WALLBOX MODEL SETUP Move the SERVICE SWITCH on the CPA panel to SERVICE MODE. The display will show SCE and the current 2-digit record position number. While holding the CREDIT switch on, press digit 4 for GENERAL SETUP. Use the Left or Right RESET key and get to the rSE setting (Remote Selector type). From the list below, enter the 1 or 2 digit wallbox model code. Move the SERVICE SWITCH back to NORMAL PLAY MODE.
rSE WALLBOX MODEL Max Sel Seq Type
0 Seeburg digital DEC (requires the blue box DMT1, DEC-MCU TRANSLATOR) 160
1 Seeburg Consolette SC1/2/3/4, SCH1/2/3/4 160 Letter
2 Wurlitzer 5210, 5220, 5250 160 Number
3 Seeburg Wall-O-Matic 3W1, 3W100 100 Number
4 Seeburg Wall-O-Matic 3WA 160 Letter
5 Rowe WRA, WRB, WRC 160 Letter
6 AMI W-40, W-80, W-120, WQ200 160 Button
7 Wurlitzer 5207 104 Button
8 Wurlitzer 5225 100 Number
9 Wurlitzer 3020 24 Button
10 Rock-Ola 500, 1555, 1558 (and most other models) 160 Button
ORDER PART # SMC-WB5 for 50Hz version
COM (Y
EL
LO
W)
25VAC
SIG
(YE
LL
OW
)
WALLBOX SELECTOR
Black wire is not used. Apply tape or wire nut.
WALLBOX POWER
In-line fuse holder with 1A fuse
POWER TRANSFORMER 25-30 VAC, 2 Amps
Radio Shack 273-1512 or equivalent
NOT SUPPLIED But required to power wallbox
SMC-WB 3-Wire Wallbox
Adapter for GEN2 Seeburg SMC MCU
TECH NOTE Electrical pulses transmitted by the wallbox are generated by a contact arm rotating on a selector disc containing contact points. When these contacts become gummed up and corroded, the wallbox may not make the proper selection. Occasionally, these contacts require cleaning. They can be cleaned with a cloth saturated with isopropyl alcohol. Do not use emery cloth or sandpaper as this may remove the plating. On really worn wallboxes, where basic cleaning doesn’t seem to cure the problem, you may have successful results by using a low abrasive polish, such as “Scratch Out” or “Brasso”. This will make the contact surfaces shiny and smooth.
WALLBOX ADAPTER
SEEBURG SMC MCU GEN2
J2
ADAPTER INSTALLATION Insert the 9-pin connector to the J2 position on the GEN2 MCU board. The 2-wire zipcord receives the signal from the wallbox. You can extend the length of the wallbox signal wires, using 22AWG, to a distance of up to 2,000 feet (609.6 meters). The wallbox signal is 25VAC and has no specific wire polarity. You will need a 25-30 Volt, 2 Amp power transformer to power the wallbox Locate your wallbox model in the following pages for wiring detail.
WALLBOX SYSTEM WIRING
NBR LTR SEL REC
A1 A2 A3 A4 A5 A6 A7 A8 A9 A0
B1 B2 B3 B4 B5 B6 B7 B8 B9 B0
C1 C2 C3 C4 C5 C6 C7 C8 C9 C0
D1 D2 D3 D4 D5 D6 D7 D8 D9 D0
E1 E2 E3 E4 E5 E6 E7 E8 E9 E0
A1 B1 C1 D1 E1 F1 G1 H1 J1 K1
L1 M1 N1 P1 Q1 R1 S1 T1 U1 V1
A2 B2 C2 D2 E2 F2 G2 H2 J2 K2
L2 M2 N2 P2 Q2 R2 S2 T2 U2 V2
A3 B3 C3 D3 E3 F3 G3 H3 J3 K3
1 2 3 4 5 6 7 8 9
10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
100 200 101 201 102 202 103 203 104 204
105 205 106 206 107 207 108 208 109 209
110 210 111 211 112 212 113 213 114 214
115 215 116 216 117 217 118 218 119 219
120 220 121 221 122 222 123 223 124 224
NBR LTR SEL REC
F1 F2 F3 F4 F5 F6 F7 F8 F9 F0
G1 G2 G3 G4 G5 G6 G7 G8 G9 G0
H1 H2 H3 H4 H5 H6 H7 H8 H9 H0
J1 J2 J3 J4 J5 J6 J7 J8 J9 J0
K1 K2 K3 K4 K5 K6 K7 K8 K9 K0
L3 M3 N3 P3 Q3 R3 S3 T3 U3 V3
A4 B4 C4 D4 E4 F4 G4 H4 J4 K4
L4 M4 N4 P4 Q4 R4 S4 T4 U4 V4
A5 B5 C5 D5 E5 F5 G5 H5 J5 K5
L5 M5 N5 P5 Q5 R5 S5 T5 U5 V5
51 52 53 54 55 56 57 58 59 60
61 62 63 64 65 66 67 68 69 70
71 72 73 74 75 76 77 78 79 80
81 82 83 84 85 86 87 88 89 90
91 92 93 94 95 96 97 98 99
100
125 225 126 226 127 227 128 228 129 229
130 230 131 231 132 232 133 233 134 234
135 235 136 236 137 237 138 238 139 239
140 240 141 241 142 242 143 243 144 244
145 245 146 246 147 247 148 248 149 249
NBR LTR SEL REC
L1 L2 L3 L4 L5 L6 L7 L8 L9 L0
M1 M2 M3 M4 M5 M6 M7 M8 M9 M0
N1 N2 N3 N4 N5 N6 N7 N8 N9 N0
P1 P2 P3 P4 P5 P6 P7 P8 P9 P0
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q0
A6 B6 C6 D6 E6 F6 G6 H6 J6 K6
L6 M6 N6 P6 Q6 R6 S6 T6 U6 V6
A7 B7 C7 D7 E7 F7 G7 H7 J7 K7
L7 M7 N7 P7 Q7 R7 S7 T7 U7 V7
A8 B8 C8 D8 E8 F8 G8 H8 J8 K8
101 102 103 104 105 106 107 108 109 110
111 112 113 114 115 116 117 118 119 120
121 122 123 124 125 126 127 128 129 130
131 132 133 134 135 136 137 138 139 140
141 142 143 144 145 146 147 148 149 150
150 250 151 251 152 252 153 253 154 254
155 255 156 256 157 257 158 258 159 259
160 260 161 261 162 262 163 263 164 264
165 265 166 266 167 267 168 268 169 269
170 270 171 271 172 272 173 273 174 274
NBR LTR SEL REC
R1 R2 R3 R4 R5 R6 R7 R8 R9 R0
L8 M8 N8 P8 Q8 R8 S8 T8 U8 V8
151 152 153 154 155 156 157 158 159 160
175 275 176 276 177 277 178 278 179 279
SEQUENCED NUMBER
SEQUENCED LETTER
SELECTION BUTTON
RECORD SELECTED
WALLBOX TRANSLATION CHART
Seeburg Wall-o-matic 3W1 / 3W100
100 select
Seeburg Wall-o-matic 3WA
200 select
COMMON 25VAC SIGNAL
SIGNAL
25VAC
COMMON
Wallbox Wiring Diagrams CAUTION: Do not attempt to hook up a wallbox power supply if you are not familiar with electrical wiring, consult with a qualified person or an electrician. Do not leave any wires exposed, always use wire-nuts or electrical tape on all connections. Improper wiring can result in a fire or shock hazard.
Seeburg Consolette SC1-4 / SCH1-4
160 select
Wurlitzer 5220 200 select
Wurlitzer 5225
100 select
BLK WHT BLU
COMMON 25VAC SIGNAL
25VAC COMMON SIGNAL
3 G 1
To enable coin operation, the BRN / RED / ORG terminals must be shorted together and connected to the 25VAC terminal (WHT) using a 40-50 Ohm, 10 Watt power resistor (solenoid current = 400mA).
Wurlitzer 5207 104 select
SIGNAL COMMON 25VAC
AMI W-40 / W-80 / W-120 40 / 80 / 120 select
COMMON
Rowe WRA / WRB / WRC 200 select
1 2 3 4
COMMON 25VAC SIGNAL 25VAC*
A wire jumper must be inserted from the 25VAC main power terminal (#2) to the 25VAC* keypad motor terminal (#4).
25VAC
SIGNAL
Wurlitzer 5210 200 select
SIGNAL COMMON 25VAC
Rock-Ola 1555 200 select
Rock-Ola 1558 160 select
COMMON SIGNAL 25VAC COMMON SIGNAL 25VAC
25VAC
COMMON
SIGNAL
Wurlitzer 5250 200 select
Rock-Ola 500 160 select
25VAC COMMON SIGNAL
Wurlitzer 3020 24 select
SIGNAL 25VAC 120VAC
This wallbox has its own “built-in” transformer and requires a 120VAC power cord. High voltage is used so be very careful when wiring up this wallbox. The wallbox adapter only requires the two wire connection to terminal #1 and terminal #3.
The Original 1015 Bubbler Wallbox
AMI WQ-200 200 select
COMMON 25VAC SIGNAL 25VAC*
A wire jumper must be inserted from the 25VAC main power terminal to the 25VAC* lock-out.
![DIY Seeburg Wallbox Decoder · 2020. 7. 17. · Seeburg Wall-0-Matic [Retro Future Electrics] Raspberry Pi Project -A 1960s wallbox interfaced with Sanos [Phil Lavin] One common theme](https://static.documents.pub/doc/80x56/6149fe6d12c9616cbc692026/diy-seeburg-wallbox-2020-7-17-seeburg-wall-0-matic-retro-future-electrics.jpg)
