12
Cylinder Valves
Cylinder Valves - Small Cylinders With OPD
G-1855-A02 Black Handle for BBQ GrillsThermally sensitive. Built-in excess flow.Use for appliances up to 70,000 BTU/HR.
Fill AdapterQCC X FPOL
7193T-10
Fill AdapterQCC X 1/4” MNPT
7193U-10
Regulator ConnectorM Quick Conn X 1/4” MNPT
Fill AdapterM Quick Conn X FPOL
5LPA
These OPD valves are designated for very specific dip tube lengths as shown in the table. Check the “D.T.” data stamped on the cylinder to determine the correct dip tube length required.
PartNumber
Dip TubeLength With
DeflectorContainer
Connection
Service Connection PressureRelief
Valve Setting
Accessories
Type DescriptionACME Dust
Cap
80-9890 3.0”
3/4” MNGT Type I1-5/16”
M ACME andFPOL
375 PSIG907-12Order
Separately
80-8107 4.0”
80-8109 4.8”
80-8110 6.5”
QCC Cap
80-8107
Type I QCC ACME Adapters
Type II Quick Connect Adapters
5LPA-8C
G-1855-A03 Green Handle for larger appliancesThermally sensitive. Built-in excess flow.Use for appliances 71,000 - 200,000 BTU/HR.
G-1855-A02
CGA 791 Standard
CGA 810 Standard
ME-519-25H Red Handle w/1/4” Hose BarbThermally sensitive. Built-in excess flow.Use for appliances 71,000 - 400,000 BTU/HR.
ME-519-25H
907-12
Male QCC AdapterQCC X 1/4”FNPT
ME393-1
13
Heavy Duty Cylinder Valve - Vapor Service
Cylinder Valves
9103D11.6Cylinder Valve for RV - Vapor Service
PartNumber
ContainerConnection
ServiceConnection
PressureRelief
Valve Setting
FlowCapacity
SCFM/Air
9106CO 3/4” MNGT FPOL 312 PSIG 6459106CO
Cylinder Valves - Liquid Withdrawal
PartNumber
ContainerConnection
LiquidService
Connection
VaporService
Connection
Dip TubeLength With
Deflector
LiquidWithdrawalTube Length
LiquidLP-Gas
Closing Flow
PressureRelief
Valve Setting
9107K8A3/4” MNGT
CGA 555 None 11.6 44” 1.7 GPM375 PSIG
8556 CGA 555 FPOL None 44” 2.3 GPM
9107K8A 8556
Female POLOutlet forVapor Service
CGA 555Outlet forLiquid Service
CGA 555Outlet forLiquid Service
12982Liquid Outlet AdapterCGA 555 X 1/4” MNPT
Vapor Outlet AdapterMPOL X 1/4” MNPT
970
PartNumber
ContainerConnection
ServiceConnection
PressureRelief
Valve Setting
Dip TubeLength With
Deflector
9103D11.6 3/4” MNGT FPOL 375 PSIG 11.6”
This heavy duty cylinder valve is designed for vapor withdrawal of DOT cylinders up to 100 lbs. propane capacity.
Designed for vapor withdrawal service on permanantly mounted RV tanks. Valve has a large capacity relief set at 312 PSIG.
Designed for liquid withdrawal service in industrial applications on cylinders up to 100 lbs. propane capacity.
14
Cylinder Valves
Cylinder Valves - Vapor Service - No ReliefChoose either Standard or MultiBonnet versions. Valves have no integral relief valve and may only be used on containers that have an independent pressure relief valve.
9101C1 9101R1
Standard Bonnet MultiBonnet
Service Valves for Motor Fuel - EFV - No Relief
PartNumber
ContainerConnection
ServiceConnection
Liquid TubeConnection
LiquidLP-Gas
Closing Flow
901C5
3/4” MNGT
FPOLNone
2.6 GPM
9101H5 3/8” SAEFlare
3.6 GPM
9101H6 1/4” NPT 2.6 GPM
9101Y5H60O Angle3/8” SAE
FlareNone 3.6 GPM 9101H5 9101Y5H
Service Valves for DOT Forklift Cylinders
9101P6
9101P5H
7141M 7141F
7141M-3R Flat Gasket
7513-25 Oring
PartNumber
ContainerConnection
ServiceConnection
Liquid TubeConnection
LiquidLP-Gas
Closing Flow
9101P5H3/4” MNGT 3/8 MNPT
None 2.6 GPM
9101P6 1/4” NPT 1.5 GPM
PartNumber
BonnetStyle
ContainerConnection
ServiceConnection
Dip TubeLength With
Deflector
9101C1Standard
3/4” MNGT FPOL
None
9101D11.1 11.1”
9101R1MultiBonnet
None
9101R11.1 11.1”
Designed specifically for vapor or liquid withdrawal service on ASME motor fuel containers.
Designed specifically for vapor or liquid withdrawal service on DOT forklift containers.
Accessory Lift Truck Check Connectors
15
Multivalves
Multivalves For DOT & ASME - Vapor Service
PartNumber
BonnetStyle
ContainerConnection
ServiceConnection
FillingConnection
Dip TubeLength With
Deflector
LiquidWithdrawalTube Length
LiquidLP-Gas
Closing Flow
PressureRelief
Valve Setting
8555DL11.6 Standard 3/4” MNGT CGA 555 1-3/4” Male Acme 11.6” 44” 1.7 GPM 375 PSIG
Multivalve For DOT - Liquid Service
* DOT valves have relief settings of 375 PSIG. Max container capacity is based on propane capacity. ASME valves have relief settings of 250 PSIG. Max container capacity is based on outside surface area.
8555D11.6
6543R11.1
8555DL11.6
Large Capacity Relief
CGA 555Outlet forLiquid ServiceFemale POL
Outlet forVapor Service
PartNumber
BonnetStyle
ContainerConnection
ServiceConnection
FillingConnection
Dip TubeLength With
Deflector
Max*Container
SizeContainer
Type
PressureRelief
Valve Setting
8555D11.6 Standard
3/4” MNGT
FPOL 1-3/4” Male Acme
11.6” 200 lbs. DOT 375 PSIG8555R11.6 MultiBonnet
6532R12.0 MultiBonnet 12.0” 43 sq. ft. ASME 250 PSIG
6533R11.7 MultiBonnet 11.7” 420 lbs. DOT 375 PSIG
6542R12.0 MultiBonnet1” MNGT
12.0” 53 sq. ft. ASME 250 PSIG
6543R11.1 MultiBonnet 11.1” 420 lbs. DOT 375 PSIG
Designed for vapor withdrawal service from ASME and DOT containers. They allow on-site cylinder filling without interrupting gas service.
Designed for liquid withdrawal service from DOT containers up to 100 lbs. propane capacity. It allows on-site cylinder filling into the vapor space without interrupting gas service.
16
Multivalves
Multivalves For ASME Single Opening Containers
Multivalves For Vapor Withdrawal
PartNumber
ContainerConnection
ServiceConnection
FillingConnection
VaporEqualizing
DipTube
Length
8593AR16.0 1-1/2”MNPT
FPOL
1-3/4”Male ACME
1-1/4”Male ACME
With4200 CFH
EFV
30”
7556R12.0 3/4” MNGT None 12.0”
7556
8593
G8475RW
PartNumber
ContainerConnection
ServiceConnection
FillingConnection
VaporEqualizing
FloatGauge
Opening
DipTube
Length
PressureRelief
Valve Setting
*MaxContainer
Size
G8475RV
2-1/2”FNPT FPOL 1-3/4”
Male ACME
1-1/4”Male ACME
With4200 CFH
EFV
Fits“JUNIOR”
Size30” 250 PSIG
83 sq .ft. Aboveground
276 sq. ft. Underground
G8475RW192 sq. ft. Aboveground
639 sq .ft. Underground
These Multivalves are designed for use in single opening ASME containers equipped with a 2-1/2” MNPT riser for either under-ground or aboveground service. Two models are offered. Select the model with the correct relief valve size to match the required flow rate for the container being serviced.
These Multivalves provide vapor service for ASME containers in a compact design with multi-function components.
* Tank size reference: A 500 gallon tank has 98 sq. ft. surface area. A 1000 gallon tank has 174 sq. ft. surface area.
17
Heavy Duty Globe And Angle Valves
Shutoffs
RegO Globe and Angle bodies are made from rugged ductile iron. Spring loaded teflon packing provides exceptional leak-free service. Positive shutoff is provided by the synthetic rubber swivel style seat disc. All the valves incorporate a plugged 1/4” FNPT boss on the downstream side of the body for attaching either a hydrostatic relief or a vent valve.
A7518AP
A7507AP
A7509BP
Compact Globe And Angle Valves
Part Number Inlet andOutlet
ConnectionBonnet
MaterialGlobe Angle
7704P 7704LP1/2” FNPT
Brass
A7704P A7704LP Steel
7705P 7706P3/4” FNPT
Brass
A7705P A7706P Steel
Lighter pattern valve with flange seal stem packing. Valves incorporate a plugged 1/4” FNPT boss on the downstream side of the body for attaching either a hydrostatic relief or a vent valve.
7705P7706P
Quick Acting ValvesDesigned to provide instant shut-off and fast opening. Vent valve included on downstream side of the body. Locking handle on “L” series valves prevents accidental opening of valve.
PartNumber
Inlet andOutlet
ConnectionLockingHandle
7554SAV1/2” FNPT
No
7554LAV Yes
7554SV3/4” FNPT
No
7554LV Yes
A7707L 1” FNPT (Straight)Yes
A7708L 1” FNPT (Angle)7554LV7554SV
Part Number Inlet andOutlet
Connection
Propane Flow (GPM)at 1 PSIG Pressure Drop
Globe Angle Globe Angle
A7505AP A7506AP 3/4” FNPT 12.0 17.7
A7507AP A7508AP 1” FNPT 17.8 22.0
A7509BP A7510BP 1-1/4” FNPT 36.5 54.0
A7511AP A7512AP 1-1/2” FNPT 43.0 55.5
A7511FP ----- 1-1/2” Flanged 46.0 -----
A7513AP A7514AP 2” FNPT 75.0 88.5
A7513FP A7514FP 2” Flanged 78.0 133.0
A7517AP A7518AP 3” FNPT197.0 303.0
A7517FP A7518FP 3” Flanged
A7708L
18
Quick Acting Minimum Loss Hose-End Valves
Shutoffs
Quick Acting Cylinder Charging Valves
PartNumber
InletConnection
OutletConnection
7901T 1/4” FNPT 1/4” FNPT
7901TA 3/8” FNPT 3/8” FNPT
7901TB1/2” FNPT
1/4” FNPT
7901TC 1/2” FNPT
Brass body with compact design for cylinder charging.
7901TB
PartNumber
InletConnection
OutletConnection
Flow at1 PSIG Drop
A7797A 1” FNPT 1-3/4”F ACME 16.0 GPM
Instant shutoff and fast opening with the valve seat located in the bottom of the extended ACME connector. Thumb latch on handle prevents accidental opening. Spring loaded chevron packing gives superior leak free service.
A7797A
Minimum LossValve Seat
Hose-End SwivelsRugged leak free design allows complete 360O rotation of hose end valves for easy connections to fillers. Es-pecially helpful with stiff hoses in the cold of winter.
ME850SS-6 3/4” SwivelME850SS-8 1” Swivel
Typical Swivel Application
A7797A in Bobtail Delivery Application
Spring-loaded ThumbButton Opens Latch
Handle Pivots toFull Open Position
PRESS
Cylinder Filling Connectors
7193D-10 POL
7193L-10A Lift Truck
7193U-10 QCC
7193T-10 FPOL X QCC
12982 & 5760AFPOL X F Liquid
19
Hotplate Valve
Shutoffs
Liquid Transfer ValvesPrimarily used in conjunction with ChekLok adapters to transfer liquid from bulk storage tanks through the tank mounted ChekLok excess flow valves. 1/4” side tap provided for hydrostatic relief valve.
7550P
Liquid Transfer Diagram
New Style ChekLok Old Style ChekLok
7590U-10 7572C-14A
7590U - 3/4” Tank Connection7591U - 1 1/4” Tank Connection
The old style ChekLok valvesare obsolete. Use new style.
PartNumber
BonnetMaterial
InletConnection
OutletConnection
LiquidLP-Gas
Closing Flow
7550P Brass
3/4” MNPT
3/4” FNPT
NoneA7550P Steel
7550PX Brass16.0 GPM
A7550PX Steel
7551P Brass1/2” FNPT None
A7551P Steel
Needle Valves
PartNumber
InletConnection
OutletConnection
1224WA 1/4” MNPT 1/4” MNPT
25NVBR 1/4” FNPT 1/4” FNPT
NV108-4 1/4” MNPT 1/4” FNPT
1316WA 9/16” -18 LH 1/4” MNPT
1318WA 1/4” MNPT 9/16” -18 LH
Used for accurate throttling in torch and small burner applications and pressure gauge valves.
1316WA
25NVBR
NV108-4
CCC 52-1065
Part Number Inlet Outlet
314 1/8” MNPT Hood Orifice
Porcelain handle gas cock with hood orifice.
20
C
Shutoffs
Multipurpose Valves With Filler Connection
PartNumber
InletConnection
OutletConnection
FillingConnection
LiquidLP-Gas
Closing Flow
A8016DP1-1/4” MNPT
None 1-3/4” M ACME
44 GPM
A8018DP 1” FNPT 50 GPM
Multipurpose Valves Liquid Withdrawal
PartNumber
InletConnection
OutletConnection
LiquidLP-Gas
Closing Flow
A8017DP
1-1/4” MNPT
1” FNPT 55 GPM
A8017DLP 3/4” FNPT 49 GPM
A8017DH*1” FNPT
49 GPM
A8020D 78 GPM
* A8017DH has special back pressure check valve in the shutoff seat which allows trapped product in the downstream piping to return to the storage tank.
A8016DP
A8018DP
A8017DPA8020D
Apollo Bronze Ball Valves
80 Series
77 Series
Part NumberInlet And
OutletConnection
Length Through Valve “C”
Standard Port Full Port 80 Series 77 Series
80-101-01 77-101-01 1/4” FNPT2.06”
2.25”80-102-01 77-102-01 3/8” FNPT
80-103-01 77-103-01 1/2” FNPT 2.25”
80-104-01 77-104-01 3/4” FNPT 3.00” 3.12”
80-105-01 77-105-01 1” FNPT 3.37” 3.62”
80-106-01 77-106-01 1-1/4” FNPT 4.00” 4.25”
80-107-01 77-107-01 1-1/2” FNPT 4.37” 4.75”
80-108-01 77-108-01 2” FNPT 4.68” 5.37”
80-109-01 77-109-01 2-1/2” FNPT 6.50” 6.50”
80-100-01 ----- 3” FNPT 6.75” -----
Designed specifically for use as a manual filler for anhydrous ammonia applicator containers. Manual valve must be fully open and back seated for the excess flow to be effective.
Designed specifically for liquid withdrawal for LP Gas and anhydrous ammonia containers.
Bronze, threaded 600 W.O.G. ball valves. Both series feature RPTFE seats and stem seals, adjustable packing glands and blow-out-proof stem seal design.
21
Red Cap Pipe X Pipe Ball Valves
Part Number Inlet andOutlet
Connection
Max RatingAGA
Standard With Side Tap
R602 3/8 ----- 3/8” 2 PSIG
R602 1/2 R602S 1/2 1/2” 2 PSIG
R602 3/4 R602S 3/4 3/4” 2 PSIG
Red Cap Flare X Flare Ball Valves
Part Number Inlet andOutlet
Connection
Max RatingAGA
Standard With Side Tap
R602 FF 66 R602S FF 66 3/8” 2 PSIG
R602 FF 88 R602S FF 88 1/2” 2 PSIG
R602 FF 1010 ----- 5/8” 2 PSIG
Red Cap Flare X Pipe Ball Valves
R602 R602S
R602FF
R602FM
R602FP
The R602 and R602S gas ball valves are designed specifically for gas service. They incorporate forged brass bodies for additional strength, hard chrome plated balls, teflon seats and Dacromet treated handles.
AGA CertificationThe R602 & R602S valves have been tested to comply with the AGA 3.88 standard. This standard covers manually operated gas valves for use in House Piping Systems. Pressures up to 5 PSIG.The R602 & R602S valves have been AGA certified tested to ANSI Z.21-15 standard. This standard covers manually operated gas valves for use as Appliance Shutoffs. Pressure at 1/2 PSIG.
UL ListingsThe R602 & R602S (1/2” & 3/4” sizes only) are UL listed under YRPV.MH15525. This category covers manual gas shut-off valves intended for use in lines conveying fuel gas. Maximum working pressure 200 PSIG.
Part Number InletFlare
Connection
OutletPipe
Connection
Max RatingAGA
Flare X MNPT Flare X FNPT
R602 FM 68 R602 FP 68 3/8” 1/2” 2 PSIG
R602 FM 88 R602 FP 88 1/2” 1/2” 2 PSIG
----- R602 FP 1012 5/8” 3/4” 2 PSIG
Shutoffs
Red Cap Gas Ball Valves
22
Typical Three Way Applications
Dispensing systemsIsolating meter flow from cylinder flow
Cylinder purgingCycling between purge and discharge
FromPump
ToCyl.Fill
ToBulkFill
70-601-01 1/4” Bronze Side Entry70-604-01 3/4” Bronze Side EntryBronze, threaded, 400 W.O.G.Sizes through 2” available by special order
Shutoffs
Three Way Mixing Ball ValvesMixing valves are side entry valves in relation to the plane of ball rotation. As such, they only require a 90O rotation of the handle to change discharge ports. Both discharge ports are open between handle positions.
Plugaroo Combination Plug and Check Valves175# working pressure plug valves with integral check. Well suited for mixer instal-lations. Available in FNPT or 125# flanged versions.
PartNumber
Inlet andOutlet
Connection
EndTo
End
173 2” 2” Screwed 6 1/2”
173 3” 3” Screwed 8 1/4”
173 4” 4” Screwed 9 3/4”
175 2” 2” Flanged 7”
175 3” 3” Flanged 8”
175 4” 4” Flanged 9”
175 6” 6” Flanged 10”
173 2”
175 Cutaway
Open Position Closed Position
70-604-01
23
Bulk Storage Plants
The graphic shows the layout of a typical propane bulk plant. The main functions of storage, transport fill and bobtail load-ing are depicted. Although each existing bulk plant is unique in their physical layouts, the basic installations are all similar in providing the functions described.
The components on the following pages of this catalog make up the basis for a complete operative bulk plant.
2
1
3
20
21
4
5
5
5
6
6
67
9
8
10
22
23
15
11
12
1817
13
14
3" Liquid
1-1/4" Vapor
3" Liquid
16
19BobtailLoading
Riser
TransportRiser
Pumpset
Typical Bulk Plant
Major ComponentsKey
123456789101112
Key1314151617181920212223
Description3” Internal Valve2” Internal Valve1-1/4” Internal ValveBack CheckExcess Flow ValveEmergency Shutoff3” Angle Valve1-1/4” Angle Valve3-1/4” MAcme w/Cap2-1/4” MAcme w/Cap1-1/4” Globe Valve2” Globe Valve
Description2-1/4” FAcme w/Plug3-1/4” FAcme w/Plug3” Pump2” BypassHydrostatic ReliefPressure Gauge3” StrainerThermometerFloat GaugePressure GaugeRelief Valve w/Stack
24
Large Container Mounting
Underground Tank Mounting
Expansion Material
Large propane storage containers must be mounted on concrete piers. Typical mounting is depicted. Steel supports may only be 6” high unless fireproofed.
The pier footing must be below frost line. A 4 foot height from grade to the bottom of the tank is desirable to facilitate tank valves, piping and especially pump suction elevation.
A 3/4” sheet of expansion material is placed between the tank and the concrete both as a cushion for irregularities and as an isolation for corrosion protection.
Underground tank installations require anchorage with a concrete footing of sufficient weight to prevent flotation. A typical anchorage system is shown.
Components sized per tank size. Call for details.
3/4” X 15” X 5ft.(2 pieces per pier)
Bulk Storage Plants
ExpansionMaterialDetail
Tank
Concrete
Anchor Eye Turnbuckle
Wire Rope
ThimbleCrosby Clip
ExpansionMaterial
25
Large Container Connections
Connections for Containers over 4000 Gallons
Connection Illustrations
The container connection requirements as specified in NFPA 58 for containers over 4000 gallons water capacity are listed below. The “spirit” of the requirements is to provide remote closure and automatic (fire) closure AT THE CONTAINER CONNECTIONS. The requirements are effective July 1, 2011.
ServiceAfter Year 2001
InstallationsBefore Year 2001
Installations
Vapor InletOption A orOption B or
Option C
Norequirement
Vapor Outlet Option B orOption C
Norequirement
Liquid Inlet Option D orOption E
Option D orOption E orOption F orOption G
Liquid Outlet Option EOption E
orOption H
Permissible Options for Connections
Positive Shutoff &Check Valve
Option A Option B Option C
Option E
Option F (liquid in)and
Option H (liquid out)
Option D
Option G
Positive Shutoff &Check ValvePositive Shutoff &
Excess Flow Valve
Positive Shutoff &Excess Flow Valve &Check Valve
Internal Valve
Internal Valve
Excess Flow Valve & API 607 Ball Valve
Excess Flow Valve & API 607 Ball Valve Positive Shutoff & Excess Valve &
Emergency Shutoff
OR
OR
26
Plant Closure Systems
Pneumatic remote closure is the preferred method for internal valve actuation. The pneumatic actuator attaches directly to the internal valve body and strokes the valve open and closed. This arrangement offers several distinct advantages:
• The tank valves remain normally closed and are only opened during transfer opera-tions.• The pneumatic controls can be installed at any convenient location.• The emergency shut off valves at the loading and unloading risers can be incor-porated into the plant pneumatic system.• The plant operator actuates only one con-trol from a central, convenient location.
For plants with basic systems such as a single storage tank, remote closure can be accomplished readily with cabling. The internal valves are controlled separately from the emergency valves on the risers. Possible cabling arrangements are de-picted below.
Pneumatic Control
Cable Control
Internal Valve Control
Emergency Valve Control
Two internal valves with remote closure controlled by a single taut wire cable.Pulling the cable anywhere along its length will trigger both valve release latches.
A single emergency shutoff valve with remote closure controlled by a taut wire cable.Pulling the cable anywhere along its length will trigger the valve release mechanism.
27
Internal Valves
Internal Valve Overview
Internal Valve Installation Note
Valvein
FullCoupling
Valvein
HalfCoupling
Valve in Standpipeor
Pipeline
Valve Fully ClosedInlet pressure and the closing spring pro-vides “bubble-tight” closure.
Valve Fully OpenAfter pressure equalization, the handle is moved to the full open position and the excess flow spring holds the main valve wide open.
Excess Flow ClosedA large pressure drop across the valve moves the main seat to the closed position. A slow bleed occurs through the fully open pilot seat.
Rapid BleedThe handle is moved to the mid-point position providing rapid bleed past the partially open pilot seat.
The handle does not open the main seat of the valve. The handle only lifts the pilot stem allowing product to bleed down-stream of the main seat. After the pressure equalizes across the main seat, the valve spring opens the valve fully. A pressure drop in the downstream piping, such as in a pipe breakage, causes the higher inlet pressure to close the main seat.
Internal valves are used primarily in the openings of storage tanks. With their normally closed design and shutoff seat inter-nal to the storage tank, these valves provide a very safe primary shutoff at the container opening. The valves are supplied with a handle for manual operation. Accessories allow them to be actuated manually, by cable or with air.
Internal Valves should be installed in half couplings. Full couplings, standpipes and standard size pipelines create undue restriction to the flow around the valve seat. Premature excess flow closure and extreme pressure drops will occur when installed in other than half couplings.
When installing Internal Valves in standpipes or pipelines, follow these recommended configurations closely to avoid problems.
Recommended Configuration
ValveA
Pipe SizeB
ReducerC
Length
A3209 Series(1-1/4” MNPT) 2” 2” X 1-1/4” 8”
A3212 Series(2” MNPT) 3” 3” X 2” 12”
A3213 Series(3” MNPT) 5” 5” X 3” 14”
Valve Operation
Rapid BleedFull Flow
Slow Bleed
CA
B
28
Internal Valves
1-1/4” Threaded Internal Valves
1-1/4” Application Examples
A3209D050
A3209TL
A3209PAA3209DT050
A3209D with Pneumatic Actuator usedon Vapor Return of Bobtail
A3209D used on Liquid Feed to Pump (cable or pneumatic actuation)
A3209D050with A3209TL
A3209D050with A3209PAF
Designed for use as the main valve on small capacity pumping systems, the vapor equalizing opening on bobtail trucks or on inline installations.
PartNumber Inlet
ConnectionOutlet
Connection
Closing Flow Accessories
LP-Gas NH3Thermal
LatchPneumaticActuator
A3209D050
1-1/4” MNPT 1-1/4” FNPT
50 GPM 45 GPM
A3209TL
A3209PAor
A3209PAF(1/4” FNPT)
A3209D080 80 GPM 72 GPM
A3209DT050 65 GPM 45 GPM
A3209DT080 80 GPM 72 GPM
4”
1.5”
2.9”
29
Internal Valves
2” & 3” Threaded Internal ValvesDesigned for liquid withdrawal and vapor equalizing on bobtail trucks, transports and stationary stor-age tanks. Valves may be operated manually or pneumatically.
A3212R
A3213TL
A3213PA
A3213TA3213R withA3213RA Rotary Actuator
A3212R in Tank Coupling
PartNumber(StandardValves)
PartNumber(“T” BodyValves)
InletConnec-
tionMNPT
OutletConnec-
tionFNPT
Closing Flow (GPM)
Half Coupling
Closing Flow (GPM)
Full Coupling
Accessories
RotaryPneumaticActuator
PneumaticActuator
ThermalLatchLP-Gas NH3 LP-Gas NH3
A3212R105 A3212RT105
2” 2”
105 95 65 59
A3212RA
A3213PA(3/8” FNPT)
A3213TL
A3212R175 A3212RT175 175 158 100 90
A3212R250 A3212RT250 250 225 130 117
A3213R150 A3213RT150
3” 3”
150 135 125 113
A3213RAA3213R200 A3213RT200 200 180 160 144
A3213R300 A3213RT300 300 270 250 225
A3213R400 A3213RT400 400 360 325 293
30
Internal Valves
3” Flanged Internal Valves
Part Number OperatingLever
PositionInlet
ConnectionOutlet
Connection
Closing Flow (GPM)PneumaticActuatorSingle Flange Double Flange LP-Gas NH3
A3217AR160 A3217DAR160 Right Side
3” 300#ANSI RFModifiedFlange
3” 300#ANSI RF
Flange
160 145A3217ARPA
A3217AL160 A3217DAL160 Left Side A3217ALPA
A3217AR210 A3217DAR210 Right Side210 190
A3217ARPA
A3217AL210 A3217DAL210 Left Side A3217ALPA
A3217AR260 A3217DAR260 Right Side260 236
A3217ARPA
A3217AL260 A3217DAL260 Left Side A3217ALPA
A3217AR410 A3217DAR410 Right Side400 372
A3217ARPA
A3217AL410 A3217DAL410 Left Side A3217ALPA
A3217FPA
A3217Single Flange
A3217ARRight Hand
A3217DALDouble Flange
TypicalMounting
A3217 withA3217FPA
A3217ALLeft Hand
Designed for liquid withdrawal on bobtail trucks and transports. Valves may be operated manually or pneumatically.
A3200L
31
Internal Valves
A3219RTRemote Thermal Release
A3219RT ProvidingRemote Diagonal Closurewith Fusible Element
A3219FA600L
A3219FA600Lwith
4” Transport Pump
A3219FA600Lwith
A3219FPAPneumatic Operator
A3219FPAPneumatic Operator
4” Flanged Internal ValvesDesigned for liquid withdrawal on transports or large storage tanks. Valves may be operated manually or pneumatically.
Part NumberInlet
ConnectionOutlet
Connection
Closing Flow (GPM)PneumaticActuator
RemoteThermalReleaseLP-Gas NH3
A3219FA400L 4” 300#ANSI RFModifiedFlange
4” 300#ANSI RF
Flange
400 360
A3219FPA A3219RT
A3219FA600L 600 540
32
Internal Valves
Flomatic Pressure Actuated Internal ValvesDesigned for liquid withdrawal on bobtail trucks and transports. Valves are fully automatic opening and closing with pump discharge pressure.
Part NumberInlet
ConnectionOutlet
Connection
Accessories(Included With Flomatic) Pneumatic
ActuatorFilter 3-Way Valve
A7883FK
3” 300#ANSI RFModifiedFlange
3” 300#ANSI RF
Flange
A7884-201 A7853A A7853PA
A7884FK
4” 300#ANSI RFModifiedFlange
4” 300#ANSI RF
Flange A7883FK
A7853PA
A7853A
Flomatic Valve Closed Flomatic Valve Open
A7884-201
33
Loading And Unloading Risers
Transport Unloading Riser
2 Hole Riser 3 Hole Riser
Bobtail Loading Riser
Loading and unloading risers incorporate heavy steel frame and legs to protect plant piping in the event of a pull-away. Forged steel pipe couplings are welded in the vertical plane to accept plant and discharge piping. Discharge nipples as illus-trated below are recommended to provide extended leverage to ensure a reliable shear point. Units come completely welded and ready to set in place.
Fill
BackCheck
EmergencyShutoff
Vapor Return
Fill
EmergencyShutoffs
Vapor Return
Fitted with 3”, 2” or 1-1/4” Couplings Fitted with 3”, 2” or 1-1/4” Couplings
34
Emergency Shutoff ValvesFor installation in liquid and vapor transfer lines at bulk plants to provide for quick shutoff in the event of accidental pull-away, line breakage or hose rupture. Valves may be opened and closed by use of the operating lever, by remote cable control or by means of a pneumatic actuator. All arrangements incorporate a fusible element for fire emergency shutoff.
Emergency Shutoff Valves
PartNumber
In & OutConnection
LP-Gas Liquid FlowCapacity (GPM)
PneumaticShutdown
PneumaticOpen/Close
6010 1-1/4” FNPT 259
6016-60D 6016-60C6016 2” FNPT 711
6024 3” FNPT 13256016
6016 with6016-60C
6010 with6016-60D
Pull-Away ValvesProvides pull-away protection for transfer operations. Stops gas escape from both upstream and downstream lines in the event of a pull-away.
PartNumber
Inlet andOutlet
Connections
LengthOf
Valve
LP-Gas Flowat 10 PSIGDifferential
A2141A6L 3/4” FNPT 3-7/8” 16 GPM
A2141A8 1” FNPT 4-9/16” 30 GPM
A2141A10 1-1/4” FNPT 5-5/8” 75 GPM
A2141A16 2” FNPT 14-5/16” 350 GPM
A2141A6L A2141A8
Typical DispenserPull-Away
Typical Bulk FillPull-Away
35
Sight Flow IndicatorsAllows bulk plant operators to visually inspect liquid flow conditions. Integral swing check prevents reverse flow and product loss if the hose fails during a loading operation.
PartNumber
Inlet AndOutlet
Connections
LengthThrough
Valve
A7794 2” FNPT 5-3/4”
A7796 3” FNPT 7-3/8”
PartNumber
FitsOver
Pipe Size
MatchingEyebolt
B3198H-1-1/4 1-1/4” EYE-06-33/8” X 3”B3198H-2 2”
B3198H-3 3” EYE-08-41/2” X 4”
A7796
Emergency Shutoff Accessories
Valve Cabling Accessories
212 DegreeFusible Link
Pipe Clamps & Eyebolts
7605-74Sleeve
B3198H-2
EYE-06-3
7605-751/8” Crosby Clip
7606RM-1 1/16” SS Cable
7606RM-18 1/8” SS Cable
7605-73 1/16” Cable Sleeve
7605-74 1/8” Cable Sleeve
Stainless steel cable and accessories for remote control of internal valves and emergency shutoff valves.
36
Pneumatic Accessories
Pneumatic Tubing Accessories
1924-01-1FFNylon Tubing
1468X4X4 1/4” MNPT Adapter
1462X4Union
1464X4Union Tee
Nitrogen Regulator
Charging Valve
Latching Valve
Pneumatic control of internal valves and emergency shutoff valves.
222P-4-2Adapts 1/4” FNPT
To1/8” MNPT
Charging valves are spring return with “push to charge” action.
Control valves are diaphragm actuated for leak-free reliable service.
Latching valves are pilot actuated,latched open with system pressure.
3-way valves have plunger detents whichhold the valve in the On or Off positionuntil the operator manually moves the plunger.
1469X4X4Union Elbow
125T Charging Valve
Diaphragm Actuated Control Valves
125A Latching Valve
Rack MountedCharging Assembly
Post MountedDischarge Assembly
125V 3-way Valve
ToSystem
3-way Valve