Pemasangan Sistem Pemipaan Air Bersih

Post on 26-Mar-2015

210 views 4 download

transcript

ENGINEERING PLUMBING AND SANITATION

Application of Plumbing System Of Clean Water

System of Clean Water

Purpose Of Common Instructional :

1. After this Lesson solvent and understands in explaining system division of clean water .

Teknologi dan Rekayasa

Purpose Of Special Instructional Student can mention :

1. Direct joint system 2. Indirect joint system 3. Advantage and disadvantage of

one of system

Teknologi dan Rekayasa

Teknologi dan Rekayasa

Installation of Clean Water Pipe

To get safe installation there are some thing that need to be paid attention :

1. Material is not corrosion easy to

2. Pipe through wall must be given canopy

3. Applycation of pipe must be diametrical

Teknologi dan Rekayasa

4.Utilizes fitting for transformation of direction and transformation of diameter

5.Exactly in determination of pipe diameter

6.For vertical pipe labored straight to the above of from basis

7.Every floor gives one crane stops8.After meter water is attached [by]

crane which can prevent reverse flow

Teknologi dan Rekayasa

Example : Installation Scheme of Pipe in building

1. Principal pipe2. Housing joint3. Meter water4. Distributor pipe5. Supply pipe of clean water6. Vertical pipe7. Branch pipe for equipments sanitary

Correct installation :

Teknologi dan Rekayasa

In important installation again was all valves or crane attached at one particular installation didn't cause or can generate reverse flow and exploitation to return if there are

transformation of water pressure in installation.

1. Direct joint system

This system especially applied for low and small housing

And Example :

a. Shut off valve in plot of land

b. Shut off valve below(under road street)

physical plant.

Teknologi dan Rekayasa

Teknologi dan Rekayasa

a. Shut off valve in plot of land

Teknologi dan Rekayasa

b. Shut off valve below(under road street) physical plant.

2. Indirect joint system :

In this system, distribution pipe within doors indirectly is attributed to principal pipe of supply of cleanness water.

Water is accomodated in advance in the tank then is flown / pumped to be distributed in building for requirement of cleanness water would.

Teknologi dan Rekayasa

2.1. Roof tank system :

At this system, water is accomodated in advance in the tank under (attached to low floor of building or below(under ground face), then is pumped to an usual upper tank is attached above roof or above highest floor of building.

Teknologi dan Rekayasa

Teknologi dan Rekayasa

Drawing :System with roof tank

Compress tank system drawing

Teknologi dan Rekayasa

Application of Subterranean Pipe

Purpose Of Common Instructional :

1. After this Lesson solvent student and understands way of applications of pipe in ground.

Teknologi dan Rekayasa

Purpose Of Special Instructional Student can mention :

1. Dig aperture height 2. Way of putting down pipe in dig 3. Detention of pipe from at

dividing valve ( for big diameter ) 4. Pipe test

Teknologi dan Rekayasa

Applications of subterranean pipe

Teknologi dan Rekayasa

4 important factor of Applications subterranean pipe :

1.Dig aperture height

Teknologi dan Rekayasa

2. Situation of Pipe

Teknologi dan Rekayasa

Explanation

A. Situation of Correct pipe because :

Pipe exactly ground anvil.

Easy to checking of joint before landfill with ground

Teknologi dan Rekayasa

B. situation of Not accurate pipe because.

Ground anvil pipe only in each joint

Cannot guarantee lineation of pipe

If there are dividing valve from the top (of), very possibly pipe earns break

Teknologi dan Rekayasa

C. Situation of Pipe that is not true because : Equiamplitude surface of ground scraggly Pipe support above land not

regular Possibility to change / peripatetic

when landfill [by] ground or receives payload from the top monstrous.

Teknologi dan Rekayasa

A.Turns pipe

Teknologi dan Rekayasa

Joint that need to be given retainer :

B. Joint Knie 90

Teknologi dan Rekayasa

C. Tee Joint

Teknologi dan Rekayasa

D.Pipe connection final_

Teknologi dan Rekayasa

4 . Test pipe :

Step of putting down pipe :

a. Ground dug and in dig basis has plane equiamplitude surface.

b. Equiamplitude surface of dig has certain dip

Teknologi dan Rekayasa

c. Given sand as thick 10 cm

d. Pipe is put down, tied on correctness

e. Put down as according to above mentioned drawing.

Teknologi dan Rekayasa

Step of pipe test :

a. In check before hand every joint

b. By the end of pipe network is closed

Teknologi dan Rekayasa

c. At the end of pipe network attributed to pump

d. Depressed until pipe dividing valve permitted

e. Emphasis within 15 second/ 100 m. Pipe length.

Teknologi dan Rekayasa

Pipe test scheme

Teknologi dan Rekayasa

THE END

Teknologi dan Rekayasa