PFPF PNFPNFA330
BEFORE START…
…ENGINE START…
…AFTER START
A330 - Version 03
PFPF PNFPNFA3301.a. BEFORE START
LOADSHEET……………..………………….CHECK
COCKPIT DOOR………..………………….CLOSED
Confirm any takeoff weight limitation.
Ask for external power disconnection
TAKEOFF DATA.........…………..…ENTER/REVISE
SEAT BELTS…………………………………ADJUST
MCDU………………………………………...PERF TO
ORDER….”BEFORE START C/L down to the line”
TAKEOFF DATA.........……………………XCHECK
SEAT BELTS……………………………….ADJUST
MCDU………………………………………….F-PLN
EXT PWR………………………………………..OFF
BEFORE START down to the line..…PERFORM
ANNOUNCE………………..”BEFORE START C/Ldown to the line COMPLETED”
PFPF PNFPNFA3301.b. BEFORE START
CAUTION ! DO NOT PERFORM the pushback if NW STRG DISC notdisplayed on the ECAM MEMO to avoid damages to the nose landing gear.
The BRAKE ACCU PRESSmust be in the green band When PARKING BRAKE is ON:
brake pressure is shownPARK BRK MEMO is displayed
NW STRG DISC MEMO........……………..CHECK
WINDOWS and DOORS…….…CHECK CLOSED
THR LEVERS……………………….……….…IDLE
PARKING BRAKE ACCU PRESS…….…CHECK
PARKING BRAKE………………………….……ON
ORDER….”BEFORE START C/L below the line”
GROUND CREW COMMUNICATION…ESTABLISH
PUSHBACK/START CLEARANCE…….OBTAIN
WINDOWS………………………………….CHECK
BEACON…………………………………………ON
BEFORE START C/L below the line…PERFORMANNOUNCE………………..”BEFORE START C/L
COMPLETE”
PFPF PNFPNFA3302. AUTOMATIC ENGINE START SEQUENCE
ENG START SEL.........………………….IGN/START
BLEED PRESSURE…………………………CHECK
ANNOUNCE……………....”STARTING ENGINE 1”
MASTER SW 1…………………………………….ONSTART VALVE OPENSN2 INCREASES (N3 for RR)IGNITERFUEL FLOWEGTN1OIL PRESSSTART VALVE CLOSE
• 50% N2 (GE)• Between 43% and 48% N2 (PW)• 50% N3 (RR)
ENG IDLE PARAMETERS……..CHECK NORMAL
ANNOUNCE……………...”STARTING ENGINE 2”REPEAT START SEQUENCE FOR ENG 2………..
..CHECK
Check BLEED PRESSURE on ECAM page. ECAM ENGINE page
RRGE PW
Start ENG 2 ONCE AVAIL is displayed
for ENG 1 XX.X
PFPF PNFPNFA3303.a. AFTER START
ENG START SEL…………………….……NORM
APU BLEED………………………………….OFF
ECAM STATUS…………………….………CHECK
ECAM DOOR PAGE…...………………….CHECK
ANNOUNCE….……”CLEAR TO DISCONNECT”
1. GND SPLRS…………………………………ARM
2. RUD TRIM…………………………………RESET
3. FLAPS…………………………………………SET
4. PITCH TRIM…………………………………..SET
ENG ANTI ICE…………………………AS RQRD
WING ANTI ICE………………………..AS RQRD
6. APU MASTER SW……………………………OFF
End of START sequence : Signal for PNF actions
Pedestal
OverheadPanel
5.
5
6
4
1
2
3
ENGINE WHEEL
ENG START SELback to NORM
ECAM
PFPF PNFPNFA3303.b. AFTER START
To stabilize engine hot section temperature:
If icing conditions :
3 min (GE) / 5 min (PW & RR) / 3 min (RR ifengines have been stopped for 1.5 hr or less)
minimum at or near IDLE
Enginestarted
High power
t
GE : RR : PW :
engines started
Observe the ECAM MEMO:
NWS TOWING FAULT LT extinguished…CHECK
AFTER START C/L
t (min.)0 2
PFPF PNFPNFA3302. AUTOMATIC ENGINE START SEQUENCE
ENG START SEL.........………………….IGN/START
BLEED PRESSURE…………………………CHECK
ANNOUNCE……………....”STARTING ENGINE 1”
MASTER SW 1…………………………………….ONSTART VALVE OPENSN2 INCREASES (N3 for RR)IGNITERFUEL FLOWEGTN1OIL PRESSSTART VALVE CLOSE
• 50% N2 (GE)• Between 43% and 48% N2 (PW)• 50% N3 (RR)
ENG IDLE PARAMETERS……..CHECK NORMAL
ANNOUNCE……………...”STARTING ENGINE 2”REPEAT START SEQUENCE FOR ENG 2………..
..CHECK
Check BLEED PRESSURE on ECAM page. ECAM ENGINE page
Start ENG 2 ONCE AVAIL is displayed
for ENG 1
RRGE PW
ENG 1 is started first because it powers the blue hydraulic system, which pressurizes the parking
brake.
DO NOT SET the MASTER switch ON before all amber crosses and messages have disappeared on
engine parameters (upper ECAM display).
ENG 1 is started first because it powers the blue hydraulic system, which pressurizes the parking
brake.
DO NOT SET the MASTER switch ON before all amber crosses and messages have disappeared on
engine parameters (upper ECAM display).
Select “IGNSTART”
Set ENG masterswitch to ONWait 3 sec.
PFPF PNFPNFA3302. AUTOMATIC ENGINE START SEQUENCE
ENG START SEL.........………………….IGN/START
BLEED PRESSURE…………………………CHECK
ANNOUNCE……………....”STARTING ENGINE 1”
MASTER SW 1…………………………………….ONSTART VALVE OPENSN2 INCREASES (N3 for RR)IGNITERFUEL FLOWEGTN1OIL PRESSSTART VALVE CLOSE
• 50% N2 (GE)• Between 43% and 48% N2 (PW)• 50% N3 (RR)
ENG IDLE PARAMETERS……..CHECK NORMAL
ANNOUNCE……………...”STARTING ENGINE 2”REPEAT START SEQUENCE FOR ENG 2………..
..CHECK
Check BLEED PRESSURE on ECAM page. ECAM ENGINE page
Start ENG 2 ONCE AVAIL is displayed
for ENG 1
RRGE PW
DO NOT SET the MASTER switch ON before EGT amber crosses and messages have disappeared on
engine parameters (upper ECAM display).
ENG 1 is started first because it powers the blue hydraulic system, which pressurizes the parking
brake.
DO NOT SET the MASTER switch ON before EGT amber crosses and messages have disappeared on
engine parameters (upper ECAM display).
ENG 1 is started first because it powers the blue hydraulic system, which pressurizes the parking
brake.
Starting a hot engine
(1st start: EGT>100°C2nd start: EGT>150°C)
EEC performs a dry crank toreduce engine temperature
PFPF PNFPNFA3302. AUTOMATIC ENGINE START SEQUENCE
ENG START SEL.........………………….IGN/START
BLEED PRESSURE…………………………CHECK
ANNOUNCE……………....”STARTING ENGINE 1”
MASTER SW 1…………………………………….ONSTART VALVE OPENSN2 INCREASES (N3 for RR)IGNITERFUEL FLOWEGTN1OIL PRESSSTART VALVE CLOSE
• 50% N2 (GE)• Between 43% and 48% N2 (PW)• 50% N3 (RR)
ENG IDLE PARAMETERS……..CHECK NORMAL
ANNOUNCE……………...”STARTING ENGINE 2”REPEAT START SEQUENCE FOR ENG 2………..
..CHECK
Check BLEED PRESSURE on ECAM page. ECAM ENGINE page
Start ENG 2 ONCE AVAIL is displayed
for ENG 1
RRGE PW
ENG 1 is started first because it powers the blue hydraulic system, which pressurizes the parkingbrake.
DO NOT SET the MASTER switch ON before all amber crosses and messages have disappeared on
engine parameters (upper ECAM display).
ENG 1 is started first because it powers the blue hydraulic system, which pressurizes the parkingbrake.
DO NOT SET the MASTER switch ON before all amber crosses and messages have disappeared on
engine parameters (upper ECAM display).
PFPF PNFPNFA330
GE:
N1………………………about 23%
EGT…………………….about 360° CN2………………………about 63%
FF………………………about 550 kg/h (1210 lb/h)
PW:EPR……………………about 1.010%
EGT……………………about 320° C
N1………………………about 23%
RR:
EPR……………………about 1.015%
EGT……………………about 380° CN1………………………about 22.6%
N2………………………about 47%
NORMAL ENGINE IDLE PARAMETERSAT ISA SEA LEVEL
FF…………………about 580 kg/h (1280 lb/h)N2…………………about 59%
FF…………………about 820 kg/h (1800 lb/h)N3…………………about 63%
Upper ECAM
Lower ECAM
PFPF PNFPNFA3303.a. AFTER START
ENG START SEL…………………….……NORM
APU BLEED………………………………….OFF
ECAM STATUS…………………….………CHECK
ECAM DOOR PAGE…...………………….CHECK
ANNOUNCE….……”CLEAR TO DISCONNECT”
1. GND SPLRS…………………………………ARM
2. RUD TRIM…………………………………RESET
3. FLAPS…………………………………………SET
4. PITCH TRIM…………………………………..SET
ENG ANTI ICE…………………………AS RQRD
WING ANTI ICE………………………..AS RQRD
6. APU MASTER SW……………………………OFF
End of START sequence : Signal for PNF actions
Pedestal
OverheadPanel
5.
5
6
4
1
2
3
ENGINE WHEEL
ENG START SELback to NORM
ECAM
Turn APU BLEED OFF just after engine start
to avoid ingesting engine exhaust gases.
Turn APU BLEED OFF just after engine start
to avoid ingesting engine exhaust gases.
PFPF PNFPNFA330
Set Takeoff CG on the pitch trim wheel
For this purpose, use the actual CG indicated on theECAM :
The Takeoff CG value must be within the green bandlimits.
PITCH TRIM SET
4
PFPF PNFPNFA330
WHEN ARE ENG & WING ANTI ICE REQUIRED ?
CAUTION ! In icing conditions, minimise flight duration with the slats extended.
OAT or TAT 10° C with visiblemoisture in the air, standingwater, slush, ice or snow on
the taxiways or runways
ICINGICINGCONDITIONSCONDITIONS
expected
ENG ANTI ICEmust be ON
Engine anti-ice•
Wing anti-ice
WING ANTI ICErecommended
Prevent ice formation
Ice accumulation on thewing leading edges
Ice accumulation on thevisual ice indicator or on
the windshield wipers
OR
OR
PFPF PNFPNFA3303.b. AFTER START
To stabilize engine hot section temperature:
If icing conditions :
3 min (GE) / 5 min (PW & RR) / 3 min (RR ifengines have been stopped for 1.5 hr or less)
minimum at or near IDLE
Enginestarted
High power
t
GE : RR : PW :
engines started
Observe the ECAM MEMO:
NWS TOWING FAULT LT extinguished…CHECK
AFTER START C/L
t (min.)0 2
If nosewheel steering has exceeded 93°
NO GO
Maintenance action required
FAULT
FAULT
Illumination of the redoversteer warning light
PFPF PNFPNFA3303.b. AFTER START
To stabilize engine hot section temperature:
If icing conditions :
3 min (GE) / 5 min (PW & RR) / 3 min (RR ifengines have been stopped for 1.5 hr or less)
minimum at or near IDLE
Enginestarted
High power
t
GE : RR : PW :
engines started
Observe the ECAM MEMO:
NWS TOWING FAULT LT extinguished…CHECK
AFTER START C/L
t (min.)0 2
NW STRG still disconnected+
at least 1 engine running
PFPF PNFPNFA3303.b. AFTER START
To stabilize engine hot section temperature:
If icing conditions :
3 min (GE) / 5 min (PW & RR) / 3 min (RR ifengines have been stopped for 1.5 hr or less)
minimum at or near IDLE
Enginestarted
High power
t
GE : RR : PW :
engines started
Observe the ECAM MEMO:
NWS TOWING FAULT LT extinguished…CHECK
AFTER START C/L
t (min.)0 2
On ground, perform an ENGINE RUN-UP (60% N1 minimum)for approximately 30 sec prior to higher thrust in order to
centrifuge any ice from the engine’s rotating parts
If icing conditions > 30minOR
Significant engine vibration•
ENG ANTI ICEON
Continuous ignitionautomatically selected•
PFPF PNFPNFA3303.b. AFTER START
To stabilize engine hot section temperature:
If icing conditions :
3 min (GE) / 5 min (PW & RR) / 3 min (RR ifengines have been stopped for 1.5 hr or less)
minimum at or near IDLE
Enginestarted
High power
t
GE : RR : PW :
engines started
Observe the ECAM MEMO:
NWS TOWING FAULT LT extinguished…CHECK
AFTER START C/L
t (min.)0 2
On ground, perform an ENGINE RUN-UP (50% N1recommended) for 10 sec prior to take off in order tocentrifuge any ice from the engine’s rotating parts
If holding on the ground, perform it once every hour
If icing conditions&
OAT 1° C•
PFPF PNFPNFA3303.b. AFTER START
To stabilize engine hot section temperature:
If icing conditions :
3 min (GE) / 5 min (PW & RR) / 3 min (RR ifengines have been stopped for 1.5 hr or less)
minimum at or near IDLE
Enginestarted
High power
t
GE : RR : PW :
engines started
Observe the ECAM MEMO:
NWS TOWING FAULT LT extinguished…CHECK
AFTER START C/L
t (min.)0 2
On ground, perform PERIODIC ENGINE RUN-UP (50% N1recommended) to centrifuge any ice from the engine’srotating parts at intervals not greater than 15 min.If icing conditions
&OAT 3° C
Take off should be preceded by a STATIC RUN-UP (50% N1recommended) with observation of all primary parameters
•
ENG ANTI ICEON
Continuous ignitionautomatically selected•