final BoQ 2.11.11.xlsx

MINISTRY OF FOREIGN AFFAIRS

PACKAGE 2: Finishing, Mechanical and Electrical Works

ITEM DESCRIPTION UNIT QTY RATE Total

1.1 HOLLOW CONCRETE BLOCKS WORKS

a. Hollow Blocks (10 Ten) cm. Thick. M.S 4900 0.00

b. Hollow Blocks (20 twenty) cm. Thick for internal partitions

and parapet.M.S 620 0.00

TOTAL CARRIED TO SUMMARY 0.00

1.2 PLASTERING WORKS

1.2.1

Supply and install internal plastering for walls, ceilings,

columns, drop beams, brackets,sofits of slabs & beams, shaft

walls, projections, sills, up stands, openings, sleeves,

expansion joints...etc,composed of 3 coats, a bond coat 1:1,

base coat 1:4, and finish coat 1:5 as specified. The price

includes the corner beads, casing beads, metal lath,

scaffoldings, shuttering, surface preparation such as existing

fairface surfaces or structural elements, making good to

frames& openings bonding agents and the requirements as

specifications and related standards .the contractor shall take

into considerations the site conditions in existing surfaces or

elements scheduled for plastering.

MS 28450 0.00

1.2.2

Ditto, but supply and install external plastering for parapet&

stair cases walls, external walls or shafts, planter walls, ramps

walls, utility rooms, and wherever needed composed of 3 coats

a bond coat 1:1, a base coat 1:4 and a finish coat 1:2 with

water proofing materials (SBR) all as specifications and related

standards.

MS 320 0.00

TOTAL CARRIED TO SUMMARY 0.00

November 2011 1 / 46 UNDP-PAPP




1.3 TILING WORKS

1.3.1

Supply and install granite porcelain full body Grade (A) floor

tiles (PT2) 30*30*0.8 cm of different colors as made by CIPA

Italian ceramic, or equivalent ,Matt finish , the price includes

sand cement mortar bed (1:3) , sand cement fill ( dry mix),

cutting& trimming around floor utilities& openings including

grouting with special grout materials ,the tiles shall be laid and

fixed in patterns, style and forms as directed by the Engineer.

MS 1000

1.3.2

Supply and install Delicate cream 042 (DT1) Grade (A) floor

tile 60*60*2 cm,Matt finish or equivalent, the price includes

sand cement mortar bed (1:3) , sand cement fill ( dry mix),

cutting& trimming around floor utilities& openings including

grouting with special grout materials ,the tiles shall be laid and

fixed in patterns, style and forms as directed by the Engineer.

MS 1545

1.3.3 Ditto, but 40*40*2 cm(DT2) MS 850

1.3.4 Ditto but terrazzo tiles with Italian marble chipping MS 600

1.3.5

Supply and install 20x20x0.8cm Porcelain Spanish tiles class

(A) tiles from Albero or equivalent for walls cladding of different

colors. The tiles shall be laid and fixed to the walls in patterns,

style and forms of grouting& jointing as directed by engineer

using approved adhesive materials. The price also includes the

cost of surface preparation to receive tiles, which shall include

two coats of cement plaster (scratch and float coat), approved

adhesive materials, grouting, aluminum protection angles as

approved by the engineer.

MS 2050

To be carried to next page





Sum from Previous Page

1.3.6

Supply and install Granite Porcelain full body floor tiles Grade

(A) 60x60x.9 cm (M.T) Italian Cipa , Spanish CK COLORKER

or equivalent of different colours,Matt finish or equivalent, the

price includes sand cement mortar bed (1:3) , sand cement fill

( dry mix), cutting& trimming around floor utilities& openings

including grouting with special grout materails,the tiles shall be

laid and fixed in patterns, style and forms as directed by the

Engineer.

MS 500

1.3.7

Supply and install 3cm thick Delicate Cream 042 for stair treads

of required length polished one face & edge with chamfered

edges all as per details D20,D21/ AD09 . The treads should be

bedded on 3cm mortar (1:3), sand cement fill ( dry mix), and

pointing with special grout materials The rate includes an edge

piece for water stop.

MR 610

1.3.8 Ditto, but 2cm thick risers. MR 610

1.3.9 Ditto, but 2cm thick for steps skirting. MR 98

1.3.10Ditto, but 2cm thick for landings skirting, covering middle parts

under the hand rails and related up stands.MR 253

1.3.11

Supply and install 3cm thick local marble grade (A) free from

defects for sills, thresholds and where needed set in cement

mortar bedding. Price to include grouting, polishing of face and

seen edges.

MR 180

1.3.12 Ditto but Delicate Cream 042 MR 1210

1.3.13

Supply and cast sloped concrete screed B250 for car park

flooring machine to meet the levels of the existing floors with

minimum 3cm thick at drain points, the surface finish is

machined trowelled with hardeners including Epoxy paint, the

rate shall include surface preparations for existing concrete

flooring such trimming the projections, patching,

levelling,treatements for concrete edges including floor joints

and making goods around openings.

M.S 2000

TOTAL CARRIED TO SUMMARY





1.4 FALSE CEILING WORKS

1.4.1

Supply and install suspended ceiling for bathroom, utilities,

kitchens and wet areas made from 30cm non perforated formed

galvanized metal trays of 0.6mm thick and 45mm high. The

trays should be supplied pre painted and oven cured. The unit

rate shall also include acoustic rock wool mats, 25mm thick and

25kg/m3 density, wrapped in black non inflammable dust proof

sags in accordance with specifications and the related

Standards.

M.S 480

1.4.2

Ditto, but 60x60cm acoustic tiles, type Armstrong regular edge

or equivalent. The tiles shall be Non Combustible type and the

textures/ surface finish of the tiles as directed by Engineer.

M.S 5100

1.4.3

Supply and install gypsum boards for ceilings including drop

beams, projections, steps forms, architects elements, brackets

cladding and for other decorative works. The price shall

includes complete suspension system, main & sub main steel

structures, suspension clips, edges, recess/ cuts/ slots for

services and associated supports, anchors, jointing, making

good for jointing, accessories for connections with other

adjacent types of ceilings, provisions to other decorative

finishes, to any shape and patterns to complete the works as

per details and specifications.

M.S 2120

1.4.4

Ditto, but gypsum boards and decorative hard wood American

walnut ceiling for ministers room and where required and

directed complete as per details and specifications.

M.S 100

1.4.5

Supply and install gypsum board partition walls cladding from

two sides complete with all fittings such as walls galvanized

studs, anchors, ends terminations, provisions for all openings

with required frames and supports, cuts/ slots for services,

preparation for works related to the adjacent finished elements,

making good for jointing...etc, complete all in accordance to the

details and specifications. measurements from one side only.

M.S 910






1.5 CARPENTRY WORKS

1.5.1

Supply and Fix Wooden Doors 4.5 cm Thick single or double

sashes. With Swedish wood frame (3.4 * 90) mm and hard

wood exposed edges (45 * 35) mm, high quality Class (A)

Formica veneer 0.6 mm on both sides, color as directed by

engineer. Door paneling/ filling of soft wood 4.5*3.5 cm each 4

cm. Door frames of hardwood 4cm thickness and width

according to the wall thickness and Allowance of 4-6 cm thick

for plastering and tiling purposes, immersed in wood

preservative before erection then embedded completely in sand

- cement mortar and completely anchored as per specification.

Architrave of Hardwood (7*1.2) cm, price to include

ironmongery, kick plates of aluminum 10cm height for bath

room doors, U shaped both sides, and at the bottom door

stoppers, , gaskets cylindrical Lock (Approved by Palestine

Standards Institution), and painting in three coats of oil paint in

addition to primer coat. All as per detailed drawings and

specifications.

a) WD1 Structural opening size (180 * 210) cm. NO. 5

b) WD2 Structural opening size (130 * 210) cm. NO. 2

c) WD3 Structural opening size (140 * 210) cm. NO. 13

d) WD4 Structural opening size (80 * 210) cm. NO. 14

e) WD5 Structural opening size (90 * 210) cm. NO. 104

f) WD6 Structural opening size (90 * 210) cm. NO. 11

g) WD7 Structural opening size (80 * 210) cm. (but with

bathroom cylinder type(keyless) type "Domicile" Model

002004/B213 stainless steel)

NO. 69

h) WD8 Structural opening size (80 * 210) cm. NO. 7

i) WD9 Structural opening size (110 * 210) cm. NO. 32

j) WD10 Structural opening size (140 * 210) cm. NO. 1

k) WD11 Structural opening size (90 * 210) cm. NO. 1

L) FW1 Structural opening size (70 * 210) cm shaft door NO. 10







1.5.2

Supply & Install top and bottom Wooden Kitchen Cabinet.

Cabinet's Top shall be with high quality Italian granite 30 mm of

selected color & finish. thick with polished surface and seen

edges. Cabinet Sides, Elevations, Partitions, Shelves and

Drawers front-side shall be of 17-mm. thick panel wood,

laminated internally with 0.5 mm. Thick Formica sheet, and with

0.8mm thick Formica sheet externally. The whole cabinet shall

be framed with Hardwood (Zen) bands size (60*40) mm

screwed to steel frame and covered with 0.8mm thick Formica

sheet. Rear sides of cabinets and drawer's bottom shall be of 6

mm, thick Veneer covered internally with 0.5mm thick Formica

sheet. Price to include cabinet terrazzo flooring (30 * 30 * 3)

cm., and terrazzo skirting (30 * 10 * 1.5) cm., ironmongery,

handles, granite skirting& edges, recess for sink and related

fixtures, fixing the sink, sealants, two coats of lacquer paint over

one primer coat and all the accessories as per drawings and

Specifications .

SIZE: Height (90) cm. Width (60) cm. as per detailed drawings)

a-for kitchen and Canteen M.R 28

1.5.3

Supply and install 2cm thick American Walnut wood cladding

panels with 2 cm aluminum strips between panels. Price

includes adequate backing wood structures with required

bracing according to drawings, fixing, painting finishing with

adjacent elements, trimming, jointing, edges and all decorative

accessories needed to complete the work.

M.S 800

1.5.4

Supply and install hard wood slat stained to match American

Walnut. Price includes 6mm clear glass to slot between wood

slat walls, and hard wood upright behind the horizontal slats.

Price also includes painting and all accessories needed to

complete the work.

M.S 105






1.6 METAL WORKS

1.6.1

Supply, fix and operate sliding Puff Aluminum Windows.

Extrusion Section 9900 napco or equal three channel, with

Anodized finish (10AA) 10-15 micron . In color approved by the

Engineer. Price to include, 6 mm double tented Float colored

glazing , fly screen, handles, gaskets, rubber strips, sealant and

all other accessories and fittings to complete works as per

drawings, specifications and manufacturer recommendations.

i. Window Type W-2 size (1.00*1.40) m. NO. 2

ii. Window Type W-4 size (3.4*1.20) m. NO. 1

iii. Window Type W-5 size (1.05*1.20) m. NO. 1

iiii. Window Type W-6 size (1.50*1.20) m. NO. 4

iv. Window Type W-3 size (0.60*0.80) m NO. 35

1.6.2 Supply and Fix stainless steel hand railing with cable railing

system complete as per Detailed Drawing.M.R 130

1.6.3

Stair Handrails as shown in drawings. Price to include wood

handrail, fixing complete, oil paint three coats in addition to

primer coat according to details.

M.R 450

1.6.4 Ditto, but grab bars for staircase as in drawing. M.R 60

1.6.5 Ditto as (a) above but for handicapped Ramps. as in drawing M.R 60

1.6.6

Supply and Fix Steel Windows louver type consist of 4 x 8 cm

metallic main and sub main profiles, 2mm thick galvanized

metal sheet louvers, 2mm thick windows main frame of required

wall thickness. Price to include fixing complete, ironmongery,

cylinders, cylindrical locks handles, 6 mm. glazing,12 X 8 mm

glazing beads, anchors, oil Paint in three coats in addition to

two primer coats. as per drawings, specifications and

instructions of supervisor engineer.

a. For generator and transformer room (W1) NO. 2







1.6.7

Supply and Fix Steel Doors louver type consist of 4 x 8 cm

metallic main and sub main profiles, 2mm thick galvanized

metal sheet louvers, 3mm thick galvanized prefabricated door

frames with required slots& brackets for door locks & cylinders,

including recess for hinges with required wall thickness. . Price

to include fixing complete, ironmongery, cylinders, cylindrical

locks handles, 6 mm. glazing,12 X 8 mm glazing beads, 3x 20

mm cover beads, heavy duty hinges, anchors, welding,

grinding, finishing and oil Paint in three coats in addition to two

primer coats. All as per drawings, specifications and


a. Steel Door Type MD1 Louver door (180* 210)

cm. NO. 3

c. Steel Door Type MD3. Louver door (250*210)

cm. NO. 1

d. Steel Door Type MD4 Louver door (200*210)

cm.NO. 2

1.6.8

Supply and Fix Fazzon Steel Doors covered with 1.5 mm thick

steel sheets both sides including metallic main and sub main

profiles,3mm thick galvanized prefabricated door frames with

required slots& brackets for door locks & cylinders, including

recess for hinges with required wall thickness. Price to include

fixing complete, ironmongery, cylinders, cylindrical locks

handles, heavy duty hinges, anchors, dowels, foam fill, welding,

grinding, finishing and oil Paint in three coats in addition to two

primer coats. All as per drawings, specifications and


a. Steel Door Type MD2 Panel door (200*210) cm. NO. 4

b. Steel Door Type MD5 Louver door (160*240) cm. NO. 1

c. Steel Door Type MD6 Louver door (160*240) cm. NO. 3

1.6.9

Supply and install napco aluminum or equivalent with 12mm

thick Tempered Glass doors with pattern. Price includes all

accessories, handles, locks, closers, pneumatic door hinges, all

fixed elements, spider if necessary. Price also includes

electrical motor for sliding door.

a) GD1 sliding door NO. 6

b) GD2 one leaf NO. 72

c) GD3 Sliding door NO. 2

d) GD4 Sliding door NO. 2







1.6.10

napco plus Aluminum or equivalent 50 mm Curtain walls . Price

includes double pane glass with 6mm thick tempered outer

pane and 6mm tempered inner pane, price also includes

tempered glass doors, fittings, hinges, locks, sand blasting

patterns, bolts, and all connections as manufactured by Dorma

or equivalent, fittings colors same as aluminum color. Price also

includes window openings (napco accessories)including fly

screen panes. Price also includes the vertical and horizontal

panels for the sky lights, as well as aluminum sun visers..

Contractor to supply all shops drawings prior to execution of

work. Price includes all necessary steel structure, including

galvanizing and painting of all elements, all supports, brackets,

etcH Price also includes aluminum sheet cladding of all

exposed concrete and steel elements ( ALKABOND) as shown

on drawings. Fabrication and assembling shall be performed by

high professional suppliers. Silicon used should be industrial

silicon from approved company,

M.S 4500

1.6.11 Ditto, but for internal Curtain wall and without sun visers. M.S 550

1.6.12 Ditto, but skylight. M.S 350

1.6.13

Securit glass partitions 12mm thick of different heights,

dimensions, shape and patterns complete with stainless steel

frames, and supports, stainless steel spider joints, clear rubber

seals, etc..with all accessories in accordance to the standards

and manufacturer recommendations.

M.S 2171

1.6.14

Supply and install stainless steel staircase complete to

specified dimensions and heights as per details, price includes

all supporting structures such main& sub main profiles, posts,

steel plates, st. steel brackets, anchors, grinding, making good

for jointing, painting..etc. Price also include st. steel coverings/

cladding, 2cm Non slip glass treads& landings, 25mm HDF

layer, st. steel railing with required cables railing system,

connections& finishing with the adjacent existing steel bridges.

All accessories and necessary fittings to complete the works in

accordance to specifications and drawings.

L.S 1

1.6.15

Supply, install and construct steel structure comprised of steel

trusses as shown in drawings. The trusses to be comprised of

circular pipes of various diameters, minimum thickness to be

5mm. including main, sub main, secondary profiles, bracing

members, jointing, steel plates, anchors& anchor bolts, fittings,

hinges, supporting, welding, riveting and Elastomeric pads

complete. Price includes all necessary scaffolding, assembling,

connections with other related works, manufacturing to be

performed by authorized and approved steel fabricator. all

bolts to be Grade 8.8 minimum. price also includes sand

blasting and three coats of epoxy, Filings metal joints, painting

with decorative colors as directed and surface preparations to

host the structures. The works includes all supporting concrete

elements such as columns, brackets, plinths....etc, complete

including steel reinforcement. The works shall be co ordinate

with related finishing layers such as glazing panels with

required profiles proposed for covering the structures.

MS 350





1.6.16

Supply, install and construct steel structure comprise of steel

frames such as I Beams, girders, purlines, all other steel

profiles, bracing members, jointing, steel plates, anchors&

anchor bolts, fittings, hinges, supporting, welding, sand blasting

and three coats of epoxy, Filings metal joints. price includes

also all finishing works for the steel structures complete with all

materials in accordance to specifications and details. Price shall

include galvanized steel sections, supports, sheets of required

dimensions and thickness, angles, anchors, bolts, plates,

welding, connections the steel structures elements with other

related structures. Price also includes upper& lower 2cm thick

Non slip Illuminated glass, st. steel rails with cable railing

system, recess for lighting fixtures, st. steel railing and cable

railing system for the side walks and for all surrounding areas

located at every side walks levels and all decorative

accessories.

MS 160






1.7 Insulation, Roofing And Expansion Joints

1.7.1

Supply and cast in place lightweight plain concrete for screed to

roof with 1% slope, cast to falls not less than 3cm thickness in

the drain point, rate to include lining and hunching 10x10 cm

with (45˚) to the edge of roof screed and parapet , rate also

include smooth surface finish to receive bitumen and all

requirements as per specifications, drawings and Engineer's

.instructions

M.s 1400

1.7.2

Supply and install roof water proofing membrane of bitumen

,rolls5mm thick covered with quartz granules, Pazkar or

equivalent, for main roof, stairs roofs, parapet walls and where

required the price includes the application of primer coat GS

,at a rate of 25 kg/m2 installation of 15*15cm angle fillet 474

,grooves, groove sealant, groove cover, joints over lapping

,backing sheets or pieces all around external& internal corners

roof drains, machines foundations or up stands, roof door

thresholds and silver paints along the joints and all necessary

material and workmanship to complete the works as shown in

the drawings and as per manufacturer instructions and codes of

.practice

M.s 2100

1.7.3

Supply and Fix Aluminum Cover to Expansion and/or seismic

,Joints for floors, walls and ceilings. Price to include mastic fill

,backing rod, fixing with galvanized clips every 30 cm. flashing

cutting, lining, concrete upstand where required and all

accessories in accordance with details and relative

.specifications

1.7.4 a. Internal Horizontal expansion joint through floor and tiles MR 430

b. Ditto but above false ceiling without cover MR 430

c. External, Vertical Expansion joint below grade level MR 50

d. External, Vertical Expansion above ground MR 115

e. Internal Vertical expansion joint through walls MR 600

f. Internal Vertical expansion joint through Curtain Wall MR 90

g. External, Horizontal Expansion joint on roof MR 65

h. External, Horizontal Expansion joint on Parapet Walls MR 30







1.7.5

Supply and cast (Grade B-200) Concrete Cast-In-Place

Expansion Joint Cover. Approx. Size (40 * 55) cm. Price to

include concrete block, three coats of plastering, steel

reinforcement, polystyrene, mastic fill, backing rod, galvanized

steel plate cover, waterproofing membrane, and all needed

works.

MR 65

1.7.6

Supply and spread 3 cm layer of Polyethylene of 30 kg/m3

density on concrete and block walls of external facades. The

price includes protecting the stone and cleaning afterwards

MS 3000

1.7.7

Supply and lay Soundproof polyester nonwoven coated with a

synthetic film for reducing footstep noise of 3.8 mm thickness

and 340 g/m2 weight like PhonoPar from Freudenberg Politex

or equally approved. Installation should be according to

manufacturer instructions.

MS 3000

1.7.7Supply and apply 5cm sand cement screed and two layers of

cementious polymer waterproofing layersMS 480

1.7.8

Supply and cast lean mix concrete to encase projected columns

at roof to the required dimensions and heights, price to include

2 cm thick plastering, grooves, sealant& galvanized cover and

water proofing membrane including primer coat. price also

includes Supply, Build stone coping for head of columns

L.S 1


1.8 PAINTING WORKS

1.8.1

Supply and paint high quality supercryl paint for walls and areas

as indicated in finishing tables and as directed by the Engineer

composed of two coats of complete putty and 3 coats of "

supercryel " paint all as per specifications and manufacturer

recommendations.

M.S 16100

1.8.2

Supply and paint three coats of high quality Polycide paint for

ceilings complete all as per specifications and manufacturer

recommendations.

M.S 4600

1.8.3

Ditto, but three coats of high quality Polycide paint for Gypsum

Board ceilings including treatments/ filling/ finishing of joints and

projections and stepsHetc. complete all as per specifications


M.S 4500

1.8.4

Supply and paint high quality supercryl paint for external

surfaces exposed to weather conditions and for areas as

directed by the Engineer composed of two coats of complete

putty and 3 coats of " supercryel " paint all as per specifications


M.S 600

1.8.5

Supply and paint acrylic paint for parking walls , columns, for

parking lines, and where needed complete all as per related

standards, specifications and manufacturer recommendations.

M.S 1350






1.9 EXTERNAL WORKS

1.9.1

Trench excavation for foundations of retaining walls and

boundary walls and where ever required, in any kind of soil, to

the dimensions and levels shown in the drawings.

Price to include back filling with the

excavated soil if suitable or substituting same with selected

approved imported soil, and removal of extra and unsuitable

soil . Back filling shall be on layers of 200 mm thick with

watering and compacting to (95%)to comply with modified

AASHTO F.D.T.(T-80)

M.C 1500

1.9.2

Supply and well compact base course layer 20 cm thick after

compacting to 100% , in accordance to Modified AASHTO

Density Test ( CT 180). Price to include leveling, compacting,

watering and surface finishing to receive other scheduled

finishing works complete all as per specifications and details.

M.S 1550

1.9.3

Supply and cast Plain Concrete Grade B '200'. Including Form

work , scaffolding, vibration, labors, curing , and all related

works. a. Blinding 10 cm thick under Foundations of

external seating and under foundation, walls, beams, etcHand

as where directed by the engineer.

M.S 400

1.9.4

Ditto, But Reinforced Concrete Grade ' B 250 ‘ of cement

content not less than 300 kg /m3 for planter walls, retaining

walls, security room walls, foundations, beams, up stands..etc

and ever required as directed by the Engineer.

M3 330

1.9.5

Ditto, But 25cm thick Reinforced Concrete Grade ' B 250 ‘ of

cement content not less than 300 kg /m3 for roof slab of

external security rooms, under ground fuel tank slab..etc and

ever required as directed by the Engineer.

M.S 65

1.9.6

Supply and cast Reinforced Concrete, Grade B250 of cement

content not less than 300 kg /m3. a-15 cm thick for Slab on

Hard Core. Including edge beams, steel trowel led

finish,levelling, polyethylene sheets 500micron, construction

joints, curing ...etc, complete all as per details and

specifications.

M.S 1600

1.9.7Ditto, but b - 10cm for external security flooring, stairs

landings, seating's and where directed.M.S 100

1.9.8

Apply Cement and Sand Plaster:Two coats over one slurry coat

to walls and where required including metal lath of any shapes

and sizes as specifications, plaster beads, plaster corner and

stops. The fourth coat (shabriz) Topping. For planter walls,

price to include waterproof additives.

M.S 200







1.9.9

Supply and Build; cement tiles . Price to include bedding and

,jointing in cement and sand mortar, pointing with white cement

.required sand fill, and on site grinding, polishing and cleaning

M.S 280

1.9.10

Stone treads and risers : Stone Jamma’ in first class and first

quality Textured matabbah for external stair. Treads of 5

cm thick and Risers of 3 cm. thick. Price shall include supplying

and installing Stone Jamma for stair flight skirting in parallel

setting to the nosing line at an average height of 12 cm. and 30

mm. thickness, and Stone Jamma’ water stop (5cm wide x 3cm

thick x length as wide as the tread of the stair minus riser

thickness) fixed at the end of treads. Also the price to include

filling under tiles with cement and sand 1: 6 ratio, bedding in

cement mortar, grouting, pointing, polishing of face and all

related works.

MR 120

1.9.11

Supply and Install Local Marble Coping, ( 3 cm thick)...etc, in

cement mortar bedding price to include grouting, polishing of

face and seen edges.

M.S 170

1.9.12

Supply and build stone walls to the full length and height as

shown in the drawings , 7cm thick Delicate Cream 042

according to drawings for planters and other walls as required

and directed by the Engineer. Price to include B250 concrete

backing, anchors,concrete blocks, 2cm insulation, pointing

...etc, complete all specification and drawings.

M.S 130

1.9.13

Ditto, 5cm thick Delicate Cream 042 cladding for walls including

fixing, scaffolding, supports, anchors, wire mesh( Ф8mm/

20cm), concrete backing, pointingH.etc, complete all as per

specifications and details.

M.S 550

1.9.14

Supply and install stairs handrails as shown on drawings. Price

to include Fixing complete, oil paint three coats in addition to

primer coat.

M.R 120

1.9.15Supply, install, spread, and make good, 30cm. agricultural soil

in areas designated on drawings. M.S 400







1.9.16

Bituminous Construction:

Supplying, Spreading and Compacting 6 cm Thick Layer (After

Compaction) of Bituminous Wearing Course (3/4’’), All

According to Specifications, -Drawings and Directions of The

Engineer, Price to Include Furnishing and Applying Bituminous

Prime Coat (MC-70) or Equivalent (Rate of Application 1.2 - 2

kg/m2) to A previously Constructed Layer.(Optional).

M.S 500

1.9.17

Supply and install Concrete Pre-cast curb stone for

sidewalks, and where instructed (100x25x17cm). Price

includes necessary excavations, casting of blinding B200

concrete footing, R.C Beam with steel reinforcement, cement

mortar, finishing for curves, smooth jointing and pointing,

compaction of sub-grade, and all requirements according to

drawings and specifications.

M.R 300

1.9.18

Road marking: continuous and/or Intermittent Road

Marking in Reflectolized Thermoplastic Material (Painted

Area Only) For Lines, Arrows, and ChevronsCetc As

.Directed By The Engineer, All According to Specifications

M.S 65

1.9.19

Ditto, but for Curb Stone marking: marking: continuous

and/or Intermittent Road Marking in Reflectolized

Thermoplastic Material (Painted Area Only) For Lines, Arrows,

and ChevronsHetc As Directed By The Engineer, All According

to Specifications.

M.R 300

Deformed high yield steel bar reinforcement of various

diameters, characteristic strength FY=420N/mm2 for concrete

reinforcement, as shown on drawings and according to

specifications.

TON 130






No Total

1.1 HOLLOW CONCRETE BLOCKS WORKS

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9 EXTERNAL WORKS

Total carried to main summary

TILING WORKS

FALSE CEILING WORKS

CARPENTRY WORKS

METAL WORKS

Insulation, Roofing And Expansion Joints

SUMMARY FINISHING WORKS

Division 1

Item

PLASTERING WORKS

PAINTING WORKS





Sanitary and Drainage Work

2.01 European Toilet

2.01.01

Supply and install White Vitreous China European type wall

mounted toilet with P trap complete with concealed flush tank ,

fittings, chrome plated 13mm stop valve and side tap. Price to

include concealed flush tank, water tap, seat with cover

including stainless steel hinges, stainless steel toilet paper

holder for single roll fixed to wall, hand set biddet comprising

chrome plated shower type sprayer and flexible hose minimum

1 meter long. and all other fittings as per drawings and

specifications.

No 60

2.01.02 Ditto but for handicapped, with sides and back hand rails No 8

2.02 Wash Basin

2.02.01

Supply and install White Vitreous China semi pedestal Wash

Basin, size (40 * 56) cm complete with all fittings, valves,

chrome plated siphon trap, the price also includes the mixer ,

mirror 40*60cm with stainless steel frame and any other

necessary parts as per drawings and specifications.

No 65

2.02.02Ditto but with marble counter compatible with the type and

quality of the civil interior finishNo 5

2.02.03As in item 2.01, but with vertical sliding movement for

handicapped use.No 8

2.03 Kitchen Sink

2.03.01

Supply, install and commissioning stainless steel single bowl

kitchen sink 50CM*60CM, complete with chrome plated mixer

for kitchen sinks c/w hand spray set and retractable hose,

supports, waste outlet, tail piece, PVC P-trap, as per drawings

and specifications.

No 10

2.03.02 Ditto but double bowl. No 1

2.04 Bathtub

2.04.01

Supply, install and commissioning of Vitreous China bath tub.

Size is 800*1800mm, complete with shower head, diverter,

hand spray,hose, bracket, and all accessories, waste outlet as

shown in the drawings and specifications .

No 2

2.05 Floor Trap

2.05.01

Supply and install PVC Floor Trap. Price to include siphon to

be fixed in reinforced concrete, (15*15 ) double chrome plated

cover one grated and one-closed. and all other fittings needed

to comply with the drawings and specifications .

No 68

2.05.02 Ditto but suspended No 10

2.05.03 Ditto but 4/2" F.D. No 15

2.06 UPVC Drainage Pipes

2.06.01

Supply, installation, testing and commissioning of 2" white color

UPVC drainage and ventilation pipes down to manholes with all

required white fittings including excavation, back filling, incasing

with concrete and roof vent caps, including connections as

shown in drawings and in accordance to specifications.

MR 350

2.06.02 Ditto but 4" MR 900


DIVISION 2 - MECHANICAL WORKS

Item Description UNIT Qty Rate Amount






2.06.03

Ditto but 6” External Sewers of UPVC pipes between

manholes. Price to include trench excavation, trench bottom

leveling and preparation, bedding in sand, supply of pipes, back

filling with selected material, jointing all fittings, testing, cleaning

and all related works to complete as per Drawings and

Specifications.

MR 50

2.07 HDPE Drainage Pipes

2.07.01

Supply, installation, testing and commissioning of HDPE

drainage with all required fittings including excavation, back

filling, including connections as shown in drawings and in

accordance to specifications.

Size4-inch diameter.

MR 140

2.07.02 Ditto, but size 2" MR 70

2.08 Manholes

2.08.01

Supply and install precast Manholes of various diameters and

to any depth. Price to include excavation, concrete works, back

filling, cement plaster, benching,rubber gasket at inlets and

outlets, Cast Iron medium capacity cover and all necessary

works to comply with drawings and specifications.

2.08.02 60cm*60cm No 3

2.08.03 80cm*80cm No 1

2.09 Floor Clean-out

2.09.01

Supply and install 4” (Clean Out), of drainage Network. In size

and location shown in the drawings and where necessary,

including (15*15)CM chrome plated screwed in cover and all

needed to complete work as specification and drawings.

No 48

2.09.02 Ditto but suspended No 12

2.10 Rain Water Drain:

2.10.01

Supply, installation and commissioning of Cast Iron rainwater

roof drain 20cm x 20cm. The price includes horizontal 4" UPVC

pipe to connect with the vertical rain pipe. Locations are shown

in drawings and in accordance to specifications..

No 8

2.11 Rain Pipes

2.11.01

Supply, installation, testing and commissioning of 4" white

UPVC rain water pipes with all required fittings of the same

make and color, including excavation, back filling, and roof vent

caps, including connections as shown in drawings and in

accordance to specifications.

Mr. 320

2.12 Water Grills

2.12.01

Supply and install, and commissioning of cast iron grills, and

average depth is of 30cm and width 40cm. located on drawings

.Price includes painting, and smooth sloped concrete bedding

in drawing the length is as shown in drawing .All as shown in


Mr. 10

2.12.02 Ditto but stainless steel Mr. 2







Domestic Hot and Cold Water Works

2.13 Electric Water Heater

2.13.01

Supply and install of electric water heater of capacity 60 liter

with automatic thermostat, the price includes all necessary

valves, electrical connections, cables and all other fittings as

per drawings and specifications.

No 46

2.14 CPVC Pipes

2.14.01

Supply and install CPVC pipes for cold and hot water pipes(16

bar) The price includes other fittings as per drawings and

specifications.

2.14.02 25mm Mr. 750

2.14.03 32mm Mr. 120

2.14.04 40mm Mr. 170

2.14.05 50mm Mr. 150

2.14.06 63mm Mr. 30

2.14.07 75mm Mr. 30

2.14.08 110mm Mr. 100

2.15 XLPE cross-linked polyethylene

2.15.01

Supply, install, and commissioning of XLPE cross-linked

polyethylene pipes, for all branches between sanitary fixtures

and manifolds. The price includes the non-corrugated sleeves,

and plastic box that contain the elbow or injasa for fixing in the

wall. And the brass elbow itself for the connection to angle

valve, with flush chrome plated hole cover, 16mm internal

diameter, as in drawings and in accordance to engineering

instructions and specifications

Mr. 1200

2.16 Water Collectors

2.16.01

Supply and install of copper collector for domestic water the

price includes all fittings (vent, valves on main line and

branches),and the steel cupboard 2mm oven painted and all

other fittings, all of which shall be from one manufacturer, as


2.16.02 3/4" COLL(1 outlet) No 20

2.16.03 3/4" COLL(2outlets) No 21

2.16.04 3/4" COLL(3outlets) No 25

2.16.05 3/4" COLL(6outlets) No 1

2.16.06 1" COLL(4outlets) No 4



2.17 Water taps

2.17.01

Supply and install water taps for irrigation and other services

as shown in drawings and specifications. The price includes

connecting to water pipe and all required fixing on wall or on

places approved by the engineer using all required accessories

No 18







2.18 Galvanized Water Pipes

2.18.01 Supply and install 2" main water supply

from water meter to the water well. The price includes all

needed to complete the job according to drawings and

specifications.

MR 100

2.18.02 Ditto but 1" MR 35

2.18.03 Ditto but 3/4" MR 10

2.19 Water Tanks

2.19.01Supply and install PVC water tank 500l..The price includes the

base, float valves, all needed to complete the job.No 1

2.20 Water Filter

2.20.01Supply and install water filter as shown in drawings and

specificationsNo 1

2.21 Water Softener

2.21.01Supply and install water softener as shown in drawings and

specificationsNo 1

2.22 Water Reservoir

2.22.01

Supply and install all required works and material for the first fix

of the water well. The price shall include overflow, vent, water

inlets and outlets, float valves, electric float switches, fire

fighting inlets and outlets and all required fittings and material

as per drawings, specifications the instructions of the Engineer.

Job 2

2.22.02 4" galvanized for fire fighting system MR 10

2.22.03 2" galvanized for water system MR 10

2.22.04 2" galvanized for drain MR 10

2.22.05 4" galvanized for test line MR 10

2.22.06 2" galvanized for overflow MR 10

2.22.07 2" galvanized for main line MR 10

2.22.08 4" galvanized for main line MR 10







Fire Fighting Works

2.23 Sprinklers

2.23.01Supply and install upright sprinklers for the garages as shown

in drawings and specifications.No 134

2.24 MAV

2.24.01Supply and install main alarm valve diameter 4"as shown in

drawings and specifications.No 1

2.25 ZAV

2.25.01Supply and install zone alarm valve diameter 4"as shown in

drawings and specifications.No 2

2.26 Powder Extinguisher

2.26.01

Supply and install Portable Fire Extinguisher of 3Kg. powder

capacity each in Location as decided by the Engineer. The

installation shall be complete with brackets and it should be in

accordance with the Civil Defense specification.

No 37

2.26.02 Ditto but 6kg No 36

2.27 CO2 Extinguisher

2.27.01

Supply and install Portable Fire Extinguisher of 2Kg. co2

capacity each in Location as decided by the Engineer. The

installation shall be complete with brackets and it should be in

accordance with the Civil Defense specification.

No 15

2.28 Fire Pipes

2.28.01

Supply and install and commissioning of galvanized steel

(schedule40) 1" inch for fire cabinet including all required

sleeves, gate valves, check valves, strainers, rubber pressure

regulators, automatic air vents, drain cocks, elbows, T, with all

necessary fittings and connections .All is according to drawings

and specifications.

MR 500

2.28.02 Ditto but 11/4" MR 40

2.28.03 Ditto but 11/2" MR 40

2.28.04 Ditto but 2" MR 40

2.28.05 Ditto but 21/2" MR 350

2.28.06 Ditto but 3" MR 40

2.28.07 Ditto but 4" MR 250







2.29 Fire Cabinet

2.29.01

Supply and install 80*120*30 cm steel fire hose reel cabinet

2mm .The cabinet should includes 2*15m hose,2" nozzle, hose

reel of 1" diameter *25mm rubber hose with nossele,6kg

powder fire extinguisher,1" ball valve ,2" ball valve, and landing

valve. All according to drawings and specifications.

No 15

2.30 Siamese Connection

2.30.01Supply and install Siamese connection with two coupling of

65mm as shown in drawings and specifications.No 2

2.31 FM200

2.31.01

Supply and install FM200 system composed of 7KGfor

electrical DB with 5 smoke detectors&5 heat detectors with 5

nozzles. The price includes the pipes between the cylinder and

the nozzles, the release control panel ,abort switch ,control

panel includes dialer and all needed to complete the job. All is

according to ULFM.

LS 1

2.31.02Ditto but 45kg with 1 smoke and 1 nozzles and 1 heat detectors

for server roomLS 1

2.31.03Ditto but 70kg with 1 smoke and 1 nozzles and 1 heat

detectors for out archive in first floor.LS 1

2.31.04Ditto but 40kg with 1 smoke and 1 nozzles and 1 heat

detectors in in archive in first floorLS 1

2.31.05Ditto but 85kg of number 2 each 2 smoke and 2 nozzles and 2

heat detectors for the archive.LS 4

HVAC Works

Section10401-10600

2.32 Duct

2.32.01

Supply, install galvanized air duct of varies thickness as

required by SMACNA , the price including hanging, digging,

wooden sleeves or frames around duct passing through walls,

splitter dampers and volume dampers, and flexible connection

where needed and all fittings.

M2 1900

2.33 FANS

2.33.01 Exf-1 No 2

2.33.02 Exf-2 No 2

2.33.03 Exf-3 No 1

2.33.04 Exf-4 No 1

2.33.05 Exf-5 No 3

2.33.06 Exf-6 No 1

2.33.07 Exf-7 No 1

2.33.08 Exf-8 No 1

2.33.09 Exf-9 No 1







2.34 Close Control Unit(Provisional)

2.34.01

Supply and install close control unit of 4ton, with temperature

and humidity control with two circuits , complete with alarm

signaling system, programming of restart after power is

restored, remote unit switch ON/OFF, the price includes

condensate drain pump, humidifier condensate pump, fire and

smoke detectors, water leak detector Complete with electrical

connections, remote control, drain pipes up to floor drains,

supports, builders work copper pipes, cables and auto dialer

with the connection with the network.

No 2

2.35 Split units

2.35.01

Supply, install, and commissioning split air conditioning unit

1.5ton (heat pump)with R407 refrigerant gas, wall mounted

type. Complete with electrical connections, remote control,

drain pipes up to floor drains, supports, builders work copper

pipes, cables, complete.

No 2

2.36 Pre insulated duct

2.36.01

Supply and install pre insulated duct UL LISTED as per

drawings and specifications. The price shall include volume

dampers, splitter dampers, fire dampers, price shall also

include flexible connections where needed and all fittings and

accessories required to complete the job, all as per drawings,

specifications and the approval of the Engineer.

M2 3200

2.36.02GI sheet metal cladding of minimum 0.6 mm for duct on roof

and where needed.M2 250

2.37 Air curtain

2.37.01Supply and install concealed air curtain width 90cm as shown

in drawings and specifications.No 6

2.38 Grill

2.38.01

Supply, install, and commission white anodized 4 –WAY

aluminum grills and diffusers, complete with O.B, damper, all

with registers ceiling mounted. The price includes the

connection between the duct and the grill.

2.38.02 9"*9" No 152

2.38.03 12"*12" No 228

2.38.04 15"*15" No 15

2.38.05 linear width 10cm 2 slot m 85

2.38.06 Ditto but wall side 18"*9" No 25

2.38.07 Ditto but return 9"*9" No 25





2.38.12 Ditto but linear 2 slot,10cm width m 85

2.38.13 Ditto but with register18"*12" No 15

2.38.14 Ditto but with register12"*15" No 10

2.38.15 linear width 10cm 2 slot m 25

2.38.16 15"*15" but with register No 8

2.38.17 6"*6" but with register No 80







2.39 Chillers

Supply and install chiller in compliance with the specifications

and as shown in drawings, including concrete pedestals, corck

pads, and spring actuated shock absorbers as per the

manufacturer's recommendation

No 2

2.40 Fan coil

2.40.01

Supply and install fan coil unit as in drawings. The price

includes all fittings needed to complete the job. The price also

includes digital thermostat, power & control cable, drain pipes

to nearest riser or floor drain. The price includes the 2" UPVC

riser in walls.

2.40.02 FCU1-LL1 No 2

2.40.03 FCU2-LL1 No 1

2.40.04 FCU3-LL1 No 1

2.40.05 FCU1-LL2 No 1

2.40.06 FCU2-LL2 No 2

2.40.07 FCU3-LL2 No 1

2.40.08 FCU1-G No 2

2.40.09 FCU2-G No 1

2.40.10 FCU3-G No 1

2.40.11 FCU4-G No 1

2.40.12 FCU5-G No 2

2.40.13 FCU6-G No 1

2.40.14 FCU7-G No 1

2.40.15 FCU8-G No 1

2.40.16 FCU9-G No 6

2.40.17 FCU10-G No 1

2.40.18 FCU11-G No 2

2.40.19 FCU1-F No 1

2.40.20 FCU2-F No 2

2.40.21 FCU3-F No 1

2.40.22 FCU4-F No 1

2.40.23 FCU5-F No 1

2.40.24 FCU6-F No 1

2.40.25 FCU7-F No 1

2.40.26 FCU8-F No 1

2.40.27 FCU9-F No 1

2.40.28 FCU10-F No 1

2.40.29 FCU11-F No 1

2.40.30 FCU12-F No 1

2.40.31 FCU13-F No 1

2.40.32 FCU14-F No 1

2.40.33 FCU15-F No 1

2.40.34 FCU16-F No 2







2.40.35 FCU17-F No 2

2.40.36 FCU1-S No 1

2.40.37 FCU2-S No 1

2.40.38 FCU3-S No 1

2.40.39 FCU4-S No 1

2.40.40 FCU5-S No 1

2.40.41 FCU6-S No 1

2.40.42 FCU7-S No 1

2.40.43 FCU8-S No 1

2.40.44 FCU9-S No 2

2.40.45 FCU10-S No 1

2.40.46 FCU11-S No 1

2.40.47 FCU12-S No 1

2.40.48 FCU13-S No 1

2.40.49 FCU14-S No 1

2.40.50 FCU15-S No 1

2.40.51 FCU16-S No 1

2.40.52 FCU17-S No 2

2.40.53 FCU18-S No 1

2.40.54 FCU1-T No 1

2.40.55 FCU2-T No 1

2.40.56 FCU3-T No 1

2.40.57 FCU4-T No 1

2.40.58 FCU5-T No 1

2.40.59 FCU6-T No 1

2.40.60 FCU7-T No 1

2.40.61 FCU8-T No 1

2.40.62 FCU9-T No 1

2.40.63 FCU10-T No 1

2.40.64 FCU11-T No 2

2.40.65 FCU12-T No 1

2.40.66 FCU13-T No 1

2.40.67 FCU14-T No 1

2.40.68 FCU15-T No 2

2.40.69 FCU16-T No 1

2.40.70 FCU1-FO No 1

2.40.71 FCU2-FO No 1







2.40.72 FCU3-FO No 1

2.40.73 FCU4-FO No 1

2.40.74 FCU5-FO No 1

2.40.75 FCU6-FO No 1

2.40.76 FCU7-FO No 1

2.40.77 FCU8-FO No 1

2.40.78 FCU9-FO No 1

2.40.79 FCU10-FO No 1

2.40.80 FCU11-FO No 1

2.40.81 FCU1-FIF No 1

2.40.82 FCU2-FIF No 2

2.40.83 FCU3-FIF No 1

2.40.84 FCU4-FIF No 1

2.40.85 FCU5-FIF No 1

2.40.86 FCU6-FIF No 1

2.40.87 FCU7-FIF No 3

2.40.88 FCU8-FIF No 2

2.40.89 FCU9-FIF No 1

2.40.90 FCU1-SIX No 1

2.40.91 FCU2-SIX No 1

2.40.92 FCU3-SIX No 1

2.40.93 FCU4-SIX No 1

2.40.94 FCU5-SIX No 2

2.40.95 FCU6-SIX No 1

2.40.96 FCU7-SIX No 1

2.40.97 FCU8-SIX No 1

2.40.98 FCU9-SIX No 1

2.40.99 FCU1-SEV No 2

2.40.100 FCU2-SEV No 1

2.40.101 FCU3-SEV No 1

2.40.102 FCU4-SEV No 1

2.40.103 FCU5-SEV No 1

2.40.104 FCU6-SEV No 2

2.40.105 FCU7-SEV No 1

2.40.106 FCU8-SEV No 6

2.40.107 Air Handling Unit-1 (AHU-01) No 1









2.41 Black steel Pipes

Supply and install Black Steel of Schedule 40 pipes for heating

system, including all required insulation required thickness as in

specifications rolled by plastic bonds, sleeves, gate valves,

strainers, rubber expansion joint, regulating valves ,automatic

air vents, drain cocks with all required fittings and connections .

All is according to drawings, specifications and approval of the

Engineer. All pipes and fittings inside boiler room and shaft

should be insulated with rigid 2" fiber glass and 0.6mm

galvanized sheet metal cladding. (boiler room)and(roof)All is

according to drawings and specifications

2.41.01 3/4" MR 550

2.41.02 1" MR 400

2.41.03 11/4" MR 300

2.41.04 11/2" MR 300

2.41.05 2" MR 450

2.41.06 21/2" MR 300

2.41.07 3" MR 500

2.41.08 4" MR 300

2.41.09 6" MR 250

2.42 Pumps

2.42.01

Supply and install pumps. The price includes all fittings valves,

electrical cables, isolating switch, cable tray Control panel as in

drawings, specifications.

2.42.02 Sub-01pump NO 4

2.42.03 Sub-02 pump, alternating, the price includes four floats. LS 2

2.42.04 Sub-03 pump, alternating, the price includes four floats. LS 2

2.42.05CWBP with pressure transducer and the connection to the

control panel.LS 2

2.42.06 FJP,FDP,FEP(ULFM) (complete set as shown on drawings) LS 1

2.42.07 HWP-01 No 3

2.42.08 HWP-02 No 3

2.42.09 CHWP-01 No 4

2.42.10 CHWP-02 No 4

2.42.11 SHP-01 NO 1

2.42.12 SHP-02 NO 1

2.42.13 pp NO 2

2.43 Boilers

2.43.01

Supply, install, and commissioning steel boiler for heating

complete with burner concrete base, steel flue to main chimney

with painting and insulation, fuel filter, fuel valves, flexible,

expansion tank, fire valve, safety valve, flow switch, expansion

joints, two gate valves at inlet and outlet pipes, electrical

connections to the boiler room . For the boiler the price include

12-kg powder automatic extinguisher. The price is also includes

all piping with recommended thickness insulation and with 10

cm wide plastic bond, & fittings with valves inside boiler. All

according to drawings and specifications.

No 2







2.44 Fuel Tank

2.44.01

Supply, install, connect and test underground steel metal fuel

tank of 6 mm thickness sheet and 15,000 liter capacity with all

fittings and accessories, e.g. and not limited to gear pumps (a

set of two alternating pumps) of capacity as calculated by the

contractor and approved by the Engineer, and it's control and

accessories, inlets to the fuel tank, outlets, vents, a wall

mounted dial type and a dip stick type level indicators, including

all required valves, strainer, and connections, pipes of any type

and diameter and all related accessories between the filling

inlet (including quick coupling inlet, ball valve and check valve)

and the main fuel tank and pipes between the same tank and

the daily tank in the boiler room as shown on the drawings and

specifications. The tank shall also be coated with asphalt

coating as per the requirements of the Palestinian Petroleum

Authority, The price also includes the gear pumps with all their

control and power wiring and related ancillaries, excavation

works, reinforced concrete works such as base slab, walls,

cover slab, manhole, CI manhole cover of medium duty,

backfilling with sand all around and galvanized iron straps. all

as per drawings, specifications and Engineer's instructions.

No 1

2.44.02

Supply and install rectangular daily fuel tank 500 liters capacity,

consisting of heavy steel sheets 2 mm thick and of the

dimensions shown on the drawings, complete with 40X40 cm

cover, transparent level tube, mechanical float valve, angle

steel support stand, built in vent and drain outlet, overflow

outlet, main copper pipes feeding the burners, all as shown in

the drawings, specifications and the approval of the Engineer.

No 1

2.45 Chimney

2.45.01

Steel chimney 22” diameter, 4mm thick for heating & hot water

boilers, the price includes all flue sections in room, fittings,

supports, hangers, cleanout, etcH., plus the horizontal steel

section between boilers and shaft.

Height up to 1.5m above roof parapet, price includes insulation

with 2” rock wool insulation, and by 0.6mm G.I. sheet metal

gladding.

Fixing of chimney to wall shall be through flexible rings to avoid

transmission of noise to rooms, the weight of chimney shall be

carried by the bottom only, all according to drawings and

specifications.

MR 60

2.46 Dbboiler

2.46.01 Supply and install DB for boiler as shown in drawings. LS 1

2.47 DbChiller

2.47.01 Supply and install DB for chiller as shown in drawings. LS 2

2.48 Commissioning

2.48.01

Test and commission by a certified third party(s) for fire fighting

and HVAC systems according to NFPA and ASHRAE

standards and requirements.

LS 1

Total of Mechanical Works to be Carried To Main Summary





DIVISION 3 - ELECTRICAL WORK

Preamble:

-

This BOQ shall be read in conjunction with parts of the

electrical technical specifications, general and particular,

JEDCO requirements and electrical drawings except where

otherwise indicated.

-

The unit price for all items in all sections shall include the

supplying, installation, and commissioning unless otherwise

specially mentioned.

-The price shall also include the submittal of shop drawings and

as-built drawings in both hard copies and soft copies.

-All civil and finishing works related to the concerned item shall

be included in the unit price, unless otherwise indicated.

-

The contactor must submit two options from the trade markets

for each equipment according to the approved manufacturer

list outlined under the technical specifications.

-

All submittals should be genuine type therefore the contractor is

obliged to submit the source certificate for each supplied

equipment for approval from the supervising team.

3.1 Main Distribution boards

Supply, install, test and commission complete main distribution

board, type tested, according to IEC439-1, IP-31, inclusive of

all circuit breakers for outgoing and incoming cables, bus bars

and their coupling unit, casing spaces for cables, cable clamps/

terminals, cable shoes, protection equipment, as required to

form a complete unit. All shall be in accordance with the

drawings, specification, and the codes of practice and highest

prevailing standards of engineering.

The main distribution boards must be manufactured in

conformance to standard IEC 60439-1 and must be tested

according to the 10 tests defined by this international standard

of LV electrical switch gear assemblies.

3.1.1 MDB1 L.S 1

3.1.2 MDB2 L.S 1

3.1.3 Bus coupler panel 1000A L.S 1

3.2 Power Factor Panel:

Supply, install, test and commission a complete type tested

power factor panel inclusive of automatic power factor

controller, double insulated capacitor, cables, bus bars and

their coupling unit, casing spaces for cables, cable clamps/

terminals, cable shoes, protection equipment, as required to

form a complete unit.

All shall be in accordance with the drawings, specification, and

the codes of practice and highest prevailing standards of

engineering.

3.2.1 200 KVAR No 2







3.3 Sub-Main Distribution boards

Supply , install, test and commission electrical sub-main

distribution board type tested according to IEC439-1, IP-31, the

price include circuit breakers, basbars, terminals, wiring, bolts,

clamp and all internal components and connections as detailed

on drawings and technical specifications.

3.3.1 NDBL1+UDBL1+EDBL1 No 1


3.3.3 NDBGA+UDBGA+EDBGA No 1

3.3.4 NDBGB+UDBGB+EDBGB No 1

3.3.5 NDB1A+UDB1A+EDB1A No 1

3.3.6 NDB1B+UDB1B+EDB1B No 1








3.3.14 NDBL7+EDBL7 No 1

3.3.15 DB-LIFT1 No 1




3.3.19 DB-EX No 1

3.3.20 DB-EX2 No 1

3.3.21 DB/UPS-SERVER No 1

3.3.22 DB/AC No 1

3.3.23 ATS panel for fire pump 100A No 1

3.3.24 ATS panel for fire fighting lift 63A No 1

3.4 Control Panel

Supply, install, test and commission control panel include all

control cable between MDB and DB's, power supply, switches,

indication lamps and all accessories to complete the works as

drawings and technical specifications.

L.S 1







3.5 Electrical points

Supply, install, test and connect the following electrical outlets

and points, the price should include cables, conduits, sockets,

draw boxes, isolating switch, power cable to first point and all

accessories up to DB as per drawings and specifications.

3.5.1 3 pin single-phase, 16 Amp sockets in walls or tables No 460

3.5.2 Ditto, but weatherproof socket No 70

3.5.3 Ditto as item 1.5.1 but double socket No 310

3.5.4 Power point for electrical water heater No 60

3.5.5 Power point for extract fan No 10

3.5.6 Power point for access control panel No 45

3.5.7 Power point for server rack cabinet include cable 3x4mm2. No 10

3.5.8 3 pin single-phase 16 Amp UPS sockets in walls or tables No 40

3.5.9 Ditto, double socket No 280

3.5.10

3 phase combined socket outlet includes

- 1 socket, 3 Ph 25A

- 2 sockets, 1 Ph 16A

- Related circuit breakers

No 4

3.5.113 pin single-phase, 16 Amp sockets for A/C with isolating switch

and indication lamp.No 160

3.5.12Automatic operated infra red hand dryer 2000 watt, UL

approved stainless steel.No 41

3.5.13 Thermostat point include conduits and box No 140

3.5.141phase 16A isolating switch, IP-65 include cable 3x2.5mm2

XLPE cableNo 6

3.5.153phase 16A isolating switch, IP-65 include cable 5x2.5mm2

XLPE cableNo 5

3.5.163phase 20A isolating switch, IP-65 include cable 5x4mm2

XLPE cableNo 4

3.5.17 3phase 25A isolating switch, IP-65 (not include cable) No 3

3.5.18 Floor box 16 modules with cover No 20







3.6 Cables

Supply, install, test and commission, the following CU/XLPE

cables, rate include cables, conduits, ducts, galvanized trunk,

boxes, connection cable at both sides and all accessories

needed to connect and test the cables between appropriate

distribution boards. All as drawings and technical specifications.

3.6.1 5X6mm2 MR 70

3.6.2 5X10mm2 MR 2,600

3.6.3 5X16mm2 MR 800

3.6.4 4X25+16mm2 MR 200

3.6.5 4X35+16mm2 MR 100

3.6.6 4X185+95mm2 MR 800

3.6.7 4X240+120mm2 MR 80

3.6.8 1X240 mm2 MR 350

3.6.9 3X6mm2 MR 60

3.6.10 4X25+16mm2 fire resistance cable class A for 1.5h MR 60

3.6.11 5X16mm2 fire resistance cable class A for 1.5h MR 70

3.7 Cable Trays

Supply, install and connect covered perforated cable tray hot-

dip galvanized steel include mounting bracket, tee, bend, strait

connector barrier strip and all accessories as per drawings and

specifications.

3.7.1 20 cm width MR 650

3.7.2 30 cm width MR 50

3.7.3 40 cm width MR 35

3.7.4 60 cm width MR 20

3.7.5 10cm width with sun shade cover MR 50

3.7.6 20 cm width with sun shade cover MR 50

3.7.7 60 cm width with sun shade cover MR 55

3.7.8 20 cm width with cover and painted with fire proof coating MR 60

3.8 Cable Ladder

Supply, install and connect Heavy vertical cable ladder hot-dip

galvanized steel include mounting bracket, tee, bend, strait

connector and all accessories as per drawings and

specifications.

3.8.1 90 cm width MR 160

3.8.2 60 cm width MR 100

3.9 Lighting points

Supply, install and connect lighting points including conduits,

fire proof conduits and cables up to the DB, galvanized trunk,

light switches, installation for all lighting fixtures, power cable to

first point and all accessories as per drawings and

specifications.

No 3,687







3.10 Lighting Fixtures

Supply, install and connect the following lighting fixtures

including HF electronic ballasts, lamps and all accessories as


3.10.1Type(F1):2X36W fluorescent lighting fixture surface mounted

with polycarbonate body and polycarbonate diffuser, IP-65.No 100

3.10.2

Type(F1E):ditto as (F1), but with an emergency lighting

maintained for 1x36w for a duration of 3hr. Complete with

control, batteries and charger.

No 30

3.10.3

Type(F2):4X18W fluorescent lighting fixture recessed in false

ceiling with HF electronic ballast and galvanized steel stove

sheet body and double parabolic in matt aluminum, anti glare

and anti iridescence Louvre with outside port for ease

connection, IP20.

No 600

3.10.4

Type (F2*) 4x14W recessed light fixture with steel sheet and

internal white reflector housing and double parabolic high gloss

99.99 aluminum Louvre with PVD treatment to improve

luminous efficiency.

No 10

3.10.5

Type(F2E):ditto as (F2) & (F2*), but with an emergency lighting

maintained for 1x18w or 1x14w for a duration of 3hr. Complete

with control, batteries and charger.

No 200

3.10.6

Type(F3):2X18w compact fluorescent lighting fixture surface

mounted square shape with HF electronic ballast and vandal

resistant UV stabilized anti yellowing polycarbonate housing

and high gloss aluminum reflector and vandal resistant

polycarbonate dustproof diffuser IP44.

No 35

3.10.7




No 28

3.10.8

Type(F4):1x26w compact fluorescent lighting fixture wall

mounted with polycarbonate housing and polycarbonate

diffuser IP65

No 8

3.10.9Type(F5):1X18w compact fluorescent lighting fixture wall

mounted with polycarbonate cover, IP65.No 47

3.10.10

Type (F6) 2x18w compact fluorescent lighting fixture recessed

in false ceiling with HF electronic ballast with self extinguishing

vandal resistant polycarbonate housing and polycarbonate opal

diffuser , IP44.

No 130

3.10.11



control, batteries and charger.No 20

3.10.12Type(F7):1x54W T5 fluorescent lighting fixture with steel sheet

body for indirect light,IP20. No 1,500

3.10.13Type(F8):1X24W T5 fluorescent lighting fixture with steel sheet

body for indirect light,IP20.No 40







3.10.14

Type(F9):4X18W fluorescent lighting fixture recessed in false

ceiling with HF electronic ballast with sheet steel body and opal

diffuser IP40

No 45

3.10.15

Type (F9*) 4X18W fluorescent lighting fixture recessed in false

ceiling with HF electronic ballast with sheet steel body and anti

glare prismatic diffuser IP40

No 5

3.10.16




No 16

3.10.17

Type(F10):2X26w compact fluorescent lighting fixture recessed

in false ceiling Square Shape with HF electronic ballast with

self extinguishing vandal resistant polycarbonate housing and

polycarbonate opal diffuser , IP44.

No 75

3.10.18




No 15

3.10.19

Type(F11):1X3w led light lighting fixture recessed in false

ceiling with square die-cast tama and polycarbonate diffuser,

IP20. including driver.

No 75

3.10.20Type (F11*) 3x3w led light lighting fixture recessed in false

ceiling with sheet steel housing IP43. including driver.No 10

3.10.21

Type(F12):2x18w compact fluorescent lighting fixture recessed

in false ceiling Square Shape with HF electronic ballast with self

extinguishing vandal resistant polycarbonate housing and


No 35

3.10.22




No 10

3.10.23

Type(F13)1x13w compact fluorescent lighting fixture recessed

in false ceiling Square Shape with HF electronic ballast with self

extinguishing vandal resistant polycarbonate housing and


No 300

3.10.24




No 75







3.10.25Type(F14):1X35w halogen 24v light fixture with die-cast

aluminum body and brushed aluminum finish, IP20. No 25

3.10.26

Type(F15):1X26w compact fluorescent surface mounted down

light with aluminum body, die cast aluminum bezel and glass

diffuser, IP-65.

No 24

3.10.27Type(F16):1x50 suspended lighting fixture conical body with

polycarbonate diffuser, IP-20. (Decorative type)No 10

3.10.28

Type(F17):wall mounted exit light, maintained 1x8w fluorescent

tube for a duration of 3hr. complete with control batteries and

charger with steel body and polycarbonate cover, IP20.

No 31

3.10.29

Type(F18):suspended exit light, maintained 1x8w fluorescent

tube for a duration of 3hr. complete with control batteries and

charger with steel body and polycarbonate cover, IP20.

No 33

3.10.30

Type(F19):2x50w halogen grid lights suspended lighting fixture

vertical position with sardonic swivel system on two axis to

adjust 40 deg in all direction, with aluminum body, IP-20.

No 30







3.10.31

Type(F20):2x54w T5 fluorescent light & 2X50 halogen light

direct and indirect suspended lighting fixture with rectangular

frame with extruded aluminum housing and polycarbonate

smooth external finish diffuser with powder coated coating finish.

No 12

3.10.32




No 5

3.10.33Type(F21):75LED light per meter (6.6w/m) light indoor tube with

silicon modified pvc tube, IP40.MR 10

3.10.34

Type(F22) 6x4w white power led flood light ground mounted

with die cast aluminum body , and tempered shock and heat

resistant 4mm thick glass with power supply and controller, IP-

65.

No 8

3.10.35

Type(F23):4M brushed aluminum alloy cylindrical cone shape

section 180mm diameter base lighting column with pole top

light fixture of die cast aluminum housing and shatterproof and

self extinguishing polycarbonate diffuser 150W CDM-T IP65.

No 8

3.10.36

Type(F24):400w metal halide asymmetrical flood light with optic

to give extra wide distribution with die cast aluminum body and

4mm glass thick, with control gear, IP-65.

No 10

3.10.37Type(F25):2x7w compact fluorescent lighting fixture floor

recessed die cast aluminum body with frosted glass, IP-67.No 25

3.10.38Type(F26):1x150w CDM-T spot lighting fixture with adjustable

exterior flood light & tempered glass 4mm diffuser IP65.No 22

3.10.39

Type(F27):1x26w compact fluorescent lighting fixture in fibber

glass nylon housing with die cast aluminum frame and 4mm

tempered glass thick, IP-65.

No 10

3.10.40Type(F28):1x18w fluorescent lighting fixture decorative mirror

light, IP-65.No 25







3.11 Main Distribution Frame

Supply, install, test and commission main distribution frame for

main telephone feeder with all accessories needed for complete

work, as specified and as detailed on drawings .

L.S 1

3.12 Data Network Structure

Supply, install, test and commission network system complete

with air patch panel, patch core cable and all accessories

needed for complete work, as specified and as detailed on

drawings.

3.12.1Rack cabinet 12U with 2 fans and power strip 6outlet with

surge protection and slides shelfNo 13

3.12.2Rack cabinet 42U with fans and two power strip 6outlet with

surge protectionNo 3

3.12.3 RJ45 Cat6 patch panel 24 port No 45

3.12.4 Data socket include CAT6 STP cable from socket to patch panel No 800

3.12.5 12 Port fibber optic patch panel with connector No 30

3.12.6 4 port fibber optic cable multi mode MR 1,000

31.12.7 wireless LAN transmitter with POE No 27







3.13 Uninterruptible Power Supply(Provisional Item)

3.13.1

Supply, install and commission Uninterruptible power supply

(UPS) 160KVA modular type 3IN/3OUT with 8 number 20KVA

for each module & 1no. 20KVA spare , on-line Double

conversion with built in voltage regulator and harmonics filter .

Rate includes charger and rectifier(12pulse), static inverter,

Butteries (Hot Swap) and butteries rack for feeding registration

for 15 minutes operation at full load, true sine wave output with

less than 3% THD, crest factor not more than 3:1 and remote

monitoring unit & control with management software and all

accessories and test operation according to drawings and

specifications.

No 1

3.13.2

Supply, install and commission Uninterruptible power supply

(UPS) 30KVA modular type 3IN/3OUT with 3 number 10KVA

for each module & 1no. 10KVA spare , on-line Double

conversion with built in voltage regulator and harmonics filter .

Rate includes charger and rectifier(12pulse), static inverter,

Butteries (Hot Swap) and butteries rack for feeding registration

for 15 minutes operation at full load, true sine wave output with

less than 3% THD, crest factor not more than 3:1 and remote

monitoring unit & control with management software and all

accessories and test operation according to drawings and

specifications.

No 1

3.13.2

Supply, install and commission source transfer switch (STS)

30KVA connect two UPS. Rate includes fixing, rack and all

accessories with management software and all accessories

and test operation according to drawings and specifications.

No 1

3.14 SMATV system

Supply, install and commission SMATV system complete with

all internal connection, RG-6 cables, sockets, boxes , conduits

and main cables from each satellite to SMATV, splitters,

high/low frequency head, multi switcher, dish, receiving head

and all accessories needed for complete work according to


3.14.1 TV socket outlet 75 Ohm No 55

3.14.2 SMATV tap-off 4-way No 6

3.14.3 SMATV tap-off 4-way with end of line resistance No 7

3.14.4 SMATV tap-off 6-way No 4

3.14.5 SMATV tap-off 6-way with end of line resistance No 4

3.14.6 Head End Unit for 36 Channel |(PROVISIONAL ITEM) L.S 1

3.14.7 SMATV Splitter 4-way No 1

3.14.8 SMATV distribution amplifier No 10

3.15 Fire Alarm System

Supply , install , connect and commission addressable fire

alarm system, including all required works, conduits, cables(fire

resistance 2*1.5mm2), wires and fittings, according to drawings

and specifications.

3.15.1Fire alarm control panel 4 loops expandable with batteries and

charger & maintenance software.No 1







3.15.2 Analog addressable break glass unit including back box No 30

3.15.3 Analog addressable photo optical smoke detector No 390

3.15.4 Analog addressable heat detector No 45

3.15.5Analog addressable smoke beam detector include transmitter

and receiver.No 3

3.15.6 Analog addressable smoke duct detector No 2

3.15.7Audio-Visual electronic fire strobe with addressable interface

modular base.No 30

3.15.8Audio-Visual electronic fire strobe with addressable interface

modular base IP-65.No 5

3.15.9 Automatic dialer with speech processor ,24 V No 5

3.15.10 Short circuit isolator (SCI) No 30

3.15.11 Control module No 35

3.15.12 Door Magnetic lock for fire exit door No 5

3.15.13 Fire men telephone jack No 10

3.16 ACCESS CONTROL SYSTEM

Supply , install , connect and commission on line programmable

access control system, including all required works, conduits,

cables(fire resistance) , wires and fittings, according to

drawings and specifications

3.16.1

Command center PC server for access control system the price

include genuine software, hardware, PC device and all

accessories.

No 1

3.16.2

Access control controller with TCP/IP Ethernet network port for

doors include data point, CAT 6 cable, power supply, butteries

and charger.

No 35

3.16.3 Access control SMART Card Reader No 35

3.16.4 Door Magnetic lock No 35

3.16.5 Exit push button No 70

3.17 Intercom System

Supply , install , connect and commission Intercom system,

including all required works, conduits, cables, transformers,

wires and fittings, according to drawings and specifications

3.17.1 Indoor Intercom Unit No 35

3.17.2 Outdoor Intercom Unit No 35

3.18 First Fix for Projection System

Supply , install and connect first fix for projection system

including all required works, conduits, wires and fittings,

according to drawings and specifications

No 5

3.19 IP Monitoring Security System(Provisional Item)

Supply , install , Connect and Commission IP-Monitoring

Security System, including all required works, conduits, RJ45

outlets, CAT 6 cable, CAT 6 patch cables, software, rack to the

system and all fittings and accessories, according to drawings

and specifications







3.19.1

Media server high performance (The No. of servers depends

on the solution that will be submitted by the contractor) with 6

HD 1 Terra each, array storage expandable to 12, core 2

extreme CPU , 4 GB memory, professional monitor with

resolution 1280x800 or higher, 1G network card and graphics

card. The price including video management software, for

mention camera expandable. Server client base. View/record in

real time for all cameras simultaneously, fail over and

redundancy, IP intercom, view tampering, cameras encryption,

motion detector, maps and graphical presentation.

No 1

3.19.2

Fixed Dome Camera CMOS Image sensor, Image sensor size

1/3 “,Min illumination/ light sensitivity (Colour) 1 lux, Max video

resolution 640x480, Max frames per second 25, Lens Focal

length 2.8 - 10 mm, Aperture: 1.3, Compression Motion JPEG

and MPEG-4, Video motion detection, Audio detection, Active

tampering, Alarm inputs/outputs 1/1, QoS, Power over

Ethernet, Multi-level password, HTTPS encryption, IP address

filtering, IEEE 802.1X.

No 34

3.19.3

Box Camera CCD Image sensor, Image sensor size 1/3“,Min

illumination/ light sensitivity (Colour) 0.75 lummox video

resolution 640x480, Max frames per second 25, Lens Focal

length 3 - 8 mm, Aperture: 1.3, Compression Motion JPEG and

MPEG-4, Video motion detection, Audio detection, Alarm

inputs/outputs 1/1, QoS, Power over Ethernet, Multi-level

password, IP address filtering, IEEE 802.1X.

No 14

3.19.4

Outdoor Camera CCD Image sensor, Image sensor size 1/3”

,Min illumination/ light sensitivity (Colour) 0.65 lummox, Min

illumination/ light sensitivity (B/W) 0.08 Lox , Day and Night,

video resolution 640x480, Max frames per second 60, Lens

Focal length 10-40 IRE mm, Aperture: 1 Lens mount CS,

Compression Motion JPEG and MPEG-4, Video motion

detection, Alarm inputs/outputs 2/1, Multi-level password,

HTTPS encryption, Power over Ethernet, IP address filtering,

IEEE 802.1X. IP-66

No 8

3.19.5

Outdoor PTZ Camera CCD Image sensor, Image sensor size

1/3” “,Min illumination/ light sensitivity (Colour) 0.3 lox, Min

illumination/ light sensitivity (B/W) 0.005 lox, Day and Night,

video resolution 704x480/704x576, Max frames per second

30/25, Lens Focal length 4.1 - 73.8 mm, Aperture:1.4

Pan range: +/-360 endless, Tilt range: 180, Optical zoom: 36 ,

Digital zoom: 12, Compression Motion JPEG and MPEG-4,

Video motion detection, Alarm inputs/outputs 4/4, , Multi-level

password, HTTPS encryption, Power over Ethernet, IP address

filtering, IEEE 802.1X. IP-66

No 15

3.19.6

PTZ Joystick Control Durable high quality joystick, X/Y-axis for

positioning and turning handle for zoom, 12 programmable

push-buttons:2 on handle and 10 on base housing

No 1







3.19.7

Screen Size 40"

Resolution 1920x1080

Contrast Ratio 4000:01:00

Power Consumption 220W

Stand By Power(DPMS 1W(Energy Saving ON)

No 2

3.20 Public Address System

Supply, install and commission to obtain a complete system

and all necessary accessories, All equipment must be of the

same company and should be UL Approved, Program a

complete Voice Management System ( Integrated Public

Address / Voice Evacuation system ) including connections with

Fire alarm system and paging system, fire resistance cable, fire

proof conduits, boxes and all accessories needed to complete

system according to drawings and specifications

3.20.1

Sound system Main PA/voice evacuation rack equipped with

enough power amplifiers to handle the below mentioned

speakers, rack should Include monitoring panel, call station

,CD player, tuner, 3 microphone with stands & all accessories.

The system should also Include zoning capabilities ( zone mixer

) at least 16 Zones. The rack should Include all required

internal cabling, paging system, cooling fans , glass door with

lock.

No 1

3.20.2Recessed/Surface mounted loudspeaker 6w, 2-way round and

metal grill.No 130

3.20.3 Digital call station with 16 zones and priority with microphones No 4

3.21 Sound System For Meeting Hall (PROVISIONAL ITEM)

Supply, install, test and commission to obtain a complete

system and all necessary accessories, All equipment must be

of the same company and should be UL Approved, including all

accessories needed to complete system according to drawings

and specifications

3.21.1

Sound system rack equipped with enough power amplifiers to

handle the below mentioned speakers, rack should Include

monitoring panel ,CD player, tuner& all accessories. The

system should also Include zoning capabilities ( zone mixer ) at

least 2 Zones. The rack should Include all required internal

cabling, cooling fans , glass door with lock.

No 1


metal grill.No 8

3.21.3handheld unidirectional dynamic wireless

microphone/transmitter/receiver No 3

3.21.4 Subcardioid Dynamic Console Gooseneck Microphone No 2

3.21.5Presenter wireless with lavaliere microphone

/transmitter/receiver No 3







3.22 Sound System For News Room (PROVISIONAL ITEM)





and specifications

3.22.1



monitoring panel ,CD player, tuner& all accessories. The

system should also Include zoning capabilities ( zone mixer ) at

least 2 Zones. The rack should Include all required internal

cabling, cooling fans , glass door with lock.

No 1


metal grill.No 4

3.22.3handheld unidirectional dynamic wireless

microphone/transmitter/receiver No 2

3.22.4 Sub cardioid Dynamic Console Gooseneck Microphone No 2

3.22.5Presenter wireless with lavaliere microphone

/transmitter/receiver No 2

3.23 Sound system for Cafeteria (PROVISIONAL ITEM)





and specifications

3.23.1



monitoring panel ,CD player, tuner, 3 microphone with stands

& all accessories. The system should also Include zoning

capabilities ( zone mixer ) at least 3 Zones. The rack should

Include all required internal cabling, cooling fans , glass door

with lock.

No 1


metal grill.No 15

3.23.3 Microphone socket include conduits and cables No 1

3.24Digital Infra-red Language Distribution System

(PROVISIONAL ITEM)

Supply , install , Connect and Commission digital infra-red

language distribution system, including all required works,

conduits, software, rack to the system and all fittings charger

case storage case and accessories, compliant to IEC 61603-7

and IEC 60914 according to drawings and specifications

3.24.1

Digital Infra-red Transmitter capable of distribution 4 channels

with LCD display and configuration menu AND 4BNC output

connector for HF signal for radiators 1BNC connector for

receiving and Ethernet connection.

No 1







3.24.2Digital Infra-red Radiator 15w(30m) with moveable angle,

automatic gain control and delay compensation.No 2

3.24.3

Digital Infra-red Receiver with 4 channel selection, LCD display,

adjustable volume and single earphone with stereo plug and

rechargeable cell.

No 50

3.24.4

Simultaneous 12 ch dual Interpreter Unit with select Kay,

microphone, headphone jack, built in speaker and volume

controller.

No 2

3.24.5 Interpreter mic/headset No 4

3.24.6 Carrying, Charging case for 50 IR Receiver. No 1

3.25 Digital Discussion System (PROVISIONAL ITEM)

Supply , install , Connect and Commission digital discussion

conference system, including all required works, conduits,

software, rack to the system and all fittings racks, and

accessories, compliant to IEC 60914 according to drawings and

specifications

3.25.2Main control unit with power supply, automatic audio equalizer

and Ethernet connection.No 2

3.25.3 Chairman contribution unit with loudspeaker No 2

3.25.4 Delegate contribution unit with loudspeaker No 45

3.26 Earthing system

3.26.1

Supply , install, test and commission earthing system for the

building the price include rods, earth wires, earthing pits,

inspection manholes 20*20*20cm(Three set for MDB1, MDB2 &

TRANSFORMER ROOM) loop earth cable FOR ALL

BUILDING, earth busbar, connect foundation earth with main

basbars )earth resistance must be less than 1.0 Ohm) and all

accessories as shown on drawings and code of practice.

L.S 1

3.26.2

Supply , install and commission earthing system for server

room the price include rods, earth wires, earthing pits,

inspection manholes 20*20*20cm loop earth cable, earth

busbar and all accessories as shown on drawings,

specification, and code of practice.

L.S 1

3.26.3

Supply , install, test and commission earthing all mechanical

equipment, steel structure, false ceiling, curtain wall, recessed

floor, cable tray, metal pipe, power panel and the price include

earthing wires, busbars, connection and all accessories to

complete the work according to specification, drawings and

code of practice.

L.S 1







3.27 Power Manhole

Supply, install, connect, and construct 100x100x100 cm

electrical manholes including heavy-duty cast iron cover 25Ton,

UPVC conduits & pipes, excavation, backfilling and all civil

works need to complete the work as Shown on drawings,

specifications and engineer approval.

No 5

3.28 Telephone Manhole

Supply, install, connect, and construct 80x80x80 cm telephone

manholes including heavy-duty cast iron 25Ton cover, UPVC

conduits & pipes, excavation, backfilling and all civil works need

to complete the work as Shown on drawings, specifications

and engineer approval.

No 3

3.29 Lightning protection system

Supply, install, test, and commissioning lightning protection

including lightning arrestor 5 meter height with level of

protection I and 25m radios of protection, isolated 2 NO. down

cable Ø70mm2, earthing pit and all accessories, needed to

complete work as specifications, drawings.

L.S 1

3.30 Stand by diesel Generator

Supply, install, test and commission stand by diesel generator

set (630KVA) , speed 1500rpm heavy duty industrial turbo

charger engine with control panel and all equipment as

specified and as shown on the drawings including of all

equipment, cooling system for diesel and tools set including

radiator and cooling fan complete with protection guards ,

exhaust from engines. 24 volt, system with battery charging

alternator, starter motor , permanent magnet pilot exciter

followed by main exciter, batteries and battery rack mounted on

machine base frame and with static battery charger, and

original sound proof canopy (70dB @7m) water proof, and all

controls including voltmeter, voltmeter phase selector 7

position, ammeter , ammeter selector with 4 position, frequency

meter, hours run meter, battery voltmeter, coolant temperature

gauge, oil pressure gauge and tools set required to provide an

installer which is complete and a full set of operation and

maintenance manuals in English. Price to include concrete

base with reinforcement as per engineer instructions , control

cable, earthing system for generator

L.S 1

chimney, 1000L daily tank for generator with pump, 12KG

powder automatic extinguisher and all accessories to complete

the work according to specification & drawings.







3.31 First Fix for Sound System (PROVISIONAL ITEM)

Supply , install and connect first fix for sound system including

all required works, conduits, boxes and fittings, according to

drawings and specifications

No 3

3.32First Fix for Digital Infra-red Language Distribution System

(PROVISIONAL ITEM)

Supply , install and connect first fix for Digital Infra-red

Language Distribution system including all required works,

conduits, boxes and fittings, according to drawings and

specifications

No 1

3.33First Fix for Digital Discussion System (PROVISIONAL

ITEM)

Supply , install and connect first fix for Digital Infra-red

Language Discussion system including all required works,

conduits, boxes and fittings, according to drawings and

specifications

No 2

3.34

Supply and install galvanized steel cover for electrical trenches

width 80cm the price includes all need accessories to complete

the works according to drawings, specifications and

engineering instructions.

MR 50

3.35

Supply and install galvanized steel grounding for electrical shaft

(230cm X 100cm) and the thickness 5cm the price includes all

need accessories to complete the works according to drawings,

specifications and engineering instructions.

No 11

Total of Electrical Works To be carried to the main

summary




Division

1 Finishing Works

2 Mechanical Works

3 Electrical Works

Signature & Stamp :

Date:

Currency of Bid (NIS or USD) : ______________

MoFA Package 2

Finishing, Mechanical and Electrical Works

Summary

Item

Grand Total (including provisional items)

- Excluding Value Added Tax (VAT)

Authorized Person Name & Title :

Total

Total In words:

Name of Contractor / Joint Venture:


Date post:	21-Jan-2017
Category:	Documents
Upload:	hoangdung
View:	218 times
Download:	1 times

final BoQ 2.11.11.xlsx

Documents