Audio Visual Training

transcript

AUDIO VISUAL TRAININGAUDIO VISUAL TRAININGVaughn Eames-Lite ClassVaughn Eames-Lite Class

LITE CLASSROOM EQUIPMENTLite Class

TURNING ON A/V SYSTEM Lite Class

Press the “POWER” button located on the top of the

control panel and the projector will begin turning

PROJECTING A LAPTOPLite Class

Once the projector is on, press the “SOURCE” button until the projector displays

“Input A” on the top right side of the screen.

If you don’t have a “SOURCE” button on your control panel, press the “COMP” button on the control panel to display

your laptop.

Plug in your laptop to the *VGA cord located in the grey

If you have a Mac laptop use your VGA adapter.

*Do not bend or yank on the VGA Cord as this will cause it to break.

If your PC laptop does not project onto the screen, press and hold the “FN” key

located on the bottom left hand side of your laptop’s keyboard.

While holding the “FN” key press the

“F8” key, if you have a Dell laptop.

“ F4” key, if you have an HP laptop.or

“F5” key, if you have a Toshiba/Sony laptop.

Then release them both at the same time.

If your Mac laptop does not display go into your System Preferences and double click “Displays”.

When Display window opens, click “Detect Displays”.

Then click on the “Arrangements” tab.

After Arrangement Tab opens check the box in the bottom left hand corner that says “Mirror Displays”.

To adjust the volume coming from your *computer press the “VOL ” and “VOL ” buttons on the bottom of the control

panel.

*Please note, volume must also be turned up on your laptop to receive sound.

PROJECTING A DVDLite Class

Plug your*borrowed DVD/VCR combo player into an outlet and

press the “POWER” button on the bottom left hand corner of

the player.

*Loaner DVD/VCR players are available for pick up at Audio Visual Technology.

Plug the red, yellow, and white cables (composite cables) into

the back of the DVD player where it says “Line Out”.

Plug the other end of the composite cables into the

corresponding colored jacks on the wall box.

• Press the Eject button next to the DVD player to open it.

• Place DVD in player with label up.

• Push the Eject button again to close and load the DVD player.

Press the “Source” button on the control panel until the

projector shows “VIDEO” in the top right hand corner of the

screen.

If there is no “Source” button press the “Video” button to

display DVD.

There are 2 ways to control your DVD:

1. Use control buttons located on the DVD player itself.

2.Use the remote control that came with the DVD player.

PLAYING A DVDLite Class

To adjust the volume coming from the DVD press the

“VOL +” and “VOL –” buttons on the bottom of the control panel.

PLAYING A DVDLite Class

To stop the DVD press the STOP button located on the bottom left hand corner of the DVD

player.

Press the “Eject” button to retrieve your DVD.

PROJECTING A VHSLite Class

Plug your*borrowed DVD/VCR combo player into an outlet and

press the “POWER” button on the bottom left hand corner of

the player.

*Loaner DVD/VCR players are available for pick up at Audio Visual Technology.

Plug the red, yellow, and white cables (composite cables) into

the back of the VHS player where it says “Line Out”.

Plug the other end of the composite cables into the

corresponding colored jacks on the wall box.

Put your VHS tape into the slot on the right hand side of the

player.

Press the “Source” button on the control panel until the

projector displays “Video” in the top right hand corner of the

screen to have the projector display the VHS tape.

If there is no “Source” button press the “Video” button on the control panel to display the VHS

There are 2 ways to control your VHS:

1. Use control buttons located on the VHS player itself.

2.Use the remote control that came with the VHS player.

To adjust the volume coming from the VHS press the

“VOL +” and “VOL –” buttons on the control panel.

To stop the VHS, press the STOP button located on the bottom left hand corner of the VCR.

Press the “Eject” button to retrieve your VHS.

TURNING OFF THE A/V SYSTEM Lite Class

To turn off the A/V System press the “Power” button

located on the control panel twice.

TURNING OFF THE A/V SYSTEM Lite Class

Turn off the Laptop or DVD/VCR you are using, disconnect them,

and you have completed shutting down the A/V system.

AUDIO VISUAL CONTACT INFOLite Class

• Office Phone: Ext. 76120

• Office Email: avt@kean.edu

• Office Location: Technology Building Room 110

• Office Website: http://www.kean.edu/~avt/

This presentation was created by Katherine Roba kroba@kean.edu ~ 908 737 6122

Audio Visual Training

Documents