Date post: | 11-Dec-2015 |
Category: |
Documents |
Upload: | ahmed-ismail |
View: | 282 times |
Download: | 30 times |
CASE 1 1 BTS HPMI/TCU/Alarm BoardCOM OUT
COM IN COM OUT TEST
PMUBBU
FMUACOM IN COM OUT
in this case Alarms will be reported through the 2G of the BBU3900
COM IN
MON 1 MON 0
in this case Alarms will be reported through the 2G of the BBU3900
CAB 12 BTS HPMI/TCU/Alarm Board HPMI/TCU/Alarm Board
COM OUT COM IN
COM IN COM IN
PMU
BBUMON 1 MON 0
FAN 01ACOM OUT COM IN
in this case Alarms will be reported through the 2G of the BBU3900
CAB 2HPMI/TCU/Alarm Board
COM OUT COM IN
PMU
FAN 01ACOM OUT COM IN
in this case Alarms will be reported through the 2G of the BBU3900
HPMI/TCU/Alarm BoardCOM OUT
COM IN COM OUT COM485
PMUBBU
TCU in BBC cabinetCOM IN COM OUT
Kindly find below cables connection needed to report APM and BBC alarms trough 3G BBU, noting that it should be configured from 3G BO side to adjust the cabinets number also the communication address to be matched with site old configuration.
COM IN
MON 1 MON 0
Kindly find below cables connection needed to report APM and BBC alarms trough 3G BBU, noting that it should be configured from 3G BO side to adjust the cabinets number also the communication address to be matched with site old configuration.
Kindly find below cables connection needed to report APM and BBC alarms trough 3G BBU, noting that it should be configured from 3G BO side to adjust the cabinets number also the communication address to be matched with site old configuration.
CAB 12 BTS HPMI/TCU/Alarm Board HPMI/TCU/Alarm Board
COM OUT COM IN
COM IN COM IN
PMU
BBUMON 1 MON 0
FAN 01ACOM OUT COM IN
in this case Alarms will be reported through the 2G of the BBU3900
CAB 2HPMI/TCU/Alarm Board
COM OUT COM IN
COM OUT COM45
PMU
TCU in BBC cabinetCOM IN COM OUT
in this case Alarms will be reported through the 2G of the BBU3900
HPMI/TCU/Alarm BoardCOM OUT COM IN
COM IN COM OUT TEST
PMUBBU
MON 1 MON 0
1
2
3
4
5
ADD PMU: CN=0, PTYPE=APM30, MPN=1, LSDF=DISABLE;ADD PSU: CN=0, SN=1;ADD PSU: CN=0, SN=2;ADD PSU: CN=0, SN=3;ADD TCU: CN=0, MPN=1;ADD BATTERY: CN=0, INSTALLTYPE=OUTER, BN=1, BC1=5, HTSDF=ENABLE, LVSDF=ENABLE;foc CMCTRL ( 1 )
CN .. cabinet numberPTYPE .. power system typeMPN .. manager port numberLSDF .. load shutdown flag
monitoring APM30 alarms through CSH card in RTN950
HPMI/TCU/Alarm BoardCOM OUT COM IN
COM IN COM OUT COM485
PMURTN950
CSH TOD2 slot
TCU in BBC cabinetCOM IN COM OUT
1
2
3
4
5
We can report the following alarms of mini shelter cabinet through EMUA:
EMUA
Item Item Description Revision QTY Phase
UNHW10221NOutdoor Environment Monitoring Module 1
Alarm ID Alarm Name
25672
25671 Smoke Alarm
25651
25650
And for TEC fault alarm we should define it as it is customized alarm as below MML commands after we connect it is alarm cable to S1+, S1- of the EMUA board:
Alarm ID
65080
Alarm ID Alarm Name
25672
25671
Ø 1st solution for reporting mini shelter alarms:
· Steps:
Burglar Alarm
Ambient Humidity
Unacceptable
Ambient Temperature Unacceptable
Alarm Name
Battery Cabinet
TEC Fault
Ø 2 nd solution for reporting mini shelter alarms:
Burglar Alarm
Smoke Alarm
25671
25651
25650
And for TEC fault alarm we should define it as it is customized alarm as below MML commands after we connect it is alarm cable to S1+, S1- of the EMUA board:
Alarm ID
65080
Smoke Alarm
Ambient Humidity
Unacceptable
Ambient Temperature Unacceptabl
e
Alarm Name
Battery Cabinet
TEC Fault
EMUA
Vendor Code
2237276
And for TEC fault alarm we should define it as it is customized alarm as below MML commands after we connect it is alarm cable to S1+, S1- of the EMUA board:
And for TEC fault alarm we should define it as it is customized alarm as below MML commands after we connect it is alarm cable to S1+, S1- of the EMUA board:
The b/m scenario that can be used in 3G DBS3900 as alternative scenario for EMUA in order to report Mini shelter alarms using HPMI board.
below alarms reported and tested during trial.
Note:
Ø 2 nd solution for reporting mini shelter alarms:
1- Temperature &Humidity alarm .
2- Smoke alarm.
3- Gate alarm(cascaded with APM door alarm to be reported if any cabinet door opened.
4- Battery Cabinet TEC Fault alarm ( defined as dry contact alarm with ALM ID: 65080 same as 2G to be unified alarm code on U2000).
· These alarms can be adjusted from my side while creating the XML file for customer sites.
· Below the ports connections for each of a/m alarms.
The b/m scenario that can be used in 3G DBS3900 as alternative scenario for EMUA in order to report Mini shelter alarms using HPMI board.
Gate alarm(cascaded with APM door alarm to be reported if any cabinet door opened.
Battery Cabinet TEC Fault alarm ( defined as dry contact alarm with ALM ID: 65080 same as 2G to be unified alarm code on U2000).
These alarms can be adjusted from my side while creating the XML file for customer sites.
Dear Teams;
Please refer to the attached guide section 4.3.7 Connecting to Huawei BBU (over Dry Contacts, M2000 Management).
We can manage ETP48200 through NETECO server without additional hardware after providing the following for IP network creation:
Kindly find the below 2 solutions to connect the alarms of mini shelter for RTN980:
· Solution 1:
· Solution 2:
Ø IP for each node.Ø Create Vlan for each node.Ø IP route creation between each node and NETECO server IP 10.74.172.41 / Port:8086 .
Please refer to the attached guide section 4.3.7 Connecting to Huawei BBU (over Dry Contacts, M2000 Management).
We can manage ETP48200 through NETECO server without additional hardware after providing the following for IP network creation:
IP route creation between each node and NETECO server IP 10.74.172.41 / Port:8086 .