Good Afternoon

Liquid Filtration Liquid Filtration

. Types of Filtration

Process

IndustrialPower Generation (Rotary Equipment)

Gas Filtration, Separation, Coalescing

Liquid/Liquid Separation

.Process FiltrationProcess Filtration

Own Style of Vessel and Element

. Swing Bolts and legs

. Elements are normally 2.5” OD x 1” ID X 10” Long – 40” Long

. Many Sealing Devices

Many Materials of Construction.TeflonPolyethersulfoneNylonRayonPolyester

Polypropylene

MicroglassCottonMetal TubesGlass (Baked and Unbaked)

Terminology of Process Vessel. InternalsTop Seat Plate Assembly – Cap and Spring as one pieceTube GuideUniversal Seat Cup

. Universal Seat Cup will Accommodate

222 “O” Ring single closed end

Double Open EndDouble Open End w/ Gaskets

Standard Open End W/Spring

222 “O” Ring with Fin End

226 Closed End

Extended Core (Open or Poly Spring, Closed End

Centercore for Process Elements 2.5” OD x Lengths 10” 20” 30” & 40”

Materials: Polypropylene

Tin Plated

304 SS, 316 SS

Poly Spring w/open end

Bayonet End (Millipore Style)Element Extender (plugs into seat

cup)

“222” O Ring End (plugs into seat cup)

Interlock Cap, SOE

“226” Single O Ring, (plugs into seat cup)

Standard Closed End Cap

Standard End Cap when Gasket is needed

Process Filter Vessel

Universal Seat CupAccepts:

Double Open End

222 “O” Ring SOE

226 “0” Ring SOE

Extended center core

Example of 222 “O” ring and

Universal Seat Cup together

Extender that fits into the Separator Plate

Typical Process Vessel

and Internal Set up

Industrial Filtration & Power Generation . Own Style of Vessel and Element. Straight Through Bolts . Elements are normally 6” OD x 2.5” ID X 18” Long – 44” Long

Internal set up versus Process – Very Simple.. Materials of Construction

Cellulose (Paper)

Polyester

Microglass

Pleated Metal

ASME Code Simplex & Duplex

Standard Polyester Pleated Media

Sizes3” OD x 1 ¼” ID x 10” long6” OD x 2 5/8” ID x 18” Long6” OD x 2 5/8” ID x 36” long6” OD x 39” ID x 39” long

3 uM

1 uM

6 uM

12 uM

25 uM

1600

800

400

200

Beta R

atio

2 4 6 8 10 12 14 16 18 20 22 24 26 MIcron

Metal Strainers 2200 Series Elements Available in Metal

Micron ranges from 5 micron to 100 MicronHelps with Temperature and Compatibility

Interchangeability with “2200”, ‘C’, ‘S’, and “V” Series elements

Versatility of Applications

Chemicals Electronic Food & Beverage Magnetic Media Pharmaceuticals Cosmetics Medical Photographic

Animal Oils Concentrated Alkalies Dilute Acids & Alkalies Mineral Acids Organic Acids & Solvents Oxidizing Agents Petroleum Oils Photo Solutions Potable Liquids Vegetable Oils Water Prefilter for Membranes Amines

Potable LiquidsOrganic Solvents LubricantsProcess Water Cooking OilsPhotoprocessing AminesChemical Process R.O. PrefiltrationDisposal Well

Photographics Plating Solutions High Technology Coatings Food & Beverages Membrane Prefiltration DI Water Chemical Processing

Power Generation – Rotating Equipment

Compressors, Gas Turbines, Steam Turbines, Generators, Couplings

Liquid – Lube – Fuel - Water

Natural Gas

2710E1 NFS Part Number

2710E1VO NFS Part Number

2300AJ NFS Part Number

P718-0030-SH-1-7 Old NFS Part

S186-0030-F-1 HYCOA Part Number

2200A4 NFS Part Number

P426-0250-PC-1-7 Old Part Number

V264-0250-F-1 HYCOA Part Number

HYG15129E Air Atomizing Element

Two Sizes for GE Part

363A4330P002 & P003

8” OD x 20” L and 11” OD x 21” L

Polypropylene Process

Element 2600M6 NFS Part NumberM330-0010-SS-1-0 Old Number

Sizing based on actual applications:

Design Flow Rate: 100 USGPM of Heat Transfer FluidDesign Temperature: -20o F to 650o FDesign Pressure: 125 PSIASME Code and Stamp Construction in Carbon Steel .06” Corrosion Allowance 2” Butt Weld connections 3/4” FNPT vent and drain (Plugged)Nickel plated bolting for corrosion resistance at high temperatureHigh temperature 304 SS spiral wound closure gasket per EES VED1003AElement Rated 98% @ 5 uMModified Silicone PaintElements:Data Sheets & Assembly DrawingWPS/PQR/Weld MapASME Code CalcsNDE Testing and examiner qualificationsMaterial Test ReportsNameplate DetailU-1 Form

Recommend and size a vessel

Power Generation Application:

Design Flow Rate: 2,200 GPMDesign Pressure: 200 PSIGDesign Temperature: -20 to 250 deg FCorrosion Allowance: 0.0625”Fluid: ISO 32 Light OilNormal Flow Rate: 0 to 2,000 GPMViscosity: 60 to 800 SSU (temp dependent)Operating Pressure: 200 PSIGOperating Temperature: 20 to 250 deg FMax Pressure Drop: 5 PSID25 Micron

Steam Turbine Lube Oil

General Industrial Application:Hydraulic Oil

Design Flow Rate: 100 GPM Of ISO VG 46 OilDesign Temperature: -20o F to 200o FDesign Pressure: 1000 PSINon-Code Carbon Steel1000 PSI Design @ -20 to 1750 F2” in/out Connections3/4” NPT vent and drain connections25 Micron 99%Duplex Design

Process Design: Salt Water

(2) salt water filters, carbon steel with internal coating is ok.Flow : 250 GPMLine Pressure 100 psigDP: 2psiMicron: 40

Vessel Stub-up

Spring

Standard Element

Cardboard Box

Power Generation Element, Lube Oil, Liquid Fuel Oil for Gas Turbines, Bio-Diesel and Ethanol fuels as a Standard.

2200A2, A3, A4

V264-0010, 0060, 0120, 250

V394, V396

Gas Filtration, Separation, Coalescing

Liquid/Liquid Separation

National Filtration Systems, Inc.

Incoming Request for Vessels or Systems

Dwight Coy

Aftermarket Element Quotes and OrdersIncludes:

Gaskets, Shoe Kits for HYCOA, Process Elements, Mahle, Power Generation and General Industrial Elements, Set up new accounts.

Tom Tokar