ICS 23.040.10; 77.140.75

Welded steel tubes for pressure purposes – Technical delivery conditionsPart 1: Non-alloy steel tubes with specified room temperature properties

(includes Amendment A1:2005)English version of DIN EN 10217-1:2002 + A1:2005

Geschweißte Stahlrohre für Druckbeanspruchungen – Technische Lieferbedingungen – Teil 1: Rohre ausunlegierten Stählen mit festgelegten Eigenschaften bei Raumtemperatur (enthält Änderung A1:2005)

A comma is used as the decimal marker.

National forewordThis standard has been prepared by ECISS/TC 29 ‘Steel tubes and fittings for steel tubes’ (Secretariat: Italy).The responsible German body involved in its preparation was the Normenausschuss Eisen und Stahl (Steeland Iron Standards Committee), Technical Committee Rohre aus allgemeinen Baustählen oder Feinkornbau-stählen.DIN V 17006-100 is the standard corresponding to CEN Technical Report CR 10260 referred to in clause 2of the EN.

AmendmentsThis standard differs from the August 2002 edition in that more detailed specifications regarding inspectionhave been given and Annex ZA has been revised.

Previous editionsDIN 1626: 1952x-12, 1984-10; DIN 1626-1: 1965-01; DIN 1626-3: 1965-01; DIN 1626-4: 1965-01;DIN 1628: 1984-10; DIN EN 10217-1: 2002-08.

National Annex NAStandard referred to(and not included in Normative references and Bibliography)

DIN V 17006-100 Designation systems for steel – Additional symbols for steel names

DEUTSCHE NORM April 2005

DIN EN 10217-1 {

© No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut für Normung e.V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).

SupersedesAugust 2002 edition.

English price group 17www.din.de

www.beuth.de 9637698

Continued overleaf.Document comprises 39 pages.

06.05Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

English version

ICS 23.040.10; 77.140.75 Supersedes EN 10217-1:2002.

Welded steel tubes for pressure purposes –Technical delivery conditions

Part 1: Non-alloy steel tubes with specified room temperature properties(includes Amendment A1:2005)

© 2005. CEN – All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.

Ref. No. EN 10217-1:2002 + A1:2005 E

Geschweißte Stahlrohre für Druckbe-anspruchungen – Technische Liefer-bedingungen – Teil 1: Rohre ausunlegierten Stählen mit festgelegtenEigenschaften bei Raumtemperatur(enthält Änderung A1:2005)

This European Standard was approved by CEN on 2002-04-25 and AmendmentA1 on 2004-12-09.CEN members are bound to comply with the CEN/CENELEC Internal Regulationswhich stipulate the conditions for giving this European Standard the status of anational standard without any alteration.Up-to-date lists and bibliographical references concerning such national stand-ards may be obtained on application to the Management Centre or to anyCEN member.The European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibility of aCEN member into its own language and notified to the Management Centre hasthe same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, theCzech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands,Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, andthe United Kingdom.

Management Centre: 36, rue de Stassart, B-1050 Brussels

European Committee for StandardizationComité Européen de NormalisationEuropäisches Komitee für Normung

ÈÉË

Tubes soudés en acier pour servicesous pression – Conditions techni-ques de livraison – Partie 1: Tubes enacier non allié avec caractéristiquesspécifiées à température ambiante(amendement A1:2005 inclus)

EN 10217-1

January 2005+ A1May 2002

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 2EN 10217-1:2002 + A1:2005

ContentsPage

Foreword to EN 10217-1:2002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Foreword to EN 10217-1:2002/A1:2005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Terms and definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Classification and designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65.1 Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65.2 Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Information to be supplied by the purchaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66.1 Mandatory information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66.2 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76.3 Example of an order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Manufacturing process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77.1 Steelmaking process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77.2 Deoxidation process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77.3 Tube manufacture and delivery conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98.2 Chemical composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98.3 Mechanical properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118.4 Appearance and internal soundness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128.5 Straightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138.6 Preparation of ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138.7 Dimensions, masses and tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199.1 Types of inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199.2 Inspection documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199.3 Summary of inspection and testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2010 Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2210.1 Frequency of tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2210.2 Preparation of samples and test pieces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2311 Test methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2511.1 Chemical analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2511.2 Tensile test on base material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2511.3 Transverse tensile test on the weld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2511.4 Flattening test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2511.5 Drift expanding test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2611.6 Weld bend test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2611.7 Impact test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2611.8 Leak-tightness test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2711.9 Dimensional inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2811.10 Visual examination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2811.11 Non-destructive testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2811.12 Retest, sorting and reprocessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2812 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2812.1 Marking to be applied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2812.2 Additional marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2913 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Annex A (normative) Qualification of welding procedure for SAW tube production . . . . . . . . . . . . . . 30Annex ZA (informative) Relationship between this European Standard and the Essential

Requirements of 97/23/EC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 3EN 10217-1:2002 + A1:2005

Foreword to EN 10217-1:2002This European Standard has been prepared by Technical Committee ECISS/TC 29 ‘Steel tubes and fittings forsteel tubes’, the Secretariat of which is held by UNI.This European Standard has been prepared under a mandate given to CEN by the European Commission andthe European Free Trade Association, and supports essential requirements of the relevant EU Directive.For relationship with this directive, see Annex ZA.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, and conflicting national standards withdrawn, by November 2002 at the latest.Other parts of EN 10217 are:Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature propertiesPart 3: Alloy fine grain steel tubesPart 4: Electric welded non-alloy steel tubes with specified low temperature propertiesPart 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature propertiesPart 6: Submerged arc welded non-alloy steel tubes with specified low temperature propertiesPart 7: Stainless steel tubesAnother European Standard series covering tubes for pressure purposes is:EN 10216 Seamless steel tubes for pressure purposes.In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of the follow-ing countries are bound to implement this European Standard:Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, Malta, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom.

Foreword to EN 10217-1:2002/A1:2005This amendment to EN 10217-1:2002 has been prepared by Technical Committee ECISS/TC 29 ‘Steel tubesand fittings for steel tubes’, the Secretariat of which is held by UNI.This European Standard has been prepared under a mandate given to CEN by the European Commission andthe European Free Trade Association, and supports essential requirements of the relevant EU Directive.For relationship with this directive, see Annex ZA.This amendment shall be given the status of a national standard, either by publication of an identical text or byendorsement, and conflicting national standards withdrawn, by July 2005 at the latest.In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of the follow-ing countries are bound to implement this European Standard:Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal,Slovakia, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom.

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 4EN 10217-1:2002 + A1:2005

1 Scope

2 Normative references

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 5EN 10217-1:2002 + A1:2005

3 Terms and definitions

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 6EN 10217-1:2002 + A1:2005

4 Symbols

5 Classification and designation

6 Information to be supplied by the purchaser

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 7EN 10217-1:2002 + A1:2005

7 Manufacturing process

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 8EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 9EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 10EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 11EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 12EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 13EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 14EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 15EN 10217-1:2002 + A1:2005

Dimensions in mm

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 16EN 10217-1:2002 + A1:2005

Dimensions in mmTable 5 (concluded)

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 17EN 10217-1:2002 + A1:2005

Dimension in mm

Dimensions in mm

Dimensions in mm

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 18EN 10217-1:2002 + A1:2005

Dimensions in mm

Dimensions in mm

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 19EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 20EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 21EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 22EN 10217-1:2002 + A1:2005

10 Sampling

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 23EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 24EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 25EN 10217-1:2002 + A1:2005

11 Test methods

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 26EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 27EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 28EN 10217-1:2002 + A1:2005

12 Marking

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 29EN 10217-1:2002 + A1:2005

13 Protection

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 30EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 31EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 32EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 33EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 34EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 35EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 36EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 37EN 10217-1:2002 + A1:2005

Dimensions in mm

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---

Page 38EN 10217-1:2002 + A1:2005

Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,``,`-`-`,,`,,`,`,,`---