CATIA V5R15 Course Catalog

CATIA V5R15Course Material Catalog

May 2005 Edition

CATIA V5R15 Course Material Catalog May 26, 2005 1/102

CATIA V5R15 Course Material Catalog

CATIA Course Material ..................................................... 5Analysis Solutions ....................................................................... 5

EST: ELFINI Structural Analysis (EDU-CAT-E-EST-F - V5R15) ............................................. 6FMD: FEM Solid (EDU-CAT-E-FMD-F - V5R15) ..................................................................... 7FMS: FEM Surface (EDU-CAT-E-FMS-F - V5R15) ................................................................. 8GAS: Generative Assembly Structural Analysis (EDU-CAT-E-GAS-F - V5R15) ................... 10GAS: Generative Assembly Structural Analysis V5R15 Update (EDU-CAT-E-GAS-U - V5R15)GDY: Generative Dynamic Response Analysis (EDU-CAT-E-GDY-F - V5R15) .................... 12GPE: Generative Part Structural Analysis Expert (EDU-CAT-E-GPE-F - V5R15) ................. 13GPF: Generative Part Structural Analysis Fundamental (EDU-CAT-E-GPF-F - V5R15) ...... 14GPS: Generative Part Structural Analysis V5R15 Update (EDU-CAT-E-GPS-U - V5R15) ... 15TAA: Tolerance Analysis of Deformable Assembly (EDU-CAT-E-TAA-F - V5R15) ............... 16

Equipment & Systems Engineering Solutions ................................ 17CBD: Circuit Board Design (EDU-CAT-E-CBD-F - V5R15) ................................................... 18EHF: Electical Harness Flattening (EDU-CAT-E-EHF-F - V5R15) ........................................ 19EHI: Electrical Harness Installation (EDU-CAT-E-EHI-F - V5R15) ........................................ 20ELB: Electrical Librarian (EDU-CAT-E-ELB-F - V5R15) ........................................................ 21EWR: Electrical Wire Routing (EDU-CAT-E-EWR-F - V5R15) .............................................. 22TUB: Tubing Design (EDU-CAT-E-TUB-F - V5R15) .............................................................. 23TUD: Tubing Diagrams (EDU-CAT-E-TUD-F - V5R15) ......................................................... 24TUS: Tubing Catalogs (2D Diagrams & 3D Design) (EDU-CAT-E-TUS-A - V5R15) ............. 25

Infrastructure Solutions ............................................................. 27ADM: V5 Administration (EDU-CAT-E-ADM-F - V5R15) ....................................................... 28PRO: CATIA Tools For Proficient Users (EDU-CAT-E-PRO-F - V5R15) .............................. 29V4I: V4 Integration (EDU-CAT-E-V4I-F - V5R15) .................................................................. 30V4I: V4/V5 Advanced Interoperability (EDU-CAT-E-V4I-A - V5R15) ..................................... 31VBA: CATIA V5 Automation (EDU-CAT-E-VBA-F - V5R15) .................................................. 32

Mechanical Design Solutions ...................................................... 33ASL: Aerospace Sheet Metal Design (EDU-CAT-E-ASL-F - V5R15) .................................... 34ASM: CATIA Product Design Expert (EDU-CAT-E-ASM-A - V5R15) .................................... 35CCV: Core & Cavity Design (EDU-CAT-E-CCV-F - V5R15) .................................................. 36DDR: CATIA Detail Drafting (EDU-CAT-E-DDR-F - V5R15) ................................................. 37DRA: Advanced Drafting (EDU-CAT-E-DRA-A - V5R15) ....................................................... 38FMP: Functional Molded Part (EDU-CAT-E-FMP-F - V5R15) ............................................... 39FR1: Part Design Feature Recognition (EDU-CAT-E-FR1-F - V5R15) ................................. 41FTD: 3D Functional Tolerancing & Annotation (EDU-CAT-E-FTD-F - V5R15) ...................... 42GS1: CATIA Surface Design (EDU-CAT-E-GS1-F - V5R15) ................................................. 44HA1: Healing Assistant (EDU-CAT-E-HA1-F - V5R15) .......................................................... 45LO1: 2D Layout to 3D Design (EDU-CAT-E-LO1-F - V5R15) ................................................ 46MD2: CATIA Mechanical Design V5R15 Update (EDU-CAT-E-MD2-U - V5R15) ................. 47MTD: Mold Tooling Design (EDU-CAT-E-MTD-F - V5R15) ................................................... 48


PDG: CATIA Part Design Expert (EDU-CAT-E-PDG-A - V5R15) .......................................... 49SMD: CATIA Generative Sheet Metal Design (EDU-CAT-E-SMD-F - V5R15) ...................... 50SMD: CATIA Generative Sheetmetal Design V5R15 Update (EDU-CAT-E-SMD-U - V5R15)SR1: Structure Design (EDU-CAT-E-SR1-F - V5R15) ........................................................... 52SR1: Structure Design (EDU-CAT-E-SR1-A - V5R15) .......................................................... 54TG1: Tooling Design (EDU-CAT-E-TG1-F - V5R15) ............................................................. 55V5E: CATIA V5 Expert Mechanical Designer (EDU-CAT-E-V5E-A - V5R15) ........................ 56V5F: CATIA V5 Fundamentals (EDU-CAT-E-V5F-F - V5R15) .............................................. 58

Machining Solutions .................................................................. 60AMG: Advanced Part Machining (EDU-CAT-E-AMG-F - V5R15) .......................................... 61LMG: Lathe Machining (EDU-CAT-E-LMG-F - V5R15) .......................................................... 62MMG: Multi-Axis Surface Machining (EDU-CAT-E-MMG-F - V5R15) ................................... 63MPA: Prismatic Machining Preparation Assistant (EDU-CAT-E-MPA-F - V5R15) ................ 64MPG: Multi Pocket Machining (EDU-CAT-E-MPG-F - V5R15) .............................................. 65NCI: Numerical Control Infrastructure (EDU-CAT-E-NCI-F - V5R15) .................................... 66PMG: Prismatic Machining (EDU-CAT-E-PMG-F - V5R15) ................................................... 68SMG: Surface Machining (EDU-CAT-E-SMG-F - V5R15) ..................................................... 69STL: STL Rapid Prototyping (EDU-CAT-E-STL-F - V5R15) .................................................. 71

Product Synthesis Solutions ....................................................... 72HMN: Human Modeling (EDU-CAT-E-HMN-F - V5R15) ........................................................ 73KWA: Knowledge Advisor (EDU-CAT-E-KWA-F - V5R15) .................................................... 74KWE: Knowledge Expert (EDU-CAT-E-KWE-F - V5R15) ...................................................... 75KWF: Knowledge Fundamentals (EDU-CAT-E-KWF-F - V5R15) .......................................... 76PEO: Product Engineering Optimizer (EDU-CAT-E-PEO-F - V5R15) ................................... 77

Shape Design & Styling Solutions ................................................ 78DL1: Developed Shapes (EDU-CAT-E-DL1-F - V5R15) ........................................................ 79DSE: Digitized Shape Editor (EDU-CAT-E-DSE-F - V5R15) ................................................. 80FSK: FreeStyle Sketch Tracer (EDU-CAT-E-FSK-F - V5R15) ............................................... 81FSS: FreeStyle Shaper, Optimizer & Profiler (EDU-CAT-E-FSS-F - V5R15) ........................ 82GSD: Surface Design Expert (EDU-CAT-E-GSD-F - V5R15) ................................................ 83GSD: CATIA Generative Shape Design V5R15 Update (EDU-CAT-E-GSD-U - V5R15) ...... 84GSO: Generative Shape Optimizer (EDU-CAT-E-GSO-F - V5R15) ...................................... 85IMA: Imagine & Shape (EDU-CAT-E-IMA-F - V5R15) ........................................................... 86PHS: Photo Studio (EDU-CAT-E-PHS-F - V5R15) ................................................................ 88PSO: Photo Studio Optimizer (EDU-CAT-E-PSO-F - V5R15) ............................................... 89QSR: Quick Surface Reconstruction (EDU-CAT-E-QSR-F - V5R15) .................................... 90RTR: Real Time Rendering (EDU-CAT-E-RTR-F - V5R15) ................................................... 91

Digital Mock-Up Course Material ...................................... 92Digital Mock-Up Solutions .......................................................... 92

ANR: DMU Engineering Analysis Review (EDU-DMU-E-ANR-F - V5R15) ........................... 93DMB: Digital Mock Up Basics (EDU-DMU-E-DMB-F - V5R15) .............................................. 94


DMB: Digital Mock Up Basics V5R15 Update (EDU-DMU-E-DMB-U - V5R15) ..................... 95DMN: Digital Mock Up Navigator (EDU-DMU-E-DMN-F - V5R15) ........................................ 96DMN: Digital Mock Up Navigator V5R15 Update (EDU-DMU-E-DMN-U - V5R15) ............... 97DMO: Digital Mock Up Optimizer (EDU-DMU-E-DMO-F - V5R15) ........................................ 98FIT: Digital Mock-Up Fitting Simulator (EDU-DMU-E-FIT-F - V5R15) ................................... 99KIN: Digital Mock-Up Kinematics Simulator (EDU-DMU-E-KIN-F - V5R15) ........................ 100SPA: Digital Mock Space Analysis (EDU-DMU-E-SPA-F - V5R15) ..................................... 101SPA: Digital Mock Space Analysis V5R15 Update (EDU-DMU-E-SPA-U - V5R15) ............ 102


CATIA Course Material

Analysis Solutions

CATIA V5R15 Course Catalog May 26, 2005 5/102

AnalysisSolutions EST: ELFINI Structural Analysis

EDU-CAT-E-EST-FCourse Code EDU-CAT-E-EST-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EST-FI-V5R15 Foils: EDU-CAT-E-EST-FF-V5R15 Exercises: EDU-CAT-E-EST-FX-V5R15 Detailed Steps: EDU-CAT-E-EST-FS-V5R15

ObjectivesIn this course, you will discover the advanced functionalities of ELFINIStructural Analysis

Participants' ProfileCATIA V5 users

PrerequisitesGenerative Part & Assembly Structural AnalysisStructural Analysis, FMS

Content- Advanced Pre-Processing- Advanced Analysis Case Management- Advanced Post-Processing- EST Functionalities

ExercisesEx. 1: Advanced Analysis of Landing Gear Assembly (120min) / AerospaceEx. 2: Bearing loads Analysis (10min) / All sectorsEx. 3: Hanger Buckling Analysis (15min) / All sectorsEx. 4: Door Fuselage Buckling Analysis (30min) / AerospaceEx. 5: Pressure Contact between Rod and Axis (20min) / AutomotiveEx. 6: Blade Analysis (120min) / AerospaceEx. 7: Truss Analysis (120min) / All sectorsEx. 8: Toy surfacic Analysis (120min) / Fabrication & Assemblies ConsumerGoodsEx. 9: Static constrained modes / All sectorsEx. 10: Adaptivity (120min) / All sectorsEx. 11: Automation (30min) / All sectors


AnalysisSolutions FMD: FEM Solid

EDU-CAT-E-FMD-FCourse Code EDU-CAT-E-FMD-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMD-FI-V5R15 Foils: EDU-CAT-E-FMD-FF-V5R15 Exercises: EDU-CAT-E-FMD-FX-V5R15 Detailed Steps: EDU-CAT-E-FMD-FS-V5R15

ObjectivesIn this course you will learn different ways to generate a solid mesh from eithersolid or surfacic parts

Participants' ProfileCatia V5 users

PrerequisitesGPS training

Content- Introduction to FEM Solid- Solid Meshing using Tetrahedron Filler- Solid Meshing using Octree Tetrahedron Mesher- Solid Meshing Using Sweep 3D- Solid Meshing using Mesh Transformation tools- Solid Meshing using Mesh Extrusion toolsn- Cutting Plane Analysis- Quality Analysis- Import/Export Meshes

ExercisesEx. 1: Engine Block Cylinder using Tetrahedron Filler (30min) / All sectorsEx. 2: Gear Meshing using Transformation (20min) / All sectorsEx. 3: Solid Mesh Generation using Extrusion (30min) / All sectorsEx. 4: Piston Meshing using Octree (15min) / All sectorsEx. 5: Solid Meshing Using Sweep 3D (15min) / All sectors


AnalysisSolutions FMS: FEM Surface

EDU-CAT-E-FMS-FCourse Code EDU-CAT-E-FMS-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMS-FI-V5R15 Foils: EDU-CAT-E-FMS-FF-V5R15 Exercises: EDU-CAT-E-FMS-FX-V5R15 Detailed Steps: EDU-CAT-E-FMS-FS-V5R15

ObjectivesIn this course, you will learn to quickly generate a finite element model forsurface parts.


PrerequisitesGenerative Part & Assembly Structural Analysis

Content- Introduction to FEM Surface- Advanced Surface Mesher- Surface Mesh- Octree Triangle Mesher- Beam Mesher- Mesh Operators - Mesh transformation- Mesh specifications exposition to Knowledge- Mesh Analysis tools- Mesh Update- Import/Export Mesh- Welding Meshing Method- Pre-processing Analysis Capabilities- Frequently Asked Questions

What is new in this releaseNew associative surface mesherMove Mesh NodesExtract coating elementsShrink ElementsNodes to Nodes connection meshNode interface mesh


ExercisesEx. 1: Meshing if cross member (60min) / All sectorsEx. 2: Floor Mesh (20min) / All sectorsEx. 3: Fuselage Door Static Analysis (30min) / AerospaceEx. 4: Spot welding Analysis (60min) / AutomotiveEx. 5: Seam welding analysis (15min) / All sectorsEx. 6: Surface welding Analysis (15min) / All sectorsEx. 7: Compatible seam welds (15min) / All sectorsEx. 8: spot welds with hemming (15min) / All sectorsEx. 9: Wing Structure Analysis (60min) / AerospaceEx. 10: Meshing of Parametric Conceptual Body (60min) / All sectorsEx. 11: Meshing of a Fuselage (30min) / All sectorsEx. 12: Fuselage Connections (30min) / All sectorsEx. 13: Pan Floor Mesh (30min) / All sectorsEx. 14: Octree Mesher on Block Cylinder (30min) / All sectorsEx. 15: Hybrid Mesh: 1D and 2D (45min) / All sectorsEx. 16: Extrude 1D Elements to 2D Mesh (20min) / All sectorsEx. 17: Mesh Parameters Exposition to knowledge 1 (15min) / All sectorsEx. 18: Mesh Parameters Exposition to knowledge 2 (15min) / All sectorsEx. 19: Mesh Parameters Exposition to knowledge 3 (15min) / All sectors


AnalysisSolutions GAS: Generative Assembly Structural Analysis

EDU-CAT-E-GAS-FCourse Code EDU-CAT-E-GAS-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GAS-FI-V5R15 Foils: EDU-CAT-E-GAS-FF-V5R15 Exercises: EDU-CAT-E-GAS-FX-V5R15 Detailed Steps: EDU-CAT-E-GAS-FS-V5R15

ObjectivesThis course covers tools for Structural Analysis on an assembly. Throughoutthis course, you will learn how to define connections between the differentparts of an assembly.Then,once the assembly is correctly defined, you will beable to perform a global assembly analysis using the GPS tools

Participants' ProfileCATIA Designers

PrerequisitesCATIA Basics Mechanical Design Generative Part Structural Analysis

Content- Introduction to GAS- Analysis Connections- GAS Connections- Analysis Assembly Management

ExercisesEx. 1: Face Face’ Connection Properties Recap Exercise (30min) / All sectorsEx. 2: Distant Connection Property Recap Exercise (60min) / All sectorsEx. 3: Analysis Assembly of Airplane Wing and Fuselage (45min) / AerospaceEx. 4: Static Analysis on an Assembly (1): Pre-Processing (40min) / All sectorsEx. 5: Static Analysis on an Assembly (Step2): Computation (5min) / All sectorsEx. 6: Static Analysis on an Assembly (Step3): Result Visualization (35min) /All sectorsEx. 7: Static Analysis on an Assembly (Step 4): Publishing Report (10min) / Allsectors


AnalysisSolutions GAS: Generative Assembly Structural Analysis

V5R15 UpdateEDU-CAT-E-GAS-UCourse Code EDU-CAT-E-GAS-UCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GAS-UI-V5R15 Foils: EDU-CAT-E-GAS-UF-V5R15

ObjectivesIn this course attendees will see the V5R14 main new tools and enhancementsfor Generative Assembly Structural Analysis

Participants' ProfileCATIA Analysis Users

PrerequisitesV5F,GPS,GAS

Content- Assembly of Analysis- Other Enhancements in GAS

ExercisesNone


AnalysisSolutions GDY: Generative Dynamic Response Analysis

EDU-CAT-E-GDY-FCourse Code EDU-CAT-E-GDY-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GDY-FI-V5R15 Foils: EDU-CAT-E-GDY-FF-V5R15 Exercises: EDU-CAT-E-GDY-FX-V5R15 Detailed Steps: EDU-CAT-E-GDY-FS-V5R15

ObjectivesThis course covers tools for dynamic response Analysis. Throughout thiscourse, you will see how to perform hamonic and transient analysis using thefinite elements method.

Participants' ProfileCATIA Designers Analysis Expert

PrerequisitesGenerative Part Structural Analysis

Content - Introduction to GDY - GDY Pre-Processing - Results Visualization

ExercisesEx. 1: Transient Dynamic Analysis : Computing a Static Analysis (20min) /AutomotiveEx. 2: Transient Dynamic Analysis : Computing the Frequency Analysis(10min) / AutomotiveEx. 3: Transient Dynamic Analysis : Computing the Transient Dynamic Case(30min) / Automotive


AnalysisSolutions GPE: Generative Part Structural Analysis

ExpertEDU-CAT-E-GPE-FCourse Code EDU-CAT-E-GPE-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GPE-FI-V5R15 Foils: EDU-CAT-E-GPE-FF-V5R15 Exercises: EDU-CAT-E-GPE-FX-V5R15 Detailed Steps: EDU-CAT-E-GPE-FS-V5R15

ObjectivesThis course covers advanced tools for Structural Analysis on a single part.Throughout this course, you will learn how to perform a frequency analysisusing the finite elements method.

Participants' ProfileDesigners, Mechanical engineers

PrerequisitesCatia FundamentalsGPS Fundamentals

Content- GPS pre-Processing- Computation - GPS Advanced Post-Processing Tools

ExercisesEx. 1: Pre-Processing’ Recap Exercise (20min) / All sectorsEx. 2: Results Visualization’ Recap Exercise (10min) / All sectorsEx. 3: Frequency Analysis on a Crank Shaft (1): Pre-Processing (15min) /AutomotiveEx. 4: Frequency Analysis on a Crank Shaft (Step2): Computation (5min) /AutomotiveEx. 5: Frequency Analysis on a Crank Shaft (Step3): Results (10min) /Automotive


AnalysisSolutions GPF: Generative Part Structural Analysis

FundamentalEDU-CAT-E-GPF-FCourse Code EDU-CAT-E-GPF-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GPF-FI-V5R15 Foils: EDU-CAT-E-GPF-FF-V5R15 Exercises: EDU-CAT-E-GPF-FX-V5R15 Detailed Steps: EDU-CAT-E-GPF-FS-V5R15

ObjectivesThis course covers the main tools for Structural Analysis on a single part.Throughout this course, you will learn how to perform a basic static analysisusing the finite elements method.


PrerequisitesCATIA Basics Mechanical Design

Content- Introduction to Finite Element Analysis- Introduction to GPS Analysis- GPS Pre-Processing- Computation- GPS Post-Processing- Managing Analysis

Notes

ExercisesEx. 1: Pre-Processing’ Recap Exercise (10min) / All sectorsEx. 2: ‘Computation’ Recap Exercise (5min) / All sectorsEx. 3: ‘Results Visualization’ Recap Exercise (10min) / All sectorsEx. 4: ‘Results Management’ Recap Exercise (10min) / All sectorsEx. 5: ‘Refinement’ Recap Exercise (10min) / All sectorsEx. 6: Mesh Refinement with Precision : Recap Exercise (60min) / All sectorsEx. 7: Static Analysis on a Hanger (1): Pre-Processing (15min) / All sectorsEx. 8: Static Analysis on a Hanger (Step2): Computation (5min) / All sectorsEx. 9: Static Analysis on a Hanger (Step3): Result Visualization (30min) / Allsectors


AnalysisSolutions GPS: Generative Part Structural Analysis

V5R15 UpdateEDU-CAT-E-GPS-UCourse Code EDU-CAT-E-GPS-UCATIA V5R15Brand & Release CATIA V5R150.1 dayDuration 0.1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GPS-UI-V5R15 Foils: EDU-CAT-E-GPS-UF-V5R15

ObjectivesIn this course attendees will see the V5R14 main new tools and enhancementsfor Generative Part Structural Analysis workbench


PrerequisitesGenerative Part Structural Analysis

Content- Measure in Images

ExercisesNone


AnalysisSolutions TAA: Tolerance Analysis of Deformable

AssemblyEDU-CAT-E-TAA-FCourse Code EDU-CAT-E-TAA-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TAA-FI-V5R15 Foils: EDU-CAT-E-TAA-FF-V5R15 Exercises: EDU-CAT-E-TAA-FX-V5R15 Additional Information: EDU-CAT-E-TAA-FO-V5R15

ObjectivesIn this course, you will learn about the Tolerance Analysis of DeformableAssembly workbench and more precisely about the Process Product Resourceconcept and the main functionalities.

Participants' ProfileExperienced CATIA V5 users

PrerequisitesGenerative Shape Design (GSD)Generative Part Structural Analysis (GPS)

Content- Plates assembly Interactive Tolerance analysis- Tolerance analysis from a text file- Tolerancing and Analysis geometric variations- Sensitivity Tolerance analysis from a text file- Complete Plates assembly TAA text file creation- Interactive Tolerance analysis : Application

What is new in this releaseFunctionality UpdateExercices update

ExercisesEx. 1: Plates assembly Interactive Tolerance analysis (120min) / All sectorsEx. 2: Tolerance analysis from a text file (90min) / All sectorsEx. 3: Tolerancing and Analysis geometric variations (100min) / All sectorsEx. 4: Sensitivity Tolerance analysis from a text file (100min) / All sectorsEx. 5: Complete Plates Assembly text file creation (100min) / All sectorsEx. 6: Interactive Tolerance analysis : Application (480min) / Aerospace,Automotive, Shipbuilding



Equipment & Systems Engineering Solutions


Equipment & SystemsEngineeringSolutions

CBD: Circuit Board Design

EDU-CAT-E-CBD-FCourse Code EDU-CAT-E-CBD-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesFoils: EDU-CAT-E-CBD-FF-V5R15 Instructor Foils: EDU-CAT-E-CBD-FI-V5R15 Detailed Steps: EDU-CAT-E-CBD-FS-V5R15 Exercises: EDU-CAT-E-CBD-FX-V5R15

ObjectivesAt the end of this course, participants will be able to:- Create Printed Circuit Boards (PCB) in a context of Assemblies,- Export and import to/from an ECAD tool using the IDF interface.

Participants' ProfileElectrical designers knowing how to work with CATIA V5 Parts and Assemblies

PrerequisitesCOM-F: Getting Started with CATIA V5PDG-F: Part Design

Content- Introduction to Circuit Board Design- Creating the PCB geometry with mounting holes- Constraint areas and components- Export and Import using the IDF Interface - Creating a catalog of electrical components

ExercisesEx. 1: Transformer (45min) / Electronics & ElectricalEx. 2: Connector Box (40min) / Electronics & ElectricalEx. 3: Camera (30min) / Electronics & Electrical



EHF: Electical Harness Flattening

EDU-CAT-E-EHF-FCourse Code EDU-CAT-E-EHF-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EHF-FI-V5R15 Foils: EDU-CAT-E-EHF-FF-V5R15 Exercises: EDU-CAT-E-EHF-FX-V5R15

ObjectivesIn this course you will learn how to flatten an electrical or geometrical harnessintegrated within the DMU and how to modify the bundle segments of theharness to fit your drawing in order to build the harness documentation

Participants' ProfileElectrical V5 users

PrerequisitesPRO-F: CATIA Tools for Proficient UsersEHI-F: Electrical Harness InstallationELB-F: Electrical Librarian

ContentIntroduction to Harness FlatteningHarness Flattening parametersExtracting dataHarness flattening modificationsSynchronizeLinks visualizationReportsDrawingCatalog text template creationGraphic Replacement

What is new in this releaseUp to date course

ExercisesEx. 1: Harness Documentation / Electronics & ElectricalEx. 2: Harness Flattening / Electronics & ElectricalEx. 3: Harness Documentation (2) / Electronics & ElectricalEx. 4: Harness Flattening (2) / Electronics & Electrical



EHI: Electrical Harness Installation

EDU-CAT-E-EHI-FCourse Code EDU-CAT-E-EHI-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EHI-FI-V5R15 Foils: EDU-CAT-E-EHI-FF-V5R15 Exercises: EDU-CAT-E-EHI-FX-V5R15

ObjectivesIn this course, you will learn how to build a harness integrated within theDMU:for 3D electrical space reservation on harness detailed design.

Participants' ProfileNew CATIA V5 Electrical users

PrerequisitesCATIA V5 Part DesignCATIA V5 Assembly Design

ContentIntroduction to Electrical Harness InstallationElectrical Harness SettingsGeometric Bundle definitionPosition Electrical DevicesBundle segment DefinitionManaging a Branch PointDelete BranchSplit a Bundle segmentTransfer BranchesInstantiate a protectionAdjusts DiameterLinks managementLocal slackSupport ManagementMeasure geometrical bundle inertiaV4/V5 Migration

What is new in this releaseEnhance pedagogy of the trainingNew exercises trainingV5R15 up to date

ExercisesEx. 1: Bundle Segment Definition (15min) / All sectorsEx. 2: Position supports (10min) / All sectorsEx. 3: Link a bundle segment (10min) / All sectorsEx. 4: Add a Support to a Bundle Segment (10min) / All sectorsEx. 5: Manage the Local Slack to the Bundle Segment (10min) / All sectorsEx. 6: Manage the bundle segment section (20min) / All sectorsEx. 7: Transfer Branches (15min) / All sectorsEx. 8: Instantiate a Protection (15min) / All sectorsEx. 9: Adjusts Diameter (15min) / All sectorsEx. 10: Define a Bundle Segment (15min) / All sectorsEx. 11: Define a Bundle Segment (45min) / All sectorsEx. 12: Electrical Harness installation (90min) / All sectorsEx. 13: Harness Design (45min) / All sectorsEx. 14: Geometrical bundle inertia (15min) / All sectors



ELB: Electrical Librarian

EDU-CAT-E-ELB-FCourse Code EDU-CAT-E-ELB-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ELB-FI-V5R15 Foils: EDU-CAT-E-ELB-FF-V5R15 Exercises: EDU-CAT-E-ELB-FX-V5R15

ObjectivesAt the end of this course, participants will be able to:- Define standard electrical components,- Manage electrical catalogs,- Place electrical components in the digital mockup.

Participants' ProfileNew CATIA V5 Electrical users

PrerequisitesCATIA V5 Part Design practiceCATIA V5 Assembly Design

Content- Introduction to Electrical Librarian- Electrical Components Definition- Electrical Librarian Catalog Management- Electrical Assemblies- Wires Management- Importing electrical external data for 3D implementation

What is new in this releaseEnhance pedagogy of the trainingNew exercises trainingV5R15 up to date

ExercisesEx. 1: Creating a catalog (10min) / All sectorsEx. 2: Defining a set of electrical components (90min) / All sectorsEx. 3: Store components in a catalog (15min) / All sectorsEx. 4: Define an assembly with the components from the catalog (15min) / AllsectorsEx. 5: Create a protection and store it into a catalog (15min) / All sectorsEx. 6: Create a wire and store it into a catalog (15min) / All sectorsEx. 7: Create an adaptative support and use the Smart Placement icon (60min)/ All sectorsEx. 8: External Data (30min) / All sectorsEx. 9: Car Door (45min) / All sectors



EWR: Electrical Wire Routing

EDU-CAT-E-EWR-FCourse Code EDU-CAT-E-EWR-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EWR-FI-V5R15 Foils: EDU-CAT-E-EWR-FF-V5R15 Exercises: EDU-CAT-E-EWR-FX-V5R15

ObjectivesAt the end of this course, participants will be able to:- Route wires in a harness.- Route signals in space reservation system- Use knowledgeware for segregation rules

Participants' ProfileNew V5 CATIA electrical users

PrerequisitesCATIA V5 Part DesignCATIA V5 Assembly Design

ContentIntroduction to Electrical Wire RoutingImport External DataWires Management

ExercisesEx. 1: External Data Exchange (60min) / All sectorsEx. 2: External Data (60min) / All sectorsEx. 3: External Data Exchange (60min) / All sectors



TUB: Tubing Design

EDU-CAT-E-TUB-FCourse Code EDU-CAT-E-TUB-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUB-FI-V5R15 Foils: EDU-CAT-E-TUB-FF-V5R15 Exercises: EDU-CAT-E-TUB-FX-V5R15 Detailed Steps: EDU-CAT-E-TUB-FS-V5R15

ObjectivesIn this course you will learn how the CATIA Tubing Design product is used toquickly and efficiently create an intelligent tubing layout.


PrerequisitesCATIA V5 Fundamentals

Content- Introduction to Tubing Design - General Philosophy- Accessing the Workbench- User Interface- Tubing Design Fundamentals- Understanding the General Process- Selecting a Project and a Discipline- Managing Tubing Line ID’s- Routing a Tubing Run- Routing a Flexible Tubing- Routing a Tubing Bundle- Modifying a Tubing Run- Managing Spools- Placing and Modifying Parts on a Tubing Run- Managing Flow Direction- Object Navigator- Graphic Representation - Schematic Driven - Saving a Tubing Document - Generating Reports- To sum up

ExercisesEx. 1: Creating, Modifying and placing parts on a run (45min) / All sectorsEx. 2: Flexible and Bundle of Flexibles (20min) / All sectorsEx. 3: Global Exercise (60min) / All sectorsEx. 4: Generating Production Documents (15min) / All sectorsEx. 5: Schematics-Driven Design (10min) / All sectors



TUD: Tubing Diagrams

EDU-CAT-E-TUD-FCourse Code EDU-CAT-E-TUD-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUD-FI-V5R15 Foils: EDU-CAT-E-TUD-FF-V5R15 Exercises: EDU-CAT-E-TUD-FX-V5R15 Detailed Steps: EDU-CAT-E-TUD-FS-V5R15

ObjectivesThis course illustrates how the Tubing Diagram product could be used toquickly and efficiently create a schematic diagram.

Participants' ProfileExperienced CATIA V5 Users


Content- Starting a Tubing Diagram - Diagram Creation- Zone Creation and Management - Diagram Modification/Annotation/Reports- Design Checks- Network Analysis- Object Navigator- to sum up

ExercisesEx. 1: Tubing Diagrams Fundamental (Master Exercise) (60min) / All sectors



TUS: Tubing Catalogs (2D Diagrams & 3DDesign)

EDU-CAT-E-TUS-ACourse Code EDU-CAT-E-TUS-ACATIA V5R15Brand & Release CATIA V5R154 daysDuration 4 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUS-AI-V5R15 Foils: EDU-CAT-E-TUS-AF-V5R15 Exercises: EDU-CAT-E-TUS-AX-V5R15 Detailed Steps: EDU-CAT-E-TUS-AS-V5R15

ObjectivesThis courseware is designed to teach Tubing specialists and administratorshow to define 2D (schematic diagrams) & 3D Tubing catalogs andspecifications.

Participants' Profile2D & 3D Catalog designers and administrators for Equipment & Systems andwho are experienced CATIA V5 users.

PrerequisitesTUD: Tubing Diagrams Fundamentals (EDU-CAT-E-TUD-F - V5R15)TUB: Tubing Design Fundamentals (EDU-CAT-E-TUB-F - V5R15)or

Generic Routing (EDU-CAT-E-ES2-F - V5R15)

ContentDefinitions General Philosophy – Feature Concept General Philosophy – Catalogs General Philosophy – Rules and Attributes Understanding the General Process Global Customization ProcessTubing Workbench Customization Project Resource Management Feature Dictionary 2D Diagrams Catalogs Creation Standards Catalog Design Rules Catalog Building Tubing Parts Creating a New Tubing Part Building a Bendable Tube Creating a Tubing Parts Catalog (Master) Placing Parts From the Tubing Parts Catalog Setting up Specifications Catalog Placing Parts From the Specifications CatalogCreating a Report Generating a Report From a Macro – First Solution Defining and Generating a customized Report – Second SolutionTo Sum up

What is new in this releaseNew courseware covering former 2D Tubing Diagrams Advanced and 3DTubing Design Advanced.


NotesThis courseware is new in V5R15.4 days are necessary if people are starting with tubing catalogs. If people havealready seen other catalogs (such as Piping or HVAC).

ExercisesEx. 1: Creating a Tubing Catalog (360min) / All sectorsEx. 2: Creating a 2D Diagram Catalog (140min) / All sectors



Infrastructure Solutions


InfrastructureSolutions ADM: V5 Administration

EDU-CAT-E-ADM-FCourse Code EDU-CAT-E-ADM-FCATIA V5R15Brand & Release CATIA V5R153 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ADM-FI-V5R15 Foils: EDU-CAT-E-ADM-FF-V5R15 Exercises: EDU-CAT-E-ADM-FX-V5R15

ObjectivesAt the end of this course, administrators will know how to install, customize andmaintain CATIA V5.They will study many issues about CATIA infrastructure, administration anddata management.

Participants' ProfileThis class is for Unix & Windows NT System Administrators andCATIA/ENOVIA key application & support engineers.

PrerequisitesUnix AdministrationNT Administration

Content- Installing CATIA V5 on NT and on Unix with documentation- Looking at Licensing system and configurations- License management on NT and Unix- CATIA V5 environments and related variables- Customized installations and users settings- Administrating settings with VB macros - Lock and set default settings by administrator/root- Organize CATIA data with DLNames- Customizing general and drafting standards- Upgrading from CATIA V5 service packs approach- Procedures for automatic installation checking on NT and Unix- Distributing CATIA on NT and Unix clients - A view of various batch tools- Reviewing Data and links management aspects - Over viewing of UNIX/Windows and V4/V5 interoperability

What is new in this release- statistics- batches improvments

ExercisesEx. 1: Installing CATIA V5 on NT (30min) / All sectorsEx. 2: Checking, configuring licenses (10min) / All sectorsEx. 3: Customizing an environment (20min) / All sectorsEx. 4: Settings (60min) / All sectorsEx. 5: Customizing standards (15min) / All sectorsEx. 6: Installing a service pack, Distributing CATIA V5 to client from server onNT, checking the installation (60min) / All sectorsEx. 7: Practicing with tools (30min) / All sectorsEx. 8: Understanding Document environment anf links (60min) / All sectorsEx. 9: Interoperability cases (15min) / All sectors


InfrastructureSolutions PRO: CATIA Tools For Proficient Users

EDU-CAT-E-PRO-FCourse Code EDU-CAT-E-PRO-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-PRO-FI-V5R15 Foils: EDU-CAT-E-PRO-FF-V5R15

ObjectivesIn this course you will learn how to use tools dedicated to CATIA V5 ProjectMaster such as the Catalog edition, Power-copy management and UserDefined Feature management.

Participants' ProfileAdvanced Users

PrerequisitesCATIA BASICS, Part Design

Content- Creating and Using Powercopies- Creating Catalogs of Components- From CATIA V4 to V5 Basics

ExercisesEx. 1: Creating a PowerCopy (20min) / All sectorsEx. 2: Instantiating a PowerCopy (10min) / All sectorsEx. 3: Creating a Catalog from a CATDrawing file (15min) / All sectorsEx. 4: Adding a Chapter to a Catalog (10min) / All sectorsEx. 5: Adding a Family (10min) / All sectorsEx. 6: Creating a Keyword in a Catalog (10min) / All sectorsEx. 7: Adding a Component (10min) / All sectorsEx. 8: Copying a CATIA V4 Solid into CATIA V5 (10min) / All sectors


InfrastructureSolutions V4I: V4 Integration

EDU-CAT-E-V4I-FCourse Code EDU-CAT-E-V4I-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V4I-FI-V5R15 Foils: EDU-CAT-E-V4I-FF-V5R15 Exercises: EDU-CAT-E-V4I-FX-V5R15 Detailed Steps: EDU-CAT-E-V4I-FS-V5R15 Demonstration: EDU-CAT-E-V4I-FD-V5R15

ObjectivesAt the end of this course, participants will be able to:- Use CATIA V4 data in CATIA V5- Transfer a CATIA V4 solid into a CATIA V5 CATPart- Manage the links between CATIA V4 and CATIA V5 documents


PrerequisitesBasic knowledge of CATIA V5 Mechanical Design Solutions

Content- Introduction to V4 Integration- Creating a CATProduct using V4 data- Assembly of V4 data in a V5 CATProduct- Transferring V4 data into V5 CATPart- Design in context- Drawing of a V4/V5 document in V5- Migration of 2D Draw elements and Views- CATIA V5 DMU solutions and V4 data- Links between V4 data and V5 documents

What is new in this releasedifferences between Windows and UNIX commands.

NotesThe document EDU-CAT-E-V4I-FI-V5R15 (instructor foils) is exactly the samedocument as EDU-CAT-E-V4I-FF-V5R15 (student foils)

ExercisesEx. 1: Recap Exercise 1 : open and check the V4 geometry (20min) / AllsectorsEx. 2: Recap Exercise 2 : Solid translation (15min) / All sectorsEx. 3: Recap Exercise 3 : manipulations in a CATProduct (20min) / All sectorsEx. 4: Welding Gun : Creating a CATProduct with V4 data (10min) / All sectorsEx. 5: Welding Gun : Assembly of V4 data in a V5 CATProduct (15min) / AllsectorsEx. 6: Welding Gun : Copy/Pasting a V4 solid in a V5 CATPart (20min) / AllsectorsEx. 7: Welding Gun : Design in context (20min) / All sectorsEx. 8: Welding Gun : Generative drafting (20min) / All sectorsEx. 9: Welding Gun : DMU Space Analysis (20min) / All sectorsEx. 10: Welding Gun : V4 Modification and Update in V5 (20min) / All sectors


InfrastructureSolutions V4I: V4/V5 Advanced Interoperability

EDU-CAT-E-V4I-ACourse Code EDU-CAT-E-V4I-ACATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V4I-AI-V5R15 Foils: EDU-CAT-E-V4I-AF-V5R15 Exercises: EDU-CAT-E-V4I-AX-V5R15

ObjectivesIn this course, you will learn advanced interoperability concepts about themigration of CATIA V4 geometric/application data to CATIA V5. You will alsolearn how V5 data can be saved in CATIA V4 formats or used directly in CATIAV4.

Participants' ProfileExperienced CATIA V4/V5 users

PrerequisitesBasic knowledge of CATIA V5 Mechanical Design Solutions

Content- From V4 to V5 - Transfer of V4 geometric data to V5 - Transfer of V4 application data to V5- From V5 to V4 - Using V5 data in V4 - Saving V5 data in V4 formats

What is new in this releaseThe UUID (Universally Unique Identifier) in order to give information about theresults of migration in batch.LCA/VPM Databases support in the V4/V5 datalifecycle batch

NotesRequired SoftwaresCATIA V5 (P2 version)V5R14CATIA V4424 R1Not absolutely necessary. Recommanded, 1 Unixmachine only with 1 CATIA V5 license available. Must be accessible from NTmachines (NFS Hummingbird or others) and declared as an http server.

the document EDU-CAT-E-V4I-AI-V5R15 (instructor foils) is exactly the sameas the document EDU-CAT-E-V4I-AF-V5R15 (student foils)

ExercisesEx. 1: Smart/Unsmart Solid (15min) / All sectorsEx. 2: Error during update (15min) / All sectorsEx. 3: Migration of kinematics data (25min) / All sectorsEx. 4: Sheet Metal Design (10min) / All sectors


InfrastructureSolutions VBA: CATIA V5 Automation

EDU-CAT-E-VBA-FCourse Code EDU-CAT-E-VBA-FCATIA V5R15Brand & Release CATIA V5R153 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-VBA-FI-V5R15 Foils: EDU-CAT-E-VBA-FF-V5R15 Exercises: EDU-CAT-E-VBA-FX-V5R15

ObjectivesAt the end of this course, participants will have a good understanding of thedifferent ways to automate tasks related to CATIA V5: CATIA Macros andVisual Basic Programming.

Participants' ProfileCATIA V5 Applications developers; bench markers

PrerequisitesCATIA V5 Fundamentals.Visual Basic Editor on PC NTMinimum knowledge or exposure to Microsoft Visual Basic (cf. book ref.Microsoft Visual Basic 6.0 Learning Edition)JavaScript is a plus

Content- CATIA V5 OLE Automation, Journaling & Scripting Architecture- Exported objects of CATIA V5- Designing panels for Macros- Graphic selection of objects- Settings - V5 Administration - Communication with another Automation server.

ExercisesEx. 1: Cylinders (Master Exercise) (10min) / All sectorsEx. 2: Modifying the viewpoint of an existing document (30min) / All sectorsEx. 3: Creating 2D sketch with constraints (15min) / All sectorsEx. 4: Creating part design features (30min) / All sectorsEx. 5: Creating 3D wireframes and 3D surfaces (30min) / All sectorsEx. 6: Titanic (30min) / All sectorsEx. 7: Drafting the bolt (30min) / All sectorsEx. 8: Test Selections (30min) / All sectorsEx. 9: Select Element (30min) / All sectorsEx. 10: Get Point (30min) / All sectorsEx. 11: Settings - Applying local changes (20min) / All sectors



Mechanical Design Solutions


Mechanical DesignSolutions ASL: Aerospace Sheet Metal Design

EDU-CAT-E-ASL-FCourse Code EDU-CAT-E-ASL-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ASL-FI-V5R15 Foils: EDU-CAT-E-ASL-FF-V5R15 Exercises: EDU-CAT-E-ASL-FX-V5R15 Detailed Steps: EDU-CAT-E-ASL-FS-V5R15

ObjectivesIn this course, you will learn how to generate sheet metal parts for aerospace

Participants' ProfileAerospace Airframe Designer

PrerequisitesPart Design, Assembly Design, Wireframe and Surface Design

Content- Introduction to Aerospace Sheet Metal Design- ASL Parameters- Creating the Web- Creating a Surfacic Flange- Creating a Joggle- Creating Flanges- Creating a Corner Relief - Creating a Cut Out- Creating Stamps - Flanged Hole - Bead - Circular Stamp - Surface Stamp - Flanged Cutout - Stiffening Rib - Curve Stamp - User Stamp- Creating a Hole- Points or Curves Mapping- Creating Corners or Chamfers- Applying a Pattern- Modifying a Feature- Generating Folded and Flattened Parts- Drawing Generation

What is new in this releaseNo V5R15 Functional Enhancement.User Interface change about Surfacic Flange Support (panel and preview)

ExercisesEx. 1: Fighter Airframe (50min) / All sectorsEx. 2: Aero Structure (30min) / All sectorsEx. 3: Bracket (15min) / All sectorsEx. 4: Fighter Web Structure (20min) / All sectorsEx. 5: Rib (20min) / All sectors


Mechanical DesignSolutions ASM: CATIA Product Design Expert

EDU-CAT-E-ASM-ACourse Code EDU-CAT-E-ASM-ACATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-ASM-AI-V5R15 Foils: EDU-CAT-E-ASM-AF-V5R15 Exercises: EDU-CAT-E-ASM-AX-V5R15 Detailed Steps: EDU-CAT-E-ASM-AS-V5R15 Detailed Steps: EDU-CAT-E-ASM-AS-V5R15

ObjectivesUpon completion of this course, you will be be able to design assemblies usingcollaborative engineering practices, optimize performance for large assembliesand analyze assemblies.

Participants' ProfileAdvanced Users

PrerequisitesCATIA Product Design, CATIA Part Design

Content- Managing a Product Structure- Designing & Managing Contextual Parts- Creating and Using Published Geometry- Flexible Sub-Assembly- Working with Large Assemblies- Analyzing Assemblies to Prepare drawing

ExercisesEx. 1: Assembly Design Settings (30min) / All sectorsEx. 2: Connector Assembly - Assembling Components (15min) / All sectorsEx. 3: Connector Assembly - Positioning Components (20min) / All sectorsEx. 4: Connector Assembly - Analyzing the Assembly (15min) / All sectorsEx. 5: Connector Assembly - Fixing the clash (30min) / All sectorsEx. 6: Connector Assembly - Adding screws (10min) / All sectorsEx. 7: Vice Assembly - Creating the Structure (15min) / All sectorsEx. 8: Vice Assembly - Positioning Components (20min) / All sectorsEx. 9: Vice Assembly - Editing parts (20min) / All sectorsEx. 10: Vice Assembly - Inserting Fitting Components (15min) / All sectorsEx. 11: Flexible Assemblies : Assembling Components (3min) / All sectorsEx. 12: Flexible Assemblies : Constrain Clamp Assembly (15min) / All sectorsEx. 13: Flexible Assemblies : Change configuration (7min) / All sectors


Mechanical DesignSolutions CCV: Core & Cavity Design

EDU-CAT-E-CCV-FCourse Code EDU-CAT-E-CCV-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-CCV-FI-V5R15 Foils: EDU-CAT-E-CCV-FF-V5R15 Exercises: EDU-CAT-E-CCV-FX-V5R15 Detailed Steps: EDU-CAT-E-CCV-FS-V5R15

ObjectivesIn this course you will learn how to use workbench Core & Cavity Design tocreate the Core and Cavity sides of a part, including sliders and loose cores,required for the design of a plastic injection mold.

Participants' ProfileNew Core & Cavity Design users

PrerequisitesV5F-F: CATIA V5 Fundamentals

Content- Import the Part to mold- Define the Main Pulling Direction- Define a Slider/Lifter Pulling Direction- Work on Mold Areas : Transfer, Aggregate, Split, Explode, Bounding Box- Define Parting Surface- Comparing two parts

ExercisesEx. 1: Pan Handle (60min) / All sectorsEx. 2: Support (30min) / All sectors


Mechanical DesignSolutions DDR: CATIA Detail Drafting

EDU-CAT-E-DDR-FCourse Code EDU-CAT-E-DDR-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-DDR-FI-V5R15 Foils: EDU-CAT-E-DDR-FF-V5R15 Exercises: EDU-CAT-E-DDR-FX-V5R15 Detailed Steps: EDU-CAT-E-DDR-FS-V5R15

ObjectivesUpon completion the student will be able to create and modify assembly anddetailed drawings using various view types, dimensions, notes, andannotations. They will also be able to create, analyze, and modify the drawingusing the links to products or parts. �

Participants' ProfileCATIA V5 Mechanical Users

PrerequisitesPart Design, Assembly Design

Content- Introduction to Drafting- Getting Started- Drawing Views- Editing View Properties and Layouts- Dimensioning a Drawing- Adding Annotation- Finalizing the Drawing- Customizing the Drafting Workbench- Master Exercise 1- Master Exercise 2

What is new in this releaseThe master exercise 2 has been replaced.

ExercisesEx. 1: Getting Started: Recap Exercises (45min) / All sectorsEx. 2: Adding Drawing Views (45min) / All sectorsEx. 3: Editing View Properties and Layouts (45min) / All sectorsEx. 4: Dimensioning a Drawing (45min) / All sectorsEx. 5: Adding Annotations (30min) / All sectorsEx. 6: Car Jack Support (30min) / All sectorsEx. 7: Master Exercise 1 (60min) / All sectorsEx. 8: Master Exercise 2 (45min) / Fabrication & Assemblies Consumer Goods


Mechanical DesignSolutions DRA: Advanced Drafting

EDU-CAT-E-DRA-ACourse Code EDU-CAT-E-DRA-ACATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-DRA-AI-V5R15 Foils: EDU-CAT-E-DRA-AF-V5R15 Exercises: EDU-CAT-E-DRA-AX-V5R15

ObjectivesIn this class, participants will Benefit from hints and tips on-Interactive drafting-Dimension generation from 3D definitions of parts -Learn how to define standards and re-use existing start-up drawings-Build frames, title & revision blocks from table values with VBScript supportAnd in general set and manage all dimension and annotation standardscontained in the standard file according to their company or projects needs.

Participants' ProfileExperienced drafters

PrerequisitesV5F: CATIA V5 Fundamentals (EDU-CAT-E-V5F-F - V5R14)CATIA V5 VB Automation (C514-INF-E-A6 - V5R14)

ContentDuring this 2-day session you will see •Detail review of CATIA drafting tools available in: •DR1: CATIA Drafting 1 Configuration•DP2: CATIA Drawing Production 2 Configuration•Defining Company Drawing Standards (production set)•Setting drawing formats, symbols, start up drawings patterns according to aCompany or project standards•Setting and controlling Standard files and Set As Default Applications•Reusing an existing start-up drawing•For a generative drawing:•Advanced filtering techniques (multi-selection of nodes and attributes ofviews)•Auto-dimensioning and balloon creation•Defining drawing formats (frame) and title block information (with and withoutVB Scripts)•Integrating table values or revision information•Customizing with VB Script•Creating tolerance tables (automation) and managing ditto •Recommended Methodologies for ID1,•Hints and Tips, annotation and dress up tools (dimensions standards, textstandards, FD&T standards, center line with and without reference, etc…)

What is new in this releaseNew Course

ExercisesEx. 1: The Plate (45min) / All sectorsEx. 2: The Pivot (45min) / All sectorsEx. 3: Generating Dimensions (25min) / All sectorsEx. 4: Using filtering techniques (25min) / All sectorsEx. 5: Geometry & Free Text in VB Script (15min) / All sectorsEx. 6: Fill in Title Block (20min) / All sectors


Mechanical DesignSolutions FMP: Functional Molded Part

EDU-CAT-E-FMP-FCourse Code EDU-CAT-E-FMP-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMP-FI-V5R15 Foils: EDU-CAT-E-FMP-FF-V5R15 Exercises: EDU-CAT-E-FMP-FX-V5R15

ObjectivesMake quick 3D molded parts digital models in CATIA thanks to the new easyteaching and learning workbench \\\\\\\"Functional Molded Part\\\\\\\".Extract associatively in solid Cavity and core of molds (P2)

Participants' ProfileMolded Part Designers or engineers (Plastic, Cast)Application Engineer

PrerequisitesPDG-F: Part Design


ContentIntroduction What is a molded part Design with Functional Molded part Access the workbench User interface and toolbarsShape Features and Mold Design Properties Introduction to Shape Features : Shellable Feature example Definition of Shape Features : Shellable Feature example Kinds of Shape Features Why / When do we need these kinds of Features? Shellable Feature description Mold Design properties Cavity Feature Added Feature Protected Feature Internal Feature Core FeatureFunctional Features Introduction to Functional Features : Rib example Definition of Functional Features : Rib example Kinds of Functional Features Rib Feature Description Cutout Pocket Boss Rest Grill Reinforcement Push Pull FittingFeature Modifier Introduction to Feature Modifier Cut Feature Remove Feature Intersect FeatureDress up Features Kind of Dress Up features Why / When do we need tho use them ?Functional Extration Design Process To sum Up

What is new in this release- Improved introduction- New features: Functional extraction toolbar (P2), - User Interface enhancements

ExercisesEx. 1: Locking cover (45min) / All sectorsEx. 2: Belt Housing (60min) / All sectorsEx. 3: Electrical box housing (60min) / All sectorsEx. 4: Notepad (30min) / All sectorsEx. 5: Functional mold extraction Electrical box housing (25min) / All sectors


Mechanical DesignSolutions FR1: Part Design Feature Recognition

EDU-CAT-E-FR1-FCourse Code EDU-CAT-E-FR1-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FR1-FI-V5R15 Foils: EDU-CAT-E-FR1-FF-V5R15 Exercises: EDU-CAT-E-FR1-FX-V5R15

ObjectivesThis course aims at introducing the Feature Recognition capability, which ispart of the Part Design workbench. The exercise shows how to perform aFeature Recognition operation.

Participants' ProfileDesigners

PrerequisitesPart Design

ContentWhat is “Feature Recognition” ?Accessing the Workbench Part Analysis ToolHow to perform a FR ?Feature Recognition PanelExamplesTips

What is new in this releasePart Analysis Tool

Notes"Part Design Feature Recognition" tool is also useful in V4-to-V5 migrationcontext.From isolated solid imported from V4, we can create a V5 specifivationsstructure, thanks to "Feature Recognition", and then rework the geometry.

ExercisesEx. 1: Creating V5 geometry from an isolated solid (30min) / All sectors


Mechanical DesignSolutions FTD: 3D Functional Tolerancing & Annotation

EDU-CAT-E-FTD-FCourse Code EDU-CAT-E-FTD-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FTD-FI-V5R15 Foils: EDU-CAT-E-FTD-FF-V5R15 Exercises: EDU-CAT-E-FTD-FX-V5R15

Objectives"The computer aided Tolerancing is an important topic in the field ofmechanical designing and production. Even if the means of production havebeen greatly improved and if the variability of production systems is better andbetter controlled, the dispersions of the characteristics manufactured remain.They directly influence the assembly and the quality of the way mechanismswork \\\\\\\"(CIRP 24/25 April 2001). In this course you will learn how to defineFunctional Tolerances and Annotation on geometric parts designed with CATIAV5 3D Wireframe or Solid geometry. This product is a main milestone in the 3dFunctional Tolerancing Process.This course material is used in the 3d Functional Tolerancing Process class.

Participants' ProfileCATIA V5 Users having a good experience in Mechanical Design.

PrerequisitesCATIA V5 Fundamentals or knowledge equivalent to CATIA User Companionfor Mechanical Design product.

ContentParticipants will see the benefits of using CATIA V5 FTA product in anindustrial environment & through a presentation of the fundamentals andexercises. The second day is more dedicated to advanced functionnalities tosupport different partner"projects.

- Day 1: - Lessons: - Introduction to FT&A worbench & Fundamentals of FT&A - Managing FT&A Annotations - Exercices: - Create & Manage 3d Annotations - Create drawing views and graphic manage of annotations - Create assembly annotations and assembly 2D views- Day 2: - Lessons: - Geometry Management - Advanced Functions - Exercices: - Geometrical modification and 3D annotations update - Advanced Functional Tolerancing and Annotations functions - Knowledge and 3D Annotations

What is new in this releaseThe course & exercices have been improved by taking account of customersfeedbacks and FTD added values V5R15 & V5R14

NotesBefore offering this training to customer, it's important to understand thepossible motivations and the targeted project. This information is mandatorybefore providing this support & engineering services.


ExercisesEx. 1: Create & Manage 3d Annotations (65min) / All sectorsEx. 2: Create drawing views and graphic manage of annotations (80min) / AllsectorsEx. 3: Create assembly annotations and assembly 2D views (25min) / AllsectorsEx. 4: Geometrical modification and 3D annotations update (85min) / AllsectorsEx. 5: Advanced Functional Tolerancing and Annotations functions (55min) / AllsectorsEx. 6: Knowledge and 3D Annotations (45min) / All sectors


Mechanical DesignSolutions GS1: CATIA Surface Design

EDU-CAT-E-GS1-FCourse Code EDU-CAT-E-GS1-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GS1-FI-V5R15 Foils: EDU-CAT-E-GS1-FF-V5R15 Exercises: EDU-CAT-E-GS1-FX-V5R15 Detailed Steps: EDU-CAT-E-GS1-FS-V5R15

ObjectivesUpon completion of the training, you will be able to create or modify parts madeof parametric mechanical surfaces, by practicing on curves and surfaces. Youwill also create solids from surfaces.

Participants' ProfileMechanical Designers

PrerequisitesV5 Fundamentals,Getting Started with CATIA V5 Sketcher

Content- Introduction to Surface Design- Creating Wireframe Geometry- Shape Design Common Tools- Creating Basic Surfaces- Performing Operations on the Geometry- Completing the Geometry in Part Design- Modifying the Geometry- Using Tools

ExercisesEx. 1: Creating Wireframe Geometry : Button (10min) / All sectorsEx. 2: Creating Wireframe Geometry : Mouse (15min) / All sectorsEx. 3: Creating Basic Surfaces : Button (5min) / All sectorsEx. 4: Creating Basic Surfaces : Mouse (15min) / All sectorsEx. 5: Operations on Geometry : Mouse (10min) / All sectorsEx. 6: Performing Operations on Geometry : Torch (30min) / All sectorsEx. 7: Completing the Solid in Part Design : Button (10min) / All sectorsEx. 8: Completing the Solid in Part Design : Mouse (30min) / All sectorsEx. 9: Modifying the Geometry : Button (10min) / All sectorsEx. 10: Modifying the Geometry : Mouse (10min) / All sectorsEx. 11: Using Tools : Surface Check Exercise (10min) / All sectorsEx. 12: Mobile Phone (1): Creating Wireframe Geometry (15min) / Electronics& ElectricalEx. 13: Mobile Phone (2): Creating Basic Surfaces (20min) / Electronics &ElectricalEx. 14: Mobile Phone (3): Join and Trim the Surfaces (15min) / Electronics &ElectricalEx. 15: Mobile Phone (4): Create the Part Geometry (10min) / Electronics &ElectricalEx. 16: Mobile Phone (5): Modify the Geometry (5min) / Electronics & Electrical


Mechanical DesignSolutions HA1: Healing Assistant

EDU-CAT-E-HA1-FCourse Code EDU-CAT-E-HA1-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-HA1-FI-V5R15 Foils: EDU-CAT-E-HA1-FF-V5R15 Exercises: EDU-CAT-E-HA1-FX-V5R15

ObjectivesIn this course, you will learn how to create valid closed topologies fromimported data, even inaccurate or invalid. The objective is to get suitable datafor further processing in V5 (example: tooling design).The course includes both theoretical descriptions and practical tips.

Participants' ProfileAll designers, especially in the tooling design domain

PrerequisitesGS1-F-V5R12: CATIA Surface Design

Content- How to analyze and repair imported data- How to create topology (Join)- How to close topology (Healing)- How to compare two versions of a part

What is new in this releaseCompare parts

ExercisesEx. 1: Lateral Fender (master exercise) (60min) / All sectorsEx. 2: Compare exercise: Lateral fender (30min) / All sectorsEx. 3: Additional exercise (Handle) (45min) / All sectors


Mechanical DesignSolutions LO1: 2D Layout to 3D Design

EDU-CAT-E-LO1-FCourse Code EDU-CAT-E-LO1-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-LO1-FI-V5R15 Foils: EDU-CAT-E-LO1-FF-V5R15 Exercises: EDU-CAT-E-LO1-FX-V5R15

ObjectivesIn this course you will learn how to draw benefit from 2D and 3D provided in asingle environment to design 3D products.


PrerequisitesDraftingPart DesignAssembly design

ContentAccessing the workbenchUser interfaceGeneral presentationMulti design views3D geometry creation from 2D geometryStandard managementAdvanced print capabilitiesDrawing creation from 2D layout

What is new in this releaseNew course

ExercisesEx. 1: Front rear sprocket creation (20min) / All sectorsEx. 2: Frontfork creation (60min) / All sectorsEx. 3: Tyre assembly modification and CATDrawing extraction (60min) / Allsectors


Mechanical DesignSolutions MD2: CATIA Mechanical Design V5R15 Update

EDU-CAT-E-MD2-UCourse Code EDU-CAT-E-MD2-UCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-MD2-UI-V5R15 Foils: EDU-CAT-E-MD2-UF-V5R15

ObjectivesIn this course, you will learn about the new and enhanced tools of theMechanical Design Workbenches in V5R15 Release

Participants' ProfileCATIA V5R15 Mechanical Designers

PrerequisitesCATIA Mechanical Design Courses

Content- Part Design Enhancements- Surface Design Enhancements- Drafting Enhancements

ExercisesEx. 1: Create a Shaft (5min) / All sectorsEx. 2: Create a Pattern (10min) / All sectorsEx. 3: Rotate a Feature (10min) / All sectorsEx. 4: Isoparametric Curve (10min) / All sectorsEx. 5: Create Extrude (5min) / All sectorsEx. 6: Create Rotation (10min) / All sectorsEx. 7: Create Trim (10min) / All sectorsEx. 8: Create a Breakout (5min) / All sectors


Mechanical DesignSolutions MTD: Mold Tooling Design

EDU-CAT-E-MTD-FCourse Code EDU-CAT-E-MTD-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MTD-FI-V5R15 Foils: EDU-CAT-E-MTD-FF-V5R15 Exercises: EDU-CAT-E-MTD-FX-V5R15 Detailed Steps: EDU-CAT-E-MTD-FS-V5R15

ObjectivesIn this course, you will learn how to use the workbench Mold Tooling Design tocreate a Plastic Injection Mold

Participants' ProfileNew Mold Tooling Design users

PrerequisitesTG1: Tooling Design (EDU-CAT-E-TG1-F - V5R15)

Content- Create a new mold- Edit the mold base- Manage Components- Create injection features- Manage user components- Manage the Bill of Material

What is new in this releaseUpdate to R15 level

ExercisesEx. 1: Phone Handset (240min) / All sectorsEx. 2: Cover (180min) / All sectors


Mechanical DesignSolutions PDG: CATIA Part Design Expert

EDU-CAT-E-PDG-ACourse Code EDU-CAT-E-PDG-ACATIA V5R15Brand & Release CATIA V5R151.5 daysDuration 1.5 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-PDG-AI-V5R15 Foils: EDU-CAT-E-PDG-AF-V5R15 Exercises: EDU-CAT-E-PDG-AX-V5R15 Detailed Steps: EDU-CAT-E-PDG-AS-V5R15 Detailed Steps: EDU-CAT-E-PDG-AS-V5R15

ObjectivesUpon completion of the course, students will be able to design and analyzecomplex solid parts, using methods allowing to optimize their futuremodification.

Participants' ProfileCATIA V5 Mechanical Designers.

PrerequisitesCATIA V5 Fundamentals, Getting started with CATIA V5, Sketcher, PartDesign, Product Design, Generative Drafting (ISO or ANSI).

Content- Using 3D Elements to Create a Part- Sketch-Based Features- Part Manipulations- Dress-Up Features- Part Analysis- Annotations

What is new in this releaseMaster Exercise Re-engineered.Part Manipulations Lesson improve (sharing geometry and booleanoperations).

ExercisesEx. 1: Sketch based Features Recap Exercises (45min) / All sectorsEx. 2: Meat Mincer Screw (45min) / All sectorsEx. 3: Using 3D Elements to Create a Part Recap Exercises (35min) / AllsectorsEx. 4: Hinge (40min) / All sectorsEx. 5: Dress Up Features (35min) / All sectorsEx. 6: Part Manipulations (35min) / All sectorsEx. 7: Part Analysis (25min) / All sectorsEx. 8: Master Exercise: Mobile Phone Bottom Case (90min) / All sectors


Mechanical DesignSolutions SMD: CATIA Generative Sheet Metal Design

EDU-CAT-E-SMD-FCourse Code EDU-CAT-E-SMD-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMD-FI-V5R15 Foils: EDU-CAT-E-SMD-FF-V5R15 Exercises: EDU-CAT-E-SMD-FX-V5R15 Detailed Steps: EDU-CAT-E-SMD-FS-V5R15

ObjectivesIn this course you will learn methods to create and modify sheet metal featuresand parts.


PrerequisitesCATIA V5 Fundamentals.

Content- Getting Started- Sheet Metal Walls- Bends, Unfolded Mode and Local Corner Relief- Flanges- Sheet Metal Features- Duplication- Mapping and Output- Advanced Topics in Sheet Metal Design- Master Exercise

What is new in this releaseThis course was updated in order to reflect the main CATIA V5R15enhancements.In addition, an adavanced lesson was added, containing two advanced topics:- Sheet Metal Standard Files- The Multi-Body Methodology

ExercisesEx. 1: Sheet Metal Walls (45min) / All sectorsEx. 2: Bends and Unfolded Mode (30min) / All sectorsEx. 3: Flanges Exercises (30min) / All sectorsEx. 4: Sheet Metal Features (40min) / All sectorsEx. 5: Duplication (55min) / All sectorsEx. 6: Part Modifications (20min) / All sectorsEx. 7: Mapping and Output (35min) / All sectorsEx. 8: Master Exercise: Casing Assembly (80min) / All sectorsEx. 9: Multi-Body Cover (45min) / All sectors


Mechanical DesignSolutions SMD: CATIA Generative Sheetmetal Design

V5R15 UpdateEDU-CAT-E-SMD-UCourse Code EDU-CAT-E-SMD-UCATIA V5R15Brand & Release CATIA V5R150.3 dayDuration 0.3 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesFoils: EDU-CAT-E-SMD-UF-V5R15 Instructor Foils: EDU-CAT-E-SMD-UI-V5R15

ObjectivesIn this course you will learn new and enhanced capabilities of V5 R15 inGenerative Sheetmetal Design workbench.


PrerequisitesCATIA Generative Sheetmetal Design

Content- User Interface Changes in V5R15- Sheet Metal Bends- Sheet Metal Standard Stamps- Sheet Metal Holes- Sheet Metal Drawings

ExercisesEx. 1: creating Closed Sheet Metal Bend (5min) / All sectorsEx. 2: Creating stamps with newoptions (10min) / All sectorsEx. 3: Creating holes in sheetmetal part (5min) / All sectors


Mechanical DesignSolutions SR1: Structure Design

EDU-CAT-E-SR1-FCourse Code EDU-CAT-E-SR1-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SR1-FI-V5R15 Foils: EDU-CAT-E-SR1-FF-V5R15 Exercises: EDU-CAT-E-SR1-FX-V5R15 Additional Information: EDU-CAT-E-SR1-FO-V5R15

ObjectivesIn this course you will learn methods to quickly create and modify linear andcurved structures, and plates using standard or user-defined sections. Itaddresses any kind of Frames, Foundations and Steel construction …, invarious domains like Aerospace, Automotive and F&A.

Participants' ProfileNew CATIA V5 users

PrerequisitesCOM, WFS, PDG


Content1.Introduction to Structure Designp7 Accessing the Workbench p8 Exploring the User Interfacep9 Terminologyp10 General Processp112.Options & Project Resources Managementp12 Setting Structure Design Optionsp13 Setting Part Design Options p14 Setting Assembly Design Optionsp17 Selecting a Projectp183.Creating Skeletonsp20 What about Skeletons?p21 Creating Grids in 3Dp224.Defining and Creating Shapes & Platesp25 What about Shapes? p26 Defining & Placing Shapes… p27 Sectionsp28 Defining Section to be Used p29 Defining Shape Anchor Point p31 Defining Shape Orientation p34 Placing Shapes Using Points p35 Placing Shapes on Support p38 Creating Plates & End-Platesp40 Creating Small Assemblies p435.Modifying Shapes & Platesp45 Modifying Shapes & Plates Definition p46 Extending and Stretching Shapesp48 Splitting and Merging Shapes & Platesp49 Coping Platesp50 Defining Cutbacks p52 Removing Cutbacks p58 Placing Cutoutsp59 Modifying Cutouts p62 Removing Cutouts p63 Placing End Cuts p64 Modifying and Removing End Cuts p68 Placing Slotsp69 Modifying Slotsp73 Removing Slotsp726.Making Design Changesp75 Modifying Structure Geometryp76

What is new in this releaseReference to multi-selection during re-specification of shapes

NotesWe have added, for this release, additional information to help the teacher toinstall a full project for the SR1 training (data and resources).

ExercisesEx. 1: External Turret: Panel System (45min) / All sectorsEx. 2: External Turret: Jacket System (30min) / All sectorsEx. 3: External Turret: Floor System (30min) / All sectorsEx. 4: External Turret: Detailing (90min) / All sectorsEx. 5: External Turret: Modifications (15min) / All sectorsEx. 6: External Turret: Secondary Structures (30min) / All sectors


Mechanical DesignSolutions SR1: Structure Design

EDU-CAT-E-SR1-ACourse Code EDU-CAT-E-SR1-ACATIA V5R15Brand & Release CATIA V5R154 daysDuration 4 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SR1-AI-V5R15 Foils: EDU-CAT-E-SR1-AF-V5R15 Exercises: EDU-CAT-E-SR1-AX-V5R15 Detailed Steps: EDU-CAT-E-SR1-AS-V5R15

ObjectivesIn this course you will learn methods to administrate a SR1 project.


PrerequisitesCOM, WFS, PDG, SR1, PKT, KWA (Optional)

Content1. Project Resource Managementp5 Introducing the PRMp6 Understanding the PRMp7 Structure Discipline Resourcesp11 Accessing the PRMp12 Checking the PRMp152. Feature Dictionaryp16 About the Feature Dictionaryp17 Starting the Feature Dictionary Editorp18 Managing Attributes p19 Discrete Valuesp21 Managing ID Numberp223. Standard Section Catalogsp24 Managing Parametric Sectionsp25 Generating Resolved Partsp30 Creating/Modifying Standard Section Catalogsp324. Detailing Featuresp34 Design Rules and Recommendationsp35 End-Cutsp38 Slotsp44 Small Assembliesp47 Storing Detailing Features in a catalogp50

What is new in this releaseBrand New Course and Exercises Content

ExercisesEx. 1: Creating a New Project (180min) / All sectorsEx. 2: Adding New Attributes (180min) / All sectorsEx. 3: Modifying a Standard Section Catalog (240min) / All sectorsEx. 4: Creating a Standard End-Cut (180min) / All sectorsEx. 5: Creating a Contextual End-Cut (180min) / All sectorsEx. 6: Creating a Slot (180min) / All sectorsEx. 7: Creating a Small Assembly (180min) / All sectors


Mechanical DesignSolutions TG1: Tooling Design

EDU-CAT-E-TG1-FCourse Code EDU-CAT-E-TG1-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TG1-FI-V5R15 Foils: EDU-CAT-E-TG1-FF-V5R15 Exercises: EDU-CAT-E-TG1-FX-V5R15 Detailed Steps: EDU-CAT-E-TG1-FS-V5R15

ObjectivesIn this course you will learn how to use workbench Tooling Design to createand instantiate Components in a Mold or Die Structure

Participants' ProfileNew Tooling Design users

PrerequisitesCATIA V5 FundamentalsMechanical Design Fundamentals (C511-MEC-E-F5 - V5R11)

ContentIntroduction to Tooling DesignCreating ComponentsEditing ComponentsSpecific Components : Inserts and SlidersAdvanced Drilling CapabilitiesManaging User ComponentsAnalyzing Holes in PlatesCreating the Bill of MaterialWorking with large assemblies : Cache Management

ExercisesEx. 1: Phone Handset (150min) / All sectors


Mechanical DesignSolutions V5E: CATIA V5 Expert Mechanical Designer

EDU-CAT-E-V5E-ACourse Code EDU-CAT-E-V5E-ACATIA V5R15Brand & Release CATIA V5R155 daysDuration 5 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5E-AI-V5R15 Foils: EDU-CAT-E-V5E-AF-V5R15

ObjectivesThe goals of the CATIA V5 Expert Mechanical Designer course are to teachyou how to start a complex design project from its specifications (top downapproach) and complete it by reusing existing designs.This course focuses on the advanced skills and concepts that enable you tocreate robust designs.

Participants' ProfileMechanical designers already having an experience of CATIA V5 mechanicaldesign foundations.

PrerequisitesTraining on CATIA V5 FundamentalsMechanical design experience

ContentLesson 1: IntroductionLesson 2: Design Complex PartsLesson 3: Surface DesignLesson 4: Analyze and Annotate PartsLesson 5: Sharing InformationLesson 6: Assembly DesignLesson 7: Design in ContextLesson 8: Complex Assembly DesignMaster Project 1: Mobile PhoneMaster Project 2: Lifting Truck

What is new in this releaseThis course was completly reengineered in R15.

NotesThe amount of pages indicated for the guide, corresponds to the sum of thevarious documents which compose it.


ExercisesEx. 1: Case Study: Introduction (40min) / AutomotiveEx. 2: Exercise 2A (20min) / All sectorsEx. 3: Exercise 2B (15min) / All sectorsEx. 4: Exercise 2C (20min) / All sectorsEx. 5: Exercise 2D (30min) / AutomotiveEx. 6: Exercise 2E (5min) / All sectorsEx. 7: Exercise 2F (30min) / All sectorsEx. 8: Exercise 2G (20min) / All sectorsEx. 9: Exercise 2H (20min) / All sectorsEx. 10: Exercise 2I (15min) / All sectorsEx. 11: Case Study: Design Complex Parts (40min) / Consumer PackagedGoodsEx. 12: Exercise 3A (20min) / All sectorsEx. 13: Exercise 3B (20min) / All sectorsEx. 14: Exercise 3C (5min) / All sectorsEx. 15: Exercise 3D (30min) / All sectorsEx. 16: Exercise 3E (20min) / Consumer Packaged GoodsEx. 17: Exercise 3F (20min) / All sectorsEx. 18: Exercise 3G (15min) / All sectorsEx. 19: Exercise 3H (20min) / Consumer Packaged GoodsEx. 20: Case Study: Surface Design (40min) / All sectorsEx. 21: Exercise 4A (20min) / AutomotiveEx. 22: Exercise 4B (20min) / All sectorsEx. 23: Exercise 4C (20min) / All sectorsEx. 24: Exercise 4D (20min) / All sectorsEx. 25: Exercise 5A (10min) / All sectorsEx. 26: Exercise 5B (10min) / All sectorsEx. 27: Exercise 5C (15min) / All sectorsEx. 28: Exercise 5D (20min) / All sectorsEx. 29: Exercise 5E (20min) / All sectorsEx. 30: Exercise 5F (20min) / All sectorsEx. 31: Case Study: Sharing Information (30min) / All sectorsEx. 32: Exercise 6A (15min) / All sectorsEx. 33: Exercise 6B (20min) / All sectorsEx. 34: Exercise 6C (20min) / All sectorsEx. 35: Exercise 6D (20min) / All sectorsEx. 36: Exercise 6E (20min) / All sectorsEx. 37: Exercise 6F (30min) / All sectorsEx. 38: Exercise 6G (10min) / All sectorsEx. 39: Case Study: Assembly Design (40min) / All sectorsEx. 40: Exercise 7A (20min) / All sectorsEx. 41: Exercise 7B (20min) / All sectorsEx. 42: Exercise 7C (20min) / All sectorsEx. 43: Exercise 7D (20min) / All sectorsEx. 44: Exercise 7E (20min) / All sectorsEx. 45: Exercise 7F (20min) / All sectorsEx. 46: Exercise 7G (30min) / All sectorsEx. 47: Case Study: Contextual Design (40min) / Consumer Packaged GoodsEx. 48: Exercise 8A (20min) / All sectorsEx. 49: Exercise 8B (20min) / All sectorsEx. 50: Exercise 8C (90min) / AutomotiveEx. 51: Exercise 8D (20min) / All sectorsEx. 52: Exercise 8E (30min) / All sectorsEx. 53: Case Study: Complex Assembly Design (80min) / All sectorsEx. 54: Master Project 1 (100min) / Electronics & ElectricalEx. 55: Master Project 2 (240min) / Fabrication & Assemblies ConsumerGoods


Mechanical DesignSolutions V5F: CATIA V5 Fundamentals

EDU-CAT-E-V5F-FCourse Code EDU-CAT-E-V5F-FCATIA V5R15Brand & Release CATIA V5R155 daysDuration 5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesFoils: EDU-CAT-E-V5F-FF-V5R15 Instructor Foils: EDU-CAT-E-V5F-FI-V5R15

ObjectivesThis course is the first within the CATIA V5 curriculum. Upon completion of thiscourse, the student will be able to describe the basic terminology and use thebasic features of the CATIA V5 Solutions. The students will be introduced tothe CATIA V5 fundamental concepts and interface, will learn the concept ofsketch-based features, dress-up features, the management of parts through anassembly and how to generate standard views from a part or assembly. Thepart creation in this course is mainly focused on the creation of parts based on2D profiles (sketches), and on the assembly of existing components.

Participants' ProfileNew CATIA V5 Mechanical Designers

PrerequisitesMechanical design experience.Experience with the Windows operating system.

Content- Lesson 1: Introduction to CATIA- Lesson 2: Profile Creation

- Lesson 3: Basic Features

- Lesson 4: Additional Features

- Lesson 5: Dress-Up Features

- Lesson 6: Reusing Data

- Lesson 7: Finalizing Design Intent

- Lesson 8: Assembly Design

- Lesson 9: Design in Context

- Lesson 10: Drafting ISO

- Lesson 10: Drafting ANSI

What is new in this releaseExercises 2C, 2F modified.Exercise 2E, 3C, 4E, 4F, 4I, Case study of lesson 4 and 5, 5C, 6C, 6Freengineered.Exercise 6B: CATpart associated file replaced.New Lesson10 for ISO drafting.


NotesThe exercises and detailed steps have been integrated in the Student Guide.The Student Guide must be assembled by using the cover document, TOC,and Lesson files.It is normal that the student and instructor guides do not contain the sameamount of information.The amount of pages indicated for the guide, corresponds to the sum of thevarious documents which compose it.

ExercisesEx. 1: Key Terms & Design Intent Exercise: 1A (20min) / All sectorsEx. 2: Getting Started with CATIA Exercise: 1B (20min) / All sectorsEx. 3: Case Study: Drill Press Master Project (20min) / All sectorsEx. 4: Create New Part Exercise: 2A, 2B, 2C (40min) / All sectorsEx. 5: Constraining a Sketch Exercise: 2D, 2E, 2F (40min) / All sectorsEx. 6: Case Study: Support Plate (15min) / All sectorsEx. 7: Creating with Basic Features Exercise: 3A, 3B, 3C (40min) / All sectorsEx. 8: Part Investigation Exercise: 3D, 3E (20min) / All sectorsEx. 9: Case Study: Engine Support (20min) / All sectorsEx. 10: Create with Additional Features Exercise: 4A, 4B, 4C (45min) / AllsectorsEx. 11: Create Revolved Features Exercise: 4D, 4E, 4F (45min) / All sectorsEx. 12: Create Shell and Thin Features Exercise: 4G, 4H, 4I (50min) / AllsectorsEx. 13: Case Study: Handle Block (20min) / All sectorsEx. 14: Create Dress-up Features Exercise: 5A, 5B, 5C (50min) / All sectorsEx. 15: Editing Features Exercise: 5D, 5E, 5F (50min) / All sectorsEx. 16: Case Study: Casing Support (25min) / All sectorsEx. 17: Reusing Data Exercise: 6A, 6B, 6C (50min) / All sectorsEx. 18: Reusing Data Part 2 Exercise: 6D, 6E, 6F (50min) / All sectorsEx. 19: Case Study: Engine (35min) / All sectorsEx. 20: Finalizing Design Intent Exercise: 7A, 7B, 7C, 7D, 7E (80min) / AllsectorsEx. 21: Case Study: Table (35min) / All sectorsEx. 22: Introduction to Assembly Design Exercise: 8A, 8B, 8C (50min) / AllsectorsEx. 23: Adding Assembly Design Components Exercise: 8D, 8E, 8F (60min) /All sectorsEx. 24: Case Study: Handle Mechanism (35min) / All sectorsEx. 25: Design in Context Exercise: 9A, 9B, 9C, 9D, 9E (120min) / All sectorsEx. 26: Case Study: Chuck (30min) / All sectorsEx. 27: Creating the Drawing Exercise: 10A, 10B, 10C (30min) / All sectorsEx. 28: Case Study: Base (20min) / All sectorsEx. 29: Master Project: Part Creation (60min) / All sectorsEx. 30: Master Project: Finalize the Part (45min) / All sectorsEx. 31: Master Project: Create an Assembly (60min) / All sectorsEx. 32: Master Project: Edit a Part (40min) / All sectorsEx. 33: Master Project: Create a Drawing (20min) / All sectors



Machining Solutions


MachiningSolutions AMG: Advanced Part Machining

EDU-CAT-E-AMG-FCourse Code EDU-CAT-E-AMG-FCATIA V5R15Brand & Release CATIA V5R151.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-AMG-FI-V5R15 Foils: EDU-CAT-E-AMG-FF-V5R15 Exercises: EDU-CAT-E-AMG-FX-V5R15 Demonstration: EDU-CAT-E-AMG-FD-V5R15

ObjectivesIn this course, you will learn how to define:- Multi-Axis Flank Contouring operation- Multi-Axis Helix machining operation- Cavities Roughing operation

Participants' ProfileManufacturing users knowing how to work with CATIA V5 parts

PrerequisitesFundamentals about CATIA V5

Content- Multi Axis Flank Contouring operation presentation- Geometry tab- Strategy tab- Multi Axis Helix machining operation presentation- Geometry tab- Strategy tab- Cavities Roughing operation presentation- Geometry tab- Strategy tab

What is new in this releaseAdditionnal information concerning offset management

ExercisesEx. 1: Multi-Axis Contouring operation (20min) / All sectorsEx. 2: Flank finishing (5min) / All sectorsEx. 3: Start and End in closed pocket (5min) / All sectorsEx. 4: Joggle management (5min) / All sectorsEx. 5: Thickness on tool path (5min) / All sectorsEx. 6: Curves as part (5min) / All sectorsEx. 7: Local modifications (10min) / All sectorsEx. 8: Non contiguous drives (10min) / All sectorsEx. 9: Non contiguous drives 2 (10min) / All sectorsEx. 10: Non contiguous drives in same plane (10min) / All sectorsEx. 11: Auxilliary guiding (10min) / All sectorsEx. 12: Mx-Helix 01 : Rough body blade / All sectorsEx. 13: Mx-Helix 02 : Rough foot blade (10min) / All sectorsEx. 14: Mx-Pocket 01 : Rough Frame (10min) / All sectorsEx. 15: Mx-Pocket 02 : Rough Zone (10min) / All sectorsEx. 16: Mx-Helix 03 : Interpol (10min) / All sectors


MachiningSolutions LMG: Lathe Machining

EDU-CAT-E-LMG-FCourse Code EDU-CAT-E-LMG-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-LMG-FI-V5R15 Foils: EDU-CAT-E-LMG-FF-V5R15 Exercises: EDU-CAT-E-LMG-FX-V5R15 Detailed Steps: EDU-CAT-E-LMG-FS-V5R15

ObjectivesAt the end of this course, participants will be able to define and manage NCprograms dedicated to machining parts using Lathe machining technics.

Participants' ProfileManufacturing users knowing how to work with Turning processes

PrerequisitesFundamentals about CATIA V5NC Manufacturing Infrastructure

ContentLathe Operations- Rough Turning- Groove Turning- Recess Turning- Profile Finish Turning- Groove finish Turning- Thread Turning- Sequential Turning- Ramp Rough Turning- Ramp Recess Turning- Lathe Tool assembly

- Design Associativity- Machining Process for Lathe operation creation

- Methodologies for Groove Turning- Turning on Milling Center with Facing Head

ExercisesEx. 1: Cylindrical Structure Part (130min) / All sectors


MachiningSolutions MMG: Multi-Axis Surface Machining

EDU-CAT-E-MMG-FCourse Code EDU-CAT-E-MMG-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MMG-FI-V5R15 Foils: EDU-CAT-E-MMG-FF-V5R15 Exercises: EDU-CAT-E-MMG-FX-V5R15

ObjectivesIn this course, you will learn how to define and manage NC programs tomachine Surface or Solid geometry using 5-Axis machining techniques.

Participants' ProfileManufacturing users

PrerequisitesFundamentals about CATIA V5NC Manufacturing Infrastructure3-Axis Surface Machining

Content- Multi-Axis Sweeping Operation- Multi-Axis Contour Driven Operation- Multi-Axis Curve Machining Operation- Multi-Axis Isoparametric Machining Operation- Multi-Axis Drilling Operation

ExercisesEx. 1: Fender (90min) / All sectorsEx. 2: Hood (40min) / AutomotiveEx. 3: Pocket (15min) / All sectorsEx. 4: Isoparametric and Drill (15min) / All sectors


MachiningSolutions MPA: Prismatic Machining Preparation Assistant

EDU-CAT-E-MPA-FCourse Code EDU-CAT-E-MPA-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MPA-FI-V5R15 Foils: EDU-CAT-E-MPA-FF-V5R15 Exercises: EDU-CAT-E-MPA-FX-V5R15 Detailed Steps: EDU-CAT-E-MPA-FS-V5R15

ObjectivesIn this course you will see how to define and manage NC programs to machineparts designed in 3D Wireframe or Solid geometry with 2.5 Axis machiningoperations and how this product assists the NC programmer in making the linkbetween Design and Manufacturing.

Participants' ProfileManufacturing users knowing how to work with CATIA V5 Parts and Processes

PrerequisitesCATIA V5 FundamentalsPMG-F: Prismatic Machining

Content- Introduction to Prismatic Machining Preparation Assistant- Global features recognition- Locall features recognition - Machinable Axial Features Pattern Creation

What is new in this releasePattern creation along with features recognitionAdvanced optionsRetrieve fitting tolerances from design featuresEnhancement in geometry selection for Manual feature creation

ExercisesEx. 1: Prismatic Part (60min) / All sectorsEx. 2: Holes management (15min) / All sectors


MachiningSolutions MPG: Multi Pocket Machining

EDU-CAT-E-MPG-FCourse Code EDU-CAT-E-MPG-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MPG-FI-V5R15 Foils: EDU-CAT-E-MPG-FF-V5R15 Exercises: EDU-CAT-E-MPG-FX-V5R15 Detailed Steps: EDU-CAT-E-MPG-FS-V5R15

ObjectivesIn this course, you will learn how to define:- Power Machining operation

Participants' ProfileManufacturing users knowing how to work with CATIA V5 parts

PrerequisitesFundamentals about CATIA V5Users already trained with other milling course

Content- Power machining operation presentation- Geometry tab- Strategy tab- Offsets management

ExercisesEx. 1: Power machining frame (15min) / All sectors


MachiningSolutions NCI: Numerical Control Infrastructure

EDU-CAT-E-NCI-FCourse Code EDU-CAT-E-NCI-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-NCI-FI-V5R15 Foils: EDU-CAT-E-NCI-FF-V5R15 Exercises: EDU-CAT-E-NCI-FX-V5R15 Detailed Steps: EDU-CAT-E-NCI-FS-V5R15 Additional Information: EDU-CAT-E-NCI-FO-V5R15

ObjectivesAt the end of this course, participants will be able to use Common platform for2.5 to 5-axis axis machining capabilities

Participants' ProfileManufacturing users knowing how to work with CATIA V5 NC Manufacturing

PrerequisitesFundamentals about CATIA V5

ContentCOMMON TOPICSLesson 1 : Workbench PresentationLesson 2 : Define Setup (Part Operation)Lesson 3 : Machining Operation, Macros, Tools PresentationLesson 4 : Tool Path Verification & Simulationlesson 5 : Auto sequencelesson 6 : Auxiliary Operationslesson 7 : Output generationlesson 8 : Axial Operationslesson 9 : Hole selection - Machining Pattern Managementlesson 10 : The different Process ViewsLesson 11 : Geometry wizard (edge, surface)

ADVANCED TOPICSLesson 12 : Import & Modify Tool PathLesson 13 : Resource ManagementLesson 14 : PP Word Table customizationLesson 15 : V4 NCMill & NCLathe Set Import (optional)Lesson 16 : Design Change ManagementLesson 17 : Machining Processes

APPENDIXSettings


NotesThe training is composed of 3 Parts Common tasks : with regroup that is imperative to know (basic task)Advanced Task : for advanced users how want to know more about NCProcesses and managementAppendix : which regroup Tool/option setting

It is not necessary to do all the course but it’s imperative to do the first Part(Common tasks)According the level of the attendees you will found in the second part some element to answer, explain and practice on more sharp topics

The COMMON TASKS is composed of different chapters, for most chapter youhave a part called “More details”It recommended to not describe to the attendees this part and go directly to thenext chapter This “more details” chapter explain each options of a functionality then it can beuse if the attendees want to know the meaning of a specific option

ExercisesEx. 1: CATProcess & Workbencg Presentation (5min) / All sectorsEx. 2: Machining Operation Presentation (15min) / All sectorsEx. 3: Replay Simulate and analyze (15min) / All sectorsEx. 4: Generate Auxiliary operation (30min) / All sectorsEx. 5: Generate Outputs (15min) / All sectorsEx. 6: Create Spot drilling and a drilling Operations (15min) / All sectorsEx. 7: Import APT source File (30min) / All sectorsEx. 8: Manage Resources (30min) / All sectorsEx. 9: Auto Complete (30min) / All sectorsEx. 10: PP Word Table (30min) / All sectorsEx. 11: Import V4 NC data (NCMill / NCLathe) (30min) / All sectorsEx. 12: Design Change (30min) / All sectorsEx. 13: Machining Process creation & instantiation (60min) / All sectors


MachiningSolutions PMG: Prismatic Machining

EDU-CAT-E-PMG-FCourse Code EDU-CAT-E-PMG-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PMG-FI-V5R15 Foils: EDU-CAT-E-PMG-FF-V5R15 Exercises: EDU-CAT-E-PMG-FX-V5R15 Detailed Steps: EDU-CAT-E-PMG-FS-V5R15

ObjectivesAt the end of this course, participants will be able to define and manageprismatic (2,5 axis) operations, being aware of all capabilities in terms ofstrategies, parameters and transition paths.

Participants' ProfileManufacturing users knowing how to work with CATIA V5 Parts

PrerequisitesFundamentals about CATIA V5 and Machining

ContentMilling operations: - Facing,- Pocketing, - Prismatic Roughing,- Profile contouring,- Groove milling,- Point to point, - Curve following, - Prismatic rework area,- Prismatic machining area,- Transition Paths (macros)

ExercisesEx. 1: Aerospace structure part (130min) / All sectorsEx. 2: Prismatic Part (180min) / All sectorsEx. 3: Fitting Part (120min) / All sectorsEx. 4: Flap Track part (180min) / All sectorsEx. 5: AIrframe part (30min) / All sectors


MachiningSolutions SMG: Surface Machining

EDU-CAT-E-SMG-FCourse Code EDU-CAT-E-SMG-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMG-FI-V5R15 Foils: EDU-CAT-E-SMG-FF-V5R15 Exercises: EDU-CAT-E-SMG-FX-V5R15 Detailed Steps: EDU-CAT-E-SMG-FS-V5R15 Additional Information: EDU-CAT-E-SMG-FO-V5R15

ObjectivesIn this course, you will see how to define and manage NC programs dedicatedto machining parts designed with Surface or Solid geometry using 3-Axismachining techniques.

Participants' ProfileManufacturing users

PrerequisitesFundamentals about CATIA V5 and Machining

ContentIntroduction to the 3-Axis Surface Machining Accessing the Workbench Workbench the user interface Process/Product/Resources model Manufacturing terminology General process

Creating geometrical elements Creates rough stock Inserts an STL file Creates a stock by offset Points creation wizard Limit lines projection wizard Limit lines creation wizard

Creating a Machining Feature Geometrical Zone Creation Machining/Slope Area Creation Rework Area Creation Offset group Creation

Creating a 3-Axis Surface Machining Operation 3-Axis Machining Operations Sweep Roughing Operation Roughing Operation Sweeping Operation Pencil Operation Zlevel Operation Contour-driven Operation Isoparametric machining Operation Spiral milling Operation Profile Contouring Operation

Analysing and modifying tool path


What is new in this release- ool Gage :Compute Tool Gage on Assembly computes the minimum toolgage. The information generated can be saved as a .txt file. - Tool path editor : With the Split on collision points command, you can select anew tool and generate a new operation applied on the points in collision.

NotesThis course is linked to NCI course.

ExercisesEx. 1: Master exercise Renfort (140min) / All sectorsEx. 2: Create a roughing operation (30min) / All sectorsEx. 3: Create an isoparametric machining operation (30min) / All sectorsEx. 4: Create a spiral milling operation (30min) / All sectorsEx. 5: Create NC geometrical element, slope area and rework area (30min) /All sectorsEx. 6: Create a contouring operation (30min) / All sectorsEx. 7: Analyse and modify a computed tool path (20min) / All sectors


MachiningSolutions STL: STL Rapid Prototyping

EDU-CAT-E-STL-FCourse Code EDU-CAT-E-STL-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-STL-FI-V5R15 Foils: EDU-CAT-E-STL-FF-V5R15 Exercises: EDU-CAT-E-STL-FX-V5R15

ObjectivesIn this course, you will learn how to create meshes from solids or surfacesusing the application STL Rapid Prototyping.

Participants' ProfileSurface Designer

PrerequisitesDSE-F: Digitized Shape Editor

Content- Creating a STL from a basic Surface- Tuning the STL- Giving a thickness to the STL file- Exporting the STL file

ExercisesEx. 1: Portable Vacuum Cleaner (40min) / Fabrication & Assemblies ConsumerGoods



Product Synthesis Solutions


Product SynthesisSolutions HMN: Human Modeling

EDU-CAT-E-HMN-FCourse Code EDU-CAT-E-HMN-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-HMN-FI-V5R15 Foils: EDU-CAT-E-HMN-FF-V5R15 Exercises: EDU-CAT-E-HMN-FX-V5R15 Detailed Steps: EDU-CAT-E-HMN-FS-V5R15

ObjectivesIn this course, you will learn how to use our Human Model technology in orderto leverage your ergonomics analysis. Among other things, you will learn howto position and manipulate the manikins within a V5 Scene. In addition, you willevaluate the comfort, the reach, Clearance, and the vision of your targetpopulation. Additional to standard Ergonomics analysis you will evaluateinteraction between the manikin and geometries in the scene. Finally, you willrealize a simulation (animation).

Participants' Profile- Designers- Engineers- Human factors specialists- Any Health specialist

PrerequisitesCourse on Digital mock-up

Content- You will use the Ergonomics Design & Analysis tools to review theergonomics aspect of a manikin inside and around a vehicle, with the tools ofthe workbenches: Human Builder, Human Measurement Editor, HumanActivity Analysis and Human Postural Analysis.

ExercisesEx. 1: Ergonomics review inside a vehicle with Human Measurement Editor(240min) / AutomotiveEx. 2: Ergonomics review inside a vehicle with Human Postural Analysis(240min) / AutomotiveEx. 3: Ergonomics review around a vehicle with Human Activity Analysis(240min) / AutomotiveEx. 4: Ergonomics review inside a vehicle with Human Builder (240min) /Automotive


Product SynthesisSolutions KWA: Knowledge Advisor

EDU-CAT-E-KWA-FCourse Code EDU-CAT-E-KWA-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWA-FI-V5R15 Foils: EDU-CAT-E-KWA-FF-V5R15 Exercises: EDU-CAT-E-KWA-FX-V5R15 Detailed Steps: EDU-CAT-E-KWA-FS-V5R15

ObjectivesAt the end of this course, participants will be able to use Knowledge Advisorfeatures in order to:•embed knowledge in the designs•add technological and customer semantic•define morphing products•enrich product definition•automate product modifications and propagation•accelerate exploration of design alternatives•capture the design intent, preserve and share it


PrerequisitesCATIA V5 Basics

Content-Workbench presentation-Creating user parameters and formulas-Defining Checks, Rules, Reactions, Lists, Laws, Loops and macros witharguments-Associating URLs to parameters or relations-Running macros from Rules or Reactions-Using the Knowledge Inspector tool-Managing Design Tables and part family catalogs

What is new in this release-new samples data- handling errors in rules- creating a loop in a Reaction- populating a List with a query- creating geometry from rules

ExercisesEx. 1: Wheel Rim (90min) / All sectorsEx. 2: Light Bulb (60min) / All sectorsEx. 3: Sheet Metal Part (30min) / All sectors


Product SynthesisSolutions KWE: Knowledge Expert

EDU-CAT-E-KWE-FCourse Code EDU-CAT-E-KWE-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWE-FI-V5R15 Foils: EDU-CAT-E-KWE-FF-V5R15 Exercises: EDU-CAT-E-KWE-FX-V5R15 Detailed Steps: EDU-CAT-E-KWE-FS-V5R15

ObjectivesIn this course you will learn the functionalities of CATIA V5R15 KnowledgeExpert product : creation and use of expert rules, expert checks, solving of rulebases, generation of check reports and management of User Defined Featuretypes. For the creation of rules and checks, you will learn how to use theObject Browser tool.

Participants' ProfileUsers implementing the Know-how on the design quality as design rules,security norms and company standards.

PrerequisitesCATIA V5 Basics

Content- Workbench presentation- Creating a rule base and a rule set- Creating an expert rule- Creating an expert check- Navigating the object browser- Accessing the Expert Check/Rule in the Check/Rule body- Solving a rule base- Generating a check report- Performing a Global Analysis of Checks- Working with rule bases and catalogs- Creating expert rules or expert checks on User Features

ExercisesEx. 1: Connector (40min) / All sectorsEx. 2: LBlock Correction (40min) / All sectors


Product SynthesisSolutions KWF: Knowledge Fundamentals

EDU-CAT-E-KWF-FCourse Code EDU-CAT-E-KWF-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWF-FI-V5R15 Foils: EDU-CAT-E-KWF-FF-V5R15 Exercises: EDU-CAT-E-KWF-FX-V5R15 Detailed Steps: EDU-CAT-E-KWF-FS-V5R15

ObjectivesAt the end of this course, trainees should be able to create and use parametricparts and assemblies, without any help.

Participants' ProfileMechanical design engineer with project management responsibilities.

PrerequisitesPDG-F: Part Design FundamentalsASS-F: Assembly Design Fundamentals

Content- Introduction to knowledge tools- Common Knowledge Tools- Collaborative Work and Knowledge

ExercisesEx. 1: Common Knowledge Tools Exercise : Bolt and Stringer (40min) / AllsectorsEx. 2: Collaborative Work and Knowledge Exercise : Grip Assembly (45min) /All sectorsEx. 3: Stringer Assembly - Step 1 : Creating user parameters and formulas(10min) / All sectorsEx. 4: Stringer Assembly - Step 2 : Importing Rules and Checks (10min) / AllsectorsEx. 5: Stringer Assembly - Step 3 : Using a Design Table (10min) / All sectorsEx. 6: Stringer Assembly - Step 4 : Publishing Parameters (5min) / All sectorsEx. 7: Stringer Assembly - Step 5 : Creating User Parameters and formulas(10min) / All sectorsEx. 8: Stringer Assembly - Step 6 :Using parameters as external references(15min) / All sectorsEx. 9: Stringer Assembly - Step 7 : Replacing component (5min) / All sectors


Product SynthesisSolutions PEO: Product Engineering Optimizer

EDU-CAT-E-PEO-FCourse Code EDU-CAT-E-PEO-FCATIA V5R15Brand & Release CATIA V5R150.7 dayDuration 0.7 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PEO-FI-V5R15 Foils: EDU-CAT-E-PEO-FF-V5R15 Exercises: EDU-CAT-E-PEO-FX-V5R15 Detailed Steps: EDU-CAT-E-PEO-FS-V5R15

ObjectivesIn this course, you will learn the functionalities of CATIA Product EngineeringOptimizer (PEO): - Definition of an optimization problem- Specification of the optimization algorithm,- Solving of an optimization problem,- Analyzing and reporting on the results, - Use of the Design of Experiments tool to understand the behavior of a systemthanks to space exploration,- Use of the Constraint Satisfaction tool to solve complex contraint problems(with no objective function)

Participants' ProfileCATIA V5 Users

PrerequisitesCATIA Basics

Content- Workbench Presentation- Optimization Problem Formulation- Optimization problem resolution- Solution analysis- Best practices for optimization with PEO- Design of Experiments tool- Constraint Satisfaction tool

What is new in this release-Run optimization without filling the Undo Log

NotesDetailed Step only for master exercise \"Strap tension optimization\"

ExercisesEx. 1: Strap tension optimization (90min) / All sectorsEx. 2: Beam mass optimization (30min) / All sectorsEx. 3: Shape optimization: Hanger (40min) / All sectorsEx. 4: Fastener Shape Optimization (30min) / All sectorsEx. 5: Surfacic structure Structural Optimization (20min) / All sectorsEx. 6: Child Swing Structural Optimization (25min) / All sectorsEx. 7: Silo Structural Optimization (30min) / All sectorsEx. 8: Design of experiments (30min) / All sectorsEx. 9: Beam Mass Minimization through Constraint Satisfaction (20min) / Allsectors



Shape Design & Styling Solutions


Shape Design & StylingSolutions DL1: Developed Shapes

EDU-CAT-E-DL1-FCourse Code EDU-CAT-E-DL1-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-DL1-FI-V5R15 Foils: EDU-CAT-E-DL1-FF-V5R15 Exercises: EDU-CAT-E-DL1-FX-V5R15 Detailed Steps: EDU-CAT-E-DL1-FS-V5R15

ObjectivesThe objectives of these documents are to have the users familiar with developwires and unfolded surfaces concepts and functionalities


PrerequisitesWFS-F: Wireframe and Surface DesignGSD-F: Generative Shape Design

ContentUser interface and functionalitiesUser interfaceUnfolded surfaces Unfolded surfaces: Concept definition Unfolded surfaces functionalitiesDevelop wires Develop wires: Concept definition Develop wires: functionalitiesExercise PresentationTo Sum Up

ExercisesEx. 1: Water bottle and its support (40min) / All sectors


Shape Design & StylingSolutions DSE: Digitized Shape Editor

EDU-CAT-E-DSE-FCourse Code EDU-CAT-E-DSE-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-DSE-FI-V5R15 Foils: EDU-CAT-E-DSE-FF-V5R15 Exercises: EDU-CAT-E-DSE-FX-V5R15

ObjectivesIn this course, you will learn how to import digitized data and prepare it forfurther processing in CATIA



Content- Introduction to Digitized Shape Editor Workbench Presentation - Fundamentals of Digitized Shape Editor Point Processing Facetting the Cloud of Points Creating Curves Exporting files- Advanced Lesson Point Processing Checking results Mesh and Offset

ExercisesEx. 1: Car Door (80min) / AutomotiveEx. 2: Hair Dryer (75min) / Fabrication & Assemblies Consumer Goods


Shape Design & StylingSolutions FSK: FreeStyle Sketch Tracer

EDU-CAT-E-FSK-FCourse Code EDU-CAT-E-FSK-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FSK-FI-V5R15 Foils: EDU-CAT-E-FSK-FF-V5R15

ObjectivesIn this course, you will learn to create Class A surfaces from stylist’s drawingsor pictures.

Participants' ProfileSurface Designers


Content- Import an image- Position an image

ExercisesNone


Shape Design & StylingSolutions FSS: FreeStyle Shaper, Optimizer & Profiler

EDU-CAT-E-FSS-FCourse Code EDU-CAT-E-FSS-FCATIA V5R15Brand & Release CATIA V5R151.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FSS-FI-V5R15 Foils: EDU-CAT-E-FSS-FF-V5R15 Exercises: EDU-CAT-E-FSS-FX-V5R15

ObjectivesIn this course, you will learn how to create style design surfaces, analyze theirquality and modify them. You will discover two possible approaches: thesurface based approach and the curve based approach.

Participants' ProfileSurface Designers


ContentSurface Approach Step 1: Create the body of the hairdryerStep 2: Create the handle ofthe hairdryerStep 3: Blend the body and the handleStep 4: Globalmodification, offset, symmetryCurve Approach Step 1: Create the center parts (Hood, Windshield, Roof…)Step 2:Create the Side PanelStep 3: Create the Wheel ArchStep 4:Adjust shape through associativity

What is new in this release- New exercise on car example

ExercisesEx. 1: Hair Dryer - Surface Approach (140min) / All sectorsEx. 2: SEA-Car - Curve Approach (180min) / Automotive


Shape Design & StylingSolutions GSD: Surface Design Expert

EDU-CAT-E-GSD-FCourse Code EDU-CAT-E-GSD-FCATIA V5R15Brand & Release CATIA V5R152 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GSD-FI-V5R15 Foils: EDU-CAT-E-GSD-FF-V5R15 Exercises: EDU-CAT-E-GSD-FX-V5R15 Detailed Steps: EDU-CAT-E-GSD-FS-V5R15 Detailed Steps: EDU-CAT-E-GSD-FS-V5R15

ObjectivesThe objectives of this course is to cover advanced tools found in the GSDworkbench under the HD2 configuration and to better understand surfacingmethodology issues.

Participants' ProfileMechanical Surface Designers

PrerequisitesGS1: CATIA Surface Design (EDU-CAT-E-GS1-F - V5R14)and 200 hours experience.

Content- Surface Design Overview- Creating Advanced Wireframe Geometry- Wireframe Analysis and Repair- Common Tools for Swept Surfaces- Creating Advanced Swept Surfaces- Creating Advanced Blend Surfaces- Surface Analysis and Repair- Managing Features and Open Bodies- Hybrid Design

What is new in this releaseThis course was updated in order to reflect the main CATIA V5R14enhancements

NotesThe "Knob" exercise was re-engineered.The "Mobile Phone" exercise was improved.

ExercisesEx. 1: Advanced Wireframe Geometry (15min) / All sectorsEx. 2: Wireframe Analysis and Repair (10min) / All sectorsEx. 3: Shampoo Bottle (40min) / All sectorsEx. 4: Knob (60min) / All sectorsEx. 5: Advanced Swept Surfaces (30min) / All sectorsEx. 6: Mobile Phone (60min) / All sectorsEx. 7: Advanced Blending Surface (30min) / All sectorsEx. 8: Surface Analysis (30min) / All sectorsEx. 9: Hybrid Design (30min) / All sectorsEx. 10: Mirror Shell (60min) / All sectorsEx. 11: Plastic Bottle (180min) / All sectors


Shape Design & StylingSolutions GSD: CATIA Generative Shape Design V5R15

UpdateEDU-CAT-E-GSD-UCourse Code EDU-CAT-E-GSD-UCATIA V5R15Brand & Release CATIA V5R150.1 dayDuration 0.1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GSD-UI-V5R15 Foils: EDU-CAT-E-GSD-UF-V5R15

ObjectivesIn this course you will learn about the enhanced tools of the Generative ShapeDesign in V5R15 Release for the HD2 configuration.

Participants' ProfileMechanical Surface Designers

PrerequisitesSurface Design Expert

Content- Multiple Extract- Associative Isoparametric Curve- Extrude Up-to Surface- Multiple Trim- New Methods for Defining Angle in Rotation- Other Improvements

ExercisesEx. 1: Create Multiple Extract (10min) / All sectorsEx. 2: Isoparametric Curve (10min) / All sectorsEx. 3: Create Extrude (5min) / All sectorsEx. 4: Create Trim (10min) / All sectorsEx. 5: Create Rotation (10min) / All sectors


Shape Design & StylingSolutions GSO: Generative Shape Optimizer

EDU-CAT-E-GSO-FCourse Code EDU-CAT-E-GSO-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GSO-FI-V5R15 Foils: EDU-CAT-E-GSO-FF-V5R15 Exercises: EDU-CAT-E-GSO-FX-V5R15 Detailed Steps: EDU-CAT-E-GSO-FS-V5R15

ObjectivesUpon completion of the course, students will be able to optimize previouslybuilt surfaces, develop curves, create junctions, diabolos, and generatevolumes and Boolean operations.


PrerequisitesCATIA V5 Fundamentals, CATIA Surface Design.

ContentIntroduction to Generative Shape Optimizer - Accessing Generative Shape Optimizer - The User Interface - Developing wire - Creating junctions - Creating a Diabolo Seat - Creating bumped surfaces - Deforming surfaces according to curve wrapping - Deforming surfaces according to surface wrapping - Shape Morphing - Variable Offset - Rough OffsetCreating Volumes - What is a Volume - Types of Volumes - Volumes made from Sketches - Volumes made from Surfaces - Dress-up features on Volumes - Volumes using Boolean operations - Volumes from Operations or Transformations

What is new in this releaseIn R15, a new exercise was added: Steering Wheel.

ExercisesEx. 1: Door Junction (40min) / All sectorsEx. 2: Holding Arm (30min) / All sectorsEx. 3: Torch (40min) / All sectorsEx. 4: Steering Wheel (60min) / Automotive


Shape Design & StylingSolutions IMA: Imagine & Shape

EDU-CAT-E-IMA-FCourse Code EDU-CAT-E-IMA-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-IMA-FI-V5R15 Foils: EDU-CAT-E-IMA-FF-V5R15 Exercises: EDU-CAT-E-IMA-FX-V5R15

ObjectivesUse IMA workbench to quickly create complex surfaces.

Participants' ProfileThis course is targeted mainly for CATIA:Application engineersMechanical DesignersIndustrial Designers

PrerequisitesGenerative Shape Design


ContentIntroduction to Imagine & Shape

Add Complementary ToolsRecommended SettingsAccess the WorkbenchFunctions DescriptionToolbars DescriptionShortcutsGeneral BehaviorGeneral Tools / Selection

Surface creation:-Surface Manipulation-Introduction-Toolbar-Manipulation-Translation-Rotation-Scaling-Weight attributes-Vertex alignment

Surface refinement / Topology modification:-Extrusion-Section insertion-Subdivision-Face deletion-Edge extrusion

Curve creation:-Curve deformation-Sketching-Manipulate point-Smoothing-Fillet-Erase-On plane

Curve association to surface Compass definition

Sample shapes:-Square-Cylinder-Tube-Pyramid-Cone-Torus-Circle

Methodological advices

What is new in this releaseNew course

ExercisesEx. 1: Perfume bottle (40min) / All sectorsEx. 2: Hair Dryer (40min) / All sectorsEx. 3: Video Projector (50min) / All sectors


Shape Design & StylingSolutions PHS: Photo Studio

EDU-CAT-E-PHS-FCourse Code EDU-CAT-E-PHS-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PHS-FI-V5R15 Foils: EDU-CAT-E-PHS-FF-V5R15 Exercises: EDU-CAT-E-PHS-FX-V5R15 Detailed Steps: EDU-CAT-E-PHS-FS-V5R15

ObjectivesIn this course, you will learn how to create a photo realistic image

Participants' ProfileNew CATIA V5 Users


Content- Environment management- Camera management- Light sources management- Shooting management- Textures management- Stickers management- Animation: Turntable management- Animation: Animating scene elements

ExercisesEx. 1: Phone Handset (150min) / Fabrication & Assemblies Consumer GoodsEx. 2: Sport Car / Automotive


Shape Design & StylingSolutions PSO: Photo Studio Optimizer

EDU-CAT-E-PSO-FCourse Code EDU-CAT-E-PSO-FCATIA V5R15Brand & Release CATIA V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PSO-FI-V5R15 Foils: EDU-CAT-E-PSO-FF-V5R15

ObjectivesIn this course, you will learn how to use advanced options to create a photorealistic image


PrerequisitesCATIA BasicsCATIA Photo Studio

Content- 3D textures- Bump mapping- Global illumination- Caustics- Visual effects

ExercisesNone


Shape Design & StylingSolutions QSR: Quick Surface Reconstruction

EDU-CAT-E-QSR-FCourse Code EDU-CAT-E-QSR-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-QSR-FI-V5R15 Foils: EDU-CAT-E-QSR-FF-V5R15 Exercises: EDU-CAT-E-QSR-FX-V5R15

ObjectivesIn this course, you will learn how to quickly rebuild a rough surface model on acloud of points.


PrerequisitesCATIA Surface DesignDigitized Shape EditorFreeStyle

Content- Create scans on a cloud of points- Create curves on a cloud or from scans- Create surfaces close to cloud- Create curve networks- create surfaces from curve networks

ExercisesEx. 1: Plastic Bottle (120min) / Fabrication & Assemblies Consumer GoodsEx. 2: Exercise 2 : Washing Powder Bottle (120min) / Fabrication & AssembliesConsumer GoodsEx. 3: Exercise 3 : Toy Plastic Part (120min) / All sectors


Shape Design & StylingSolutions RTR: Real Time Rendering

EDU-CAT-E-RTR-FCourse Code EDU-CAT-E-RTR-FCATIA V5R15Brand & Release CATIA V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-RTR-FI-V5R15 Foils: EDU-CAT-E-RTR-FF-V5R15 Exercises: EDU-CAT-E-RTR-FX-V5R15

ObjectivesIn this course, you will learn how to interactively create realistic and dynamicrenderings



Content- Environment management- Camera management- Light sources management- DMU integration- Textures management- Stickers management- Animation: Turntable management- Animation: Animating scene elements

What is new in this releaseNew SettingsMulti-view modeCamera lens and toolbarLight toolbarDMU Integration chapter (DMU review, DMU presentation)New catalog of materials

ExercisesEx. 1: Defining an Environment (5min) / AutomotiveEx. 2: Defining the Camera (10min) / All sectorsEx. 3: Defining the Light Source (10min) / AutomotiveEx. 4: Applying Texture (40min) / AutomotiveEx. 5: Applying Stickers (10min) / AutomotiveEx. 6: Creating an Animation Using a Turntable (15min) / AutomotiveEx. 7: Creating an Animation of Scene (15min) / Automotive


Digital Mock-Up Course Material

Digital Mock-Up Solutions


Digital Mock-UpSolutions ANR: DMU Engineering Analysis Review

EDU-DMU-E-ANR-FCourse Code EDU-DMU-E-ANR-FDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.1 dayDuration 0.1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-ANR-FI-V5R15 Foils: EDU-DMU-E-ANR-FF-V5R15 Exercises: EDU-DMU-E-ANR-FX-V5R15 Detailed Steps: EDU-DMU-E-ANR-FS-V5R15

ObjectivesAttendees will learn how to manage V5 CATAnalysis files in DMU, and use it’stools on deformed shapes.

Participants' ProfileDesigners (P2 users only)

PrerequisitesDMB-F: Digital Mock Up BasicsDMN-F: Digital Mock Up NavigatorSPA-F: Digital Mock Space Analysis

Content- Quick Start- Generating Results- Managing Results

ExercisesEx. 1: Generate Results (5min) / All sectorsEx. 2: Animate Image (15min) / All sectors


Digital Mock-UpSolutions DMB: Digital Mock Up Basics

EDU-DMU-E-DMB-FCourse Code EDU-DMU-E-DMB-FDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMB-FI-V5R15 Foils: EDU-DMU-E-DMB-FF-V5R15 Exercises: EDU-DMU-E-DMB-FX-V5R15

ObjectivesUpon completion of the course, you will be conversant with the capabilities ofthe various workbenches in Digital Mock-Up (DMU). You will have mastered allthe Fundamental tasks of working with your Mock-Up. This will lay thefoundation to work efficiently with other dedicated workbenches to performmore specific and complicated tasks.

Participants' ProfileCatia and All DMU Users


Content- Introduction to DMU- Preparing the Session- Editing Components- Navigating through Components- Managing Viewpoints- Basic Measuring- Annotating

What is new in this releasePractice made on the DS Business-Jet

NotesMaster Exercise based on the DS Business-Jet

ExercisesEx. 1: DS Business Jet : Customizing your session (5min) / All sectorsEx. 2: DS Business Jet : Editing Components (20min) / All sectorsEx. 3: DS Business Jet : Navigating Through Components (5min) / All sectorsEx. 4: DS Business Jet : Navigation (5min) / All sectorsEx. 5: DS Business Jet : Managing Viewpoints (15min) / All sectorsEx. 6: DS Business Jet : Measuring (15min) / All sectorsEx. 7: DS Business Jet : Annotating (15min) / All sectors


Digital Mock-UpSolutions DMB: Digital Mock Up Basics V5R15 Update

EDU-DMU-E-DMB-UCourse Code EDU-DMU-E-DMB-UDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.1 dayDuration 0.1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMB-UI-V5R15 Foils: EDU-DMU-E-DMB-UF-V5R15

ObjectivesTo make you conversant with the enhancements of common functionalities inDMU V5R15

Participants' ProfileDMU Users

PrerequisitesDMU V5R14

Content- Overlay Settings

ExercisesEx. 1: Overlay Settings (10min) / All sectors


Digital Mock-UpSolutions DMN: Digital Mock Up Navigator

EDU-DMU-E-DMN-FCourse Code EDU-DMU-E-DMN-FDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMN-FI-V5R15 Foils: EDU-DMU-E-DMN-FF-V5R15 Exercises: EDU-DMU-E-DMN-FX-V5R15

ObjectivesIn this course, you will learn how to manipulate a Digital Mock-Up in reviewcontext, and make films to create review presentations.

Participants' ProfileDesigners, Managers

PrerequisitesDMU Basics

Content- Introduction to DMU Navigator- Managing Components- Managing Simulations- Managing Video Animations- Managing Scenes- Managing and Presenting Applicative Data- Managing 2D Documents

What is new in this releaseSome practices made on the Skateboard data

NotesMaster Exercise based on the DS Business-Jet

ExercisesEx. 1: DS Business-Jet : Managing Components (10min) / All sectorsEx. 2: DS Business-Jet : Creating Simulations (20min) / All sectorsEx. 3: DS Business-Jet : Generating Video Animations (15min) / All sectorsEx. 4: DS Business-Jet : Creating and Editing Enhanced Scenes (15min) / AllsectorsEx. 5: DS Business-Jet : Managing DMU Presentations (10min) / All sectors


Digital Mock-UpSolutions DMN: Digital Mock Up Navigator V5R15 Update

EDU-DMU-E-DMN-UCourse Code EDU-DMU-E-DMN-UDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.2 dayDuration 0.2 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMN-UI-V5R15 Foils: EDU-DMU-E-DMN-UF-V5R15

ObjectivesTo make you conversant with the enhancements of DMU Navigator Workbenchin V5R15

Participants' ProfileAll DMU Users

PrerequisitesDMU V5R14

Content- Managing Enhanced Scenes- Snapping Objects- Reordering Applicative Data

ExercisesEx. 1: Managing Overload Attributes (10min) / All sectorsEx. 2: Manage Scenes (5min) / All sectorsEx. 3: Snap Objects (5min) / All sectors


Digital Mock-UpSolutions DMO: Digital Mock Up Optimizer

EDU-DMU-E-DMO-FCourse Code EDU-DMU-E-DMO-FDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMO-FI-V5R15 Foils: EDU-DMU-E-DMO-FF-V5R15 Exercises: EDU-DMU-E-DMO-FX-V5R15 Detailed Steps: EDU-DMU-E-DMO-FS-V5R15

ObjectivesUpon completion of the course, you will be able to improve the productivity, bycomputing an optimized geometrical representation of data for mockupverification in the context of collaborative design review environment.


PrerequisitesDMB-F: Digital Mock Up BasicsSPA-F: Digital Mock Space Analysis

Content- Optimizer Quick Start- About Alternate Shapes- Generate alternate Shapes

ExercisesEx. 1: Computing a Simplification (10min) / All sectorsEx. 2: Define a Silhouette (10min) / All sectorsEx. 3: Define a Wrapping (10min) / All sectorsEx. 4: Define a Thickness (10min) / All sectorsEx. 5: Define an Offset (10min) / All sectorsEx. 6: Define Swept and Vibration Volumes (15min) / All sectorsEx. 7: Computing Free Space (5min) / All sectorsEx. 8: Computing a 3D Cut (10min) / All sectors


Digital Mock-UpSolutions FIT: Digital Mock-Up Fitting Simulator

EDU-DMU-E-FIT-FCourse Code EDU-DMU-E-FIT-FDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-FIT-FI-V5R15 Foils: EDU-DMU-E-FIT-FF-V5R15 Exercises: EDU-DMU-E-FIT-FX-V5R15 Detailed Steps: EDU-DMU-E-FIT-FS-V5R15

ObjectivesUpon completion of this course you will be able to define optimized methods formounting and un-mounting parts to form or dismantle an assembly.


PrerequisitesDMB-F: Digital Mock Up BasicsDMN-F: Digital Mock Up Navigator

Content- Fitting Customization- Managing Actions- Managing Fitting Simulations- Using Specific Tools

ExercisesEx. 1: Car Suspension – Play the Ready-To-Use replay (5min) / AutomotiveEx. 2: Car Suspension – Manage Actions (10min) / AutomotiveEx. 3: Car Suspension – Manage Sequences (10min) / AutomotiveEx. 4: Car Suspension – Compute Swept Volume (5min) / Automotive


Digital Mock-UpSolutions KIN: Digital Mock-Up Kinematics Simulator

EDU-DMU-E-KIN-FCourse Code EDU-DMU-E-KIN-FDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R151 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-KIN-FI-V5R15 Foils: EDU-DMU-E-KIN-FF-V5R15 Exercises: EDU-DMU-E-KIN-FX-V5R15 Detailed Steps: EDU-DMU-E-KIN-FS-V5R15

ObjectivesIn this course you will learn to define, simulate, analyze and ultimately designmechanisms using the ‘DMU Kinematics’ Workbench.


PrerequisitesDMB-F: Digital Mock Up Basics

Content- Create Joints and MechanismsDMU Kinematics an Overview- Defining a Mechanism * General Process to Define Mechanisms * Creating Joints * Joints Using Assembly Constraints * How to create a Revolute Joint * Joints using Topological or Geometric elements- Simulating Mechanisms- Analyzing Movements- Recording and Playing Simulations- Miscellaneous Functionalities

ExercisesEx. 1: Plane – Step1: Create a Mechanism (15min) / All sectorsEx. 2: Plane – Step2: Convert Assembly Constraints (15min) / All sectorsEx. 3: Plane – Step3 : Simulate the Mechanism (10min) / All sectorsEx. 4: Plane – Step4: Create an Animation (15min) / All sectorsEx. 5: Plane – Step5: Compute Swept Volume and Trace (15min) / All sectors

CATIA V5R15 Course Material Catalog May 26, 2005

Digital Mock-UpSolutions SPA: Digital Mock Space Analysis

EDU-DMU-E-SPA-FCourse Code EDU-DMU-E-SPA-FDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.1 dayDuration 0.1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-DMU-E-SPA-FI-V5R15 Foils: EDU-DMU-E-SPA-FF-V5R15 Exercises: EDU-DMU-E-SPA-FX-V5R15

ObjectivesThis course will teach populations involved in digital mock-up review of all sizesand product packaging processes, how to validate designs all along theproduct life cycle (from the design in context to the maintenance review), byensuring a better understanding of the problems for quick solving.

Participants' ProfileDesigners, Managers

PrerequisitesDMB-F: Digital Mock Up Basics

Content- Introduction to DMU Space Analysis- Measuring- Sectioning- Analyzing Interferences- Comparing Products

What is new in this releaseNew data for Master Exercise

NotesMaster Exercise now based on a Hand-Drill

ExercisesEx. 1: Measuring Distances (10min) / All sectorsEx. 2: Sectioning (20min) / All sectorsEx. 3: Analyzing Interferences (15min) / All sectors


Digital Mock-UpSolutions SPA: Digital Mock Space Analysis V5R15

UpdateEDU-DMU-E-SPA-UCourse Code EDU-DMU-E-SPA-UDigital Mock-Up V5R15Brand & Release Digital Mock-Up V5R150.1 dayDuration 0.1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-DMU-E-SPA-UI-V5R15 Foils: EDU-DMU-E-SPA-UF-V5R15

ObjectivesIn this course you will learn about the new tools and the enhancements in DMUSpace Analysis V5R15 workbench

Participants' ProfileMechanical Designers, DMU Users

PrerequisitesDMU Space Analysis V5R14

Content- Enhancements in Measure Tools

ExercisesEx. 1: Measure Tools (10min) / All sectors


Date post:	09-Mar-2015
Category:	Documents
Upload:	ibnuseid
View:	289 times
Download:	24 times