Post on 11-Jan-2016
transcript
SURFACE ELECTRIC WATER PUMPSFOR DOMESTIC AND INDUSTRIAL USE
City Pumps s.r.l.
Via Enrico Fermi, 27 - P.O. BOX 8437047 San Bonifacio (Verona) Italy
Tel. (+39) 045 6102379Fax (+39) 045 7614264
e-mail: sales@citypumps.comwww.citypumps.com
�
Introduction
C o m p a n y p r o f i l e
CITY PUMPS is the latest breakthrough from INOX POMPE. The company has undergone a restyling with a European brand image and an international repute in the manufacture of electric water pumps for civilian, agricultural and industrial applications.
The productive standards implement all the electric and hydraulic inspections prescribed by the EU safety regulations and use productive plants that are among the technologically most advanced in the electro tech-nical and mechanical industry.
We export to over 50 countries.
CITY PUMPS works in conjunction with leading interna-tional groups in the research and production of civilian and industrial electric water pumps.
5
a wide range of...
100 100 1000 10000Q (l/min)
0
20
40
60
80
100
120
H (m)
CIVILIAN / DOMESTIC
INDUSTRIAL
Introduction
Performances of City Pumps’ surface range of water pumps.
City Pumps offers a wide range of electric water pumps for domestic, civilian and industrial applications.
Its range of products meets the requirements of an effi-cient product, simple to use, flexible and with low power consumption.
�
...electric water pumps...
Products Range of performance Applications Page
IP
Flow rate up to 50 l/min (3.0 m3/h)Head up to 90 m
They are recommended for pumping clean water without abrasive particles and liquids that are chemically non aggressive to the materials from which the pump is made. For their reliability, simplicity of use and economy they are suitable for domestic use and in particular for distributing water in combination with small pressure sets, for irrigating gardens. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 10
IQ
Flow rate up to 50 l/min (3.0 m3/h)Head up to 90 m
They are recommended for pumping clean water without abrasive particles and liquids that are chemically non aggressive to the materials from which the pump is made.The hydraulic characteristics of these pumps, together with their compactness, make them suitable for use in the industrial sector. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 12
IC
Flow rate up to 1�0 l/min (9.� m3/h)Head up to 58 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. Reliable and maintenance free they are widely used in the domestic and civil sector, in particular for water distribution in combination with small or medium pressure sets, for transfer in general, for irrigating gardens. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 14
IC-SS Maximum flow rate 1�0 l/min
(9.� m3/h)Maximum head 23 m
It is recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. The construc-tion of these centrifugal pumps makes them suitable for use in the domestic, agricultural and industrial sector. All the wetted parts are in stainless steel AISI 304 to guarantee total hygiene and maximum resistance to corrosion. The pump must be installed in enclosed places, or at least protected against inclement weather.
Page 16
ICn Flow rate up to 250 l/min
(15 m3/h)Head up to 57 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. The pumps in this series are made to standards EN 733 - DIN 24255 and are specifically used in the civil, industrial or agricultural sectors where their characteristics of sturdiness and reliability can be best appreciated. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 18
ICH
(med
ium
flow
rate
s)
Flow rate up to �00 l/min (3� m3/h)Head up to 39 m
The ICH series is recommended for civil, agricultural and industrial applica-tions. The high flow rates and continuous rating make it ideal for irrigation with flowing and sprinkling water, for drawing water from lakes, rivers, wells, or for industrial applications that need to achieve large flow rates at medium-low heads. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 20
7
...for any requirement...electric water pumps...
Products Range of performance Applications Page
ICH
(hig
h flo
w ra
tes)
Flow rate up to 1800 l/min (108 m3/h)Head up to 2�.5 m
The ICH series is recommended for use in the civil, agricultural and industrial field. The high flow rates and continuous rating make it ideal for irrigation with flowing and sprinkling water, for drawing water from lakes, rivers, wells, or for industrial applications that need to achieve large flow rates at medium-low heads. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 22
NCO Flow rate up to 350 l/min
(21 m3/h)Head up to 20 m
They are recommended for pumping water and liquids that are chemically non aggressive to the materials from which the pump is made. The open impeller design allows the pumping of liquids with relatively high levels of impurities without risk of clogging the impeller. For this reason the NCO se-ries are suitable for use in industry, for the transfer of water from canals, riv-ers, reservoirs, tanks, etc. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 24
PRO-
NCO Flow rate up to 350 l/min
(21 m3/h)Head up to 20 m
They are recommended for pumping water and liquids that are chemically non aggressive to the materials from which the pump is made. The open impeller design allows the pumping of liquids with relatively high levels of impurities without risk of clogging the impeller. For this reason the PRO-NCO series are suitable for use in systems for washing fruit, vegetables, fish, shellfish, meat, in industrial systems for washing metal parts, glass containers, and for the circulation of cooling liquids.The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 26
ICB Flow rate up to �00 l/min
(2� m3/h)Head up to 112 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. Their high efficiency and adaptability to the most varied, even unusual ap-plications, make them the ideal choice in the domestic, civil and industrial field; in particular for distributing water in combination with pressure sets, for increasing pressure in the mains, for fire-fighting sets. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 28
MSG
Flow rate up to 130 l/min (7.8 m3/h)Head up to �7 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. Due to their reliability, quiet running and low maintenance, they are suitable for domestic applications including water supplies (as a pressure set), garden irrigation, etc. The pumps must be installed in enclosed places, or at least protected against inclement weather
Page 36
MS 0
7-08 Flow rate up to 120 l/min
(7.2 m3/h)Head up to 50 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made.Due to their reliability and quiet running, they are suitable for domestic applica-tions including water supplies (as a pressure set), garden irrigation, etc. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 38
8
Products Range of performance Applications Page
VMS A Flow rate up to 80 l/min
(�.8 m3/h)Head up to 105 m
They are recommended for pumping clean water and liquids that are che-mically non aggressive to to the materials from which the pump is made. Their reliability and quiet running make them suitable for domestic and civil applications, because the pump is fully submersible with the motor cooled by the pumped liquid, it can be used safely in wet environments and in spaces with insufficient ventilation.
Page 40
VMS B
Flow rate up to 120 l/min (7.2 m3/h)Head up to 105 m
They are recommended for pumping clean water and liquids that are chemi-cally non aggressive to the materials from which the pump is made.Their reliability and quiet running make them suitable for domestic and civil applications, because the pump is fully submersible with the motor cooled by the pumped liquid, it can be used safely in wet environments and in spaces with insufficient ventilation.
Page 42
VMSE
A Maximum flow rate 80 l/min (�.8 m3/h)Head up to 105 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. Their reliability and quiet running make them suitable for domestic and civil applications and, because the pump is fully submersible with the motor cooled by the pumped liquid, it can be used safely in wet areas and in spaces with insufficient ventilation. The enclosed design also eliminates the possibility of water escaping as a result of seal failure, making it suitable for use in carpeted or other delicate environments
Page 44
VMSE
B Maximum flow rate 120 l/min (7.2 m3/h)Head up to 105 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. Their reliability and quiet running make them suitable for domestic and civil applications and, because the pump is fully submersible with the motor cooled by the pumped liquid, it can be used safely in wet areas and in spaces with insufficient ventilation. The enclosed design also eliminates the possibility of water escaping as a result of seal failure, making it suitable for use in carpeted or other delicate environments.
Page 46
JS
(up
to 0.
85 H
P)
Flow rate up to 50 l/min (3 m3/h)Head up to �7 m
They are recommended for pumping clean water and liquids that are chemi-cally non aggressive to the materials from which the pump is made. JS self-priming pumps are designed for suction lifts and can be positioned above the water source, including applications with air entrained in the water. Due to their reliability and low maintenance, they are recommended for domestic use, including water distribution (as part of a pressure set), garden irrigation, etc.The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 48
a complete line of electric water pumps...
9
Products Range of performance Applications Page
JS
(from
1 to
1.5 H
P)
Flow rate up to 80 l/min (�.8 m3/h)Head up to 70 m
They are recommended for pumping clean water and liquids that are chemi-cally non aggressive to the materials from which the pump is made. JS self-priming pumps are designed for suction lifts and can be positioned above the water source, including applications with air entrained in the water. Due to their reliability and low maintenance, they are recommended for domestic use, including water distribution (as part of a pressure set), garden irrigation, etc. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 50
JSE
(from
1.5 t
o 3 H
P)
Flow rate up to 1�0 l/min (9.� m3/h)Head up to 9� m
They are recommended for pumping clean water and liquids that are chemi-cally non aggressive to the materials from which the pump is made. JSE self-priming pumps are designed for suction lifts and can be positioned above the water source, including applications with air entrained in the water. Due to their reliability and low maintenance, they are recommended for domestic use, including water distribution (as part of a pressure set), garden irrigation, etc. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 52
JET-S
S Flow rate up to 80 l/min (�.8 m3/h)Head up to 72 m
They are recommended for pumping clean water and liquids that are chemi-cally non aggressive to the materials from which the pump is made. JET-SS self-priming pumps are designed for suction lifts and can be positioned above the water source, including applications with air entrained in the water. Due to their reliability and low maintenance, they are recommended for domestic use, including water distribution (as part of a pressure set), garden irrigation, etc. The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 54
K
Flow rate up to �000 l/min (3�0 m3/h)Head up to 95 m
They are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. This series is suitable for supplying and moving water, in cooling, heating, circulating and conditioning systems, for fire fighting, irrigation, industrial and agricultural applications. Manifacture in accordance with dimensional standards EN 733 - DIN 24255 ensures models are fully interchangeable.The design allows the pump body to be removed without disconnecting it from the pipes (back pull out). The pumps must be installed in enclosed places, or at least protected against inclement weather.
Page 56
UTILI
TY Flow rate up to 50 l/min (3 m3/h)Head up to �7 m
Portable self-priming pumps capable of clearing entrained air from the suction pipe. Recommended for gardening, vegetable gardens, washing and hobby applications they are suitable for use with any liquids compatible with the materials of construction.
Page 74
PC P
UMP
Domestic pumps with a pressure sensing electronic controller for automatic operation; the pump operates as required as a tap is opened or closed. The controller also provides protection for the pump against dry running.
Page 77
BOOS
TER
SETS
Small pressure sets with vessel, for automatic operation. Suitable for the supply of pressurised water in the home or in holiday homes. Page 78
a complete line of electric water pumps...
...to satisfy any requirements
10
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 3.0 3.6 4.2 4.8 5.4Single-phase Three-phase kW HP 0 5 10 15 20 25 30 35 �0 50 �0 70 80 90
IP 500M IP 500 0.37 0.50
H metres
40 38 33.5 29 24 19.5 15 10 5IP 700M IP 700 0.50 0.70 55 50 45.5 40.5 36 31 27 22 17 8IP 800M IP 800 0.60 0.85 65 62 57 52 47 42 37 32 27 18IP 1000M IP 1000 0.75 1 70 66 61 56 51 46 41 36.5 31 22IP 900M IP 900 0.75 1 90 82 71 60 49 38 27 17 5
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 h3 i m n n1 w s 1~ 3~
IP 500M IP 500
1” 1”
42 243152 63
75 138
20
80 120 100 55
7
5.3 5.3
IP 700M IP 700 48 258/250 80 143 7.7 6.4
IP 800M IP 80055 285
179 7185 156
90 138 112 62
10.1 9.2
IP 1000M IP 100010.3
9.9
IP 900M IP 900 3/�” 3/�” 58 288 95 166 9.3
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
Q
H(m
)
IP900
IP1000IP800
IP700
IP500
pumps with peripheral impeller
IP
RANGE OF PERFORMANCEFlow rate up to 50 l/min (3.0 m3/h)Head up to 90 m
LIMITS OF USEManometric suction lift up to 8 mLiquid temperature up to + �0°CEnvironment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water without abrasive particles and liquids that are chemically non aggressive to the materials from which the pump is made.FOR THEIR RELIABILITY, SIMPLICITY OF USE AND ECONOMY THEY ARE SUITABLE FOR DOMESTIC USE AND IN PARTICULAR FOR DISTRIBUTING WATER IN COMBINATION WITH SMALL PRES-SURE SETS, FOR IRRIGATING GARDENS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS•PUMP BODY: cast iron, with threaded ports
ISO 228/1.•MOTOR BRACKET: aluminium with brass insert;
reduces starting difficulties due to seizure of the impeller after long periods of inactivity.
DIMENSIONS AND WEIGHTS
11
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
fDN2
DN1
a w ms
i
nn1
h3h2
h1
h
RANGE OF PERFORMANCEFlow rate up to 50 l/min (3.0 m3/h)Head up to 90 m
LIMITS OF USEManometric suction lift up to 8 mLiquid temperature up to + �0°CEnvironment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water without abrasive particles and liquids that are chemically non aggressive to the materials from which the pump is made.FOR THEIR RELIABILITY, SIMPLICITY OF USE AND ECONOMY THEY ARE SUITABLE FOR DOMESTIC USE AND IN PARTICULAR FOR DISTRIBUTING WATER IN COMBINATION WITH SMALL PRES-SURE SETS, FOR IRRIGATING GARDENS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS•PUMP BODY: cast iron, with threaded ports
ISO 228/1.•MOTOR BRACKET: aluminium with brass insert;
reduces starting difficulties due to seizure of the impeller after long periods of inactivity.
• IMPELLER: brass, of the type with radial periph-eral vanes.
•MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.•MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
IP M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
IP: three-phase 230/400 V - 50 Hz.• INSULATION: class F.•PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONS
12
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 3.0 3.6 4.2 4.8 5.4Single-phase Three-phase kW HP 0 5 10 15 20 25 30 35 �0 50 �0 70 80 90
IQ 500M IQ 500 0.37 0.50
H metres
40 38 33.5 29 24 19.5 15 10 5IQ 700M IQ 700 0.50 0.70 55 50 45.5 40.5 36 31 27 22 17 8IQ 800M IQ 800 0.60 0.85 65 62 57 52 47 42 37 32 27 18IQ 1000M IQ 1000 0.75 1 70 66 61 56 51 46 41 36.5 31 22IQ 1000HM IQ 1000H 0.75 1 90 82 71 60 49 38 27 17 5
TYPE PORTS DIMENSIONS mm kgSingle-phase Three-phase DN1 DN2 a f h h1 h2 h3 i m n n1 w s 1~ 3~
IQ 500M IQ 500
1” 1” 22
223152
108
30
13878 80 120 100
55
7
5.3 5.3IQ 700M IQ 700 234/227 113 143 57 7.1 6.3IQ 800M IQ 800
253 179 121 151 83 90 138 112 629.9 8.9
IQ 1000M IQ 1000 10.0 8.8IQ 1000HM IQ 1000H 3/�” 3/�” 22 253 179 126 27 153 84 90 138 112 62 10.0 9.0
Q
H(m
)
IQ1000
IQ800
IQ700
IQ500
IQ1000H
pumps with peripheral impeller
IQ
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 50 l/min (3.0 m3/h)Head up to 90 m
LIMITS OF USEManometric suction lift up to 8 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water without abrasive particles and liquids that are chemically non aggressive to the materials from which the pump is made.THE HYDRAULIC CHARACTERISTICS OF THESE PUMPS, TOGETHER WITH THEIR COMPACT-NESS, MAKE THEM SUITABLE FOR USE IN THE INDUSTRIAL SECTOR. The pumps must be installed in enclosed places, or at least protected against inclem-ent weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.•MOTOR BRACKET: aluminium with brass insert;
reduces starting difficulties due to seizure of the
impeller after long periods of inactivity.• IMPELLER: brass, of the type with radial periph-
eral vanes.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
IQ M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
IQ: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒ pump shaft in stainless steel EN 10088-3 - 1.��01 (AISI 31�)
DIMENSIONS AND WEIGHTS
13
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 50 l/min (3.0 m3/h)Head up to 90 m
LIMITS OF USEManometric suction lift up to 8 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water without abrasive particles and liquids that are chemically non aggressive to the materials from which the pump is made.THE HYDRAULIC CHARACTERISTICS OF THESE PUMPS, TOGETHER WITH THEIR COMPACT-NESS, MAKE THEM SUITABLE FOR USE IN THE INDUSTRIAL SECTOR. The pumps must be installed in enclosed places, or at least protected against inclem-ent weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.•MOTOR BRACKET: aluminium with brass insert;
reduces starting difficulties due to seizure of the
impeller after long periods of inactivity.• IMPELLER: brass, of the type with radial periph-
eral vanes.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
IQ M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
IQ: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒ pump shaft in stainless steel EN 10088-3 - 1.��01 (AISI 31�)
⇒special mechanical seal⇒protection IP 55⇒other voltages or frequency 60 Hz
DIMENSIONS
fDN2
i
DN1
w ms n1
n
h3
h1h2
h
a
1�
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.6 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.2 7.8 8.4 9.0 9.6Single-phase Three-phase kW HP 0 10 20 30 �0 50 �0 70 80 90 100 110 120 130 1�0 150 1�0
IC 50M IC 50 0.37 0.50
H metres
23 22 21 20 19 18 17 15.5 14IC 75M IC 75 0.55 0.75 33 32 31 29.5 28.5 27 25 23 19IC 100M IC 100 0.75 1 29.5 –– 29 28.5 28 27.5 26.5 26 24.5 23 21 18 15IC 100MH IC 100H 0.75 1 36 34 33.5 33 32.5 31.5 30 28.5 27 25IC 150M IC 150 1.1 1.5 41 –– –– 38 37 36 35 33.5 32 30 27.5 25 22IC 150LM IC 150L 1.1 1.5 36 –– –– 35 34.5 33.5 33 32 31 30 29 28 26.5 25 23 21 19IC 200M IC 200 1.5 2 50 –– –– 46 44.5 43 41.5 40 38 36 34.5 32.5 30.5 28 26––– IC 300 2.2 3 58 –– –– 55 54.5 53.5 52 51 49.5 48 46 44.5 42.5 40.5 38.5 36
14
TYPE PORTS DIMENSIONS mm kgSingle-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
IC 50M IC 50
1”
1”
42
259 205 82 123 165 135 41
10
7.8 7.6IC 75M IC 75
285 240 92 148 190 160 3811.5 11.5
IC 100M IC 100 12.5 11.3IC 100MH IC 100H 12.1 11.6IC 150M-150LM IC 150-150LL
11/�” 51367 260 110 150 206 165 44.5
1119.2 18.5
IC 200M IC 200364 290 115 175 242 206 32.5
25.0 24.2––– IC 300 - 25.5
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 1�0 l/min (9.� m3/h)Head up to 58 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Liquid temperature up to + �0°C in the ICX version (with technopolymer impeller) Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. RELIABLE AND MAINTENANCE FREE THEY ARE WIDELY USED IN THE DOMESTIC AND CIVIL SEC-TOR, IN PARTICULAR FOR WATER DISTRIBUTION IN COMBINATION WITH SMALL OR MEDIUM PRESSURE SETS, FOR TRANSFER IN GENERAL, FOR IRRIGATING GARDENS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.
• BODY BACK-PLATE: stainless steel AISI 30� or cast iron on higher
powered models.• BRASS IMPELLER: IC 75 - IC 100 - IC 150 - IC 200 - IC 300• STAINLESS STEEL IMPELLER: IC 50 - IC 100H• MOTOR SHAFT:
stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
IC M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
IC: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
DIMENSIONS AND WEIGHTS
IC100HIC 75
IC50
IC300
IC200
IC 150
IC150L
IC100
Q
H(m
)
centrifugal pumps
IC
15
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 1�0 l/min (9.� m3/h)Head up to 58 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Liquid temperature up to + �0°C in the ICX version (with technopolymer impeller) Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. RELIABLE AND MAINTENANCE FREE THEY ARE WIDELY USED IN THE DOMESTIC AND CIVIL SEC-TOR, IN PARTICULAR FOR WATER DISTRIBUTION IN COMBINATION WITH SMALL OR MEDIUM PRESSURE SETS, FOR TRANSFER IN GENERAL, FOR IRRIGATING GARDENS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.
• BODY BACK-PLATE: stainless steel AISI 30� or cast iron on higher
powered models.• BRASS IMPELLER: IC 75 - IC 100 - IC 150 - IC 200 - IC 300• STAINLESS STEEL IMPELLER: IC 50 - IC 100H• MOTOR SHAFT:
stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
IC M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
IC: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒ impeller in technopolymer (IC M...X - IC...X)⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONSf
aDN2
w
DN1
n
h
h1h2
n1s
1�
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 1.2 2.4 3.6 4.8 6.0 7.2 8.4 9.6
Single-phase Three-phase kW HP 0 20 �0 �0 80 100 120 1�0 1�0
IC 100 MSS IC 100 SS 0.75 1 H metres 23 21 20.5 20 18.5 17 15 13 10
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 h3 n n1 w s 1~ 3~
IC 100 MSS IC 100 SS 11/�” 1” 31.5 295 206 97 103 200 182 115 93 10 9.1 9.1
50 100 15075 125 17500
0
25
5 10
5
10
15
20
25
30
4321 6 7 8 9 11
0
feet
5 10 15 20 25 30 35 40 45
90
10
20
30
40
50
60
70
80
0
IC100SS
0 5 10 15 20 25 30 35 40
l/min
m /h3
54
=56%
51
53
Q
H(m
)
stainless steel centrifugal pump
IC-SS
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEMaximum flow rate 1�0 l/min (9.� m3/h)Maximum head 23 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°CEnvironment temperature up to + 55°C
INSTALLATION AND USEIt is recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THE CONSTRUCTION OF THESE CENTRIFUGAL PUMPS MAKES THEM SUITABLE FOR USE IN THE DOMES-TIC, AGRICULTURAL AND INDUSTRIAL SECTOR. ALL THE WETTED PARTS ARE IN STAINLESS STEEL AISI 30� TO GUARANTEE TOTAL HYGIENE AND MAXIMUM RESISTANCE TO CORROSION. The pump must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 30�, with
threaded ports ISO 228/1.• BODY BACK-PLATE AND DIFFUSER: AISI 30�.• IMPELLER: stainless steel AISI 30�, of the type
with centrifugal radial flow.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet running, totally enclosed fan cooled, suitable for continuous duty.
IC 100 MSS: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
IC 100 SS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
DIMENSIONS AND WEIGHTS
17
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEMaximum flow rate 1�0 l/min (9.� m3/h)Maximum head 23 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°CEnvironment temperature up to + 55°C
INSTALLATION AND USEIt is recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THE CONSTRUCTION OF THESE CENTRIFUGAL PUMPS MAKES THEM SUITABLE FOR USE IN THE DOMES-TIC, AGRICULTURAL AND INDUSTRIAL SECTOR. ALL THE WETTED PARTS ARE IN STAINLESS STEEL AISI 30� TO GUARANTEE TOTAL HYGIENE AND MAXIMUM RESISTANCE TO CORROSION. The pump must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 30�, with
threaded ports ISO 228/1.• BODY BACK-PLATE AND DIFFUSER: AISI 30�.• IMPELLER: stainless steel AISI 30�, of the type
with centrifugal radial flow.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet running, totally enclosed fan cooled, suitable for continuous duty.
IC 100 MSS: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
IC 100 SS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒version in stainless steel EN 10088-3 - 1.��01
(AISI 31�)⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONSf
DN1
a
h
h2h1
h3
n
DN2
w n1s
18
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 250 l/min (15 m3/h)Head up to 57 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THE PUMPS IN THIS SERIES ARE MADE TO STANDARDS EN 733 - DIN 2�255 AND ARE SPECIFICALLY USED IN THE CIVIL, INDUSTRIAL OR AGRICULTURAL SECTORS WHERE THEIR CHARACTERISTICS OF STURDINESS AND RELI-ABILITY CAN BE BEST APPRECIATED. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, made to standards
EN 733 - DIN 24255 and UNI 7467- NF E-44-111, with threaded ports ISO 228/1.
DIMENSIONS AND WEIGHTS
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.5 8.4 9.6 10.8 12.0 13.2 15.0Single-phase Three-phase kW HP 0 50 �0 70 80 90 100 110 125 1�0 1�0 180 200 220 250
ICn 150BM/1�0 ICn 150B/1�0 1.1 1.5
H metres
33 32.5 32 31.5 31 30.5 30 29 28 26.5 24 21.5 18ICn 200AM/1�0 ICn 200A/1�0 1.5 2 38 37 36.8 36.5 36 35.5 35 34 33 31.5 29.5 27 24 20––– ICn 300AR/1�0 2.2 3 42 41 41 40.5 40 39.5 39 38 37 36 34 31 28 24ICn 300BM/200 ICn 300B/200 2.2 3 49 48 47.5 47 46.5 45.5 45 44 43 41 38.5 36 32 28 22––– ICn �00A/200 3 4 57 56 55.8 55.5 55 54.5 53.5 53 52 50.5 48.5 46 43.5 40 33
Q
H(m
)
ICn 400A/200
ICn 150B/160
ICn 200A/160
ICn 300AR/160
ICn 300B/200
standardised centrifugal pumps to “EN 733 - DIN 2�255”
ICn
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w1 w2 s 1~ 3~
ICn 150BM/1�0 ICn 150B/1�0
11/2” 1”
56 386 260 105 155 206 150 27.5 27.5 10
20.7 18.7
ICn 200AM/1�0 ICn 200A/1�0 21.7 21.0
––– ICn 300AR/1�0 - 21.8
ICn 300BM/200 ICn 300B/20060
384/359305 125 180 252 210 23.5 39.5 11
31.0 28.6
––– ICn �00A/200 384 - 30.7
19
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 250 l/min (15 m3/h)Head up to 57 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THE PUMPS IN THIS SERIES ARE MADE TO STANDARDS EN 733 - DIN 2�255 AND ARE SPECIFICALLY USED IN THE CIVIL, INDUSTRIAL OR AGRICULTURAL SECTORS WHERE THEIR CHARACTERISTICS OF STURDINESS AND RELI-ABILITY CAN BE BEST APPRECIATED. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, made to standards
EN 733 - DIN 24255 and UNI 7467- NF E-44-111, with threaded ports ISO 228/1.
• IMPELLER: brass, of the type with centrifugal radial flow.
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
ICn M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector up to 1.5 kW.
ICn: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONS
fa
DN2
DN1
w1
n
n1
hh2
h1
sw2
20
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to �00 l/min (3� m3/h)Head up to 39 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USETHE ICH SERIES IS RECOMMENDED FOR CIVIL, AGRICULTURAL AND INDUSTRIAL APPLICA-TIONS. THE HIGH FLOW RATES AND CONTINU-OUS RATING MAKE IT IDEAL FOR IRRIGATION WITH FLOWING AND SPRINKLING WATER, FOR DRAWING WATER FROM LAKES, RIVERS, WELLS, OR FOR INDUSTRIAL APPLICATIONS THAT NEED TO ACHIEVE LARGE FLOW RATES AT MEDIUM-LOW HEADS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• IMPELLER:
brass, of the type with centrifugal radial flow.
DIMENSIONS AND WEIGHTS
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 3 6 9 12 15 18 21 24 30 36Single-phase Three-phase kW HP 0 50 100 150 200 250 300 350 �00 500 �00
ICH 50M ICH 50 0.37 0.50
H metres
9 8.5 8.2 7.5 6.3 4.9 2.8ICH 75M ICH 75 0.55 0.75 12 11.5 11.2 10.6 9.6 8 6ICH 80M ICH 80 0.60 0.85 18.2 17.2 16 14 11.5 9 5.4ICH 100M ICH 100 0.75 1 21.2 20.2 19 17 14.5 11.6 8.4ICH 150M ICH 150 1.1 1.5 29 28 26.5 24.5 22 18.5 15ICH 200M ICH 200 1.5 2 33 32 30.5 28.5 26 22.5 19––– ICH 300 2.2 3 39 38 36.5 34.5 32 28.5 25ICH 80CM ICH 80C 0.60 0.85 12.5 - 12 11.7 11 10.2 9.2 8 6.5ICH 100BM ICH 100B 0.75 1 13.7 - 13.2 13 12.5 11.6 10.5 9.2 8 5ICH 150AM ICH 150A 1.1 1.5 14.5 - 13.8 13.5 13.2 12.6 11.8 10.5 9.2 6.5 3ICH 150BM ICH 150B 1.1 1.5 20.2 - 19.2 19 18 17 16 14 12 7.5ICH 200AM ICH 200A 1.5 2 22.5 - 22 21.5 21 20 18.5 16.6 14.5 10
Q
H(m
)
ICH 300
ICH 200
ICH 150
ICH 100
ICH 80
ICH 75
ICH 50
ICH 150AICH 100B
ICH 80C
ICH 200A
ICH 150B
centrifugal pumps - medium flow rates
ICH
TYPE PORTS DIMENSIONS mm kgSingle-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
ICH 50M ICH 50
11/2” 11/2”
45
276200 82 118 165 135 1
10
8.3 8.2ICH 75M ICH 75 283/276 8.9 8.4ICH 80M ICH 80
300 225 92 133 190 160 415.5 15.1
ICH 100M ICH 100 13.0 12.1ICH 150M ICH 150
48.5 373 269 114 155 216 171 12 1220.0 19.3
ICH 200M ICH 200 22.2 21.6––– ICH 300 - 22.8ICH 80CM ICH 80C
2” 2”60 332 238 97 141 196
16014
11
15.3 14.2ICH 100BM ICH 100B 15.1 14.3ICH 150AM ICH 150A 15.5 15.2ICH 150BM ICH 150B
51 386 260 110 150 206 120.3 19.5
ICH 200AM ICH 200A 22.2 21.8
21
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to �00 l/min (3� m3/h)Head up to 39 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USETHE ICH SERIES IS RECOMMENDED FOR CIVIL, AGRICULTURAL AND INDUSTRIAL APPLICA-TIONS. THE HIGH FLOW RATES AND CONTINU-OUS RATING MAKE IT IDEAL FOR IRRIGATION WITH FLOWING AND SPRINKLING WATER, FOR DRAWING WATER FROM LAKES, RIVERS, WELLS, OR FOR INDUSTRIAL APPLICATIONS THAT NEED TO ACHIEVE LARGE FLOW RATES AT MEDIUM-LOW HEADS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• IMPELLER:
brass, of the type with centrifugal radial flow.
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled to
a carefully matched electric motor, quiet running, totally enclosed fan cooled, suitable for continuous duty.
ICH M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
ICH: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONSf
na
DN2
w
DN1
h2
n1
h1h
s
22
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 12 18 24 30 36 42 48 54 60 66 72 84 96 102 108 120 132Single-phase Three-phase kW HP 0 200 300 �00 500 �00 700 800 900 1000 1100 1200 1�00 1�00 1700 1800 2000 2200
ICH100/�M ICH100/� 0.75 1
H metres
10 9.3 8.7 8 7 6 4.7 3ICH150/�CM ICH150/�C 1.1 1.5 11.9 11.7 11.3 10.7 10.2 9.2 8 6.7 5 3ICH200/�BM ICH200/�B 1.5 2 14.7 14.5 14 13.5 12.8 12 11 9.7 8.2 6.7 5––– ICH300/�A 2.2 3 18.5 18.1 17.8 17.2 16.8 16 15 13.8 12.2 10.5 8.3 6ICH150/�CRM ICH150/�CR 1.1 1.5 11.9 11.7 11.3 10.7 10.2 9.2 8 6.7 5 3ICH200/�BRM ICH200/�BR 1.5 2 14.7 14.5 14 13.5 12.8 12 11 9.7 8.2 6.7 5––– ICH300/�AR 2.2 3 18.5 18.1 17.8 17.2 16.8 16 15 13.8 12.2 10.5 8.3 6ICH�00/8BM ICH�00/8B 3 4 21.5 21 20.7 20 19.5 18.8 17.8 16.5 15 13.5 11.2 9––– ICH550/8A 4 5.5 24.5 24 23.5 23 22.5 21.8 20.8 19.5 18.3 16.8 15 13ICH�00/20BM ICH�00/20B 3 4 16 - - 15.5 15.4 15.3 15.2 15 14.5 14 13 12 9 4.8 2––– ICH550/20A 4 5.5 19 - - 18.5 18.4 18.3 18.2 18 17.5 17 16.2 15.2 12 7.8 5 2––– ICH750/30B 5.5 7.5 18 - - - - 18 18 18 18 18 17.5 17 16.5 15.5 15 14.5 13––– ICH1000/30A 7.5 10 23 - - - - 23 23 23 23 23 22.5 22.5 22.5 22 21.5 21 19.5 18
100
Q
H(m
)
ICH 550/8A
ICH 400/8B
ICH 300/6A
ICH 200/6B
ICH 150/6C
ICH 100/4
ICH 550/20A
ICH 400/20B
ICH 1000/30A
ICH 750/30B
centrifugal pumps - high flow rates
ICH
TYPE PORTS DIMENSIONS mm kgSingle-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
ICH100/�M ICH100/� 21/2” 21/2” 55 323 240 97 143 190 155 0 10 15.6 14.2ICH150/�CM ICH150/�C
3” 3” 68 411
312
120 192 240
190
6 12
28.1 26.2ICH200/�BM ICH200/�B 29.1 28.5––– ICH300/�A - 29.4ICH150/�CRM ICH150/�CR
�” �”
70 41329.7 29.2
ICH200/�BRM ICH200/�BR 32.0 31.4––– ICH300/�AR - 32.3ICH�00/8BM ICH�00/8B
80
429
132 180 24530 14
41.0 36.1––– ICH550/8A 462 - 41.0ICH�00/20BM ICH�00/20B 429 40.5 35.3––– ICH550/20A 462 - 40.5––– ICH750/30B
82 585 370 160 210 292 212- 60.9
––– ICH1000/30A - 65.2
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 1800 l/min (108 m3/h)Head up to 2�.5 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USETHE ICH SERIES IS RECOMMENDED FOR USE IN THE CIVIL, AGRICULTURAL AND INDUSTRIAL FIELD. THE HIGH FLOW RATES AND CONTINU-OUS RATING MAKE IT IDEAL FOR IRRIGATION WITH FLOWING AND SPRINKLING WATER, FOR DRAWING WATER FROM LAKES, RIVERS, WELLS, OR FOR INDUSTRIAL APPLICATIONS THAT NEED TO ACHIEVE LARGE FLOW RATES AT MEDIUM-LOW HEADS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• IMPELLER: brass (cast iron for ICH/30), of the
type with centrifugal radial flow.
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
ICH M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
ICH: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONS AND WEIGHTS
23
fa
DN2
DN1
w
n
n1
h2h1
h
s
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 1800 l/min (108 m3/h)Head up to 2�.5 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C
INSTALLATION AND USETHE ICH SERIES IS RECOMMENDED FOR USE IN THE CIVIL, AGRICULTURAL AND INDUSTRIAL FIELD. THE HIGH FLOW RATES AND CONTINU-OUS RATING MAKE IT IDEAL FOR IRRIGATION WITH FLOWING AND SPRINKLING WATER, FOR DRAWING WATER FROM LAKES, RIVERS, WELLS, OR FOR INDUSTRIAL APPLICATIONS THAT NEED TO ACHIEVE LARGE FLOW RATES AT MEDIUM-LOW HEADS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• IMPELLER: brass (cast iron for ICH/30), of the
type with centrifugal radial flow.
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
ICH M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
ICH: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONS
2�
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 3 6 9 12 15 18 19.5 21
Single-phase Three-phase kW HP 0 50 100 150 200 250 300 325 350
NCO 75M NCO 75 0.55 0.75H metres
18 17 16 14.5 13 10.5 8 6NCO 100M NCO 100 0.75 1 20 19.5 18 16.5 15 12.5 10 8 6
Q
H(m
)
NCO100
NCO75
centrifugal pumps with open impeller
NCO
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 350 l/min (21 m3/h)Head up to 20 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°CLiquid temperature up to + �0°C in the NCOX version (with technopolymer impeller)Environment temperature up to + �0°C Passage of solid bodies Ø 10 mm
INSTALLATION AND USEThey are recommended for pumping water and liquids that are chemically non aggressive to the materials from which the pump is made. THE OPEN IMPELLER DESIGN ALLOWS THE PUMPING OF LIQUIDS WITH RELATIVELY HIGH LEVELS OF IMPURITIES WITHOUT RISK OF CLOGGING THE IMPELLER. FOR THIS REASON THE NCO SERIES ARE SUITABLE FOR USE IN INDUSTRY, FOR THE TRANSFER OF WATER FROM CANALS, RIVERS, RESERVOIRS, TANKS, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• OPEN IMPELLER: stainless steel AISI 31�.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.NCO M: single-phase 230V-50 Hz with capacitor and thermal overload protector.NCO: three-phase 230/400 V - 50 Hz.
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
NCO 75M NCO 7511/2” 11/2” 41 297 227 92 135 190 160 50 10
12.7 11.8
NCO 100M NCO 100 12.8 11.9
DIMENSIONS AND WEIGHTS
25
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 350 l/min (21 m3/h)Head up to 20 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°CLiquid temperature up to + �0°C in the NCOX version (with technopolymer impeller)Environment temperature up to + �0°C Passage of solid bodies Ø 10 mm
INSTALLATION AND USEThey are recommended for pumping water and liquids that are chemically non aggressive to the materials from which the pump is made. THE OPEN IMPELLER DESIGN ALLOWS THE PUMPING OF LIQUIDS WITH RELATIVELY HIGH LEVELS OF IMPURITIES WITHOUT RISK OF CLOGGING THE IMPELLER. FOR THIS REASON THE NCO SERIES ARE SUITABLE FOR USE IN INDUSTRY, FOR THE TRANSFER OF WATER FROM CANALS, RIVERS, RESERVOIRS, TANKS, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• OPEN IMPELLER: stainless steel AISI 31�.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.NCO M: single-phase 230V-50 Hz with capacitor and thermal overload protector.NCO: three-phase 230/400 V - 50 Hz.
• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒ impeller in technopolymer
(NCO M...X - NCO...X)⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONSf
a
DN1
DN2
w n1
h1h2
h
s
n
2�
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 3 6 9 12 15 18 19.5 21Single-phase Three-phase kW HP 0 50 100 150 200 250 300 325 350
PRO-NCO 75M PRO-NCO 75 0.55 0.75H metres
18 17 16 14.5 13 10.5 8 6PRO-NCO 100M PRO-NCO 100 0.75 1.00 20 19.5 18 16.5 15 12.5 10 8 6
Q
H(m
)
PRO-NCO 100
PRO-NCO 75
stainless steel pumps
PRO-NCO
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 350 l/min (21 m3/h)Head up to 20 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C Passage of solid bodies Ø 10 mm
INSTALLATION AND USEThey are recommended for pumping water and liquids that are chemically non aggressive to the materials from which the pump is made. THE OPEN IMPELLER DESIGN ALLOWS THE PUMPING OF LIQUIDS WITH RELATIVELY HIGH LEVELS OF IMPURITIES WITHOUT RISK OF CLOGGING THE IMPELLER. FOR THIS REASON THE PRO-NCO SERIES ARE SUITABLE FOR USE IN SYSTEMS FOR WASHING FRUIT, VEGETABLES, FISH, SHELLFISH, MEAT, IN INDUSTRIAL SYSTEMS FOR WASHING METAL PARTS, GLASS CONTAINERS, AND FOR THE CIRCULATION OF COOLING LIQUIDS.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 31�, with
threaded ports ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 31�.• OPEN IMPELLER: stainless steel AISI 31�.• MOTOR SHAFT: stainless steel AISI 31�.• MECHANICAL SEAL: ceramic - graphite - viton - AISI 31�•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.PRO-NCO M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.PRO-NCO: three-phase 230/400 V - 50 Hz.
• INSULATION: class F. •PROTECTION: IP 44.
TYPE PORTS kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
PRO-NCO 75M PRO-NCO 7511/2” 11/2” 41 297 227 92 135 190 160 50 10
13.0 12.0
PRO-NCO 100M PRO-NCO 100 13.1 12.1
DIMENSIONS AND WEIGHTS
27
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 350 l/min (21 m3/h)Head up to 20 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Environment temperature up to + �0°C Passage of solid bodies Ø 10 mm
INSTALLATION AND USEThey are recommended for pumping water and liquids that are chemically non aggressive to the materials from which the pump is made. THE OPEN IMPELLER DESIGN ALLOWS THE PUMPING OF LIQUIDS WITH RELATIVELY HIGH LEVELS OF IMPURITIES WITHOUT RISK OF CLOGGING THE IMPELLER. FOR THIS REASON THE PRO-NCO SERIES ARE SUITABLE FOR USE IN SYSTEMS FOR WASHING FRUIT, VEGETABLES, FISH, SHELLFISH, MEAT, IN INDUSTRIAL SYSTEMS FOR WASHING METAL PARTS, GLASS CONTAINERS, AND FOR THE CIRCULATION OF COOLING LIQUIDS.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 31�, with
threaded ports ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 31�.• OPEN IMPELLER: stainless steel AISI 31�.• MOTOR SHAFT: stainless steel AISI 31�.• MECHANICAL SEAL: ceramic - graphite - viton - AISI 31�•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.PRO-NCO M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.PRO-NCO: three-phase 230/400 V - 50 Hz.
• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz⇒protection IP 55
DIMENSIONSf
a
DN1
DN2
w n1
n
h1h2
h
s
28
ICB 200ICB 150HICB 100N
ICB 300AICB 200BICB 150M
ICB 1000A/32ICB 750B/32ICB 550B/32ICB 400C/32
ICB 1000A/40ICB 750B/40ICB 550C/40
Q
H(m
)
H(fe
et)
two stage centrifugal pumps
ICB
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to �00 l/min (2� m3/h)Head up to 112 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Liquid temperature up to + �0°C in the ICBX version (with technopolymer impeller) Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THEIR HIGH EFFICIENCY AND ADAPTABILITY TO THE MOST VARIED, EVEN UNUSUAL APPLICA-TIONS, MAKE THEM THE IDEAL CHOICE IN THE DOMESTIC, CIVIL AND INDUSTRIAL FIELD; IN PARTICULAR FOR DISTRIBUTING WATER IN COMBINATION WITH PRESSURE SETS, FOR INCREASING PRESSURE IN THE MAINS, FOR FIRE-FIGHTING SETS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL:
ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, with high efficiency (class EFF1 for powers from � to 7.5
kW), quiet running, totally enclosed fan cooled, suitable for continuous duty.
ICB M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector (up to 1.5 kW).
ICB: three-phase 230/400 V - 50 Hz up to 4 kW. 400/690 V - 50 Hz from 5.5 to 7.5 kW.• INSULATION: class F. •PROTECTION: IP 44.
ICB 100N• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• IMPELLERS: stainless steel AISI 30� of the type
with centrifugal radial flow.
Other ICB • PUMP BODY: cast iron, with threaded ports
ISO 228/1.• IMPELLERS:brass, of the type with centrifugal
radial flow.
OPTIONS ON REQUEST⇒ impeller in technopolymer
(ICB M...X - ICB...X)
Two stage pumps recognised for their high efficiency, versatility and quiet running.
29
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
RANGE OF PERFORMANCEFlow rate up to �00 l/min (2� m3/h)Head up to 112 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + 90°C Liquid temperature up to + �0°C in the ICBX version (with technopolymer impeller) Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THEIR HIGH EFFICIENCY AND ADAPTABILITY TO THE MOST VARIED, EVEN UNUSUAL APPLICA-TIONS, MAKE THEM THE IDEAL CHOICE IN THE DOMESTIC, CIVIL AND INDUSTRIAL FIELD; IN PARTICULAR FOR DISTRIBUTING WATER IN COMBINATION WITH PRESSURE SETS, FOR INCREASING PRESSURE IN THE MAINS, FOR FIRE-FIGHTING SETS. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL:
ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, with high efficiency (class EFF1 for powers from � to 7.5
kW), quiet running, totally enclosed fan cooled, suitable for continuous duty.
ICB M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector (up to 1.5 kW).
ICB: three-phase 230/400 V - 50 Hz up to 4 kW. 400/690 V - 50 Hz from 5.5 to 7.5 kW.• INSULATION: class F. •PROTECTION: IP 44.
ICB 100N• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• IMPELLERS: stainless steel AISI 30� of the type
with centrifugal radial flow.
Other ICB • PUMP BODY: cast iron, with threaded ports
ISO 228/1.• IMPELLERS:brass, of the type with centrifugal
radial flow.
OPTIONS ON REQUEST⇒ impeller in technopolymer
(ICB M...X - ICB...X)
Two stage pumps recognised for their high efficiency, versatility and quiet running.
⇒special mechanical seal⇒other voltages or frequency 60 Hz
30
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
ICB200
ICB100N
ICB150H
ICB200ICB100NICB150H
ICB200
ICB100N
ICB150H
two stage centrifugal pumps
ICB
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6Single-phase Three-phase kW HP 0 20 30 �0 50 �0 70 80 90 100 110
ICB 100NM ICB 100N 0.75 1H metres
42 39 37 34 31 28.5 25.5 22 18 15ICB 150HM ICB 150H 1.1 1.5 54 53 51 49 46 42 38 34 29 24ICB 200M ICB 200 1.5 2 66 64 62 60 57 53 49 44 39.5 35 30
31
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
ICB300A
ICB200B
ICB150M
ICB150M ICB200B ICB300A
ICB150M
ICB200B
ICB300A
two stage centrifugal pumps
ICB
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.5 8.4 9.6 10.8Single-phase Three-phase kW HP 0 20 30 �0 50 �0 70 80 90 100 110 125 1�0 1�0 180
ICB 150MM ICB 150M 1.1 1.5H metres
47 46 45.5 44 43 42 41 38 36 34 31 27 22ICB 200BM ICB 200B 1.5 2 58 56 55 54 53 52 50 48 46 44 41 37 33 26––– ICB 300A 2.2 3 68 66.5 65.5 65 63 62 60 58 56 54 51 47 42 35 28
32
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
ICB550B/32
ICB400C/32
ICB550B/32
ICB400C/32
two stage centrifugal pumps
ICB
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.5 8.4 9.6 10.8 12.0 15.0Single-phase Three-phase kW HP 0 �0 50 �0 70 80 90 100 110 125 1�0 1�0 180 200 250
ICB �00C/32M ICB �00C/32 3 4H metres
70 66.5 65.5 65 64 63 62 60.5 59 57 55 52 49.5 46.5 36––– ICB 550B/32 4 5.5 85 81 80 79 78 77 76 75 74 72 69 66 62 58 49
33
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
ICB1000A/32
ICB750B/32
ICB1000A/32
ICB750B/32
two stage centrifugal pumps
ICB
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
POWER m3/hl/min
0 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.5 8.4 9.6 10.8 12.0 15.0Three-phase kW HP 0 �0 50 �0 70 80 90 100 110 125 1�0 1�0 180 200 250
ICB 750B/32 5.5 7.5H metres
94 94 93.5 93 92 91 90 89 87 85 83 79 75 70 56ICB 1000A/32 7.5 10 112 111 110.8 110.5 110.3 110 109 108 107 105 102 99 94 89 74
3�
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
ICB1000A/40
ICB750B/40
ICB550C/40
ICB550C/40 ICB1000A/40ICB750B/40
ICB550C/40
ICB1000A/40
ICB750B/40
two stage centrifugal pumps
ICB
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 6.0 6.6 7.5 8.4 9.6 10.8 12.0 15.0 18.0 21.0 24.0Three-phase kW HP 0 100 110 125 140 160 180 200 250 300 350 400
ICB 550C/�0 4 5.5H metres
64 62 61 60 59 58 56 54.5 49 43 35ICB 750B/�0 5.5 7.5 76 73 72.5 72 71 70 69 67.5 64 59.5 54 46ICB 1000A/�0 7.5 10 88 85 84.5 84 83 82 81 79.5 76 72 67 60
35
DIMENSIONS AND WEIGHTS
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
ICB 100NM ICB 100N
11/�”
1”
73 330 201 92 109 180 142 110
14.5 14.0
ICB 150HM ICB 150H 74 382 225 93 132 200 162 23 20.1 19.4
ICB 200M ICB 200 84 405 263 110 153 225 185 26 11 24.8 24.1
ICB 150MM ICB 150M
11/2”
74 382 225 93 132 200 162 23 10 20.1 19.2
ICB 200BM ICB 200B86 407 263 110 153 225 185 26 11
24.6 25.2
––– ICB 300A - 26.1
ICB �00C/32M ICB �00C/32
11/�”
95 464 304 132 172 266 206 19
14
42.9 39.1
––– ICB 550B/32 - 42.9
––– ICB 750B/32
2” 108
542
334 139 195 292 232 21
- 56.0
––– ICB 1000A/32 - 61.7
––– ICB 550C/�0
11/2”
496 - 49.8
––– ICB 750B/�0542
- 55.1
––– ICB 1000A/�0 - 60.8
two stage centrifugal pumps
ICB
f
a
DN1
DN2
w n1
h1h2
h
s
n
3�
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.2 7.8Single-phase Three-phase kW HP 0 5 10 15 20 25 30 �0 50 �0 70 80 90 100 110 120 130
MSG 05M MSG 05 0.37 0.50
H metres
27 26 25 24 22.5 21 20 16.5 13 9 5MSG 07M MSG 07 0.45 0.60 38 36 35 34 33.5 31 29 25 20 15.5 10 5MSG 08M MSG 08 0.60 0.85 50 48 47 45 43 40.5 38.5 33.5 28 22.5 16 10MSG 08LM MSG 08L 0.60 0.85 36 35.5 35 34 33.5 32.5 32 30 28 26 23 20 17 13.5 10 5MSG 10M MSG 10 0.75 1 46 45 44 43 42 41 40 38 35.5 33 30 26.5 22.5 19 15 10 5
H(m
)
MSG08
MSG10
MSG08LMSG07
MSG05
Q
multi-stage centrifugal pumps
MSG
RANGE OF PERFORMANCEFlow rate up to 130 l/min (7.8 m3/h)Head up to 50 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. DUE TO THEIR RELIABILITY, QUIET RUNNING AND LOW MAINTENANCE, THEY ARE SUITABLE FOR DOMESTIC APPLICATIONS INCLUDING WA-TER SUPPLIES (AS A PRESSURE SET), GARDEN IRRIGATION, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• IMPELLERS: of the type with centrifugal radial
flow, made of technopolymer (approved for drinking water).
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
MSG M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
MSG: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
MSG 05M MSG 05
1” 1”
110 334
172134
38158 116 2 9
8.6 8.6
MSG 07M MSG 07 9.4 8.9
MSG 08M MSG 08 135 367/359 10.8 10.2
MSG 08LM MSG 08L 110 342/334 10.2 9.4
MSG 10M MSG 10 135 378 191 61 13.4 12.3
DIMENSIONS AND WEIGHTS
37
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1 CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 130 l/min (7.8 m3/h)Head up to 50 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. DUE TO THEIR RELIABILITY, QUIET RUNNING AND LOW MAINTENANCE, THEY ARE SUITABLE FOR DOMESTIC APPLICATIONS INCLUDING WA-TER SUPPLIES (AS A PRESSURE SET), GARDEN IRRIGATION, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• IMPELLERS: of the type with centrifugal radial
flow, made of technopolymer (approved for drinking water).
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
MSG M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
MSG: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
DIMENSIONS
fa
DN1
DN2
w
n
hh2
h1
n1s
38
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.2Single-phase Three-phase kW HP 0 5 10 15 20 25 30 �0 50 �0 70 80 90 100 110 120
MS 07M MS 07 0.45 0.60H metres
38 36 35 34 32.5 31 29 25 20 15.5 10 5MS 08M MS 08 0.60 0.85 50 48 47 45 43 40.5 38.5 33.5 28 22.5 16 10MS 08LM MS 08L 0.60 0.85 36 35.5 35 34 33.5 32.5 32 30 28 25.5 23 20 17 13.5 10 5
Q
H(m
)
MS08
MS07
MS08L
multi-stage centrifugal pumps
MS 07-08
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 120 l/min (7.2 m3/h)Head up to 50 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made.DUE TO THEIR RELIABILITY AND QUIET RUN-NING, THEY ARE SUITABLE FOR DOMESTIC AP-PLICATIONS INCLUDING WATER SUPPLIES (AS A PRESSURE SET), GARDEN IRRIGATION, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 30�, with
threaded ports ISO 228/1.• BODY BACK-PLATE:
stainless steel AISI 30�.• IMPELLERS: of the type with centrifugal radial
flow, made of technopolymer (approved for
drinking water).• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
MS M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
MS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
MS 07M MS 07
1” 1” 90
345
174 122 52 160 120 95 9
6.9 6.3
MS 08M MS 08353/345
7.6 6.9
MS 08LM MS 08L 7.5 6.9
stainless steel pump body
DIMENSIONS AND WEIGHTS
39
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 120 l/min (7.2 m3/h)Head up to 50 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made.DUE TO THEIR RELIABILITY AND QUIET RUN-NING, THEY ARE SUITABLE FOR DOMESTIC AP-PLICATIONS INCLUDING WATER SUPPLIES (AS A PRESSURE SET), GARDEN IRRIGATION, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 30�, with
threaded ports ISO 228/1.• BODY BACK-PLATE:
stainless steel AISI 30�.• IMPELLERS: of the type with centrifugal radial
flow, made of technopolymer (approved for
drinking water).• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
MS M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
MS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
fa
DN1
DN2
w
n
n1s
hh2
h1
DIMENSIONS
�0
TYPE POWER m3/hl/min
0 0.6 1.2 1.8 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8Single-phase Three-phase kW HP 0 10 20 30 �0 �5 50 55 �0 �5 70 75 80
VMS A 0�M ––– 0.45 0.6
H metres
36 35 33 31 28 26 25 23 22 20 18 16 14VMS A 07M ––– 0.55 0.75 48 46 44 41 37.5 35 34 31 29 26 23 19.5 16VMS A 10M VMS A 10 0.75 1 60 58 55 51 47 44 42 38 36 32 28 23 18VMS A 15M VMS A 15 1.1 1.5 75 72 70 66 61 58 55 52 48 44 40 35 30VMS A 20M VMS A 20 1.5 2 90 87 83 78 73 70 66 62 58 53 48 44 38VMS A 25M VMS A 25 1.8 2.5 105 102 98 92 85 82 78 73 68 63 57 50 45
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
Q
H(m
)
VMS A25
VMS A20
VMS A15
VMS A10
VMS A07
VMS A06
vertical multi-stage pumps
VMS A
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to to the materials from which the pump is made. THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL APPLICATIONS. BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET ENVIRONMENTS AND IN SPACES WITH INSUFFICIENT VENTILATION.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stain-
less steel AISI 30� case with threaded ports ISO 228-1.
• IMPELLERS AND DIFFUSERS: technopolymer.• DIAPHRAGMS: stainless steel AISI 30�, com-
plete with anti-wear rings.
• MOTOR SHAFT: stainless steel EN 10088-3 -1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty. VMS A M: single-phase 220÷240 V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMS A: three-phase 380÷415 V - 50 Hz.•INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMS A M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug VMS A: (three-phase)•2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
TYPE PORTS N° DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 stages a b c d f h h1 h2 n w1 w2 s 1~ 3~
VMS A 0�M –––
11/�”
11/�”
3
90
81 200 66 223
432
50
382
183 62 88.5 11
10.9 -
VMS A 07M ––– 4 506 456 13.0 -
VMS A 10M VMS A 105
530 480 16.3 14.8
VMS A 15M VMS A 15
11/2” 100
603
60
543 24.1 22.4
VMS A 20M VMS A 20 6 633 573 25.0 23.4
VMS A 25M VMS A 25 7 708 648 30.8 26.7
DIMENSIONS AND WEIGHTS
RANGE OF PERFORMANCEFlow rate up to 80 l/min (�.8 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
�1
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to to the materials from which the pump is made. THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL APPLICATIONS. BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET ENVIRONMENTS AND IN SPACES WITH INSUFFICIENT VENTILATION.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stain-
less steel AISI 30� case with threaded ports ISO 228-1.
• IMPELLERS AND DIFFUSERS: technopolymer.• DIAPHRAGMS: stainless steel AISI 30�, com-
plete with anti-wear rings.
• MOTOR SHAFT: stainless steel EN 10088-3 -1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty. VMS A M: single-phase 220÷240 V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMS A: three-phase 380÷415 V - 50 Hz.•INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMS A M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug VMS A: (three-phase)•2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
DIMENSIONS
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 80 l/min (�.8 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
VMSVMS
w1n
w1
h
a
DN1
h2h1
w2
f
w2
DN2
s
SINGLE-PHASE CONTROL BOX
c
b d
�2
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.2Single-phase Three-phase kW HP 0 20 30 �0 50 �0 70 80 90 100 110 120
VMS B 0�M ––– 0.45 0.6
H metres
30 27 26 25 24 22.5 20.5 18 15.5 13 10 7VMS B 07M ––– 0.55 0.75 40 37 36 34.5 32.5 30 28 25 21.5 18.5 14.5 10VMS B 10M VMS B 10 0.75 1 50 48 46 44 41 38 35 32 28 24 19 14VMS B 15M VMS B 15 1.1 1.5 60 56 54 52 50 48 46 43 39 36 31 24VMS B 20M VMS B 20 1.5 2 75 72 69 66 64 60 57 53 48 43 38 32VMS B 25M VMS B 25 1.8 2.5 90 85 83 79 76 73 68 64 58 52 44 38VMS B 30M VMS B 30 2.2 3 105 101 98 94 90 86 80 75 67 60 52 44
Q
H(m
)
VMS B30
VMS B25
VMS B20
VMS B15
VMS B10
VMS B07
VMS B06
vertical multi-stage pumps
VMS B
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made.THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL APPLICATIONS, BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET ENVIRONMENTS AND IN SPACES WITH INSUFFICIENT VENTILATION.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stain-
less steel AISI 30� case with threaded ports ISO 228-1.
• IMPELLERS AND DIFFUSERS: technopolymer.• DIAPHRAGMS: stainless steel AISI 30�, com-
plete with anti-wear rings.
• MOTOR SHAFT: stainless steel EN 10088-3-1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty. VMS B M: single-phase 220÷240 V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMS B: three-phase 380÷415 V-50 Hz.•INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMS B M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug VMS B: (three-phase) •2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
TYPE PORTS N° DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 stages a b c d f h h1 h2 n w1 w2 s 1~ 3~
VMS B 0�M –––
11/�”
11/�”
3
90
81 200 66 223
432
50
382
183 62 88.5 11
10.9 -
VMS B 07M ––– 4 506 456 13.0 -
VMS B 10M VMS B 10 5 530 480 16.3 14.8
VMS B 15M VMS B 15
11/2”
4
100
573
60
513 23.0 21.0
VMS B 20M VMS B 20 5 603 543 24.1 22.4
VMS B 25M VMS B 25 6 633 573 25.0 23.4
VMS B 30M VMS B 30 7 708 648 30.7 26.7
DIMENSIONS AND WEIGHTS
RANGE OF PERFORMANCEFlow rate up to 120 l/min (7.2 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
�3
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made.THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL APPLICATIONS, BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET ENVIRONMENTS AND IN SPACES WITH INSUFFICIENT VENTILATION.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stain-
less steel AISI 30� case with threaded ports ISO 228-1.
• IMPELLERS AND DIFFUSERS: technopolymer.• DIAPHRAGMS: stainless steel AISI 30�, com-
plete with anti-wear rings.
• MOTOR SHAFT: stainless steel EN 10088-3-1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty. VMS B M: single-phase 220÷240 V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMS B: three-phase 380÷415 V-50 Hz.•INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMS B M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug VMS B: (three-phase) •2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
DIMENSIONS
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 120 l/min (7.2 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
VMSVMS
w1n
w1
h
a
DN1
h2h1
w2f
w2
DN2
s
SINGLE-PHASE CONTROL BOX
c
b d
��
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.6 1.2 1.8 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8Single-phase Three-phase kW HP 0 10 20 30 �0 �5 50 55 �0 �5 70 75 80VMSE A 0�M ––– 0.45 0.6
H metres
36 35 33 31 28 26 25 23 22 20 18 16 14VMSE A 07M ––– 0.55 0.75 48 46 44 41 37.5 35 34 31 29 26 23 19.5 16VMSE A 10M VMSE A 10 0.75 1 60 58 55 51 47 44 42 38 36 32 28 23 18VMSE A 15M VMSE A 15 1.1 1.5 75 72 70 66 61 58 55 52 48 44 40 35 30VMSE A 20M VMSE A 20 1.5 2 90 87 83 78 73 70 66 62 58 53 48 44 38VMSE A 25M VMSE A 25 1.8 2.5 105 102 98 92 85 82 78 73 68 63 57 50 45
Q
H(m
)
VMSEA25
VMSEA20
VMSEA15
VMSEA10
VMSEA07M
VMSEA06M
“in-line” multi-stage pumps
VMSE A
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL AP-PLICATIONS AND, BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET AREAS AND IN SPACES WITH INSUFFICIENT VENTILATION. THE ENCLOSED DESIGN ALSO ELIMINATES THE POSSIBILITY OF WATER ESCAP-ING AS A RESULT OF SEAL FAILURE, MAKING IT SUITABLE FOR USE IN CARPETED OR OTHER DELICATE ENVIRONMENTS. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stainless
steel AISI 30� case with threaded ports ISO 228-1.• IMPELLERS AND DIFFUSERS: technopolymer.
• DIAPHRAGMS: stainless steel AISI 30�, com-plete with anti-wear rings.
• MOTOR SHAFT: stainless steel EN 10088-3 -1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty.VMSE A M: single-phase 220÷240 V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMSE A: three-phase 380÷415 V-50Hz.• INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMSE A M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug.VMSE A: (three-phase) •2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒ other voltages or frequency 60 Hz
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN N° stages Ø h a b c 1~ 3~
VMSE A 0�M –––
11/�”
3
135
397
81 200 66
8.4 -
VMSE A 07M ––– 4 471 10.5 -
VMSE A 10M VMSE A 105
495 13.8 12.3
VMSE A 15M VMSE A 15
153
547 20.6 18.9
VMSE A 20M VMSE A 20 6 577 21.5 19.9
VMSE A 25M VMSE A 25 7 652 27.3 23.2
RANGE OF PERFORMANCEMaximum flow rate 80 l/min (�.8 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
DIMENSIONS AND WEIGHTS
�5
VMSE
VMSE
VMSE
VMSE
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL AP-PLICATIONS AND, BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET AREAS AND IN SPACES WITH INSUFFICIENT VENTILATION. THE ENCLOSED DESIGN ALSO ELIMINATES THE POSSIBILITY OF WATER ESCAP-ING AS A RESULT OF SEAL FAILURE, MAKING IT SUITABLE FOR USE IN CARPETED OR OTHER DELICATE ENVIRONMENTS. GUARANTEE 2 YEARS subject to our general terms of sale. CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stainless
steel AISI 30� case with threaded ports ISO 228-1.• IMPELLERS AND DIFFUSERS: technopolymer.
• DIAPHRAGMS: stainless steel AISI 30�, com-plete with anti-wear rings.
• MOTOR SHAFT: stainless steel EN 10088-3 -1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty.VMSE A M: single-phase 220÷240 V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMSE A: three-phase 380÷415 V-50Hz.• INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMSE A M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug.VMSE A: (three-phase) •2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒ other voltages or frequency 60 Hz
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEMaximum flow rate 80 l/min (�.8 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
DN2
h
ØDN1
ØDN2
DN1
h
Vertical installation Horizontal installation
SINGLE-PHASE CONTROL BOX
b
a c
DIMENSIONS
��
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0 6.6 7.2Single-phase Three-phase kW HP 0 20 30 �0 50 �0 70 80 90 100 110 120
VMSE B 0�M ––– 0.45 0.6
H metres
30 27 26 25 24 22.5 20.5 18 15.5 13 10 7VMSE B 07M ––– 0.55 0.75 40 37 36 34.5 32.5 30 28 25 21.5 18.5 14.5 10VMSE B 10M VMSE B 10 0.75 1 50 48 46 44 41 38 35 32 28 24 19 14VMSE B 15M VMSE B 15 1.1 1.5 60 56 54 52 50 48 46 43 39 36 31 24VMSE B 20M VMSE B 20 1.5 2 75 72 69 66 64 60 57 53 48 43 38 32VMSE B 25M VMSE B 25 1.8 2.5 90 85 83 79 76 73 68 64 58 52 44 38VMSE B 30M VMSE B 30 2.2 3 105 101 98 94 90 86 80 75 67 60 52 44
Q
H(m
)
VMSEB30
VMSEB07M
VMSEB10
VMSEB15
VMSEB20
VMSEB25
VMSEB06M
“in-line” multi-stage pumps
VMSE B
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL APPLICATIONS AND, BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET AREAS AND IN SPACES WITH INSUFFICIENT VENTILATION. THE ENCLOSED DESIGN ALSO ELIMINATES THE POSSIBILITY OF WATER ESCAPING AS A RESULT OF SEAL FAILURE, MAKING IT SUITABLE FOR USE IN CARPETED OR OTHER DELICATE ENVIRONMENTS.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stain-
less steel AISI 30�, case with threaded ports ISO 228-1.
• IMPELLERS AND DIFFUSERS: technopolymer.• DIAPHRAGMS: stainless steel AISI 30�, com-
plete with anti-wear rings.• MOTOR SHAFT:
stainless steel EN 10088-3 - 1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty. VMSE B M: single-phase 220÷240V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMSE B: three-phase 380÷415 V-50Hz.• INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMSE B M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug. VMSE B: (three-phase) •2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN N° stages Ø h a b c 1~ 3~
VMSE B 0�M –––
11/�”
3
135
397
81 200 66
8.4 -
VMSE B 07M ––– 4 471 10.5 -
VMSE B 10M VMSE B 10 5 495 13.8 12.3
VMSE B 15M VMSE B 15 4
153
517 19.5 17.5
VMSE B 20M VMSE B 20 5 547 20.6 18.9
VMSE B 25M VMSE B 25 6 577 21.5 19.9
VMSE B 30M VMSE B 30 7 652 27.2 23.2
RANGE OF PERFORMANCEMaximum flow rate 120 l/min (7.2 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
DIMENSIONS AND WEIGHTS
�7
VMSE
VMSE
VMSE
VMSE
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THEIR RELIABILITY AND QUIET RUNNING MAKE THEM SUITABLE FOR DOMESTIC AND CIVIL APPLICATIONS AND, BECAUSE THE PUMP IS FULLY SUBMERSIBLE WITH THE MOTOR COOLED BY THE PUMPED LIQUID, IT CAN BE USED SAFELY IN WET AREAS AND IN SPACES WITH INSUFFICIENT VENTILATION. THE ENCLOSED DESIGN ALSO ELIMINATES THE POSSIBILITY OF WATER ESCAPING AS A RESULT OF SEAL FAILURE, MAKING IT SUITABLE FOR USE IN CARPETED OR OTHER DELICATE ENVIRONMENTS.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• OUTER CASE AND MOTOR SUPPORT: stain-
less steel AISI 30�, case with threaded ports ISO 228-1.
• IMPELLERS AND DIFFUSERS: technopolymer.• DIAPHRAGMS: stainless steel AISI 30�, com-
plete with anti-wear rings.• MOTOR SHAFT:
stainless steel EN 10088-3 - 1.�10�.• DOUBLE SEAL: mechanical seal silicon car-
bide-ceramic-NBR, with oil barrier chamber and inner lip seal to protect the seal in the event of dry running.
• SCREWS: stainless steel AISI 30�.•MOTOR: electric, asynchronous for continuous
duty. VMSE B M: single-phase 220÷240V - 50 Hz with
thermal overload protector built into windings below 1.5 kW. The 1.8 kW motor has an external overload protector (with manual reset) incorpo-rated into the control box.
VMSE B: three-phase 380÷415 V-50Hz.• INSULATION: class F. •PROTECTION: IP 68.
STANDARD FEATURES:VMSE B M: (single-phase) •2 m power cable type “H07 RN-F” with removable
connector.•Control box with capacitor and Schuko plug. VMSE B: (three-phase) •2 m power cable type “H07 RN-F” with removable
connector.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEMaximum flow rate 120 l/min (7.2 m3/h)Head up to 105 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature up to + �0°C
DN2
h
ØDN1
ØDN2
DN1
h
Vertical installation Horizontal installation
SINGLE-PHASE CONTROL BOX
b
a c
DIMENSIONS
�8
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0
Single-phase Three-phase kW HP 0 5 10 15 20 25 30 35 �0 �5 50
JS 05M JS 05 0.37 0.50
H metres
35 32 27 24 21 19 17 16 15 14 13
JS 07M JS 07 0.50 0.70 41 36 31 27 24 22 20 19 17 16 15
JS 08M JS 08 0.60 0.85 47 42 38 34 31 28.5 26 24 22 21.5 19
Q
H(m
)
JS08
JS07
JS05
“JET” self-priming pumpsJS
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 50 l/min (3 m3/h)Head up to �7 m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JS SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1. • BODY BACK-PLATE: stainless steel AISI 30�.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: brass.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL:
ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JS M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 h3 n n1 w s 1~ 3~
JS 05M JS 05
1” 1” 115379
171 127 33.5 160.5 160 124 24 10
9.3 9.1
JS 07M JS 07 10.0 9.5
JS 08M JS 08 387/379 10.2 10.1
DIMENSIONS AND WEIGHTS
�9
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 50 l/min (3 m3/h)Head up to �7 m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JS SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1. • BODY BACK-PLATE: stainless steel AISI 30�.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: brass.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL:
ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JS M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒impeller in technopolymer (JS M..X - JS...X)⇒other voltages or frequency 60 Hz
DIMENSIONS
fa
w
DN1
h1h3
h2
n
n1
h
s
DN2
50
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.4 2.7 3.0 3.6 4.2 4.8Single-phase Three-phase kW HP 0 5 10 15 20 25 30 �0 �5 50 �0 70 80
JS 10HM JS 10H 0.75 1
H metres
56 51 47 44 41 39 36 32 30 28JS 12HM JS 12H 0.90 1.25 64 58 54 51 48 45 43 38 36 34JS 15HM JS 15H 1.1 1.5 70 66 62 58 54 51 48 43 41 38JS 10LM JS 10L 0.75 1 46 42 40 38 37 35 33 30 29 27 25 23 21JS 12LM JS 12L 0.90 1.25 50 48 46 44 42 41 39 36 35 33 31 29 27JS 15LM JS 15L 1.1 1.5 55 52 50 48 46 45 43 40 39 37 35 33 30
Q
H(m
)
JS15H
JS12H
JS10H
JS15L
JS12L
JS10L
“JET” self-priming pumps
JS
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 80 l/min (�.8 m3/h)Head up to 70 m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JS SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1. • BODY BACK-PLATE: stainless steel AISI 30�.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: brass.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite -NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JS M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 h3 n n1 w s 1~ 3~
JS 10HM JS 10H
1” 1” 113.5 402 201 147 35 182 180 142 22 10
13.7 13.8
JS 12HM JS 12H 15.0 14.0
JS 15HM JS 15H 15.2 14.2
JS 10LM JS 10L 13.7 13.8
JS 12LM JS 12L 15.0 14.0
JS 15LM JS 15L 15.2 14.2
DIMENSIONS AND WEIGHTS
51
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 80 l/min (�.8 m3/h)Head up to 70 m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JS SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1. • BODY BACK-PLATE: stainless steel AISI 30�.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: brass.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite -NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JS M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JS: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒impeller in technopolymer (JS M...X - JS...X)⇒other voltages or frequency 60 Hz
DIMENSIONS
fa
DN2
h3h1
DN1
w
n
n1s
h
h2
52
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.6 4.2 4.8 6.0 7.2 8.4 9.6Single-phase Three-phase kW HP 0 10 15 20 25 30 35 �0 �5 50 �0 70 80 100 120 1�0 1�0
JSE 15HM JSE 15H 1.1 1.5
H metres
64 60 55 51 48 45 42.5 40 39 37 34 31JSE 20HM JSE 20H 1.5 2 76 70 67 64 61 58 55.5 53 51 49 45 41 39––– JSE 30H 2.2 3 96 90 86 82 79 75 71.5 69 66 64 58 54 50JSE 15MM JSE 15M 1.1 1.5 52 50 48 45 44 42 40 38 37 35 32 29 27 23 20JSE 20MM JSE 20M 1.5 2 60 58 56 54 52 51 49 47 46 45 42 39 37 33 30––– JSE 30M 2.2 3 74 70 68 67 65 63 61 59 58 56 54 51 49 44 40JSE 15LM JSE 15L 1.1 1.5 42 40 39 38 37 36 35 34 33 32 30 28 26 23 20 17 15JSE 20LM JSE 20L 1.5 2 51 48 46 45 44 43 42 41 40 39 37 35 33 30 27 24 22––– JSE 30L 2.2 3 62 60 58 57 56 55 54 53 52 51 49 47 45 42 39 36.5 35
Q
H(m
)
JSE 30H
JSE 20H
JSE 15H
JSE 15M
JSE 20M
JSE 30M
JSE 15L
JSE 20L
JSE 30L
“JET” self-priming pumps
JSE
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 1�0 l/min (9.� m3/h)Head up to 9� m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JSE SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1. • BODY BACK-PLATE: cast iron.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: brass.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JSE M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JSE: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 h3 n n1 w s 1~ 3~
JSE 15HM JSE 15H
11/�” 1” 155 523 242 165 43 208 206 164 30 11
25.4 23.5
JSE 20HM JSE 20H 26.5 25.7
––– JSE 30H - 26.8
JSE 15MM JSE 15M 25.4 23.5
JSE 20MM JSE 20M 26.5 25.7
––– JSE 30M - 26.8
JSE 15LM JSE 15L 25.4 23.5
JSE 20LM JSE 20L 26.5 25.7
––– JSE 30L - 26.8
DIMENSIONS AND WEIGHTS
53
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 1�0 l/min (9.� m3/h)Head up to 9� m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JSE SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC. The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, with threaded ports
ISO 228/1. • BODY BACK-PLATE: cast iron.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: brass.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JSE M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JSE: three-phase 230/400 V - 50 Hz.• INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒special mechanical seal⇒other voltages or frequency 60 Hz
DIMENSIONS
f
w
h3h1
h2
an
n1 s
h
DN2
DN1
5�
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 3.0 3.6 4.2 4.8Single-phase Three-phase kW HP 0 5 10 15 20 25 30 35 �0 50 �0 70 80
JET 05MSS JET 05SS 0.37 0.50
H metres
35 32 27 24 21 19 17 16 15 13JET 07MSS JET 07SS 0.50 0.70 41 36 31 27 24 22 20 19 17 15JET 08MSS JET 08SS 0.60 0.85 47 42 38 34 31 28.5 26 24 22 19JET 10HMSS JET 10HSS 0.75 1 56 50 45 41 37 33 30 27 25 22JET 12HMSS JET 12HSS 0.90 1.25 64 58 53 48 44 40 36 33 31 26JET 15HMSS JET 15HSS 1.1 1.5 72 67 61 56 51 47 43 40 37 32JET 10LMSS JET 10LSS 0.75 1 46 44 41 39 37 35 32 30 28 25 22 21 19JET 12LMSS JET 12LSS 0.90 1.25 50 48 45 43 41 39 37 36 34 30 27 25 23JET 15LMSS JET 15LSS 1.1 1.5 55 53 50 48 46 43 41 39 37 34 31 29 27
Q
H(m
)
JET 15HSS
JET 12HSS
JET 10HSS
JET 08HSS
JET 07HSS
JET 05MSS
JET 15LSS
JET 12LSS
JET 10LSS
“JET” self-priming pumps
JET-SS
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 80 l/min (�.8 m3/h)Head up to 72 m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JET-SS SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 30�, with
threaded ports ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: technopolymer (for drinking water).• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10� • MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JET MSS: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JET SS: three-phase 230/400 V - 50 Hz.•INSULATION: class F. •PROTECTION: IP 44.
TYPE PORTS DIMENSIONS mm kg
Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 w s 1~ 3~
JET 05MSS JET 05SS
1” 1” 90345
174 122 52 160 120 95 9
5.6 5.8
JET 07MSS JET 07SS 5.7 6.0
JET 08MSS JET 08SS 353/345 6.9 6.5
JET 10HMSS-LMSS JET 10HSS-LSS
11/�” 1” 117 406 206 145 55 184 135 110 10
9.4 9.6
JET 12HMSS-LMSS JET 12HSS-LSS 10.5 9.6
JET 15HMSS-LMSS JET 15HSS-LSS 10.8 10.4
DIMENSIONS AND WEIGHTS
stainless steel pump body
55
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
RANGE OF PERFORMANCEFlow rate up to 80 l/min (�.8 m3/h)Head up to 72 m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. JET-SS SELF-PRIMING PUMPS ARE DESIGNED FOR SUCTION LIFTS AND CAN BE POSITIONED ABOVE THE WATER SOURCE, INCLUDING APPLICATIONS WITH AIR ENTRAINED IN THE WATER. DUE TO THEIR RELIABILITY AND LOW MAINTENANCE, THEY ARE RECOMMENDED FOR DOMESTIC USE, INCLUDING WATER DISTRIBUTION (AS PART OF A PRESSURE SET), GARDEN IRRIGATION, ETC.The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: stainless steel AISI 30�, with
threaded ports ISO 228/1.• BODY BACK-PLATE: stainless steel AISI 30�.• EJECTOR ASSEMBLY: technopolymer (approved for drinking water).• IMPELLER: technopolymer (for drinking water).• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10� • MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, quiet run-ning, totally enclosed fan cooled, suitable for continuous duty.
JET MSS: single-phase 230 V - 50 Hz with capacitor and thermal overload protector.
JET SS: three-phase 230/400 V - 50 Hz.•INSULATION: class F. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒other voltages or frequency 60 Hz
DIMENSIONS
h
DN1
h1
fa
DN2
w
n
n1s
h2
5�
20
H(m
)
H(fe
et)
K40/250
Q
K50/250
K50/200
K32/200
K32/200HK40/200
K32/160
K50/160K65/160
K65/200
K65/125
K40/160
K80/160
K100/60
K50/125
standardised centrifugal pumps to EN 733 - DIN 2�255
K
RANGE OF PERFORMANCEFlow rate up to �000 l/min (3�0 m3/h)Head up to 95 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature from -10°C to + 90°C Environment temperature from -10°C to + �0°C Max. pressure in the pump body 10 bar (PN10)
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THIS SERIES IS SUITABLE FOR SUPPLYING AND MOVING WATER, IN COOLING, HEATING, CIR-CULATING AND CONDITIONING SYSTEMS, FOR FIRE FIGHTING, IRRIGATION, INDUSTRIAL AND AGRICULTURAL APPLICATIONS.Manifacture in accordance with dimensional standards EN 733 - DIN 2�255 ensures models are fully interchangeable. The design allows the pump body to be removed without disconnecting it from the pipes (back pull out). The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, complies with dimension-
al standards EN 733 - DIN 24255 and UNI 7467-NF E-44-111, with flanged suction and delivery ports complete with threaded steel counterflanges.
• BODY BACK-PLATE: cast iron.• IMPELLER: brass for models K32/160, K32/200,
K40/160, K40/200, K50/125 and K50/160.• IMPELLER: cast iron for models K40/250,
K50/200, K50/250, K65/125, K65/160, K65/200, K80/160, K100/160
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.• ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, asynchro-nous type with high efficiency (class EFF1 for powers from � to 22 kW), quiet running, totally enclosed fan cooled, suitable for continuous duty.
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
57
RANGE OF PERFORMANCEFlow rate up to �000 l/min (3�0 m3/h)Head up to 95 m
LIMITS OF USEManometric suction lift up to 7 mLiquid temperature from -10°C to + 90°C Environment temperature from -10°C to + �0°C Max. pressure in the pump body 10 bar (PN10)
INSTALLATION AND USEThey are recommended for pumping clean water and liquids that are chemically non aggressive to the materials from which the pump is made. THIS SERIES IS SUITABLE FOR SUPPLYING AND MOVING WATER, IN COOLING, HEATING, CIR-CULATING AND CONDITIONING SYSTEMS, FOR FIRE FIGHTING, IRRIGATION, INDUSTRIAL AND AGRICULTURAL APPLICATIONS.Manifacture in accordance with dimensional standards EN 733 - DIN 2�255 ensures models are fully interchangeable. The design allows the pump body to be removed without disconnecting it from the pipes (back pull out). The pumps must be installed in enclosed places, or at least protected against inclement weather.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS• PUMP BODY: cast iron, complies with dimension-
al standards EN 733 - DIN 24255 and UNI 7467-NF E-44-111, with flanged suction and delivery ports complete with threaded steel counterflanges.
• BODY BACK-PLATE: cast iron.• IMPELLER: brass for models K32/160, K32/200,
K40/160, K40/200, K50/125 and K50/160.• IMPELLER: cast iron for models K40/250,
K50/200, K50/250, K65/125, K65/160, K65/200, K80/160, K100/160
• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.• ELECTRIC MOTOR: the pumps are close-coupled
to a carefully matched electric motor, asynchro-nous type with high efficiency (class EFF1 for powers from � to 22 kW), quiet running, totally enclosed fan cooled, suitable for continuous duty.
K M: single-phase 230 V - 50 Hz with capacitor and thermal overload protector (up to 1.5 kW).
K: three-phase 230/400 V - 50 Hz up to 4 kW. 400/690 V - 50 Hz from 5.5 to 22 kW.•INSULATION: classe K. •PROTECTION: IP 44.
OPTIONS ON REQUEST⇒pump shaft in stainless steel EN 10088-3 - 1.��01 (AISI 31�)⇒special mechanical seal⇒other voltages or frequency 60 Hz⇒protection IP 55⇒for liquids with higher or lower temperatures⇒for environments with higher or lower tempera-
tures
CONSTRUCTION AND SAFETY STANDARDSEN �003�-1IEC 3�-1CEI 2-3
58
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K32/160A
K32/160C
K32/160B
K32/160A
K32/160C
K32/160B
DN1= 50 DN2= 32
K 32/160
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 6 9 12 15 18 21 24 27
Single-phase Three-phase kW HP 0 100 150 200 250 300 350 �00 �50
K 32/1�0CM K 32/1�0C 1.5 2
H metres
25 24 23 21 19 16 13
K 32/1�0BM K 32/1�0B 2.2 3 31 30 29 28 26 23.5 20 16
K 32/1�0AM K 32/1�0A 3 4 38 37 36 34 32 30 27.5 24 20
59
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K32/200A
K32/200B
K32/200C
K32/200A
K32/200B
K32/200C
K 32/200
DN1= 50 DN2= 32
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 6 9 12 15 18 21 24 27 30
Three-phase kW HP 0 100 150 200 250 300 350 �00 �50 500
K 32/200C 4 5.5
H metres
46 44 43 41.5 40 38 36 34 31.5
K 32/200B 5.5 7.5 54 52 50.5 49 47 45 43 41 38.5 36
K 32/200A 7.5 10 60 57 56.5 56 55 53 52 50 47 44
�0
K32/200AH
K32/200BH
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K32/200AH
K32/200BH
K 32/200H
DN1= 50 DN2= 32
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 6 9 12 15 18
Single-phase Three-phase kW HP 0 100 150 200 250 300
K 32/200BHM K 32/200BH 3 4H metres
49 45 42 39 34 28
––– K 32/200AH 4 5.5 59 55 52 49 44 38
�1
K40/160A
K40/160B
K40/160C
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K40/160A
K40/160B
K40/160C
K 40/160
DN1= �5 DN2=�0
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 6 9 12 15 18 24 30 36 42
Single-phase Three-phase kW HP 0 100 150 200 250 300 �00 500 �00 700
K �0/1�0CM K �0/1�0C 2.2 3
H metres
27 27 26.5 26 25.5 25 22.5 19 14
K �0/1�0BM K �0/1�0B 3 4 32 32 31.5 31 30.5 30 27.5 24 20
––– K �0/1�0A 4 5.5 38 38 37.8 37 36.5 36 33.5 30 26 20
�2
K40/200A
K40/200B
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K40/200A
K40/200B
K 40/200
DN1= �5 DN2= �0
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 6 9 12 15 18 24 30 36 42
Three-phase kW HP 0 100 150 200 250 300 �00 500 �00 700
K �0/200B 5.5 7.5H metres
48 47 46.5 46 45.5 44.5 42 38 34 28
K �0/200A 7.5 10 56 55 55 55 54.5 54 52.5 49.5 46 41
�3
K40/250A
K40/250B
K40/250C
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K40/250A
K40/250B
K40/250C
K 40/250
DN1= �5 DN2= �0
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 6 9 12 15 18 24 30 36 42
Three-phase kW HP 0 100 150 200 250 300 �00 500 �00 700
K �0/250C 9.2 12.5
H metres
64 64 63.5 63 62.5 62 60 56.5 52.5 47
K �0/250B 11 15 71 71 70.5 70 69.5 69 67 64 60 55
K �0/250A 15 20 88 88 87.5 87 86.5 86 84 81 77 72
��
K50/125A
K50/125B
K50/125C
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K50/125A
K50/125B
K50/125C
K 50/125
DN1= �5 DN2= 50
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 18 24 30 36 42 48 54 60 66 72
Single-phase Three-phase kW HP 0 300 �00 500 �00 700 800 900 1000 1100 1200
K 50/125CM K 50/125C 2.2 3
H metres
18.5 17.5 17 16.5 15.5 14.8 13.5 12 10.5 8.2 6
K 50/125BM K 50/125B 3 4 21.5 20.7 20 19.5 18.8 17.8 16.5 15 13.5 11.2 9
––– K 50/125A 4 5.5 24.5 23.5 23 22.5 21.8 20.8 19.5 18.3 16.8 15 13
�5
K50/160A
K50/160B
K50/160C
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K50/160A
K50/160B
K50/160C
K 50/160
DN1= �5 DN2= 50
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 18 24 30 36 42 48 54 60 66
Three-phase kW HP 0 300 �00 500 �00 700 800 900 1000 1100
K 50/1�0C 4 5.5
H metres
27 27 26.5 25 24.5 23 20 18.5 16
K 50/1�0B 5.5 7.5 33 32 31.7 31 30 29 27 26 24 21
K 50/1�0A 7.5 10 38 37 36.8 36.5 36 34 33 32 30 27
��
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K50/200AR
K50/200A
K50/200B
K50/200C
K50/200AR
K50/200A
K50/200B
K50/200C
K 50/200
DN1= �5 DN2= 50
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
24 36 48 60 72 84 96 102 108
Three-phase kW HP �00 �00 800 1000 1200 1�00 1�00 1700 1800
K 50/200C 11 15
H metres
44 44 44 42 39 36 33 30
K 50/200B 15 20 52 52 52 50 47 44 40 38
K 50/200A 18.5 25 61 61 60.5 60 57 54 50 48 45
K 50/200AR 22 30 69 69 68.5 68 65 62 58 56 53
�7
K50/250AR
K50/250DK50/250C
K50/250B
K50/250A
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K50/250AR
K50/250D
K50/250C
K50/250B
K50/250A
K 50/250
DN1= �5 DN2= 50
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 18 24 30 36 42 48 54 60
Three-phase kW HP 0 300 �00 500 �00 700 800 900 1000
K 50/250D 9.2 12.5
H metres
51 51 49 47 44 41 37 32
K 50/250C 11 15 59 59 58 57 54 51 47 42
K 50/250B 15 20 72 72 71 70 69 67 65 62 59
K 50/250A 18.5 25 85 85 84 83 82 80 78 76 73
K 50/250AR 22 30 95 95 94 93 92 90 88 86 83
�8
K65/125A
K65/125B
K65/125C
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K65/125A
K65/125B
K65/125C
K 65/125
DN1= 80DN2= �5
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 36 48 60 72 84 96 108 120 132
Three-phase kW HP 0 �00 800 1000 1200 1�00 1�00 1800 2000 2200
K �5/125C 4 5.5
H metres
16 16 16 15.5 14.5 13.5 12.5 11
K �5/125B 5.5 7.5 18 18 18 18 17 16.5 15.5 14.5 13
K �5/125A 7.5 10 23 23 23 23 22.5 22.5 22 21 19.5 18
�9
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K65/160A
K65/160B
K65/160C
K65/160A
K65/160B
K65/160C
K 65/160
DN1= 80DN2= �5
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 36 48 60 72 84 96 108 120 132 144
Three-phase kW HP 0 �00 800 1000 1200 1�00 1�00 1800 2000 2200 2�00
K �5/1�0C 9.2 12.5
H metres
32 32 32 32 32 30 29 27 25 22
K �5/1�0B 11 15 37 36.5 36.5 36 35.5 34 33 31 29 26 23
K �5/1�0A 15 20 41 40.5 40.5 40 39.5 39 37.5 36 34 31 28
70
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K65/200AR
K65/200A
K65/200B
K65/200AR
K65/200A
K65/200B
K 65/200
DN1= 80DN2= �5
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
24 36 48 60 72 84 96 108 120 126
Three-phase kW HP �00 �00 800 1000 1200 1�00 1�00 1800 2000 2100
K �5/200B 15 20
H metres
45 45 45 45 44 42.5 41 38.5 35.5
K �5/200A 18.5 25 51 51 51 51 50 49 47 44.5 41.5 40
K �5/200AR 22 30 57 57 57 57 56 55 53 50.5 47.5 46
71
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K80/160A
K80/160B
K80/160C
K80/160D
K80/160A
K80/160B
K80/160C
K80/160D
K 80/160
DN1=100DN2= 80
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 30 60 90 120 150 180 210 240
Three-phase kW HP 0 500 1000 1500 2000 2500 3000 3500 �000
K 80/1�0D 11 15
H metres
25 25 25 24.5 23.5 21 18 14.5 10
K 80/1�0C 15 20 30 30 30 29.5 28.5 26 23 19.5 15
K 80/1�0B 18.5 25 35 35 35 34.5 33.5 31 28 24.5 20
K 80/1�0A 22 30 40 40 40 39.5 38.5 36 33 29.5 25
72
K100/160A
K100/160B
K100/160C
Q
(m)
H(m
)
H(fe
et)
NP
SH(m
)P
2(k
W)
NP
SH(fe
et)
P2
(HP)
K100/160A
K100/160B
K100/160C
K 100/160
DN1= 125DN2= 100
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
TYPE POWER m3/hl/min
0 60 120 180 240 270 300 330 360
Three-phase kW HP 0 1000 2000 3000 �000 �500 5000 5500 �000
K 100/1�0C 15 20
H metres
28 28 25.5 22 17.5 15 12
K 100/1�0B 18.5 25 32 32 30 27 22.5 19.5 17 13
K 100/1�0A 22 30 35 35 34 31 27 24.5 22 18 15
73
DIMENSIONS AND WEIGHTS
TYPE PORTS DIMENSIONS mm kg*Single-phase Three-phase DN1 DN2 a f h h1 h2 n n1 n2 w1 w2 s 1~ 3~
K32/1�0CM K32/1�0C
50 32
80
412292 132 160 242
190 24035 35
14
39.2 38.4K32/1�0BM K32/1�0B 431/412 42.6 39.2K32/1�0AM K32/1�0A 465/431 - 42.6––– K 32/200C 469
340 160 180 270
- 52.1––– K 32/200B 515 - 57.0––– K 32/200A - 63.0K 32/200BHM K 32/200BH 469 52.8 48.5––– K 32/200AH - 52.8K �0/1�0CM K �0/1�0C
�5 �0
431/412292 132 160 240
43.9 41.2K �0/1�0BM K �0/1�0B 465/431 50.5 43.9––– K �0/1�0A 465 - 50.5––– K �0/200B
100
535 340 160 180 275 212 265 - 61.4––– K �0/200A - 65.9––– K �0/250C 606 405 180 225 328 250 320 47.5 47.5
- 108.0––– K �0/250B - 115.0––– K �0/250A 701 - 132.0K 50/125CM K 50/125C
�5 50
450/431292 132 160 242 190 240
35 35
44.2 41.4K 50/125BM K 50/125B 484/450 50.5 44.2––– K 50/125A 484 - 50.5––– K 50/1�0C 489
340
160
180 269
212 265
- 55.5––– K 50/1�0B 535 - 60.5––– K 50/1�0A - 65.0––– K 50/200C 616
360 200 316
- 105.3––– K 50/200B 711 - 121.7––– K 50/200A - 134.2––– K 50/200AR 743 - 145.7––– K 50/250D 606
405 180 225 337 250 320
47.5 47.5
- 111.0––– K 50/250C - 118.0––– K 50/250B 701 - 135.0––– K 50/250A - 148.0––– K 50/250AR 733 - 159.5––– K �5/125C
80 �5
511340
160
180 291
212 280
- 62.0––– K �5/125B 557 - 67.7––– K �5/125A - 72.0––– K �5/1�0C 621 360 200 300
- 100.0––– K �5/1�0B - 107.0––– K �5/1�0A 716 - 123.0––– K �5/200B 719
405 180 225
340
250 320
- 128.0––– K �5/200A - 141.5––– K �5/200AR 751 - 153.0––– K 80/1�0D
100 80
125
652
330
- 112.5––– K 80/1�0C 747 - 129.5––– K 80/1�0B - 142.5––– K 80/1�0A 779 - 154.0––– K 100/1�0C
125 100 758 480 200 280 362 280 360 60 60 18- 141.2
––– K 100/1�0B - 153.7––– K 100/1�0A 790 - 165.2
(*weight includes counterflanges)
f
w1 w2
DN1
aDN2
n
n1n2
hh2
h1
s
DN DN
tu
tu
DN FLANGES t u HOLESmm mm mm Nº Ø (mm)
32 1�0 100
�
18
�0 150 11050 1�5 125�5 185 1�580 200 1�0
8100 220 180125 250 210
7�7�
portable self-priming pumps
UTILITY
RANGE OF PERFORMANCEFlow rate up to 50 l/min (3 m3/h)Head up to �7 m
LIMITS OF USEManometric suction lift up to 9 mLiquid temperature up to + �0°C Environment temperature up to + �0°C
INSTALLATION AND USEPORTABLE SELF-PRIMING PUMPS CAPABLE OF CLEARING ENTRAINED AIR FROM THE SUCTION PIPE. RECOMMENDED FOR GARDENING, VEGETABLE GARDENS, WASHING AND HOBBY APPLICA-TIONS THEY ARE SUITABLE FOR USE WITH ANY LIQUIDS COMPATIBLE WITH THE MATERIALS OF CONSTRUCTION.
GUARANTEE 2 YEARS subject to our general terms of sale.
CONSTRUCTION CHARACTERISTICS•PUMP BODY UTILITY 05M,07M,08M:
cast iron; •PUMP BODY UTILITY 05MSS, 07MSS, 08MSS: stainless steel AISI 30�.• IMPELLER: technopolymer, centrifugal type.• MOTOR SHAFT: stainless steel EN 10088-3 - 1.�10�.• MECHANICAL SEAL: ceramic - graphite - NBR.•ELECTRIC MOTOR: induction motor, for continu-
ous duty. Single-phase: 230 V - 50 Hz with capacitor and
thermal overload protector.• INSULATION: class F. •PROTECTION: IP 44.
STANDARD FEATURES:⇒ Carrying handle.⇒ Hosetails Ø 20 mm.⇒1.5 m power cable with Schuko plug.
CONSTRUCTION AND SAFETY STANDARDSEN �0 335-1 EN �003�-1IEC 335-1 IEC 3�-1CEI �1-150 CEI 2-3
75
DIMENSIONS AND WEIGHTS
Q
H(m
)
UTILITY/08M
UTILITY/07M
UTILITY/05M
f n
h
DN1 DN2
Ø2
Ø1h1
f1
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0Single-phase kW HP 0 5 10 15 20 25 30 35 �0 �5 50
UTILITY/05M 0.37 0.50H metres
35 32 27 24 21 19 17 16 15 14 13UTILITY/07M 0.50 0.70 41 36 31 27 24 22 20 19 17 16 15UTILITY/08M 0.60 0.85 47 42 38 34 31 28.5 26 24 22 21.5 19
TYPE PORTS DIMENSIONS mm kg
Single-phase DN1 DN2 Ø1 Ø2 f f1 h h1 n
UTILITY/05M
1” 1” 20 20439 379
260 255 230
10.0
UTILITY/07M 10.7
UTILITY/08M 447 387 10.9
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
n
h
7�7�
Q
H(m
)
UTILITY/08MSS
UTILITY/07MSS
UTILITY/05MSS
f n
h
DN1
DN2
Ø2
Ø1
h1
f1
DIMENSIONS AND WEIGHTS
TYPE POWER m3/hl/min
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0Single-phase kW HP 0 5 10 15 20 25 30 35 �0 �5 50
UTILITY/05MSS 0.37 0.50H metres
35 32 27 24 21 19 17 16 15 14 13UTILITY/07MSS 0.50 0.70 41 36 31 27 24 22 20 19 17 16 15UTILITY/08MSS 0.60 0.85 47 42 38 34 31 28.5 26 24 22 21.5 19
TYPE PORTS DIMENSIONS mm kg
Single-phase DN1 DN2 Ø1 Ø2 f f1 h h1 n
UTILITY/05MSS
1” 1” 20 20405 345
270 260 198
7.9
UTILITY/07MSS 8.0
UTILITY/08MSS 413 353 9.2
Q = Flow rate H = Total manometric head Tolerance of the performance curves according to EN ISO 9906 App. A.
77
COMPONENTS- Single-phase electropump 230V - 50Hz- PRESSURE CONTROL- 1.5 metre cable with Schuko plug
Domestic pumps with a pressure sensing electronic controller for auto-matic operation; the pump operates as required as a tap is opened or closed. The controller also provides protection for the pump against dry running.
Typical installation
*For correct operation of the PRESSURE CONTROL device, the height of the column of water must not exceed 15 metres
pumps with electronic controller
PC PUMP
DIMENSIONS
*max
imum
hei
ght a
ppro
x. 15
met
res
Peso 1.1 kg
TYPE POWERSingle-phase kW HP
PC/IP 500M 0.37 0.50PC/IP 700M 0.50 0.70PC/IP 800M 0.60 0.85PC/IP 1000M 0.75 1PC/IP 1500M 1.1 1.5PC/IC 100M 0.75 1PC/IC 100MH 0.75 1PC/IC 150M 1.1 1.5PC/IC 150LM 1.1 1.5PC/ICB 100NM 0.75 1PC/ICB 150HM 1.1 1.5PC/ICB 150MM 1.1 1.5PC/MSG 05M 0.37 0.50PC/MSG 07M 0.45 0.60PC/MSG 08M 0.60 0.85PC/MSG 08LM 0.60 0.85PC/MSG 10M 0.75 1PC/JS 05M 0.37 0.50PC/JS 07M 0.50 0.70PC/JS 08M 0.60 0.85PC/JS 10HM 0.75 1PC/JS 12HM 0.90 1.25PC/JS 15HM 1.1 1.5PC/JS 10LM 0.75 1PC/JS 12LM 0.90 1.25PC/JS 15LM 1.1 1.5PC/JSE 15HM 1.1 1.5PC/JSE 15MM 1.1 1.5PC/JSE 15LM 1.1 1.5
78
Small pressure sets with 2� litre spherical vessel, for automatic operation. Suitable for the supply of pressurised water in houses or in holiday homes.
(1) Maximum flow rate with the minimum recommended pressure switch settings(2) Pressure switch recommended rate
N.B. The pre-charge of air in diaphragm tanks must be set to a value 0.2 bar lower than the minimum setting of the pressure switch.
BOOSTER SETS-2� SP COMPONENTS- Single-phase pump 230 V - 50 Hz- 2� litre spherical vessel- Pressure switch “SQUARE-D” - Pressure gauge- 3 or 5-way brass connector- 1.5 metre cable with Schuko plug
BOOSTER SETS-24SP
TYPE PORTS POWERFLOW RATE
(1)
SETTING (recommended)
(2)
DIMENSIONSmm
Single-phase suc. deliv. kW HP l/min min max l a h2�SP/IP 500M 1” 1” 0.37 0.50 32 1.4 2.8 381 360 5132�SP/IP 700M 1” 1” 0.50 0.70 40 1.5 3.0 389 360 5182�SP/IP 800M 1” 1” 0.60 0.85 50 1.8 3.2 409 360 5312�SP/IP 1000M 1” 1” 0.75 1 50 2.2 3.6 409 360 5312�SP/IP 1500M 1” 1” 1.1 1.5 50 3.5 4.5 447 360 5492�SP/IC 75M 1” 1” 0.55 0.75 80 1.4 2.8 434 360 6172�SP/IC 100MH 1” 1” 0.75 1 90 1.8 3.2 434 360 6172�SP/IC 150M 11/4” 1” 1.1 1.5 120 2.2 3.5 470 360 6352�SP/IC 150LM 11/4” 1” 1.1 1.5 150 2.0 3.5 470 360 6352�SP/ICB 100NM 11/4” 1” 0.75 1 100 1.4 2.8 437 360 5762�SP/ICB 150HM 11/4” 1” 1.1 1.5 100 2.2 3.6 462 360 5992�SP/ICB 150MM 11/2” 1” 1.1 1.5 140 2.2 3.6 462 360 5992�SP/MSG 07M 1” 1” 0.45 0.60 60 1.4 2.8 401 360 5502�SP/MSG 08M 1” 1” 0.60 0.85 60 2.2 3.6 408 360 5502�SP/MSG 08LM 1” 1” 0.60 0.85 100 1.4 2.8 408 360 5502�SP/MSG 10M 1” 1” 0.75 1 100 2 3.5 423 360 5502�SP/MS 07M 1” 1” 0.45 0.60 60 1.4 2.8 435 360 5482�SP/MS 08M 1” 1” 0.60 0.85 60 2.2 3.6 443 360 5482�SP/MS 08LM 1” 1” 0.60 0.85 100 1.4 2.8 423 360 5482�SP/JS 05M 1” 1” 0.37 0.50 45 1.2 2.6 434 360 5362�SP/JS 07M 1” 1” 0.50 0.70 50 1.4 2.8 434 360 5362�SP/JS 08M 1” 1” 0.60 0.85 50 1.8 3.2 441 360 5362�SP/JS 10HM 1” 1” 0.75 1 50 2.0 3.2 460 360 5552�SP/JS 12HM 1” 1” 0.90 1.25 50 2.5 4.0 460 360 5552�SP/JS 15HM 1” 1” 1.1 1.5 50 3.0 4.5 460 360 5552�SP/JS 10LM 1” 1” 0.75 1 80 1.4 2.8 460 360 5552�SP/JS 12LM 1” 1” 0.90 1.25 80 2.0 3.5 460 360 5552�SP/JS 15LM 1” 1” 1.1 1.5 80 2.5 4.0 460 360 5552�SP/JSE 15HM 11/4” 1” 1.1 1.5 70 3.0 4.5 522 360 5832�SP/JSE 15MM 11/4” 1” 1.1 1.5 120 2.0 3.5 522 360 5832�SP/JSE 15LM 11/4” 1” 1.1 1.5 160 1.4 2.8 522 360 5832�SP/JET 05MSS 1” 1” 0.37 0.50 50 1.2 2.6 435 360 5482�SP/JET 07MSS 1” 1” 0.50 0.70 50 1.4 2.8 435 360 5482�SP/JET 08MSS 1” 1” 0.60 0.85 50 1.8 3.2 443 360 5482�SP/JET 10 HMSS 11/4” 1” 0.75 1 50 2.0 3.4 460 360 5792�SP/JET 12HMSS 11/4” 1” 0.90 1.25 50 2.4 3.8 460 360 5792�SP/JET 15HMSS 11/4” 1” 1.1 1.5 50 3.0 4.0 460 360 5792�SP/JET 10LMSS 11/4” 1” 0.75 1 80 1.4 2.8 460 360 5792�SP/JET 12LMSS 11/4” 1” 0.90 1.25 80 2.0 3.5 460 360 5792�SP/JET 15LMSS 11/4” 1” 1.1 1.5 80 2.5 4.0 460 360 579
PERFORMANCE AND DIMENSIONS PERFORMANCE AND DIMENSIONS
DN2
DN1
l a
h
79
DN2
DN1
l a
h
Small pressure sets with 20 litre cylindrical vessel, for automatic opera-tion. Suitable for the supply of pressurised water in houses or in holiday homes.
(1) Maximum flow rate with the minimum recommended pressure switch settings(2) Pressure switch recommended rate
N.B. The pre-charge of air in diaphragm tanks must be set to a value 0.2 bar lower than the minimum setting of the pressure switch.
BOOSTER SETS-2� CY COMPONENTS- Single-phase pump - 20 litre cylindrical vessel- Hose- Pressure switch “SQUARE-D” - Pressure gauge- 3 or 5-way brass connector- 1.5 metre cable with Schuko plug
BOOSTER SETS-24CY
TYPE PORTS POWERFLOW RATE
(1)
SETTING (recommended)
(2)
DIMENSIONSmm
Single-phase suc. deliv. kW HP l/min min max l a h2�CY/IP 500M 1” 1” 0.37 0.50 32 1.4 2.8 540 255 4752�CY/IP 700M 1” 1” 0.50 0.70 40 1.5 3.0 540 255 4802�CY/IP 800M 1” 1” 0.60 0.85 50 1.8 3.2 540 255 4902�CY/IP 1000M 1” 1” 0.75 1 50 2.2 3.6 540 255 4902�CTY/IP 1500M 1” 1” 1.1 1.5 50 3.5 4.5 540 255 5102�CY/IC 75M 1” 1” 0.55 0.75 80 1.4 2.8 540 255 5802�CY/IC 100MH 1” 1” 0.75 1 90 1.8 3.2 540 255 5802�CY/IC 150M 11/4” 1” 1.1 1.5 120 2.2 3.5 540 255 5952�CY/IC 150LM 11/4” 1” 1.1 1.5 150 2.0 3.5 540 255 5952�CY/ICB 100NM 11/4” 1” 0.75 1 100 1.4 2.8 540 255 5382�CY/ICB 150HM 11/4” 1” 1.1 1.5 100 2.2 3.6 540 255 5622�CY/ICB 150MM 11/2” 1” 1.1 1.5 140 2.2 3.6 540 255 5622�CY/MSG 07M 1” 1” 0.45 0.60 60 1.4 2.8 540 255 5102�CY/MSG 08M 1” 1” 0.60 0.85 60 2.2 3.6 540 255 5102�CY/MSG 08LM 1” 1” 0.60 0.85 100 1.4 2.8 540 255 5102�CY/MSG 10M 1” 1” 0.75 1 100 2 3.5 540 255 5102�CY/MS 07M 1” 1” 0.45 0.60 60 1.4 2.8 540 255 5092�CY/MS 08M 1” 1” 0.60 0.85 60 2.2 3.6 540 255 5092�CY/MS 08LM 1” 1” 0.60 0.85 100 1.4 2.8 540 255 5092�CY/JS 05M 1” 1” 0.37 0.50 45 1.2 2.6 540 265 4972�CY/JS 07M 1” 1” 0.50 0.70 50 1.4 2.8 540 265 4972�CY/JS 08M 1” 1” 0.60 0.85 50 1.8 3.2 540 265 4972�CY/JS 10HM 1” 1” 0.75 1 50 2.0 3.2 540 315 5152�CY/JS 12HM 1” 1” 0.90 1.25 50 2.5 4.0 540 315 5152�CY/JS 15HM 1” 1” 1.1 1.5 50 3.0 4.5 540 315 5152�CY/JS 10LM 1” 1” 0.75 1 80 1.4 2.8 540 315 5152�CY/JS 12LM 1” 1” 0.90 1.25 80 2.0 3.5 540 315 5152�CY/JS 15LM 1” 1” 1.1 1.5 80 2.5 4.0 540 315 5152�CY/JSE 15HM 11/4” 1” 1.1 1.5 70 3.0 4.5 540 290 5452�CY/JSE 15MM 11/4” 1” 1.1 1.5 120 2.0 3.5 540 290 5452�CY/JSE 15LM 11/4” 1” 1.1 1.5 160 1.4 2.8 540 290 5452�CY/JET 05MSS 1” 1” 0.37 0.50 50 1.2 2.6 540 255 5092�CY/JET 07MSS 1” 1” 0.50 0.70 50 1.4 2.8 540 255 5092�CY/JET 08MSS 1” 1” 0.60 0.85 50 1.8 3.2 540 255 5092�CY/JET 10 HMSS 11/4” 1” 0.75 1 50 2.0 3.4 540 255 5392�CY/JET 12HMSS 11/4” 1” 0.90 1.25 50 2.4 3.8 540 255 5392�CY/JET 15HMSS 11/4” 1” 1.1 1.5 50 3.0 4.0 540 255 5392�CY/JET 10LMSS 11/4” 1” 0.75 1 80 1.4 2.8 540 255 5392�CY/JET 12LMSS 11/4” 1” 0.90 1.25 80 2.0 3.5 540 255 5392�CY/JET 15LMSS 11/4” 1” 1.1 1.5 80 2.5 4.0 540 255 539
PERFORMANCE AND DIMENSIONS
80
DN2
DN1
l a
h
Pressure sets with �0 litre cylindrical vessel, for automatic operation. Suitable for the supply of pressurised water in houses.
BOOSTER SETS-�0 CY COMPONENTS- Single-phase pump - �0 litre cylindrical vessel- Hose- Pressure switch“SQUARE-D”- Pressure gauge- 3 or 5-way brass connector- 1.5 metre cable with Schuko plug
BOOSTER SETS-60CY
PERFORMANCE AND DIMENSIONS
TYPE PORTS POWERFLOW RATE
(1)
SETTING (recommended)
(2)
DIMENSIONSmm
Single-phase suc. deliv. kW HP l/min min max l a h
�0CY/IC 100MH 1” 1” 0.75 1 90 1.8 3.2 750 380 720
�0CY/IC 150M 11/4” 1” 1.1 1.5 120 2.2 3.5 750 380 735
�0CY/IC 150LM 11/4” 1” 1.1 1.5 150 2.0 3.5 750 380 735
�0CY/ICB 100NM 11/4” 1” 0.75 1 100 1.4 2.8 750 380 678
�0CY/ICB 150HM 11/4” 1” 1.1 1.5 100 2.2 3.6 750 380 702
�0CY/ICB 150MM 11/2” 1” 1.1 1.5 140 2.2 3.6 750 380 702
�0CY/MSG 10M 1” 1” 0.75 1 100 2 3.5 750 380 650
�0CY/JS 10HM 1” 1” 0.75 1 50 2.0 3.2 750 380 655
�0CY/JS 12HM 1” 1” 0.90 1.25 50 2.5 4.0 750 380 655
�0CY/JS 15HM 1” 1” 1.1 1.5 50 3.0 4.5 750 380 655
�0CY/JS 10LM 1” 1” 0.75 1 80 1.4 2.8 750 380 655
�0CY/JS 12LM 1” 1” 0.90 1.25 80 2.0 3.5 750 380 655
�0CY/JS 15LM 1” 1” 1.1 1.5 80 2.5 4.0 750 380 655
�0CY/JSE 15HM 11/4” 1” 1.1 1.5 70 3.0 4.5 750 380 685
�0CY/JSE 15MM 11/4” 1” 1.1 1.5 120 2.0 3.5 750 380 685
�0CY/JSE 15LM 11/4” 1” 1.1 1.5 160 1.4 2.8 750 380 685
�0CY/JET 10 HMSS 11/4” 1” 0.75 1 50 2.0 3.4 750 380 679
�0CY/JET 12HMSS 11/4” 1” 0.90 1.25 50 2.4 3.8 750 380 679
�0CY/JET 15HMSS 11/4” 1” 1.1 1.5 50 3.0 4.0 750 380 679
�0CY/JET 10LMSS 11/4” 1” 0.75 1 80 1.4 2.8 750 380 679
�0CY/JET 12LMSS 11/4” 1” 0.90 1.25 80 2.0 3.5 750 380 679
�0CY/JET 15LMSS 11/4” 1” 1.1 1.5 80 2.5 4.0 750 380 679
PERFORMANCE AND DIMENSIONS
(1) Maximum flow rate with the minimum recommended pressure switch settings(2) Pressure switch recommended rate
N.B. The pre-charge of air in diaphragm tanks must be set to a value 0.2 bar lower than the minimum setting of the pressure switch.
81
Pressure sets with 100 litre cylindrical vessel, for automatic operation. Suitable for the supply of pressurised water in houses.
BOOSTER SETS-100 CY COMPONENTS- Single-phase pump - 100 litre cylindrical vessel- Hose- Pressure switch “SQUARE-D”- Pressure gauge- 3 or 5-way brass connector- 1.5 metre cable with Schuko plug
DN2
DN1
l a
h
BOOSTER SETS-100CY
PERFORMANCE AND DIMENSIONS
TYPE PORTS POWERFLOW RATE
(1)
SETTING (recommended)
(2)
DIMENSIONSmm
Single-phase suc. deliv. kW HP l/min min max l a h
100CY/IC 150M 11/4” 1” 1.1 1.5 120 2.2 3.5 860 450 800
100CY/150 LM 11/4” 1” 1.1 1.5 150 2.0 3.5 860 450 800
100CY/ICB 100NM 11/4” 1” 0.75 1 100 1.4 2.8 860 450 743
100CY/ICB 150HM 11/4” 1” 1.1 1.5 100 2.2 3.6 860 450 767
100CY/ICB 150MM 11/2” 1” 1.1 1.5 140 2.2 3.6 860 450 767
100CY/MSG 10M 1” 1” 0.75 1 100 2 3.5 860 450 715
100CY/JS 10HM 1” 1” 0.75 1 50 2.0 3.2 860 450 720
100CY/JS 12HM 1” 1” 0.90 1.25 50 2.5 4.0 860 450 720
100CY/JS 15HM 1” 1” 1.1 1.5 50 3.0 4.5 860 450 720
100CY/JS 10LM 1” 1” 0.75 1 80 1.4 2.8 860 450 720
100CY/JS 12LM 1” 1” 0.90 1.25 80 2.0 3.5 860 450 720
100CY/JS 15LM 1” 1” 1.1 1.5 80 2.5 4.0 860 450 720
100CY/JSE 15HM 11/4” 1” 1.1 1.5 70 3.0 4.5 860 450 750
100CY/JSE 15MM 11/4” 1” 1.1 1.5 120 2.0 3.5 860 450 750
100CY/JSE 15LM 11/4” 1” 1.1 1.5 160 1.4 2.8 860 450 750
100CY/JET 10 HMSS 11/4” 1” 0.75 1 50 2.0 3.4 860 450 744
100CY/JET 12HMSS 11/4” 1” 0.90 1.25 50 2.4 3.8 860 450 744
100CY/JET 15HMSS 11/4” 1” 1.1 1.5 50 3.0 4.0 860 450 744
100CY/JET 10LMSS 11/4” 1” 0.75 1 80 1.4 2.8 860 450 744
100CY/JET 12LMSS 11/4” 1” 0.90 1.25 80 2.0 3.5 860 450 744
100CY/JET 15LMSS 11/4” 1” 1.1 1.5 80 2.5 4.0 860 450 744
(1) Maximum flow rate with the minimum recommended pressure switch settings(2) Pressure switch recommended rate
N.B. The pre-charge of air in diaphragm tanks must be set to a value 0.2 bar lower than the minimum setting of the pressure switch.
82
The features and specifications herein stated are in no way binding for the manufacturer. The manufacturer is free to modifiy the product at any time without previous notice.
NOTE
83
Ufficio
imm
agin
e & co
mun
icazio
ne co
d. C1
0502
2006