Post on 23-Feb-2018
transcript
7/24/2019 Rainsaver MK5 Data Sheets
1/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-INOX60PC2 - 800400
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 Warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is apower failure.
The RS5-INOX60PC2 Package:
Bianco INOX60PC2 pressure system pump with auto-restartpump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains
Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power andcan be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-INOX60PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and
constant pressure at low ows. Automatic electronic control has
built-in check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-INOX60PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 330W
Current: 2.3 amps
Capacitor: 12 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overloadIngress protection: IP54
Insulation class: F
Power cable length: 1.2 m
Net weight: 9.2 kg
Performance:
Maximum ow: 36 litres per minute (4 taps)
Maximum pressure: 320 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
300 40 500
50
40
30
20
10
Flow (L/min)
Head(m)
2010
BIA-INOX60PC
7/24/2019 Rainsaver MK5 Data Sheets
2/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALLINOX60PC2 - 800408
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart. No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40C
Maximum recommended continuous pump ow: 120 l/mMaximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is a
power failure.
The RS5-INOX60PC2 Package:
Bianco INOX60PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains
Changeover Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved exible hoses
x 2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-INOX60PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and
constant pressure at low ows. Automatic electronic control hasbuilt-in check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-INOX60PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 330W
Current: 2.3 amps
Capacitor: 12 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overloadIngress protection: IP54
Insulation class: F
Power cable length: 1.2 m
Net weight: 9.2 kg
Performance:
Maximum ow: 36 litres per minute (4 taps)
Maximum pressure: 320 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
300 40 500
50
40
30
20
10
Flow (L/min)
Head(m)
2010
BIA-INOX60PC
7/24/2019 Rainsaver MK5 Data Sheets
3/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-MULTI900PC2 - 800401
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-MULTI900PC2 Package:
Bianco MULTI900PC2 pressure system pump with auto-restartpump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power andcan be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-MULTI900PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-MULTI900PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 585W
Current: 3.4 amps
Capacitor: 16 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overloadIngress protection: IP54
Insulation class: F
Power cable length: 1.2 m
Net weight: 11.7 kg
Performance:
Maximum ow: 80 litres per minute (9 taps)
Maximum pressure: 352 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
300 40 50 60 80 900
40
30
20
10
Flow (L/m)
Head(m)
2010 70
BIA-MULTI900PC
7/24/2019 Rainsaver MK5 Data Sheets
4/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALLMULTI900PC2 - 800409
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-MULTI900PC2 Package:
Bianco MULTI900PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved exible hoses
x 2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-MULTI900PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-incheck valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-MULTI900PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 585W
Current: 3.4 amps
Capacitor: 16 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overload
Ingress protection: IP54
Insulation class: F
Power cable length: 1.2 m
Net weight: 11.7 kg
Performance:
Maximum ow: 80 litres per minute (9 taps)
Maximum pressure: 352 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
300 40 50 60 80 900
40
30
20
10
Flow (L/m)
Head(m)
2010 70
BIA-MULTI900PC
7/24/2019 Rainsaver MK5 Data Sheets
5/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-40UP037PC2 - 800402
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-40UP037PC2 Package:
Universal 40UP037PC2 pressure system pump with auto-restartpump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power andcan be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-40UP037PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-40UP037PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 370W
Current: 2.2 amps
Capacitor: 10 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overloadIngress protection: IP55
Insulation class: F
Power cable length: 1.2 m
Net weight: 7.0 kg
Performance:
Maximum ow: 50 litres per minute (5 taps)
Maximum pressure: 370 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
0.6 1.2 1.8 2.4 3 .0 3.6 4.2 4.8 m3/h
l/min
UP-40UP037
0
10
20
30
40
50
60
8070605040302010
Flow
)m(daeH
7/24/2019 Rainsaver MK5 Data Sheets
6/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALL40UP037PC2 - 800410
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-40UP037PC2 Package:
Universal 40UP037PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved exible hoses
x 2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-40UP037PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-incheck valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-40UP037PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 370W
Current: 2.2 amps
Capacitor: 10 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overloadIngress protection: IP55
Insulation class: F
Power cable length: 1.2 m
Net weight: 7.0 kg
Performance:
Maximum ow: 50 litres per minute (5 taps)
Maximum pressure: 370 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
0.6 1.2 1.8 2.4 3 .0 3.6 4.2 4.8 m3/h
l/min
UP-40UP037
0
10
20
30
40
50
60
8070605040302010
Flow
)m(daeH
7/24/2019 Rainsaver MK5 Data Sheets
7/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-60UP075PC2 - 800403
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-60UP075PC2 Package:
Universal 60UP075PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power andcan be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-60UP075PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-60UP075PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 750W
Current: 4.8 amps
Capacitor: 20 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overload
Ingress protection: IP55Insulation class: F
Power cable length: 1.2 m
Net weight: 11.0 kg
Performance:
Maximum ow: 60 litres per minute (6 taps)
Maximum pressure: 450 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile0.6 1.2 1.8 2.4 3 .0 3.6 4.2 4.8 m3/h
l/min
UP-60U075
0
10
20
30
40
50
60
8070605040302010
Flow
)m(daeH
Performance Curve
7/24/2019 Rainsaver MK5 Data Sheets
8/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALL60UP075PC2 - 800411
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-60UP075PC2 Package:
Universal 60UP075PC2 pressure system pump with auto-restartpump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved exible hoses
x 2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-60UP075PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-incheck valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-60UP075PC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 750W
Current: 4.8 amps
Capacitor: 20 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overload
Ingress protection: IP55
Insulation class: F
Power cable length: 1.2 m
Net weight: 11.0 kg
Performance:
Maximum ow: 60 litres per minute (6 taps)
Maximum pressure: 450 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Stainless steel
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
0.6 1.2 1.8 2.4 3 .0 3.6 4.2 4.8 m3/h
l/min
UP-60U075
0
10
20
30
40
50
60
8070605040302010
Flow
)m(daeH
Performance Curve
7/24/2019 Rainsaver MK5 Data Sheets
9/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-JETCOM82MPC2 - 800404
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is apower failure.
The RS5-JETCOM82MPC2 Package:
DAB JETCOM82MPC2 pressure system pump with auto-restartpump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power andcan be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications
DAB-JETCOM82MPC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
DAB-JETCOM82MPC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 600W
Current: 3.8 amps
Capacitor: 12.5 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overloadIngress protection: IP55
Insulation class: F
Power cable length: 2 m
Net weight: 9.7 kg
Performance:
Maximum ow: 60 litres per minute (6 taps)
Maximum pressure: 460 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Technopolymer
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
Q m3/h0 0,5 1 1,5 2 2,5 3 3,5 40
10
20
30
40
50
0
20
40
60
80
100
120
160
0
0
0
Q l/s
Q l/min
Q IMP gpm
Q US gpm
0
0
0,2 0,4 0,6 0,8 1
10 20 30 40 50 60
Hm H
ft
PkPa
100
200
300
400
2 4 6 8 10 12 14 16
2 4 6 8 10 12 14
JET 82
Hs9
8
54
3 2
7 6
JET 82
JETINOX 82
JETCOM 82
, ,
, , ,
,
, , ,
, , , ,
, , ,
, ,
, , ,
7/24/2019 Rainsaver MK5 Data Sheets
10/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALLJETCOM82MPC2 - 800412
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is apower failure.
The RS5-JETCOM82MPC2 Package:
DAB JETCOM82MPC2 pressure system pump with auto-restartpump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved exible hoses
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself againstvoltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications
DAB-JETCOM82MPC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control tted and wired
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-incheck valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
DAB-JETCOM82MPC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 600W
Current: 3.8 amps
Capacitor : 12.5 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFCMotor protection: In-built thermal overload
Ingress protection: IP55
Insulation class: F
Power cable length: 2 m
Net weight: 9.7 kg
Performance:
Maximum ow: 60 litres per minute (6 taps)
Maximum pressure: 460 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Technopolymer
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
Q m3/h0 0,5 1 1,5 2 2,5 3 3,5 40
10
20
30
40
50
0
20
40
60
80
100
120
160
0
0
0
Q l/s
Q l/min
Q IMP gpm
Q US gpm
0
0
0,2 0,4 0,6 0,8 1
10 20 30 40 50 60
Hm H
ft
PkPa
100
200
300
400
2 4 6 8 10 12 14 16
2 4 6 8 10 12 14
JET 82
Hs9
8
54
3 2
7 6
JET 82
JETINOX 82
JETCOM 82
, ,
, , ,
,
, , ,
, , , ,
, , ,
, ,
, , ,
7/24/2019 Rainsaver MK5 Data Sheets
11/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-JH8003PMPC2 - 800405
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-JH8003PMPC2 Package:
Bianco JH8003PMPC2 submersible pressure system pump with
auto-restart pump controller Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specications BIA-JH8003PMPC2
The pump is a submersible pressure system pump supplied wired
and ready to install. The submersible pump is mounted inside the rain
water tank for silent operation. Used especially for supplying water to
domestic installations.
The pump is characterised by:
Automatic electronic pump control, plug and play
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-JH8003PMPC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 800W
Current: 4.0 amps
Capacitor: 16 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overloadIngress protection: IP68
Insulation class: F
Power cable length: 10 m
Net weight: 5.3 kg
Performance:
Maximum ow: 80 litres per minute (8 taps)
Maximum pressure: 295 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Treated Aluminium
Diffuser and impeller Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile
250 50 75 100
30
0
25
20
15
10
5
Flow (L/m)
Head(m)
BIA-JH8003P
7/24/2019 Rainsaver MK5 Data Sheets
12/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-B42AMPC2 - 800406
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if thereis a power failure.
The RS5-B42AMPC2 Package:
Bianco B42AMPC2 submersible pressure system pump with
auto-restart pump controller Bianco RAINSAVERMK5 automatic Rainwater / Mains Change-
over Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincication
and lead poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against
voltage uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside therain water tank.
Pressure System Pump Specications BIA-B42AMPC2
The pump is a submersible pressure system pump supplied wired
and ready to install. The submersible pump is mounted inside the rain
water tank for silent operation. Used especially for supplying water to
domestic installations.
The pump is characterised by:
Automatic electronic pump control, plug and play
Automatic electronic control provides run dry protection and con-
stant pressure at low ows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.240V single phase TEFC motor with in-built auto reset thermal
overload
83mm elevated suction with algae proof slotted strainer
BIA-B42AMPC2 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 550W
Current: 4.0 amps
Capacitor: 20 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFC
Motor protection: In-built thermal overload
Ingress protection: IP68Insulation class: F
Power cable length: 10 m
Net weight: 12 kg
Performance:
Maximum ow: 105 litres per minute (10 taps)
Maximum pressure: 320 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Technopolymer
Diffuser and impeller Technopolymer
Dual Mechanical seals Carbon/Ceramic/Nitrile on motor side
Silicon Carbide/Ceramic/Nitrile on
pump side (Both in oil bath)
600 80 100 120
35
0
30
20
15
10
5
Flow (L/min)
Head(m)
4020
BIA-B42A
25
7/24/2019 Rainsaver MK5 Data Sheets
13/13
Distributed by White International Pty LtdA.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003
Distributed by White International NZ LtdEastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLANDPh: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344
PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-DIVERTRON1200 - 800407
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is tted with an independent
pressure and ow controller with loss of prime protection and 24
hour auto restart.
No need for oat switch.
RainsaverMK5 General Specications:
Maximum water temperature (mains + pump): 40
0
CMaximum recommended continuous pump ow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an au-
tomatic back up should rain water level be too low, or if there is apower failure.
The RS5-DIVERTRON1200 Package:
DAB DIVERTRON1200 submersible pressure system pump with inter-nal auto-restart pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover
Device
Bianco RAINSAVERMK5 to operate with mains pressure up to 1000
kPa (145 psi)
Suits pump ows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town water
supplies. Safe against waterborne bacteria, dezincication and lead
poisoning
Australian owned and designed
The pump regulates ow and pressure and protects itself against volt-
age uctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and can belocated any distance from the pump, and even inside the rain water
tank.
Pressure System Pump Specications DAB-DIVERTRON1200
The pump is a submersible pressure system pump supplied wired
and ready to install. The submersible pump is mounted inside the rain
water tank for silent operation. Used especially for supplying water to
domestic installations.
The pump is characterised by:
Internal Automatic electronic pump control
Automatic electronic control provides run dry protection and constant
pressure at low ows. Automatic electronic control has built-in check
valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Shaft seal with sand protection boot.
240V single phase TEFC motor with in-built auto reset thermal over-
load
DAB-DIVERTRON1200 Electrical data:
Rated Voltage: 240V
Mains frequency: 50 Hz
Power output: 750W
Current: 4.8 amps
Capacitor: 20 uF
Motor duty: Continuous
Motor type: Asyncronous, TEFCMotor protection: In-built thermal overload
Ingress protection: IP68
Insulation class: F
Power cable length: 15 m
Net weight: 11 kg
Performance:
Maximum ow: 95 litres per minute (9 taps)
Maximum pressure: 470 kPa
General:
Clean water temperature range: 2 350C
Materials:
Pump body Technopolymer
Diffuser and impeller Technopolymer
, .
il i l i , i l .
i i i .
il i l .
.
i li ili .
il l i i ll .
li i .
il l i il i l l i
i i .
1000 1200