Post on 04-Aug-2020
transcript
STYLE No. FRLS10
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Lever Handles
STYLE No. FRLS01
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 1 OF 5 | UPDATED ON 4.24.2019PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
IMPORTANT:
To ensure this product is installed properly, you must read andfollow these guidelines.
The owner/user of this product must keep this information forfuture reference.
This product must be installed by a professional licensedcontractor.
Be sure your installation conforms to federal state, and local codes.In the State of Massachusetts, all installations must comply with therules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required forproper installation. Product is sold partially assembled but shownfully disassembled for illustrative and service purposes only.
Use only a strap wrench or protected/smooth-jaw wrench on anyfinished surface.
The use of certain plumber’s putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support at1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for availablereplacement parts.
TECHNICAL DETAILS:
DETAIL SPECIFICATION
DECK THICKNESS 1/4” [6mm] MIN
1-5/8” [41mm] MAX
DRAIN DEPTH 1-3/8” [35mm] MIN 1-3/4” [45mm] MAX
DRAIN HOLE DIAMETER Ø1-3/4” [44mm]
DRAIN STYLE POP-UP
FITTINGS HOLE DIAMETER Ø1-3/8” [35mm]
HANDLE SPREAD 8" [203mm] MIN
12” [305mm] MAX
HANDLE TURN ANGLE QUARTER TURN
INLET CONNECTION 1/2" MALE WITH SUPPLY NUT
SPOUT REACH 5-3/8” [137mm]
WATER PRESSURE RANGE 20psi [1.5 bar] MIN
85psi [6.0 bar] MAX
WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
STYLE No. FRLS10
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Lever Handles
STYLE No. FRLS01
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 2 OF 5 | UPDATED ON 4.24.2019PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
RUBBERWASHER
TEE
CAP
RUBBERWASHER
TEE
CAPSCREW[DO NOT REMOVE]
PACKINGNUT[LOOSEN]
SPOUTRUBBER WASHER[DO NOT REMOVE]
SHANK
RUBBERWASHER
PLASTICWASHER
NUT
SPOUTRUBBER WASHER[DO NOT REMOVE]
SHANK
RUBBERWASHER
PLASTICWASHER
NUT
NUT
PLASTIC WASHER
RUBBER WASHER
RUBBER WASHER *
SPOUT
NUT
PLASTIC WASHER
RUBBER WASHER
RUBBER WASHER *
SPOUT
* If desired, a beadof caulk or a clear siliconemay be applied where theSPOUT contacts themounting surface.
1. Loosen but do NOT remove the SCREW on theCAP then remove the CAP. Loosen but do NOTremove the PACKING NUT at the base of the TEEthen remove the TEE and RUBBER WASHER fromthe SHANK.
2. Unthread and remove the NUT and lower deckWASHERS from the SHANK.
NOTE: Do NOT remove the RUBBER WASHERbeneath the ESCUTCHEON.
3. Insert the SHANK through the hole on the mounting surface making sure the RUBBER WASHER is beneath the SPOUT then reattach the WASHERS and securely tighten the NUT.
O-RING
TEE1/2" MALE THREADS
METAL WASHER
PACKING NUT
O-RING
TEE1/2" MALE THREADS
METAL WASHER
PACKING NUT
4. Remove the PACKING NUT, METAL WSAHER andO-RING from the TEE to prevent the GUIDE TUBEin the SPOUT from damaging the O-RING.
NUT
GUIDE TUBE
SPOUT SHANK
SPOUT
NUT
GUIDE TUBE
SPOUT SHANK
SPOUT
RUBBER WASHER
5. Thread and securely tighten the TEE onto theSHANK making sure to use the RUBBER WASHERprovided.
SPOUT
LIFT ROD
KNOB
SPOUT
LIFT ROD
KNOB
O-RING
6. Insert the LIFT ROD into the top of the SPOUT making sure the O-RING is beneath the KNOB.
STYLE No. FRLS10
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Lever Handles
STYLE No. FRLS01
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 3 OF 5 | UPDATED ON 4.24.2019PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
METAL WASHER
GUIDE TUBE
O-RING
PACKING NUT
METAL WASHER
GUIDE TUBE
O-RING
PACKING NUT
CAP
GUIDE TUBE
CAPSCREW
KNURLED NUT
7. Insert the O-RING and METAL WASHER into thebase of the TEE then insert and securely tighten thePACKING NUT.
8. Slide the CAP up the LIFT ROD and onto the GUIDETUBE then securely tighten the SCREW.
NOTE: Use the KNURLED NUT to adjust the tensionon the LIFT ROD. Do NOT over tighten the NUT.
9. Remove the INDICE then unthread and remove the SCREW, METAL WASHER, HANDLE and STEM.
SIDEBODY
RUBBER WASHER,PLASTIC WASHER,NUT
O-RING
TRIMCONNECTOR
RUBBERWASHER
GLAND COVER[INTERNAL O-RING]
NUT
10. Unthread and remove the GLAND COVER, RUBBER WASHER, TRIM CONNECTOR and O-RING from the SIDEBODY then fully thread the NUTdown the SIDEBODY.
NOTE: Do NOT remove the lower deck WASHERS.
SIDEBODY
MOUNTING SURFACE
O-RING
TRIM CONNECTOR
11. Using the O-RING provided, thread the TRIM CONNECTOR back onto the SIDEBODY then let itrest on the mounting surface.
RUBBER WASHER,PLASTIC WASHER
NUT[HAND TIGHTEN]
12. Hand-tighten the NUT against the underside of the mounting surface.
NOTE: Do NOT over-tighten the NUT to allow for the proper HANDLE alignment during the HANDLE installation.
HANDLE STEM
HANDLE
MEATL WASHER
SCREW
INDICE[EXTERNAL O-RING]
HANDLE STEM
HANDLE
MEATL WASHER
SCREW
INDICE[EXTERNAL O-RING]
STYLE No. FRLS10
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Lever Handles
STYLE No. FRLS01
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 4 OF 5 | UPDATED ON 4.24.2019PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
s
CARTRIDGE
RUBBER WASHER
GLAND COVER †[INTERNAL O-RING]
CARTRIDGE
RUBBER WASHER
GLAND COVER †[INTERNAL O-RING]
† A RUBBER WASHER forthe GLAND COVER isprovided. If desired, a beadof caulk or a clear siliconemay be applied where theGLAND COVER contacts themounting surface.
HANDLE STEM
HANDLE
MEATL WASHER
SCREW INDICE[EXTERNAL O-RING]
HANDLE STEM
HANDLE
MEATL WASHER
SCREW INDICE[EXTERNAL O-RING]
NUT[SECURELY TIGHTEN]
SCREW
METALWASHER
HANDLE[2ND]
INDICE[EXTERNAL O-RING]
SCREW
METALWASHER
HANDLE[2ND]
INDICE[EXTERNAL O-RING]
13. Using the RUBBER WASHER provided, thread theGLAND COVER back onto the CARTRIDGE until it contacts the mounting surface.
14. Fully insert the HANDLE STEM into the GLANDCOVER and place the HANDLE onto the STEM thenthread and securely tighten the SCREW. Ensure theHANDLE is in the desired orientation then securely tighten the NUT and install the INDICE.
15. Repeat Steps 9 through 14 to install the second (2ND) HANDLE.
SUPPLY HOSE
TEE
SUPPLY HOSE[2ND]
SUPPLY HOSE
TEE
SUPPLY HOSE[2ND]
16. Connect the SIDEBODIES to the TEE using theSUPPLY HOSES provided. Securely tighten theHOSES and ensure they are not pinched/kinked.
NUT
TAILPIECE
RUBBER WASHER
LOWER DRAINBODY
NUT
TAILPIECE
RUBBER WASHER
LOWER DRAINBODY
KNURLEDNUT
LOWER DRAINBODY
LOWER DRAINGASKET
FOAM WASHER[DISCARD]
DRAIN FLANGE
DRAIN STOPPER
KNURLEDNUT
LOWER DRAINBODY
LOWER DRAINGASKET
FOAM WASHER[DISCARD]
DRAIN FLANGE
DRAIN STOPPER
17. Unthread and remove the NUT, TAILPIECE, and theRUBBER WASHER from the LOWER DRAIN BODY.
18. Unthread and remove the LOWER DRAIN BODY, LOWER DRAIN GASKET, and the DRAIN STOPPER from the DRAIN FLANGE. Unthread and remove the KNURLED NUT from the LOWER DRAIN BODY.
NOTE: Do NOT discard the BALL SOCKET.
STYLE No. FRLS10
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Lever Handles
STYLE No. FRLS01
Foro Low Profile Three Hole Deck Mounted Lavatory Faucet with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 5 OF 5 | UPDATED ON 4.24.2019PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
21. Making sure the BALL SOCKET is in place, insert the PIVOT ROD into the DRAIN BODY and securely tighten the NUT then insert the STOPPER into the FLANGE making sure the SCREW rests on top of the PIVOT ROD. Adjust the SCREW if needed.
LOWER DRAINBODY
LOWER DRAINGASKET
DRAIN FLANGE
LOWER DRAINBODY
LOWER DRAINGASKET
DRAIN FLANGE
FACINGTOWARDS
SPOUT
NUT
TAIL PIECE
RUBBER WASHER
LOWER DRAINBODY
NUT
TAIL PIECE
RUBBER WASHER
LOWER DRAINBODY
PIVOTROD
SCREW
JOINT
KNURLED NUT
BALLSOCKET
LOWERDRAINBODY
DRAIN STOPPER
PIVOTROD
SCREW
JOINT
KNURLED NUT
BALLSOCKET
LOWERDRAINBODY
DRAIN STOPPER
19. Set the DRAIN FLANGE into the lavatory (soldseparately) using putty or a clear silicone andattach the LOWER DRAIN GASKET then securely tighten the LOWER DRAIN BODY onto theFLANGE.
20. Re-attach the TAILPIECE then securely tightenthe NUT onto the LOWER DRAIN BODY makingsure to include the RUBBER WASHER provided.
LIFT ROD[FIELD
CUTTABLE]
PIVOT ROD[FIELD CUTTABLE]
LINKAGE
22. Connect the LIFT ROD to the PIVOT ROD using the LINKAGE provided.
NOTE: Both RODS may be field cut.
SUPPLY TUBE[NOT SUPPLIED]
SUPPLY NUT[SUPPLIED]
SIDEBODY
SUPPLY VALVE[NOT SUPPLIED]
P-TRAP[NOTSUPPLIED]
TAIL PIECE
SUPPLY TUBE[NOT SUPPLIED]
SUPPLY NUT[SUPPLIED]
SIDEBODY
SUPPLY VALVE[NOT SUPPLIED]
P-TRAP[NOTSUPPLIED]
TAIL PIECE
23. Make final P-TRAP (sold separately) and SUPPLYVALVE (sold separately) connections.
24. Remove the AERATOR, turn on the water to flush out the supply lines, inspect all connections for leaks, and close the DRAIN to ensure it functions properly. Turn off and drain the water then reinstall the AERATOR.
AERATORKEY
AERATOR
3. CLOSE DRAIN
AERATORKEY
AERATOR
1. REMOVE AERATOR2. TURN ON WATER ANDOPERATE HANDLES
KNOB
LIFT ROD