10V positiveGrey: 0-10V common
Switching Capacity (Magnetic, Electronic Ballast or LED)15.5A (120-277VAC)277VAC: 20A Magetic/Resistive240VAC: 5A Tungsten/Electronic, 20A FLA/60 LRA, 2HP120VAC: 15A Tungsten, 1HP
Switched Neutral: The “Switched Neutral” white with red stripe wire is the neutral line for the load being switched. This enables power measurement.
Note: The National Electrical Code requires that low-voltage wiring use in the same enclosure as high-voltage wiring have an equal or better insulation rating. You may need to complete your low-voltage wiring in another enclosure or use a partition.
Controller Repeater Lightcloud Controller used to repeat Lightcloud mesh network signal without controlling a load.
LightcloudTM
Controller
GREY
RED
PURP
LE
WHITE/ RED
WH
ITE
BLAC
K
120-277 VAC
Input: 120-277VAC, 50/60Hz
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Advanced Trigger WiringLightcloud Controllers can receive inputs or triggers from 3rd party switching devices such as outdoor motion or light sensors.
Sample Occupancy SensorRAB Stealth STL200
Notes: A resistor or second fixture driver must be used between the Controller and Sensor. RESLC/120 for 120VAC applications or RESLC/277 for 277VAC application. The driver must be greater than 10mA.
LightcloudTM
Controller
WHITE
WHITE
GREY
RED
PURPLE
WHITE/ RED
RED
WH
ITE
BLACK
BLAC
K
Sensor
Mains Power
RESLC/XXX or Driver*
Load or Fixture
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Emergency LightingLightcloud Controllers can be used to control Emergency Lighting fed with “Always ON” Emergency Power. Upon loss of power, Emergency lighting will fail to “Full ON” light output.
Notes: In spaces where there is only one luminaire, and it is connected to emergency power, the Controller will need to be connected to a Normal Power Circuit for proper operation. Emergency fixtures with on-board battery backup don’t require special wiring.
LightcloudTM
Controller
WH
ITE
BLAC
K
WHITE
BLACK
120-277 VAC
Emergency Power
Emergency Lighting on EM
Circuit
GREY
PURPLE
WHITE/ REDRED
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Emergency and Normal LightingLightcloud Controllers can be used to control Emergency Lighting fed with “Always ON” Emergency Power. Upon loss of power, Emergency lighting will fail to “Full ON” light output.
Notes: In spaces where there is only one luminaire, and it is connected to emergency power, the Controller will need to be connected to a Normal Power Circuit for proper operation. Emergency fixtures with on-board battery backup don’t require special wiring.
LightcloudTM
Controller
GREY
GREY
PURPLE
PURP
LE
WHITE/ REDRED
WH
ITE
BLAC
K
WHITE
BLACK
120-277 VAC
Emergency Power
Normal Lighting Area
Emergency Lighting on EM
Circuit
WHITE
BLACK
Emergency Shunt On/Off
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
LightcloudTM
Controller
#5 Yellow
HOT
NEUTRAL
#4 BLUE
#3 BROWN
WH
ITE
/ RED
WH
ITE
WH
ITE
BLAC
K
BLACK
BLAC
K
Load or Fixture
120-277 VAC
LCShunt
Emergency Panel
WHITE
RED
Lightcloud Controller emergency fixture wiring withLCShunt for on/off operation.
Note: The LCSHUNT includes a 20A rated high voltage Form C (N/O+N/C) relay and is UL924 Listed for emergency lighting control applications. The LCSHUNT can bypass a line voltage switch or dimmer, ensuring that an emergency fixture illuminates at full brightness during a utility power interruption.
Emergency Shunt DimmingLightcloud Controller emergency fixture wiring with LCShunt/D10 for on/off and 0-10V dimmable operation.
Note: The LCSHUNT includes a 20A rated high voltage Form C (N/O+N/C) relay and a low voltage Form A (N/O) relay and is UL924 Listed for emergencylighting control applications. The LCSHUNT can simultaneously bypass both a line voltage switch and a 0-10V dimming signal, ensuring that an emergency fixture illuminates at full brightness during a utility power interruption.
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
LightcloudTM
Controller
GREY
GREY
PURPLE
#5 Yellow
HOT
NEUTRAL
#4 BLUE
#3 BROWN
PURPLE
WH
ITE
/ RED
WH
ITE
WH
ITE
BLAC
K
BLACK
BLAC
K
Load or Fixture
120-277 VAC
LCShunt/D10
Emergency Panel
WHITE
RED
Phase Dimming <450WLightcloud Controllers can dim phase loads using a phase dimming adapter. For loads under 450W @ 120V and 1000W @ 277V, we recommend the Ecosense Ecospec adapter.
LightcloudTM
Controller
WH
ITE
BLAC
K
120-277 VAC
ECOSENSEMAX 450W @120V
MAX 1000W @277VPART: 7000-0
Load or Fixture
Power In
Power ToFixture
Live 0-10VDCViolet +Grey -
RED
WH
ITE/
RED
PURP
LE
GREY
GREY
WH
ITE BL
ACK
RED
VIOLET
BLACK
WHITE
Phase DimmerEcosense Ecospec Linear Dimming Control Module450W MAX @ 120V1000W MAX @ 277VD
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Phase Dimming 450-1800W
LightcloudTM
Controller
WH
ITE
BLAC
KW
HIT
E/RE
D
120 VAC
PHPM-PA-120-WHPART: 6998-0
Load or Fixture
BCI-0-10PART: 6999-0
H/L
N
DH
GROUNDCONTROL NEUTRAL
ZONE IN
PURPLE
RED
BLACK
WH
ITE
ORA
NGE
GREY
BLACK
WH
ITE
WH
ITE
WHITE
Lightcloud Controllers can dim phase loads using a phase dimming adapter. For loads between 450 and 1800W, we recommend the Lutron PHPM-PA-120-WH Phase Dimmer and BCI-0-10 Ballast Control Interface.
Phase DimmerLutron PHPM-PA-120-WH120 V @ 16 A
Ballast Control InterfaceLutron BCI-0-10Control Input Voltage: 0–10 V-Control Input Current: Source 500 µACompatible Voltage: 120–277 V~ 50/60 Hz
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
Any wires not in use must be capped off or otherwise insulated. This product should only be installed by a qualified electrician and in compliance with local and national electrical codes. !
LightcloudTM
Controller
WH
ITE
BLAC
K
120-277 VAC
Plug Socket
ContactorDPDT
RED
WHITE/RED
COIL
PURP
LE GREY
WH
ITE
BLAC
K
Plug Load ControlLightcloud Controllers can control electrical outlets using a contactor.
Welcome
Luminaire ControllerLCLC3/D10
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
®
HelloLightcloud is a wireless lighting control system. The Lightcloud Luminaire Controller is a remotely controlled switching and dimming device that can be installed into luminaires.
Product FeaturesWireless Control & ConfigurationSwitching up to 3A0-10V DimmingPower MonitoringPatent Pending
ContentsActuator Module, P/N 24586
Radio Module, P/N 24572
Wire Nuts
x 4 x 2
Instruction Manual
Gasket
1.5 in
3.7 in
1.3 in
2.0 in
2.0 in
1.0 in
What You NeedLightcloud GatewayA Lightcloud installation requires at least one Lightcloud Gateway to manage your devices.
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
Specifications & Ratings PART NUMBER LCLC3/D10
INPUT 120/277VAC, 50/60Hz
CURRENT DRAW <0.6W(Standby)–1W(Active)
LOAD SWITCHING CAPACITY LED, CFL, Tungsten 120/277VAC 500W; Magnetic 120VAC 264VA, 277VAC 500VA; Resistive/Inductive 120VAC 500W
OPERATING TEMPERATURE: -40ºC to +50ºC max temp
ACTUATOR MODULE OVERALL DIMENSIONS: 3.7” x 1.5” x 1.3”
RADIO MODULE OVERALL DIMENSIONS: 2” x 2” x 1”
WIRELESS RANGE Line-of-Sight: 700 feet Obstructions: 70 feet
INDOOR USE ONLY
DAMP LOCATION
Setup & Installation1
1a
Turn off power
OFF
OFF
WARNING
Find a Suitable LocationUse these guidelines when installing devices:• If there is a clear line of sight between a Luminaire Controller and
another Lightcloud device they can be placed up to 700 feet apart. • If a Luminaire Controller and another Lightcloud device are
separated by ordinary drywall construction, try to keep them within 70 ft. of each other.
• Brick, concrete and steel construction may require additional Lightcloud devices to go around the obstruction.
Lightcloud Gatewa y
<= 100 ft.
Add an additiona l Lightcloud Device to extend network range around corners BRIC K,
CO NCRE T E ORME TAL W AL LDR YW AL L
OR S IMIL ARDRYWALLOR SIMILAR
BRICK,CONCRETE, ORMETAL WALL
Setup & Installation (cont’d)
2
2a
Install the Luminaire ControllerFor luminaires pre-installed with the Luminaire Controller, skip to Step 3.
Fixture Installation with Actuator Module Inside
If the interior of your luminaire can accommodate the dimensions of the actuator module, install the actuator module inside the housing, and attach the radio module to the outside of the housing via a knockout.
INSIDE FIXTURE
GREY
GREY
RED
PURPLE
PURPLE
WH
ITE
WHITE
BLAC
K
BLACK
MODULAR CABLE
WHITE/ RED
120-277 VAC
Load or Fixture
24586 - ACTUATOR
GREY
GREY
RED
PURPLE
PURPLE
WHITE
INSIDE JUNCTION BOX
Load or Fixture BLACK
MODULAR CABLE
WHITE/ RED
WH
ITE
BLAC
K
120-277 VAC
24572 - RADIO
24586 - ACTUATOR
24572 - RADIO
Install Luminaire3
Install the luminaire with integrated Luminaire Controller as normal, allowing for any room to accommodate the external radio module of the LCLC3/D10.
Installation with Junction BoxIf the interior of your luminaire cannot accommodate the actuator module, the Luminaire Controller can be mounted into a junction box, with the radio module always outside any metal enclosure.
INSIDE FIXTURE
GREY
GREY
RED
PURPLE
PURPLE
WH
ITE
WHITE
BLAC
K
BLACK
MODULAR CABLE
WHITE/ RED
120-277 VAC
Load or Fixture
24586 - ACTUATOR
GREY
GREY
RED
PURPLE
PURPLE
WHITE
INSIDE JUNCTION BOX
Load or Fixture BLACK
MODULAR CABLE
WHITE/ RED
WH
ITE
BLAC
K
120-277 VAC
24572 - RADIO
24586 - ACTUATOR
24572 - RADIO
2b
Setup & Installation (cont’d)
Labeling your deviceWhen installing devices, it’s important to keep track of their Device IDs, installation locations, panel/circuit #s, dimming function, and any additional notes. To organize this information, use the Lightcloud Installer Application (A) or Device Table (B).
Install the LC Installer Application:LC Installer is available for iOS and Android.
Scan & Install Lightcloud Devices:Scan each device and assign to a room. It’s recommended that each device is scanned just before or just after being wired so no devices are missed. The more notes that are given, the easier it is to commission the system.
Send to RAB:Once all of the devices have been added and organized, submit the information for commissioning.
4
4a Lightcloud Installer Application
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
Scan Device Code
Device Info
SaveCancel
Device ID 0013A20040B62A4A
Location O�ce
Zone Name O�ce Lights
Dimmable
Power Monitoring
Enter Device Information Repeat for Additional Devices
Devices
Add DeviceSend to RAB
Office Light - ID 0013A20040B62A4AController
Office Light - ID 0013A20040B62A4BSensor
Office Light - ID 0013A20040B62A4CDimmer
Office Light - ID 0013A20040B62A4DDaylight
Office Light - ID 0013A20040B62A4ETouch
Send to RAB
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
DE VICE IDs
ZONE NA ME PANEL /CIRCUIT #
Setup & Installation (cont’d)
Two Lightcloud Device Tables are provided with each Gateway: one that you can attach to your panel and one to hand off to a building manager. Attach the Device Identifi cation stickers included with each device to a row, then write in additional information, such as Zone name, Panel/Circuit Number, and whether or not a Zoneuses dimming.
Power upTo add devices to your Lightcloud network, call RAB at1 (844) LIGHTCLOUD, or email us at [email protected]
5
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
Scan Device Code
Device Info
SaveCancel
Device ID 0013A20040B62A4A
Location O�ce
Zone Name O�ce Lights
Dimmable
Power Monitoring
Enter Device Information Repeat for Additional Devices
Devices
Add DeviceSend to RAB
Office Light - ID 0013A20040B62A4AController
Office Light - ID 0013A20040B62A4BSensor
Office Light - ID 0013A20040B62A4CDimmer
Office Light - ID 0013A20040B62A4DDaylight
Office Light - ID 0013A20040B62A4ETouch
Send to RAB
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
DE VICE IDs
ZONE NA ME PANEL /CIRCUIT #
4b Device Table
Confirm device connectivityConfirm Status Indicator is Solid Green (see details below)
DEVICE IDENTIFICATION BUTTON
POWER
• Press once to highlight this device in the Lightcloud Application
• Press twice to toggle circuit on and off
• Press twice and hold to set dim level
• Press and hold for 10 seconds to remove this device from a Lightcloud network
• Lit when device is on
SIGNAL INDICATORIlluminates when the device receives a message and indicates the strength of the signal by number of blinks:3 - Best signal2 - Acceptable signal1 - Unacceptable signalConsult the “Finding a Location” section for more information
STATUS INDICATORSolid GREEN when connected to your Lightcloud network. Blinking RED when not connected. The device will automatically continue trying to connect to a network in Setup Mode.
Commission your devices
6
Log on to www.lightcloud.com or call 1 (844) LIGHTCLOUD7
FunctionalityConfigurationAll configuration of Lightcloud products may be performed using the Lightcloud web Application, or by calling RAB.
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
Power MeasurementThe Lightcloud Luminaire Controller is capable of measuring the power usage of the attached luminaire. In order to utilize this func-tion, the neutral wire of the load must be connected to the white-red neutral wire. If the white-red neutral line cannot be used, it should be tied to the regular neutral wires (i.e. all neutral wires joined).
Power Loss DetectionIf mains power to the Controller is lost, the device will detect this and alert the Lightcloud Application.
Emergency DefaultIf communication is lost, the Controller may optionally fall back to a specific state, such as turning the attached luminaire on.[ Warning: Any wires not in use must be capped off or otherwise insulated. ]
FCC Information:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential envi-ronment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try and correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for
help.
To comply with the FCC’s RF exposure limits for general popula-tion / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications to this equipment not expressly approved by RAB Lighting may void the user’s authority to operate this equipment.
It’s powerful andflexible, yet easy to use and install. Learn more at lightcloud.com
1 (844) LIGHTCLOUD 1 (844) [email protected]
© RAB Lighting, Inc170 Ludlow Avenue Northvale, NJ 07647
Custom manufactured in China
Welcome
LCDAYLIGHT
Daylight
© RAB Lighting, Inc170 Ludlow Avenue Northvale, NJ 07647Custom manufactured in China
1 (844) LIGHTCLOUD 1 (844) [email protected]
Lightcloud is a commercial wireless lighting control system & service. It’s powerful and flexible, yet easy to use and install. Learn more at lightcloud.com
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
Lightcloud is a wireless lighting control service. The Lightcloud Daylight is a remote, self-powered, open-loop light sensor that can switch and dim Lightcloud Controllers and other Lightcloud devices.
Hello
Product FeaturesWireless Sensing & ConfigurationAmbient Light SensorInnovative Self-Powered DesignNo BatteriesPatent Pending
FCC Information:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o� and on, the user is encouraged to try and correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit di�erent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC RF exposure limits for general population/uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications to this equipment not expressly approved by RAB Lighting, Inc. may void the user’s authority to operate this equipment.
Contents
PART NUMBER LCDAYLIGHT
OPERATING TEMPERATURE-10ºC to 40ºC
OPERATING HUMIDITY10% RH to 95% RH
OVERALL DIMENSIONS5.25” x 3.16” x 1”
SpecificationsUSB POWER SPECIFICATIONSNominal Input Voltage 100-240VACNominal Input Current 6mANominal Power 0.2WFrequency 47Hz-63Hz
Warranty is active as long as serviceplan is active. Indoor Rated.
Lightcloud Daylight Instruction Manual Mounting Screws
Straight & AngledMounting Brackets
Power Supply for Setup USB Cable for Setup
What You NeedLightcloud Gateway A Lightcloud installation requiresat least one Lightcloud Gateway tomanage your devices.
The Daylight is designed to remotely control one or more Lightcloud devices that are capable of switching or dimming, such as the Lightcloud Controller or Ceiling Sensor.
1 (844) LIGHTCLOUD1 (844) [email protected]
WE’RE HERE TO HELP:
Lightcloud Controller (Or similar Lightcloud actuation device)
Setup & Installation2 Contact RAB to add your Daylight
Call us at 1(844) LIGHTCLOUD or email [email protected] we'll get your Daylight device added to your Lightcloud networkimmediately. When USB power is removed, it is normal for thisLED to be unlit.
1 Plug in the Daylight device (setup only)To join your Daylight to a Lightcloud network, plug it in with the included Micro USB power adapter. The white Power Indicator will come on and the Device Status Indicator will blink red every 10 seconds until it is joined to your network. For setup purposes, you can plug the device in anywhere that’s convenient, but please stay near the location where it will be permanently installed in order to ensure continued network connectivity. Once setup has been completed, you can unplug the device and it will operate exclusively on solar power—no batteries necessary.
DEVICE STATUS INDICATOR
Setup & Installation (cont’d)
The Daylight needs sunlight to operate, and must be within range of another Lightcloud device. Direct sunlight is ideal, but indirect sunlight may be acceptable if there’s enough of it.
3 Find a Suitable Location
Example of ideal placements
3a A skylight is a great location for the Lightcloud Daylight. Be aware of where shadows will land throughout the day and position the device where it will receive the most direct sunlight.
3b
NOTE: Remember, south-facing surfaces usually receive more direct sunlight than north-facing surfaces.
SKYLIGHT
Setup & Installation (cont’d)
The Daylight includes an angled mounting bracket that can be used to maximize the amount of sunlight landing on the device’s face.
3c In some cases, you may want to use an extension of some kind (not included) to mount the device from the ceiling. Just be sure it ends up in direct sunlight as much as possible.
3d
DIRECT SUNLIGHT
Use angled bracket to get more direct sunlight
DIRECT SUNLIGHT
May need to use an extension to obtain direct sunlight
CEILING
WIN
DO
W
!
!
The Daylight must be within range of a Lightcloud device or Gateway. See “Finding a Location”
The Daylight will not act as a “repeater” to extend the range of your Lightcloud network. If you need to extend your network range, use a Lightcloud Controller or other AC-powered device.
Setup & Installation (cont’d)
4 InstallLogin at lightcloud.com and click on Devices to associate a zoneat your site. The application will show the last measured light levelso you can configure actions to take at di�erent levels. Or, simplycall or email us:
5 Configure
1 (844) LIGHTCLOUD1 (844) 544-4825
Screw the straight or angled mounting bracket to the mounting surface.
4a
Snap the Daylight onto the mounting bracket.
4b
FunctionalityOverview
DEVICE STATUS INDICATOR:• Unlit: When not powered by USB, indicates that the device is joined to a Lightcloud network and is operating normally• Solid green: When powered by USB, indicates that the device is joined to a Lightcloud network• Green blink: After pressing the Device Button, indicates that a light level measurement has been transmitted• Single red blink every 10 seconds: Not joined to a Lightcloud network• Green/Red alternating: Resetting to factory defaultsUSB POWER INDICATOR: • White: Powered by USBDEVICE BUTTON:• Press: Indicate in Lightcloud application and measure light level• Hold for 10 seconds while USB powered: Force device to leave current Lightcloud network• Hold for 10 seconds while connecting USB power: Reset to factory defaults and leave current networkDAYLIGHT HARVESTING:Daylight Harvesting is the use of daylight to o�set the use of electric lighting to light a space. If there’s enough daylight in a space, the Lightcloud Daylight can make sure the lights are turned down or o�, and turn them back on when the sun goes down. The Lightcloud Daylight automatically takes light level measurements every 10 minutes. Pressing the Device Button will make an immediate measurement. Call or email RAB, or log in to lightcloud.com to configure actions to take at di�erent light levels, such as turning o� a zone when the light level exceeds 50 foot-candles.
AMBIENT LIGHT SENSOR
DEVICEBUTTON
USB POWER INDICATOR
DEVICE STATUSINDICATOR
Welcome
LCDIMMERW
Dimmer
1 (844) LIGHTCLOUDor 1 (844) 544-4825
WE’RE HERE TO HELP:
© RAB Lighting, Inc170 Ludlow Avenue Northvale, NJ 07647Custom manufactured in China
1 (844) LIGHTCLOUD 1 (844) 544-4825
Lightcloud is a commercial wireless lighting control system & service. It’s powerful and flexible, yet easy to use and install. Learn more at lightcloud.com
Lightcloud is a wireless lighting control service. The Lightcloud Dimmer is an in-wall switch that connects wirelessly to a Lightcloud Controller to provide switching, dimming and scene control.
Hello
Product FeaturesWireless Control & ConfigurationZone Switching & DimmingDim Level IndicatorScene SelectionNightlight
PART NUMBER LCDIMMER/W
INPUT 120-277VAC, 50/60Hz, 2W
OPERATING TEMPERATURE
0ºC to 40ºC
Specifications
DIMENSIONSDimmer: 1.77”W x 2.7”H x 1.49”DFaceplate: 2.94”W x 4.69”H x 0.06”DFaceplace Bracket: 2.8”W x 4.55”H x 0.13”D
18AWG grounding; terminals supporting up to 12AWG wire
WIRELESS RANGE
Line-of-Sight: 1000 feetObstructions: 100 feet
Contents Dimmer Faceplate
Faceplate Bracket Instruction Manual
2x 6-32 1/2” Screws 2x 6-32 5/16” Screws
Wiring
BLACK / HOT
GREEN / GROUND
WHITE / NEUTRAL
PANEL
CAUTION• Use only copper wire.• Do not operate with the faceplate removed.• This product should only be installed by a qualified electrician and in compliance with local and national electrical codes.• This product should only be installed in a UL-approved single gang wall-box enclosure.• Indoor use only.
What You Need
A Lightcloud Gateway
A Ceiling Sensor (Or similar actuator)
1 (844) LIGHTCLOUDor 1 (844) 544-4825
WE’RE HERE TO HELP:
Setup & Installation
OFF
WARNING
OFF
1 Turn o� power
Finding a suitable locationLightcloud uses a wireless mesh network to connect devices such as the Dimmer to the Gateway. Unlike a WiFi router, each Lightcloud device may connect another device to the network. If there is a clear line of sight between two Lightcloud devices, they can be placed up to 1000 feet apart. If the two devices are separated by ordinary drywall construction, try to keep them within 100 feet of each other. Brick, concrete and steel construction may require additional AC-powered Lightcloud devices to go around the obstruction. See the Deployment section of your Gateway for more information.
Setup & Installation (cont’d)
2
2a
Install the Lightcloud Dimmer
Screw the line (black) and neutral (white) wires into the labeled connectors on the back of the Dimmer. Connect the ground wire (green).
2b Use the two 6-32 1/2" Phillips round head screws to secure the Dimmer to the junction box.
Make sure the arrow labeled “TOP” is pointing up.
2d Snap the faceplate onto the faceplate bracket.
2c Use the two 6-32 5/16" Phillips flat-head screws provided to secure the faceplate bracket to the Dimmer.
Setup & Installation (cont’d)
2 Install the Lightcloud Dimmer (cont’d)
Setup & Installation (cont’d)
For setup and maintenance, we provide two Lightcloud Device Tables with the Gateway: one that you can attach to your panel and one to hand o� to a building manager. Attach the Device Identification stickers included with each device to a row, then write in additional informa-tion, such as Zone name, Panel/Circuit Number, and whether or not a zone uses dimming.
DE VICE IDs
ZONE NA ME PANEL /CIRCUIT #
3 Labeling your device 4 Power upTo add your Lightcloud Dimmer to your system, enable Setup Mode via the Lightcloud application or call RAB at 1 (844) 544-4825. When the Dimmer powers up, it will automatically try to join, and keep trying until it is able to join.
If you are installing multiple devices, you may wait until they are all installed to enable Setup Mode.
When all devices have been commissioned, remember to disable Setup Mode.
ON
5 Confirm device connectivityConfirm Network Status Indicator is solidgreen (see details below).
Functionality
Overview
DEVICE BUTTON
NETWORKINDICATOR
SIGNALSTRENGTHINDICATOR
TOP BUTTON
BOTTOM BUTTON
NIGHTLIGHT
DIM LEVELINDICATOR
ConfigurationTo pair the Dimmer with a zone, assign scenes or perform other configuration, use the Lightcloud web application or call RAB:
1 (844) LIGHTCLOUDor 1 (844) 544-4825
WE’RE HERE TO HELP:
DEVICE BUTTON (press using paperclip): • Single press: Indicate in Lightcloud application• Hold for 10 seconds: Force device to leave current Lightcloud network
DIM LEVEL INDICATOR: • Displays current dim level (Zone mode)
NIGHTLIGHT:• White: Lit when zone is o� so you can find the dimmer
SIGNAL STRENGTH INDICATOR: • Indicates strength of the connection to next Lightcloud Device
NETWORK INDICATOR: • Solid green: Connected to a Lightcloud network• Blinking red: Not connected to a Lightcloud network The network and signal strength indicators are lit for 10 minutes following initial power on. To display the indicators later on, simply press the device button once.
TOP AND BOTTOM BUTTONS:Functionality depends on which mode is being used; see next page for details.
Functionality (cont’d)
FeaturesThe Lightcloud Dimmer can be used in Switch Mode, Dimmer Mode or Scene Mode. To switch between these modes and access other configuration options, use the Lightcloud web application, or call RAB at 1-844-LIGHTCLOUD.
SWITCH MODE: In Switch Mode, the Dimmer is paired with a specific zone to provide switching.Top and Bottom Buttons:• Single Press: Switch zone on/o�
DIMMER MODE: Dimmer Mode takes Switch Mode and adds dimming capabilities.Top Button:• Single press while zone is o�: switch zone on.• Single press while zone is on: dim up to max gradually, stopping at current position if bottom button is pressed.• Press and hold while zone is on: dim up gradually, release to set dim level.Bottom Button:• Single press while zone is on: switch zone o�.• Press and hold while zone is on: dim down gradually, release to set dim level.
SCENE MODE: In Scene Mode, the top and bottom buttons activate preselected scenes. This can be configured using the Lightcloud web application or by calling RAB.
FCC Information:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o� and on, the user is encouraged to try and correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit di�erent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC RF exposure limits for general population/uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications to this equipment not expresslyapproved by RAB Lighting, Inc. may void the user’s authority to operate this equipment. Custom manufactured in China.
Manual
®
Device SpecificationsPART NUMBERLCGATEWAY
ELECTRICALThe Lightcloud Gateway is designed to be hard-wired to AC power by a qualified electrician.
INPUT120-277 VAC, 50/60 Hz 60-45mA
BATTERYLi-ion battery. Contact RAB only for replacement batteries.CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO LOCAL LAWS.Some communities offer recycling or collection of rechargeable batteries— contact your local government for disposal practices in your area.
DISCONNECTAn external readily accessible disconnect device, such as a circuit breaker, is required.
Custom manufactured in China Copyright © 2016 RAB Lighting, Inc.
3
Contents IntroductionSystem OverviewLightcloud GatewayLightcloud Devices
Finding a Suitable LocationBest PracticesBest PracticesGetting Started
InstallationLightcloud GatewayLightcloud Devices & Table
SetupNetwork SetupGateway ActivationLightcloud Devices
5678
9101112
131417
18181818
4
Lightcloud is a cloud-based wireless lighting control system that makes it easy to take charge of your lighting—from sensing to dimming, schedules to scenes, and everything in between. Control and configure your system remotely using the Lightcloud Application, or call RAB to have our experts set up your system just how you need it.
Welcome to lighting control that just works.
5
System OverviewAn individual Lightcloud installation, or Site, requires at least one Lightcloud Gateway depending on the environment and usage. Your Lightcloud devices communicate with each other and the Gateway via a wireless mesh network, which allows site layout to be flexible and robust.
The Lightcloud Gateway and Devices require a subscription to function beyond the installation period. Call RAB at 1 (844) LIGHTCLOUD or visit lightcloud.com to set up your account. Your Lightcloud subscription gets you these state-of-the-art features:• Online control & configuration at control.lightcloud.com• Device commissioning• Free support• Telephone concierge• Energy monitoring
6
7Lightcloud Gateway
Lightcloud GatewayThe Gateway connects your system to our secure, private server via a cellular signal, so you don’t have to worry about providing your own internet connection. With the Gateway powered and connected, your Lightcloud site is at your command with the Lightcloud Application. For maximum security, the Gateway isn’t exposed to the internet at all, and for maximum reliability, the Gateway contains an Uninterruptible Power Supply (UPS) that will maintain power for up to 2 hours. When the Gateway is not powered or available, switching devices such as the Controller will fall back to a configurable emergency mode, such as turning on to full brightness.
8 Lightcloud Devices
L I G HTCLO U D D E V I CE S TH AT CO NNEC T TO THE G ATE WAY
Lightcloud Controller The Controller switches circuits up to 20A as well as provides a 0-10V dimming interface for dimmable drivers and ballasts.
Lightcloud Daylight The Daylight is an innovative, self-powered daylight harvesting sensor that measures available light and adjusts your lighting automatically.
Lightcloud Ceiling SensorThe Ceiling Sensor is an intelligent passive infrared motion sensor that can be configured for both occupancy and vacancy sensing. Switches up to 15A and provides 0-10V dimming.
Lightcloud DimmerThe Wall Dimmer puts advanced control at your fingertip. Configure via the Lightcloud App to switch & dim a zone or change scenes.
Learn more about Lightcloud Devices at lightcloud.com
Lightcloud Devices
9Finding a Suitable Location
Finding a Suitable Location
The Gateway should be installed in a dry or non-condensing damp environment only.
Use these guidelines when installing additional Lightcloud devices: • If there is a clear line of sight between two devices, they can be placed up to 1000 feet apart. • If the two devices are separated by ordinary drywall construction, try to keep them within 100 feet of each other.• Brick, concrete and steel construction may require additional devices to go around the obstruction.
10
Best PracticesUnlike an ordinary WiFi router, where all devices must be within range of the router, hardwired Lightcloud devices extend the range of the network—so as long as each device is within range of another, you’ll have a strong, reliable system.
NOTE: Lightcloud Daylight devices do not extend the range of a Lightcloud network.
Lightcloud Gateway
<= 100 ft.
Add an additional Lightcloud Device to extend network range around corners
B R I C K ,CO N C R E T E O RM E TA L WA L L
D RY WA L L O R S I M I L A R
M E T A L C O N C R E T E B R I C K
PRO B L E M M AT ER I A L S
Large amounts of metal, concrete and brick are bad news for radio signals; in some cases, you’ll have to go around these obstacles with additional AC-powered Lightcloud devices.
Best Practices
11Best Practices
M I C R O W A V E S
E L E V A T O R M E C H A N I C A L R O O M S
A M P L I F I E R S & A N T E N N A S
P R O B L E M D E V I C E S & S I G N A L S
Lastly, consider sources of invisible interference. Avoid placing Lightcloud devices near microwaves, motors (especially elevator mechanical rooms) or any other radio amplifiers and antennas.
Best Practices (Continued)
12 Getting Started
Getting Started
G AT E WAY
INSIDE YOUR GATEWAY
DEVICE TABLE MANUAL
ACTIVATION STEPS
DEVICE ID ZONE NAME PANEL/CIRCUIT # PWR/ENGY DIM NOTES
CONTAINS2x Wire Nuts2x Mounting Screws4x Device ID Labels 1x Power Cable*
*The Lightcloud Gateway must be mains powered for permanent installation. Power cord including for testing cellular signal strength at different locations in a facility.
Manual
®
CELLUL AR SIGNAL STRENGTH
13Installation
InstallationThe Lightcloud Gateway is rated 120-277VAC and contains an integral junction box for hard-wired installation by a qualified electrician.
POWERCELLUL AR SIGNAL STRENGTH
SYSTEM STATUS
LED IndicatorsP O W E RGreen: Fully powered
C E L L U L A ROff: No or poor cellular signal. You must move the Gate-way to a location with better cellular signal.Solid Yellow: Adequate cellular signal. This signal strength works for most applications, but if possible, move to a location with better signal.Solid Green: Good cellular signal.
S Y S T E M S TAT U SBlinking Yellow: InitializingSolid Yellow: Error: Cannot reach Lightcloud service. Check Cellular Signal Strength and call RAB for technical support.Blinking Green: Ready to connect with new Lightcloud devicesSolid Green: Normal operation
14 Installation Lightcloud Gateway
Follow instructions and steps to successfully install your Gateway.
Installing the Lightcloud Gateway
Turn off the breaker and prepare the circuit you’ll use to power the Gateway. A dedicated circuit is recommended.
Remove a knockout (KO) from the Gateway using a flat-blade screwdriver and hammer. Place the screw-driver blade at the edge of the KO, then tap the screwdriver with the hammer to weaken the attachment. Work your way around the edge of the KO until it breaks away.
Choose a location with good cellular signal. Check your phone’s signal for reference.
NOTE: Locations with significant concrete and brick construction, or underground locations, are not recommended. Do not install inside metal enclosures.
1 2 3
O FF
O FF
WARNING
S T EP O N E S T EP T WO S T EP T H R EE
3:14
15Installation Lightcloud Gateway
5
Mount the Gateway to the installation surface using size 10 screws appropriate for the surface material. For direct installation onto an external junction box, use the junction box’s included screws.
NOTE: Conduit must be used to connect to side knockouts.
4
Turn breaker back on.
O N
O N
6S T EP FO U R S T EP FI V E S T EP S IX
Install included battery with negative (-) end facing towards junction box area. Call RAB to request replacement rechargeable batteries. Use RAB-provided batteries only.
Connect hot and neutral wires with included wire nuts.
16
DEVICE ID ZONE NAME PANEL/CIRCUIT # PWR/ENGY DIM NOTES
Installation Lightcloud Gateway
Installing Lightcloud Gateway (Continued)
Turn on the Gateway mainpower switch. Replace out-er cover and use included screws to secure.
When all devices are installed and powered, you’re ready to call RAB to activate and verify your system, and complete your site’s configuration.
Confirm that the cellular signal strength LED is yellow or green. If the Gateway is powered but this LED is not lit, relocate the Gateway to an area with better reception. You can use the included power cable to easily test the signal strength in a few locations, but remember that the Gateway must be hardwired for perma-nent installation.
7 98
Place extra Device ID stickers on your Lightcloud Device Table (see page 18) for future reference.
For each device, find the number from the panel board and write it down on the Device Table.
S T EP S E V EN S T EP N I N ES T EP EI G H T
G AT E WAY DE VICE IDs
1
2
3
NOTE: Use only RAB- authorized parts.
17Lightcloud Devices and Table
Lightcloud Device TableThe Device Table is essential for referencing during setup or for troubleshooting—don’t forget it! Two copies are provided: one to keep near your Gateway, and one for the building owner or facility manager to file.
PWR/ENGY: if a zone uses the Controller’s integrated power monitoring, place a checkmark.DIM: if a zone uses the Controller’s 0-10V dimming wires, place a checkmark here.
Lightcloud DevicesLightcloud devices that are mains hard-wired powered are designed to be installed on a junction box or similar enclosure, and must be installed by a qualified electrician. Refer to your device’s manual for installation considerations and best practices.
TIP: Use extra Device ID stickers on or near your devices or circuits for easier identification.
MO U NT IT H OW TO US E ITIN THE B OX
G ATEWAY ID:
Place Gateway ID sticker at the top.Mount device table to breaker box.DEVICE ID ZONE NAME PANEL/
CIRCUIT # PWR/ENGY DIM NOTES
18
Gateway ActivationWhen you power your Gateway and it shows sufficient cellular signal (solid yellow or green LED), call 1 (844) LIGHTCLOUD or 1 (844) 544-4825 to activate it and complete the rest of your site setup.
Network SetupTo add new devices to your Lightcloud network, call RAB at 1 (844) LIGHTCLOUD.
Software SetupLightcloud is cloud-based—no software to install or maintain, ever. Once you have a Lightcloud account, you can login to lightcloud.com at any time to configure and control your system.
Full ServiceNeed to change something about your system? No need to log in—RAB can do it for you! Call 1 (844) LIGHTCLOUD and our support specialists will get you where you want to be.
Setup
Setup
19
FCC Information:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.To comply with the FCC’s RF exposure limits for general population / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.CAUTION: Changes or modifications to this equipment not expressly approved by RAB Lighting may void the user’s authority to operate this equipment.
Welcome
Luminaire ControllerLCLC3/D10
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
®
HelloLightcloud is a wireless lighting control system. The Lightcloud Luminaire Controller is a remotely controlled switching and dimming device that can be installed into luminaires.
Product FeaturesWireless Control & ConfigurationSwitching up to 3A0-10V DimmingPower MonitoringPatent Pending
ContentsActuator Module, P/N 24586
Radio Module, P/N 24572
Wire Nuts
x 4 x 2
Instruction Manual
Gasket
1.5 in
3.7 in
1.3 in
2.0 in
2.0 in
1.0 in
What You NeedLightcloud GatewayA Lightcloud installation requires at least one Lightcloud Gateway to manage your devices.
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
Specifications & Ratings PART NUMBER LCLC3/D10
INPUT 120/277VAC, 50/60Hz
CURRENT DRAW <0.6W(Standby)–1W(Active)
LOAD SWITCHING CAPACITY LED, CFL, Tungsten 120/277VAC 500W; Magnetic 120VAC 264VA, 277VAC 500VA; Resistive/Inductive 120VAC 500W
OPERATING TEMPERATURE: -40ºC to +50ºC max temp
ACTUATOR MODULE OVERALL DIMENSIONS: 3.7” x 1.5” x 1.3”
RADIO MODULE OVERALL DIMENSIONS: 2” x 2” x 1”
WIRELESS RANGE Line-of-Sight: 700 feet Obstructions: 70 feet
INDOOR USE ONLY
DAMP LOCATION
Setup & Installation1
1a
Turn off power
OFF
OFF
WARNING
Find a Suitable LocationUse these guidelines when installing devices:• If there is a clear line of sight between a Luminaire Controller and
another Lightcloud device they can be placed up to 700 feet apart. • If a Luminaire Controller and another Lightcloud device are
separated by ordinary drywall construction, try to keep them within 70 ft. of each other.
• Brick, concrete and steel construction may require additional Lightcloud devices to go around the obstruction.
Lightcloud Gatewa y
<= 100 ft.
Add an additiona l Lightcloud Device to extend network range around corners BRIC K,
CO NCRE T E ORME TAL W AL LDR YW AL L
OR S IMIL ARDRYWALLOR SIMILAR
BRICK,CONCRETE, ORMETAL WALL
Setup & Installation (cont’d)
2
2a
Install the Luminaire ControllerFor luminaires pre-installed with the Luminaire Controller, skip to Step 3.
Fixture Installation with Actuator Module Inside
If the interior of your luminaire can accommodate the dimensions of the actuator module, install the actuator module inside the housing, and attach the radio module to the outside of the housing via a knockout.
INSIDE FIXTURE
GREY
GREY
RED
PURPLE
PURPLE
WH
ITE
WHITE
BLAC
K
BLACK
MODULAR CABLE
WHITE/ RED
120-277 VAC
Load or Fixture
24586 - ACTUATOR
GREY
GREY
RED
PURPLE
PURPLE
WHITE
INSIDE JUNCTION BOX
Load or Fixture BLACK
MODULAR CABLE
WHITE/ RED
WH
ITE
BLAC
K
120-277 VAC
24572 - RADIO
24586 - ACTUATOR
24572 - RADIO
Install Luminaire3
Install the luminaire with integrated Luminaire Controller as normal, allowing for any room to accommodate the external radio module of the LCLC3/D10.
Installation with Junction BoxIf the interior of your luminaire cannot accommodate the actuator module, the Luminaire Controller can be mounted into a junction box, with the radio module always outside any metal enclosure.
INSIDE FIXTURE
GREY
GREY
RED
PURPLE
PURPLE
WH
ITE
WHITE
BLAC
K
BLACK
MODULAR CABLE
WHITE/ RED
120-277 VAC
Load or Fixture
24586 - ACTUATOR
GREY
GREY
RED
PURPLE
PURPLE
WHITE
INSIDE JUNCTION BOX
Load or Fixture BLACK
MODULAR CABLE
WHITE/ RED
WH
ITE
BLAC
K
120-277 VAC
24572 - RADIO
24586 - ACTUATOR
24572 - RADIO
2b
Setup & Installation (cont’d)
Labeling your deviceWhen installing devices, it’s important to keep track of their Device IDs, installation locations, panel/circuit #s, dimming function, and any additional notes. To organize this information, use the Lightcloud Installer Application (A) or Device Table (B).
Install the LC Installer Application:LC Installer is available for iOS and Android.
Scan & Install Lightcloud Devices:Scan each device and assign to a room. It’s recommended that each device is scanned just before or just after being wired so no devices are missed. The more notes that are given, the easier it is to commission the system.
Send to RAB:Once all of the devices have been added and organized, submit the information for commissioning.
4
4a Lightcloud Installer Application
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
Scan Device Code
Device Info
SaveCancel
Device ID 0013A20040B62A4A
Location O�ce
Zone Name O�ce Lights
Dimmable
Power Monitoring
Enter Device Information Repeat for Additional Devices
Devices
Add DeviceSend to RAB
Office Light - ID 0013A20040B62A4AController
Office Light - ID 0013A20040B62A4BSensor
Office Light - ID 0013A20040B62A4CDimmer
Office Light - ID 0013A20040B62A4DDaylight
Office Light - ID 0013A20040B62A4ETouch
Send to RAB
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
DE VICE IDs
ZONE NA ME PANEL /CIRCUIT #
Setup & Installation (cont’d)
Two Lightcloud Device Tables are provided with each Gateway: one that you can attach to your panel and one to hand off to a building manager. Attach the Device Identifi cation stickers included with each device to a row, then write in additional information, such as Zone name, Panel/Circuit Number, and whether or not a Zoneuses dimming.
Power upTo add devices to your Lightcloud network, call RAB at1 (844) LIGHTCLOUD, or email us at [email protected]
5
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
Scan Device Code
Device Info
SaveCancel
Device ID 0013A20040B62A4A
Location O�ce
Zone Name O�ce Lights
Dimmable
Power Monitoring
Enter Device Information Repeat for Additional Devices
Devices
Add DeviceSend to RAB
Office Light - ID 0013A20040B62A4AController
Office Light - ID 0013A20040B62A4BSensor
Office Light - ID 0013A20040B62A4CDimmer
Office Light - ID 0013A20040B62A4DDaylight
Office Light - ID 0013A20040B62A4ETouch
Send to RAB
Device Scanner
Enter Manually
PLACE RECTANGLE TO FIT CODE ON LABEL
DE VICE IDs
ZONE NA ME PANEL /CIRCUIT #
4b Device Table
Confirm device connectivityConfirm Status Indicator is Solid Green (see details below)
DEVICE IDENTIFICATION BUTTON
POWER
• Press once to highlight this device in the Lightcloud Application
• Press twice to toggle circuit on and off
• Press twice and hold to set dim level
• Press and hold for 10 seconds to remove this device from a Lightcloud network
• Lit when device is on
SIGNAL INDICATORIlluminates when the device receives a message and indicates the strength of the signal by number of blinks:3 - Best signal2 - Acceptable signal1 - Unacceptable signalConsult the “Finding a Location” section for more information
STATUS INDICATORSolid GREEN when connected to your Lightcloud network. Blinking RED when not connected. The device will automatically continue trying to connect to a network in Setup Mode.
Commission your devices
6
Log on to www.lightcloud.com or call 1 (844) LIGHTCLOUD7
FunctionalityConfigurationAll configuration of Lightcloud products may be performed using the Lightcloud web Application, or by calling RAB.
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’RE HERE TO HELP:
Power MeasurementThe Lightcloud Luminaire Controller is capable of measuring the power usage of the attached luminaire. In order to utilize this func-tion, the neutral wire of the load must be connected to the white-red neutral wire. If the white-red neutral line cannot be used, it should be tied to the regular neutral wires (i.e. all neutral wires joined).
Power Loss DetectionIf mains power to the Controller is lost, the device will detect this and alert the Lightcloud Application.
Emergency DefaultIf communication is lost, the Controller may optionally fall back to a specific state, such as turning the attached luminaire on.[ Warning: Any wires not in use must be capped off or otherwise insulated. ]
FCC Information:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential envi-ronment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try and correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for
help.
To comply with the FCC’s RF exposure limits for general popula-tion / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications to this equipment not expressly approved by RAB Lighting may void the user’s authority to operate this equipment.
It’s powerful andflexible, yet easy to use and install. Learn more at lightcloud.com
1 (844) LIGHTCLOUD 1 (844) [email protected]
© RAB Lighting, Inc170 Ludlow Avenue Northvale, NJ 07647
Custom manufactured in China
Welcome
LCSENSE15/D10 (Ceiling Sensor)
Sensor
LCHBSENSE15/D10 (High Bay Sensor)
© RAB Lighting, Inc
170 Ludlow Avenue Northvale, NJ 07647
Custom manufactured in China
1 (844) LIGHTCLOUD1 (844) [email protected]
Lightcloud is a commercial wireless lighting control system & service. It’s powerful and flexible, yet easy to use and install. Learn more at lightcloud.com
1 (844) LIGHTCLOUD1 (844) 544-4825
WE’ RE HERE TO HELP:
Lightcloud is a wireless
lighting control service.
The Lightcloud Sensor
is a remotely configurable
passive infrared motion
sensor that can switch and
dim both hardwired circuits
and remote circuits using
Lightcloud Controllers.
Hello
Product FeaturesAdvanced PIR Sensing
Secure Cloud Control & Configuration
Retrofit-Friendly Local Control
Scheduling & Astronomical Clock
Power Monitoring
0-10V Dimming
Patent Pending
Temperature Monitoring Light Sensor
Contents
PART NUMBERLCSENSE15/D10 (Ceiling)LCHBSENSE15/D10 (High Bay)
INPUT120-277VAC, 50/60Hz, <1W (Standby) - 2W (Active)
MAXIMUM SWITCHED LOAD RATINGSElectronic Ballast: 277VAC, 3300WMagnetic Ballast: 277VAC, 1200W / 120VAC, 800WTungsten: 220VAC, 3000WDimming: 0-10V (Class2)
OPERATING TEMPERATURE-20ºC to 40ºC
Specifications
OPERATING HUMIDITY10% RH to 95% RHNon-Condensing
OVERALL DIMENSIONS4.91” Diameter, 1.61” Height
WIRELESS RANGE Line-of-Sight: 1000 feet
Obstructions: 100 feet
Warranty is active as long as service plan is active.
Indoor Damp LocationLightcloud Ceiling Sensoror High Bay Sensor
Instruction ManualWire Nuts
x 4
x 2
What You NeedLightcloud Gateway A Lightcloud installation requiresat least one Lightcloud Gateway tomanage your devices.
AccessoriesFor use with High Bay Sensor Only
Lens Cover for 180° Coverage (included)
Arm (optional, includes2 screws and 1 locknut)
Height Adjuster(optional, must use inconjunction with Arm)
Setup & Installation1 Find a suitable location
Use these guidelines when installing devices:
• If there is a clear line of sight between two Lightcloud devices, they can be placed up to 1000 feet apart.
• If the two devices are separated by ordinary drywall construction, try to keep them within 100 feet of each other.
• Brick, concrete and steel construction may require additional Lightcloud devices to go around the obstruction.
Lightcloud Gateway
<= 100 ft.
Add an additional Lightcloud Device to extend network range around corners B R I C K ,
CO N C R E T E O R
M E TA L WA L LD R Y WA L L O R S I M I L A R
INSTALL AT A JUNCTION BOX (INDOOR/OUTDOOR)
The Sensor can control other Lightcloud devices, wirelessly. If you don’t need to hard-wire a switched circuit to the Sensor, no problem—just tie the white/red wire to neutral and cap o� any unused wires.
2 Install your Lightcloud Sensor
Sensor attached attached to wired
junction box
SWITCHED NEUTRALThe “Switched Neutral” white with red stripe wire is the neutral line for the load being switched. This enables power measurement. See the Power Measurement section under “Functionality” for more information.
BLACK
WHITE/RED
0-10V
DIMMING
Panel
Load
BLA
CK
/ H
OT
WH
ITE
/ N
EUTR
AL
WHITE
BLACK
RED
WHITE
PURPLE
GRAY
PURP
LE
GR
AY
Setup & Installation (cont’d)
! This product should only be installed by a quali�ed electrician and in compliance with local and national electrical codes.
3 Installing Accessories (High Bay only)
Arm:
mount sensor to
�xture using ½” NPS
threaded nipple
Height Adjuster:
adjust height by loosening set screw, moving sensor up or down along
extruded tube, then tightening set screw. Ensure sensor lens is not
blocked by any part of the �xture.
ARM
½” NPS THREADSSENSOR
LOCKNUT
SET SCREW
Extruded Tube
4 Wiring
DE VICE IDs
5 Labeling your device
For setup and maintenance, we provide two Lightcloud Device Tables withthe Gateway: one that you can attach to your panel and one to hand o� toa building manager. Attach the Device Identification stickers included witheach device to a row, then write in additional information, such as Zonename, Panel/Circuit Number, and whether or not a zone uses dimming.
ZONE NA MEPANEL /CIRCUIT #
Setup & Installation (cont’d)
6
7
Power up
Confirm device connectivityConfirm status indicator LED (see step 8) is solid green. If it is not, makesure your device is within range of another Lightcloud AC-powered device.
To add new devices to your Lightcloud network, contact RAB:
1 (844) LIGHTCLOUDor 1 (844) 544-4825
WE’ RE HERE TO HELP:
Setup & Installation (cont’d)
8 Place coverSecure cover onto sensor by pushing up and twisting to the right (clockwise).
STATUSINDICATOR
9 Commission & Con�gure Your DevicesAll Lightcloud products can be commissioned and configured by:
• Logging on to lightcloud.com
• Calling RAB at 1 (844) LIGHTCLOUD
• Emailing us at [email protected]
Functionality
OverviewSTATUS INDICATOR
POWER INDICATOR
DEVICE BUTTON
MOTION INDICATOR
LIGHT SENSOR
SENSOR
SIGNAL INDICATOR
STATUS INDICATOR:
• Solid GREEN when connected to your Lightcloud network• Blinking RED when not connected to a Lightcloud network. The device will automatically continue trying to connect to a network that is in Setup Mode.
POWER INDICATOR:
Illuminated when powered. Blinking when indicated from the Lightcloud application.
SIGNAL INDICATOR:
After the Device Button has been pressed, this indicator illuminates when the device receives a message and indicates the strength of the signal. 3 - Best Signal2 - Acceptable Signal1 - Unacceptable SignalConsult the “Finding a Location” section for more information.
DEVICE BUTTON:
• Press once to highlight this device in the Lightcloud Application (pressing once also enables display of the Signal Indicators)• Press twice to toggle circuit on and o�• Press twice and hold to set dim level• Press and hold for 10 seconds to remove this device from a Lightcloud network
MOTION INDICATOR:
Illuminates when motion is detected
SENSOR:
Passive-infrared motion sensor
Features
OCCUPANCY & VACANCY SENSING:
The Lightcloud Sensor can operate in either Occupancy or Vacancy Sensor modes, selectable via the Lightcloud application. In Occupancy mode, the attached circuit will be switched on when motion is detected, and o� (or dimmed) when the timeout expires. In Vacancy mode, the attached circuit will be turned o� when the motion timeout expires, but will only be turned on via the Lightcloud application, Lightcloud Wall Switch, or similar. Motion detection and timeout can still be used via Lightcloud Automations to control other devices.
CONTROLLER MODE:
In Controller Mode, the attached circuit is controllable as an independent zone in the Lightcloud application. Motion detection and timeout can still be used via Lightcloud Automations to control other devices.
RANGE TEST MODE:
When Range Test Mode is activated via the Lightcloud application, the timeout period is shortened so that you can test di�erent sensitivities quickly. All indicators will go o� except for the Motion Indicator. When satis�ed, turn o� Range Test Mode to continue normal operation.
Functionality (cont’d)
Features: Passive Infrared Motion Detection
SIDE VIEW
SIDE VIEW
TOP VIEW TOP VIEW
15’ 7.5’ 7.5’ 15’
30’
9’
0’
0’
7.5’
7.5’
15’
15’
CEILING SENSOR
20’ 14’ 14’ 20’
40’
30’
0’
0’
14’
14’
20’
20’
HIGH BAY SENSOR
POWER LOSS DETECTION:
If power to the Sensor is lost, the device will detect this and alert the Lightcloud application.
EMERGENCY DEFAULT:
If communication is lost, the Sensor may optionally fall back to a speci�c state, such as turning the attached circuit on. This may be con�gured via the Lightcloud application or by calling RAB.
0-10V DIMMING:
0-10V is a common method of low-voltage control of dimmable drivers and ballasts. Purple: 0-10V positive | Gray: 0-10V commonNote: The National Electrical Code requires that low-voltage wiring used in the same enclosure as high voltage wiring have an equal or better insulation rating. You mayneed to complete your low-voltage wiring in another enclosure or use a partition.
DEVICE IDENTIFICATION:
For help with installation, there are two ways to identify this device:• Pressing the Device Button on the actual product will produce a message in the Lightcloud application indicating which device you are working with.• Pressing the “Indicate” button in the Lightcloud application will cause the device’s Status Indicator to blink green. This will also switch the device’s relay on and o� repeatedly, allowing you to quickly identify which circuit it is.
POWER MEASUREMENT:
The Lightcloud Sensor is capable of measuring the power usage of the attached circuit. In order to utilize this function, the neutral wire of the load must be connected to the white-red switched neutral wire. If this wire is not used, it should be tied to the regular neutral wire (i.e. all neutral wires joined).
FCC Information:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, ofthe FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment.This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o� and on, the user is encouraged to try and correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit di�erent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
To comply with the FCC's RF exposure limits for general population / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Changes or modi�cations to this equipment not expressly approved by RAB Lighting may void the user’s authority to operate this equipment.
Functionality (cont’d)
Features