Published 06/12

DISCMOWER

HMG7, HMG8, HMG9, HMG10Disc Mower

PARTS MANUALSECTION 94

Important Operatingand Safety Instructionsare found in the MowerSafety Video that canbe instantly accessedon the internet at:www.algqr.com/bve

An Operator’s Manual was shipped with the equipment. The Operator’s Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator’s Manual is not with the equipment, contact your dealer or Bush Hog to obtain a copy before operating the equipment.

©2009 Alamo Group Inc.

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in pro-cessing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organiza-tion ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.Direct any questions regarding parts to:

BUSH HOG2501 Griffin Ave. Selma, AL 36703www.bushhog.comContact Us800-304-2836

INDEXHMG7, HMG8, HMG9, HMG10 DISC MOWER

CONTENTS PAGECurtain, Frame & Swath Board Assembly, HMG7,HMG8, HMG9, HMG10 . . . . . . . . . . . . .94-1-14Cutter Disc,Knives,Gearsets,& Related Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-5Cutter Bar Assembly & Related Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-2Decals- Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-16Decals - Pictorials (Part 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-17Decals - Pictorials (Part 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-18Drive Belts, Shields, Frame Support & Related Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-12Driveline, HMG7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-10Driveline, HMG8, HMG9, HMG10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-11Gearbox Assembly & Related Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-6Kits, Anti-wear Skid Plate & Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-20Kit, Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-20Kit, 3 Blade Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-20Main Frame, Hitch & Related Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-8Table of Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-1-1

TABLE OF CONTENTFOR

BUSH HOG HMG7, HMG8, HMG9, HMG10HAY MOWER PARTS

(94-1-2) CUTTER BAR ASSEMBLY AND RELATED PARTS(94-1-4) CUTTER DISC, KNIVES GEAR SETS AND RELATED PARTS(94-1-6) GEARBOX AND RELATED PARTS

(94-1-8)MAINFRAME HITCH

AND RELATEDPARTS

(94-1-12) DRIVE BELTS, SHIELDS,FRAME SUPPORT & RELATED

PARTS

(94-1-14) CURTAIN, FRAME, SWATHBOARD & RELATED PARTS

94-1-1

CUTTER BAR ASSEMBLY AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

“The asymmetrical plate goesunder the first disc near the gear-box on the even machines (6 and8 discs) and under the first 2 discsnear the gearbox on odd machines(5 and 7 discs)”

94-1-2

32

1

Ref. Part No. Description QuantityHMG7 HMG8 HMG9 HMG10

1 00787119 Complete Gearbox 12 00788130 Free Wheel Z36 Group 5 2 5 23 N/A Disc With Drum With Convoy Group 24 N/A Disc Group 3 4 5 65 00788131 Free Wheel Z45 Group 6 10 10 146 00787340 Special Screw M10x25 27 33 39 457 00787192 Oil Cap 3/8 Gas 3/8 Gas Thread 28 38028C Copper Washer 3/8" 39 00787339 Special Screw M10x35 21 23 25 2710 00787175 Tub Cover 1856x245 SP8 1 0 0 0

00787176 Tub Cover 2150x245 SP8 0 1 0 000787177 Tub Cover 2512x245 SP8 0 0 1 000787178 Tub Cover 2806x245 SP8 0 0 0 1

11 00787179 Tub Bottom 1856x215x38 1 0 0 000787180 Tub Bottom 2150x215x38 0 1 0 000787181 Tub Bottom 2512x215x38 0 0 1 000787182 Tub Bottom 2806x215x38 0 0 0 1

12 00787344 Hexagonal Nut M10 Din 934 - Iso 4032 M10 58 68 78 8813 00787190 Symmetrical Slide Plate - Skid 350x45x378 3 5 5 714 00787183 Support Brace 512x455x35 SP8 115 701512C Washer, Flat M10 Uni 6592 - Iso 7089 M10 5 6 7 816 00787189 Asymmetrical Slide Plate - Skid 350x45x378 2 1 2 117 00787191 Spacer Bushing D-Ext16 D-Int11 L20 5 6 7 818 00787188 Internal Slide Plate 568x220x210 SP6 119 00787341 Special Screw M10x 65 5 6 7 820 00756026 Screw M12x35 Din 931 - Iso 4014 M12x35 221 701513C Washer, Flat M12 222 701112C Self locking Nut M12 223 02967532 Socket Hd. Cap Screw M8x25 424 00788177 Oil Cap 3/8 Gas Thread With Bar 1

CUTTER BAR ASSEMBLY AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-3

CUTTER DISC, KNIVES GEARSETS AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-4

Ref. Part No. Description QuantityHMG7 HMG8 HMG9 HMG10

1 00787342 Special Screw M20x30 11 12 15 162 00787184 Bush Hold Bearing D_Ext40.05 L32.5 11 12 15 163 00787343 Washer Din 988 42x52x2.5 11 12 15 164 00772851 Bearing 6208 N 40x80x18 11 12 15 165 00753224 Internal Retaining Uni 7437 Din 472 D80 11 12 15 166 00787187 Free Gear Z=36 D_Ext117 D_Int80 L16 11 12 15 167 00787186 Special Nut M20x2.5 11 12 15 168 00787185 Free Gear Z45 D_Ext143.4 D_Int80 L16 6 10 10 149 00787163 Plastic Cap D91l11 With Collar D100 210 00787337 Special Flange Screw M10x25 30 36 42 4811 00787338 Exagonal Nut M12, With Flange 10 12 14 1612 00787173 Disc Flange Cover D120 L29.5 3 4 5 613 00787164 Disc With Drum With Convoy 214 00787174 Disc 400x240x39 3 4 5 615 00787166 Right Knife 40x108 Sp4 6 6 8 815 00787167 Left Knife 40x108 Sp4 4 6 6 816 00787168 Screw For Knife M12x15 10 12 14 1617 701127C Selflocking Nut M20x1.5 5 6 7 818 00788132 Cup Spring M20 5 6 7 819 00787165 Grooved Disc Flange 5 6 7 820 00770102 Bearing 6306-2rs1/C3 5 6 7 821 00787344 Hexagonal Nut M10 20 24 28 3222 00787169 Bearing Support Flange 5 6 7 823 00787339 Special Screw 20 24 28 3224 00787170 Spacer Bushing 5 6 7 825 00787171 Ring Or 5 6 7 826 00752923 Oil Seal 40x56x8 5 6 7 827 00788133 Bearing 6306-2z/C3 5 6 7 828 00787172 Rotor Gear With Shaft Z=34 5 6 7 8

D-Ext102 L100 Grooved Shaft

CUTTER DISC, KNIVES GEARSETS AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-5

GEARBOX AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-6

GEARBOX AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

Ref. Part No. Description QuantityHMG7 HMG8 HMG9 HMG10

1 00787140 Oil Vent Cap 3/8 Gas Thread With Bar 12 38028C Copper Washer 3/8" 23 N/A Gearbox Housing 14 00787141 Conical Crown Z20 15 710840 Key 16 00787138 Transmission Shaft 17 710850 Key 18 00754459 Bearing 29 00787135 Ring Or 110 00787136 Or Bushing 111 00787137 Cover Flange 212 3236801 Oil Seal 45x72x10 113 00787129 Plastic Bushing 214 00751688 Screw M10x25 1615 701112C Selflocking Nut M12 816 00788134 Tab Washer With Long Tab 417 00787142 Pinion With Shaft Z9 118 00787114 Bearing 119 3238201 External Retaining 120 00753224 Internal Retaining 221 00787143 Seal Ring 35x80x10 122 00765702 External Retaining 123 00786146 Internal Retaining 124 61075C8 Screw M12x60 825 00788135 Lower Bolt-Lock Plate 126 00788136 Reinforcement Plate 127 00787139 Fluted Gear 128 00787145 Ring Or 129 00787144 Bush Hold Bearing 130 00764417 Bearing 131 00788137 Upper Bolt-Lock Plate 132 00772827 Stopper Vent Oil 3/8 Gas 133 00787345 H.S.B.H.S. Screw m10x25 234 001724 Oil Seal 35x72x10 1

94-1-7

MAINFRAME HITCH AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-8

MAINFRAME HITCH AND RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

Ref. Part No. Description QuantityHMG7 HMG8 HMG9 HMG10

1 00787076 Plastic Cap 12 00787077 Cylinder Attachment Pin 13 703516W Spring Pin 44 8382 Grease Nipple M8x1 35 701127C Selflocking Nut M22 (Nylon Insert) 16 00776217 Washer, Flat M24 37 00787079 Spacer Bushing 28 00787089 Turnbuckle Support 19 00787080 Headgear Attachment 110 00787082 Pin For Headgear 111 00787104 Spacer 112 00787081 Plastic Bushing 313 001465 Grease Nipple M6x1 114 00787091 Hydraulic Cylinder 115 00788138 Washer m48 x 30 x 2 416 00787328 Washer, Thin 217 00787098 Plastic Bushing 218 00751693 Screw M8x16 219 701511C Washer, Flat M8 220 00776031 Manual Canister 121 50069777 Manual 122 701111C Selflocking Nut M10 123 00787346 H.S.B.H.S. Screw M10x30 124 00788139 Connector Support Plate 125 00788140 Female Hydraulic Connector 126 00788141 Click Pin For Tube 227 3638401 Hair Pin Cotter 128 00787093 Pin For 3pt 129 00787130 Zinc Cricket 130 00787092 3 Point Frame 131 00787096 Lower Link Pin 232 00787099 Hydrauilic Rubber Pipe Kit 133 703615W Spring Pin 234 00787127 Chain Attachment 135 00787102 Knurl For Rope 136 00787101 Rope 137 00787100 Rope Clamp 138 00787097 Stand 139 00788142 Click Pin 140 00787095 Joint For Attachment To Frame 141 00787086 Ball-End Socket Joint Attachment Pin 142 70497 Cotter Pin 6.3x50 143 00787094 Pin For Lifting System Attachment 144 00787088 Short Plastic Bushing 145 00765692 Screw M14x50 146 00755940 Washer, Flat M14 247 00787105 Lever For Uncoupling 148 00787103 Knob For Uncoupling Lever 149 701113C Selflocking Nut M14 150 00787087 Spring For Lightening Lifting System 151 00788143 Connecting Rod With Eyelet M12 X 110 152 701112C Nut With Milled Flange M12 253 00787078 Bushing For Sup. Turnbuckle St 154 701115C Selflocking Nut M18 155 701516C Washer, Flat M18 156 00787083 Turnbuckle Staff 157 00787085 Spring For Turnbuckle Staff 158 00787084 Turnbuckle Staff Cover 159 00787335 Spring Pin 160 701520C Washer, Flat M27 461 00787217 Driveshaft Assembly HMG7 1 0 0 0

00787351 Driveshaft Assembly HMG8, HMG9, HMG10 0 1 1 1

94-1-9

REF. PARTNO. NO. DESCRIPTION QTY.

1 00787217 Assy Driveline -540 rpm 1- 00787523 Assy, QD Yoke 1- 00787524 Kit, Push Pin 1- 00787525 Kit, Bearing Cross 2- 00786708 Yoke, Outer Tube 1- 703518W M8 x 60 Roll Pin 1- 703517W M8 x 55 Roll Pin 1- 00786709 Yoke, Inner Tube 1- 00787526 Assy, Clutch - Free Wheel 1- 00787527 Assy, D/L Safety Shield - Complete 1- 00756005 Decal, Rotating Driveline 1- 00756004 Decal, Danger - Guard Missing 1

DRIVELINE ASSEMBLYBUSH HOG HMG7

HAY MOWER

94-1-10

REF. PARTNO. NO. DESCRIPTION QTY.

1 00787351 Assy Driveline -540 rpm 1- 00761442 Assy-QD Yoke 1-3/8-6 1- 00754474 Push Pin Set B-P #40 1- 00759119 Yoke-Collar & Snap Ring 1- 00759515 Retaining Ring 1- 00764500A Assy, Yoke Collar-Complete 1- ------ Spring, QD Pin 1- ------ Pin, QD 1- 00774079 Kit, Slide Collar Repair 1- 00761438 Assy-Cross Bearing SER 5 EG# 2- 00787528 Yoke, Outer Tube 1- 703624W M10 x 75 Roll Pin 1- 00762581 Yoke, Inner Tube S50 1- 00787529 Assy, Clutch-Free Wheel 1- 703623W M10 x 65 Roll Pin 1- 00769298 Shield, D/L Outer For 00766850 1- 00766228 Junction Ring 1- 00756005 Decal, Rotating Driveline 1- 00756004 Decal, Danger-Guard Missing 1

DRIVELINE ASSEMBLYBUSH HOG HMG8, HMG9, HMG10

HAY MOWER

94-1-11

DRIVE BELTS, SHIELDS, FRAME SUPPORT & RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-12

DRIVE BELTS, SHIELDS, FRAME SUPPORT & RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

Ref. Part No. Description QuantityHMG7 HMG8 HMG9 HMG10

1 701112C Selflocking Nut M12 72 701513C Washer, Flat M12 53 00787106 Rear Housing 14 00787108 Threaded Pin M10 55 00756026 Screw M12x30 26 00788144 Cup Miller Washer M12 47 00788145 Washer, Flat 12-48x3 28 00787107 Belt 19 00787110 Big Pulley 110 00787109 Small Pulley 111 00787335 Washer, Shim 212 00787111 Front Housing 113 00787090 Locking Pin 114 00788146 Washer, Flat 36.5-65x5 115 00787115 Plastic Bushing 416 701520C Washer, Flat M27 217 00787116 Main Pivot 118 703416 Spring Pin 319 00787118 Threaded Turnbuckle 120 701515C Washer, Flat M16 221 00787117 Hex Pin 122 00787133 Washer, Flat 18-35x4 223 00787128 Spring For Backstand 124 701114C Selflocking Nut M16 125 00787327 Washer, Flat 20-60x3 126 701116C Selflocking Nut M20 127 710850 Key 128 00787336 External Retaining 129 00787132 Transmission Shaft 130 02969728 Screw M6x20 331 70159C Washer, Flat M6 332 00787131 Security Guard 133 00787114 Bearing, Ball - Sealed 234 70118C Selflocking Nut M6 335 00787123 Safety Hook Spring 136 70497 Cotter Pin 5x50 137 00787122 Safety Hook 138 00787412 Safety Click Bar 139 00756373 Screw M16x50 340 00788178 Anti-Loose Plate 141 00787120 Joint Vane 142 00787121 Security Pin 143 00787112 Frame Support 144 00787113 Rubber Pawl 145 00788179 Truss Head Screw 246 70209C Cover Plate For Belt Inspection Slot 1

94-1-13

CURTAIN, FRAME, SWATH BOARD & RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-14

CURTAIN, FRAME, SWATH BOARD & RELATED PARTSBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

Ref. Part No. Description QuantityHMG7 HMG8 HMG9 HMG10

1 50069784 Safety Curtain HMG7 150069785 Safety Curtain HMG8 150069786 Safety Curtain HMG9 150069787 Safety Curtain HMG10 1

2 00765898 Screw M10x60 5 5 5 73 701512C Washer, Flat M10 10 10 10 124 701511C Washer, Flat M8 4 4 4 65 700314C Selflocking Nut M8 2 2 2 36 701111C Selflocking Nut M10 10 10 10 127 00787207 Front Frame HMG7 1

00787208 Front Frame HMG8 100787209 Front Frame HMG9 100787210 Front Frame HMG10 1

8 00787211 Safety Curtain Cap 49 610613c8 Screw M10x100 210 00787216 Flat Rod 111 610712C8 Screw M12x110 412 701513C Washer, Flat M12 1613 00787212 Lateral Frame Support Attachment 114 00787197 Upper Frame HMG7 1

00787198 Upper Frame HMG8 100787199 Upper Frame HMG9 100787200 Upper Frame HMG10 1

15 701112C Selflocking Nut M12 1016 00787213 Drum 117 71575C10 Screw M12x40 418 00787215 Support - Main Frame (Outer) 119 00787214 External Swather 120 00787206 Swath Board 121 00787205 Swath Reinforcement Bar 122 02959661 Screw M12x35 423 ------------- Flatwasher M12 1024 00787201 Rear Frame HMG7 1

00787202 Rear Frame HMG8 100787203 Rear Frame HMG9 100787204 Rear Frame HMG10 1

25 610612C8 Screw M8x95 2 2 2 326 00788151 H.S.B.H.S. Screw 227 00787345 H.S.B.H.S. Screw 328 00765692 Screw M12x45 2

94-1-15

DECAL PLACEMENTBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-16

REF. PARTNO. NO. DESCRIPTION QTY.

1 00787358 Decal, Warning - Notice To Owner 12 00787359 Decal, Warning - Notice To Owner 13 00787360 Decal, Warning - Pressure Hazard 14 00787361 Decal, Warning-540 PTO Speed 15 00787362 Decal, Danger/Warning - Disc Stop 26 00787363 Decal, Danger/Warning - Rotating Knives 17 00787364 Decal, Warning-Safe Distance 28 00787365 Decal, Warning-Machine Ride 19 00787366 Decal, Warning-Entanglement Hazard 110 00787367 Decal, Warning-Crushing Hazard 111 00787368 Decal, Warning-Belt Stop 112 00787369 Decal, Danger-Crushing & Shearing Hazard 1*13 00787370 Decal, Warning-Crushing Hazard 114 00787371 Decal, Warning - Hook Point 115 00787372 Decal, Equipment To Wear 116 00787373 Decal, Lubrication Points 117 00787374 Decal, Oil Tank 118 50069773 Model Decal, HMG7 1

50069774 Model Decal, HMG8 150069775 Model Decal, HMG9 150069776 Model Decal, HMG10 1

19 50065309 Decal, Bush Hog-14.85" 120 00776031 Canister, Parts Manual 121 50069777 Manual, Operators HMG 1

*Permanently Attached To Cover Sheet.If Not Readable, Order Complete Cover Sheet.

DECAL PLACENMENTBUSH HOG HMG7, HMG8, HMG9, HMG10

HAY MOWER

94-1-17

DECALS - PICTORIALS (PART 1)

REF. PARTNO. NO. DESCRIPTION QTY.

1 00787358 Decal, Warning - Notice To Owner 12 00787359 Decal, Warning - Notice To Owner 13 00787360 Decal, Warning - Pressure Hazard 14 00787361 Decal,Warning-540 PTO Speed 15 00787362 Decal, Danger/Warning - Disc Stop 26 00787363 Decal, Danger/Warning - Rotating Knives 17 00787364 Decal, Warning-Safe Distance 28 00787365 Decal, Warning-Machine Ride 19 00787366 Decal, Warning-Entanglement Hazard 110 00787367 Decal, Warning-Crushing Hazard 111 00787368 Decal, Warning-Belt Stop 1

94-1-18

DECALS - PICTORIALS (PART 2)

REF. PARTNO. NO. DESCRIPTION QTY.

12 00787369 Decal, Danger-Crushing & Shearing Hazard 1*13 00787370 Decal, Warning-Crushing Hazard 114 00787371 Decal, Warning - Hook Point 115 00787372 Decal, Equipment To Wear 116 00787373 Decal, Lubrication Points 117 00787374 Decal, Oil Tank 118 50069773 Model Decal, HMG7 119 50069774 Model Decal, HMG8 120 50069775 Model Decal, HMG9 121 50069776 Model Decal, HMG10 122 50065309 Decal, Bush Hog-14.85" 1

*Permanently Attached To Cover Sheet. If NotReadable, Order Complete Cover Sheet.

94-1-19

CONVERSION KIT PARTS LISTINGBUSH HOG HMG8, HMG10

HAY MOWER

REF. PARTNO. NO. DESCRIPTION QTY.

- 00787231 Kit, Anti-Wear Skid Plate 1 Per Disc - 00787347 Plate, Anti-Wear Slide Skid 1 Per Kit - 00787345 Screw, Sckt But Hd 10 x 25 PL10 2 Per Kit - 701111C Nut Met TLE (Thin) 10-P1.5 PL 2 Per Kit - 00787232 Kit, Cutting Height Conversion 1 Per Machine - 00787348 Wdmt, Cutting Height Plate 2 Per Kit - 00787344 Nut Met Flange 10-P1.50 PL 4 Per Kit - 701111C Nut Met TLE (Thin) 10-P1.5 PL 4 Per Kit - 00787228 Kit, 3 Blade Conversion -6 Disc 1 Per Machine (Only HMG8)- 00787349 Wdmt, (3) Blade Disc 4 Per Kit - 00787350 Wdmt, (3) Blade Outer Disc Hat 2 Per Kit - 00787338 Nut Met Flange 12-P1.75 PL 6 Per Kit - 00787166 Blade, RH -CW 3 Per Kit - 00787168 Bolt, Blade 6 Per Kit - 00787167 Blade, LH -CCW 3 Per Kit - 00787230 Kit, 3 Blade Conversion -8 Disc 1 Per Machine (Only HMG10)- 00787349 Wdmt, (3) Blade Disc 6 Per Kit - 00787350 Wdmt, (3) Blade Outer Disc Hat 2 Per Kit - 00787338 Nut Met Flange 12-P1.75 PL 8 Per Kit - 00787166 Blade, RH -CW 4 Per Kit - 00787168 Bolt, Blade 8 Per Kit - 00787167 Blade, LH -CCW 4 Per Kit

Anti-Wear Skid Plate

Cutting Height Conversion

3 Blade Conversion

3 Blade OuterDisc Hat

3 Blade Disc

94-1-20

2501 Griffin Ave.• Selma, AL 36703(334) 872-6261 • (334) 874-2700Parts Ordering 1-800-304-2836

Fax 1-800-572-1784www.bushhog.com