ETAP FAQ Usb Install 1600

8/2/2019 ETAP FAQ Usb Install 1600

1/14

TAP Installation FAQ # 1 - Installation Guide for ETAP 5.5.6 with USB Key ETAP-OTI 1600

ETAP Installation FAQ # 1

Installation Guide for ETAP 5.5.6 with USB Key ETAP-OTI 1600

scription: Complete Installation Guide for ETAP 5.5.6 using the USB Key ETAP-OTI 1600 model

rsion: ETAP 5.5.6, August 2007

blished: August 2007

ywords: ETAP Installation, ETAP License Manager, USB Key ETAP-OTI 1600

is document provides a step by-step installation of ETAP 5.5.6. After installation, ETAP 5.5.6 may prompt you for Activation Code the first time you run the software. This 36-character activation code is located on the ETAP CD sleeve. If u are upgrading from the previous release of ETAP, the activation code can be found on your existing ETAP CD sleeve.

stem Requirements

ardw are Requirem ent s - Recomm ended

0 Bus Projects

Intel Pentium IV 2.0 GHz or equivalent 1 GB of RAM

00 Bus Projects

Intel Pentium IV

3.2 GHz with Hyper-Threading Technology, or equivalent 1 GB of RAM (RDRAM or high-speed DDR RAM)

000 Bus Projects and Higher

Intel Pentium IV 3.0 GHz with Hyper-Threading (or dual core), or equivalent 2 GB RAM (RDRAM or high-speed DDR RAM)

al-Time Application - Server

Intel Pentium Xeon 3.2 GHz with Symmetrical Multiple Processing (DUAL) with Hyper-Threading (or Dual-Core), or better,and high-speed system bus or AMD equivalent

2 GB RAM (RDRAM or high-speed DDR RAM)

Configuration & Peripherals

Parallel Port, USB Port, or Serial Port (for Stand Alone Licensing only) CD-ROM or DVD Drive 5 to 80 GB Hard Disk Space (based on project size, number of buses) 19 Monitors Recommended (dual monitors highly recommended)

perat ing System Requirement s


2/14


Microsoft Windows 2000 (Service Pack 4) Professional or Server Microsoft Windows XP (Service Pack 2) Professional or Home Edition Microsoft Server 2003 (Service Pack 1) The ETAP 5.5.6 Vista compatibility program is provided in the following link: http://www.etap.com/support/downlo ads.htm

her Software Requirements

Microsoft Internet Explorer 5.01 or higher Microsoft .NET Framework v1.1

talling ETAP 5.5.6

To install ETAP 5.5.6, you must have administrative access to your computer or administrator credentials when prompted onWindows Vista.

Close all applications and insert the ETAP 5.5.6 CD, dated August 2007, into your CD-ROM drive.

ETAP installer will prompt you if previously installed version(s) of ETAP are detected. You have the choice to either uninstall the existing ETAP version(s) or continue with the current installation without removing the existing version(s). Itis not necessary to remove the existing installation(s) of ETAP.

tallation of ETAP requires installation of the ETAP 5.5.6 License Manager and ETAP 5.5.6.

nstalling ETAP 5.5.6 License Manager

1.1 ETAP Installer will start up and present the following screen. Select the desired application to be installed.r ETAPr ETAP Real-Time Server r ETAP License Manager

1.2 Select ETAP License Manager and click install to continue.

Installation of the ETAP License Manager 5.5.6 is required for the following licenses:

r ETAP Stand Alone License, using the USB Key ETAP-OTI 1600.r ETAP Network License

r the Stand Alone license, the ETAP application, License Manager, and USB key must be installed on the same PC.

th the Network license the License Manager and key are installed on a server PC and ETAP is installed on the client. However, the Network license has the option to install the ETAP application, License Manager, and key on the same PC.

continue with the installation instructions first identify the type of license you are using. A label on the key identifies the keyStand Alone or Network .

USB Key - ETAP-OTI 1600vious versions of the ETAP License Manager will be detected by the install and should be uninstalled from the Add/move Programs control panel.
http://www.etap.com/support/downloads.htmhttp://www.etap.com/support/downloads.htm


3/14


necessary, this message can be bypassed by running the Setup from the Run command and using the /z force mmand. The example below assumes the D: drive is the CD ROM.

AP Setup displays the ETAP License Manager Welcome dialog box for version 5.5.6. Click the Next button to continue.sure to remove any ETAP hardware keys from the computer.

e ETAP License Agreement is displayed. By clicking Yes you accept the terms of the Agreement.


4/14


e Setup displays the default path to install the ETAP License Manager. Click Browse to select a different path or click Nextcontinue.

e Setup requests the type of key you are using. The default key is the USB Key ETAP-OTI 1600 key. Select a differentnecessary and click Next to continue.


5/14


e Setup has enough information to begin the installation. Click Next to begin the file transfer.

e Setup will show the progress of the installation.


6/14


e Setup prompts to plug in the ETAP hardware key. Windows may or may not be able to load the drivers when the keyplugged in. Click Finish after plugging in the ETAP hardware key.


7/14


e Setup will attempt to start the ETAP License Manager (referred to in the Services control panel as Etaps Lic Mgr).is process may take a few seconds.

e Setup is complete if the service starts successfully. No reboot of the PC is necessary.

e Setup will notify the user if the service was not able to be started. An informational message will be shown theplication Event Log stating in detail why the service could not be started.

up will then prompt to restart the PC.


8/14


nstalling ETAP 5.5.6

2.1 Close all applications and insert the ETAP 5.5.6 CD into your CD-ROM drive.

ETAP installer will prompt you if previously installed version(s) of ETAP are detected. You have the choice to either uninstall the existing ETAP version(s) or continue with the current installation without removing the existing version(s). Itis not necessary to remove the existing installation(s) of ETAP.

2.2 ETAP Installer will start up and present the following screen. Select the desired application to be installed.

ETAP ETAP Real-Time Server ETAP License Manager (for Network users)

Select ETAP and click Install to continue.

ETAP 5.5.6 installation will begin with the self-configuration of the Windows Installer as shown in the following screen.


9/14


If the installation program does not detect the Microsoft.NET v1.1 Framework components in the operation system,ETAP 5.5.6 Installation continues with the setup of the .NET Framework components.

2.3 Click Next on the Welcome screen to continue.

2.4 The installation and use of ETAP is governed by the terms and conditions of the ETAP License Grant and Agreement. These terms must be accepted before the installation can continue. Click Next.


10/14


2.5 The installation screen displays hardware and software requirements as well as other useful information. Click Nextto continue with the installation.

2.6 Setup requires the name of a destination folder on your hard drive where you would like the ETAP 5.5.6 applicationto be installed. The default destination folder is C:\ETAP 556. To install the program in a different location, click Browseand select or type a new destination folder. Click Next.


11/14


2.7 Select the type of installation to be completed. Note that the default choice is Typical. Click Next to continue withthe installation.

2.8 The Start Copying Files screen provides the opportunity to verify the setup information. If the setup information iscorrect, click Next to continue the installation.


12/14


2.9 Windows 2000 users will be required to restart their computer. Select the Yes, I want to restart my computer now. option and click Finish. Windows XP users will not be asked to restart their computer.

ETAP 5.5.6 program shortcut is placed on the desktop when the installation is complete.

ista Compatibilityr Microsoft Vista Operating Systems go to the following link and download the ETAP Vista Compatibility program. http://

ww.etap.com/support/downlo ads.htm

ETAP License WizardWhen you launch ETAP 5.5.6, the ETAP License Wizard prompts you to choose between a Stand Alone Key or Network Key.

u MUST select Network Key regardless of whether your ETAP configuration is for a Stand Alone or Network license.
http://www.etap.com/downloads.htmhttp://www.etap.com/support/downloads.htmhttp://www.etap.com/support/downloads.htmhttp://www.etap.com/downloads.htm


13/14


f a Network Key is used, the computer name or IP address of ETAP License Server must be specified. For a Stand Aloney enter a period ( .). Click Next to continue.

Upon successful detection of the key, click Finish to complete the ETAP License Wizard.


14/14


After installation, ETAP 5.5.6 may prompt you for an Activation Code the first time you run the software
http://www.etap.com/

Date post:	06-Apr-2018
Category:	Documents
Upload:	azazelux
View:	281 times
Download:	1 times

ETAP FAQ Usb Install 1600

Documents