MOUNTING INTERFACE OPERATING PRINCIPLE
MODULAR VERSIONNFPA D05 ISO 4401-05
P Q
maxmax
3000 PSI30 GPM
210 bar 114 I/min
PERFORMANCES HYDRAULIC SYMBOLS(measured with mineral oil of viscosity 36cSt at 120°F [50°C])
Maximum operating pressure PSI [bar]
GPM [l/min]
3000 [210]
30 [114]
400-1500 PSI [28-105 bar]1000-2500 PSI [70-175 bar]
5 drops per min
3:14.5:1
25 PSI [1.7 bar]
>85% of setting
No. of CCW turns from Min. to Max. settting
3.75
F˚ [C˚] -4 to 140 [-20 to +60]
F˚ [C˚] -4 to 176 [-20 to +80]
Max Flow rate
Pressure adjustment range: Code 150Code 300
Pilot ratio: Code 150Code 300
Check Valve cracking pressure
Adjustment Range:
Reseat
Ambient temperature range
Fluid temperature range
cST 100 - 400
cST 25Lbs [kg] 3.21 [1.46]
2.28 [1.03]
Fluid viscosity range
According to ISO 4406: 1999 Class 19/17/14Fluid contamination degree Recommended viscosity
Mass: P03MSV-CC P03MSV-CA, CB
Max valve leakage at reseat
P05MSV-CC/CA/CBPILOT OPERATED
COUNTERBALANCE VALVE
• The P05MSV-C counterbalance valves with pilot assist are designed to control an overrunning load or hold a load in position by maintaining a back pressure on the outlet of the cylinder. An integral check valve allows for free flow in the reverse direction. Valve conforms to NFPA D05/ISO 4401-05 standard for valve mounting interface.
• This valve can also be used as a brake valve in hydraulic motor circuits for a controlled deceleration.
• Counterbalance valves should be set at least 130% of maximum pressure due to load.
• Backpressure adds to the valve setting by (1.0 + pilot ratio) times the backpressure.
• Reverse flow will open the check at about 25 psi [1.7 bar].
• 3.75 turns of adjustment CCW from Min. to Max. pressure setting.
3.2
.126
[16.7].660
27
1.060
37.3
1.470
50.8
2.000
54.0
2.125
[6.3].250
[21.4].840
32.5
1.280
46
1.812
11.2.440 max
optional "T" port
1/4-20 [M6]
NFPA D05
DIMENSIONS: INCHES [mm]
ISO 4401-05-04-0-05
P
A B
T
A
A1 TB1P1 B1
TBBP
P05MSV-CC
TA1
TA
T
T
XG
A
A1 TB1P1 B1
TBBP
P05MSV-CC
TA1
TA
TB1
P
B1A1
BA
P1TA1
TA TB
TA1
TA
XG
P05MSV-CA
A
A1 TB1P1 B1
TBBP
P05MSV-CC
TA1
TA
TB1
P
B1A1
BA
P1TA1
TA TB
TB1TA1 P1A1
BA
B1
TBPTA
XX GG
P05MSV-CAP05MSV-CB
1
2
Countersunk hex adjustment screw: 5/32” [4 mm] allen wrench
Rotate counterclockwise to increase pressure
3 Qty. 5 O-rings - size AS568-014 (.489 ID x .070 CS) 90 Shore
4 1/4 NPTF Gauge Port
Locking nut: 9/16” wrench
1 • IDENTIFICATION CODE
Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals (code A). For fluids HFDR type (phosphate esters) use FPM seals (code G). For the use of other kinds of fluid such as HFA, HFB, HFC, please consult our technical department. Using fluids at temperatures higher than 176ºF [80ºC] causes a faster degradation of the fluid and of the seals characteristics.
The fluid must be preserved in its physical and chemical characteristics.
FORM NO. 1025245 REV 08-2019 © CONTINENTAL HYDRAULICS INC. ALL RIGHTS RESERVED.PRODUCT SPECIFICATIONS AND PERFORMANCE SUBJECT TO CHANGE WITHOUT NOTICE.
4895 12TH AVENUE EAST • SHAKOPEE, MN 55379
952.895.6400 • WWW.CONTINENTALHYDRAULICS.COM
2 • HYDRAULIC FLUIDS
3 • OVERALL AND MOUNTING DIMENSIONS
C A D P05MSV - - - -
D05 INTERFACE
VALVE SERIES
CODE NFPA SIZE
05
CONTROL PORT
CODE PORT
A A
B B
C A & B
MECHANICAL
CODE DESCRIPTION
OMIT STD W/ SOC HEAD ADJ.
MATERIAL SELECTION
CODE DESCRIPTION
A ALUMINUM
DESIGN LETTERVALVE TYPE
PRESSURE CONTROL
VALVE FUNCTION
CODE FUNCTION AVAIL WITH PORTS
C COUNTERBALANCE A, B, A & B
CODE
150
300
PSI
400-1500
1000-2500
BAR
28-105
70-175
PILOT RATIO
3:1
4.5:1
PRESSURE ADJUSTMENT RANGE
SEAL MATERIAL
CODE DESC.
A BUNA-N
G VITON
DIMENSIONS IN INCHES [mm]
50.01.97
20.1.79
1
2 3
40.41.59
134.95.31
175.26.90
215.48.48
8.6.34
63.52.50
36.31.43
108.74.28
50.01.97
149.05.87
21.4.84
11.1.44
4
108.74.28
21.4.84
50.01.97
149.05.87
43.61.72
4
43.6
1.718
P05MSV-CB
P05MSV-CA
P05MSV-CC
059-452P05MSV-CC_CA_CB_DIM.pdf
P05MSV-CA P05MSV-CB
TB1
P
B1A1
BA
P1
TB
TB1TA1 P1A1
BA
B1
TBPTA
X G
P05MSV-CB
TB1P1A1
BA
B1
TBP
X G