8
www.masermic.com EN_C_160419 46 . Datalogger with SMS / GSM / GPRS communication
www.masermic.com
EN_C_160419
46 . Datalogger with SMS / GSM / GPRS communication
Models
46
46D81 46D84 46D85DP 46D85
EN_C_160419
iLOGS46 is a data acquisition system that logs, manages and communi-
cates information via GSM/SMS/GPRS. It is an effective control solution
as it allows to send history logs or alarm messages and attend to exter-
nal communications.
iLOGS46 MEANS LONG LIFE Up to 6 years of autonomy (depending on the usage) powered by inter-nal batteries of 7,2V and 28A/h. It also has an external power input of 12V. iLOGS46 MEANS BIG MEMORY High-capacity data storage. 1Mb non-volatile memory that stores about 35.000 entries. iLOGS46 MEANS RUGGEDNESS IP67 or IP68 ruggedness in order to endure hostile environments (temperature, humidity, dirt, etc.). iLOGS46 MEANS EASE OF OPERATION iLOGS46 is rugged but accessible due to its reliable and easy connec-tions (IP68 connectors), front keypad with LEDs and parametrizable but-tons, as well as the intuitive software tools. All of this reduces consider-ably the installation and maintenance works. iLOGS46 MEANS FLEXIBILITY Wide range of applications, different input/output options, additional hardware and software compatible with other SCADAs.
GSM/SMS/GPRS communications
Up to 16 Digital / Analogical Inputs / Outputs
Up to 6 years of autonomy by batteries and external
12V input
IP67 and IP68 ruggedness
Monitoring software compatible with other
SCADAs
High-capacity data storage
Remote re-configuration and firmware re-programming
SMS messages to unlimited phone numbers
Tailored developments: we offer you our R&D capacity in order to reach the best solution for your needs.
The original
7,2V / 14Ah batteries
IP67 box
IP68 connectors
PLUS Autonomy
7,2V / 28Ah batteries
IP67 box
IP68 connectors
PLUS Ruggedness
7,2V / 28Ah batteries
IP68 box
IP68 connectors
PLUS Ruggedness
7,2V / 28Ah batteries
IP68 box
Internal pressure sensor
Operation
EN_C_160419
PROGRAMMING
iLOGS46 devices are configured in order to carry out some tasks or actions when an event or a repetition
pattern occurs.
LOGGING
iLOGS46 devices log values from sensors connected to analogical inputs.
GSM/SMS/GPRS COMMUNICATION
The information is sent via GSM/SMS/GPRS to a remote server or cell phones.
ACTUATION
It is possible to associate digital outputs to different devices (e.g: valves) in order to act when an event or a
repetition pattern occurs.
MONITORING
The remote server receives information from dataloggers. iDRIVER and iSOFT allow the management and
monitoring of information locally and in corporate networks. It is also possible to send the information by e
-mail from iSOFT.
SMS MESSAGES
iLOGS46 devices send SMS alarms and variables when an event or a repetition pattern occurs. It is also
possible to send unlimited SMS messages from iSOFT.
ACTUATION
It is possible to act over external devices (eg:
valves) programming the Digital Outputs
LOGGING
Example:
Temperature
PH
CO2
GSM/SMS/GPRS
COMMUNICATIONS
MONITORING
Example:
Databases
Graphics
GSM/GPRS alarms
SMS MESSAGES
Example:
SMS alarms
SMS variables
Aplications
iLOGS46 is designed to act in a wide range of sectors and applications. It can log values from 4-20mA or 0-10V transducers
and devices connected to its digital inputs, so it is possible to use iLOGS46 in every application with these characteristics.
As an example we have the following applications:
ENVIRONMENT
Crop control
Carbon emissions
Meteorological /
atmospheric control
Temperature and humidity
WATER
Water supply networks
Wastewater networks
Flow / pressure control
Irrigation control
Water quality
Water level
ENERGY
Electrical values
Energy efficiency
Hidrocarbons
Wind energy
Gas storage
management
MULTISECTORIAL
Preservation
Automation
Containers
Cage control
Hazardous materials
Fleet management
DIGITAL OUTPUTS
Latch relay
DIGITAL INPUTS
Dry contact or counters
ANALOGICAL INPUTS
4-20mA or 0-10V
MODBUS RTU
8 Digital Inputs
2 Analogical Inputs
POWER SUPPLY
7,2V 14A/h batteries
7,2V 28A/h battery box
External power supply
Technical Characteristics
EN_C_160419
PHYSICAL & ENVIRONMENTAL
Box IP67 or IP68 (optional).
Dimensions 180x130x50mm (changeable depending on the model). Weight 500 grams (changeable depending on the model). Temperature -20ºC to +60ºC. Humidity 95% (external condensation).
POWER SUPPLY
Internal battery Internal lithium battery: up to 7,2V – 28Ah (6 years of autonomy - 5min/day GSM/GPRS).
External power supply 12Vdc Input.
INPUTS/OUTPUTS
Local Inputs 8 Digital dry contact Inputs / 4 Analogic Inputs 4-20mA or 0-10V (12 bits).
4 Counters V & Q flank sensitives. (Frequency 10 Hz). Remote Inputs 8 Digital Inputs (MODBUS RTU) / 2 Analogic Inputs (MODBUS RTU).
Outputs 2 bi-stable latch Digital Outputs. U/O Dry contact (max 2A). 1 24Vdc Output (50 mA max).
COM port RS232 & RS485 MODBUS RTU. (9600 bauds, 8bits, 1 bit of stop, even parity)
I/O Options - 4 Dig. Inputs + 2 Analog. Inputs / 1 24Vdc Output - 4 Dig. Inputs + 2 Analog. Inputs / 2 Dig.Output + 1 24Vdc Output - 8 Dig. Inputs + 4 Analog. Inputs / 1 24Vdc Output
- 8 Dig. Inputs + 4 Analog. Inputs / 2 Dig. Outputs + 1 24Vdc Output
COMMUNICATIONS
GSM/GPRS Modem 850/900/1800/1900 MHz. GSM/GPRS Quad Band Modem GSM/GPRS Master The unit executes a call to dump the history log or send a GSM/GPRS/SMS alarm/message. GSM/GPRS Slave GSM/GPRS reception for interrogation or remote synchronisation/reconfiguration.
INTERNAL VARIABLES
FUNCTION ¿MODIFIABLE?
Clock & date Task synchronization and time-tag. Yes, locally and remotely.
Battery voltage Power supply remote supervision. Read only. Temperature Internal temperature remote supervision. Read only. Connector presence Configuration connector detection. Read only - Alarm.
Coverage level Remote supervision of GSM/GPRS coverage level. Read only. Battery charge Shows remaining battery %. Read only.
PROGRAMMING TOOLS
Task pattern Executes group of functions, events, data sampling or output settings.
Calculations Maximum, minimum, average, accumulated value, module value, time input active, +, -, x, /. Default events Serial connector plugged-in, memory overflow, low battery., configuration and firmware
update. User events Accepts the operators: =,>, <, <>, hysteresis operator, hysteresis complement, range and
Bolean values (true, false).
HISTORY LOGS
A configurable grouop of variables: Local or remote I/O, internal variables and calculation results.
A configurable group of alarm and events. Configurable data sampling frequency (advise: max every 15 seconds).
Configurable frequency between log-dumping (advise: min 5 minutes). All historical data is stored in 1Mb non-volatile memory (more than 35.000 records) upgradeable to 2Mb
KEYPAD OPTION
Leds Task (green).Comunication (amber). Status (red). Push-buttons Configurables, for manteinance and start up.
REF:iLOGS46-D8x-X-X-YYY-YY
(D8x= Model)
(X= Battery options)
(X= Keypad options)
(YYY= I/O options)
(YY= Analogical inputs options)
ORDERING INFORMATION
Model (see pag. 2) REF : D81 / D84 / D85
With internal battery / Without battery REF : X = A / X= B
With keypad / Without keypad REF : X = 1 / X=0
4 Dig. Inputs + 2 Analog. Inputs / 1 24Vdc Output REF : YYY = 420
4 Dig. Inputs + 2 Analog. Inputs / 2 Dig. Output + 1 24Vdc Output REF : YYY = 422
8 Dig. Inputs + 4 Analog. Inputs / 1 24Vdc Output REF : YYY = 840
8 Dig. Inputs + 4 Analog. Inputs/ 2 Dig. Outputs + 1 24Vdc Output REF : YYY = 842
Analogical Input 4-20 mA / 0-10V REF : YY = 20 / YY=10
FIABILIDAD DEL DETECTOR DE CAÍDAS
El algoritmo sensor de caídas ha superado satisfactoriamente los test más exigentes,
orientados a la solución de conflictos. Permite diferenciar con una alta eficacia entre caí-
das reales y falsas alarmas. Incorpora una base de datos de 505 tipos de caída y 321 falsas
alarmas.
EN_C_1600419
Hardware
EXTRA BATTERY BOX
7,2V - 14Ah @ 20ºC (1 battery)
7,2V - 28Ah @ 20ºC (2 batteries)
160x80x55mm
IP67
Direct connection to iLOGS46
Pollycarbonate box wirh 1 or 2 batteries. You should acquire if you want to increase the
autonomy of iLOGS46 or decentralize it.
REF : iLOGS46-PAP81 (1 battery)
iLOGS46-PAP82 (2 batteries)
EXTENDING ANTENNA
Short dipole
Quad Band
Gain: 3dBi
Resistence: 50Ω
Male SMA connector
Antena Extending antenna with 2.5-5m microaxial cable. You should acquire if you want to increase the
GSM/GPRS level in locations with low coverage.
REF : iLOGS46-AEE84
EXTERNAL BOX WITH TERMINALS
IP67 housing
160x80x55mm
Mini-terminal system
Direct connection to rail
IP68 cable glands
Terminal interface between iLOGS46’s connectors and sensors/actuators. You should
acquire if you have multiple wires connection and it is necessary a better accessibility.
REF : iLOGS46-CBR86
CONNECTION CABLES
PC-DATALOGGER communication cable
Power supply cable (to battery box)
External power supply cable
I/O cables
RS485 Modbus communication cable
Cables to connect iLOGS46 with other devices and peripherals. (PC, sensors, etc.). They are offered as a
standard but they can be made by users.
REF : iLOGS46-CXXXX
(XXXX=Consult cable references)
DESKTOP MODEM
Aluminum 63,5x63,5x9mm housing
Quad Band 850/900/1800/1900
USB 2,5 headset jack
Female SMA connector
Quad Band desktop modem to receive data through GSM/GPRS. You must acquire if you want to receive
data in your PC from iLOGS46 units.
REF : iLOGS46-MGS89CXXXX
EN_C_160419
Configuration & Monitoring Software
REF: iCONF46-XGE80
REF: iSOFT46-XGE81
REF: iDRIVER46-XGE82
iCONF46
The Configuration Software is the programming tool for iLOGS dataloggers. It uses multiple and powerful
combinations of tasks, events, actions, calculations, etc. Hence, users can develop the specific functioning of
their applications easily.
The program is divided in different programming steps in order to simplify the development of applications.
iCONF can be linked to iLOGS46 units in local format, based in RS485 connectivity or in remote format, based
in GSM communications.
ORDERING INFORMATION
iSOFT
iDRIVER
iDRIVER is a specific driver software to be used as an interface with SCADA software.
It integrates the Binary GSM/GPRS communications protocol for data communication between the PC server and the dataloggers.
Additionally to the specific driver functionality, it has some other functions in order to display received calls from iLOGS dataloggers, the communication status, events, logged values, etc.
iSOFT is a software for the management and monitoring of iLOGS dataloggers. This software tool is installed
in the PC server, and via GMS/GPRS communication allows to receive: alarms, the status of the dataloggers,
history logs, last received calls, the status of the batteries, etc.
iSOFT is a powerful tool to analyse values received from dataloggers as well as for a graphical visualization
of: history logs, trends, alarms, variables evolution , etc.
It is possible to manage a big number of dataloggers and the software has an utility to establish the commu-
nication time and period, making easier the organization.
The information is managed by ACCES or SQL Server databases.
Poligono Kurutz Gain 6A
20850 Mendaro - Gipuzkoa ( SPAIN )
Tel: +34 943 742669
www.masermic.com
EN_C_160419
The iLOGS product is a technological tool to support monitoring & control water & air parameters. Due to the nature of the technologies used, the correct operation can be conditioned by others. The Customer is informed and frees Microelectrónica Maser SL from any liability for damages arising from the non-reception, delay, error or interception of communications, lack of reading this notice or breach of specific obligations under the conditions set out therein.
