International Light Technologies LED Refrigerated Case Lighting System

ILTCaseLightLED Refrigerated Case Lighting System

ILTINNOVATIONS

I n te rnat i ona lL ight Te chno log i e s , Peabody, MA (USA ) • 4 0 Ye a r s o f L i g h t i n g E x p e r i e n c e – W e K n o w L i g h t !

10 Technology Drive, Peabody, MA 01960978-818-6180 978-818-6181 fax

intl-lighttech.com

ISO 9001:2000

I n t e r n a t i o n a l L i g h t T E C H N O L O G I E SI n t e r n a t i o n a l L i g h t T E C H N O L O G I E S

2.18"

1.17

"1.17

"

1.65"

Part Number Description Color Temp. (K) Lumens Energy (Watts) Life (Hours) CRI (Typical)

ILT60-BAO-W50CE CaseLight, 60”, Brite Anodize, Center unit 5000 1100 20 50000 87ILT60-BAO-W50LE CaseLight, 60”, Brite Anodize, Left unit 5000 550 10 50000 87ILT60-BAO-W50RE CaseLight, 60”, Brite Anodize, Right unit 5000 550 10 50000 87




ILT-CEN-60-24 Power Supply, 100-277VAC in, 24VDC out, powers up to 3 – 60”Center units - - -

caselight brochure for IR:Layout 1 6/23/11 10:57 AM Page 1

Easily Replace Existing Cooler/Freezer Display Case Fluorescent LightsEasy Mounting Using TEK Screws or VHB Foam Tape When Space is Limited No Need to Empty Shelves!Lower Energy Bills and No Burned Out Bulbs!Long Fixture Life – YEARS vs. Weeks/MonthsLow Maintenance – 5 Year Warranty on CaseLight Modules & Power SuppliesDLC Listed – Eligible for ALL Rebates CaseLight Modules Made in the USA

Improving on the success of ILT's previous CaseLight modules for refrigerated/freezer display cases, ILT's new, more efficient CaseLight module has even lower power consumption and higher overall optical performance for your reach-in coolers and freezers. For Retrofit or New cases, ILT CaseLight can be installed easily and cost-effectively.

LED-based CaseLight modules provide all of the advantages of LED-based lighting including much longer life (greater than 50,000 hours), much lower energy consumption and much better lighting characteristics – brighter light focused on the merchandise. Plus all of ILT's CaseLight modules are DLC listed qualifying for maximum utility rebates.

Make Your Prepared Foods POP With CaseLight™ LED Modules!

40-Plus Years of ILT Lighting Experience Goes Into Every CaseLight!

CaseLight is DLC Listed!


• EasilyReplaceExistingCooler/FreezerDisplayCase FluorescentLights • EasyMountingUsingTEKScrewsorVHBFoamTape WhenSpaceisLimited •NoNeedtoEmptyShelves!

• LowerEnergyBillsandNoBurnedOutBulbs!

• LongFixtureLife–YEARSvs.Weeks/Months • LowMaintenance–5YearWarranty onCaseLightModules&PowerSupplies

• DLCListed–EligibleforALLRebates

• CaseLightModulesMadeintheUSA




ILTINNOVATIONS



intl-lighttech.com

ISO 9001:2000


2.18"

1.17

"1.17

"

1.65"













CaseLight is DLC Listed!ILTCaseLightLED Refrigerated Case Lighting System

ILTINNOVATIONS



intl-lighttech.com

ISO 9001:2000


2.18"

1.17

"1.17

"

1.65"















ILTINNOVATIONS



intl-lighttech.com

ISO 9001:2000


2.18"

1.17

"1.17

"

1.65"












40-Plus Years of ILT Lighting ExperienceGoes Into Every CaseLight!


45-PlusYearsofILTLightingExperienceGoesIntoEveryCaseLight!


ILTINNOVATIONS



intl-lighttech.com

ISO 9001:2000


2.18"

1.17

"1.17

"

1.65"














45


intl-lighttech.com

ISO 9001:2008













intl-lighttech.com

ISO 9001:2008













intl-lighttech.com

ISO 9001:2008













ILTINNOVATIONS

I n te rnat i ona lL ight Te chno log i e s , Peabody, MA (USA) • 4 0 Ye a r s o f L i g h t i n g E x p e r i e n c e – W e K n o w L i g h t !


intl-lighttech.com

ISO 9001:2000


2.18"

1.17

"1.17

"

1.65"















intl-lighttech.com

ISO 9001:2008ISO/IEC 17025:2005


1.17

"

1.65"

C US

Model # Description Color Temp. Lumens Watts CRI Recommended (K) (W) Applications

ILT48-BAO-W35LH Horizontal CaseLight, 48”, 3500 1135 26.6 90 Fresh meatsBrite Anodize, Left configuration.

ILT48-BAO-W35RH Horizontal CaseLight, 48”, 3500 1135 26.6 90 Fresh meatsBrite Anodize, Right configuration.

ILT48-BAO-W40LH Horizontal CaseLight, 48”, 4000 1135 26.6 90 Produce, dairyBrite Anodize, Left configuration.

ILT48-BAO-W40RH Horizontal CaseLight, 48”, 4000 1135 26.6 90 Produce, dairyBrite Anodize, Right configuration.

ILT48-BAO-W50LH Horizontal CaseLight, 48”, 5000 1200 26.6 87 Frozen foodBrite Anodize, Left configuration.

ILT48-BAO-W50RH Horizontal CaseLight, 48”, 5000 1200 26.6 87 Frozen foodBrite Anodize, Right configuration.







ILT-CEN-60-24 60 Watt, UL Class 2 Power Supply 100-277VAC input, 24VDC output Powers up to 2 – 70” unitsILT-LPF-40-24 40 Watt, UL Class 2 Power Supply 100-277VAC input, 24VDC output Powers up to 2 – 48” unitsILT-D24V100UNVA 100W, UL Class 2 Power Supply 120-277VAC input, 24VDC output Powers up to 3 – 70” units or 4 – 48” units

final horizontal CaseLight brochure_Layout 1 9/18/12 4:06 PM Page 2


intl-lighttech.com

ISO 9001:2008ISO/IEC 17025:2005


1.17

"

1.65"

C US
















PowerSupplies

ILT-LPF-40-2440 Watt, UL Class 2, 100-277VAC input, 24VDC output

ILT-CEN-60-2460 Watt, UL Class 2, 100-277VAC input, 24VDC output

ILT-D24V100UNVA100W, UL Class 2, 120-277VAC input, 24VDC output

5000 1200 15 50000 855000 600 7.5 50000 855000 600 7.5 50000 85

4000 1160 15 50000 854000 580 7.5 50000 854000 580 7.5 50000 85

3500 1160 15 50000 853500 580 7.5 50000 853500 580 7.5 50000 85

5000 1600 20 50000 855000 800 10 50000 855000 800 10 50000 85

4000 1547 20 50000 854000 773 10 50000 854000 773 10 50000 85

3500 1547 20 50000 853500 773 10 50000 853500 773 10 50000 85

5000 2000 25 50000 855000 1000 12.5 50000 855000 1000 12.5 50000 85

4000 1940 25 50000 854000 970 12.5 50000 854000 970 12.5 50000 85

3500 1940 25 50000 853500 970 12.5 50000 853500 970 12.5 50000 85

* ILT48-BA0-W50CE* ILT48-BA0-W50LE* ILT48-BA0-W50RE



* Not DLC Listed

ILTINNOVATIONS

I n t e r n a t i o n a lL ight Te c h n o l o g i e s , P e a b o d y, M A ( U S A ) • 4 0 Y e a r s o f L i g h t i n g E x p e r i e n c e – W e K n o w L i g h t !


ILTCaseLightLED-Based HORIZONTAL Food Display Case Lighting

Make Your Prepared Foods POPWith CaseLight™ LED Modules!

� Easily Replace Existing Food Display Case Fluorescent Lights

� Adjustable Mounting Brackets Put the Light on the Product

� 1 CaseLight Module Replaces 2 Fluorescent Bulbs– Lower Energy Bills and No Burned Out Bulbs!

� Long Fixture Life – YEARS vs. Weeks/Months

� Low Maintenance – 5 Year Warranty on CaseLight Modules & Power Supplies

� DLC Listed – Eligible for ALL Rebates

� CaseLight Modules Made in the USA

Following on the success of ILT's Vertical CaseLight modules for

refrigerated/freezer display cases, ILT's new Horizontal CaseLight

module is designed to replace existing fluorescent light fixtures in

horizontal food display cases (reach-in/multi-deck dairy, produce

& prepared foods) easily and cost-effectively.

LED-based Horizontal CaseLight modules provide all of the advantages

of LED-based lighting including much longer life (greater than 50,000

hours), much lower energy consumption and much better lighting

characteristics – brighter light focused on the merchandise. Plus all

of ILT's CaseLight modules are DLC listed qualifying for maximum

utility rebates.


ILTINNOVATIONS

I n t e r n a t i o n a lL ight Te c h n o l o g i e s , P e a b o d y, M A ( U S A ) • 4 0 Y e a r s o f L i g h t i n g E x p e r i e n c e – W e K n o w L i g h t !

CaseLight™ Features Include:� Fast ROI - 18-20 months - Even Faster with Rebates

� One Horizontal CaseLight Module Typically Replaces 2 Fluorescent Fixtures

� Adjustable Mounting Brackets for Optimal Product Illumination

� Multiple Color Temps Available – Match to Specific Food Group (ex. Red Meat)

� Long Life / Low Maintenance - 5 Year Warranty on CaseLight Modules & Power Supplies

� DLC Listed - Eligible for ALL Utility Rebates

� Eliminates Hazardous Waste Concerns - No Mercury

� CaseLight Modules Manufactured in the USA40-Plus Years of ILT Lighting Experience

Goes Into Every CaseLight!

Following on the success of ILT's Vertical CaseLight modules for

refrigerated/freezer display cases, ILT's new Horizontal CaseLight

module is designed to replace existing fluorescent light fixtures in

horizontal food display cases (reach-in/multi-deck dairy, produce &

prepared foods) easily and cost-effectively.

LED-based Horizontal CaseLight modules provide all of the advantages

of LED-based lighting including much longer life (greater than 50,000

hours), much lower energy consumption and much better lighting

characteristics – brighter light focused on the merchandise. Plus all

of ILT's CaseLight modules are DLC listed qualifying for maximum

utility rebates.

ILTCaseLightLED-Based HORIZONTAL Food Display Case Lighting

final horizontal CaseLight brochure_Layout 1 8/23/12 9:41 AM Page 1


intl-lighttech.com

ISO 9001:2008ISO/IEC 17025:2005


1.17

"

1.65"

C US












ILT70-BAO-W50LH Horizontal CaseLight, 70”, 5000 35.9 87 Frozen foodBrite Anodize, Left configuration.

ILT70-BAO-W50RH Horizontal CaseLight, 70”, 5000 35.9 87 Frozen foodBrite Anodize, Right configuration.


final horizontal CaseLight brochure_Layout 1 8/23/12 9:41 AM Page 2

1714 22.2 85

1714 22.2 85

1714 22.2 85

1714 22.2 85

2000 22.2 85

2000 22.2 85

2541 31.3 85

2541 31.3 85

2541 31.3 85

2541 31.3 85

3000 31.3 85

3000 31.3 85

Warranty Statement

September 3, 2012International Light TechnologiesProduct – CaseLight LED Light Fixture

CaseLight LED-based refrigeration/freezer lighting system (Vertical and Horizontal) is warranted for a period of 5 years against manufacturers defects, including any failures of the LEDs. Any external power supply provided by International Light Technologies, sold as a system to power CaseLight LED units is also warranted for a period of 5 years. Any failed LED CaseLight unit or power supply will be repaired or replaced within the 5 year warranty period.

Model numbers include -

Caselight LED Unit:ILTXX-YYY-WZZ-A (or AE or AH) whereXX – Length up to 72” long (48 – 48” long)YYY – represents the unit colorWZZ – where ZZ is the LED color temperatureA – represents the Center/Left/Right configurationsor AE – where E represents External Power Supply configuration for Vertical unitsor AH – where H represents Horizontal configuration with external power supply(example ILT60-BAO-W35CE; 60”, Brite Anodize, 3500K, Center unit)

Power Supply Options:ILT-CEN-60-24 – 60W, 24VDC Meanwell power supply(Astrodyne is private label)ILT-LPF-40-24 – 40W, 24VDC Meanwell power supply

All units are warranted for 5 years as of the ship-date from International Light Technologies.

Installation Instructions

Note – Wiring and mounting instructions are applicable for both center and end units

Model Numbers – Example ILT60-BAO-W50CEILTAA-

(AA=Length-inches)BAO-

(Brite Anodize finish)

WBB(BB=color temp)

CE(C=Configuration; E=External Power

Supply)ILT48 (48”) “ 35 (3500K) CE (Center, External Power Supply)ILT60 (60”) “ 40 (4000K) LE (Left, External Power Supply)ILT70 (70”) “ 50 (5000K) RE (Right, External Power Supply)

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

B. Before installing, servicing or cleaning unit, switch power off at the service panel and follow appropriate lock out / tag out safety procedures.

FOR YOUR SAFETY:Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing installations described, gloves, safety glasses or goggles should be worn.

PREPARE ELECTRICAL WIRING:A. Electrical Requirements – This fixture must be powered by a Meanwell, 60W, 24VDC power

supply, model CEN-60-24, ILT part number ILT-CEN-60-24, connected to a properly grounded branch circuit, protected by a circuit breaker.

B. Grounding Instructions – This power supply must be connected to a grounded metal, permanent wiring system.

C. Strain Relief Requirements – This fixture is equipped with a cord but no attachment plug. Therefore, the installer must include a strain relief sized properly for the cable and opening in the junction box it is attaching to. An example is the Heyco Products strain relief, part number 1150, or equivalent if routing wire into a junction box or through an access hole.

CI-101 Rev. A Page 1 4/25/2012

International Light Technolgies 978-818-6180 Brite Energy Solutions 308-367-4542

TOOLS NEEDED:- Wire connectors- Wire cutters- Gloves- Tape measure- Wire stripper- Safety glasses- Center punch- Power drill- Screwdriver- #6 x 1 1/2” self-tapping screws

Prepare for Mounting Light Fixture to Mullion – using #6 x 1 1/2” self-tapping screws

CAUTION – Turn off power to the mullion lighting system before removing any covers.- Measure the total length of the mullion to determine which model/length unit to install. Center

the fixture vertically on the mullion. Mark the top and bottom of the fixture.- Measure the total width of the mullion and mark a vertical line, ½ the total width near the top,

6” from the top, 6” from the bottom.- Mark a horizontal line 6” down from the top of the fixture. Mark a horizontal line 6” from the

bottom of the fixture.

CAUTION – Prior to installing screws, make sure that there are no existing components inside the mullion in the areas to be drilled. Do not drill through “DO NOT DRILL” label.

- Use power drill and screw bit and install 4, #6 x 1 1/2” self-tapping screws through the center indent of the fixture. Install 2-3 screws, one 6” from top, one 6” from bottom and one in the center if necessary.

NOTE – Starting the screws into the fixture with the fixture outside the cooler may make it easier for installation. Screws can then be fully inserted into mullion while holding fixture in place.

Alternate Mounting MethodHigh quality VHB-type foam tape may also be used to mount the fixtures.

− Thoroughly clean the back of the fixture and the mullion surface.− Using 1/2”-3/4” wide VHB tape, apply tap to back surface of fixture to within 3” of top and

bottom of fixture.

CI-101 Rev. A Page 2 4/25/2012

10 Technology Dr., Peabody, MA 01960 978-818-6180 978-818-6181 fax

− Dry fit fixture to mullion. Once fit is confirmed, peel release paper, align fixture and press against mullion for entire length of fixture.

Connect Wiring from FixtureCAUTION – Ensure that all connection points are sealed for damp location using the appropriate method per the NEC or local electrical code.

- Cut the fixture cable to the appropriate length to terminate to DC power at the Power Supply.- Where necessary, insert the proper strain relief on the cable and secure to hole in mullion or

junction box.- Strip the cable jacket and then strip the individual two wires. Attach the Black wire to the

Black wire of the power supply using twist-on wire connector. Attach the Red wire to the Red wire of the power supply using twist-on wire connector.

Connect Wiring to Power SupplyCAUTION – Wiring to high voltage side of power supply to be accomplished by certified electrician in accordance with NEC or local electrical code.

Trouble-shooting and Maintenance InstructionsCAUTION – Turn off power to the mullion lighting system before removing any covers.

The following items can be replaced in the field:- 60W Power Supplies- LED flex strips (access to end of unit required)

TROUBLE-SHOOTING- If an entire strip of LEDs are not lighted (one of the two strips for a center unit or the one strip

of an end unit), either there is a wiring problem to that strip or the LED driver is defective.- Check wiring connections to the unit at the driver. If the connections look OK, proceed to

“Replacement of LED Driver”.- If both LED strips are not lighted on a center unit or the single strip isn’t lighted on an end-unit,

it is possible that power to the unit has been interrupted. Confirm that the cable to the unit is wired properly and securely to the DC power source.

Replacement of LED Flex Strip- Remove the 2, #4 screws securing the end-cap where the cable exits the unit. - Slide out the lens on the side of the defective LED flex strip.- Cut the two wires from the defective LED flex strip about 6” from the end of the strip.

CI-101 Rev. A Page 3 4/25/2012


- Remove the defective LED flex strip by peeling away from the housing.- Install the new LED flex strip by peeling the release tape and sticking to the housing. Start at

wired end positioning start of strip about 1” from end of housing. Continue down the full strip, pressing in between components to insure a good bond.

- Connect Red and Black wires to the wires previously cut. Attach using twist on wire nuts.- Push the wire nuts inside extrusion.- Slide in lens which was previously removed. Re-attach end-caps with 2 #4-40 screws

previously removed.

Fixture Cleaning Instructions- The lens and aluminum housing should be cleaned periodically with a mild liquid dish

detergent.- Do not use chemical cleaners on the lens.- Keep the outside clean. Wipe with a clean cloth lightly dampened with mild liquid dish

detergent. Dry with a clean, soft cloth. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and damage the finish.

Door Configurations The ILT-CEN-60-24, 60W, 24VDC power supply can power up to 3 Center units. Here are three typical door configurations and the number of power supplies required for each.

# of Doors # of Center Units

# of End Units # of Power Supplies

Notes

3 2 2 14 3 2 2 2 Centers-1 End; 1 Center-1 End5 4 2 2 2 Centers-1 End per P.S.

6 5 2 32 Centers-1 End per P.S. It is possible to wire 2 Centers and 2 Ends on 1 P.S.

CI-101 Rev. A Page 4 4/25/2012


End EndCenter Center

3 Door Case = Two End Units & Two Center Units


4 Door Case = Two End Units & Three Center Units

Center


5 Door Case = Two End Units & Four Center Units

Center Center

60W PSAC input24Volt DC


60W PS


60W PS

ILT INNOVATIONS

Power SupplyWiring Configuration

10 Technology Drive Peabody, MA 019601-978-818-6180 www.intl-lighttech.com

Date post:	17-Mar-2016
Category:	Documents
Upload:	tom-knoblock
View:	242 times
Download:	13 times

International Light Technologies LED Refrigerated Case Lighting System

Documents