Post on 10-Feb-2022
transcript
Research ArticleBackward Surface Wave Propagation and Radiation alonga One-Dimensional Folded Cylindrical Helix Array
Bin Xu and Yang Li
Department of Electrical and Computer Engineering, Baylor University, Waco, TX 76798, USA
Correspondence should be addressed to Bin Xu; bin xu@baylor.edu
Received 28 April 2015; Accepted 30 July 2015
Academic Editor: Diego Masotti
Copyright Β© 2015 B. Xu and Y. Li. This is an open access article distributed under the Creative Commons Attribution License,which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Wave propagation along a closely spaced folded cylindrical helix (FCH) array is investigated for the purpose of designing compactarray for energy transport and antenna radiation. It is found that the height of this surface wave guiding structure can be decreasedfrom 0.24π
0to 0.06π
0by replacing the monopole element with the FCH. Both the propagation constant and the mode distribution
of the dominant wave mechanism are extracted by ESPRIT algorithm, which indicates that a backward propagating surface waveis supported by the array structure. A compact backfire FCH antenna array is designed and measured based on the identifieddominant wave mechanism.
1. Introduction
Wave propagation and radiation along a one-dimensionalmetal wire array has long been of interest since the inven-tion of the Yagi-Uda antenna [1]. With carefully selectedmonopole wire height (0.2 to 0.25π
0, with π
0being the free
space wavelength) and spacing (0.2 to 0.35π0), a surface wave
with an optimum phase velocity can be supported by thestructure and can be radiated in the end-fire direction [2].More recently, there is an emerging interest in minimizingthe size of the array for two important applications: electro-magnetic (EM) energy transport and compact antenna arraydesign. It was found in [3] that the transmission loss of EMenergy along a 1D metal rod array is smaller than 1.5 dB/π
0,
which can be attributed to the strong coupling betweenclosely spaced rods (0.054π
0). For the second application,
a closely spaced, multiple-element parasitic antenna arraywas designed and implemented, with its interelement spacingbeing as small as 0.02π
0[4].
In spite of the above success in reducing the spacingbetween wires, there still remains a challenge to minimizethe height of each array element. It was found that theheight of metal wire should be close to a quarter-wavelengthto ensure the dominant surface wave is strongly excited.One idea to minimize the element size is to substitute themetal wire with electrically small elements such as a folded
spherical helix (FSH) [5] or a folded cylindrical helix (FCH)[6], the size of which can be as small as 0.06π
0. The effects
of mutual coupling between two closely spaced FSHs orFCHs have been studied recently for wireless power transferapplications [7, 8]. However, wave propagation along a 1Dclosely spaced array with electrically small element is not wellunderstood and still needs to be investigated. Previously wehave simulated surface wave propagation along a 1D FCHarray and compared the results with that of a 1D metal cutwire array [9]. In this paper, we extend our study to simulateand measure surface wave propagation and radiation along a1D closely spaced FCH array.
The paper is organized as follows: in Section 2, a 21-element FCH array is first designed and fabricated. Broad-band transmission data and near electric field distributionsare simulated and measured along the array. In Section 3,the dominant propagation mechanism and its associatedpropagation characteristics, such as propagation constant andmode distribution, are extracted using a super resolutionestimation algorithm. A parametric study is performed tofigure out correlation between the propagation constant andarray geometrical parameters. In Section 4, a compact back-fire parasitic antenna array is designed based on the identifieddominant wave mechanism. Both simulation and measure-ment results are presented. Section 5 concludes the paper.
Hindawi Publishing CorporationInternational Journal of Antennas and PropagationVolume 2015, Article ID 210254, 9 pageshttp://dx.doi.org/10.1155/2015/210254
2 International Journal of Antennas and Propagation
y
z2R
H
S Ground planeFeed
Β· Β· Β·
(a) (b)
Figure 1: 1D folded cylindrical helix array setup: (a) simulation and (b) measurement.
300 350 400 450 500β12
β10
β8
β6
β4
β2
0
Frequency (MHz)
Refle
ctio
n co
effici
ent (
dB)
SimulationMeasurement
Figure 2: Simulated and measured reflection coefficients.
2. Wave Propagation along a 1D FCH Array
First, a single 4-arm FCH element centered at 400MHzis designed by using formulas provided in [6]. The helixradius π , height π», and number of turns are 0.0317m,0.047m, and 1, respectively. The height of the folded helixcorresponds to 0.063π
0, which is much shorter than that of
a quarter-wavelength monopole antenna. Next, 21 identicalelements are placed along a straight line in the π¦-axis toform the FCH array. The interelement spacing π is equalto 0.08m, corresponding to 0.11π
0at 400MHz. Figures 1(a)
and 1(b) show the simulation and measurement setup ofthe FCH array. While a finite sized metal ground plane isused in the measurement, an infinitely large perfect electricconductor (PEC) ground is assumed in the simulation tosave computational time. A voltage source is placed at thebottom of the left-most element and a field probe is movedin between parasitic elements to sample the near electricfields at the ground plane level for different frequencies.Numerical software FEKO [10] is used for simulation and
a vector network analyzer (Agilent PNL N5230C) is appliedfor measurement.
Figure 2 compares the simulated andmeasured reflectioncoefficients π
11of the source antenna. They exhibit similar
trend and both are significantly different from the sharpresonance behavior of a single FCH antenna, as presentedin [6]. This is due to the strong coupling between closelyspaced helixes. The resonance band in the measurementshifts downward by approximately 20MHz comparing to thesimulation data, which can be attributed to manufacturingerrors.
Figures 3(a) and 3(b) show the normalized transmissiondata for both simulations and measurements on a dB scale.The antenna mismatches have been removed by normalizing|π21|2 to 1β|π
11|2 and 1β|π
22|2.The horizontal axis represents
the frequency from 300MHz to 500MHz with an intervalof 2.5MHz, and the vertical axis represents the distancebetween transmitting and receiving antennas along theπ¦-axisfrom 0.4m to 1.6m with a spacing of 0.08m. As shown inFigure 3(a), the receiving field strengths are much stronger
International Journal of Antennas and Propagation 3
300 350 400 450 5000.4
0.6
0.8
1
1.2
1.4
1.6D
istan
ce al
ong
Frequency (MHz)
y-a
xis (
m)
(a)
0.4
0.6
0.8
1
1.2
1.4
1.6
Dist
ance
alon
gy-a
xis (
m)
300 350 400 450 500Frequency (MHz)
(b)
Figure 3: Normalized transmission coefficients: (a) simulation and (b) measurement.
0.4 0.6 0.8 1 1.2 1.4 1.60
0.05
0.1
0.15
0.2
β50
β40
β30
β20
β10
0
10
Distance along
Hei
ght i
n
y-axis (m)
z-a
xis (
m)
(a)
0.4 0.6 0.8 1 1.2 1.4 1.60
0.05
0.1
0.15
0.2
β50
β40
β30
β20
β10
0
10
Distance along
Hei
ght i
nz-a
xis (
m)
y-axis (m)
(b)
Figure 4: Simulated near field distribution in the π¦-π§ plane at 390MHz: (a) πΈπ¦and (b) πΈ
π§.
between 355MHz and 415MHz, and within the pass bandwave propagation exhibits negligible decay along the π¦-axis. Outside of this pass band, field strengths are muchweaker and attenuate much faster. The measurement resultsin Figure 3(b) show good agreement with simulation results,except the pass band shifts downward by approximately20MHz, similar to the above observation for Figure 2.
To further reveal the wave propagation along the FCHarray, we simulate the near field distributions in the π¦-π§plane at a sample frequency of 390MHz. Figure 4 plots thenormalized near electric field components πΈ
π¦and πΈ
π§on a dB
scale.The horizontal axis represents the distance along the π¦-axis from 0.4 to 1.6m with a 0.08m interval. The vertical axisrepresents height in the π§ direction from 0 to 0.2m with aninterval of 0.002m. In Figure 4(a), a standing wave pattern
can be clearly observed along the π¦ direction, implying theinterference between +π¦ and βπ¦ traveling waves due to thefinite size of the array. Along the π§ direction, the magnitudeof πΈπ¦peaks at the height of the helix and decays rapidly away
from the interface between the FCH and the air. A similarinterference pattern can be observed in Figure 4(b) for theπΈ
π§
component, except its strength is much weaker than πΈπ¦.
3. Extraction of Dominant WaveMechanism Using ESPRIT
To better understand how wave propagates along the 1DFCH array, we extract the dominant wave mode and itsassociated propagation characteristics from the above trans-mission and near field data. First we model the transmission
4 International Journal of Antennas and Propagation
0.4 0.6 0.8 1 1.2 1.4 1.6β30
β25
β20
β15
β10
β5
0
5
Raw data by simulationFitted curve by ESPRIT
Distance along y-axis (m)
Mag
nitu
de (d
B)
(a)
β5
0
5
10
15
20
0.4 0.6 0.8 1 1.2 1.4 1.6
Raw data by simulationFitted curve by ESPRIT
Distance along y-axis (m)
Unw
rapp
ed p
hase
(rad
)
(b)
Raw data by measurement
0.4 0.6 0.8 1 1.2 1.4 1.6
Fitted curve by ESPRIT
Distance along y-axis (m)
β30
β25
β20
β15
β10
β5
0
5
Mag
nitu
de (d
B)
(c)
Raw data by measurement
0.4 0.6 0.8 1 1.2 1.4 1.6
Fitted curve by ESPRIT
Distance along
β5
0
5
10
15
20U
nwra
pped
pha
se (r
ad)
y-axis (m)
(d)
Figure 5: Comparison between original data with fitted results by ESPRIT: (a) simulated magnitude at 390MHz; (b) simulated unwrappedphase at 390MHz; (c) measured magnitude at 370MHz; (d) measured unwrapped phase at 370MHz.
data as a summation of different wave modes, each with aunique propagation constant π½
π, attenuation constant πΌ
π,
andmagnitude ππ, which can then be extracted using ESPRIT
algorithm. ESPRIT is a super resolution spectrum estimationalgorithm which was originally developed for estimation ofsinusoid signals in noise [11]. More recently, it has beensuccessfully applied to both wave propagation and antennaradiation problems [12]. The extraction process has beenexplained in detail in [4] and will not be repeated here.Consider the following:
π21 β π
β
π=1πππβππ½ππ¦βπΌππ¦. (1)
As an example, Figures 5(a) and 5(b) plot the ESPRITfitted magnitude and phase curves at 390MHz by addingthe first two dominant terms. The results show excellentagreement with the original simulated transmission data,and the propagation constants of the two dominant termsare found to be β2.236π
0and 2.236π
0(π0is the free space
wave number), implying the superposition of incident andreflected components of a single slow wave mode. It is foundthat the dominant mode is a backward traveling surfacewave for the following two reasons: first, the amplitude ofthe mode with a propagation constant π½ = β2.236π
0is
stronger than other modes extracted from the ESPRIT; sec-ond, the unwrapped phase increases as distance π¦ increases,
International Journal of Antennas and Propagation 5
0 0.05 0.1 0.15 0.2β50
β40
β30
β20
β10
0
Nor
mal
ized
Ey
Ey
mag
nitu
deof
dom
inan
t mod
e (dB
)
Height in z-axis (m)
(a)
β30
β20
β10
β15
β25
β35
β5
0
of d
omin
ant m
ode (
dB)
Nor
mal
ized
Ez
Ez
mag
nitu
de
0 0.05 0.1 0.15 0.2Height in z-axis (m)
(b)
Figure 6: Normalized electric field mode distributions at 390MHz: (a) πΈπ¦and (b) πΈ
π§.
340 360 380 400 420β5
β4.5
β4
β3.5
β3
β2.5
β2
β1.5
β1
SimulationMeasurement
Frequency (MHz)
π½/k
0
Figure 7: Extracted phase constants of simulation and measurement against frequency.
as shown in Figure 5(b), implying that the dominant modeis a backward traveling wave. The ESPRIT algorithm is alsoapplied to the measured transmission data at 370MHz andthe comparison between original and fitted data is shown inFigures 5(c) and 5(d). We intentionally shift the frequencydownward by 20MHz to make a fair comparison betweensimulation and measurement, as stated in Section 2. Table 1shows the propagation constants of the dominant backwardsurface wave, and the results are very similar betweensimulation and measurement.
Furthermore, we extract the mode distribution of thedominant surface wave from the simulated near electric fielddata in Figures 6(a) and 6(b). Figures 6(a) and 6(b) plot
Table 1: Propagation parameters of the dominant mode.
Dominant mode π½π/π0
πΌπ/π0
Simulation (390MHz) β2.236 0.0089Measurement (370MHz) β2.4485 0.1584
the extracted πΈπ¦and πΈ
π§mode distributions versus height π§
at 390MHz. It can be seen that the magnitude of πΈπ¦peaks
around the height of the FCH element (0.047m) and decaysexponentially away from the interface, a typical characteristicof surface wave propagation. The πΈ
π§distribution is more
complicated below the interface between the FCH and the air
6 International Journal of Antennas and Propagation
0.029 0.03 0.031 0.032 0.033β4
β3.5
β3
β2.5
β2
β1.5
β1
β0.5
0
Radius (m)
π½/k
0
(a)
0.042 0.044 0.046 0.048 0.05 0.052β3
β2.5
β2
β1.5
β1
Height (m)
π½/k
0
(b)
0.07 0.075 0.08 0.085 0.09 0.095 0.1Spacing (m)
β3
β2.5
β2
β1.5
β1
π½/k
0
(c)
Figure 8: Parametric study on array geometry parameters: (a) radius; (b) height; (c) spacing.
y
z
Ground planeFeed
HHs
0.5π0
Figure 9: 1D compact, closely spaced backfire antenna array.
International Journal of Antennas and Propagation 7
360 380 400 420 440β40
β35
β30
β25
β20
β15
β10
β5
0
SimulationMeasurement
Frequency (MHz)
Refle
ctio
n co
effici
ent (
dB)
Figure 10: Simulated and measured antenna reflection coefficients.
360 380 400 420 440β10
β5
0
5
10
15
SimulationMeasurement
Frequency (MHz)
Gai
n (d
Bi)
Figure 11: Simulated and measured antenna gain.
but is similar to πΈπ¦above the FCH height. We also map out
the frequency dispersion behavior of the backward travelingsurface wave and show the results in Figure 7. It is seen that,except for the 20MHz frequency shift along the horizontalaxis, the values of π½ increase as frequency increases for bothsimulations and measurements.
Finally, a parametric study is conducted to correlatethe propagation constant with array geometrical parameters.The first parameter we examined is the radius π . Boththe height and the spacing between elements are fixed.Figure 8(a) shows that π½ increases as π increases. The secondvarying parameter is the height π» of the helix, as shownin Figure 8(b). The phase constant varies slightly since thetotal length of the helix does not change much. Finally, in
Figure 8(c) we explored the effect of spacing and it wasfound that by increasing the interval of the adjacent elementfrom 0.07m to 0.1m the propagation constant drops fromβ1.83π
0to β2.49π
0due to the variation of coupling between
array elements. It is concluded that by carefully selecting acombination of radius π , height π», and spacing π we canachieve a desired propagation constant π½ for a fixed lengthFCH array. This observation is rather important for thesurface wave antenna design, as will be explained in the nextsection.
4. Backfire Surface Wave Antenna Design
In this section, a compact 1D, closely spaced parasitic antennaarray centered at 400MHz is designed based on the aboveidentified dominant surface wave mechanism. The totallength of the array is assumed to be 0.5π0. Given this fixedarray size, the propagation constant of the surface wave hasto be carefully determined to maximize the directivity of thearray, which is similar to the 1D metal wire antenna arraydesign [4]. The optimum phase constant π½opt for this half-wavelength array is found to be β1.98π
0. Then the radius π ,
heightπ», and spacing π are selected to be 0.03115m, 0.049m,and 0.104m to achieve this π½opt. Other combinations ofarray geometrical parameters can also result in this optimumpropagation constant, as discussed in the previous parametricstudy. Figure 9 plots the final array design setup, whichconsists of four FCH elements. The height of the sourceantenna is tuned to be 0.042m tomatch the input impedanceto 50 ohms at the center frequency.
Figure 10 shows the antenna reflection coefficients versusfrequency. The center resonance frequencies are found tobe 400MHz and 386MHz for simulation and measurement.The β10 dB bandwidthes are both 3MHz. Figure 11 comparesthe simulated and measured gain in the backward end-firedirection (π = 90β, π = 270β). The maximum gain valuesare 10.99 dBi for simulation and 10.33 dBi for measurement.Finally, Figure 12 plots the simulated antenna array radiationpatterns in both the azimuth plane (i.e., π₯π¦ plane) andthe elevation plane (i.e., π¦π§ plane) at the center frequency,which clearly shows the backward radiation pattern. Thesimulated front-to-back ratio is found to be 9.4 dB, while inmeasurement it is 12.8 dB.
To provide more physical insights into our FCH arrayoperation, we compare its interelement phase delay withthe well-known Hansen-Woodyard end-fire array condition[13]. Given the extracted propagation constant (β1.98π
0) and
spacing (0.138π0), the phase delay π
0between adjacent FCH
elements is found to be
π0 = π½optπ = β 1.98π0 Γ 0.138π0 = β 1.72 rad. (2)
According to theHansen-Woodyard end-fire array condition,the theoretical optimum phase delay πHW between adjacentarray elements should be close to
πHW = β(π0π+π
π) = β(
2ππππ+π
π)
= β 1.6525 rad,(3)
8 International Journal of Antennas and Propagation
Table 2: Comparison between our antenna and other small antenna arrays in the literatures.
Reference Number of elements Spacing Height Gain F/B BWOur antenna 4 0.138π
00.06π
010.3 dBi 12.8 dB 0.75%
[14] 3 0.11π0
0.275π0
7.14 dBi 8.6 dB 2.28%[15] 3 0.06π
00.092π
08.5 dBi 7 dB 2.7%
[16] 3 0.09π0
0.1π0
8.43 dBi 6.63 dB 1.2%[17] 3 0.053π
00.21π0
9.9 dBi n/a 12.44%
30
210
60
240
90270
120
300
150
330
180
0
10dBi
5dBi
0dBi
(a)
30
β150
60
β120
90β90
120
β60
150
β30
180
0
10dBi
5dBi
0dBi
(b)
Figure 12: Simulated radiation patterns at 400MHz: (a) azimuth plane and (b) elevation plane.
where π is speed of light andπ is number of elements. It canbe seen thatthe phase delay of our FCH array π
0is close to
that of Hansen-Woodyard end-fire condition πHW, resultingin its maximum radiation in the βπ¦ direction.
Finally, we compare our FCH antenna array performancewith other small antenna arrays in the literatures [14β17].The comparison is shown in Table 2. It can be clearly seenthat our FCH array exhibits the lowest height, highest gain,and best front-to-back (F/B) ratio among all antennas. Thetradeoffs we made include one more element and slightlylarger spacing. The β10 dB input bandwidth of our antennais the smallest, which can be attributed to the lowest height ofthe FCH element.
5. Conclusion
In this paper, surface wave propagation and radiation alonga 1D FCH array is investigated from both simulation andmeasurement perspectives. It is found that a backward trav-eling surface wave can be supported by this structure. Thepropagation characteristics of this dominant wave mecha-nism are extracted and discussed. Furthermore, a backfiresurface wave antenna is designed and implemented basedon the identified wave mechanism. The study presented inthis paper opens a new door for low-profile parasitic surfacewave antenna array design. For future work, we will expandthe study to array structures with other electrically smallelements such as the folded spherical helix or the meanderline.Wewill also look into the possibility of applying the FCHantenna array for wireless power transfer.
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
References
[1] G. Thiele, βAnalysis of yagi-uda-type antennas,β IEEE Transac-tions on Antennas and Propagation, vol. 17, no. 1, pp. 24β31, 1969.
[2] H.W. Ehrenspeck andH. Poehler, βA newmethod for obtainingmaximum gain from yagi antennas,β IRE Transactions onAntennas and Propagation, vol. 7, no. 4, pp. 379β386, 1959.
[3] S. A.Maier, M. L. Brongersma, andH. A. Atwater, βElectromag-netic energy transport along arrays of closely spaced metal rodsas an analogue to plasmonic devices,β Applied Physics Letters,vol. 78, no. 1, pp. 16β18, 2001.
[4] D. Xue and Y. Li, βDesign of a closely-spaced, multiple-elementparasitic antenna array,β Microwave and Optical TechnologyLetters, vol. 56, no. 10, pp. 2374β2377, 2014.
[5] S. R. Best, βThe radiation properties of electrically small foldedspherical helix antennas,β IEEE Transactions on Antennas andPropagation, vol. 52, no. 4, pp. 953β960, 2004.
[6] S. R. Best, βA comparison of the cylindrical folded helix Q to theGustafsson limit,β in Proceedings of the 3rd European Conferenceon Antennas and Propagation (EuCAP β09), pp. 2554β2557,Berlin, Germany, March 2009.
[7] M. Skiljo and Z. Blazevic, βSpherical helices for resonantwireless power transfer,β International Journal of Antennas andPropagation, vol. 2013, Article ID 426574, 12 pages, 2013.
[8] J. Lee and S. Nam, βFundamental aspects of near-field couplingsmall antennas for wireless power transfer,β IEEE Transactions
International Journal of Antennas and Propagation 9
on Antennas and Propagation, vol. 58, no. 11, pp. 3442β3449,2010.
[9] B. Xu, R. Jean, and Y. Li, βInvestigation of surface wave propa-gation along a folded cylindrical helix array,β in Proceedings ofthe IEEE Texas Symposium on Wireless and Microwave Circuitsand Systems (WMCS β15), Waco, Tex, USA, April 2015.
[10] https://www.feko.info/.[11] A. Paulraj, R. Roy, and T. Kailath, βEstimation of signal
parameters via rotational invariance techniquesβESPRIT,β inProceedings of the 19th Asilomar Conference on Circuits, Systemsand Computers, pp. 83β89, November 1985.
[12] Y. Li andH. Ling, βExtraction of wave propagationmechanismsin a cut-wire array using the ESPRIT algorithm,β IEEEAntennasand Wireless Propagation Letters, vol. 8, pp. 744β747, 2009.
[13] W. L. Stutzman and G. A. Thiele, Antenna Theory and Design,John Wiley & Sons, 2012.
[14] Z. Bayraktar, P. L. Werner, and D. H. Werner, βThe designof miniature three-element stochastic Yagi-Uda arrays usingparticle swarm optimization,β IEEE Antennas and WirelessPropagation Letters, vol. 5, no. 1, pp. 22β26, 2006.
[15] S. Lim and H. Ling, βDesign of electrically small, patternreconfigurable Yagi antenna,β Electronics Letters, vol. 43, no. 24,pp. 1326β1327, 2007.
[16] J. Yu, Y. Le, and S. Lim, βDesign of a dual-band, electricallysmall, parasitic array antenna,β IEEE Antennas and WirelessPropagation Letters, vol. 13, pp. 1453β1456, 2014.
[17] D. Arceo and C. A. Balanis, βA compact Yagi-Uda antenna withenhanced bandwidth,β IEEE Antennas andWireless PropagationLetters, vol. 10, pp. 442β445, 2011.
International Journal of
AerospaceEngineeringHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
RoboticsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Active and Passive Electronic Components
Control Scienceand Engineering
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
RotatingMachinery
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporation http://www.hindawi.com
Journal ofEngineeringVolume 2014
Submit your manuscripts athttp://www.hindawi.com
VLSI Design
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Shock and Vibration
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Civil EngineeringAdvances in
Acoustics and VibrationAdvances in
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Electrical and Computer Engineering
Journal of
Advances inOptoElectronics
Hindawi Publishing Corporation http://www.hindawi.com
Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
SensorsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Modelling & Simulation in EngineeringHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Chemical EngineeringInternational Journal of Antennas and
Propagation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Navigation and Observation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
DistributedSensor Networks
International Journal of