Post on 11-Nov-2015
description
transcript
INSTALLATION INSTRUCTIONS
801 Avenida Acaso, Camarillo, Ca. 93012
(805) 494-0622 www.sdcsecurity.com
E-mail: service@sdcsecurity.com
S6100 SERIES
REVERSIBLE PANIC/FIRE EXIT
RIM DEVICES
These instructions are presented a in step by step sequence.
Please read it through before installation.
Note: The dimensions of the Template are shown in inches. See
attached page for the Metric Conversion Table for millimeters.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd Rev - 12/10 Page 1
P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd Rev - 12/10 Page 2
A. DESIGNATION OF PARTS
B. TYPE OF INSTALLATION
A. Single Door B. Double Door with Mullion C. Double Door without Mullion
2-7/16CL
TRIM TRIM
DOOR DOOR
MULLION2-7/16
CL
TRIM
DOOR
C. MARK POSITION FOR INSTALLING 1. Mark the center line of device by drawing a line
across the door and stop 40" above the finished floor
as shown at right.
2. Prepare door for you specific device per supplied template.
3. Drill holes as marked on door and jamb or mullion.
INSIDE
FACE
OF DOOR
JAMB
CL OF STRIKE
40" to
Finished
Floor
CL OFDEVICE
2-7/16CL
TRIM TRIM
DOOR DOOR
DOUBLE DOOR
STRIKE
Strike
Chassis Cover
Chassis
Chassis
Latch Assembly
Push Bar
End Cap
End Cap Bracket
Dogging Device
(Fire Exit Hardware is not
Equipped with this device)
P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd Rev - 12/10 Page 3
STOP LINE
Jamb
of Device
Strike
LC
Strike
Site
Door
D. INSTALL STRIKE TO FRAME 1. Place strike over the drilled holes, and attach it to
the jamb or mullion with the supplied screws.
2. If installing with a vertical rod device for double
doors, and additional Double Door Strike must be
used in place of the regular strike provided.
E. IF CYLINDER IS INCLUDED WITH THE DEVICE 1. Drill one 1-3/16" diameter thru hole for the cylinder/bracket plate.
2. Insert cylinder and cylinder collar from outside of door.
3. Place bracket plate on inside of face of the door.
4. Put two cylinder mounting screws through the bracket plate and
into the cylinder.
5. Cut the cylinder mounting screws and tailpiece to the required door
thickness at break-off points, then fasten screws.
F. INSTALL OUTSIDE TRIM Mark and drill holes for the outside trim (see trim instructions).
E. INSTALL DEVICE BODY 1. Remove chassis cover from latch assembly
and end cap from end cap bracket.
2. Place the device horizontally over the drilled holes and
attach with the supplied mounting screws. Bolt
device chassis to trim with sexbolts (if required).
3. Make sure cylinder or trim actuator shaft (tailpiece) can
insert into device cam concentrically (see device cam
at right).
4. Install end cap bracket on device, then screw to door.
5. Tighten all screws or bolts.
Device Cam
Insert Trim Actuator Shaft
Into device cam +.
Latch
Assembly
Outside face of door
Cylinder Collar
Rim Cylinder
Cylinder
Actuator shaft
(Tailpiece)
Inside face of door
Cylinder
bracket plate
Cylinder mounting
screws
Tailpiece projection
1/4
P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd Rev - 12/10 Page 4
H. INSTALL COVERS
NOTE: The Device bar has 3 different lengths;
Standard 3' Door Device = Approx 33"
Standard 3.5' Door Device = Approx 40"
Standard 4' Door Device = Approx 44"
The bar lengths of devices are pre-cut for 36", 42" and
48" wide door, no additional cutting is necessary.
If narrower door installation is needed, cut device at the
A location, to door width minus 4" to fit properly.
1. Test push bar operation before installing covers:
a. No Trim: Latch bolt is retracted by push bar
inside.
b. With Trim: Latch bolt is retracted by push bar
inside, key or lever/knob outside.
c. Dogging: See dogging description and chart
below.
2. Make sure and secure latch bolt engagement. Adjust
strike if required.
3. Install chassis cover on chassis.
4. Install end cap.
Note: For increasing the life of this device,
dogging device during high traffic
period of the day (Panic device only).
Dogging Wrench
(Allen Key) Dogging:
Depress push bar,
Insert dogging wrench
and turn clockwise 35 degrees.
Depress
push bar
The push bar will remain
depressed and the latch will
remain retracted
Release Dogging:
Depress push bar,
Insert dogging wrench and
turn counter-clockwise 35 degrees.
Depress
push bar
The push bar will return to up
position and the latch will project
to lock the door.
Latch
Assembly
Mark mounting holes
through End Cap
Bracket
after device is level
A
INSTALLATION INSTRUCTIONS
801 Avenida Acaso, Camarillo, Ca. 93012
(805) 494-0622 www.sdcsecurity.com
E-mail: service@sdcsecurity.com
S6200 SERIES
PANIC/FIRE EXIT
SURFACE MOUNTED
VERTICAL ROD DEVICES
These instructions are presented
in a step by step sequence.
Please read it through before
installation.
Note: The dimensions are shown
in inches. See attached page for
the Metric Conversion Table for
millimeters.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01/11 Page 1
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01/11 Page 2
DESIGNATION OF PARTS
Top Strike Fixing Plate
Top Strike
(Back View)
Top Latch
Assembly
Top Rod
Shaft Connector
Bottom Strike
Base
Bottom Strike
(Fire Label)
End Cap
End Cap Bracket
Mechanism
Housing
Dogging Device Fire Exit
Hardware is not equipped
with this device
Push Bar
Bottom Strike
(Panic Label)
Chassis
Cover
CAUTION:
Before installing
this device, check
contents of box
for size of device,
function, finish
color and outside
trim to be used.
Top Strike
(Panic Label)Top Strike
(Fire Label)
Bottom Latch
Assembly Cover
Top Latch
Assembly Cover
Mounting
Bracket
Chassis
Assy.
Rod Guide
Mounting
Bracket
Bottom Latch
Assembly
Bottom Rod
Rod Guide
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 3
STEP 1: PREPARE DOOR
1. Mark position of holes on the door per template (see figure 1).
2. Drill all holes marked on the door for the device chassis and top and bottom latch mounting
brackets.
3. Mortise hole for outside trim is required.
NOTE; Any hole drilled from the outside, first needs a pilot hole drilled from the inside
to ensure good alignment.
Figure 1
2-7/16Mark BacksetJAMB
2-5/16"3-7/32"
INSIDE FACE OF DOOR
1016mm
(40")
Mark of deviceCL
3-7/32"
1-15/32"
1/4
of top and bottom latchesCL
Surface of the door must be
flush. Clear away any raised
jutting to allow the exit device to
rest on flat surface of the door.
40" to finished floor
Standard centerline height of device is 40" above the finished floor.
Prepare door for your specific
device per supplied template.
STEP 2: INSTALL BRACKETS, DEVICE & TRIM1. Remove chassis cover from chassis assembly and end cap from end cap bracket.
2. Cut the length if required.
For user information; This model device has three different lengths:
For use on 3' wide door, device = 33"
For use on 3.5' wide door, device = 40"
For use on 4' wide door, device = 44"
a. The device length is pre-cut for use on 36", 42" or 48" wide doors, no additional
cutting is necessary. If narrow door installation is required, cut device at section A
to door width minus 2" for proper fit.
b. Remove device from door, remove end cap and end cap bracket and cut where required.
NOTE: Device must be cut flat with all burrs removed for end cap to fit properly.
3. Mount device horizontally via the drilled holes and secure with supplied
mounting hardware. Attach device to trim or sexbolt.
4. Check that the trim actuator shaft fully inserts into the
device cam (refer to view B).
5. Install end cap bracket to device, level device
and mark then drill the mounting
holes. Attach to door with hardware
supplied. Attach end cap.
6. Install mounting brackets to top
and bottom of door.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 4
A
Hinge Stile edge of door
Mark mounting
holes thru end
cap bracket after
device is leveled.
Mounting
Bracket
Chassis
End cap
bracket
Figure 2
VIEW B
Insert Trim Actuator Shaft
Into Device Cam
*
*
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 5
STEP 3: INSTALL BOTTOM ROD AND BOTTOM STRIKE1. Mount the bottom latch assembly into the mounting bracket (see figure 3).
2. Screw the threaded end of the bottom rod onto the bottom latch assembly (see figure 4).
3. Using screw supplied, attach and tighten the bottom rod to the chassis at the location
indicated by the arrow in figure 5.
NOTE: If the hole on the bottom shaft connector does not align with the mounting hole in
the chassis, adjust the length by turning the rod in or out of the latch assembly.
4. Install bottom strike into finished floor or threshold, and be sure to align center line of bottom
latch with the centerline of the bottom strike (see figure 6)
5. Depress and release push bar to confirm proper installation.
5-1 Make sure bottom latch can be retracted and flush with
the edge of the door when push bar is depressed.
5-2 Check bottom latch bolt has 19/32" (15mm) throw min.
when push bar is released.
Figure 3 Figure 4
Threaded end of
Bottom rod
Figure 6
1/4
2-1/4
7/82-3/32
LC
Figure 5
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 6
STEP 4: INSTALL TOP ROD AND TOP STRIKE1. Mount the top latch assembly into the mounting bracket (see figure 7).
2. Screw the threaded end of the top rod onto the top latch assembly completely (see figure 8).
Threaded end
of top rodFigure 7
Figure 8
3. Measure and cut the length of the top rod. The length of the top rod is measured to the edge of
the rod connector (see figure 9) which will be attached to the chassis.
4. Insert the rod connector into the non-threaded end of the top rod and secure in place by
tightening the locking screw (see figure 10).
5. With the top rod connector installed, attach the top rod to the chassis at the location indicated
by the arrow (see figure 11).
Edge of rod
connector
Mark cutting line
and cut top rod
Figure 9
Non-threaded
end of top rod
Locking
screw Figure 10 Figure 11
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 7
6. Mark and drill mounting holes on the jamb for the top strike per the strike template (see figure 12).
Fasten the top strike to the jamb with the screws supplied (see figure 13).
STEP 5: TEST OPERATION1. Depress the push bar. The top and bottom latches should be held retracted. The bottom latch
should also clear the floor and the bottom strike. Door can now be opened.
2. Release push bar, both the top latch bolt and the bottom latch bolt should be fully extended.
3. Check device operation by depressing and releasing push bar several times to assure final
installation is correct.
4. Repeat device operation by opening and closing door several times using the
outside trim to make sure all installations have no problems.
5. Repeat adjustment procedure if either the top latch bolt is not held
retracted, or bottom latch bolt does not clear floor and bottom strike.
STEP 6: INSTALL COVERS1. Before installing covers, check and secure top and bottom latch
bolts engagement. Adjust strikes if necessary.
2. Install the chassis and top & bottom assembly covers and the
two rod guides (see figure 14).
Figure 13
Figure 14
Figure 12
NOTE:
Attach third screw last after strike
has been properly aligned,
Door HandingUse this diagram to determine the hand of door.
NOTE:
To extend the life of this device,
it is recommended to activate
the dogging feature during high
traffic periods of the day.
Depress
Push Bar
Depress
Push Bar
Dogging:Insert dogging wrench and
turn clockwise 15 degrees.
The push bar will remain
pressed and the latches
will remain retracted.
Release Dogging:Insert dogging wrench and
turn counter-clockwise 15 degrees.
The push bar will return to the
up position and the latches will
extend to lock the door.
Dogging Wrench
Outside of Door
Inside of Door
RHR LHR
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 8
INSTALLATION INSTRUCTIONS
801 Avenida Acaso, Camarillo, Ca. 93012
(805) 494-0622 www.sdcsecurity.com
E-mail: service@sdcsecurity.com
S6800 SERIES
PANIC/FIRE EXIT
CONCEALED VERTICAL ROD DEVICES
These instructions are presented in a step by step sequence.
Please read it through before installation.
Note: The dimensions of the Template are shown in inches. See
attached page for the Metric Conversion Table for millimeters.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 1
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 2
DESIGNATION OF PARTS
Top Strike Fixing Plate
Top Strike
(Back View)
Latch Mounting
Plate
Top Latch
Assembly
Top Rod
Shaft Connector
Latch Actuated
Shaft
Bottom Latch
Assembly
Bottom Rod
Bottom Strike
Base
Bottom Strike
(Fire Label)
End Cap
End Cap Bracket
Mechanism
Housing
Dogging Device Fire Exit
Hardware is not equipped
with this device
Push Bar
Bottom Strike
(Panic Label)
Chassis
Cover
CAUTION:
Before installing
this device, check
contents of box
for size of device,
function, finish
color and outside
trim to be used.
Top Strike
(Panic Label)Top Strike
(Fire Label)
Rod Length
Locator
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 3
A. PREPARE DOOR 1. Mark centerline of device by
drawing a line across the door.
2. Mark a backset line and 4 thru
holes for device chassis shown
on the template provided.
3. Prepare the door cut-outs by
using the template provided.
Figure 1-2
4. Cut out the top edge and bottom edge of the door, then weld two 5mm thick mounting plates
on both edges for Top and Bottom Latch Assemblies (figure 1-2).
5. Drill holes and use a #10-24 tap on the mounting plates on the top and bottom of door.
The centerline of the
device must be 40"
above the finished
floor. Bottom Door
gap MUST be 1/4.
2-7/16"
of DeviceLC
Mark backset from edge of door
INSIDE FACE OF DOOR
Drill holes and
cut-outs on the
Device side ONLY
of DeviceLC
39-3/
4
See Trim Installation
Instructions for outside
face of door preparation.
Figure 1-1
1-3/4
2-1/4
7/8"
2-7/16
1-19/32"
1-9/32"
1-5/32"
23/32"
1-11/16"
7/16"
7/8"
7/8"
Inside Face
of Door
1-17/32"
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 4
B. ASSEMBLE RODS AND LATCHES1. Screw bottom rod into bottom latch assembly (figure 2-1).
2. Assemble top rod:
2-1 Connect short top rod to long top rod using rod connector (figure 2-1).
2-2 Measure and cut the length of the top rod if it is too long.
2-3 Insert shaft connector into the non-threaded end of the top rod and tighten screw
to fix in place (figure 2-3).
3. Screw top rod assembly into top latch assembly (figure 2-4).
Shaft connector
Non-threaded
End of top rod
Non-threaded
End of top rod
Top latch
assembly
Top rod
assembly
Figure 2-4Figure 2-3
Figure 2-2Figure 2-1
Bottom latch
assembly
Bottom rod
C. MOUNT LATCH ASSEMBLIES1. Attach latch mounting brackets to top and bottom latch assemblies
2. Insert top latch assembly into top of the door and fasten to the mounting plates
with the screws provided (figure 3-1).
3. Insert bottom latch assembly into bottom of the door and fasten to the mounting plates
with the screws provided (figure 3-2).
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 5
Latch mounting bracket
Top latch assembly
Mounting
plate
Figure 3-1
Top o
f doo
r
Mounting
plate
Bottom latch
assembly
Latch mounting
bracket
Figure 3-2
Botto
m of
door
D. ADJUST VERTICAL RODS1. Place the rod length locator through the cut-outs on the inside face of the door. Hook a shaft
connector with the small stud on the locator. When the shaft connector is raised to as level as
possible, the holes C or D in the locator should align with the cut-outs A or B (figure 4-1).
2. If the C or D holes in the locator do not align with their respective cut-out, then the vertical rod
length is incorrect and must be adjusted.
Top latch
assembly
Bottom latch
assemblyRod Length
LocatorStud for
hooking
Cut-Out A
Cut-Out B
Hole C
Hole D
Figure 4-1
Top shaft
of DeviceLC
Bottom shaft
of DeviceLC
3. Adjustment procedure:
Adjust the length of the two vertical rods by hand through the cut-outs (figure 4-2).
Shorten or lengthen the rods by turning into or out of the latch assemblies (figure 4-3)
until the holes of the shaft connectors are in the proper position as determined by the
latch length locator (pg. 5, figure 4-1).
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 6
E. INSTALL LATCH ACTUATOR SHAFTS1. Attach one Latch Actuated Shaft to the top and bottom shaft
connectors (figure 5) with screws supplied.
2. Make sure both top and bottom latch actuated shafts are parallel.
F. INSTALL DEVICE AND TRIM (if applicable)1. Remove device chassis cover from the chassis assembly and the
end cap from the end cap bracket.
2. Position the device on the door and insert latch actuated shafts into
the slots marked X and Y (figure 6-1). Fasten in place with
screws supplied.
Figure 4-2Figure 4-3
Figure 5
Latch Actuated
Shaft
Figure 6-1
X
Y
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 7
3. Cut the length if required:
a. The device length is pre-cut for use on 36", 42" or 48" wide doors, no additional cutting is
necessary. If narrow door installation is required, cut device at section A to door width
minus 2" for proper fit.
b. Remove device from door, remove end cap and end cap bracket and cut where required.
NOTE: Device must be cut flat with all burrs removed for end cap to fit properly.
4. Mount device horizontally via the drilled holes and secure with supplied mounting hardware.
Attach device to trim or sexbolt (if applicable).
5. Install end cap bracket to device and attach to door with hardware supplied. Attach end cap.
Figure 6-2
G. TEST OPERATION AND HANG DOOR.1. Depress push bar. Top latch bolt should be retracted as shown (figure 7-1) and
bottom latch clears floor and bottom strike (figure 7-2).
Figure 7-1
BOTTOM
LATCH BOLT
(Clears floor
and strike).
Figure 7-2
A
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 8
2. Release push bar, Make sure both top and bottom latch bolts are FULLY extended
3. Check top latch bolt for deadlocking function.
Depress the deadlock plate by hand.
When the deadlock plate is depressed,
the latch bolts should be locked in the
extended position and unable to be pressed
down (figure 7-3).
4. Check device operation by depressing and releasing push bar several times to assure
correct final installation.
5. Hang door (with device installed) and repeat operation check with outside lever.
6. redo rod length adjustment if either top latch bolt is not held retracted or if the bottom
latch bolt does not clear the floor and bottom strike.
Figure 7-3
Top Latch
Bolt
Deadlock
Plate
.079"
.985"1.831"
1.496"
2.441"1.339"
1.417"
1.969"
2.598"
.472"
1.339"
.748"1.732"3.150"4.134"
.236"
Figure 8-1
Figure 8-2
H. INSTALL TOP STRIKE1. Prepare frame:
a. Cut out a square on the frame
for the top strike (figure 8-1).
b. Weld two 3mm thick mounting
plates on the frame (figure 8-2).
c. Drill holes and tap #10-24 threads
on the mounting plates.
2. Install the top strike on the mounting plates (figure 8-3) and secure with supplied screws (figure 8-4).
Figure 8-3 Figure 8-4
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 9
I. INSTALL BOTTOM STRIKE1. Bore the hole into the finished floor or threshold (figure 9-1).
2. Install bottom strike into the hole (figure 9-2).
NOTE:For flat thresholds the
clearance must be provided
in sill to accommodate full
9/16" (15mm) throw of latch
bolt.
1/4 1/4
Flat threshold application
(Panic device ONLY)Strike application
J. INSTALL COVERS
1. Test push bar operation before installing covers;
a. No Trim: Latch bolts are retracted by the push
bar inside.
b. With Trim: Latch bolts are retracted by the push
bar inside, key or lever/knob outside.
c. Dogging: See dogging description and chart
page 10.
2. Check latch bolt engagement, adjust strikes
if required.
3. Install chassis cover over chassis assembly.
4. Install end cap.
2.441"
1.126"
1.850"
DOOR
(Top View)
CLof Bottom Latch
CLof Bottom Latch.748"
DIAMETER
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd Rev - 12/10 Page 10
Door HandingUse this diagram to determine the hand of door.
NOTE:
To extend the life of this device,
it is recommended to activate
the dogging feature during high
traffic periods of the day.
Depress
Push Bar
Depress
Push Bar
Dogging:Insert dogging wrench and
turn clockwise 15 degrees.
The push bar will remain
pressed and the latches
will remain retracted.
Release Dogging:Insert dogging wrench and
turn counter-clockwise 15 degrees.
The push bar will return to the
up position and the latches will
extend to lock the door.
Dogging Wrench
Outside of Door
Inside of Door
RHR LHR
P:\INSTALLATION INST\SWITCH KITS\INST-S6000-ATS.vsd REV - 04-12 Page 1
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
INSTALLATION INSTRUCTIONS
S6000-ATS ANTI-TAMPER SWITCH KIT
Electrical Specifications:WHT = COM
YEL = N/O
ORG = N/C
5AMPS @ 250V
Resistive
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622
www.sdcsecurity.com E-mail: service@sdcsecurity.com
Insert Anti-Tamper Switch
where shown.
Insert the S6000-ATS Assy. into the device. Slide the End Cap over the
End Cap Bracket. Position the S6000-ATS Assy so the switch arm
makes contact and is activated by the inside surface of the End Cap.
Hold the S6000-ATS Assy. in place as you slide out the End Cap.
Tighten the set screws on the S6000-ATS to lock it in place.
Once S6000-ATS Switch Assembly is properly located, wire
the switch and re-install the Device Cover and End Cap.END CAP
Switch Arm
Remove
Device Cover
and End Cap.
DEVICE
COVER
END CAP
END CAP
BRACKET