8/9/2019 Manual Clima
1/48
87-11
Manual A/C
Heating and A/C components in passengercompartment, servicing
CAUTION!
Before beginning repairs on the electrical system:
Note:
System components identified with an * must only be serviced or replaced after discharging refrigerant system.
Use Kent Moore ACR4 or equivalent.
Obtain the anti-theft radio security code.
Switch the ignition off.
Disconnect the battery Ground (GND) strap. After reconnecting battery, re-code and check operation of anti-theft radio. Also check operation of clock and power windows according to Repair Manual and/or Owner's Manual.
8/9/2019 Manual Clima
2/48
87-12
Repair Manual, Body Interior, Repair Group 70.
1 - Clip
Lift out with screwdriver.
2 - Dust and pollen filter
Vehicles 10.00 , replacing Page 87-41 .
3 - Air intake housing
4 - Defroster air outlet
Removing and installing
5 - Side window air outlet
Removing Fig. 1
8/9/2019 Manual Clima
3/48
87-13
6 - Heating and A/C controls
With:
A/C switch -E35-
Fresh air blower switch -E9-
Switch for fresh air blower and recirculated air -E184-
Removing and installing Page 87-27
Assembly Page 87-30
7 - Air outlets
Center and side air outlets, removing (early prod.)Fig. 2
Center air outlet, removing (later prod.) removingFig. 3
Side air outlets, removing (later prod.) Fig. 4
8 - Instrument panel cross member
Always follow installation instructions for bolt Fig.7
8/9/2019 Manual Clima
4/48
87-14
Repair Manual, Body Interior, Repair Group 70
Repair Manual, Body Interior, Repair Group 68
9 - Defroster duct
Replacing:
- Remove instrument panel
10 - Servo motor for fresh/recirculating air door -V154-
Removing and installing Page 87-26
11 - Ambient temperature switch -F38-
Switches off A/C clutch -N25- at low ambienttemperatures
Switching point: 5 C (41.5 F)
Replacing:
- Remove glove box
- Reach behind heating and A/C unit from belowand pull out switch.
8/9/2019 Manual Clima
5/48
87-15
CAUTION!
Area around dust and pollen filter and air intake housing must be free from debris, leaves etc. before reaching into housing. Debris entering heating and A/C unit will block evaporator water drain and cause subsequent (water) damage.
Note:
If unable to access and remove gasket as described,proceed as follows:
Repair Manual, Body Interior, Repair Group 70
12 - Gasket
Replace if damaged
Replacing:
- Remove ambient temperature switch -F38-
- Remove dust and pollen filter
- Set fresh air/recirculation flap in "fresh air" position
- Reach down into air intake housing and pull outgasket
- Remove instrument panel
8/9/2019 Manual Clima
6/48
- Loosen cross member - 10 - .
Always follow installation instructions for bolt Fig.7
8/9/2019 Manual Clima
7/48
87-16
13 - Evaporator water drain guide
Removing and installing Page 87-25
14 - Heating and A/C unit*
Contains:
Heater core
Evaporator
Removing/assembly Page 87-164 .
15 - Fresh air blower -V2-
Removing and installing Fig. 6
16 - Fresh air blower series resistance with fuse -N24-
Replacing Fig. 5
17 - Center air outlet duct
18 - Control panel trim
Unclip using screwdriver
19 - Center trim
8/9/2019 Manual Clima
8/48
87-17
20 - Heating and A/C cables
Installing Page 87-32
21 - Heater core*
Always use new coolant after replacement
22 - Left rear duct
23 - Lower duct
24 - Upper duct
25 - Footwell air outlet
26 - Instrument panel cross member and left sidemember securing bolt
Always follow installation instruction for bolt Fig.7
8/9/2019 Manual Clima
9/48
87-18
27 - Relay
Coolant Fan Control (FC) Relay -J26-
Control number 214
First Speed Coolant Fan Control (FC) relay -J279-
Vehicles 10.00: Control number 214
Vehicles 10.00 : Control number 373
Second Speed Coolant Fan Control (FC) Relay -J280-
Vehicles 10.00: Control number 213
Vehicles 10.00 : Control number 370
Component locations Electrical Wiring Diagrams,Troubleshooting and Component Locations.
28 - A/C cut-off control module -J314-
Control number 384
Component location Electrical Wiring Diagrams,Troubleshooting and Component Locations.
8/9/2019 Manual Clima
10/48
87-19
Fig. 1 Side window air outlet, removing
- Carefully pull out using needle-nose pliers.
Fig. 2 Center and side air outlets, removing (early prod.) - With flashlight, locate the two retaining tabs inside housing, lift tabs with two
small screwdrivers and carefully pull outlet from instrument panel.
8/9/2019 Manual Clima
11/48
87-20
Note:
Fig. 3 Center air outlet, removing (later production)
- Insert fingers of both hands into lower row of grille -A- and push center vent -1-down suing force until locking lugs -B- are released from their mounts.
Sit between front seats to apply the force required.
If outer locking lugs -B- will not release, grip at this point and push center vent down while simultaneously pulling out slightly.
- Grip center vent -1- at point -C- which has been raised up slightly frominstrument panel opening by action of pushing down.
- Push center vent in direction -D- to release locking lugs and pull it outwardslightly.
8/9/2019 Manual Clima
12/48
87-21
- Disconnect electrical connectors -2- from center vent before removing indirection of -arrow-.
Note:
Removal of both sides is identical.
Fig. 4 Side air outlet, removing (later prod.)
- Unclip and remove instrument panel side cover -1- using screwdriver.
8/9/2019 Manual Clima
13/48
87-22
- Guide a flat screwdriver between vent and seal alternately into side openings -A-and -B-.
- Pry vent -2- in direction -C- alternately through these openings.
7
- Disconnect electrical connector -3- when removing vent -2- in direction -C-.
8/9/2019 Manual Clima
14/48
87-23
Repair Manual, Body Interior, Repair Group 68.
Fig. 5 Fresh air blower series resistance with fuse -N24- , replacing
- Remove glove box.
- Disconnect electrical connector and remove bolt -arrow-.
- Seal surface between series resistance -1- and air duct before installing withAMV 176 000 05 (or equivalent).
Repair Manual, Body Interior, Repair Group 68.
Fig. 6 Fresh air blower -V2-, removing and installing - Remove glove box
- Disconnect electrical connector -1-.
- Remove three screws -arrows- and remove fresh air blower -2- downwards.
8/9/2019 Manual Clima
15/48
87-24
To avoid damage to instrument panel wiring harness -2-, ensure that the protectivecap -1- is installed on the securing bolt for upper instrument panel cross member -4- at left side member -3-.
Fig. 7 Instrument panel cross member and left side member securing bolt,installation note:
8/9/2019 Manual Clima
16/48
87-25
Evaporator water drain guide, removing andinstalling
Removing
- Remove instrument panel
Repair Manual, Body Interior, Repair Group 70.
- Release instrument panel cross member frombulkhead Page 87-13 .
For the next step, an assistant must lift and holdthe heating and A/Cunit.
Installing
When installing, ensure water drain valve -3- sealing lip completely encloses theguide -2-. If necessary, lubricate to aid installation.
Water drain valve, checking Page 87-40 , Fig. 1
- Remove nuts -1- (2.5 Nm / 23 in lb) and remove guide -2- from bulkhead.
8/9/2019 Manual Clima
17/48
8/9/2019 Manual Clima
18/48
87-27
Heating and A/C controls, removing andinstalling
Removing
- Carefully remove trim panel by depressinglocating lugs -arrows-with a covered screwdriver.Do not damage instrument panel.
- Remove instrument panel screws -arrows-.
- Remove center trim panel Page 87-16 .
- Pull controls with cables attached from instrument panel.
- Release cables on controls.
- Disconnect electrical connector.
8/9/2019 Manual Clima
19/48
87-28
Installing
Notes:
Cable sleeve ends are color coded.
Check cables before installing and replace binding or damaged cables.
All air flaps must audibly move onto end stops when turning controls.
- Mount eyelet on end of cable -1- onto control - arrow 2-.
Footwell/defrost flap cable sleeve marking: White
- Press footwell/defrost or central flap cable -1- into mount -2- until it engages.
8/9/2019 Manual Clima
20/48
Central flap cable sleeve marking: Black
8/9/2019 Manual Clima
21/48
87-29
Temperature flap cable sleeve marking: Red
- Insert temperature flap cable -1- into mount opening -arrow B-.
- Turn -arrow A- temperature flap cable -1- until it engages into air distributorhousing -2-.
8/9/2019 Manual Clima
22/48
87-30
Heating and A/C controls, assembly
1 - Heating and A/C controls
With:
A/C switch -E35-
Fresh air blower switch -E9-
Switch for fresh air blower and recirculated air -E184-
Removing and installing Page 87-27
2 - Illumination filter
3 - Trim panel
4 - Fresh air control lever light -L16-
12V, 1.2W
Removing:
- Un-clip trim panel - 7 - and rotary control - 5 -.
- Remove bulb (if necessary, slide a short piece fuel
hose over bulb and pull out).
5 - Rotary control
For blower speed
To remove: Use pliers with suitable plastic or rubber
8/9/2019 Manual Clima
23/48
protection on jaws
8/9/2019 Manual Clima
24/48
87-31
6 - Rotary control
For air distribution To remove: Use pliers with suitable plastic or rubberprotection on jaws
7 - Trim panel
8 - Rotary control
For interior temperature
To remove: Use pliers with suitable plastic or rubberprotection on jaws
8/9/2019 Manual Clima
25/48
87-32
Heating and A/C cables, installing
Notes: Cable sleeve ends are color coded.
Check cables before installing and replace binding or damaged cables.
All air flaps must audibly move onto end stops when turning controls.
1 - Central flap cable
From air distribution rotary control to central flap
Cable sleeve marking: Black
Removing and installing Page 87-34
8/9/2019 Manual Clima
26/48
87-33
Repair Manual, Body Interior, Repair Group 68
2 - Footwell/defrost flap cable
From air distribution rotary control to footwell/defrostflap
Cable sleeve marking: White
Replacing:
- Remove controls for heating and A/C systemPage 87-27
- Remove driver side shelf
- Unclip cable at heating and A/C unit.
- When installing, attach cable to heating and A/Cunit first.
3 - Heating and A/C controls
Removing Page 87-27
4 - Temperature flap cable
From temperature rotary control to temperature flap
Cable sleeve marking: Red
Removing and installing Page 87-34
8/9/2019 Manual Clima
27/48
87-34
Temperature and central flap cables,removing and installing
Notes:
Cable sleeve ends are color coded.
When installing secure cable to heating and A/C unit first.
Check cables before installing and replace
binding or damaged cables.
Removing
- Remove heating and A/C controls Page 87-27
- Remove instrument panel
Repair Manual, Body Interior, Repair Group 70
- Remove footwell air outlet Page 87-17 .
8/9/2019 Manual Clima
28/48
- Disconnect cable for central flap or temperature
flap on heating and A/C unit.
8/9/2019 Manual Clima
29/48
87-35
Installing
Illustration shows right-hand drive version.
1- Central flap cable, sleeve marking: Black
2- Temperature flap cable, sleeve marking: Red
3- When attaching inner cable note: Do not press end of wire (arrow) against lever.
8/9/2019 Manual Clima
30/48
87-36
Heating and A/C components in enginecompartment, servicing
CAUTION!
Before beginning repairs on the electrical system:
Notes:
Obtain the anti-theft radio security code.
Switch the ignition off.
Disconnect the battery Ground (GND) strap.
After reconnecting battery, re-code and check operation of anti-theft radio. Also check operation of clock and power windows according to Repair Manual and/or Owner's Manual.
System components identified with an * must only be serviced or replaced after discharging refrigerant system.Use Kent Moore ACR4 or equivalent.
Illustration shows vehicle with engine code AHA.
8/9/2019 Manual Clima
31/48
87-37
1 - Accumulator*
2 - Refrigerant hose*
Between evaporator and accumulator
3 - Refrigerant hose*
Between evaporator and condenser
4 - Low pressure service valve*
5 - High pressure service valve*
6 - Dust and pollen filter
Vehicles 10.00 , replacing Page 87-41
Ambient temperature switch -F38- located belowdust and pollen filter in lower air intake housing.
7 - Evaporator*
In heating and A/C unit.
8/9/2019 Manual Clima
32/48
87-38
8 - Evaporator water drain valve
Checking Fig. 1 .
9 - Pressure relief valve*
Zexel compressor illustrated
Checking, Zexel compressor Page 87-159
Checking, Denso compressor Page 87-160
10 - Compressor*
11 - A/C clutch -N25-
Servicing: Zexel Page 87-43
Servicing: Denso Page 87-49
12 - Condenser*
8/9/2019 Manual Clima
33/48
87-39
13 - A/C pressure switch -F129-
-
Tightening torque 8 Nm (71 in lb)
- Replace O-ring (note Part No.).
Function:
Switches coolant fan -V7- to next highest speedwhen pressure increases in refrigerant circuit.
Switches off A/C clutch -N25- when refrigerantpressure is excessive (e.g.: insufficient enginecooling).
Switches off A/C clutch -N25- when refrigerantpressure is too low (e.g.: refrigerant loss).
Checking Page 87-154
Replacing, 10.00 Page 87-156, Fig. 4 .
Replacing, 10.00 Page 87-157, Fig. 5 .
14 - Refrigerant hose*
Between compressor and condensor
15 - Refrigerant hose*
Between compressor and accumulator.
8/9/2019 Manual Clima
34/48
87-40
Check drain valve as follows:
Note:
Catalytic converter heat shield from 10.00 differs from illustration.
Check valve as follows to ensure proper function:
Fig. 1 Evaporator water drain valve, checking
- Remove nuts -arrows- on right catalytic converter heat shield -1-.
- Remove catalytic converter heat shield.
The valve must not be stuck together.
The opening in the sealing cap of the valve must point downwards.
The right catalytic converter heat shield plate must not be deformed ordamaged in the area of the valve.
- Remove valve -1- from bulkhead -2-.
The valve sealing lip -1- must cover the water drain guide outlet completelyPage 87-25 .
8/9/2019 Manual Clima
35/48
87-41
Dust and pollen filter 10.00 , removingand installing
Removing
- Lift front hood. Remove air intake plenumcover.
Installing
- Unclip spring -1-. Remove dust and pollen filter upwards from housing.
- Installation in reverse order of removal.
Filter housing, assembly
1 - Filter housing
2 - Dust and pollen filter
3 - Nut (2Nm)
8/9/2019 Manual Clima
36/48
87-42
Ventilation system, checking
Notes:
Passenger compartment air is vented to the outside trough openings in the luggage compartment trim.
In order for the ventilation system to work properly, these openings must not be blocked.
Vent frames are located in both rear quarter panels, behind the bumper cover.
Checking
- Remove rear bumper cover
Repair Manual, Body Exterior, Repair Group 63
- Sealing lips -1- in vent frame -2- must move and close freely.
8/9/2019 Manual Clima
37/48
87-43
A/C clutch -N25-, servicing (Zexel)
Special tools, workshop equipment, test and measuringappliances and auxiliary items required
Not illustrated:
3212 Two hole pin wrench
VAG 1719 A/C Clutch set
VAG 1719/1 Adapter
VAG 1719/2 Adapter
Torque wrench (5 - 50 Nm)
Locally available two-arm puller (e.g. Kukko 20-10) withfixtures for a depth of 100 mm.
Feeler gauge
8/9/2019 Manual Clima
38/48
87-44
Notes:
Refrigerant circuit does not need to be opened to service
A/C clutch. If unable to service A/C clutch on compressor installed in vehicle, discharge refrigerant Page 87-173 and remove compressor from compressor bracket.
1 - Hex head combination bolt
15 Nm (11 ft lb)
Removing and installing Fig. 1
2 - Clutch plate
Removing Fig. 2
Checking clutch plate gap Fig. 6
3 - 45Shims
Used to adjust gap between clutch plate and pulley
Gap: 0.3 - 0.6 mm (0.011 - 0.023 in)
6 - Circlip
Always replace - Install correctly: thick side faces compressor
Ensure correct seating in groove
8/9/2019 Manual Clima
39/48
87-45
Note:
A thermo-fuse is incorporated into the clutch coil. Current to the clutch coil is interrupted in the event of compressor overheating (e.g. a binding compressor).
7 - Clutch pulley
Removing Fig. 3
Installing Fig. 4
8 - Circlip
Always replace
- Install correctly: Flat side faces compressor
Ensure correct seating in groove
9 - Clutch coil
Installing Fig. 5
10 - Felt ring
Always replace
11 - Bolt
12 - Compressor
Manufacturer: Zexel
8/9/2019 Manual Clima
40/48
87-46
When removing and installing bolt, counter-hold with 2 hole pin wrench -A- (3212 orequivalent) with pin diameter: 4 mm.
Fig. 1 Combination bolt for clutch plate, removing and installing
- Remove bolt.
Tightening torque: 15 Nm (11 ft lb)
When removing, counter-hold with 2 hole pin wrench -A- (3212 or equivalent).
Fig. 2 Clutch plate, removing
- Mount VAG 1719 and turn in center bolt to extract clutch plate.
8/9/2019 Manual Clima
41/48
87-47
Fig. 3 Clutch pulley, removing
- Remove felt ring.
- Fit adapter VAG 1719/1 (or equivalent).
- Fit locally available 2 arm puller -B- on shoulder -A- and extract pulley.
Fig. 4 Clutch pulley, installing
- Drive on belt pulley with plastic head hammer and VAG 1719/2 (or equivalent).
8/9/2019 Manual Clima
42/48
87-48
Fig. 5 Clutch coil, installing
- Install coil on compressor.
- Position pin -A- in recess.
Notes:
Fig. 6 Clutch plate gap, checking
- Check gap with feeler gauge.
Gap: 0.3 - 0.6 mm (0.011 - 0.023 in)
Gap must be within tolerance around entire circumference.
If gap is outside tolerance range, remove clutch plate and adjust gap by adding or removing shims Page 87-44 .
8/9/2019 Manual Clima
43/48
87-49
A/C clutch -N25-, servicing (Denso)
Special tools, workshop equipment, test and measuringappliances and auxiliary items required
Not illustrated:
Torque wrench (5 - 50 Nm)
Locally available two-arm puller (e.g. Kukko 20-10) withfixtures for a depth of 100 mm.
Locally available strap wrench
Depth gauge
8/9/2019 Manual Clima
44/48
87-50
Notes:
Refrigerant circuit does not need to be opened to service
the A/C clutch.
If unable to service A/C clutch on compressor installed in vehicle, discharge refrigerant Page 87-173 and remove compressor from compressor bracket.
1 - Hex head combination bolt
15 Nm (11 ft lb)
Removing and installing Fig. 1
2 - Clutch plate
Removing Fig. 2
Checking clutch plate gap Fig. 4
3 - Shims
Used to adjust gap between clutch plate and pulley
Gap: 0.4 - 0.6 mm (0.015 - 0.023 in)
4 - Circlip
Always replace
- Install correctly: Thick side faces compressor.
Ensure correct seating in groove.
8/9/2019 Manual Clima
45/48
87-51
Note:
A thermo-fuse is incorporated into the clutch coil. Current to the clutch coil is interrupted in the event of compressor overheating (e.g. a binding compressor).
5 - Clutch pulley
- Remove with locally available 2 or 3 arm puller.
Ensure puller is seated correctly to prevent damage topulley.
6 - Circlip
Always replace
- Install correctly: Flat side faces compressor.
Ensure correct seating in groove.
7 - Clutch coil
Installing Fig. 3
8 - Screw
9 - Compressor
Manufacturer: Denso
8/9/2019 Manual Clima
46/48
87-52
When removing and installing bolt, counter-hold with locally available strap wrench-A-.
Fig. 1 Combination bolt for clutch plate, removing and installing
- Remove bolt.
Tightening torque: 15 Nm (11 ft lb)
Use locally available 2 or 3 arm puller if plate is securely seated (difficult toremove).
Fig. 2 Clutch plate, removing
- Pry off clutch plate carefully with two large screwdrivers.
8/9/2019 Manual Clima
47/48
87-53
Fig. 3 Clutch coil, installing
- Install coil on compressor.
- Locate locking pin -A- in recess -B-.
Note:
Repair Manual, Body Exterior, Repair Group 50.
Determine "Dimension 1"
Fig. 4 Clutch plate gap, checking
Gap: 0.4 - 0.6 mm (0.015 - 0.023 in)
In order to check gap with compressor installed in vehicle:
- Bring front end assembly (lock carrier) into service position.
- Using depth gauge -C-, measure gap between top of clutch plate and belt pulleyat three equally spaced locations (measurement must not deviate).
87 54
8/9/2019 Manual Clima
48/48
87-54
Determine "Dimension 2"
The allowable gap (0.4 - 0.6 mm / 0.015 - 0.023 in) is the difference between"Dimension 1" and "Dimension 2".
Notes:
- If compressor is installed in vehicle, disconnect compressor electrical connector -A- from vehicle wiring harness.
- Using a jumper wire, energize clutch coil by applying 12V to connector -A-(battery terminal B+). If compressor is removed from vehicle, compressor -B-must be grounded.
- With clutch energized, measure gap between belt pulley and clutch plate withdepth gauge -C-:
Gap must be within tolerance around entire circumference.
If gap is outside the permitted tolerance range, remove clutch plate and adjust gap by adding or removing shims Page 87-50 .