AAMCS S-band Amplifier

The Model Number AAMCS-20M-520M-40dB-47dBm is a solid state high power, class AB or A operation, broad-band, RF amplifier that covers 20 MHz to 520 MHz. Because this power amplifier offers high power over a multi-octave bandwidth, it is well suited for broadband commercial applications, laboratory or jamming applications. It is packaged in a modular housing that is approximately 250×125×50 mm. This amplifier offers a minimum gain of 39 dB with a typical gain flatness of ±1.5 dB, typical OIP3 is 50 dBm and a very fast rise time of 100 ns. This RF module requires an input voltage of 28 Vdc. Input/output RF connectors are N Female, SMA or TNC. DC and voltage com-mands are accessible via 6 pin bayonet connector. This amplifier has a typical P1dB of 50 watts at room temperature and operates from -40 °C to +85 °C.

• Operation from 20 MHz to 520 MHz • Small Signal Gain 39 dB minimum • Power flatness over full band

Electrical specifications Measuring Conditions Specifications

Bandwidth - 20 MHz - 520 MHz

Output power @P1dB Min. 46 dBm, Typ. 47 dBm

Maximum Input Power - Max. 5 dBm

Gain @P1dB Min. 39 dB Typ. 42 dB

Bandwidth ripple @P1dB ±1.5 dB

Input VSWR @P1dB Min 1.9:1, Typ 1.6:1

Output VSWR @P1dB Open OIp3 - Min. 48 dBm Typ. 50 dBm

Spurious Signal - -60 dBc

Consumption @ small signal @ 50 W 25°C Vcc = 28 V

Typ. 3 A Max. 4 A Typ. 6 A Max. 7 A

Length × Width × Height - 250 × 125 × 50 mm

PRESENTATION

FEATURES

SPECIFICATIONS

Specifications are subject to change without notice

AVAILABLE OPTIONS

• With or without heat sink cooler • SMA, BNC or TNC connectors type

• Other frequency range • Custom specification

OTHER FREQUENCY RANGE AVAILABLE

• AAMCS-20M-600M-40dB-44dBm, 20MHz-600MHz, G=40dB, Output P=44dBm, Consumption @small signal=1.5A Typ. • AAMCS-50M-1G-40dB-40dBm, 50MHz-1GHz, G=40 dB min, Output P=40 dBm, Consumption @small signal = 1.5 A Typ. • We can design from this basis, a custom product to fulfil your requirements

• Temperature protection

• Minimum output power of 46 dBm • Class AB or A operation

AA-MCS 18, rue Nicolas Appert 91898 ORSAY (France) Tel : 33 (0)1 76 91 50 12 Fax : 33 (0)1 76 91 50 31 www.aa-mcs.com

Broadband, High Power VHF/UHF Amplifier

AAMCS-AMP-20M-520M-40dB-47dBm

The Model Number AAMCS-10M-820M-48dB-30dBm is a solid state broadband amplifier that covers 10 MHz to 820 MHz. Because this amplifier offers power over a multi-octave bandwidth, it is well suited for broadband com-mercial applications, communication, laboratory or jamming applications. It is packaged in a compact and low weight modular housing that is approximately 80×40×24 mm of 130 g. This amplifier offers a minimum gain of 46 dB with a maximum gain flatness of ±1 dB, typical OIP3 is 47 dBm and minimum RF pulse width of 5 µs. This RF module requires an input voltage of 12 to 16 Vdc. Input/output RF connectors are SMA Female, and DC voltage commands are accessible via solderable feedthru. This amplifier has a minimum P1dB of 27 dBm at room tempera-ture and operates from -40 °C to +45 °C.

• Operation from 10 MHz to 820 MHz • Small Signal Gain 46 dB minimum • Power flatness over full band



Output power @P1dB, 25°C Vcc = 15 V Min. 27 dBm, Typ. 30 dBm

Gain 25°C Vcc = 15 V Min. 46 dB, Typ. 48 dB

Bandwidth ripple @P1dB, 25°C Vcc = 15 V ±1 dB

Input VSWR @P1dB, 25°C Vcc = 15 V Max. 2:1

Output VSWR @P1dB, 25°C Vcc = 15 V Max. 2.5:1

OIp3 @20 dB per carrier ∆f = 20MHz Min. 40 dBm, Typ. 47 dBm

Spurious Signal @Pout = 20 dBm Max. -70 dBc

Consumption @25°C, Vcc = 15 V Typ. 350 mA, Max. 400 mA


Noise Figure - Typ. 4 dB, Max 5 dB

PRESENTATION

FEATURES

SPECIFICATIONS


AVAILABLE OPTIONS




• AAMCS-10M-510M-46dB-27dBm, 10MHz-510MHz, G=49dB, Output P=30dBm, Max. ±0.6 dB bandwidth ripple. • AAMCS-800M-2.2G-44dB-27dBm, 800MHz-2.2 GHz, G=44 dB, Output P=30 dBm. • We can design from this basis, a custom product to fulfil your requirements

• Typical output power of 30 dBm • Maximum Noise Figure of 5 dB


Broadband VHF/UHF Amplifier


The Model Number AAMCS-AMP-380M-670M-11dB-45dBm is a class A, high power, linear RF amplifier that covers 380 MHz to 670 MHz. Due to its good linearity, it is well suited for TETRA (TErrestrial Trunked RAdio) applications such as emergency services or telecommunication, transport and government Private Mobile Radio networks. It is packaged in a small modular housing and offers a typical gain of 11 dB with a typical gain flatness of ±2 dB on the total bandwidth. Typical OIP3 is 52 dBm and input/output VSWR is 1.9:1 minimum. This RF module requires an input voltage of 12.5 V maximum. This amplifier is equipped with input/output RF connectors N female and TNC female respectively. It has a minimum P1dB of 45 dBm and can operate from -10 °C to +55 °C.

PRESENTATION

FEATURES

SPECIFICATIONS

TETRA 30 W Linear Amplifier


• Operation from 380 MHz to 670 MHz

• Class A operation

• Gain 10 dB minimum



Output power @P1dB Min. 43 dBm Typ. 45 dBm

Gain @P1dB Min. 10 dB Typ. 11 dB

Bandwidth ripple @P1dB Typ. ±2 dB Max. ±3 dB

Input/Output VSWR @P1dB Max 1.9:1

OIp3 2 tone, Pout = 5 W per carrier Min. 50 dBm Typ. 52 dBm

Spurious Signal @Pout = 10 W -60 dBc

Supply Voltage - Min. 10 V Typ. 12.5 V Max. 15 V

Consumption @25 °C Vcc = 12.5 V @Pout = 37 dBm Typ. 4 A Max. 6 A

Length × Width × Height Without heat-sink With heat-sink

120 × 80 × 27 mm 120 × 80 × 105 mm

AVAILABLE OPTIONS

• With or without heat-sink cooler • SMA, BNC or TNC connectors type • Temperature protection

• Extended bandwidth 380 MHz to 670 MHz available • Custom specification

• OIP3 of 52 dBm typical

• In-band spurious of -60 dBc



• We can design from this basis, a custom product to fulfil your requirements


PRESENTATION

FEATURES

SPECIFICATIONS

S-Band Auto Redundant Low Noise Amplifier



• Auto-redundant amplifier

• Small Signal Gain 50 dB minimum

• Noise Figure 0.9 max



Output power @P1dB Min. 15 dBm

Maximum Input Power Without any damage -30 dBm

Gain - Min. 50 dB

Bandwidth ripple On total bandwidth ±0.5 dB

Input/Output VSWR - Max 1.25:1

Noise Figure @25°C Max. 0.9

OIp3 - Min. 31 dBm Typ. 35 dBm

In-Band/Out-Band Spurious Signal - Max -100 dBc / -50 dBc

Consumption Vcc = 15 V Max. 100 mA


Noise Figure @25°C Typ. 0.9 Max

AVAILABLE OPTIONS


• Remote control by RS 485 • Custom specification


• AAMCS-2200M-2300M-50dB-15dBm, 2.2GHz-2.3GHz • AAMCS-2500M-2700MHz-50dB-15dBm, 2.5GHz-2.7GHz

• AAMCS-1700M-2000M-50dB-15dBm, 1.7GHz-2GHz • AAMCS-900M-1000M-40dB-40dBm, 0.9GHz-1GHz


• Power flatness over full band

• Entirely self-contained

• Control system module

The Model Number AAMCS-AMP-2025M-2120M-50dB-15dBm is an Outdoor, Low Noise, auto redundant, RF ampli-fier that covers 2025 MHz to 2120 MHz. This power amplifier is well suited for satellite communication reception ap-plications because low noise feature and redundant mode operation is offered. It is provided in a weatherproof enclo-sure packaged small modular housing and with a microcontroller card. It has a P1dB of 15 dBm minimum and offers a minimum gain of 50 dB ±0.5 dB on the total bandwidth for the main and redundant modules. Typical OIP3 is 35 dBm and input/output VSWR is 1.25:1 max. This RF module requires an input voltage of 15 V. Noise figure is to 0.9 maximum with input/output RF connectors SMA Female. This amplifier is able to operate in safety stand alone mode in extremely varying environment from -40 °C to +70 °C.


The Model Number AAMCS-1620M-1670M-45dB-48dBm is a solid state, class AB operation, power amplifier that covers 1620 MHz to 1670 MHz. This power amplifier has been developed for INMARSAT application and offers power in a compact package module of approximately 180×80×28 mm. This amplifier offers a minimum gain of 44 dB with a maximum gain flatness of ±1 dB, typical OIP3 is 55 dBm. This RF module requires an input voltage of 28±10% Vdc. Input/output RF connectors are N Female, and DC voltage command is accessible via 3 ways square flange connector. This amplifier has a minimum P1dB of 45 dBm at room temperature and operates from –20 °C to +70 °C.

• Operation from 1620 MHz to 1670 MHz • Small Signal Gain 44 dB minimum



Output power @P1dB, 25°C Vcc = 28 V Min. 45 dBm, Typ. 48 dBm

Gain @P1dB, 25°C Vcc = 28 V Min. 44 dB, Typ. 45 dB

Bandwidth ripple @P1dB, 25°C Vcc = 28 V Typ. 0.5 dB, Max. ±1 dB

Input VSWR @P1dB, 25°C Vcc = 28 V Min. 14 dB

Output VSWR @P1dB, 25°C Vcc = 28 V Min. 14 dB

OIp3 @30 W Min. 53 dBm, Typ. 55 dBm

Spurious Signal @P1dB Max. -60 dBc

Consumption @25°C, Vcc=28V, Small Signal @25°C, @Pout=45dBm

Typ. 1.5 A, Max. 2.5 A Typ. 4 A, Max. 5 A


PRESENTATION

FEATURES

SPECIFICATIONS


AVAILABLE OPTIONS





• Typical output power of 48 dBm


Power Amplifier


The Model Number AAMCS-AMP-2500M-2700M-50dB-46dBm is a Solid State Power Amplifier for an outdoor oper-ating purpose in the S-band frequencies. This amplifier has been designed for antenna mount integrations and is well suited for satellite communication systems, telemetry and tracking applications. It is provided in a weatherproof en-closure with a complete power supply, a filter and a microcontroller card. Output saturated power reaches 46 dBm typically, with a minimum gain of 50 dB ±1 dB on the total bandwidth. Input/output VSWR is 1.3:1/1.4:1 max. This RF module requires an input voltage of 220 Vac(±10%)/50 Hz. This amplifier is able to operate in safety stand alone mode in extremely varying environment from -40 °C to +60 °C. It is equipped with SMA-K and N female connectors type in input and output respectively.

PRESENTATION

FEATURES

SPECIFICATIONS

Outdoor S-Band Power Amplifier



• Minimum Gain 45 dB

• Minimum output power of 45 dB

• Noise Figure 6 max




Gain - Min. 45 dB Typ. 50 dB

Bandwidth ripple On the total bandwidth ±1 dB

Gain Slope /50 MHz Max. ±0.5 dB

Gain stability @25 °C ±5 °C ±0.25 dB dB/24h

Gain control Step: 0.1 dB 30 dB

Input VSWR Output VSWR - Max 1.3:1

Max 1.4:1

Intermodulation distorsion @P1dB -4 dBm Max. -28 dBc

Spurious Signal Pout = 45 dBm Max. -70 dBc

Consumption @Pout = 45 dBm Max. 300 W


AVAILABLE OPTIONS

• Remote control by RS 485 • Module alarms

• 1+1 redundant configuration • Custom specification

• Design for convenient integration







PRESENTATION

FEATURES

SPECIFICATIONS

Outdoor S-Band Auto Redundant High Power Amplifier

AVAILABLE OPTIONS


• Custom specification


• 1+1 redundant amplifier





Output power @P1dB and @25°C Min. 48 dBm Typ. 50 dBm


Bandwidth ripple On total bandwidth ±0.5 dB


Gain stability @25 °C ±5 °C Max. ±0.25 dB/24h



Intermodulation distorsion @P1dB -4 dB -28 dBc

Spurious Signal @P1dB Max. –80 dBc

Consumption @P1dB per amplifier Typ. 300 W Max 480 W









The Model Number AAMCS-AMP-2500M-2700m-70dB-50dBm is a Solid State High Power Amplifier for outdoor pur-pose in the S-band frequencies. This amplifier is reliable, manufactured for uninterrupted services with its redundant configuration. Designed for antenna mount integration, it is well suited for Satellite Communication systems, teleme-try and tracking applications. It is provided in a weatherproof enclosure with a complete power supply, a filter and a microcontroller card. Output saturated power reaches 50 dBm typically, with a minimum gain of 68 dB and a typical gain flatness of ±0.5 dB on the total bandwidth for the main and redundant modules. Input/output VSWR is 1.2:1 max. This RF module is equipped with N female connectors type, requires an input voltage of 220 Vac/50 Hz and can operate from -40 °C to +60 °C.



The Model Number AAMCS-AMP-2500M-2700m-53dB-50dBm is a Solid State High Power Amplifier for outdoor pur-pose in the S-band frequencies. This amplifier is reliable, manufactured for uninterrupted services with its redundant configuration. Designed for antenna mount integration, it is well suited for Satellite Communication systems, teleme-try and tracking applications. It is provided in a weatherproof enclosure with a complete power supply, a filter and a microcontroller card. Output saturated power reaches 50 dBm typically, with a minimum gain of 50 dB and a typical gain flatness of ±1 dB on the total bandwidth for the main and redundant modules. Input/output VSWR is 1.3:1/1.4:1 max. This RF module is equipped with N female connectors type, requires an input voltage of 230 Vac/50 Hz and can operate from -40 °C to +60 °C.

PRESENTATION

FEATURES

SPECIFICATIONS



Output power @P1dB and @25°C Min. 49 dBm Typ. 50


Bandwidth ripple On total bandwidth ±1 dB




Input VSWR Output VSWR - Max 1.3:1

Max 1.4:1

Intermodulation distorsion @P1dB -4 dB -28 dBc


Consumption Pout = 45 dBm Max. 700 W


AVAILABLE OPTIONS




• 1+1 redundant amplifier










Outdoor S-Band Auto Redundant High Power Amplifier AAMCS-AMP-2500M-2700M-53dB-50dBm


The Model Number AAMCS-AMP-2200M-2300M-68dB-54dBm is a Solid State High Power Amplifier for an outdoor operating purpose in the S-band frequencies. This amplifier has been designed for antenna mount applications such as satellite communication systems, telemetry and tracking applications. It is provided in a weatherproof enclosure with a complete power supply, a filter and a microcontroller card. Output saturated power reaches 54 dBm typically, with a minimum gain of 65 dB and a typical gain flatness of ±1 dB on the total bandwidth. Input/output VSWR is 1.25:1 max. This RF module requires an input voltage of 220 Vac(±10%)/50 Hz. It is able to operate in safety stand alone mode in extremely varying environment from -40 °C to +60 °C. It is equipped with SMA-K and N female con-nectors type for the input and output respectively.

PRESENTATION

FEATURES

SPECIFICATIONS

Outdoor S-Band High Power Amplifier









Bandwidth ripple 0n the total bandwidth ±1 dB





Intermodulation distorsion @P1dB -3dB Max. –28 dBc


Consumption @P1dB Max. 880 W


AVAILABLE OPTIONS


• 1+1 redundant configuration • Custom specification









PRESENTATION

SPECIALITIES

AA-MCS-SYSTEM

AVAILABLE OPTIONS

For the integration of complex sub-systems and systems, AA MCS counts on the complementary partnerships it has with its specialized staff in the passive and active product lines and in manuracturing. Our company is able to offer a total solution for its customers, for which the technical specifications correspond precisely to their needs. AA-MCS is a solutions provider, proposing our services for the assembly of “turn-key” systems, for which our inter-disciplinary nature is well adapted for the integration of complex systems and sub-systems. AA-MCS offer project studies, design, and production of modules, systems and sub-systems, from prototyping up to mass production. For each project study, a prototype is developed followed by a thorough series of tests and meas-urements.

• Transceivers and receivers modules • Repeaters • Distributed Switches modules • Switches bank filters • Test bench and system • Telemetry system • Multi-coupler rack mounted • Custom-designed subsystems to customer specification

• Rack mounting unit • 19” bench top unit • Modular

• RS485/RS422 and 10/100 Base-T Ethernet remote control

• Weatherproof enclosure • Custom configuration

Integration solutions from 20 MHz to 20 GHz


Date post:	05-Dec-2015
Category:	Documents
Upload:	mazlum-uenal
View:	7 times
Download:	1 times

AAMCS S-band Amplifier

Documents