CODE : 00Z
SERVICE MANUAL
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specifiedones for maintaining the safety and performance of the set.
This document has been published to be usedfor after sales service only.The contents are subject to change without notice.
XEA207SM2E
LEAD-FREE SOLDER MODEL
ELECTRONIC CASH REGISTER
XE-A207XE-A217
MODEL XE-A307
CHAPTER 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 2. INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CHAPTER 3. MASTER RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CHAPTER 4. MAINTENANCE, DISASSEMBLY AND ASSEMBLY . . 16
CHAPTER 5. HARDWARE DESCRIPTION . . . . . . . . . . . . . . . . . . . 26
CHAPTER 6. DIAGNOSTIC PROGRAM DESCRIPTION . . . . . . . . 30
CHAPTER 7. PWB LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CHAPTER 8. CONNECTOR PIN LAYOUT . . . . . . . . . . . . . . . . . . . 40
XE-A207W/B
XE-A217W/B
XE-A307
XE-A207/A217/A307 LEAD-FREE SOLDER
■ LEAD-FREE SOLDER
The PWB’ s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. Thealphabet following the LF mark shows the kind of lead-free solder.
Example:
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use soldering iron is rec-ommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior toconventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed the heat-resistive tem-perature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after com-pletion of soldering work. If the soldering iron tip is discolored black during soldering work, cleanand file the tip with steel wool or a fine filer.
5mm
Lead-Free
Solder composition code (Refer to the table at the right.)
<Solder composition code of lead-free solder>
Solder composition
Sn-Ag-Cu
Sn-Ag-BiSn-Ag-Bi-Cu
Sn-Zn-Bi
Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
Bi-Sn-Ag-PBi-Sn-Ag
a
b
z
i
n
s
p
Solder composition code
a
CAUTIONS
THERE IS A RISK OF EXPLOSION IF THE BATTERYIS REPLACED BY AN INCORRECT TYPE.
PROPERLY DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
CAUTIONSn Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to the instructions.n Do not leave the unit with the battery discharged for more than one month.
It will shorten the battery life. If the unit is left unused for a long period, be sure to charge the battery fully. Also note that the battery must be charged periodically (once a month) because it will discharge naturally.
CHAPTER 1. SPECIFICATIONS
1. SPECIFICATIONS
XE-A207W/A207B, XE-A217W/A217B
*Specifications and appearance are subject to change without noticefor improvement.
XE-A307
*Specifications and appearance are subject to change without noticefor improvement.
Model • XE-A207W/XE-A207B
• XE-A217W/XE-A217B
Dimensions 335 (W) x 424 (D) x 326 (H) mm
Weight Approx. 11.0 kg
Power Source Official (nominal) voltage and frequency
Power Consumption
Stand-by • 9 W (When the official voltage is220 to 230 V, 50 Hz/60 Hz)
• 10 W (When the official voltageis 230 to 240 V, 50 Hz)
Operating • 33 W (max.) (When the officialvoltage is 220 to 230 V, 50 Hz/60 Hz)
• 34 W (max.) (When the official voltage is 230 to 240 V, 50 Hz)
Working Temperature
0 to 40 °C (32 to 104 °F)
Humidity 10 % to 90 %
Display Operator display LCD display with Tilt mechanism160 (W) x 64 (H) (dots)
Customer display 7-segment display
Printer Type Drop-in thermal printer
Printing speed Approx. 15 lines/second
Printing capacity 30 digits
Other functions • Receipt (ON-OFF) function
• Compression print for an elec-tronic journal
Logo Graphic logo printing
Size 360 pixel (W) x 130 pixel (H)
Logo messageprinting
Logo message for the receipt(max. 30 characters x 6 lines)
Paper Roll Width 58 mm
Max. diameter 80 mm
Quality High quality (0. 06 to 0.08 mmthickness)
Cash Drawer 5 slots for bills and 8 for coin denominations
Accessories BASIC USER MANUAL
1 copy
Standard key sheet
1 (placed under keyboard cover)for XE-A217W/XE-A217Bonly
Text preset key sheet
1 (placed under keyboard cover)for XE-A217W/XE-A217B only
Paper roll 1
Drawer lock key 2
Fixing angle bracket
1
Model XE-A307
Dimensions 360 (W) x 425 (D) x 330 (H) mm
Weight Approx. 12.0 kg
Power Source Official (nominal) voltage and frequency
Power Consumption
Stand-by • 9.8 W (When the official voltageis 220 to 230 V, 50 Hz/60 Hz)
• 9.3 W (When the official voltageis 230 to 240 V, 50 Hz)
Operating • 37.8 W (max.) (When the officialvoltage is 220 to 230 V, 50 Hz/60 Hz)
• 35.1 W (max.) (When the officialvoltage is 230 to 240 V, 50 Hz)
Working Temperature
0 to 40 °C (32 to 104 °F)
Humidity 20 % to 90 %
Display Operator display LCD display with Tilt mechanism 160 (W) x 64 (H) (dots)
Customer display 7-segment LED display
Printer Type Two-station thermal printer
Printing speed Approx. 12 lines/second
Printing capacity 30 digits each for receipt/journal paper
Other functions • Receipt (ON-OFF) function
• Compression print for the journaland electronic journal
• Receipt and journal independentpaper feed function
Logo Graphic logo printing
Size 360 pixel (W) x 130 pixel (H)Area of black must be less than35% of all area.
Logo messageprinting
Logo message for the receipt(max. 30 characters x 6 lines)
Paper Roll Width 57.5 ± 0.5 mm
Max. diameter 80 mm
Quality High quality (0.06 to 0.08 mmthickness)
Cash Drawer 5 slots for bills and 8 for coin denominations
Accessories Basic User Manual
1 copy
Paper roll 2
Take-up spool 1
Paper holding plate
1
Drawer lock key 2
Fixing angle bracket
1
Battery caution label
1
XE-A207/A217/A307 SPECIFICATIONS
– 1 –
2. EXTERNAL VIEW
■ FRONT VIEWXE-A207W/A207B
XE-A217W/A217B
XE-A307
■ Rear view
3. ACCESSORIES
Printer coverOperator Display
Keyboard
Drawer
Drawer lock
SD card slot
Printer cover
Operator Display
Keyboard
Drawer
Drawer lockSD card slot
Printer cover
Keyboard
Drawer
Drawer lockSD card slot
Operator Display
Customer display
RS232C
SK
1-1
Drawer lock key: 2 Paper roll: 1 (XE-A207X/B,XE-A217W/B)Paper roll: 2 (XE-A307)
BASIC USER MANUAL: 1
Standard key sheet: 1 (for XE-A217W/A217B (placed under keyboard cover))
Text preset key sheet: 1(for XE-A217W/A217B (placed under keyboard cover))
XE-A207/A217/A307 SPECIFICATIONS
– 2 –
4. DISPLAYS■ OPERATOR DISPLAYSCREEN EXAMPLE 1 (REG MODE)
SCREEN EXAMPLE 2 (PGM MODE)
The display can be tilted back and forth to the best operational viewing angle.
Note: Do not try to force the display beyond its full position.
■ CUSTOMER DISPLAY
■ SCREEN SAVE MODEWhen you want to save the electric power or save the display’s life, use the screen save function. This function can turn the LCD backlight off whenany server does not operate the register for an extended period of time. You can program the time for which your register should keep the normal sta-tus (in which the backlight is “ON”) before it goes into the screen save mode. This machine will enter the screen save mode two minutes later by default.To go back to the normal mode, press any key.
PLU level shift indicator (L1-L3) Shows the PLU level currently selected.
Receipt ON/OFF status indicator (R) Appears when the receipt ON-OFF function signs OFF.
VAT shift status indicator (V) Appears when the VAT status is shifted.
Electronic journal near full indicator ( ) Appears ( ) when the used memory is 80%.
Appears ( ) when the used memory is 90%.
Appears ( ) when the used memory is 95%.
Sentinel mark (X) Appears when the cash in drawer exceeds a programmed sentinel amount. The sentinel check is per-formed for the total cash in drawer.
Sales information area:
Mode name Status information
Clerk code
When a transaction information occupies more than 2 lines, scroll key(s) appears to indicate you can scroll to the direction. Sales information you have just entered such as items and prices will appear between 1st line and 2nd line. Total is always appear at 3rd line. Numeric Entry Area:Status area:
Programming area:Programmable items are listed.
Status area:
Mode name Clerk code
XE-A207/A217/A307 SPECIFICATIONS
– 3 –
5. KEYBOARD (XE-A207W/XE-A207B)
5-1. KEYBOARD LAYOUT
5-2. FUNCTION KEY LIST
* In this manual each department key is represented like in order to distinguish it from direct price lookup keys.
Receipt paper feed key
Electronic journal view key
Function menu key
Auto menu key
Paid out key
Percent 1 key
Void key
Refund key
Help key
Discount key
Multiplication key
Decimal point key
Clear key
Numeric key
Price lookup/Sub department key
Department code entry key
Department shift key
Clerk code entry key
Department 1-32 key
Cursor (up/down arrow) key
Mode key
Escape/Cancel key
Credit 1 key
Payment menu key
Check 1 key
Non-add code/Time display/Subtotal key
Total/No sale key
~
~
XE-A207/A217/A307 SPECIFICATIONS
– 4 –
6. KEYBOARD (XE-A217W/XE-A217B)
6-1. KEYBOARD LAYOUT
6-2. PROGRAMING KEYBOARD LAYOUT
XE-A207/A217/A307 SPECIFICATIONS
– 5 –
6-3. FUNCTION KEY LIST
* In this manual each department key is represented like in order to distinguish it from direct price lookup keys.
Receipt paper feed key
Help key
Guest check receipt key
Electronic journal view key
Function menu key
Auto menu key
Clerk code entry key
Price lookup/Sub department key
Discount key
Percent 1 key
Paid out key
Refund key
Void key
Value added tax shift key
Cursor (up/down arrow) key
Mode key
Escape/Cancel key
Department 1-6 key
Multiplication key
Decimal point key
Clear key
Numeric key
Payment menu key
Department code entry key
Credit 1 key
Check 1 key
PLU level shift 1 to 3 keys
Non-add code/Time display/Subtotal key
Guest lookup key
Total/No sale key
New balance key
Direct PLU key
~
~
~
~
XE-A207/A217/A307 SPECIFICATIONS
– 6 –
6-4. INSERTING THE KEYBOARD SHEETTwo types of keyboard sheets are installed on the cash register; one forordinal use and one for text programming.Insert the keyboard sheet between the keyboard cover and the cabinetas illustrated below.
1) Turn over the keyboard cover.
2) Insert the keyboard sheet into the slit.
3) Close the keyboard cover.
Note:
• Do not spread the keyboard cover too far as it might tear.
• Replace the keyboard sheet with a new one if by chance it gets wet.Use of a wet keyboard sheet may cause problems.
• Be sure to use only SHARP-supplied keyboard sheets. Thick or hardsheets make key operations difficult.
• Smooth the keyboard sheet evenly under the keyboard cover, withoutany folds or wrinkles, to ensure easier operation.
• If you require a new keyboard sheet, please contact your dealer.
7. KEYBOARD (XE-A307)
7-1. KEYBOARD LAYOUT
Keyboard sheet
Keyboard cover
1
2
XE-A207/A217/A307 SPECIFICATIONS
– 7 –
7-2. FUNCTION KEY LIST
Receipt paper feed key
Journal paper feed key
Function menu key
Auto menu key
Paid out key
Percent 1 key
Void key
Refund key
Help key
Discount key
Multiplication key
Decimal point key
Clear key
Numeric key
Price lookup/EAN key
Department code entry key
Department shift key
Clerk code entry key
Department 1-40 key
Cursor (up/down arrow) key
Mode key
Escape/Cancel key
Credit 1 key
Electronic journal view key
Foreign currency exchange key
Check 1 key
Payment menu key
Non-add code/Time display/Subtotal key
Total/No sale key
XE-A207/A217/A307 SPECIFICATIONS
– 8 –
8. PRINTER
8-1. SPECIFICATIONS
8-2. CLEANING THE PRINTERWhen the printed text is getting dark or faint, paper dust may be stuck tothe print head, sensor and/or roller.Clean them as follows:
Caution:
• Never touch the print head with a tool or anything hard as it may dam-age the head.
• The paper cutter is mounted on the printer cover. Be careful not to cutyourself.
1) Select the OFF mode.
2) Remove the printer cover.
3) Life up the printer roll arm.
4) Remove the paper roll.
5) Clean the print head with a cotton swab or soft rag moistened withethyl alcohol or isopropyl alcohol.Clean the roller in the same manner.
6) Reset the paper roll correctly.
9. DRAWER
10. SUPPLIES
Part number LTPC235 (SII)
Type 1 sheet thermal (58mm paper) Roll paper drop in
Printing system Line thermal
Number of digits 30 digits/line
Print speed Approx. 15 lines / sec
Character size 3.0(H)mm x 1.25(W)mm
Printer cover key No
Cutter type Manual Cutter
Paper end sensor • Near end sensor : No
• End sensor : Yes
Paper width 58mm x 80φ
MCBF 5 million lines
Printer roll arm
Print head
Roller
Type SK-420 base (New)
Size 355(W) x 420(D) x 125(H) mm
Color White: XE-A207W/XE-A217W, XE-A307Black: XE-A207B/XE-A217B
Money case type Removable type
Coin case type Removable type
Compartment 5B/8C
Lock system Front lock
Bell No
Open sensor No
Drawer separation No
Method of fixation Fixed
Name Parts code Price rank Description
Thermal roll paper TPAPR6656RC05 BA 5 ROLLS/PACK
420mm
355mm
125mm
XE-A207/A217/A307 SPECIFICATIONS
– 9 –
11. SD CARD
11-1.USABLE SD CARD
11-2.CAN DO IT WITH A SD CARD
12. OPTION
• Water proof key cover (For XE-A207W/A207B, XE-A307): GCOVB2769BHZZ
Size 2GB,4GB, 8GB, 16GB, 32GB (SDHC memory card)
Recommended maker
• San Disk (4GB-32GB):SDSDB-4096-J95, SDSDH-OO8G-J95, SDSDX3-O16G-J31A, SDSDB-O32G-J95A
• Panasonic (2GB-4GB): RP-SDP02GE1K , RP-SDN02GE1A, RP-SDQ04GE1K, RP-SDN04GE1A
Sort Text Data/List
SD card formatting
FORMATTING When the SD card is not formattedyet, take the formatting operation.
Folder SEL ECTFOLDER
The programmed code is used thefile folder structure. Up to 8 digitscode can be programmed.
CR EATEFOLDER
The master folder can be createdfor the data file.
Data saving SALES DATA Sales data
EJ DATA Electronic journal data
IND. PROGRAM Select the individual programmingdata:DEPARTMENT, PLU, GRAPHIC LOGO
ALL PROGRAM All programming data
ALL RAM DATA All RAM data
Data loading IND. PROGRAM Select the individual programmingdata:DEPARTMENT, PLU, GRAPHIC LOGO
ALL PROGRAM All programming data
ALL RAM DATA All RAM data
XE-A207/A217/A307 SPECIFICATIONS
– 10 –
CHAPTER 2. INSTALL
■ Initializing the Cash Register
For the cash register to operate properly, you must initialize it before programming for the first time.Follow this procedure.
1) Remove the register from its packing carton.
2) Insert the plug into the AC outlet.
Caution:
• This operation must be performed without batteries loaded.
• Never install the batteries into the cash register before initializing it. Before you start operating the cash register, you must first initialize it, theninstall two new alkaline batteries LR6 (“AA” size) on the register. Otherwise, distorted memory contents and malfunction of the cash register willoccur.
• Never install the resister in saline areas (e.g.:close to the sea).Installing the resister in such locations could cause component failure with the corrosion.
(1) LANGUAGE SELECTION
1) Display the “Language Selection” after turning on the power.
2) Press the numeric key for the number of your language.
After selecting the language, the register is initialized.According to the displayed instruction, perform the setting.
(2) SETTING THE DATE AND TIME
1) Display the “DATE/TIME setting”.
2) Enter the date in 6 digits. For example, enter “050611” for June 5,2011.
3) Press the [ 4 ] key to select the time setting.
4) Enter the time in 4 digits. For example, enter “1430” for 2:30pm.
5) Press the [TL/NS] key to set the date and time.
(3) SETTING THE TAX RATE
1) Select the tax number (1 to 4) to set the tax rate.
2) Enter the tax rate in 7 digits (leading zeros may be omitted). Forexample, press the [ 7 ] key to set 7%.
3) To set the second and later tax rates, press the [ 4 ] key.
4) Press the [TL/NS] key to set the tax rate.
(4) CALCULATION OF VAT RATE
VAT is included in the entered price, and the tax amount is calculatedwhen tendered according to the VAT rate programmed.By default, VAT1 is assigned to all items.
The HELP function instructs you how to assign VAT to department. Afterpressing the [ 7 ] key, press the [HELP] key to access the HELP.
(5) SETTING THE MODE PASS CODE
1) Select the mode to set the pass code using the [ 2 ] or [ 4 ] keys.
2) Enter the code in 4 digits using the numeric keys.
3) Press the [TL/NS] key to set the mode pass code.
If no pass code is set, press the [TL/NS] key.
(6) SETTING THE MANAGER PASS CODE1) Enter the code in 4 digits using the numeric keys.
2) Press the [TL/NS] key to set the manager pass code.
If no pass code is set, press the [TL/NS] key.
(7) SETTING THE RECEIPT LOGO1) To change the default logo text, press the [(DEL)] key to delete the
texts in each line. Enter the text using the character keys to print on the receipt.
2) Press the [TL/NS] key to set the receipt logo.
(8) TEXT ENTRY METHOD<XE-A207W/A207B, XE-A307>
There are two ways for programming text; using character keys on thekeyboard or entering character codes with numeric keys on the key-board.You can enter characters according to the small figures printed in thelower position of the numeric keys.3 Refer to page 4 “5-1. KEYBOARD LAYOUT”. (XE-A207W/A207B)3 Refer to page 7 “7-1. KEYBOARD LAYOUT”. (XE-A307)For example to enter “A”, press the [ 8 ] key. To enter “B”, press the [ 8 ]key twice.
<XE-A217W/A217B >
There are two ways for programming text; using character keys (on theprogramming key sheet) or entering character codes with numeric keyson the keyboard.To enter numerals, letters and symbols, simply press the correspondingcharacter on the programming key sheet.
Note: The HELP function instructs you how to set the logo message.After entering “13”, press the [HELP] key to access the HELP.
XE-A207/A217/A307 INSTALL
– 11 –
(9) INSTALLING BATTERIESBatteries must be installed in the cash register to prevent data and pro-grammed contents from being lost from the memory in case of acciden-tal disconnection of the AC cord or power failure. Please install two newLR6 (“AA” size) batteries before programming and operating the cashregister.
1) Remove the printer cover.
2) Open the battery cover next to the paper roll cradle.
3) Install two new LR6 (“AA” size) batteries.
4) Close the battery cover.
5) Replace the printer cover.
(10) INSTALLING A PAPER ROLL(XE-A207W/B, XE-A217W/B)
Always install the paper roll even when you set the register for not print-ing receipt in REG mode.
1) Remove the printer cover.
2) Lift up the print roller arm.
3) Set the paper correctly in the paper roll cradle.
Note: Before placing a new paper roll in the paper roll cradle, cut off thepasted (taped) part of the paper and confirm that the cut end ofthe paper is straight.
4) Feed the end of the paper along with the paper positioning guidesas per the diagram.
5) While holding down the paper, slowly close the print roller arm.
Note: If the print roller arm is not securely locked, printing is not doneright. If this problem occurs, open the arm, and close the arm asinstructed above.
6) Cut off the excess paper and replace the printer cover.
7) Press the [ 2RECEIPT] key to make sure the paper end comes outof the printer cover and clean paper appears.
Note: If the paper end does not come out, open the printer cover, andpass the paper end between the paper cutter and the paperguide of the printer cover, and replace the printer cover.
Print roller arm
Correct Incorrect
To the printer To the printer
Paper positioning guides
XE-A207/A217/A307 INSTALL
– 12 –
(11) INSTALLING A PAPER ROLL (XE-A307)The register can print receipts and journals. For the printer, you mustinstall the paper rolls (receipt and journal paper rolls) provided with theregister.
1) Remove the printer cover.
2) Lift up the print roller arm of the receipt side.
3) Set a paper roll in the paper roll cradle of the receipt side as per thediagram.
4) Feed the end of the paper along with the paper positioning guidesas per the diagram.
5) While holding down the paper, slowly close the print roller arm ofthe receipt side, and push down the arm until you hear a click lock-ing the arm.
Note: If the print roller arm is not securely locked, printing is not doneright. If this problem occurs, open the arm, and close the arminstructed above.
Print roller arm
To the printer To the printer
Correct Incorrect
Paper positioningguides
XE-A207/A217/A307 INSTALL
– 13 –
CHAPTER 3. MASTER RESET
This programming is chiefly performed when the ECR is shipped, installed, or serviced.
1. MASTER RESET
Master resetting clears the entire memory and resumes initial values.Initial values of language can be selected one from following 5 kinds.
• 1 English
• 2 German
• 3 French
• 4 Spanish
• 5 Swedish
Master resetting can be accomplished by using the following “Proce-dure 1” or “Procedure 2”.
■ PROCEDURE 11) Unplug the AC cord from the wall outlet.
2) Remove 2 dry batteries and wait for 1 minute.
3) Plug in the AC cord to the wall outlet.
4) Language selection menu is displayed. Push the correspondingnumber key.
5) Set current date/time and push [TL/NS] key.
6) Set tax rate and push [TL/NS] key.
7) Set mode pass code and push [TL/NS] key.
8) Set manager pass code and push [TL/NS] key.
9) Set logo message and push [TL/NS] key.
10) REG mode screen is displayed.
11) Insert 2 dry batteries.
■ PROCEDURE 2
1) Unplug the AC cord from the wall outlet.
2) Push [receipt paper feed] key and [CL] key.
3) Plug in the AC cord to the wall outlet during the depression of above2 keys.
4) Language selection menu is displayed. Push the correspondingnumber key.
5) Set current date/time and push [TL/NS] key.
NO BATTERY
XE-A207/A217/A307 MASTER RESET
– 14 –
6) Set tax rate and push [TL/NS] key.
7) Set mode pass code and push [TL/NS] key.
8) Set manager pass code and push [TL/NS] key.
9) Set logo message and push [TL/NS] key.
10) REG mode screen is displayed.
2. PROGRAM RESET
Program resetting resumes the initial program without clearing memory.
This operation must be performed with batteries loaded.
1) Unplug the AC cord from the wall outlet.
2) Push [receipt paper feed] key and [0] key.
3) Plug in the AC cord to the wall outlet during the depression of above2 keys.
4) MODE menu screen is displayed.
XE-A207/A217/A307 MASTER RESET
– 15 –
CHAPTER 4. MAINTENANCE, DISASSEMBLY AND ASSEMBLY
1. ROLL PAPER REPLACEMENT
1-1. ROLL PAPERThis register is provided with the following consumable parts:
Caution:
• Use the roll paper recommended by us only.If other roll paper is used, paper clog or other trouble may occur.
RECOMMENDABLE ROLL PAPER
Paper quality: High-quality heat-sensitive paper
Paper width: 57.5±0.5mm
Outer diameter: 81mm (Max.)
Paper thickness: 0.06 - 0.08mm
Paper weight: 52.3 - 64.0g/m2 (44 - 55kg/1,000 sheets/788 x 1,091mm)
• Do not unpack roll paper until being used.
• Use enough care to handle roll paper. It is recommended top keep roll paper at normal temperature (20°C) and normal humidity (60%) in a darkplace. When attaching printed material to the note, etc, attach it to a margin (non-printed area) with paste.
• Avoid storing under the following conditions, or discoloration of paper and printed characters may occur. - Place at high humidity (temperature above 40°C, humidity above 80%) - Dusty place - Place with direct sunlight - Place at high temperature of 60°C or above (Near a stove , a heater, or heat source such as lighted cigarette, or inside an automobile)
• Avoid the following actions, or discoloration on the paper surface or printed characters may occur. - Scratching the paper surface with your nail, pencils, or other metal, or dropping or crashing roll paper to damage the surface. - Letting roll paper be in contact with rail or water or touching with a wet hand.
• Avoid contact with the following items, plasticizing agent, organic solvent, and leather items, or discoloration on the paper surface or printed charac-ters may occur.- Highlighter pen, marker pen, mending tape, cellophane tape, adhesive agent, stamps, vermilion ink-pad, diazo copy (blue print), or rubber eraser.- Bond, thinner, alcohol, benzene, hair dressing, oil, hand cream, vinyl chloride plastic file/bag/wrap, leather items
Part Name Part Number Outer Diameter Remark
Roll paper RL140T (5 rolls/pack) 70mm Paper quality: Thermal paperPaper width: 57.5±0.5mmRL130T (5 rolls/pack) 80mm
Roll paper (High-storage type) RL141T (5 rolls/pack) 70mm
RL131T (5 rolls/pack) 80mm
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 16 –
1-2. HOW TO REPLACEWhen roll paper is nearly exhausted, red indication appears. Replace roll paper in such a case.
Caution: When roll paper is not installed to the printer or it is exhausted, the error message of “There is no roll paper. Set roll paper and press[CLEAR].” is displayed and the operation is disabled.In such a case, set roller paper and press [CLEAR] to clear the error. (The printer error code, “============” is printed.)
■ HOW TO REMOVE1) Remove the printer cover.
2) If recording paper is used, remove recording paper.Press [Paper Feed] to feed recording paper by several lines, and cutoff the roll paper, and remove the winding shaft from the bearing.
Remove the roll paper holding guide from the winding shaft, andremove recording paper.
Caution: Do not pull roll paper without press [Paper Feed]. It may dam-age the printer head.
3) Lift the printer arm.
4) Remove the remaining roll paper.
■ HOW TO INSTALL3 Refer to page 12, "(10)INSTALLING A PAPER ROLL (XE-A207W/B,
XE-A217W/B)."
3 Refer to page 13, "(11)INSTALLING A PAPER ROLL (XE-A307)."
Roll paper holding guide
Winding shaft
Cut offBearing
Roll paper holding guide
Press this section in the arrow direction to remove the winding shaft holder.
Printer arm
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 17 –
2. PRINTER CLEANING
Dust on the printer head will cause faint or darkly print. In such a case, wipe the printer head softly with dry, soft cloth. At the same time, wipe andclean the roller and the senor as well. If necessary, immerse a cloth in alcohol to clean.
Caution:
• Since the printer head and its peripheral sections and the motor surface are heated to a high temperature during operations or immediately afteroperations, use enough care to clean the printer head after cooling it down.
• Do not touch the printer head directly with bare hand or do not put a tool or some hard items near the printer head in order not to damage the printerhead.
1) Disconnect the power plug from the power outlet.
2) Remove the printer cover.
3) If the roll paper is wound around the winding shaft, separate it fromthe roll paper first, then lift the printer arm.
4) Remove the roll paper.
5) Wipe the printer head, the roller, and the sensor softly with softcloth.
6) Insert the power plug into the power outlet.
7) Attach the roll paper.3 Refer to page 12, "(10)INSTALLING A PAPER ROLL (XE-
A207W/B, XE-A217W/B)."3 Refer to page 13, "(11)INSTALLING A PAPER ROLL (XE-
A307)."
Note: When the error message of "Printer arm is lifted." is shown onthe display, press [CLEAR] to clear the display.
Printer arm
Printer head
Roller
Sensor
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 18 –
3. BATTERY REPLACEMENT
When the batteries are nearly exhausted. “ ” is indicated on the display. Replace the batteries with new AA alkaline batteries within two days.
Caution:
• When “ ” is displayed, there are no batteries or the batteries are nearly exhausted. Replace the batteries immediately. If, under this state, a serviceinterruption occurs or the power plug is disconnected, the set data and registered data are deleted.
• When “ ” is displayed during registration, complete the transaction and then replace the batteries.
• Be sure to confirm that the power plug is inserted into the power outlet before replacing the batteries. If not, the registered data will be deleted. Useenough care for that.
• The battery life is about one year. Even though “ ” is not displayed, replace the batteries at least once a year.
1) Check to confirm that the power plug is inserted into the power out-let.
2) Remove the printer cover.
3) Remove the battery case cover, and remove the old batteries.
4) Inert two AA batteries (new ones) in the proper directions of thepositive (+) and negative (-) terminals.
5) Check to confirm that “ ” and “ ” are not displayed, and attach thebattery case cover.
6) Attach the printer cover.
Caution:
• Be careful of the positive (+) and negative (-) terminals of batterieswhen inserting.
• When replacing batteries, replace two of them together. Do not mix anew one with an old one. Do not mix different types of batteries.
• Do not leave an exhausted battery in the unit. It may cause liquid spill,damaging the unit.Do not throw an exhausted battery into a fire. It may burst to cause adangerous accident.
• The batteries are of charging type and of not-charging type. Be sureto use batteries of not-charging type.
• Dispose used batteries according to the procedures set by the localauthorities.
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 19 –
4. DISASSEMBLY AND ASSEMBLY
Caution:
CAUTION BEFORE DISASSEMBLY AND ASSEMBLY
• Be sure to disconnect the power plug from the power outlet.
• Remove roll paper and winding shaft before disassembly and assem-bly.
4-1. TOP UNIT REMOVAL1) Remove the printer cover.
2) Remove the screw.
3) Lift the rear side of the top unit slightly toward you.
Caution: Since the top unit is connected with the flat cable and the earthwire, do not lift it excessively.
4) Remove the flat cable and the earth wire from the main PWB, andremove the top unit.
4-2. MAIN UNIT AND DRAWER UNIT SEPARATION
1) Remove the top unit.3 Refer to page 20, "4-1. TOP UNIT REMOVAL."
2) Remove the option angle.3 Refer to page 24, " SIO I/F PWB REMOVAL."
3) Disconnect the connector from the main PWB.
4) Remove the screw, the terminal block, and the angle.
Printer cover
screw
screw
Top unit
Earth wire
Flat cable
Connector
Screw
Screw
Screw
Terminal block
Angle
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 20 –
5) Slide the main unit toward you and lift is slightly.
Caution: Since the drawer unit is connected with the earth wire, do notlift the main unit excessively.
6) While lifting the main unit slightly, remove the screw and the earthwire from the drawer unit, and remove the main unit.
4-3. TOP UNIT
■ KEY I/F PWB AND KEY SHEET REMOVAL1) Remove the flat cable from the key I/F PWB. Remove the screw and
remove the key I/F PWB.
2) Remove the screw and the earth wire, and remove the key boardunit.
3) Remove the screw, and remove the key plate.
4) Remove the key sheet.
■ LCD REMOVAL1) Remove the screw and the earth wire, and remove the LCD unit.
2) Open the hinge.
3) Disengage the pawl, and slide the LCD rear cabinet upward to
Main unit
Earth wire
Screw
Flat cableFlat cable
Key I/F PWB Screw
Screw
Screw
Screw Screw
Key board unitEarth wire
Key board plateScrew
Screw
Screw
Key sheet
LCD unit
Earth wire
Screw
Hinge
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 21 –
remove.
4) Remove the screw, and remove the LCD angle.
5) Remove the flat cable, and remove the LCD.
■ POPUP PWB REMOVAL1) Remove the flat cable from the key I/F PWB.
2) Disengage the pawl, and remove the popup unit.
3) Disengage the pawl, and slide the popup filter downward to remove.
4) Disengage the pawl, and remove the popup PWB.
5) Remove the flat cable from the popup PWB.
LCD rear cabinet
Pawl
LCD angle
Screw
LCD
Flat cable
Flat cable
Popup unit
Pawl
Popup filter
Pawl
Popup PWBPawl
Flat cable
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 22 –
4-4. MAIN UNIT
■ MAIN PWB REMOVAL1) Remove the flat cable and disconnect the connector from the main
PWB.
2) Remove the screw, and remove the terminal block and the angle.
3) Disengage the pawl, and remove the main PWB.
■ PRINTER UNIT REMOVAL1) Remove the flat cable from the printer I/F PWB.
2) Remove the screw, and remove the earth wire and the printer angle.
3) Remove the screw and remove the printer unit. Remove the flatcable from the core.
Flat cable
Flat cable
Connector
Connector
Screw
Screw
Angle
Terminal block
Pawl
Main PWB
Flat cable
Earth wire
Earth wire
Screw
Screw
Screw
Printer angle
Printer unit
Screw
Screw
Core
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 23 –
■ PRINTER I/F PWB REMOVAL1) Remove the flat cable from the printer I/F PWB.
2) Remove the screw. Disengage the pawl, and remove the printer I/FPWB.
■ SIO I/F PWB REMOVAL1) Remove the flat cable from the SIO I/F PWB. Remove the screw,
and remove the option angle.
2) Remove the hex screw, and remove the SIO I/F PWB.
■ POWER UNIT REMOVAL1) Remove the option angle.
3 Refer to page 24, “ SIO I/F PWB REMOVAL.”
2) Remove the screw, and remove the POP cover.
3) Disconnect the connector from the main PWB.
4) Remove the screw, and remove the power unit.
Flat cable
Printer I/F PWBScrew
Pawl
Flat cable
Screw
Screw
Option angle
SIO I/F PWB
Hex screw
POP cover
Screw
Screw
Connector
Power unit
ScrewScrew
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 24 –
4-5. DRAWER UNIT
■ DRAWER SOLENOID REMOVAL1) Release the lock on the bottom surface of the drawer unit, and open
the drawer.
Caution:
• When the lock is released, the money case extends out. Be careful.
• If the drawer is locked with the drawer key, it will not open. Use thedrawer key to open the drawer.
2) Pull out the drawer, and lift it to remove from the drawer cabinet.
3) Remove the screw from the drawer cabinet, and remove the wireholder.
4) Remove the screw, and remove the drawer bottom plate.
Caution: Be careful not to catch the connector of the drawer solenoidharness by the hole in the drawer cabinet.
5) Remove the screw, and remove the drawer solenoid.
Caution: When assembling, be sure to engage the drawer solenoid plunger with the lock.
Lock
Drawer
Drawer
Wire holder
Screw
Drawer bottom plate
Screw
ScrewScrew
Screw
Drawer solenoid
ScrewPlunger
Lock
XE-A207/A217/A307 MAINTENANCE, DISASSEMBLY AND ASSEMBLY
– 25 –
CHAPTER 5. HARDWARE DESCRIPTION
1. HARDWARE SPECIFICATION OUTLINE
Item Specification
CPU 16bit MPU H8S/2373 (Manufacturer: RENESAS) *33MHz
PRINTER XE-A207/A217: Line thermal printer 384 dots/ 58mm wide x1 pcXE-A307: Line thermal printer 384 dots/ 58mm wide x2 pcs
SRAM 4Mbit (Manufacturer: RENESAS)
ROM For programs 16Mbit Flash-ROM (Manufacturer: MACRONIX)
For data 16Mbit Flash-ROM (Manufacturer: MACRONIX)
DISPLAY Main STN LCD 160x64 dots (Manufacturer: GOWORLD) Screen size(V.A) 85.00mm (H) x 40.00mm (V)(A.A) 81.585mm (H) x 36.785mm (V)
Customer 7seg LED x 7 digits7seg LED x 10 digits (For Singapore)
KEY Normal KEY XE-A207/A307: MAX 66
Flat KEY XE-A217: MAX 119
Mode S/W N/A
I/F USB N/A
SD 1slot
Drawer 1port
*Standard Drawer to be connected
RS232 1port [D-Sub x1]
EFT N/A
BUZZER PIEZO BUZZER
POWER SUPPLY POWER TRANS
BATTERY Back Up Size AA battery x 2pcs(Recommended: Toshiba, Hitachi Maxell, Panasonic)
DRAWER Standard
XE-A207/A217/A307 HARDWARE DESCRIPTION
– 26 –
2. BLOCK DIAGRAM
FROM 16Mbit #CS0 space (H'000000 H'1FFFFF)
PROM 8Mbit #CS2 space(H'400000 H'4FFFFF)
D15 D0 (16bit width)
D15 D0 (16bit width)
D15 D8 (8bit width)
#CS4
#CS0
#CS2
#CS5
3toLINE DECORDERS 74HCT138 x2
P63 60 (4bit width)KEY STROBE (max 13bit width)
SINK DRIVER
SIO 2 BUFFER 74LV125A
SD CARD
RS232 DRIVER ICL3243ECA
RS232 D-SUB9
RAM 16KByteROM LESS
P46 P45 SINK DRIVER DRAWER
33MHz
SIO 4
PRINTER UNIT
PRINTER UNIT
#RESET
#POFF #IRQ15
#RES
SIO 0
32.768kHz
3.3VB
RTC
3.3VB
SRAM 4Mbit #CS4 space (H'800000 H'8FFFFF)
SIO 3 LCD DRIVER
FROM 16Mbit #CS1 space (H'200000 H'3FFFFF)
D15 D0 (16bit width)
#CS1
KEY RETURN (10bit width)
D7 D0 (16bit width)
MOTOR DRIVERLV8711T
#CS6
SIO 1
DAT
A B
US
AD
DR
ES
S B
US
P6
36P
0
P1
31P
0
PG4
P82
8bit D F/F 74HCT374 #CS6 space
#CS5 space
(H'C00000)
4P1
61P
*
#IRQ14
3.3VB
#RESET
PH3
D6 D0 (16bit width)
D7 D0 (16bit width)D5 D0 (16bit width)
#CS2
6bit D F/F 74LV174A #CS2 space (H'400000)
P97 P90 P47,P46
H8S/2373
8bit OCTAL BUFFERS74LV244A x1
#CS5 space(H'A00000)
XE-A307 only
XE-A307 only
Each kind sensor input
MOTOR DRIVER
LV8711T
6bit D F/F74LV174A
(H'A00000)XE-A307 only #CS5
XE-A207/A217/A307 HARDWARE DESCRIPTION
– 27 –
3. HARDWARE CONFIGURATION DIAGRAM
PRINTER UNITPRINTER UNITXE-A307 only
POWER TRANS
BATTERY DRAWER
SIO PWB UNIT
SD CARD SLOT
LCD UNIT
KEY I/F PWB UNIT
KEY BOARD UNIT
LED PWB UNIT
MAIN PWB UNIT
XE-A207/A217/A307 HARDWARE DESCRIPTION
– 28 –
4. SIGNAL CONNECTION DIAGRAM
Connection between the Host (PC) and the Terminal (ECR)
Note: If the connector of the Host PC is “9 PIN D-SUB,” the PIN num-ber is the same as that of the ECR.
5. SETTING OF RS232 PORT
The signal of 9-pin for RS232 port can be changed to “RI” or “+5V” bypositioning the short pin of “SP3” on the main PWB. However the factory-shipped location of the short pin varies dependingon the models.
Specifications of RS232 port
Usage: For Standard RS232 port
Connector: D-SUB 9pin
Data rate: max. 38,400 bps.
Power Supply: 5V/400mA (*)
Pin assign
* Default Setting
XE-A207/A217: RI (SP3: 2pin - 3pin)XE-A307: +5V (SP3: 1pin - 2pin)
Setting of SP3
SD Transmitted Data
RD Received Data
DTR (ER) Data Terminal Ready
DSR (DR) Data Set Ready
RTS (RS) Request To Send
DCD (CD) Data Carrier Detector
CTS (CS) Clear To Send
FG Frame Ground
9PIN D-SUBPC side
9PIN D-SUBECR side
Pin No. Signal Name
1 CD
2 RXD
3 TXD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 (*) RI/+5V
Signal Setting of SP3
RI 2pin, 3pin
+5V 1pin, 2pin
SP3
3RI
2+5V
1
SP3
XE-A207/A217/A307 HARDWARE DESCRIPTION
– 29 –
CHAPTER 6. DIAGNOSTIC PROGRAM DESCRIPTION
By selecting SERVICE from the DIAG MENU, the following screen is
displayed in the LCD.
The selected item is highlighted in the displayed menu.
You can change the selected item by using the [ 2 ] / [ 4 ] key, and
press the [TL/NS] key to execute the selected item.
1. DIAGNOSTIC PROGRAM START PROCEDURES
1) Check to see that the SD card is in place.
2) Set the paper roll.
3) Check to see that the AA batteries are set.
4) Set the RS232C loopback connecter.
5) Plug the AC cord to the outlet while holding down the [RECEIPT]
key and [CL] key.
6) Language selection menu is displayed. Push the corresponding
number key.
7) Set current date/time and push [TL/NS] key.
8) Set tax rate and push [TL/NS] key.
9) Set mode pass code and push [TL/NS] key.
10) Set manager pass code and push [TL/NS] key.
11) Set logo message and push [TL/NS] key.
12) REG mode screen is displayed. Push the [MODE] key.
13) Enter “99999999,” confirm that the screen displays as below, andthen press the [TL/NS] key.
14) The following screen is displayed in the LCD.
SERVICE DIAGKEY SENSOR
SD CARD LED&BZ DRAWERLCD RS232CA/D PRINTERROM
RAMCLOCK
SERVICE DIAG MENU
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 30 –
15) Make “4. DIAGNOSTIC” highlighted with the [ 2 ] key or [ 4 ] key,and press the [TL/NS] key.
16) The following screen is displayed in the LCD.
17) Enter “907 · .”
18) The following screen is displayed in the LCD.
19) Confirm that “SERVICE” is highlighted, and press the [TL/NS] key.
2. KEY
1) Press any key other than the [RECEIPT] and [TL/NS] key.
2) Press the [TL/NS] key at the end.
If you make a wrong operation, press the [CL] key three times to startover from the beginning.After the test result is displayed and printed out, press the [TL/NS] keyagain to go back to the previous screen.
S1: SUM1
S2: SUM2
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
CHECK SUM: 1509(XE-A207)37BF(XE-A217)15A2 (XE-A307)
3. SENSOR
SENSOR: This inspects the sensor circuit of the printer.
Result of detecting whether the printer paper is available.(YES: Paper available, NO: No paper)
1) Check the status of SENSOR.(The status of SENSOR is displayed in real time at an interval of 1second.)
2) Press the [TL/NS] key to end the test.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
PASSWORD? ____
DIAG MENU
SERVICE
Specified SUM
Current SUM (It changes each time the key is pressed.)
Test Result
KEY NORMALKEY CORD:XXX S1:XXXX S2=YYYY NG
LCD display (when the test result is NG.)
KEY XXXX-YYYY - NG
Printout (when the test result is NG.)
KEY NORMALKEY CORD:XXX S1:XXXX S2=YYYYOK
LCD display (when the test result is OK.)
KEY XXXX-YYYY - OK
Printout(when the test result is OK.)
SENSOR PPR1:NO
XE-A207/A217(when PPR1 is NO.)LCD display
SENSOR PPR1:NO PPR2:NO
XE-A307 (when PPR1,PPR2 are NO.)
SENSORPAPER1 NO
XE-A207/A217(when PPR1 is NO.)Printout
SENSORPAPER1 NO PAPER2 NO
XE-A307(when PPR1,PPR2 are NO.)
SENSOR PPR1:YES
XE-A207/A217(when PPR1 is YES.)LCD display
SENSOR PPR1:YES PPR2:YES
XE-A307(when PPR1,PPR2 are YES.)
SENSORPAPER1 YES
XE-A207/A217(when PPR1 is YES.)Printout
SENSORPAPER1 YESPAPER2 YES
XE-A307(when PPR1,PPR2 are YES.)
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 31 –
4. SD CARD
This detects the SD card, and displays the status of Write Protect in realtime. Also, it displays the CID register of the SD card.
Press the [TL/NS] key to end the test.
CD: CARD DETECT
WP: WRITE PROTECT
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
5. LED & BUZZER
This tests the LED display and Buzzer.
LED display
The following display modes are repeated.
• Segment display
The segments light up in the following pattern. The unit makes a shortbeep every time the [TL/NS] key is pressed, and it goes on to the nextpattern.
• Sift display
The segments light up in the following pattern. The unit makes a shortbeep every time the [TL/NS] key is pressed, and it goes on to the nextpattern.All the segments light up at the end, and it keep beeping.
By pressing the [TL/NS] key, this test ends with OK.
By pressing any key other than the [TL/NS] key, this test ends with theresult of NG.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
SD CARD
CD: NO , WP: NO CID:XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
LCD display CD NO, WP NO
SD CARD CD:NO ,WP:NO CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
Printout CD NO, WP NO
SD CARD
CD: YES , WP: YES CID:XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
LCD display CD YES, WP YES
SD CARD CD:YES ,WP:YES CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
Printout CD YES, WP YES
LED &BUZZERTL:OK,OTHER:NG
LCD display
The rest of the illustrations are omitted.
The rest is omitted.
The rest is omitted.
"A" is displayedinstead of "10."
LED NG
Printout (when the test result is NG.)
OKLED
Printout (when the test result is OK.)
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 32 –
6. LCD
The following screen is displayed. The menu items can be selected inthe same way as other menus.By selecting “EXIT,” it goes back to the Main Menu.
6-1. CONTRASTAmong the displayed menu items, the selected item is displayed inreversed characters.
1) Change the selected item by using the [ 2 ] / [ 4 ] key.
2) By pressing the [TL/NS] key, execute the selected item.If the [CL] key is pressed during the execution of the test, you canexit the test and select a test item.
By selecting “1 BACK LIGHT” and then pressing the [TL/NS] key,the back light can be turned ON/OFF.
By selecting “2 CONTRAST” and using the [ 2 ] / [ 4 ] key, the con-trast value can be changed within the range of 0 to 63 (0x00 to0x3F).
3) By selecting “EXIT” and pressing the [TL/NS] key, this test ends withOK.
By pressing any key other than the [TL/NS] key, [ 2 ] or [ 4 ]key,this test ends with NG.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
6-2. PATTERN DISPLAY1) The following patterns are displayed.
2) By pressing a key, it goes on to the next pattern.
3) By pressing the [TL/NS] key at the last screen, this test ends withOK.By pressing any key other than the [TL/NS] key, this test ends withthe result of NG.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
BACK LIGHT&CONTRASTLCD
PATTERN DISPLAYEXIT
LCD screen
BACK LIGHT&CONTRAST1 BACK LIGHT2 CONTRAST XXEXIT(TL:OK)
LCD screen when finish
BACK LIGHT&CONTRAST NG
Printout (when the test result is NG.)
BACK LIGHT&CONTRAST OK
Printout (when the test result is OK.)
Grid 1 pattern
Grid pattern
Reversed H pattern
H pattern
Full black
Box display- one black dot of outer frame
Full white
LCD screen
Grid 2 pattern (Reversed display of Grid pattern 1)
Termination screen
PATTERN DISPLAY TL:OK,OTHER:NG
Printout (when the test result is NG.)
Printout (when the test result is OK.)
PATTERN DISPLAY NG
PATTERN DISPLAY OK
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 33 –
7. A/D
The status of A/D input is displayed in real time at an interval of 1 sec-ond.If the values of HT1, HV and BBAT are within the range shown below, itprints out with OK.
HT1: HEAD TEMPERATURE 1 1.10 ~ 2.50V
HV: HEAD VOLTAGE1 8.25 ~ 8.75V
BBAT: BACKUP BATTERY VOLTAGE 2.00 ~ 3.40V
By pressing the [TL/NS] key, this test exits.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
8. CLOCK
The date and time are read out from the real time clock (RTC).The date and time are displayed and printed out.By pressing the [TL/NS] key, this test ends with OK.By pressing any key other than the [TL/NS] key, this test ends with NG.By pressing the [0] key, all the values of day, month, year, hour, minuteand second are reset.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
9. DRAWER
This test opens the Drawer.
1) Change the selected item, which is displayed in reversed charac-ters, with the [ 2 ] / [ 4 ] key.
2) When “CH1” is selected, the drawer CH1 opens by pressing the[TL/NS] key. When “EXIT” is selected, the test operator should press either keyaccording to the test result of OK or NG.
3) By pressing the [TL/NS] key, this test ends with OK.By pressing any key other than the[TL/NS] key, [ 2 ] / [ 4 ] key, thistest ends with NG.
4) This test terminates by selecting “EXIT.”
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
A/D HT1 X.XXVHV X.XXV,BBAT X.XXV TL KEY:EXIT
XE-A207/A217LCD display
A/D HT1 X.XXV,HT2 X.XXVHV X.XXV,BBAT X.XXV TL KEY:EXIT
XE-A307
Printout (when the test result is NG.)
A/D NG HT1 X.XXV HV X.XXV BBAT X.XXV
XE-A207/A217
A/D NG HT1 X.XXV HT2 X.XXV HV X.XXV BBAT X.XXV
XE-A307
Printout (when the test result is OK.)
A/D OK HT1 X.XXV HV X.XXV BBAT X.XXV
XE-A207/A217
A/D OK HT1 X.XXV HT2 X.XXV HV X.XXV BBAT X.XXV
XE-A307
XX/XX/XX (dd/mm/yy) (day / month / year)(hour / minute / second)XX:XX:XX
TL:OK,OTHER:NG
CLOCK
LCD display
Printout (when the test result is NG.)
CLOCK NG XX/XX/XX (dd/mm/yy) XX:XX:XX
Printout (when the test result is OK.)
CLOCK OK XX/XX/XX (dd/mm/yy) XX:XX:XX
LCD screen
DRAWERCH1EXITTL:OK,OTHER:NG
Printout (when the test result is NG.)
DRAWER CH1 NG
DRAWER CH1 OK
Printout (when the test result is OK.)
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 34 –
10. RS232C
The RS232C loopback test is performed.
1) Connect the DSUB9pin loopback connector.
2) Select the test item with the [ 2 ] / [ 4 ] key.
3) Select “NORMAL.”
4) Conduct the test by pressing the [TL/NS] key.
5) Select “EXIT” to end the test.
• Below is shown the connection diagram of the loopback connector tobe used for RS232C check.
10-1. NORMAL
(1) Test Items
<Check of Control Signals>
It performs the Read and Check of the above input.
<Check of Data Transfer>
The transfer of 256 bytes loop back data of 00H to 0FFH is conducted.
A found error is displayed.Press the [TL/NS] key to end the test.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
RS232C CH1EXIT
LCD display
LCD display
RS232C CH1 NORMAL5V SUPPLYEXIT
123456789
DCDRxDTxDDTRGNDDSRRTSCTSRI
FG
FG
Output Input
DTRn RTSn DSRn RIn DCDn CTSn
OFF OFF OFF OFF OFF OFF
OFF ON OFF OFF ON ON
ON OFF ON ON OFF OFF
ON ON ON ON ON ON
No. Display
1 DTR-DSR
2 DTR-RI
3 RTS-DCD
4 RTS-CTS
5 RI INT
6 DCD INT
7 CTS INT
8 TXEMP
9 TXEMP INT
10 TXRDY
11 TXRDY INT
12 RCVRDY
13 RCVRDY INT
14 SD-RD(DATA)
15 SD-RD(FRAME)
OK
LCD display (when the test result is NG.)
RS232 CH1NGDTR-DSR,DTR-RI,RTS-DCD,RTS-CTS
LCD display (when the test result is OK.)
RS232 CH1
Printout (when the test result is NG.)
RS232C CH1 NG---ERROR NO.
Printout (when the test result is OK.)
RS232C CH1 OK
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 35 –
10-2. 5V SUPPLY
(1) Test Items<Check of Control Signals>
It performs the Read and Check of the above input.
<Check of Data Transfer>
The transfer of 256 bytes loop back data of 00H to 0FFH is conducted.
A found error is displayed.Press the [TL/NS] key to end the test.
When LED turns on, the test operator should press either key accordingto the test result of ON or OFF.By pressing the [TL/NS] key, this test ends with OK.
Caution:
• To have printout of test results, as XE-A307 has 2 sheets for theprinter, be sure to use both printers to print it out.
• When conducting the PWB inspection for XE-A307V, swith SP3 of thePWB to 5V power supply.
11. PRINTER
The unit displays and prints out as shown below.
By pressing the [TL/NS] key, this test ends with OK.By pressing any key other than the [TL/NS] key, the test ends with NG.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
12. ROM
Check whether the checksum of 000000h to 1FFFFFh is correct.By pressing the [TL/NS] key, this ends.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
Output Input
DTRn RTSn DSRn DCDn CTSn
OFF OFF OFF OFF OFF
OFF ON OFF ON ON
ON OFF ON OFF OFF
ON ON ON ON ON
No. Display
1 DTR-DSR
2 RTS-DCD
3 RTS-CTS
4 DCD INT
5 CTS INT
6 TXEMP
7 TXEMP INT
8 TXRDY
9 TXRDY INT
10 RCVRDY
11 RCVRDY INT
12 SD-RD(DATA)
13 SD-RD(FRAME)
LCD display (when the test result is NG.)
RS232 CH1SIGNAL CHECK:NGDTR-DSR,RTS-DCDRTS-CTS
LCD display (when the test result is OK.)
RS232 CH1SIGNAL CHECK:OKLED ON?TL:ON, OTHER:OFF
Printout (when SIGNAL CHECK is NG.)
RS232C CH1 NG---ERROR NO.
Printout (when SIGNAL CHECK is OK, LED is OFF.)
RS232C CH1 NG
Printout (when SIGNAL CHECK is OK, LED is ON.)
RS232C CH1 OK
LCD screen
PRINTER
TL:OK,OTHER:NG
Printout
/////////// ------- ///////////////////// ------- //////////
/////////// ------- //////////
Print 30 columns and 6 lines of "/."
LCD display (when the test result is NG.)
ROMVersion xxxx Checksum xxxx NG TL KEY:EXIT
Printout (when the test result is NG.)
ROM Version & CHECKSUM Version xxxx Checksum xxxx NG
ROM
LCD display (when the test result is NG.)
Version xxxxChecksum xxxx OKTL KEY:EXIT
Printout (when the test result is OK.)
ROM Version & CHECKSUMVersion xxxxChecksum xxxx OK
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 36 –
13. RAM
The Write & Verify of the whole RAM area is conducted.Change the written data for each address as shown below.
After the test result is displayed (printed out), press the [TL/NS] key toterminate.
Caution: To have printout of test results, as XE-A307 has 2 sheets forthe printer, be sure to use both printers to print it out.
Address Written data800000h 80FFFFh
800000h 80FFFFh
810000h 81FFFFh
810000h 81FFFFh
|(The rest is omitted)
870000h 87FFFFh
55h write,verify
AAh write,verify
55h write,verify
AAh write,verify
|(The rest is omitted)
55h write,verify
AAh write,verify 870000h 87FFFFh
LCD display (when the test result is NG.)
RAM WRITE&VERIFY NGTL KEY:EXIT
LCD display (when the test result is OK.)
RAM WRITE&VERIFYOKTL KEY:EXIT
Printout (when the test result is NG.)
RAM NG
Printout (when the test result is OK.)
RAM OK
XE-A207/A217/A307 DIAGNOSTIC PROGRAM DESCRIPTION
– 37 –
CHAPTER 7. PWB LAYOUT
(1) MAIN PWB<TOP SIDE>
<BOTTOM SIDE>
XE-A207/A217/A307 PWB LAYOUT
– 38 –
(2) PRINTER I/F PWB
<TOP SIDE>
<BOTTOM SIDE>
(3) KEY I/F PWB
<TOP SIDE>
<BOTTOM SIDE>
XE-A207/A217/A307 PWB LAYOUT
– 39 –
CHAPTER 8. CONNECTOR PIN LAYOUT
(1) MAIN PWB
CN8
5045-03A
123
LCD_TXD1LCD_SCK1
VCC3
VLED-VCC5
C2040.1uF/50V(1608)
10022HS-12C
CN3
LED+12
NC11
LED-10
VSS9
VSS8
SCL7
SI6
A05
CS#4
RST3
VCC32
VCC31
C203
0.1uF/10V
VBAT
R215
10
CN16
5267-02A-X
11
22
C1380.1uF/50V(1608)
PSTRB02PSTRB01PSTRB00
PSTRB05PSTRB04PSTRB03
PHK0
PLAT0#
PDAT
MT0BMT0/B
PCLK
MT0AMT0/A
PHE0
HOSEN0
TP65
V_HEAD
VCC3
V_PSEN
VCC3
VCC3
CN5
10022HS-30C
302928
2726
2524
2322
2120
191817
16
1514
131211
109
87
65
4321
R130
30K/F
R130
30K/F
C148470pF
C89
470pF
C89
470pF
R244 22KR322(N.M)100
R123 220
R125 47K
CN9
YW396-02V
11
22
F4SRT_2.5A
RI0_SP
RTS0
DCD0
DTR0
TX_0CTS0
RX_0DSR0
CN712511HS-11SS-K
RI_19
CTS_16
RTS_14
TX_15
DTR_17
RX_13
DSR_12
DCD_11
GND11
RI_18
GND10
KR7#
KR4#
KR6#KR5#
KR1#KR0#
KR2#KR3#
7SEG_e
7SEG_dp7SEG_g7SEG_f
7SEG_c7SEG_b
7SEG_d
7SEG_a
KS1KS0
KS2KS3
KEYCHK
KR8#KR9#
VCC5
R90 33
C620.1uF/50V(1608)
CN4
10022HS-30C
302928272625242322212019181716151413121110987654321
C80
100pF
+
C4933uF/10V_MVL(5x5.7)
+
12
XE-A207/A217/A307 CONNECTOR PIN LAYOUT
– 40 –
(2) KEY I/F PWB
KR9
KR8
KR0
KR1
KR2
KR3
KR4
KR6
KR7
KR5
CN19FCZ254-10S
1
2
3
4
5
6
7
8
9
10
v5p_STB8#
v5p_STB7#
v5p_STB6#
v5p_STB11#
v5p_STB13#
v5p_STB12#
v5p_STB5#
v5p_STB4#
v5p_STB3#
v5p_STB2#
v5p_STB1#
v5p_STB9#
v5p_STB10#
D63 KDS4148UD63 KDS4148U
AC
D64 KDS4148UD64 KDS4148UAC
D59 KDS4148UD59 KDS4148UAC
D67 (_FLAT)KDS4148UD67 (_FLAT)KDS4148U
AC
D62 KDS4148UD62 KDS4148UAC
D58 KDS4148UD58 KDS4148UAC
D61 KDS4148UD61 KDS4148UAC
CN18-2
1
2
3
4
5
6
7
8
9
10
11
12
13
D69 (_FLAT)KDS4148UD69 (_FLAT)KDS4148UAC
D57 KDS4148UD57 KDS4148UAC
D65 (_FLAT)KDS4148UD65 (_FLAT)KDS4148U
AC
D60 KDS4148UD60 KDS4148UAC
D66 (_FLAT)KDS4148UD66 (_FLAT)KDS4148U
AC
CN18-1
FCZ254-13S
FCZ254-08S
D68 (_FLAT)KDS4148UD68 (_FLAT)KDS4148U
AC
K_KS1
K_KS3
K_KS0
K_KS2
a
cdef
dpg
b
KR0
KR7KR6KR5KR4KR3KR2KR1
CHK_KEY
KR8KR9
VCC5(5.0V) signal
+
C217
100uF/16V_MVL(6.3x7.7)
+
12
10022HS-30C
CN17
302928272625242322212019181716151413121110987654321
G4
B#
G1
G5
E#F#
D#
A#
G6
G3
G#
C#
G2
DP#
G7-CHK
CN22
FCZ100E-15SS-K
151413121110987654321
For Singapore
For Singapore
XE-A207/A217/A307 CONNECTOR PIN LAYOUT
– 41 –
SHARP CORPORATIONBusiness Solutions Promotion GroupCS Promotion DepartmentYamatokoriyama, Nara 639-1186, Japan
2011 July Printed in Japan
Trademark acknowledgements
COPYRIGHT 2011 BY SHARP CORPORATIONAll rights reserved.Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.
Microsoft® Windows® operating system is a trademark or copyright of MicrosoftCorporation in the U.S.A. and other countries.
Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000,Windows® XP, Windows® Vista, Windows® 2000 Server, Windows® Server 2003and Internet Explorer® are trademarks or copyrights of Microsoft Corporation in the U.S.A. and other countries.
IBM and PC/AT are trademarks of International Business Machines Corporation.
Acrobat® Reader Copyright® 1987-2002 Adobe Systems Incorporated. All rightsreserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarksof Adobe Systems Incorporated.
All other trademarks and copyrights are the property of their respective owners.