48
4/10 HP Submersible Sewage Pump, 2" SolidsSW-40 Series
Features
Handles liquids and solid waste materials up to 2" diameter.
Cast iron pump housing and cover with protective epoxy coating for corrosion resistance.
Oil-filled motor housing for lifetime lubrication and rapid heat dissipation.
Stainless steel fasteners.
Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces).
Thermal overload protection.
Manual and automatic models.
Automatic operation has a 9 to 14 inch “ON” level and 2 to 6 inch “OFF” level range with piggyback mechanical float switch.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
Sewage
115 Volt Models Only
GLASS-FILLED NYLONVORTEX IMPELLER
MOTOR DESIGNED FOR MAXIMUM PERFORMANCE
STAINLESS STEEL SCREWS
CARBON AND CERAMICFACE SEAL
LOWER BALLBEARING
UPPER SINTERED SLEEVEBEARING FOR SMOOTH
OPERATION ANDEXTENDED LIFE
CAST IRON COVER,HOUSING AND VOLUTE
WITH PROTECTIVEEPOXY COATING TORESIST CORROSION
OIL-FILLED TODISSIPATE HEATFOR MAXIMUM LIFE
49
SW-40 Series 4/10 HP Submersible Sewage Pump, 2" Solids
Sewage
10.3"
5.3"
2" FNPTDISCHARGE
2" DIA. INTAKE2"
11.5" 6.8"
5.4"
AF - Piggyback Mechanical Float Switch* without plug
Specifications
Cover Epoxy Coated Cast Iron
Motor Housing Epoxy Coated Cast Iron
Impeller Material Nylon
Impeller Type Vortex
Volute Epoxy Coated Cast Iron
Power Cord SJTW
Mechanical Shaft SealNitrile with Carbon and Ceramic Faces
Fasteners Stainless Steel
Shaft Steel
BearingsUpper - Sintered SleeveLower - Ball Bearing
Construction
0
5
15
10
20
0 10 20 30 40 7050 60 80
FLOW - GALLONS/MINUTE
0.0
4.0
2.0
1.0
5.0
6.0
3.0
0 50 100 150 200 250 300
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO. ITEM NO. HP VOLTS DISCHARGE SIZE RUNNING AMPS/WATTS
PERFORMANCE (GPM) SHUT-OFF CORD LENGTH
WEIGHT(LBS)5' 10' 15' FEET PSI
SW-40509403 4/10 115 2" FNPT 13/1020 80.0 50.0 16.0 18.0 7.8 15' 36.0509451 4/10 230 2" FNPT 6.5/1020 80.0 50.0 16.0 18.0 7.8 15'* 36.0
SW-40-AF 509501 4/10 115 2" FNPT 13/1020 80.0 50.0 16.0 18.0 7.8 15' 36.0
50
4/10 HP Submersible Sewage Pump, 2" SolidsSWL-40 Series
Features
Powerful, 4/10 HP Permanent Split Capacitor (PSC) motor for high starting and running torque, with low Amp draw to conserve electrical energy.
Recessed, vortex impeller made of tough, engineered composite material to reduce clogging; will pass 2-inch spherical solids.
Upper and lower ball bearings for extended motor life.
Mechanical seal (stainless steel spring, nitrile parts, carbon and ceramic faces) to assure maximum protection against pump failure.
Rugged cast iron pump housing with epoxy coating for corrosion resistance.
Diaphragm pressure switch for automatic operation.
Oil-filled motor housing for lifetime bearing lubrication and maximum heat dissipation.
Stainless steel hardware to protect against corrosion.
Thermal overload protection.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
Sewage
SWL-40-AD
SWL-40
C US
SWITCHBREATHER
TUBE
OPERATIONAUTOMATIC
PIGGYBACK PLUG
7.6
10.7
10.5
10.7
7.6
14.814.8
SWITCHOFF 5"
SWITCHON 15"
APPROX
APPROX
2" FNPT2" FNPT
51
SWL-40 Series 4/10 HP Submersible Sewage Pump, 2" Solids
Sewage
Motor Housing Epoxy Coated Cast Iron
Impeller Material Engineered Composite
Impeller Type Recessed, Vortex
Volute Epoxy Coated Cast Iron
Power Cord 16/3 SJTW-A
Mechanical Shaft Seal Nitrile with Carbon and Ceramic Faces
Fasteners Stainless Steel
Shaft Cold Rolled Steel
Bearings Ball Bearings
Construction
Specifications
0
5
15
10
20
0 10 20 30 40 70 9050 60 10080
FLOW - GALLONS/MINUTE
0.0
4.0
2.0
1.0
5.0
6.0
3.0
0 100 200 300
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO. ITEM NO. HP VOLTS DISCHARGE SIZE RUNNING AMPS/WATTS
PERFORMANCE (GPM) SHUT-OFF CORD LENGTH
WEIGHT(LBS)5' 10' 15' FEET PSI
SWL-40 509462 4/10 115 2" FNPT 8.9/870 95.0 60.0 22.0 18.0 7.8 20' 52.0
SWL-40-AD509563 4/10 115 2" FNPT 8.9/870 95.0 60.0 22.0 18.0 7.8 20' 53.0509564 4/10 230 2" FNPT 4.5/870 95.0 60.0 22.0 18.0 7.8 20' 55.0
60
1/2 HP Manual Submersible Sewage Pump, 2" SolidsSW-50 Series
Features
Handles liquids and solid waste materials up to 2-inch diameter.
Cast iron pump housing and volute with protective epoxy coating for corrosion and rust resistance.
Oil-filled motor housing for lifetime lubrication and rapid heat dissipation.
Stainless steel fasteners.
Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces).
Thermal overload protection.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
Sewage
HEAVY DUTY POWER CORD
UPPER BALLBEARING
EPOXY-COATEDCAST IRON COVER
ENGINEERED,HIGH-IMPACT
THERMOPLASTICBASE ALLOWS
¾" SOLIDS
OIL-FILLED TODISSIPATE HEAT
FOR MAXIMUM LIFE
GLASS-FILLEDNYLON VORTEX IMPELLER
LOWER BALLBEARING
CAST IRON HOUSINGWITH PROTECTIVE EPOXY COATING TO RESIST CORROSION
MOTOR DESIGNEDFOR MAXIMUM
PERFORMANCECARBON & CERAMICFACE SEAL
61
MODEL NO. ITEM NO. HP VOLTS DISCHARGE SIZE RUNNING AMPS/WATTS
PERFORMANCE (GPM) SHUT-OFF CORD LENGTH
WEIGHT(LBS)5' 10' 15' FEET PSI
SW-50511402 ½ 115 2" FNPT 12/1000 110.0 85.0 45.0 20.0 8.7 15' 44.0511476 ½ 208/230 2" FNPT 6.6/1100 110.0 85.0 45.0 20.0 8.7 15' 44.0
SW-50 Series 1/2 HP Manual Submersible Sewage Pump, 2" Solids
Sewage
12.70
2.00" DIA.INTAKE
2" OR 3"NPTDISCHARGE
11.40
8.25
5.50
Motor Housing Epoxy Coated Cast Iron
Impeller Material Nylon
Impeller Type Vortex
Volute Epoxy Coated Cast Iron
Power Cord SJTW
Mechanical Shaft Seal Nitrile with Carbon and Ceramic Faces
Fasteners Stainless Steel
Shaft Steel
Bearings Ball Bearings
Construction
Specifications
0
5
15
10
20
0 20 40 60 80 100 120
FLOW - GALLONS/MINUTE
0.0
4.0
2.0
1.0
5.0
6.0
7.0
3.0
0 100 200 300 400
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
62
1/2 HP Automatic Submersible Sewage Pump, 2" SolidsSW-50-A Series
Features
Handles liquids and solid waste materials up to 2" diameter.
Cast iron pump housing with protective epoxy coating for corrosion resistance.
Oil-filled motor housing for lifetime lubrication and rapid heat dissipation.
Stainless steel screws, bolts, handle and switch guard.
Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces).
Thermal overload protection.
Integral snap-action float switch - Automatic operation has 11 to 14 inch “ON” level range and 5 to 8 inch “OFF” level range.
Piggyback mechanical float switch - Automatic operation has 15 to 17 inch “ON” level range and 8 to 10 inch “OFF” level range.
PSC type motor with upper and lower ball bearings.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
HEAVY DUTY POWER CORD
MOTOR DESIGNEDFOR MAXIMUM PERFORMANCE
OIL-FILLED TO DISSIPATEHEAT FOR EXTENDED LIFE
CAST IRON HOUSING WITHPROTECTIVE EPOXY COATINGTO RESIST CORROSION
EPOXY COATED CAST IRON VOLUTE
STAINLESS STEEL LIFTING RING HANDLE
UPPER ANDLOWER BALL
BEARINGS
GLASS-FILLED NYLONVORTEX IMPELLER
STAINLESS STEEL SCREWS
Sewage
63
SW-50-A Series 1/2 HP Automatic Submersible Sewage Pump, 2" Solids
Sewage
2.00
2.00" DIA. INTAKE
5.30
12.70
5.50
10.30
8.25
2" FNPTDISCHARGE
15 FT POWER CORD
Motor Housing Epoxy Coated Cast Iron
Impeller Material Glass-Filled Nylon
Impeller Type Vortex
Volute Epoxy Coated Cast Iron
Power Cord 16-3 SJTW
Mechanical Shaft Seal Nitrile with Carbon and Ceramic Faces
Fasteners Stainless Steel
Shaft Steel
Bearings Ball Bearings
Construction
Specifications
0
5
15
10
20
25
0 20 40 60 80 100 120
FLOW - GALLONS/MINUTE
0.0
4.0
2.0
1.0
5.0
6.0
7.0
3.0
0 100 200 300 400
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO. ITEM NO. HP VOLTS DISCHARGE SIZE RUNNING AMPS/WATTS
PERFORMANCE (GPM) SHUT-OFF CORD LENGTH
WEIGHT(LBS)5' 10' 15' FEET PSI
SW-50-AF 511502 ½ 115 2" FNPT 12/1000 110.0 85.0 45.0 20.0 8.7 15' 45.0
SW-50-AS511551 ½ 115 2" FNPT 9.2/1086 110.0 85.0 45.0 20.0 8.7 10' 46.0511566 ½ 230 2" FNPT 4.6/1086 110.0 85.0 45.0 20.0 8.7 25' 47.0
64
1/2 HP Automatic Submersible Sewage Pump, 2" SolidsSWL-50-AD Series
Features
Powerful, ½ HP Permanent Split Capacitor (PSC) motor for high starting and running torque, with low amp draw to conserve electrical energy.
Recessed, vortex impeller made of tough, engineered composite material to reduce clogging. Will pass 2" spherical solids.
Upper and lower ball bearings for extended motor life.
Mechanical seal (stainless steel spring, nitrile parts, carbon and ceramic faces) to assure maximum protection against pump failure.
Rugged cast iron pump housing with epoxy coating for corrosion resistance.
Diaphragm pressure switch for automatic operation.
Oil-filled motor housing for lifetime bearing lubrication and maximum heat dissipation.
Stainless steel hardware to protect against corrosion.
Thermal overload protection.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
SWITCHBREATHER
TUBE
OPERATIONAUTOMATIC
PIGGYBACK PLUG
Sewage
C US
65
SWL-50-AD Series 1/2 HP Automatic Submersible Sewage Pump, 2" Solids
Sewage
SWL-50-AD SWL-50
Motor Housing Epoxy Coated Cast Iron
Impeller Material Engineered Composite
Impeller Type Recessed, vortex
Volute Epoxy Coated Cast Iron
Power Cord 16/3 SJTW-A
Mechanical Shaft Seal Nitrile with Carbon and Ceramic Faces
Fasteners Stainless Steel
Shaft Cold Rolled Steel
Bearings Ball Bearings
Construction
Specifications
10.5
10.7
7.6
2" FNPT
7.6
10.7
2" FNPT
14.8
SWITCHOFF 5"
SWITCHON 15"
APPROX
APPROX
14.8
0
5
15
10
20
25
0 20 40 60 80 100 120
FLOW - GALLONS/MINUTE
0.0
4.0
2.0
1.0
5.0
6.0
7.0
3.0
0 100 200 300 400
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO. ITEM NO. HP VOLTS DISCHARGE SIZE RUNNING AMPS/WATTS
PERFORMANCE (GPM) SHUT-OFF CORD LENGTH
WEIGHT(LBS)5' 10' 15' FEET PSI
SWL-50 511502 ½ 115 2" FNPT 12/1000 120.0 85.0 48.0 12.0 22.0 10' 53.0
SWL-50-AD511551 ½ 115 2" FNPT 9.2/1086 120.0 85.0 48.0 12.0 22.0 10' 54.0511566 ½ 230 2" FNPT 4.6/1086 120.0 85.0 48.0 12.0 22.0 20' 54.0
66
1/2 HP Manual Submersible Sewage Pump, 2" SolidsSW-50H Series
HEAVY DUTY POWER CORD
MOTOR DESIGNED FORMAXIMUM PERFORMANCE
DYNAMICALLYBALANCEDCAST IRONIMPELLER
STAINLESS STEEL LIFTING RING
CARBON & CERAMICFACE SEAL
EXCLUSION SEAL TOPROTECT MECHANICALSEAL
CAPACITOR ANDPOWER CORDCONNECTIONS
BALL BEARINGSUPPER AND LOWER
ALL CAST IRONCONSTRUCTION
WITH PROTECTIVEBAKED-ON EPOXY
COATING TO RESISTCORROSION
OIL-FILLED TODISSIPATE HEATFOR MAXIMUM LIFE
Features
Handles liquids and solid waste materials up to 2-inch diameter.
Cast iron pump housing with protective epoxy coating for corrosion resistance.
Oil-filled motor housing for lifetime lubrication and rapid heat dissipation.
Stainless steel screws, bolts and lifting ring.
Mechanical seal (stainless steel spring, nitrile parts, carbon and ceramic faces) for long life and reliability.
Secondary exclusion seal to help protect mechanical seal.
½ hp, 1625 RPM, ball bearing motor and thermal overload protection.
Capacitor and power cord connections isolated from oil -filled motor housing for ease of field maintenance.
Dynamically balanced two-vane non-clogging impeller with pump-out vanes to enhance pumping performance and efficiency.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
Sewage
115 V Models Only
67
SW-50H Series 1/2 HP Manual Submersible Sewage Pump, 2" Solids
Sewage
14.07
9.89
6.92
2.00
5.71
16.15
Motor Housing Epoxy Coated Cast Iron
Impeller Material Epoxy Coated Cast Iron
Impeller Type Two Vane, Non-Clog
Volute Epoxy Coated Cast Iron
Power Cord 16/3, STW
Mechanical Shaft Seal Nitrile with Carbon and Ceramic Faces
Fasteners Stainless Steel
Shaft Stainless Steel
Bearings Ball Bearings
Construction
Specifications
0
5
15
10
20
25
0 20 40 60 80 100 120
FLOW - GALLONS/MINUTE
0.0
4.0
2.0
1.0
5.0
6.0
7.0
8.0
3.0
0 100 200 300 400
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO. ITEM NO. HP VOLTS DISCHARGE SIZE RUNNINGAMPS/WATTS
PERFORMANCE (GPM) SHUT-OFF CORD
LENGTHWEIGHT
(LBS)10' 20' FEET PSI
SW-50H514322 ½ 115 2" 11.6/1100 100.0 35.0 25.0 10.8 20' 87.0514323 ½ 208-240 2" 4.6/1100 100.0 35.0 25.0 10.8 20' 88.0
68
1 HP Manual Submersible Sewage Pump, 2" SolidsSW-100 Series
STAINLESS STEEL LIFTING RINGHEAVY DUTY POWER CORD
ALL CAST IRONCONSTRUCTION
WITH PROTECTIVEBAKED-ON EPOXY
COATING TO RESISTCORROSION
OIL-FILLED TODISSIPATE HEATFOR EXTENDEDPUMP LIFE
CAPACITOR ANDPOWER CORDCONNECTIONS
BALL BEARINGSUPPER AND LOWER
CARBON & CERAMIC FACE SEAL
EXCLUSION SEALTO PROTECTMECHANICAL SEAL
DYNAMICALLYBALANCED CAST
IRON IMPELLER
MOTOR DESIGNEDFOR MAXIMUMPERFORMANCE
Features
Handles liquids and solid waste materials up to 2" diameter.
Cast iron pump housing with protective epoxy coating for corrosion resistance.
Oil-filled motor housing for lifetime lubrication and rapid heat dissipation.
Stainless steel screws, bolts and lifting ring.
Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces) for long life and reliability.
Secondary exclusion seal to help protect mechanical seal.
1 hp ball bearing motor.
Thermal overload protection.
Permanent split capacitor design on single-phase models.
Capacitor and power cord isolated from oil-filled motor housing for ease of field maintenance.
Dynamically balanced two-vane non-clogging impeller with pump-out vanes to protect seal
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
Sewage
575 volt model is CSA only
69
SW-100 Series 1 HP Manual Submersible Sewage Pump, 2" Solids
*3-phase pumps require control panel to operate**Without plug
Sewage
14.07
9.89
6.92
2.00
5.71
16.15
Motor Housing Epoxy Coated Cast Iron
Impeller Material Epoxy Coated Cast Iron
Impeller Type Two Vane, Non-Clog
Volute Epoxy Coated Cast Iron
Power Cord 16/3, STW
Mechanical Shaft Seal Nitrile with Carbon and Ceramic Faces
Fasteners Stainless Steel
Shaft Stainless Steel
Bearings Ball Bearings
Construction
Specifications
0
5
15
30
10
20
35
25
40
0 20 40 60 80 100 120 140 160 180 200
FLOW - GALLONS/MINUTE
0.0
8.0
4.0
2.0
10.0
12.0
6.0
0 100 200 300 400 500 600 700
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
380V 50 Hz
60 Hz
MODELNO.
ITEMNO. HP VOLTS PHASE DISCHARGE
SIZERUNNING
AMPS/WATTSPERFORMANCE (GPM) SHUT-OFF CORD
LENGTH**WEIGHT
(LBS)5' 10' 20' 30' FEET PSI
SW-100
514621 1 230 1 3" 11.0/1900 180 160 100 32 35.0 15.1 20' 88.0514626 1 200-208 1 3" 11.0/2000 180 160 100 32 35.0 15.1 20' 88.0514721 1 230 3* 3" 6.3/1550 180 160 100 32 35.0 15.1 20' 88.0514731 1 460/380 3* 3" 3.2/1400 180 160 100 32 35.0 15.1 20' 88.0514741 1 575 3* 3" 2.5/1400 180 160 100 32 35.0 15.1 20' 88.0514751 1 200-208 3* 3" 6.8/1400 180 160 100 32 35.0 15.1 20' 88.0
70
1.5 HP Manual Submersible Sewage Pump, 2" SolidsSW-150 Series
HEAVY DUTYPOWER CORD
DYNAMICALLYBALANCED
BRASS IMPELLER
UPPER AND LOWERBALL BEARINGS
CARBON ANDCERAMIC FACE SEAL
STATOR PRESSED INTOHOUSING, ENGINEERED FOR EFFICIENT HEAT DISSIPATION
STAINLESS STEEL LIFTING RING
CAPACITOR ANDPOWER CORD
CONNECTIONS
ALL CAST IRON CONSTRUCTION WITH PROTECTIVE BAKED-ON EPOXY COATING TO RESIST CORROSION
OIL-FILLED TO DISSIPATE HEATFOR EXTENDED PUMP LIFE
EXCLUSION SEALTO PROTECTMECHANICAL SEAL
Features
Handles liquids and solid waste materials up to 2" diameter.
Cast iron pump housing with protective epoxy coating for corrosion resistance.
Oil-filled motor housing for lifetime lubrication and rapid heat dissipation.
Stainless steel hardware.
Mechanical seal (stainless steel spring, nitrile parts, carbon and ceramic faces) for long life and reliability.
1.5 hp ball bearing motor.
Exclusion seal.
Thermal overload protection on single phase units.
Capacitor and power cord isolated from oil-filled motor housing for ease of field maintenance.
Brass impeller.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
Sewage
71
SW-150 Series 1.5 HP Manual Submersible Sewage Pump, 2" Solids
*3-phase pumps require control panel
Sewage
Cover Epoxy Coated Cast Iron
Motor Housing Epoxy Coated Cast Iron
Impeller Material Red Brass
Impeller Type Non-Clog
Volute Epoxy Coated Cast Iron
Power Cord 14/3, SOW (1-Phase), 14/4, SOW (3-Phase)
Mechanical Shaft Seal Carbon/Ceramic
Fasteners Stainless Steel
Shaft Stainless Steel
Bearings Ball Bearings
Construction
2.0"
7.6"
18.4"
4.2"
12.9"
8.4"
6.5"
Specifications
0
10
30
60
20
40
70
50
0 20 40 60 80 100 120 140 160 180
FLOW - GALLONS/MINUTE
0.0
20.0
10.0
5.0
15.0
0 100 200 300 400 500 600
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO.
ITEMNO. HP VOLTS PHASE DISCHARGE
SIZERUNNING
AMPS/WATTSPERFORMANCE (GPH) SHUT-OFF CORD
LENGTHWEIGHT
(LBS)10' 20' 30' 40' 50' 60' FEET PSI
SW-150
520305 1.5 208 1 3" 16.0/3229 160.0 137.0 111.0 84.0 50.0 15.0 64.0 27.7 20' 96.0520306 1.5 230 1 3" 15.5/3512 160.0 137.0 111.0 84.0 50.0 15.0 64.0 27.7 20' 96.0520307 1.5 200-208 3* 3" 13.5/1644 160.0 137.0 111.0 84.0 50.0 15.0 64.0 27.7 20' 96.0520308 1.5 230 3* 3" 11.5/1512 160.0 137.0 111.0 84.0 50.0 15.0 64.0 27.7 20' 96.0520309 1.5 460 3* 3" 5.3/1474 160.0 137.0 111.0 84.0 50.0 15.0 64.0 27.7 20' 96.0
72
2 HP Manual Submersible Sewage Pump, 2" SolidsSW-200 Series
Features
Handles liquids and solid waste materials up to 2-inch diameter.
Cast iron pump housing with protective epoxy coating for corrosion resistance.
Oil-filled motor housing for lifetime lubrication and rapid heat dissipation.
Stainless steel screws, bolts and seal assembly.
Mechanical seal (stainless steel spring, nitrile parts, carbon and ceramic faces) for long life and reliability.
2 hp ball bearing motor.
Exclusion seal.
Thermal overload protection on single phase units.
Capacitor and power cord isolated from oil-filled motor housing for ease of field maintenance.
Brass impeller.
Franklin Electric wastewater pumps are rated continuous duty as long as they are run within the published ratings for these pumps.
Sewage
HEAVY DUTYPOWER CORD
CARBONAND CERAMIC
FACE SEAL
BALL BEARINGSUPPER AND LOWER
CAPACITOR ANDPOWER CORD
CONNECTIONS
DYNAMICALLYBALANCED
BRASS IMPELLER
STAINLESS STEEL LIFTING RING
ALL CAST IRONCONSTRUCTION WITHPROTECTIVE BAKED-ONEPOXY COATING TORESIST CORROSION
STATOR PRESSED INTO HOUSINGENGINEERED FOR EFFICIENT HEAT DISSIPATION
EXCLUSION SEALTO PROTECTMECHANICAL SEAL
OIL-FILLED TO DISSIPATE HEAT FOR EXTENDED PUMP LIFE
73
SW-200 Series 2 HP Manual Submersible Sewage Pump, 2" Solids
Sewage
1.77
6.27
17.08
4.21
12.92
8.42
6.50
Cover Epoxy Coated Cast Iron
Motor Housing Epoxy Coated Cast Iron
Impeller Material Red Brass
Impeller Type Non-Clog
Volute Epoxy Coated Cast Iron
Power Cord 14/3, SOW
Mechanical Shaft Seal Carbon/Ceramic
Fasteners Stainless Steel
Shaft Stainless Steel
Bearings Ball Bearings
Construction
*3-phase pumps require control panel
Specifications
0
10
30
60
80
20
40
70
50
0 25 50 75 100 125 150 175 200 225
FLOW - GALLONS/MINUTE
0.0
20.0
10.0
5.0
15.0
0 200 400 600 800
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO.
ITEMNO. HP VOLTS PHASE DISCHARGE
SIZERUNNING
AMPS/WATTSPERFORMANCE (GPH) SHUT-OFF CORD
LENGTHWEIGHT
(LBS)10' 20' 30' 40' 50' 60' FEET PSI
SW-200
520101 2 208/230 1 3" 18.0/4118 205.0 168.0 140.0 115.0 90.0 70.0 77.0 33.3 20' 96.0520126 2 200-208 3* 3" 14.5/2769 205.0 168.0 140.0 115.0 90.0 70.0 77.0 33.3 20' 96.0520151 2 230 3* 3" 12.6/2686 205.0 168.0 140.0 115.0 90.0 70.0 77.0 33.3 20' 96.0520176 2 460 3* 3" 6.1/2771 205.0 168.0 140.0 115.0 90.0 70.0 77.0 33.3 20' 96.0
74
2 HP Manual Submersible Grinder PumpSWG-200 Series
Features
Compact and light package, only 75 lbs.
Non-overloading design.
Externally mounted start components.
Mechanical seal: carbon/ceramic.
Deflection resistant, short motor shaft.
Corrosion resistant brass impeller minimizes downtime and maintenance.
Seven-vane, angled face, non-clogging, balanced impeller.
Tight cutting clearances for better cutting action.
Epoxy coated finish for corrosion resistance and durability.
Built-in overload protection prevents over-current and over-temperature damage.
GP-CK Grinder Capacitor Kit
To be used to operate SWG-200.
Includes:
Start capacitor.
Run capacitor.
Relay.
End caps.
Mounting hardware.
Grinder
75
SWG-200 Series 2 HP Manual Submersible Grinder Pump
Grinder
Shown with Stainless Steel GLK Series Grinder Leg Kit. See dealer for details.
5.50
11.40
9.63
5.75
2.98
9.30
11.50
16.10
13.10
Motor Cover Epoxy Coated Cast Iron
Motor Cover O-ring Nitrile
Motor DesignSingle-Phase, Capacitor Start, Capacitor Run
Insulation Class F
Overload ProtectionInternal, On Winding Thermal Protector
Motor Shaft AISI 300 SeriesStainless Steel
Upper Ball Bearing Single Row Ball, 6203
Lower Ball Bearing Single Row Ball, 6306
Seal Housing Epoxy Coated Cast Iron
Mechanical Seal Carbon/Ceramic
Volute Epoxy Coated Cast Iron
Impeller Brass
Rotating Cutter
Two Blade Design, AISI 440C Stainless Steel, Through Hardened to Rockwell 55-60C
Stationary Cutter
AISI 440C Stainless Steel, Through Hardened to Rockwell 55-60 °C
External Hardware300 SeriesStainless Steel
Power CableType SOOW orSOW 14/4 AWG
Construction
Specifications
0
20
60
120
40
80
140
100
0 5 10 15 20 25 30 35
FLOW - GALLONS/MINUTE
0.0
40.0
20.0
10.0
30.0
0 25 50 75 125100
FLOW - LITERS/MINUTE
HEA
D -
MET
ERS
HEA
D -
FEE
T
MODEL NO. ITEMNO. HP VOLTS DISCHARGE
SIZERUNNING
AMPS/WATTSPERFORMANCE (GPH) SHUT-OFF CORD
LENGTHWEIGHT
(LBS)20' 40' 60' 80' 100' 120' FEET PSI
SWG-200520854 2 208 1.25" FNPT 13.9/3200 32.0 31.0 30.0 25.0 20.0 10.0 130.0 65.0 15' 75.0520866 2 230 1.25" FNPT 13.9/2000 32.0 31.0 30.0 25.0 20.0 10.0 130.0 65.0 15' 75.0
SWG-200-AF 520876 2 230 1.25" FNPT 13.9/2000 32.0 31.0 30.0 25.0 20.0 10.0 130.0 65.0 20' 75.0