AN
CHORING
D
OWELING
AN
CHORING
D
OWELING
ULTRABOND® HS-1CCHigh StrengthEpoxy Adhesive
GENERAL USES & APPLICATIONS
• Anchor in dry, water saturated, water-filled and submerged hammer drilled holes
• Suitable for core drilled installations in dry or water saturated concrete
• Muliple anchor types: threaded rod, rebar & internally threaded inserts
• OSHA Table 1 compliant drilling/cleaning method using Milwaukee Tool hollow vacuum bit system
www.atcepoxy.com 1.800.892.1880
ADVANTAGES & FEATURES
• IAPMO ER-591 evaluation report for use in cracked and uncracked normal weight and lightweight concrete
• Code Compliant in cartridge and bulk dispensing systems, IBC/IRC: 2018, 2015, 2012 & 2009
• Highest elevated temperature resistance of any ICC-ES AC308 and ACI 355.4 assessed anchoring epoxy on the market, up to 205 °F (96 °C) under short term loading conditions
• Made in the USA
STANDARDS & APPROVALSCODE COMPLIANT:IAPMO UES ER-591
IBC/IRC 2018, 2015, 2012 & 2009Florida Building Code 2017 & 2014
City of Los Angeles - Report Pending
Drinking Water System Components NSF/ANSI 61 & 372
AASHTO M235 / ASTM C881-15Type I, II, IV & V Grade 3 Class A, B & C
Nationally Department of Transportation (DOT)Approved or Pending
HIGHEST PERFORMINGANCHORING EPOXY
− PERIOD −
ER-591
The first and only Code Compliant anchoring adhesive approved for
bulk dispensing systems!
ATC Hilti ITW DeWalt
ER-591 ESR-3814 ESR-4057 ESR-2508 ESR-4046 ESR-3298
Threaded Rod, Rebar & Internally Threaded Inserts
Fast Full Cure @ 75 °F in 7 hours or less
Dry, Damp, Water-Filled and Submerged Holes
Concrete Gray Color
Highest Average Bond Strength
NSF / ANSI 61 & 372Drinking Water & Lead Free
Core-Drilled Holes (SD)
Cartridge & BulkCode Compliant
Highest Temperature Epoxy = 205 °F
Pure110+
Convenient 1:1 Mix Ratio
SET-3G
ICC AC308 & ACI 355.4 Tested and Assessed
ULTRABONDHS-1CC
RE 500 V3
Simpson
SET-XPRedhead
C6+
No Hole Cleaningw/Vacuum Drill Bits
Competitive Advantages
www.atcepoxy.com 1.800.892.1880Rev 112018
THE CHOICE IS CLEAR
Hilti is a registered trademark of Hilti Aktiengesellschaft Corporation | Simpson, SET-XP & SET-3G are registered trademarks of Simpson Strong-Tie Company, Inc. ITW Red Head is a registered trademark of Illinois Tool Works, Inc. | Pure110+ & DeWalt are trademarks of Stanley Black & Decker
Data Sources for Products in Illustrated Graphs: ER-591, Issued August 2018 | ESR-3298, Reissued July 2018 | ESR-3814, Revised May 2018 ESR-3577, Revised February 2018 | ESR-4046, Reissued September 2018 | ESR-4057, Issued April 2018 | ESR-2508, Reissued July 2018
For complete product information, please refer to the product TDS at www.atcepoxy.com.
BOND STRENGTH IN DRY CRACKED CONCRETE, THREADED ROD, 176 °F+ SHORT TERM
TEMPERATURE*, WITH SUSTAINED LOAD AND PERIODIC INSPECTION
HS-1CC Pure110+ RE 500 V3C6+
(2k Polymer)SET-3G
11.5% 41.5% 0.375 1,245 882 880 453 1,11710.7% 43.1% 0.625 1,245 882 870 453 1,1250.5% 22.7% 0.875 1,055 882 860 453 1,050
19.7% 38.3% 1.25 1,120 882 810 453 936
HS-1CC 13%Pure110+ 0%RE 500 V3 0%C6+ (2KP) 27%C6+ (2:1) 4%SET-3G 0%SET-XP 42%
HS-1CC 130 to 180 Max Temp:Pure110+ 140 to 176RE 500 V3 130 to 176C6+ (2KP) 130 to 176C6+ (2:1) 142 to 165SET-3G 160 to 176
SET-XP
Cracked Dry Concrete, Threaded Rod, Periodic Inspection, With Sustained Load, 176F+ Short Term
* Note: ITW C6+ (new 2:1) is limited to a maximum short term temperature of only 165 °F, and Simpson SET-XP is limited to a maximum short term temperature of only 150 °F, therefore neither meet the performance characteristics necessary in order to compare in this chart to the higher temperature performing products.
% Better than Hilti RE
500 V3
Anchor Size
180F with sust. Load
176F with sust. Load
176F with sust. Load
% Better than Simpson SET-
3G
Only Publish 1 Temperature Range(capped at 150F)
12%27%31%46%15%17%
176F with sust. Load
Reductions Due to Sustained Load
Reductions Due to Short Term Elevated Temperature
Temp Range A to B/C
176F with sust. Load
0
200
400
600
800
1,000
1,200
1,400
0.375 0.625 0.875 1.25
Bond
Str
engt
h (p
si)
Threaded Rod Diameter (inch)
Bond Strength in Dry Cracked Concrete, Threaded Rod, 176 °F+ Short Term
Temperature*, with Sustained Load and Periodic Inspection
HS-1CC
Pure110+
RE 500 V3
C6+ (old 1:1)
SET-3G
HS-1CC
Pure 110+
RE 500 V3
SET-3G
C6+ (old 1:1)
C6+ (new 2:1)
SET-XP
* Note: ITW C6+ (new 2:1) is limited to a maximum short term temperature of only 165 °F, and Simpson SET-XP is limited to a maximum short term temperature of only 150 °F, therefore neither meet the performance characteristics necessary in order to compare in this chart to the higher temperature performing products.
BOND STRENGTH IN DRY UNCRACKED CONCRETE, THREADED ROD, ≤ 160 °F SHORT TERMTEMPERATURE, NO SUSTAINED LOAD
AND PERIODIC INSPECTION
HS-1CC Pure110+ RE 500 V3C6+
(2k Polymer)C6+
(New 2:1)SET-3G SET-XP
16.2% 20.6% 0.375 2,870 1,829 2,380 1,350 2,470 2,192 1,33014.3% 19.7% 0.625 2,645 1,671 2,210 1,350 2,315 2,162 1,83012.0% 18.6% 0.875 2,420 1,567 2,040 1,350 2,160 1,967 1,5257.8% 16.2% 1.25 2,080 1,479 1,790 1,350 1,930 1,672 1,070
ReferencesComments
ESR-3298ESR-3814ESR-3577 27% increase without sustained loadESR-4046 4% increase without sustained loadESR-4057ESR-2508 42% increase without sustained load
160F w/o sust. Load% Better
than Hilti RE 500 V3
Uncracked Dry Concrete, Threaded Rod, Periodic Inspection, No Sustained Load, ≤ 160F Short Term
% Better than ITW C6+
Anchor Size
150F w/o sust. Load
140F w/o sust. Load
130F w/o sust. Load
Revised February 2018 ITW C6+ (2KP formula)Revised Sept. 6th, 2017 ITW C6+ (new 2:1 formula)Issued April 2018 Simpson SET-3G No difference in sustained vs. no sustainedRevised February 2018 Simpson SET-XP
150F w/o sust. Load
Revised February 2018 DeWalt Pure110+ No difference in sustained vs. no sustainedRevised December 2017 Hilti RE 500 V3 No difference in sustained vs. no sustained
130F w/o sust. Load
142F w/o sust. Load
0
500
1,000
1,500
2,000
2,500
3,000
0.375 0.625 0.875 1.25
Bond
Str
engt
h (p
si)
Threaded Rod Diameter (inch)
Bond Strength in Dry Uncracked Concrete, Threaded Rod, ≤ 160 °F Short Term
Temperature, No Sustained Load and Periodic Inspection
HS-1CC
Pure110+
RE 500 V3
C6+ (old 1:1)
C6+ (new 2:1)
SET-3G
SET-XP
ULTRABOND®HS-1CCER-591
RE 500 V3ESR-3814
SET-3GESR-4057
SET-XPESR-2508
RedheadC6+
ESR-4046Pure 110+ESR-3298
HS-1CC
Pure 110+
RE 500 V3
SET-3G
C6+ (old 1:1)
7 hours