+ All Categories
Home > Documents > 06 07 TOYOTA AVALON GRILLE INSTALLATION MANUAL CARID.COM

06 07 TOYOTA AVALON GRILLE INSTALLATION MANUAL CARID.COM

Date post: 08-Apr-2018
Category:
Upload: enthonytopmak
View: 226 times
Download: 0 times
Share this document with a friend

of 3

Transcript
  • 8/7/2019 06 07 TOYOTA AVALON GRILLE INSTALLATION MANUAL CARID.COM

    1/3

    Upper Mesh Grille (includes):Mesh Section12 Gage Stainless Steel FrameTop Mounting Plate(3) Lower Mounting Brackets(4) Black Plastic Washers(14) #8-32 ESNA Half NutsHardware Kit (components listed below)#8 x 1/2 Black Truss Head Screws

    .040 x 1/2 Double Faced Tape

    1 x .189 x .064 Black Plastic Washers

    Stainless Steel Lock Washers

    #8-32 Stainless Steel Hex Nuts

    Emblem Mounting Plate

    1 Copyright 2006 by E&G Classics, Inc.

    1

    1822221

    Description Part No.Quantity

    ************1080-0020-061080-0038-061080-0157-061080-0041-061999-0256-001999-0065-001080-1902-063999-9035-003004-9248-921999-0264-001999-9555-001999-9072-001080-0158-06

    Copyright 2006 by E&G Classics, Inc.All right reserved. The reproduction or uti-lization of this work in any form or anyelectronic, mechanical, or other means, noknown or hereafter invented, including xe-rography, photocopying, and recording, andin any information storage retrieval systemis forbidden without written permission of

    owners.

    Notes to the Technician:E&G is proud to present this package to you and reminds you that fortechnical information, contact Lynn Eash or Lee Clary at 410-381-4900.Do not attempt installation any E&G product without first reading thedetailed instructions. E&G Classics will not warrantdamaged parts or

    vehicle due to altered installation instructions.

    IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE !

    2006-07 Toyota AvalonFine Mesh Grille

    J 19 G6

    Part #1080-0102-06

    1. Open the hood and push down on the centers of

    the plastic push fasteners to release them. Removeradiator cover (save for modifications).

    3. Unclip the lower edge of the factory grille and

    remove it from the bumper cover.

    1

    4

    PLEASE HANDLE WITH CARE! THE EDGES OF THE STAINLESSSTEEL MESH & GRILLE CAN BE EXTREMELY SHARP!

    2. Remove the 10mm hex head bolts (one each side)

    from the top of the factory grille. Remove the cen-ter push pin at the top of the grille (not shown).

    6

    5. Carefully remove the emblem from the OEM grille

    by unclipping it.6. Clean the back of the emblem and install the sup-plied double faced tape (where shown).

    3

    2

    WARNING:

    4. Use masking tape to tape around the factory grille

    opening 3/8 inside from the face of the bumpercover. Use flat or semi-gloss black paint and painteverything inside the taped factory grille openingthat will be visible through the mesh grille.

    Car Accessories | Toyota Accessories | Toyota Grilles

    http://www.carid.com/toyota-grill/http://www.carid.com/toyota-accessories/http://www.carid.com/
  • 8/7/2019 06 07 TOYOTA AVALON GRILLE INSTALLATION MANUAL CARID.COM

    2/3

    2 Copyright 2006 by E&G Classics, Inc.

    7. Peel off the double faced tape backing, align themounting tabs through the slots in the emblembacking plate and press the emblem firmly in placeto set the tape.

    9. Carefully center the emblem assembly onto themesh grille and install a 1 O.D. by 1/8 I.D. blackplastic washer, stainless steel lock washer and a#8-32 stainless steel nut onto each stud (asshown) and tighten.

    8. Trim the factory tabs protruding from the back ofthe emblem plate prior to installation onto the

    mesh grille to keep the tabs from contacting themesh.

    12. Once the lower mounting brackets are bent over,realign the modified radiator support cover, making

    sure that the cover fits underneath the top mount-ing plate. Reinstall all factory plastic push pins.

    8

    9

    8

    11

    10. Align the radiator support cover in place and markthe location of the hood latch assembly. Removethe cover and cut out the plastic in front of the

    assembly in order to reinstall it once the mesh grille isinstalled.

    11. Carefully align the mesh grille into place, then foldover the lower stainless steel mounting brackets tosecure the lower edge of the mesh grille.

    Car Accessories | Toyota Accessories | Toyota Grilles

    http://www.carid.com/toyota-grill/http://www.carid.com/toyota-accessories/http://www.carid.com/
  • 8/7/2019 06 07 TOYOTA AVALON GRILLE INSTALLATION MANUAL CARID.COM

    3/3

    http://www.carid.com/toyota-grill/http://www.carid.com/toyota-accessories/http://www.carid.com/

Recommended