Method of Selection - Bay Port Valve · 2013-04-28 · Bar stock meets N.A.C.E. MR-01-75...

ThermowellsSpecializing in

• Method of Selection

• Service Ratings

• Corrosion Data

Engineering Company, Inc.

Specializing in Thermowells

304 Seaview Avenue • P.O. Box 4036 • Bridgeport, CT 06607-0036Phone: (203) 366-5253 (800) 827-8240 • Fax: (203) 334-0793

E-mail: [email protected] • Website: http://www.thermowells.com

Engineering Company, Inc.

Made in USA

Catalog No. 7L-E 7/99 © 1999, Alloy Engineering Company, Inc.

ServiceDedicated to the principle of service and high quality, Alloy Engineering Companyrepresents an unusual combination of Engineering and Manufacturing know-how, not stopping at thermowell manufacture, but carrying on into completefamiliarity with application and detailed knowledge of the instruments which usethermowells as a means of protection. Alloy has been manufacturing thermowellssince 1958 and is still the largest thermowell specialist. We reply to all inquirespromptly via return telephone, FAX, email or mail.

SpecializationSince 1958, our company has specialized in the manufacture of thermowells forall kinds and makes of thermometers and temperature sensing elements. Thistype of specialization means intensive concentration on the problems of serviceand manufacture which brings about best possible delivery, lowest costs andhighest quality.

QualityWe take special pride in producing the finest thermowells ever made. Our Q.C.system and manual have been approved for government and nuclear service bythe major contractors. Wells made of corrosion resisting materials are highlypolished to assure maximum corrosion resistance. Our quality system meets therequirements of ISO 9002.

Material Selection/TraceabilityALLOY maintains an inventory of special alloys such as Titanium, Hastelloy B&C,Incoloy, 446SS, 410SS, Nickel, Monel, Inconel 600, Teflon, Aluminum, F-22,A-105, Bronze, etc., for prompt delivery.Throughout our entire manufacturing process the material is traceable to the MillTest Reports which are available upon request.Materials comply with ASTM and industry standards. Nuclear quality material isavailable upon request.Bar stock meets N.A.C.E. MR-01-75 specification. Flanged wells can be heattreated to comply with the N.A.C.E. specification.

A W

ord

Abo

ut A

lloy

Engi

neer

ing

Com

pany

Corrosive Service Guide To Materials

In recommending the above materials, consideration has been given to providing good service life without undue cost. Where two or more materials are satisfactory,the least expensive is listed. Consult the factory for information on materials or services not given.

Temp. Conc. Recom.Corrodent °F % Material

Acetic Acid 212 All MonelAcetic Anhydride 300 NickelAcetone 212 All 304 SSAcetylene 400 304 SSAlcohols 212 All 304 SSAlum. (Potassium 300 All Hast. C or Sodium)Aluminum Chloride 212 All Hast. BAluminum Sulfate 212 All 316 SSAmmonia, Dry 212 All 304, 316 SSAmmonium Hydroxide 212 All 304, 316 SS (Ammonia, Aqua)Ammonium Chloride 300 50% MonelAmmonium Nitrate 300 All 304 SSAmmonium Sulfate 212 All 316 SSAmyl Acetate 300 All 304 SSAniline 75 MonelAsphalt 250 304 SSAtmosphere 304 SS (Industrial and Marine)Barium Compounds SEE CALCIUMBeer 70 304 SSBenzene (Benzol) 212 SteelBenzoic Acid 212 All 316 SSBleaching Powder 70 15% MonelBorax 212 All BrassBordeaux Mixture 200 304 SSBoric Acid 400 All 316 SSBromine 125 Dry MonelButane 400 All SteelButyl Alcohol SEE ALCOHOLSButyric Acid 212 Hast. CCalcium Bisulphite 75 All Hast. CCalcium Chloride 212 All Hast. CCalcium Hydroxide 300 20% Hast. CCalcium Hypochlorite SEE BLEACHING POWDER

Carbolic Acid SEE PHENOLCarbon Dioxide, Dry 800 All BrassCarbonated Water 212 All 304 SSCarbonated Beverages 212 304 SSCarbon Disulfide 200 304 SSCarbon Tetrachloride 125 All MonelChlorine, Dry 100 MonelChlorine, Moist 100 All MonelChloracetic Acid 212 All MonelChloroform, Dry 212 MonelChromic Acid 300 All Hast. CCider 300 All 304 SSCitric Acid 212 All Hast. CCopper (10) Chloride 212 All Hast. CCopper (10) Nitrate 300 All 316 SSCopper (10) Sulfate 300 All 316 SS


Copper Plating Solution 180 304 SS (Cyanide)Copper Plating Solution 75 304 SS (Acid)Corn Oil 200 304 SSCreosote 200 All 304 SSCrude Oil 300 MonelEthyl Acetate SEE LACQUER THINNEREthyl Chloride, Dry 500 SteelEthanol SEE ALCOHOLSEthylene Glycol 212 All 304 SS (Uninhibited)Ethylene Oxide 75 SteelFatty Acids 500 All 316 SSFerric Chloride 75 All Hast. CFerric Sulfate 300 All 304 SSFormaldehyde 212 40% 316 SSFormic Acid 300 All 316 SSFreon 300 SteelFluorine, Anhydrous 100 304 SSFurfural 450 316 SSGasoline 300 SteelGlucose 300 304 SSGlue ph 6-8 300 All 304 SSGlycerine 212 All BrassHydrobromic Acid 212 All Hast. CHydrochloric Acid 225 All Hast. B (37-38%)Hydrogen Chloride, Dry 500 304 SSHydrocyanic Acid 212 All 304 SSHydrofluoric Acid 212 60% MonelHydrogen Fluoride, Dry 175 SteelHydrofluogilicic Acid 212 40% MonelHydrogen Peroxide 125 10-100% 304 SSKerosene 300 All SteelLacquers & Thinners 300 All 304 SSLactic Acid 300 All 316 SSLime 212 All 316 SSLinseed Oil 75 SteelMagnesium Chloride 212 50% NickelMagnesium Hydroxide 75 All 304 SS (or Oxide)Magnesium Sulfate 212 40% 304 SSMercuric Chloride 75 10% Hast. CMercury 700 100% SteelMethylene Chloride 212 All 304 SSMethyl Chloride, Dry 75 SteelMilk, fresh or sour 180 304 SSMolasses SEE GLUCOSENatural Gas 70 304 SSNitric Acid 75 All 304 SSNitric Acid 110 All 316 SS


Oxygen 75 All SteelOleic Acid SEE FATTY ACIDSOxalic Acid 212 All MonelPhotographic Bleaching 100 All 304 SSPalmitic Acid SEE FATTY ACIDSPhosphoric Acid 212 All 316 SSPhenol 212 All 316 SSPotassium Compounds SEE SODIUM COMPOUNDS

Propane 300 SteelRosin 700 100% 316 SSSea Water 75 MonelSoap & Detergents 212 All 304 SSSodium Bicarbonate 212 20% 316 SSSodium Bisulphate 212 20% 304SSSodium Bisulphite 212 20% 304 SSSodium Carbinate 212 40% 316 SSSodium Chloride 300 30% MonelSodium Chromate 212 All 316 SSSalt or Brine SEE SODIUM CHLORIDESodium Cyanide 212 All 304 SSSodium Hydroxide 212 30% 316 SSSodium Hypochlorite 75 10% Hast. CSodium Nitrate 212 40% 304 SSSodium Nitrite 75 20% 316 SSSodium Phosphate 212 10% SteelSodium Silicate 212 10% SteelSodium Sulfate 212 30% 316 SSSodium Sulfide 212 10% 316 SSSodium Sulfite 212 30% 304 SSSodium Thiosulfate 212 All 304 SSSteam 304 SSStearic Acid SEE FATTY ACIDSSugar Solutions SEE GLUCOSESulfur 500 304 SSSulfur Chloride 75 Dry 316 SSSulfur Dioxide 500 Dry 316 SSSulfur Trioxide 500 Dry 316 SSSulfuric Acid 212 10% 316 SSSulfuric Acid 212 10-90% Hast. BSulfuric Acid 212 90-100% Hast. BSulfuric Acid, Fuming 175 Carp. 20Sulfurous Acid 75 20% 316 SSTitanium Tetrachloride 75 All 316 SSTannic Acid 75 40% Hast. BToluene 75 SteelTrichloracetic Acid 75 All Hast. BTrichlorethylene 300 Dry MonelTurpentine 75 316 SSVarnish 150 SteelZinc Chloride 212 All Hast. BZinc Sulfate 212 All 316 SS

2 23

ContentsOptional Services page 7

Standard for 1/4” Element page 8

Heavy Duty for 1/4” Element page 9



Socket Weld Series page 12

Heavy Duty Socket-Weld page 13

Flanged Series page 14

Tapered Flanged Series page 15

General Purpose Test page 16

Limited Space page 16

Industrial Thermowells page 17

Van Stone Thermowells page 18

1-1/2” Dia. Weld-In Series page 19

Sanitary Type Thermowells page 20

Protection Tubes page 20

Tantalum Jackets page 21

Teflon Thermowells page 21

Manufacturing Tolerances page 22

Corrosive Service Guide page 23

Expense connected with thermowell selection does not end with the initial

purchase. Listed below are some of the reasons for the careful dimensioning of

the Thermowells in this catalog. Note the emphasis on standardizing of bore size,

element (or stem) length and other internal dimensions. You will discover other

benefits to using standard wells as time goes on.

Save On Initial InvestmentStandard wells are produced on a large quantity basis bringing about reduced

cost and improved delivery. Temperature sensing elements are lower in cost

since you are buying larger quantities of particular sizes.

Gain Overall FlexibilityA temperature sensing element in a threaded well also fits a flanged well

downstream, or a socket weld well on main steam. Pull out a Bi-metal thermometer

and insert a test thermometer or thermocouple in that same well. Since these

wells accept several types of sensing elements, instruments may be “swapped

around” to suit changing optional procedures or advancing technology.

Reduce Spare Instrument InventoryUse of standard wells throughout the plant can reduce the number of spare

instruments necessary to insure safe coverage. Less work is required by the

power plant designer in establishing a recommended spare list.

Minimize Down TimeEven if caught without a spare, chances are that an instrument, in a less critical

location can immediately be relocated to a measurement point where a failure

has resulted.

Lengths:± 1/16” on length 12” or less

± 1/8” on length 12” or over

Wells 30” overall length and longer will be

drilled thru end, plugged and heliarc welded,

if solid bored is specified. Built-up design

must be specified beyond 42 1/4” overall

length.

O.D. Tolerances:Fractional: ± .015

Decimal: ± .005 on .000 place

± .010 on .00 place

Bore I.D. Tolerances:+ .005

- .003

End Thickness:Gun Drill Bottom

1/4” to bottom ± 1/16”, 3/16” min. end

Concentricity of Bore to O.D.:± 10% of min. wall thickness

Surface Finish:16-32 Ra Standard

4-12 Ra available at an extra charge.

Must be specified on order.

Wetted surface finish of 80 Ra is available at

a savings on some wells.


Radius under Threads and Flanges:1/8” is standard, ± 1/16”

1/16” on Van Stones

Male Threads: (NPT)± 1 on thread gage

Female Threads:(1/2” NPSM) standard, 1/2” NPT available

upon request.

Go gage to 5/8” depth of thread

No go gage 2 turns max.

End of Wells:Break corners - No Burrs

Threaded WellsRound stock with wrench flats will be used if

hex stock is not available. Lagging extension

may be left as hex or as machined diameter.

Stamping:Material code identification and type of

material stamped on Hex or round facing

open end of well.

Flanged Wells:Made in accordance with ANSI B16.5.

Raised Face is serrated.

125 RMS Smooth Face must be specified on

order if needed.

Front “J”:Groove welds are 1/4” wide by 1/4” deep.

Welds are machined, leaving 1/8” radius.

Rear welds are 1/8” wide by 1/8” deep “V”.

Welds are machined, leaving 1/4 radius.

Full penetration welds are available upon

request. Must be specified.

Allo

y St

anda

rd M

anuf

actu

ring

Tole

ranc

es

Why

Sta

ndar

d T

herm

owel

ls?

22 3

Versatility and PriceALLOY has the capabilities of meeting all of your Thermowell requirementswhether they be a single piece or very large contract jobs at a competitive price.

SalesALLOY maintains ample finished and semi-finished stock levels to serve distributors,located throughout the USA and Canada. An expedited delivery service is availableupon request.

EngineeringThis catalog gives complete engineering information for the proper selection ofStandardized Thermowells. ALLOY’s engineers are willing and able to help withany design problems.

Manufacturing EquipmentAll wells are machined from solid bar stock on the most modern numerical controlmachines. Bores are produced on deep hole gun drilling machines which producesmooth true holes accurately centered in the sensitive part of the well.

Material - The Longevity FactorIn general, the thermowell material chosen for the installation is governed mainly

by the corrosion conditions the well will face. Recommended materials for various

services are given in the Corrosive Service Guide on page 23. The high polish

given to all stainless and monel wells provides maximum corrosion resistance

and strength. Occasionally, the material consideration is one of strength rather

than corrosion. For example, a stainless steel well may be required for high

pressure water service where otherwise a brass well would be satisfactory from

a corrosion standpoint. Consult the pressure-temperature ratings given for each

well type. The standard materials listed for each well series will cover most

requirements. Alloy carries a wide variety of special materials in inventory to

insure fast delivery of wells. Materials include special grades of Stainless Steel,

Chrome-molybdenum, Steel, Naval Brass, Hastelloy B&C, Nickel and Titanium.

Connection - The Installation FactorIn these pages you will find standardized wells of threaded, flanged (A.N.S.I. and

Van Stone) and socket weld types with standard bore sizes. Threaded wells are

all made in readily welded or brazed materials. This is important for installations

requiring seal welding or brazing. The pipe thread provides the mechanical

strength, the weld merely seals. Flanged wells (other than Van Stone type) consist

of a bar stock well which is solidly welded to a top quality flange. Standard

construction uses a primary “J” groove weld and a bevel groove secondary weld.

Both welds are machined to produce a clean fillet. This double welded construction

eliminates possibility of crevice corrosion and stress problems since no open

joints are exposed from either inside or outside the installation. Socket welding

types of wells are simple to install by merely welding into place. These wells fit

A.N.S.I. standard socket weld couplings or flanges. The resulting installation is

clean and tight.

Insertion Length - The Accuracy FactorThe distance from the end of the well to the underside of the thread, or other

connection means, (designated as “U”) is the insertion length. For best accuracy,

this length should be long enough to permit the entire temperature sensitive part

of the thermometer bulb to project into the temperature medium being measured.

Sele

ctio

n of

The

rmow

ells

Tantalum Jackets

1-800-827-8240 214

Teflon ThermowellsCoatedPFA Teflon coating applied .008” to .010” thick. Other coatingsavailable upon request.

Teflon’s ability to tolerate harsh chemical environments makethese wells ideal for use in highly corrosive applications.

SolidAvailable with 1/2”, 3/4” and 1” NPT process connection anda maximum overall length of 12-1/4”.

Solid Teflon thermowells are ideal for measuring temperaturein acid solutions or other caustic environments where thetemperature is under 400 deg. F at atmospheric pressure.

Not available in flanged configuration.

Tantalum jackets cover insertion length and raised facearea of flange. Used in applications where corrosion resistanceis critical.

Standard thickness of jacket:.015” on “U” dimension, raised face and end plug..030” thick jackets available upon request.

Tantalum jackets are available in 1/2”, 3/4” and 7/8” IDsizes to fit 1”, 1-1/2”, 2”, 3” and 4” flanges.

Also available in Titanium and Zirconium with 3/4” OD.

To ensure proper fit, please order with thermowell.

ApplicationsChlorineBromineHydrochloricNitricSulfuric acids

ApplicationsAcids and causticsCorrosivesElectroplatingFood & BeveragePharmaceuticals

A ELEMENT LENGTH 1/4

BORE

O.D.

U INSERTION LENGTH

WELD

FLANGE SIZE & FACINGAS REQUIRED

TANTALUM JACKETCovering “U” Dimension andRaised Face Portionof Flange

1-1/4

2-1/4

1/2 NSPM

A properly installed thermometer bulb will project into liquid an amount equal to

its sensitive length plus at least one inch. In air or gas, the bulb should be

immersed to its sensitive length plus at least three inches. Thermocouples and

thermistors have short sensitive lengths, therefore can use the smallest insertion

lengths. Bi-metal thermometers, resistance thermometers and liquid-in-glass

thermometers have bulbs with sensitive portions between one and two inches

long. Therefore, the minimum standard insertion length of 2 1/2” must be entirely

immersed in liquid for proper accuracy. Filled system thermometer bulbs may

have sensitive portions from one to several inches in length. Determine the

sensitive length of the bulb before choosing an insertion length. Above all - be

sure that dead length, ie. - that are required to pass thru walls, pipe fittings, etc.,

is taken into account when choosing the necessary well insertion length.

Bore Size - The Interchangeability FactorAlmost any installation uses several types of temperature measuring instruments.

The selection of a standard bore diameter can produce maximum flexibility within

the plant. The same well can accommodate either thermocouple, resistance

thermometer, bi-metal thermometer, or test thermometer. The bore size of wells

shown in this catalog cover the most commonly used temperature sensing

elements as follows:

.260 Diameter Bore: Bi-metal Thermometers (1/4” Stem)

Thermocouples - (#20 Gauge)

Liquid-in-glass Test Thermometers (unarmored)

Other elements having .252 maximum diameter



Liquid-in-glass Test Thermometers (armored)


Tapered or Straight Shank - The Velocity Rating FactorTapered shank wells provide greater stiffness for the same sensitivity. The higher

strength-to-weight ratio gives these wells a higher natural resonant frequency

than for an equivalent length straight shank well, permitting operation at higher

fluid velocities. Refer to “Velocity Ratings of Wells” on page 6.

Protection Tubes

260 Sanitary Series

Sanitary Type Thermowells

5

260 & 385 Sanitary SeriesTo Order, Please Specify:

1. 3/4”-260W or 385W2. “U” Dimension3. Material4. End Cap Size

20 1-800-827-8240

385 Sanitary Series

Protection tubes are available in various ID’s, OD’sand materials to suit your application.

Can be ordered with threaded or flanged processconnections.

ApplicationsOvensFurnacesOpen ContainersFluesDucts

ApplicationsFood & BeveragePharmaceuticals

Available with 1”, 1-1/2”, 2”, 3” and 4” #16 AMPend caps. Other sizes and styles available upon request.

Alloy has been granted authorization #747 forstamping the 3A symbol.

Shank Elem. Insert.Type Number Dia. Lgth. Lgth.

Q A U

260 -U 2-1/2 -- 4 2-1/2Sanitary -U 4-1/2 3/4 6 4-1/2

-U 7-1/2 “ 9 7-1/2-U10-1/2 “ 12 10-1/2-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2


Q A U

385 -U 2-1/2 49/64 4 2-1/2Sanitary -U 4-1/2 “ 6 4-1/2

-U 7-1/2 “ 9 7-1/2-U10-1/2 “ 12 10-1/2-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2

Sele

ctio

n of

The

rmow

ells

A ELEMENT LENGTH

U INSERTION LENGTH1-3/41/2 NPSM

1.050

.385 BORE

49/64

1/4

A ELEMENT LENGTH

Q Dia.=3/4


1.050

.260 BORE

1/2 DIA.

2-1/2WELD

1/4

P NPT1/4O.D.

I.D.

UT

AS SPECIFIED

WELD

P NPT1/4O.D.

I.D.

Well failures, in most cases, are not due to the effect of pressure and temperature.

The calculations necessary to provide adequate strength, under given conditions,

are familiar enough to permit proper choice of wall thickness and material.

Less familiar, and more dangerous, are the vibrational effects to which wells

are subjected. Fluid, flowing by the well, forms a turbulent wake (called the Von

Karman Trail) which has a definite frequency based on the diameter of the well

and velocity of the fluid. It is important that the well have sufficient stiffness so

that the wake frequency will never equal the natural frequency of the well itself.

If the natural frequency of the well were to coincide with the wake frequency, the

well would vibrate to destruction and break off in the piping.

On the following pages, a recommended maximum velocity rating can be found

for every standard well length and material cataloged. To reduce the complexity

of presenting this information, the ratings given are based on operating temperatures

of 1000ºF for wells made of Carbon Steel (C-1018), A.I.S.I. 304 & A.I.S.I. 316.

Values for brass wells are based on 350ºF operation. Limits for Monel wells are

based on 900ºF service. Slightly higher velocity is possible at lower temperatures.

Where single values appear in the velocity tables, these may be considered

safe for water, steam, air or gas. In the shorter insertion lengths, consideration

is given to the velocity pressure effect of water flowing at higher velocities. The

values in parenthesis, therefore, represent safe values for water flow while the

unbracketted value may be used for steam, air, gas and similar density fluids.

It should be pointed out that the values given are extremely conservative, and

intended primarily as a guide. Wells are also safe if the resonant frequency is

below the wake frequency or if the fluid velocity is constantly fluctuating through

the critical velocity point. If the installation is not hampered by the use of a

sufficiently stiff well, we recommend the values given not be exceeded.

If you have operating conditions requiring special well designs, our Engineering

Staff is available to assist you.

Elem. Insert. BoreType Number Lgth. Lgth. Dia.

A U B

1-1/2” -U 2-1/2 4 2-1/2Dia. -U 4-1/2 6 4-1/2385 -U 7-1/2 9 7-1/2

Weld-In -U10-1/2 12 10-1/2 .385-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 24 22-1/2

Application:260 weld-in series fits 1/4” diameter elements.385 weld-in series fits 3/8” diameter elements for weldingdirectly into piping.

Materials:Carbon Steel (C-1018 or A-105 as specified),304SS, 316SS, Chrome Moly (F-11 or F-22 as specified).Other materials are available.

Plug & Chain:Brass or Stainless Steel captive plug is available forkeeping well bore clean when not in use.

Lagging Extension:Specify by adding “T” lagging to 1-3/4” head dimension.

Maximum Fluid Velocityfeet per second

(See Section on Velocity Ratings on page 6.)

1-1/2” Dia. Carbon Steel 451 269.0 96.9 49.0 29.9 20.0 14.0 10.7(286) (159)

385 A.I.S.I. 304 & 316 531 285.0 102.0 52.0 31.6 21.2 15.0 11.4(385) (220)

Weld-In F-11 or F-22 542 290.0 104.0 53.2 32.0 21.5 15.4 11.6(392) (224)

Insertion Length - “U”

Well Type Material 2-1/2 4-1/2 7-1/2 10-1/2 13-1/2 16-1/2 19-1/2 22-1/2

1-1/2” Dia. Carbon Steel 493 220.0 79.4 40.5 24.5 16.4 11.7 8.8(306) (170)

260 A.I.S.I. 304 & 316 539 233.5 84.0 42.8 25.9 17.3 12.4 9.3(443) (231)

Weld-In F-11 or F-22 549 237.0 85.5 43.0 26.4 17.6 12.6 9.5(451) (235)

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°

Carbon Steel 5950 5750 5450 5250 4000 1750 ---A.I.S.I. 304 7800 7050 6400 6150 6000 5190 1875A.I.S.I. 316 7800 7800 7250 7100 6950 5800 2720

F-11 7350 7350 7350 7350 7350 2898 504F-22 7224 7224 7224 7224 7098 3192 546

Pressure - Temperature Rating for Series 260 Weld-Inlbs. per sq. inch

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


F-11 6562 6562 6562 6562 6562 2587 450F-22 6450 6450 6450 6450 6337 2850 487


1-1/2” Diameter Weld-In Thermowells

Series 385Weld-In

Series 260Weld-In

260 and 385 Weld-In SeriesTo Order, Please Specify:

1. Complete Type Number2. Material3. Plug & Chain - If Desired

1-800-827-8240 19


A U B

1-1/2” -U 2-1/2 4 2-1/2Dia. -U 4-1/2 6 4-1/2260 -U 7-1/2 9 7-1/2

Weld-In -U10-1/2 12 10-1/2 .260-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 24 22-1/2

Vel

ocity

Rat

ings

of

Wel

ls

6

A ELEMENT LENGTH

1/4

.260 BORE1-1/2 DIA.

1/2 NPSM

DIA.

U INSERTION LENGTH

1-1/2 DIA.

PLUG & CHAIN(OPTIONAL)

5/8

1-3/4

A ELEMENT LENGTH

1/4

.385 BORE1-1/2 DIA.

1/2 NPSM

DIA.

U INSERTION LENGTH

1-1/2 DIA.


49/64

1-3/4

Van Stone Thermowells For 1/4” & 3/8” Diameter Elements

Following are some of the special tests or procedures that we

offer. Please contact your sales representative for additional

cost and delivery.

TestsHydrostatic test

Internally for screwed wells (specify pressure rating)

Externally for flanged and Van Stone

(normally 1.5 times flange rating)

Dye Penetrant test

Ultrasonic test

X-rayper ASME (Code UW51)

Stress Calculationsper ASME PTC 19.3

ProceduresStress Relieving

Solution Annealing

Heat TreatingMeets N.A.C.E. MR-01-75 specification

Passivating

Electropolishing

Full Penetration Weld

Positive Material Identification (PMI)

Source Inspection

Cleaning for Oxygen Service

Stellite #6 and other wear-resistant coatings

Misc.Premium Delivery Service

Stamp or Vibro Etch Tag Number or Heat Number

Certified Mill Test Reports (MTR’s)

Certified Reproducible drawings

Application:260V Series fits standard length 1/4” diameter elements.385V Series fits standard length 3/8” diameter elements.

Connection Size:Standard wells fit 1” and 1 1/2” lap joint flanges. Othersizes also available.

Materials:Carbon Steel (C-1018), A.I.S.I. 304, A.I.S.I. 316 andMonel are standard. Other materials are available.

Backing Flange:When desired, a carbon steel lap flange can be suppliedwith these wells. When ordering, specify flangepressure rating.

Other DimensionsPipe Actual RaisedSize Dia. Face Dia.

Nominal P R

1 1.315 2

1-1/2 1.900 2-7/8

Series 385V

Series 260V

260V and 385V SeriesTo Order, Please Specify:


18 1-800-827-8240

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°

Brass 5000 4200 1000 --- --- --- ---Carbon Steel 5200 5000 4800 4600 3500 1500 ---A.I.S.I. - 304 7000 6200 5600 5400 5200 4500 1650A.I.S.I. - 316 7000 7000 6400 6200 6100 5100 2500

Monel 6500 6000 5400 5300 5200 1500 ---

Pressure - Temperature Ratinglbs. per sq. inch

Elem. Insert. Shank BoreType Number Lgth. Lgth. Dia. Dia.

A U Q B

385V -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .385-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “

7


Well Type Material 2 4 7 10 13 16 22

Carbon Steel 404 184 67.0 34.0 20.6 13.7 7.4(129) (71.2) (42.7)

260V A.I.S.I. 304 & 316 430 192 69.7 35.4 21.5 14.3 7.7(179) (99.3) (59.6)

Monel 350 168 61.0 31.0 18.8 12.5 3.7(143) (79.8) (47.7)

Carbon Steel 410 248 91.3 45.7 27.6 18.5 10.0(152) (84.3) (50.6)

385V A.I.S.I. 304 & 316 444 258 95.2 47.6 28.8 19.3 10.4(211) (117) (70.3)

Monel 338 226 83.3 41.6 25.2 16.9 9.1(168) (93.3) (56.0)



Series 260V/385V

A ELEMENT LENGTH

Q DIA.

U INSERTION LENGTH2-1/4

1/2 NPSM

P DIA.

.385 BORE

FLANGE SIZE & RATINGAS REQUIRED

3/8R RAISED FACE DIA.

7/8

1/4


A U Q B

260V -U 2 4 2 3/4-U 4 6 4 “-U 7 9 7 “ .260-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “

Opt

iona

l Ser

vice

s

Q DIA.

A ELEMENT LENGTH

3/4


1/2 NPSM

P DIA.

.260 BORE



1/4

1 3/4

2 1/2

U INSERTION LENGTH

Q DIA.


1/2 DIA.

.260 BORE

*1THREAD

ALLOWANCE

P NPT

1/2 NPSM

Application:Fits liquid-in-glass thermometers made to S.A.M.A.standards. Tapered bore is made .008 in. oversize toeliminate possibility of thermometer bulb expandinginto the well, thus preventing removal.Also meets federal GG-T-321C standards.

Connection Size:3/4” and 1” NPT are standard. Other sizes availableupon request.

Materials:Carbon Steel (C-1018), Brass (A.S.T.M. B-16), A.I.S.I.304, A.I.S.I. 316, Monel. Many other materials areavailable upon request.

Additional Designs:Other designs of wells to fit this class of thermometerare available. These include socket weld, heavy dutyand flanged types.

Standard Threaded Thermowells For 1/4” Diameter Elements

Application:Standard length, 1/4” Stem, Bi-metal thermometers;#20 gauge thermocouple elements; unarmored liquid-in-glass test thermometers. Other temperature sensingelements having .252 in. maximum diameter.

Connection Size:1/2”, 3/4” and 1” NPT are standard. Other thread sizesare available upon request.

Materials:B r a s s ( A . S . T. M . B - 1 6 ) , C a r b o n S t e e l(C-1018), Stainless Steel A.I.S.I. 304 & A.I.S.I. 316,Monel. Wells are also available in special materials,prices on request.


*Note: On 1/2” NPT externalthreaded wells, the 1” threadallowance and 3/4” wrench allowanced imens ions a r e r eve r sed t oaccommodate the 1/2” NPSM femalethread.

260S and 260L SeriesTo Order, Please Specify:


8 1-800-827-8240

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


Standard Threaded Thermowells For Industrial Glass Thermometers

Series 445LLagging Extension Type



1-800-827-8240 17

External Elem. Insert. ShankThread Type Number Lgth. Lgth. Dia.

P A U Q

1/2”-260S -U 2-1/2 4 2-1/2 ---U 4-1/2 6 4-1/2 5/8-U 7-1/2 9 7-1/2 “

*1/2” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

3/4”-260S -U 2-1/2 4 2-1/2 ---U 4-1/2 6 4-1/2 3/4-U 7-1/2 9 7-1/2 “

3/4” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

1”-260S -U 2-1/2 4 2-1/2 ---U 4-1/2 6 4-1/2 7/8-U 7-1/2 9 7-1/2 “

1” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

External Nom. Lag. Bulb Insert. ShankThread Type Number Bulb Ext. Lgth. Lgth. Dia.

P Lgth. T A U Q

3/4” NPT 3/4”-445L -S 6E 6 2-1/2 6-1/8 2-9/16 ----S 9E 9 3 9-1/8 5-1/16 7/8

-S12E 12 3 12-1/8 8-1/16 “-S18E 18 3 18-1/8 14-1/16 “-S24E 24 3 24-1/8 20-1/16 “

1” NPT 1”-445L -S 6E 6 2-1/2 6-1/8 2-9/16 ----S 9E 9 3 9-1/8 5-1/16 1

-S12E 12 3 12-1/8 8-1/16 “-S18E 18 3 18-1/8 14-1/16 “-S24E 24 3 24-1/8 20-1/16 “

Temperature — °F

Well Type Material 70° 200° 400° 600° 800° 1000°

3/4”-445S Brass 640 575 100 --- --- ---and Carbon Steel 720 690 660 630 480 210

3/4”-445L A.I.S.I. 304 940 850 770 740 720 625(See Note) A.I.S.I. 316 940 940 875 850 840 700

Monel 900 825 740 730 710 210

1”-445S Brass 1470 1320 230 --- --- ---and Carbon Steel 1650 1590 1520 1450 1100 480

1”-445S A.I.S.I. 304 2150 1950 1770 1710 1670 1430(See Note) A.I.S.I. 316 2150 2150 2010 1960 1920 1610

Monel 2070 1900 1700 1690 1640 480


(Note: Wells with 2-9/16 insertion length have three timesthe pressure ratings shown.)





Brass 207 75.5 27.3 13.9 8.4 5.6 4.1 3.0(59.3) (32.2) (19.7)

1/2” - 260S Carbon Steel 290 105 38.2 19.4 11.8 7.8 5.7 4.2and (106) (59) (36.3)

1/2” - 260L A.I.S.I. 304 & 316 300 109 39.5 20.1 12.2 8.1 5.9 4.4(148) (82.2)

Monel 261 95 34.4 17.5 10.5 7.1 5.2 3.8(118) (65.5)

Brass 207 89.1 32.2 16.4 9.9 6.6 4.8 3.6(59.3) (39.8) (23.9)

3/4” - 260S Carbon Steel 290 123 44.9 22.8 13.8 9.3 6.7 4.9and (106) (71.2) (42.7)

3/4” - 260L A.I.S.I. 304 & 316 300 128 46.4 23.6 14.3 9.6 6.9 5.1(148) (99.3)

Monel 261 112 40.6 20.7 12.4 8.3 6.1 4.5(118) (79.8)

Brass 207 102 37.0 18.8 11.4 7.6 5.5 4.1(59.3) (47.6) (28)

1” - 260S Carbon Steel 290 143 51.6 26.2 15.9 10.6 7.6 5.7and (106) (84.3) (50.6)

1” - 260L A.I.S.I. 304 & 316 300 148 53.5 27.2 16.5 11.0 7.9 5.9(148) (117)

Monel 261 128 46.7 23.7 14.4 9.5 6.9 5.1(118) (93.3)

External Nom. Bulb Insert. ShankThread Type Number Bulb Lgth. Lgth. Dia.

P Lgth. A U Q

3/4” NPT 3/4”-445S -S 3-1/2 3-1/2 3-5/8 2-9/16 ----S 6 6 6-1/8 5-1/16 7/8-S 9 9 9-1/8 8-1/16 “-S12 12 12-1/8 11-1/16 “-S18 18 18-1/8 17-1/16 “-S24 24 24-1/8 23-1/16 “

1” NPT 1”-445S -S 3-1/2 3-1/2 3-5/8 2-9/16 ----S 6 6 6-1/8 5-1/16 1-S 9 9 9-1/8 8-1/16 “

-S12 12 12-1/8 11-1/16 “-S18 18 18-1/8 17-1/16 “-S24 24 24-1/8 23-1/16 “



Brass 259 142 55.8 29.8 18.4 12.5 9.0 6.83/4”-445S (52.3) (26.4) (16.6) (12.1) (9.5) (7.8) (6.7)

Carbon Steel 352 198 77.5 41.4 27.8 17.3 12.5 9.5and (94.6) (48.0) (30.1) (22.0) (17.3) (14.2) (12.1)

A.I.S.I. 304 & 316 382 206 80.9 43.2 26.6 18.1 13.1 9.93/4”-445L (131) (66.3) (41.7) (30.2) (24.0)

Monel 277 179 70.3 37.5 23.2 15.7 11.3 8.5(105) (53.1) (33.4) (24.3) (19.1)



Brass 259 156 61.4 32.8 20.2 13.7 9.9 7.51”-445S (76) (38.5) (24.2) (17.7) (13.9) (11.4)

Carbon Steel 352 215 34.2 45.0 27.7 18.9 13.6 10.3and (137) (69.4) (43.6) (31.9) (25.0)

A.I.S.I. 304 & 316 382 224 87.8 46.9 28.9 19.7 14.2 10.81”- 445L (190) (96.1) (60.4) (44.1)

Monel 277 196 77.2 41.4 25.4 17.2 12.4 9.4(152) (77.1) (48.5) (35.4)

Series 445SGeneral Use



External Elem. Insert. Lag. ShankThread Type Number Lgth. Lgth. Ext. Dia.

P A U T Q

1/2”-260L -U 2-1/2 6 2-1/2 2 ---U 4-1/2 9 4-1/2 3 5/8

*1/2” NPT -U 7-1/2 12 7-1/2 3 “-U10-1/2 15 10-1/2 3 “-U13-1/2 18 13-1/2 3 “-U19-1/2 24 19-1/2 3 “

3/4”-260L -U 2-1/2 6 2-1/2 2 ---U 4-1/2 9 4-1/2 3 3/4

3/4” NPT -U 7-1/2 12 7-1/2 3 “-U10-1/2 15 10-1/2 3 “-U13-1/2 18 13-1/2 3 “-U19-1/2 24 19-1/2 3 “

1”-260L -U 2-1/2 6 2-1/2 2 ---U 4-1/2 9 4-1/2 3 7/8

1” NPT -U 7-1/2 12 7-1/2 3 “-U10-1/2 15 10-1/2 3 “-U13-1/2 18 13-1/2 3 “-U19-1/2 24 19-1/2 3 “

T + 1 3/4

2 1/2

U INSERTION LENGTH

Q DIA.


1/2 DIA.

.260 BORE

*1THREAD

ALLOWANCE

P NPT

1/2 NPSM

TLAGGING

EXTENSION

*3/4WRENCH

ALLOWANCE

1THREAD

ALLOWANCE

A BULB LENGTH (ACTUAL)

3/32

TAPER .180/FT.

P NPT

1-1/4-18 NEFTHREAD

13/32MINIMUMTHREAD

U INSERTION LENGTH13/16

2-45/64

25/32 DIA.

Q DIA.

5/8

S=U+1

2-9/16

MIN.5/8 DIA.

.436

5.4

355

DIA

. AT

THEO

RETI

CAL

END

OF T

APE

R

1THREAD

ALLOWANCE

TLAGGING

EXTENSION


3/32

TAPER .180/FT.

P NPT

1-1/4-18 NEFTHREAD

13/32MINIMUMTHREAD


2-45/64

25/32 DIA.

Q DIA.

5/8

S=U+1

2-9/16

MIN.5/8 DIA.

.436

5.4

355

DIA

. AT

THEO

RETI

CAL

END

OF T

APE

R

1-800-827-8240 9

Application:Armored l iquid-in-glass test thermometers#14 gauge test thermocouplesBi-metal test thermometers

Connection Size:1/2” NPT external thread is standard.

Lagging Extension:When extra head length is required to extend throughinsulation, 2 1/2” lagging extension is standard.

Plug & Chain:Brass captive plug and chain is furnished on all wellsas standard.

Materials:B r a s s ( A . S . T. M . B - 1 6 ) ; C a r b o n S t e e l(C-1018); A.I.S.I. 304; A.I.S.I. 316. Other materialsare available upon request.

Application:Used where short insertion length is necessary as inshort legs of tees etc. This well also fits the 2 1/2”length Bi-metal thermometer with 1/4” stem diameter.

Connection Size:3/4” NPT and 1” NPT external thread.1/2” Available. See Note.

Materials:Brass (A.S.T.M. B-16), Carbon Steel (C-1018),A.I.S.I. 304, A.I.S.I. 316, Monel.

Plug & Chain:Brass or Stainless Steel captive plug is available uponspecification.

Heavy Duty Threaded Thermowells For 1/4” Diameter Elements

Application:Standard length, 1/4” Bi-metal thermometers. #20gauge thermocouple elements. Unarmored liquid-in-glass test thermometers. Other temperature sensingelements having .252 in. maximum diameter.

Connection Size:3/4” NPT and 1” NPT are standard. Other thread sizesare available upon request.


Plug & Chain:Brass or Stainless Steel captive plug is availablefor keeping well bore clean when not in use.

260H and 260HL SeriesTo Order, Please Specify:


Limited Space Thermowells For 1/4” Diameter Elements

Series 385A

Series 260A

260A and 385A SeriesTo Order, Please Specify:

1. Complete Type Number2. Material3. Plug & Chain - If Desired on 260A Series

16 1-800-827-8240

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


General Purpose Test Thermowells For 3/8” Diameter Elements

Series 260HLLagging Extension Type


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 7450 6850 6150 6100 5940 1750 ---

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°




Material 2 4 6 8 10 12

Brass 362 115 51.4 28.9 18.5 12.8(74) (37) 24.7) (18.5) (14.8) (12.3)

Carbon Steel 422 155 69.1 38.9 24.9 17.3(156) (78) (52.1)

A.I.S.I. 304 & 316 450 162 72.2 40.6 26.0 18.1(223) (112)

Monel 382 145 64.7 36.4 23.3 16.1(147) (73.8) (49.2)



External ThreadP Type Number

3/4” NPT 3/4” - 260A-U1-5/8”1” NPT 1” - 260A-U1-5/8”

Series 260HGeneral Use


P A U Q

3/4”-260H -U 2-1/2 4 2-1/2 7/8-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

3/4” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

1”-260H -U 2-1/2 4 2-1/2 1-1/16-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

1” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

External Lag. Elem. Insert. ShankThread Type Number Ext. Lgth. Lgth. Dia.

P T A U Q

3/4”-260HL -U 2-1/2 2 6 2-1/2 7/8-U 4-1/2 3 9 4-1/2 “

3/4” NPT -U 7-1/2 3 12 7-1/2 “-U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “

1”-260HL -U 2-1/2 2 6 2-1/2 1-1/16-U 4-1/2 3 9 4-1/2 “

1” NPT -U 7-1/2 3 12 7-1/2 “-U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “



Brass 305 93.8 33.9 17.1 10.5 7.0 5.5 3.7(97.5) (54.1)

3/4” - 260H Carbon Steel 386 180 65.3 33.0 20.1 13.4 9.6 7.1and (175) (97.2) (59.3)

3/4” - 260H L A.I.S.I. 304 & 316 440 197 71.2 36.0 22.0 14.7 10.5 7.8(243) (135)

Monel 354 155 56.1 28.4 17.3 11.6 7.5 5.6(195) (108)

Brass 354 108 39.4 19.8 12.2 8.1 5.8 4.3(161) (89.5)

1” - 260H Carbon Steel 448 209 75.7 38.4 23.3 15.5 11.1 8.2and (289) (161)

1” - 260H L A.I.S.I. 304 & 316 490 228 82.5 41.8 25.5 17.1 12.2 9.1(403) (225)

Monel 410 179 65.1 33.0 20.1 13.5 8.7 6.5(322) (178)



Insert. ElemType Number Lgth. lgth.

U A

1/2”-385A -U 2 2 3-1/4-U 4 4 5-1/4-U 6 6 7-1/4-U 8 8 9-1/4-U10 10 11-1/4-U12 12 13-1/4

Note: 1/2” NPT external threads are available.The “U” dimension becomes 1” to accommodatethe 1/2” NPSM female thread. Specify as:1/2-260A-U1-material.

A ELEMENT LENGTH

5/8 DIA.


1/4 NPT

.385 BORE

3/41/2 NPT

BRASS PLUG& CHAIN

1/4

U INSERTION LENGTH

Q DIA.


5/8DIA.

.260 BOREP NPT

1/2 NPSM 3/4WRENCH

ALLOWANCE

TLAGGING

EXTENSION

1THREAD

ALLOWANCE

1 3/4 U INSERTION LENGTH

Q DIA.

1/4

5/8DIA.

.260 BORE

1THREAD

ALLOWANCE

P NPT

1/2 NPSM

A ELEMENT LENGTH

1-1/16 1-5/8

5/16

.260 BORE

2-1/2 3/16

1/2 NPSM

1/2 DIA

P NPT



InsertionLength - “U”

Well Type Material 1-5/8

Brass 207(59.3)

Carbon Steel 2903/4” - 260A (106)

A.I.S.I. 304 & 316 300(148)

Monel 261(118)

Brass 207(59.3)

Carbon Steel 2901” - 260A (106)

A.I.S.I. 304 & 316 300(148)

Monel 261(118)

Application:260FH Series fits standard length 1/4” diameter elements.385FH Series fits standard length 3/8” diameter elements.

Flange Sizes:1”, 1-1/2” and 2” flanges in all facings and pressureratings are standard. Other sizes are available onapplication. Machined to meet ANSI B-16.5.Traceable to mill test reports.

Materials:Flanges and wells made of Carbon Steel (C-1018),A.I.S.I. 304, A.I.S.I. 316 and Monel are available forquick delivery. Other materials are available.

Welding:Primary weld is “J” groove type, secondary weld is 45°bevel groove. Welding is performed by certified weldersusing inert gas shielded arc.


Lagging Extension:Specifiy as 260FHL or 385FHL. Add “T” lagging to2-1/4” head dimension.

Tapered Flanged Thermowells For 1/4” & 3/8” Diameter Elements

260FH and 385FH SeriesTo Order, Please Specify:


1-800-827-8240 15

Series 385FH

Series 260FH



Carbon Steel 603 227 74.0 36.0 21.0 14.0 7.5260FH (273) (125) (67)

A.I.S.I. 304 & 316 687 249 81.0 39.8 23.6 15.5 8.2(379) (170)

Monel 553 196 64.0 31.0 18.0 12.0 6.0(304) (136)

A.I.S.I. 304 & 316 550 241 78.9 38.0 22.8 15.0 7.9385FH (356) (144)

Carbon Steel 648 257 83.8 41.0 24.0 16.0 8.4(467) (194)

Monel 531 217 71.0 34.8 20.6 13.0 7.0(398) (169)



Note:If higher velocities than shown in table are required, “Q” diametermust be increased. Check with our engineering dept.

Temperature - °F

Material 0° 200° 400° 600° 800° 1000° 1125°

Carbon Steel UP TO 2500#

A.I.S.I. - 304 UP TO 2500#

A.I.S.I. - 316 UP TO 2500#

Monel UP TO 2500#

Maximum Pressure - Temperature Ratinglbs. per sq. inch


Application:Standard length, 3/8” Stem, Bi-metal thermometers;#14 gauge thermocouple elements; Armored liquid-in-glass test thermometers. Other temperature sensingelements having .377 in. maximum diameter.

Connection Size:3/4” and 1” NPT are standard. Other thread sizes areavailable upon request.

Materials:B r a s s ( A . S . T. M . B - 1 6 ) , C a r b o n S t e e l(C-1018), A.I.S.I. 304 & A.I.S.I. 316, Monel. Wellsare also available in special materials, prices on request.




10 1-800-827-8240


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


External Elem. Insert.Thread Type Number Lgth. Lgth.

P A U

3/4”-385S -U 2-1/2 4 2-1/2-U 4-1/2 6 4-1/2

3/4” NPT -U 7-1/2 9 7-1/2-U10-1/2 12 10-1/2-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 22 22-1/2

1”-385S -U 2-1/2 4 2-1/2-U 4-1/2 6 4-1/2

1” NPT -U 7-1/2 9 7-1/2-U10-1/2 12 10-1/2-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 24 22-1/2

External Lag. Elem. Insert.Thread Type Number Ext. Lgth. Lgth.

P T A U

3/4”-385L -U 2-1/2 2 6 2-1/2-U 4-1/2 3 9 4-1/2

3/4” NPT -U 7-1/2 3 12 7-1/2-U10-1/2 3 15 10-1/2-U13-1/2 3 18 13-1/2-U19-1/2 3 24 19-1/2

1”-385L -U 2-1/2 2 6 2-1/2-U 4-1/2 3 9 4-1/2

1” NPT -U 7-1/2 3 12 7-1/2-U10-1/2 3 15 10-1/2-U13-1/2 3 18 13-1/2-U19-1/2 3 24 19-1/2




Material 2-1/2 4-1/2 7-1/2 10-1/2 13-1/2 16-1/2 19-1/2 22-1/2

Brass 290 150 54.1 27.6 16.7 11.1 8.0 6.0(145) (80) (48)

Carbon Steel 326 192 69.5 35.4 20.5 14.3 10.3 7.7(260) (144)

A.I.S.I. 304 & 316 349 199 71.9 36.6 21.2 14.8 10.7 8.0(360)

Monel 316 189 68.1 34.8 20.8 14.0 10.0 7.5(320) (178)


.385 BORE

P NPT

1/2 NPSM


49/64 DIA.

U INSERTION LENGTH1THREAD

ALLOWANCE

TLAGGING

EXTENSION

3/4WRENCH

ALLOWANCE

A ELEMENT LENGTH

.260 BORE

1/2 NPSM

Q DIA.

U INSERTION LENGTH

FLANGE SIZE 8 FACINGAS REQUIRED

WELD

1-1/4

DIA

2-1/4

5/8

1/4A ELEMENT LENGTH

.260 BORE

1/2 NPSM

Q DIA.

U INSERTION LENGTH


WELD

1-1/4

DIA

2-1/4

5/8

1/4



49/64 DIA.

.385 BORE

1THREAD

ALLOWANCE

P NPT

1/2 NPSM



A ELEMENT LENGTH

.385 BORE

1/2 NPSM

Q DIA.

U INSERTION LENGTH


WELD

1-1/4

DIA

2-1/4

49/64

1/4


A U Q B

260FH -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .260-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “


A U Q B

385FH -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .385-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “

A ELEMENT LENGTH

Q DIA.


1/2 NPSM

1-1/4

DIA

.

.260 BORE


WELD

3/4

1/4


Application:Standard length, 3/8” Stem, Bi-metal thermometers.#14 gauge thermocouple elements. Armored liquid-in-glass test thermometers. Other temperature sensingelements having .377 in. maximum diameter.

Connection Size:3/4” and 1” NPT is standard. Other thread sizes areavailable upon request.

Materials:Brass (A.S.T.M. B-16), Carbon Steel (C-1018),A.I.S.I. 304, A.I.S.I. 316, Monel. Wells are alsoavailable in special materials, prices on request.


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


Application:260F Series fits standard length 1/4” diameter elements.385F Series fits standard length 3/8” diameter elements.

Flange:1”, 1-1/2” and 2” flanges in all facings and pressureratings are standard. Other sizes are available onapplication. Machined to meet ANSI B-16.5.Traceable to mill test reports.

Materials:Flanges and wel l s made of Carbon S tee l(C-1018), A.I.S.I. 304, A.I.S.I. 316 and Monel areavailable for quick delivery. Other materials are available.



Lagging Extension:Specifiy as 260FL or 385FL. Add “T” lagging to 2 1/4”head dimensions.

Flanged Thermowells For 1/4” & 3/8” Diameter Elements

260F and 385F SeriesTo Order, Please Specify:


14 1-800-827-8240




1-800-827-8240 11

Series 260F

Series 385F


A U Q B

385F -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .385-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “


A U Q B

260F -U 2 4 2 3/4-U 4 6 4 “-U 7 9 7 “ .260-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “



Brass 276 124 44.0 22.0 13.0 8.0 6.0 4.03/4”-385H (127) (79)

Carbon Steel 352 191 69.0 35.0 21.0 14.0 10.0 7.5and (228) (114)

A.I.S.I. 304 & 316 415 203 73.2 37.3 22.5 15.0 11.0 8.03/4”-385HL (299) (154)

Monel 340 172 62.0 31.0 19.0 12.8 8.0 6.0(255) (134)



Brass 321 129 46.8 23.6 14.5 9.6 6.9 5.11”-385H (150) (83.5)

Carbon Steel 410 249 90.3 45.6 27.8 18.5 13.2 9.8and (270) (150)

A.I.S.I. 304 & 316 483 272 97.3 49.7 30.4 20.3 14.5 10.71”- 385HL (350) (208)

Monel 396 214 77.5 39.2 23.8 16.0 10.3 7.7(306) (167)


P A U Q

3/4”-385H -U 2-1/2 4 2-1/2 7/8-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

3/4” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

1”-385H -U 2-1/2 4 2-1/2 1-1/16-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

1” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “



Carbon Steel 404 184 67.0 34.0 20.6 13.7 7.4(129) (71.2) (42.7)

260F A.I.S.I. 304 & 316 430 192 69.7 35.4 21.5 14.3 7.7(179) (99.3) (59.6)

Monel 350 168 61.0 31.0 18.8 12.5 3.7(143) (79.8) (47.7)

Carbon Steel 410 248 91.3 45.7 27.6 18.5 10.0(152) (84.3) (50.6)

385F A.I.S.I. 304 & 316 444 258 95.2 47.6 28.8 19.3 10.4(211) (117) (70.3)

Monel 338 226 83.3 41.6 25.2 16.9 9.1(168) (93.3) (56.0)



Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1125°


A.I.S.I. - 304 UP TO 2500#

A.I.S.I. - 316 UP TO 2500#

Monel UP TO 2500#

Maximum Flange Pressure - Temperature Ratinglbs. per sq. inch


49/64 DIA.


1/2 NPSM

.385 BORE

1THREAD

ALLOWANCE

P NPT


Q DIA.



P T A U Q

3/4”-385HL -U 2-1/2 2 6 2-1/2 7/8-U 4-1/2 3 9 4-1/2 “-U 7-1/2 3 12 7-1/2 “

3/4” NPT -U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “

1”-385HL -U 2-1/2 2 6 2-1/2 1-1/16-U 4-1/2 3 9 4-1/2 “-U 7-1/2 3 12 7-1/2 “

1” NPT -U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “

TLAGGING

EXTENSION

1THREAD

ALLOWANCE


49/64 DIA.

U INSERTION LENGTH

1/2 NPSM

.385 BORE

P NPT


Q DIA.

3/4WRENCH

ALLOWANCE

1/4A ELEMENT LENGTH

Q DIA.


1/2 NPSM

1-1/4

DIA

.

.385 BORE


WELD

7/8



Carbon Steel 386 180 65.3 33.0 20.1 13.4 9.6 7.13/4”-260WH (175) (97.2) (59.3)

A.I.S.I. 304 & 316 440 197 71.2 36.0 22.0 14.7 10.5 7.8(243) (135)

Carbon Steel 448 209 75.7 38.4 23.3 15.5 11.1 8.21”-260WH (289) (161)

A.I.S.I. 304 & 316 490 228 82.5 41.8 25.5 17.1 12.2 9.1(403) (225)

Carbon Steel 352 191 69.0 35.0 21.0 14.0 10.0 7.53/4”-385WH (228) (114)

A.I.S.I. 304 & 316 415 203 73.2 37.3 22.5 15.0 11.0 8.0(299) (154)

Carbon Steel 410 249 90.3 45.6 27.8 18.5 13.2 9.81”-385WH (270) (150)

A.I.S.I. 304 & 316 483 272 97.3 49.7 30.4 20.3 14.5 10.7(350) (208)



Application:260W Series fits standard length 1/4” diameter elements.385W Series fits standard length 3/8” diameter elements.

Connection Size:3/4” or 1” nominal pipe size welding shoulder fits ANSIwelding fittings, flanges, etc. Wells for larger pipe sizefittings are available on request.

Materials:Carbon Steel C-1018, A.I.S.I. 304, A.I.S.I. 316 arestandard. Other materials are available upon request.

Lagging Extension:When specifying lagging extension, choose a lengthwhich will permit the use of a standard element length.(See 260L and 385L lengths)

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---






Well Type Material 2-1/2 4-1/2 7-1/2 10-1/2 13-1/2 16-1/2 22-1/2

Carbon Steel 290 123 44.9 22.8 13.8 9.3 4.93/4”-260W (106) (71.2) (42.7)

A.I.S.I. 304 & 316 300 128 46.4 23.6 14.3 9.6 5.1(148) (99.3)

Carbon Steel 290 143 51.6 26.2 15.9 10.6 5.71” - 260W (106) (84.3) (50.6)

A.I.S.I. 304 & 316 300 148 53.5 27.2 16.5 11.0 5.9(148) (117)

3/4”-385W Carbon Steel 426 192 69.5 35.4 20.5 14.6 7.7and (260) (144)

1”-385W A.I.S.I. 304 & 316 449 199 71.9 36.6 21.2 14.8 8.0(360)

Socket-Weld Design Thermowells For 1/4” & 3/8” Diameter Elements

260W and 385W SeriesTo Order, Please Specify:


12 1-800-827-8240

Series 385W

Series 260W

Pipe Shank Elem. Insert.Size Type Number Dia. Lgth. Lgth.

P Q P A U

3/4”-260W -U 2-1/2 -- 1.050 4 2-1/23/4” -U 4-1/2 3/4 “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

1”-260W -U 2-1/2 -- 1.315 4 2-1/21” -U 4-1/2 7/8 “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

Series 385WH

Series 260WH

260WH and 385WH SeriesTo Order, Please Specify:


1-800-827-8240 13

Pipe Elem. Insert.Size Type Number Lgth. Lgth.

P P A U

3/4”-385W -U 2-1/2 1.050 4 2-1/23/4” -U 4-1/2 “ 6 4-1/2

Nominal -U 7-1/2 “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ 12 10-1/2

-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2

1”-385W -U 2-1/2 1.315 4 2-1/21” -U 4-1/2 “ 6 4-1/2

Nominal -U 7-1/2 “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ 12 10-1/2

-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2

Heavy Duty Socket-Weld For 1/4” & 3/8” Diameter Elements

Application:260WH Series fits standard length 1/4” diameter elements.385WH Series fits standard length 3/8” diameter elements.






P Q P A U

3/4”-385WH -U 2-1/2 7/8 1.050 4 2-1/23/4” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

1”-385WH -U 2-1/2 1 1.315 4 2-1/21” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2


P Q P A U

3/4”-260WH -U 2-1/2 7/8 1.050 4 2-1/23/4” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

1”-260WH -U 2-1/2 1 1.315 4 2-1/21” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°

Carbon Steel 5200 5000 4800 4600 3500 1500 ---A.I.S.I. - 304 7000 6200 5600 5400 5200 4500 1650A.I.S.I. - 316 7000 7000 6400 6200 6100 5100 2500

Pressure - Temperature Rating for 385WHlbs. per sq. inch

1/4A ELEMENT LENGTH

49/64 DIA.


1/2 NPSM

.385 BORE

Q DIA.

PPIPESIZE

A ELEMENT LENGTH

Q


PPIPESIZE

1/4

5/8

A ELEMENT LENGTH


PPIPESIZE

Q

1/4

49/64


.260 BORE

Q DIA.

1/2 NPSM

1/2 DIA.


PPI

PE S

IZE

2-1/2


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°




Carbon Steel 386 180 65.3 33.0 20.1 13.4 9.6 7.13/4”-260WH (175) (97.2) (59.3)

A.I.S.I. 304 & 316 440 197 71.2 36.0 22.0 14.7 10.5 7.8(243) (135)

Carbon Steel 448 209 75.7 38.4 23.3 15.5 11.1 8.21”-260WH (289) (161)

A.I.S.I. 304 & 316 490 228 82.5 41.8 25.5 17.1 12.2 9.1(403) (225)

Carbon Steel 352 191 69.0 35.0 21.0 14.0 10.0 7.53/4”-385WH (228) (114)

A.I.S.I. 304 & 316 415 203 73.2 37.3 22.5 15.0 11.0 8.0(299) (154)

Carbon Steel 410 249 90.3 45.6 27.8 18.5 13.2 9.81”-385WH (270) (150)

A.I.S.I. 304 & 316 483 272 97.3 49.7 30.4 20.3 14.5 10.7(350) (208)



Application:260W Series fits standard length 1/4” diameter elements.385W Series fits standard length 3/8” diameter elements.




Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---






Well Type Material 2-1/2 4-1/2 7-1/2 10-1/2 13-1/2 16-1/2 22-1/2

Carbon Steel 290 123 44.9 22.8 13.8 9.3 4.93/4”-260W (106) (71.2) (42.7)

A.I.S.I. 304 & 316 300 128 46.4 23.6 14.3 9.6 5.1(148) (99.3)

Carbon Steel 290 143 51.6 26.2 15.9 10.6 5.71” - 260W (106) (84.3) (50.6)

A.I.S.I. 304 & 316 300 148 53.5 27.2 16.5 11.0 5.9(148) (117)

3/4”-385W Carbon Steel 426 192 69.5 35.4 20.5 14.6 7.7and (260) (144)

1”-385W A.I.S.I. 304 & 316 449 199 71.9 36.6 21.2 14.8 8.0(360)

Socket-Weld Design Thermowells For 1/4” & 3/8” Diameter Elements

260W and 385W SeriesTo Order, Please Specify:


12 1-800-827-8240

Series 385W

Series 260W


P Q P A U

3/4”-260W -U 2-1/2 -- 1.050 4 2-1/23/4” -U 4-1/2 3/4 “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

1”-260W -U 2-1/2 -- 1.315 4 2-1/21” -U 4-1/2 7/8 “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

Series 385WH

Series 260WH

260WH and 385WH SeriesTo Order, Please Specify:


1-800-827-8240 13

Pipe Elem. Insert.Size Type Number Lgth. Lgth.

P P A U

3/4”-385W -U 2-1/2 1.050 4 2-1/23/4” -U 4-1/2 “ 6 4-1/2

Nominal -U 7-1/2 “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ 12 10-1/2

-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2

1”-385W -U 2-1/2 1.315 4 2-1/21” -U 4-1/2 “ 6 4-1/2

Nominal -U 7-1/2 “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ 12 10-1/2

-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2

Heavy Duty Socket-Weld For 1/4” & 3/8” Diameter Elements

Application:260WH Series fits standard length 1/4” diameter elements.385WH Series fits standard length 3/8” diameter elements.






P Q P A U

3/4”-385WH -U 2-1/2 7/8 1.050 4 2-1/23/4” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

1”-385WH -U 2-1/2 1 1.315 4 2-1/21” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2


P Q P A U

3/4”-260WH -U 2-1/2 7/8 1.050 4 2-1/23/4” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.050 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

1”-260WH -U 2-1/2 1 1.315 4 2-1/21” -U 4-1/2 “ “ 6 4-1/2

Nominal -U 7-1/2 “ “ 9 7-1/2(1.315 Dia.) -U10-1/2 “ “ 12 10-1/2

-U13-1/2 “ “ 15 13-1/2-U16-1/2 “ “ 18 16-1/2-U22-1/2 “ “ 24 22-1/2

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°



1/4A ELEMENT LENGTH

49/64 DIA.


1/2 NPSM

.385 BORE

Q DIA.

PPIPESIZE

A ELEMENT LENGTH

Q


PPIPESIZE

1/4

5/8

A ELEMENT LENGTH


PPIPESIZE

Q

1/4

49/64


.260 BORE

Q DIA.

1/2 NPSM

1/2 DIA.


PPI

PE S

IZE

2-1/2


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


A ELEMENT LENGTH

Q DIA.


1/2 NPSM

1-1/4

DIA

.

.260 BORE


WELD

3/4

1/4


Application:Standard length, 3/8” Stem, Bi-metal thermometers.#14 gauge thermocouple elements. Armored liquid-in-glass test thermometers. Other temperature sensingelements having .377 in. maximum diameter.

Connection Size:3/4” and 1” NPT is standard. Other thread sizes areavailable upon request.

Materials:Brass (A.S.T.M. B-16), Carbon Steel (C-1018),A.I.S.I. 304, A.I.S.I. 316, Monel. Wells are alsoavailable in special materials, prices on request.


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


Application:260F Series fits standard length 1/4” diameter elements.385F Series fits standard length 3/8” diameter elements.

Flange:1”, 1-1/2” and 2” flanges in all facings and pressureratings are standard. Other sizes are available onapplication. Machined to meet ANSI B-16.5.Traceable to mill test reports.

Materials:Flanges and wel l s made of Carbon S tee l(C-1018), A.I.S.I. 304, A.I.S.I. 316 and Monel areavailable for quick delivery. Other materials are available.



Lagging Extension:Specifiy as 260FL or 385FL. Add “T” lagging to 2 1/4”head dimensions.

Flanged Thermowells For 1/4” & 3/8” Diameter Elements

260F and 385F SeriesTo Order, Please Specify:


14 1-800-827-8240




1-800-827-8240 11

Series 260F

Series 385F


A U Q B

385F -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .385-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “


A U Q B

260F -U 2 4 2 3/4-U 4 6 4 “-U 7 9 7 “ .260-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “



Brass 276 124 44.0 22.0 13.0 8.0 6.0 4.03/4”-385H (127) (79)

Carbon Steel 352 191 69.0 35.0 21.0 14.0 10.0 7.5and (228) (114)

A.I.S.I. 304 & 316 415 203 73.2 37.3 22.5 15.0 11.0 8.03/4”-385HL (299) (154)

Monel 340 172 62.0 31.0 19.0 12.8 8.0 6.0(255) (134)



Brass 321 129 46.8 23.6 14.5 9.6 6.9 5.11”-385H (150) (83.5)

Carbon Steel 410 249 90.3 45.6 27.8 18.5 13.2 9.8and (270) (150)

A.I.S.I. 304 & 316 483 272 97.3 49.7 30.4 20.3 14.5 10.71”- 385HL (350) (208)

Monel 396 214 77.5 39.2 23.8 16.0 10.3 7.7(306) (167)


P A U Q

3/4”-385H -U 2-1/2 4 2-1/2 7/8-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

3/4” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

1”-385H -U 2-1/2 4 2-1/2 1-1/16-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

1” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “



Carbon Steel 404 184 67.0 34.0 20.6 13.7 7.4(129) (71.2) (42.7)

260F A.I.S.I. 304 & 316 430 192 69.7 35.4 21.5 14.3 7.7(179) (99.3) (59.6)

Monel 350 168 61.0 31.0 18.8 12.5 3.7(143) (79.8) (47.7)

Carbon Steel 410 248 91.3 45.7 27.6 18.5 10.0(152) (84.3) (50.6)

385F A.I.S.I. 304 & 316 444 258 95.2 47.6 28.8 19.3 10.4(211) (117) (70.3)

Monel 338 226 83.3 41.6 25.2 16.9 9.1(168) (93.3) (56.0)



Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1125°


A.I.S.I. - 304 UP TO 2500#

A.I.S.I. - 316 UP TO 2500#

Monel UP TO 2500#

Maximum Flange Pressure - Temperature Ratinglbs. per sq. inch


49/64 DIA.


1/2 NPSM

.385 BORE

1THREAD

ALLOWANCE

P NPT


Q DIA.



P T A U Q

3/4”-385HL -U 2-1/2 2 6 2-1/2 7/8-U 4-1/2 3 9 4-1/2 “-U 7-1/2 3 12 7-1/2 “

3/4” NPT -U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “

1”-385HL -U 2-1/2 2 6 2-1/2 1-1/16-U 4-1/2 3 9 4-1/2 “-U 7-1/2 3 12 7-1/2 “

1” NPT -U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “

TLAGGING

EXTENSION

1THREAD

ALLOWANCE


49/64 DIA.

U INSERTION LENGTH

1/2 NPSM

.385 BORE

P NPT


Q DIA.

3/4WRENCH

ALLOWANCE

1/4A ELEMENT LENGTH

Q DIA.


1/2 NPSM

1-1/4

DIA

.

.385 BORE


WELD

7/8

Application:260FH Series fits standard length 1/4” diameter elements.385FH Series fits standard length 3/8” diameter elements.

Flange Sizes:1”, 1-1/2” and 2” flanges in all facings and pressureratings are standard. Other sizes are available onapplication. Machined to meet ANSI B-16.5.Traceable to mill test reports.

Materials:Flanges and wells made of Carbon Steel (C-1018),A.I.S.I. 304, A.I.S.I. 316 and Monel are available forquick delivery. Other materials are available.



Lagging Extension:Specifiy as 260FHL or 385FHL. Add “T” lagging to2-1/4” head dimension.

Tapered Flanged Thermowells For 1/4” & 3/8” Diameter Elements

260FH and 385FH SeriesTo Order, Please Specify:


1-800-827-8240 15

Series 385FH

Series 260FH



Carbon Steel 603 227 74.0 36.0 21.0 14.0 7.5260FH (273) (125) (67)

A.I.S.I. 304 & 316 687 249 81.0 39.8 23.6 15.5 8.2(379) (170)

Monel 553 196 64.0 31.0 18.0 12.0 6.0(304) (136)

A.I.S.I. 304 & 316 550 241 78.9 38.0 22.8 15.0 7.9385FH (356) (144)

Carbon Steel 648 257 83.8 41.0 24.0 16.0 8.4(467) (194)

Monel 531 217 71.0 34.8 20.6 13.0 7.0(398) (169)



Note:If higher velocities than shown in table are required, “Q” diametermust be increased. Check with our engineering dept.

Temperature - °F

Material 0° 200° 400° 600° 800° 1000° 1125°


A.I.S.I. - 304 UP TO 2500#

A.I.S.I. - 316 UP TO 2500#

Monel UP TO 2500#

Maximum Pressure - Temperature Ratinglbs. per sq. inch


Application:Standard length, 3/8” Stem, Bi-metal thermometers;#14 gauge thermocouple elements; Armored liquid-in-glass test thermometers. Other temperature sensingelements having .377 in. maximum diameter.

Connection Size:3/4” and 1” NPT are standard. Other thread sizes areavailable upon request.

Materials:B r a s s ( A . S . T. M . B - 1 6 ) , C a r b o n S t e e l(C-1018), A.I.S.I. 304 & A.I.S.I. 316, Monel. Wellsare also available in special materials, prices on request.




10 1-800-827-8240


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


External Elem. Insert.Thread Type Number Lgth. Lgth.

P A U

3/4”-385S -U 2-1/2 4 2-1/2-U 4-1/2 6 4-1/2

3/4” NPT -U 7-1/2 9 7-1/2-U10-1/2 12 10-1/2-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 22 22-1/2

1”-385S -U 2-1/2 4 2-1/2-U 4-1/2 6 4-1/2

1” NPT -U 7-1/2 9 7-1/2-U10-1/2 12 10-1/2-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 24 22-1/2

External Lag. Elem. Insert.Thread Type Number Ext. Lgth. Lgth.

P T A U

3/4”-385L -U 2-1/2 2 6 2-1/2-U 4-1/2 3 9 4-1/2

3/4” NPT -U 7-1/2 3 12 7-1/2-U10-1/2 3 15 10-1/2-U13-1/2 3 18 13-1/2-U19-1/2 3 24 19-1/2

1”-385L -U 2-1/2 2 6 2-1/2-U 4-1/2 3 9 4-1/2

1” NPT -U 7-1/2 3 12 7-1/2-U10-1/2 3 15 10-1/2-U13-1/2 3 18 13-1/2-U19-1/2 3 24 19-1/2




Material 2-1/2 4-1/2 7-1/2 10-1/2 13-1/2 16-1/2 19-1/2 22-1/2

Brass 290 150 54.1 27.6 16.7 11.1 8.0 6.0(145) (80) (48)

Carbon Steel 326 192 69.5 35.4 20.5 14.3 10.3 7.7(260) (144)

A.I.S.I. 304 & 316 349 199 71.9 36.6 21.2 14.8 10.7 8.0(360)

Monel 316 189 68.1 34.8 20.8 14.0 10.0 7.5(320) (178)


.385 BORE

P NPT

1/2 NPSM


49/64 DIA.

U INSERTION LENGTH1THREAD

ALLOWANCE

TLAGGING

EXTENSION

3/4WRENCH

ALLOWANCE

A ELEMENT LENGTH

.260 BORE

1/2 NPSM

Q DIA.

U INSERTION LENGTH


WELD

1-1/4

DIA

2-1/4

5/8

1/4A ELEMENT LENGTH

.260 BORE

1/2 NPSM

Q DIA.

U INSERTION LENGTH


WELD

1-1/4

DIA

2-1/4

5/8

1/4



49/64 DIA.

.385 BORE

1THREAD

ALLOWANCE

P NPT

1/2 NPSM



A ELEMENT LENGTH

.385 BORE

1/2 NPSM

Q DIA.

U INSERTION LENGTH


WELD

1-1/4

DIA

2-1/4

49/64

1/4


A U Q B

260FH -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .260-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “


A U Q B

385FH -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .385-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “

1-800-827-8240 9

Application:Armored l iquid-in-glass test thermometers#14 gauge test thermocouplesBi-metal test thermometers

Connection Size:1/2” NPT external thread is standard.

Lagging Extension:When extra head length is required to extend throughinsulation, 2 1/2” lagging extension is standard.

Plug & Chain:Brass captive plug and chain is furnished on all wellsas standard.

Materials:B r a s s ( A . S . T. M . B - 1 6 ) ; C a r b o n S t e e l(C-1018); A.I.S.I. 304; A.I.S.I. 316. Other materialsare available upon request.

Application:Used where short insertion length is necessary as inshort legs of tees etc. This well also fits the 2 1/2”length Bi-metal thermometer with 1/4” stem diameter.

Connection Size:3/4” NPT and 1” NPT external thread.1/2” Available. See Note.

Materials:Brass (A.S.T.M. B-16), Carbon Steel (C-1018),A.I.S.I. 304, A.I.S.I. 316, Monel.

Plug & Chain:Brass or Stainless Steel captive plug is available uponspecification.


Application:Standard length, 1/4” Bi-metal thermometers. #20gauge thermocouple elements. Unarmored liquid-in-glass test thermometers. Other temperature sensingelements having .252 in. maximum diameter.

Connection Size:3/4” NPT and 1” NPT are standard. Other thread sizesare available upon request.





Limited Space Thermowells For 1/4” Diameter Elements

Series 385A

Series 260A

260A and 385A SeriesTo Order, Please Specify:

1. Complete Type Number2. Material3. Plug & Chain - If Desired on 260A Series

16 1-800-827-8240

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


General Purpose Test Thermowells For 3/8” Diameter Elements



Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 7450 6850 6150 6100 5940 1750 ---

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°




Material 2 4 6 8 10 12

Brass 362 115 51.4 28.9 18.5 12.8(74) (37) 24.7) (18.5) (14.8) (12.3)

Carbon Steel 422 155 69.1 38.9 24.9 17.3(156) (78) (52.1)

A.I.S.I. 304 & 316 450 162 72.2 40.6 26.0 18.1(223) (112)

Monel 382 145 64.7 36.4 23.3 16.1(147) (73.8) (49.2)



External ThreadP Type Number

3/4” NPT 3/4” - 260A-U1-5/8”1” NPT 1” - 260A-U1-5/8”



P A U Q

3/4”-260H -U 2-1/2 4 2-1/2 7/8-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

3/4” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

1”-260H -U 2-1/2 4 2-1/2 1-1/16-U 4-1/2 6 4-1/2 “-U 7-1/2 9 7-1/2 “

1” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “


P T A U Q

3/4”-260HL -U 2-1/2 2 6 2-1/2 7/8-U 4-1/2 3 9 4-1/2 “

3/4” NPT -U 7-1/2 3 12 7-1/2 “-U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “

1”-260HL -U 2-1/2 2 6 2-1/2 1-1/16-U 4-1/2 3 9 4-1/2 “

1” NPT -U 7-1/2 3 12 7-1/2 “-U10-1/2 3 15 10-1/2 “-U13-1/2 3 18 13-1/2 “-U19-1/2 3 24 19-1/2 “



Brass 305 93.8 33.9 17.1 10.5 7.0 5.5 3.7(97.5) (54.1)

3/4” - 260H Carbon Steel 386 180 65.3 33.0 20.1 13.4 9.6 7.1and (175) (97.2) (59.3)

3/4” - 260H L A.I.S.I. 304 & 316 440 197 71.2 36.0 22.0 14.7 10.5 7.8(243) (135)

Monel 354 155 56.1 28.4 17.3 11.6 7.5 5.6(195) (108)

Brass 354 108 39.4 19.8 12.2 8.1 5.8 4.3(161) (89.5)

1” - 260H Carbon Steel 448 209 75.7 38.4 23.3 15.5 11.1 8.2and (289) (161)

1” - 260H L A.I.S.I. 304 & 316 490 228 82.5 41.8 25.5 17.1 12.2 9.1(403) (225)

Monel 410 179 65.1 33.0 20.1 13.5 8.7 6.5(322) (178)



Insert. ElemType Number Lgth. lgth.

U A

1/2”-385A -U 2 2 3-1/4-U 4 4 5-1/4-U 6 6 7-1/4-U 8 8 9-1/4-U10 10 11-1/4-U12 12 13-1/4

Note: 1/2” NPT external threads are available.The “U” dimension becomes 1” to accommodatethe 1/2” NPSM female thread. Specify as:1/2-260A-U1-material.

A ELEMENT LENGTH

5/8 DIA.


1/4 NPT

.385 BORE

3/41/2 NPT

BRASS PLUG& CHAIN

1/4

U INSERTION LENGTH

Q DIA.


5/8DIA.

.260 BOREP NPT

1/2 NPSM 3/4WRENCH

ALLOWANCE

TLAGGING

EXTENSION

1THREAD

ALLOWANCE


Q DIA.

1/4

5/8DIA.

.260 BORE

1THREAD

ALLOWANCE

P NPT

1/2 NPSM

A ELEMENT LENGTH

1-1/16 1-5/8

5/16

.260 BORE

2-1/2 3/16

1/2 NPSM

1/2 DIA

P NPT



InsertionLength - “U”

Well Type Material 1-5/8

Brass 207(59.3)

Carbon Steel 2903/4” - 260A (106)

A.I.S.I. 304 & 316 300(148)

Monel 261(118)

Brass 207(59.3)

Carbon Steel 2901” - 260A (106)

A.I.S.I. 304 & 316 300(148)

Monel 261(118)

1 3/4

2 1/2

U INSERTION LENGTH

Q DIA.


1/2 DIA.

.260 BORE

*1THREAD

ALLOWANCE

P NPT

1/2 NPSM

Application:Fits liquid-in-glass thermometers made to S.A.M.A.standards. Tapered bore is made .008 in. oversize toeliminate possibility of thermometer bulb expandinginto the well, thus preventing removal.Also meets federal GG-T-321C standards.

Connection Size:3/4” and 1” NPT are standard. Other sizes availableupon request.

Materials:Carbon Steel (C-1018), Brass (A.S.T.M. B-16), A.I.S.I.304, A.I.S.I. 316, Monel. Many other materials areavailable upon request.

Additional Designs:Other designs of wells to fit this class of thermometerare available. These include socket weld, heavy dutyand flanged types.


Application:Standard length, 1/4” Stem, Bi-metal thermometers;#20 gauge thermocouple elements; unarmored liquid-in-glass test thermometers. Other temperature sensingelements having .252 in. maximum diameter.

Connection Size:1/2”, 3/4” and 1” NPT are standard. Other thread sizesare available upon request.



*Note: On 1/2” NPT externalthreaded wells, the 1” threadallowance and 3/4” wrench allowanced imens ions a r e r eve r sed t oaccommodate the 1/2” NPSM femalethread.



8 1-800-827-8240

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---


Standard Threaded Thermowells For Industrial Glass Thermometers




1-800-827-8240 17


P A U Q

1/2”-260S -U 2-1/2 4 2-1/2 ---U 4-1/2 6 4-1/2 5/8-U 7-1/2 9 7-1/2 “

*1/2” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

3/4”-260S -U 2-1/2 4 2-1/2 ---U 4-1/2 6 4-1/2 3/4-U 7-1/2 9 7-1/2 “

3/4” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

1”-260S -U 2-1/2 4 2-1/2 ---U 4-1/2 6 4-1/2 7/8-U 7-1/2 9 7-1/2 “

1” NPT -U10-1/2 12 10-1/2 “-U13-1/2 15 13-1/2 “-U16-1/2 18 16-1/2 “-U22-1/2 24 22-1/2 “

External Nom. Lag. Bulb Insert. ShankThread Type Number Bulb Ext. Lgth. Lgth. Dia.

P Lgth. T A U Q

3/4” NPT 3/4”-445L -S 6E 6 2-1/2 6-1/8 2-9/16 ----S 9E 9 3 9-1/8 5-1/16 7/8

-S12E 12 3 12-1/8 8-1/16 “-S18E 18 3 18-1/8 14-1/16 “-S24E 24 3 24-1/8 20-1/16 “

1” NPT 1”-445L -S 6E 6 2-1/2 6-1/8 2-9/16 ----S 9E 9 3 9-1/8 5-1/16 1

-S12E 12 3 12-1/8 8-1/16 “-S18E 18 3 18-1/8 14-1/16 “-S24E 24 3 24-1/8 20-1/16 “

Temperature — °F

Well Type Material 70° 200° 400° 600° 800° 1000°

3/4”-445S Brass 640 575 100 --- --- ---and Carbon Steel 720 690 660 630 480 210

3/4”-445L A.I.S.I. 304 940 850 770 740 720 625(See Note) A.I.S.I. 316 940 940 875 850 840 700

Monel 900 825 740 730 710 210

1”-445S Brass 1470 1320 230 --- --- ---and Carbon Steel 1650 1590 1520 1450 1100 480

1”-445S A.I.S.I. 304 2150 1950 1770 1710 1670 1430(See Note) A.I.S.I. 316 2150 2150 2010 1960 1920 1610

Monel 2070 1900 1700 1690 1640 480


(Note: Wells with 2-9/16 insertion length have three timesthe pressure ratings shown.)





Brass 207 75.5 27.3 13.9 8.4 5.6 4.1 3.0(59.3) (32.2) (19.7)

1/2” - 260S Carbon Steel 290 105 38.2 19.4 11.8 7.8 5.7 4.2and (106) (59) (36.3)

1/2” - 260L A.I.S.I. 304 & 316 300 109 39.5 20.1 12.2 8.1 5.9 4.4(148) (82.2)

Monel 261 95 34.4 17.5 10.5 7.1 5.2 3.8(118) (65.5)

Brass 207 89.1 32.2 16.4 9.9 6.6 4.8 3.6(59.3) (39.8) (23.9)

3/4” - 260S Carbon Steel 290 123 44.9 22.8 13.8 9.3 6.7 4.9and (106) (71.2) (42.7)

3/4” - 260L A.I.S.I. 304 & 316 300 128 46.4 23.6 14.3 9.6 6.9 5.1(148) (99.3)

Monel 261 112 40.6 20.7 12.4 8.3 6.1 4.5(118) (79.8)

Brass 207 102 37.0 18.8 11.4 7.6 5.5 4.1(59.3) (47.6) (28)

1” - 260S Carbon Steel 290 143 51.6 26.2 15.9 10.6 7.6 5.7and (106) (84.3) (50.6)

1” - 260L A.I.S.I. 304 & 316 300 148 53.5 27.2 16.5 11.0 7.9 5.9(148) (117)

Monel 261 128 46.7 23.7 14.4 9.5 6.9 5.1(118) (93.3)

External Nom. Bulb Insert. ShankThread Type Number Bulb Lgth. Lgth. Dia.

P Lgth. A U Q

3/4” NPT 3/4”-445S -S 3-1/2 3-1/2 3-5/8 2-9/16 ----S 6 6 6-1/8 5-1/16 7/8-S 9 9 9-1/8 8-1/16 “-S12 12 12-1/8 11-1/16 “-S18 18 18-1/8 17-1/16 “-S24 24 24-1/8 23-1/16 “

1” NPT 1”-445S -S 3-1/2 3-1/2 3-5/8 2-9/16 ----S 6 6 6-1/8 5-1/16 1-S 9 9 9-1/8 8-1/16 “

-S12 12 12-1/8 11-1/16 “-S18 18 18-1/8 17-1/16 “-S24 24 24-1/8 23-1/16 “



Brass 259 142 55.8 29.8 18.4 12.5 9.0 6.83/4”-445S (52.3) (26.4) (16.6) (12.1) (9.5) (7.8) (6.7)

Carbon Steel 352 198 77.5 41.4 27.8 17.3 12.5 9.5and (94.6) (48.0) (30.1) (22.0) (17.3) (14.2) (12.1)

A.I.S.I. 304 & 316 382 206 80.9 43.2 26.6 18.1 13.1 9.93/4”-445L (131) (66.3) (41.7) (30.2) (24.0)

Monel 277 179 70.3 37.5 23.2 15.7 11.3 8.5(105) (53.1) (33.4) (24.3) (19.1)



Brass 259 156 61.4 32.8 20.2 13.7 9.9 7.51”-445S (76) (38.5) (24.2) (17.7) (13.9) (11.4)

Carbon Steel 352 215 34.2 45.0 27.7 18.9 13.6 10.3and (137) (69.4) (43.6) (31.9) (25.0)

A.I.S.I. 304 & 316 382 224 87.8 46.9 28.9 19.7 14.2 10.81”- 445L (190) (96.1) (60.4) (44.1)

Monel 277 196 77.2 41.4 25.4 17.2 12.4 9.4(152) (77.1) (48.5) (35.4)




External Elem. Insert. Lag. ShankThread Type Number Lgth. Lgth. Ext. Dia.

P A U T Q

1/2”-260L -U 2-1/2 6 2-1/2 2 ---U 4-1/2 9 4-1/2 3 5/8

*1/2” NPT -U 7-1/2 12 7-1/2 3 “-U10-1/2 15 10-1/2 3 “-U13-1/2 18 13-1/2 3 “-U19-1/2 24 19-1/2 3 “

3/4”-260L -U 2-1/2 6 2-1/2 2 ---U 4-1/2 9 4-1/2 3 3/4

3/4” NPT -U 7-1/2 12 7-1/2 3 “-U10-1/2 15 10-1/2 3 “-U13-1/2 18 13-1/2 3 “-U19-1/2 24 19-1/2 3 “

1”-260L -U 2-1/2 6 2-1/2 2 ---U 4-1/2 9 4-1/2 3 7/8

1” NPT -U 7-1/2 12 7-1/2 3 “-U10-1/2 15 10-1/2 3 “-U13-1/2 18 13-1/2 3 “-U19-1/2 24 19-1/2 3 “

T + 1 3/4

2 1/2

U INSERTION LENGTH

Q DIA.


1/2 DIA.

.260 BORE

*1THREAD

ALLOWANCE

P NPT

1/2 NPSM

TLAGGING

EXTENSION

*3/4WRENCH

ALLOWANCE

1THREAD

ALLOWANCE


3/32

TAPER .180/FT.

P NPT

1-1/4-18 NEFTHREAD

13/32MINIMUMTHREAD


2-45/64

25/32 DIA.

Q DIA.

5/8

S=U+1

2-9/16

MIN.5/8 DIA.

.436

5.4

355

DIA

. AT

THEO

RETI

CAL

END

OF T

APE

R

1THREAD

ALLOWANCE

TLAGGING

EXTENSION


3/32

TAPER .180/FT.

P NPT

1-1/4-18 NEFTHREAD

13/32MINIMUMTHREAD


2-45/64

25/32 DIA.

Q DIA.

5/8

S=U+1

2-9/16

MIN.5/8 DIA.

.436

5.4

355

DIA

. AT

THEO

RETI

CAL

END

OF T

APE

R

Van Stone Thermowells For 1/4” & 3/8” Diameter Elements

Following are some of the special tests or procedures that we

offer. Please contact your sales representative for additional

cost and delivery.

TestsHydrostatic test

Internally for screwed wells (specify pressure rating)

Externally for flanged and Van Stone

(normally 1.5 times flange rating)

Dye Penetrant test

Ultrasonic test

X-rayper ASME (Code UW51)

Stress Calculationsper ASME PTC 19.3

ProceduresStress Relieving

Solution Annealing

Heat TreatingMeets N.A.C.E. MR-01-75 specification

Passivating

Electropolishing

Full Penetration Weld

Positive Material Identification (PMI)

Source Inspection

Cleaning for Oxygen Service

Stellite #6 and other wear-resistant coatings

Misc.Premium Delivery Service

Stamp or Vibro Etch Tag Number or Heat Number

Certified Mill Test Reports (MTR’s)

Certified Reproducible drawings

Application:260V Series fits standard length 1/4” diameter elements.385V Series fits standard length 3/8” diameter elements.

Connection Size:Standard wells fit 1” and 1 1/2” lap joint flanges. Othersizes also available.

Materials:Carbon Steel (C-1018), A.I.S.I. 304, A.I.S.I. 316 andMonel are standard. Other materials are available.

Backing Flange:When desired, a carbon steel lap flange can be suppliedwith these wells. When ordering, specify flangepressure rating.

Other DimensionsPipe Actual RaisedSize Dia. Face Dia.

Nominal P R

1 1.315 2

1-1/2 1.900 2-7/8

Series 385V

Series 260V

260V and 385V SeriesTo Order, Please Specify:


18 1-800-827-8240

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


Monel 6500 6000 5400 5300 5200 1500 ---



A U Q B

385V -U 2 4 2 7/8-U 4 6 4 “-U 7 9 7 “ .385-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “

7



Carbon Steel 404 184 67.0 34.0 20.6 13.7 7.4(129) (71.2) (42.7)

260V A.I.S.I. 304 & 316 430 192 69.7 35.4 21.5 14.3 7.7(179) (99.3) (59.6)

Monel 350 168 61.0 31.0 18.8 12.5 3.7(143) (79.8) (47.7)

Carbon Steel 410 248 91.3 45.7 27.6 18.5 10.0(152) (84.3) (50.6)

385V A.I.S.I. 304 & 316 444 258 95.2 47.6 28.8 19.3 10.4(211) (117) (70.3)

Monel 338 226 83.3 41.6 25.2 16.9 9.1(168) (93.3) (56.0)



Series 260V/385V

A ELEMENT LENGTH

Q DIA.


1/2 NPSM

P DIA.

.385 BORE



7/8

1/4


A U Q B

260V -U 2 4 2 3/4-U 4 6 4 “-U 7 9 7 “ .260-U10 12 10 “-U13 15 13 “-U16 18 16 “-U22 24 22 “

Opt

iona

l Ser

vice

s

Q DIA.

A ELEMENT LENGTH

3/4


1/2 NPSM

P DIA.

.260 BORE



1/4

Well failures, in most cases, are not due to the effect of pressure and temperature.

The calculations necessary to provide adequate strength, under given conditions,

are familiar enough to permit proper choice of wall thickness and material.

Less familiar, and more dangerous, are the vibrational effects to which wells

are subjected. Fluid, flowing by the well, forms a turbulent wake (called the Von

Karman Trail) which has a definite frequency based on the diameter of the well

and velocity of the fluid. It is important that the well have sufficient stiffness so

that the wake frequency will never equal the natural frequency of the well itself.

If the natural frequency of the well were to coincide with the wake frequency, the

well would vibrate to destruction and break off in the piping.

On the following pages, a recommended maximum velocity rating can be found

for every standard well length and material cataloged. To reduce the complexity

of presenting this information, the ratings given are based on operating temperatures

of 1000ºF for wells made of Carbon Steel (C-1018), A.I.S.I. 304 & A.I.S.I. 316.

Values for brass wells are based on 350ºF operation. Limits for Monel wells are

based on 900ºF service. Slightly higher velocity is possible at lower temperatures.

Where single values appear in the velocity tables, these may be considered

safe for water, steam, air or gas. In the shorter insertion lengths, consideration

is given to the velocity pressure effect of water flowing at higher velocities. The

values in parenthesis, therefore, represent safe values for water flow while the

unbracketted value may be used for steam, air, gas and similar density fluids.

It should be pointed out that the values given are extremely conservative, and

intended primarily as a guide. Wells are also safe if the resonant frequency is

below the wake frequency or if the fluid velocity is constantly fluctuating through

the critical velocity point. If the installation is not hampered by the use of a

sufficiently stiff well, we recommend the values given not be exceeded.

If you have operating conditions requiring special well designs, our Engineering

Staff is available to assist you.


A U B

1-1/2” -U 2-1/2 4 2-1/2Dia. -U 4-1/2 6 4-1/2385 -U 7-1/2 9 7-1/2

Weld-In -U10-1/2 12 10-1/2 .385-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 24 22-1/2

Application:260 weld-in series fits 1/4” diameter elements.385 weld-in series fits 3/8” diameter elements for weldingdirectly into piping.

Materials:Carbon Steel (C-1018 or A-105 as specified),304SS, 316SS, Chrome Moly (F-11 or F-22 as specified).Other materials are available.


Lagging Extension:Specify by adding “T” lagging to 1-3/4” head dimension.



1-1/2” Dia. Carbon Steel 451 269.0 96.9 49.0 29.9 20.0 14.0 10.7(286) (159)

385 A.I.S.I. 304 & 316 531 285.0 102.0 52.0 31.6 21.2 15.0 11.4(385) (220)

Weld-In F-11 or F-22 542 290.0 104.0 53.2 32.0 21.5 15.4 11.6(392) (224)



1-1/2” Dia. Carbon Steel 493 220.0 79.4 40.5 24.5 16.4 11.7 8.8(306) (170)

260 A.I.S.I. 304 & 316 539 233.5 84.0 42.8 25.9 17.3 12.4 9.3(443) (231)

Weld-In F-11 or F-22 549 237.0 85.5 43.0 26.4 17.6 12.6 9.5(451) (235)

Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


F-11 7350 7350 7350 7350 7350 2898 504F-22 7224 7224 7224 7224 7098 3192 546


Temperature - °F

Material 70° 200° 400° 600° 800° 1000° 1200°


F-11 6562 6562 6562 6562 6562 2587 450F-22 6450 6450 6450 6450 6337 2850 487


1-1/2” Diameter Weld-In Thermowells

Series 385Weld-In

Series 260Weld-In

260 and 385 Weld-In SeriesTo Order, Please Specify:


1-800-827-8240 19


A U B

1-1/2” -U 2-1/2 4 2-1/2Dia. -U 4-1/2 6 4-1/2260 -U 7-1/2 9 7-1/2

Weld-In -U10-1/2 12 10-1/2 .260-U13-1/2 15 13-1/2-U16-1/2 18 16-1/2-U22-1/2 24 22-1/2

Vel

ocity

Rat

ings

of

Wel

ls

6

A ELEMENT LENGTH

1/4

.260 BORE1-1/2 DIA.

1/2 NPSM

DIA.

U INSERTION LENGTH

1-1/2 DIA.


5/8

1-3/4

A ELEMENT LENGTH

1/4

.385 BORE1-1/2 DIA.

1/2 NPSM

DIA.

U INSERTION LENGTH

1-1/2 DIA.


49/64

1-3/4

A properly installed thermometer bulb will project into liquid an amount equal to

its sensitive length plus at least one inch. In air or gas, the bulb should be

immersed to its sensitive length plus at least three inches. Thermocouples and

thermistors have short sensitive lengths, therefore can use the smallest insertion

lengths. Bi-metal thermometers, resistance thermometers and liquid-in-glass

thermometers have bulbs with sensitive portions between one and two inches

long. Therefore, the minimum standard insertion length of 2 1/2” must be entirely

immersed in liquid for proper accuracy. Filled system thermometer bulbs may

have sensitive portions from one to several inches in length. Determine the

sensitive length of the bulb before choosing an insertion length. Above all - be

sure that dead length, ie. - that are required to pass thru walls, pipe fittings, etc.,

is taken into account when choosing the necessary well insertion length.

Bore Size - The Interchangeability FactorAlmost any installation uses several types of temperature measuring instruments.

The selection of a standard bore diameter can produce maximum flexibility within

the plant. The same well can accommodate either thermocouple, resistance

thermometer, bi-metal thermometer, or test thermometer. The bore size of wells

shown in this catalog cover the most commonly used temperature sensing

elements as follows:



Liquid-in-glass Test Thermometers (unarmored)




Liquid-in-glass Test Thermometers (armored)


Tapered or Straight Shank - The Velocity Rating FactorTapered shank wells provide greater stiffness for the same sensitivity. The higher

strength-to-weight ratio gives these wells a higher natural resonant frequency

than for an equivalent length straight shank well, permitting operation at higher

fluid velocities. Refer to “Velocity Ratings of Wells” on page 6.

Protection Tubes

260 Sanitary Series

Sanitary Type Thermowells

5

260 & 385 Sanitary SeriesTo Order, Please Specify:

1. 3/4”-260W or 385W2. “U” Dimension3. Material4. End Cap Size

20 1-800-827-8240

385 Sanitary Series

Protection tubes are available in various ID’s, OD’sand materials to suit your application.

Can be ordered with threaded or flanged processconnections.

ApplicationsOvensFurnacesOpen ContainersFluesDucts

ApplicationsFood & BeveragePharmaceuticals

Available with 1”, 1-1/2”, 2”, 3” and 4” #16 AMPend caps. Other sizes and styles available upon request.

Alloy has been granted authorization #747 forstamping the 3A symbol.


Q A U

260 -U 2-1/2 -- 4 2-1/2Sanitary -U 4-1/2 3/4 6 4-1/2

-U 7-1/2 “ 9 7-1/2-U10-1/2 “ 12 10-1/2-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2


Q A U

385 -U 2-1/2 49/64 4 2-1/2Sanitary -U 4-1/2 “ 6 4-1/2

-U 7-1/2 “ 9 7-1/2-U10-1/2 “ 12 10-1/2-U13-1/2 “ 15 13-1/2-U16-1/2 “ 18 16-1/2-U22-1/2 “ 24 22-1/2

Sele

ctio

n of

The

rmow

ells

A ELEMENT LENGTH


1.050

.385 BORE

49/64

1/4

A ELEMENT LENGTH

Q Dia.=3/4


1.050

.260 BORE

1/2 DIA.

2-1/2WELD

1/4

P NPT1/4O.D.

I.D.

UT

AS SPECIFIED

WELD

P NPT1/4O.D.

I.D.

Material - The Longevity FactorIn general, the thermowell material chosen for the installation is governed mainly

by the corrosion conditions the well will face. Recommended materials for various

services are given in the Corrosive Service Guide on page 23. The high polish

given to all stainless and monel wells provides maximum corrosion resistance

and strength. Occasionally, the material consideration is one of strength rather

than corrosion. For example, a stainless steel well may be required for high

pressure water service where otherwise a brass well would be satisfactory from

a corrosion standpoint. Consult the pressure-temperature ratings given for each

well type. The standard materials listed for each well series will cover most

requirements. Alloy carries a wide variety of special materials in inventory to

insure fast delivery of wells. Materials include special grades of Stainless Steel,

Chrome-molybdenum, Steel, Naval Brass, Hastelloy B&C, Nickel and Titanium.

Connection - The Installation FactorIn these pages you will find standardized wells of threaded, flanged (A.N.S.I. and

Van Stone) and socket weld types with standard bore sizes. Threaded wells are

all made in readily welded or brazed materials. This is important for installations

requiring seal welding or brazing. The pipe thread provides the mechanical

strength, the weld merely seals. Flanged wells (other than Van Stone type) consist

of a bar stock well which is solidly welded to a top quality flange. Standard

construction uses a primary “J” groove weld and a bevel groove secondary weld.

Both welds are machined to produce a clean fillet. This double welded construction

eliminates possibility of crevice corrosion and stress problems since no open

joints are exposed from either inside or outside the installation. Socket welding

types of wells are simple to install by merely welding into place. These wells fit

A.N.S.I. standard socket weld couplings or flanges. The resulting installation is

clean and tight.

Insertion Length - The Accuracy FactorThe distance from the end of the well to the underside of the thread, or other

connection means, (designated as “U”) is the insertion length. For best accuracy,

this length should be long enough to permit the entire temperature sensitive part

of the thermometer bulb to project into the temperature medium being measured.

Sele

ctio

n of

The

rmow

ells

Tantalum Jackets

1-800-827-8240 214

Teflon ThermowellsCoatedPFA Teflon coating applied .008” to .010” thick. Other coatingsavailable upon request.

Teflon’s ability to tolerate harsh chemical environments makethese wells ideal for use in highly corrosive applications.

SolidAvailable with 1/2”, 3/4” and 1” NPT process connection anda maximum overall length of 12-1/4”.

Solid Teflon thermowells are ideal for measuring temperaturein acid solutions or other caustic environments where thetemperature is under 400 deg. F at atmospheric pressure.

Not available in flanged configuration.

Tantalum jackets cover insertion length and raised facearea of flange. Used in applications where corrosion resistanceis critical.

Standard thickness of jacket:.015” on “U” dimension, raised face and end plug..030” thick jackets available upon request.

Tantalum jackets are available in 1/2”, 3/4” and 7/8” IDsizes to fit 1”, 1-1/2”, 2”, 3” and 4” flanges.

Also available in Titanium and Zirconium with 3/4” OD.

To ensure proper fit, please order with thermowell.

ApplicationsChlorineBromineHydrochloricNitricSulfuric acids

ApplicationsAcids and causticsCorrosivesElectroplatingFood & BeveragePharmaceuticals


BORE

O.D.

U INSERTION LENGTH

WELD


TANTALUM JACKETCovering “U” Dimension andRaised Face Portionof Flange

1-1/4

2-1/4

1/2 NSPM

Expense connected with thermowell selection does not end with the initial

purchase. Listed below are some of the reasons for the careful dimensioning of

the Thermowells in this catalog. Note the emphasis on standardizing of bore size,

element (or stem) length and other internal dimensions. You will discover other

benefits to using standard wells as time goes on.

Save On Initial InvestmentStandard wells are produced on a large quantity basis bringing about reduced

cost and improved delivery. Temperature sensing elements are lower in cost

since you are buying larger quantities of particular sizes.

Gain Overall FlexibilityA temperature sensing element in a threaded well also fits a flanged well

downstream, or a socket weld well on main steam. Pull out a Bi-metal thermometer

and insert a test thermometer or thermocouple in that same well. Since these

wells accept several types of sensing elements, instruments may be “swapped

around” to suit changing optional procedures or advancing technology.

Reduce Spare Instrument InventoryUse of standard wells throughout the plant can reduce the number of spare

instruments necessary to insure safe coverage. Less work is required by the

power plant designer in establishing a recommended spare list.

Minimize Down TimeEven if caught without a spare, chances are that an instrument, in a less critical

location can immediately be relocated to a measurement point where a failure

has resulted.

Lengths:± 1/16” on length 12” or less

± 1/8” on length 12” or over

Wells 30” overall length and longer will be

drilled thru end, plugged and heliarc welded,

if solid bored is specified. Built-up design

must be specified beyond 42 1/4” overall

length.

O.D. Tolerances:Fractional: ± .015

Decimal: ± .005 on .000 place

± .010 on .00 place

Bore I.D. Tolerances:+ .005

- .003

End Thickness:Gun Drill Bottom

1/4” to bottom ± 1/16”, 3/16” min. end

Concentricity of Bore to O.D.:± 10% of min. wall thickness

Surface Finish:16-32 Ra Standard

4-12 Ra available at an extra charge.


Wetted surface finish of 80 Ra is available at

a savings on some wells.


Radius under Threads and Flanges:1/8” is standard, ± 1/16”

1/16” on Van Stones

Male Threads: (NPT)± 1 on thread gage

Female Threads:(1/2” NPSM) standard, 1/2” NPT available

upon request.

Go gage to 5/8” depth of thread

No go gage 2 turns max.

End of Wells:Break corners - No Burrs

Threaded WellsRound stock with wrench flats will be used if

hex stock is not available. Lagging extension

may be left as hex or as machined diameter.

Stamping:Material code identification and type of

material stamped on Hex or round facing

open end of well.

Flanged Wells:Made in accordance with ANSI B16.5.

Raised Face is serrated.

125 RMS Smooth Face must be specified on

order if needed.

Front “J”:Groove welds are 1/4” wide by 1/4” deep.

Welds are machined, leaving 1/8” radius.

Rear welds are 1/8” wide by 1/8” deep “V”.

Welds are machined, leaving 1/4 radius.

Full penetration welds are available upon

request. Must be specified.

Allo

y St

anda

rd M

anuf

actu

ring

Tole

ranc

es

Why

Sta

ndar

d T

herm

owel

ls?

22 3

Versatility and PriceALLOY has the capabilities of meeting all of your Thermowell requirementswhether they be a single piece or very large contract jobs at a competitive price.

SalesALLOY maintains ample finished and semi-finished stock levels to serve distributors,located throughout the USA and Canada. An expedited delivery service is availableupon request.

EngineeringThis catalog gives complete engineering information for the proper selection ofStandardized Thermowells. ALLOY’s engineers are willing and able to help withany design problems.

Manufacturing EquipmentAll wells are machined from solid bar stock on the most modern numerical controlmachines. Bores are produced on deep hole gun drilling machines which producesmooth true holes accurately centered in the sensitive part of the well.

ServiceDedicated to the principle of service and high quality, Alloy Engineering Companyrepresents an unusual combination of Engineering and Manufacturing know-how, not stopping at thermowell manufacture, but carrying on into completefamiliarity with application and detailed knowledge of the instruments which usethermowells as a means of protection. Alloy has been manufacturing thermowellssince 1958 and is still the largest thermowell specialist. We reply to all inquirespromptly via return telephone, FAX, email or mail.

SpecializationSince 1958, our company has specialized in the manufacture of thermowells forall kinds and makes of thermometers and temperature sensing elements. Thistype of specialization means intensive concentration on the problems of serviceand manufacture which brings about best possible delivery, lowest costs andhighest quality.

QualityWe take special pride in producing the finest thermowells ever made. Our Q.C.system and manual have been approved for government and nuclear service bythe major contractors. Wells made of corrosion resisting materials are highlypolished to assure maximum corrosion resistance. Our quality system meets therequirements of ISO 9002.

Material Selection/TraceabilityALLOY maintains an inventory of special alloys such as Titanium, Hastelloy B&C,Incoloy, 446SS, 410SS, Nickel, Monel, Inconel 600, Teflon, Aluminum, F-22,A-105, Bronze, etc., for prompt delivery.Throughout our entire manufacturing process the material is traceable to the MillTest Reports which are available upon request.Materials comply with ASTM and industry standards. Nuclear quality material isavailable upon request.Bar stock meets N.A.C.E. MR-01-75 specification. Flanged wells can be heattreated to comply with the N.A.C.E. specification.

A W

ord

Abo

ut A

lloy

Engi

neer

ing

Com

pany

Corrosive Service Guide To Materials

In recommending the above materials, consideration has been given to providing good service life without undue cost. Where two or more materials are satisfactory,the least expensive is listed. Consult the factory for information on materials or services not given.


Acetic Acid 212 All MonelAcetic Anhydride 300 NickelAcetone 212 All 304 SSAcetylene 400 304 SSAlcohols 212 All 304 SSAlum. (Potassium 300 All Hast. C or Sodium)Aluminum Chloride 212 All Hast. BAluminum Sulfate 212 All 316 SSAmmonia, Dry 212 All 304, 316 SSAmmonium Hydroxide 212 All 304, 316 SS (Ammonia, Aqua)Ammonium Chloride 300 50% MonelAmmonium Nitrate 300 All 304 SSAmmonium Sulfate 212 All 316 SSAmyl Acetate 300 All 304 SSAniline 75 MonelAsphalt 250 304 SSAtmosphere 304 SS (Industrial and Marine)Barium Compounds SEE CALCIUMBeer 70 304 SSBenzene (Benzol) 212 SteelBenzoic Acid 212 All 316 SSBleaching Powder 70 15% MonelBorax 212 All BrassBordeaux Mixture 200 304 SSBoric Acid 400 All 316 SSBromine 125 Dry MonelButane 400 All SteelButyl Alcohol SEE ALCOHOLSButyric Acid 212 Hast. CCalcium Bisulphite 75 All Hast. CCalcium Chloride 212 All Hast. CCalcium Hydroxide 300 20% Hast. CCalcium Hypochlorite SEE BLEACHING POWDER

Carbolic Acid SEE PHENOLCarbon Dioxide, Dry 800 All BrassCarbonated Water 212 All 304 SSCarbonated Beverages 212 304 SSCarbon Disulfide 200 304 SSCarbon Tetrachloride 125 All MonelChlorine, Dry 100 MonelChlorine, Moist 100 All MonelChloracetic Acid 212 All MonelChloroform, Dry 212 MonelChromic Acid 300 All Hast. CCider 300 All 304 SSCitric Acid 212 All Hast. CCopper (10) Chloride 212 All Hast. CCopper (10) Nitrate 300 All 316 SSCopper (10) Sulfate 300 All 316 SS


Copper Plating Solution 180 304 SS (Cyanide)Copper Plating Solution 75 304 SS (Acid)Corn Oil 200 304 SSCreosote 200 All 304 SSCrude Oil 300 MonelEthyl Acetate SEE LACQUER THINNEREthyl Chloride, Dry 500 SteelEthanol SEE ALCOHOLSEthylene Glycol 212 All 304 SS (Uninhibited)Ethylene Oxide 75 SteelFatty Acids 500 All 316 SSFerric Chloride 75 All Hast. CFerric Sulfate 300 All 304 SSFormaldehyde 212 40% 316 SSFormic Acid 300 All 316 SSFreon 300 SteelFluorine, Anhydrous 100 304 SSFurfural 450 316 SSGasoline 300 SteelGlucose 300 304 SSGlue ph 6-8 300 All 304 SSGlycerine 212 All BrassHydrobromic Acid 212 All Hast. CHydrochloric Acid 225 All Hast. B (37-38%)Hydrogen Chloride, Dry 500 304 SSHydrocyanic Acid 212 All 304 SSHydrofluoric Acid 212 60% MonelHydrogen Fluoride, Dry 175 SteelHydrofluogilicic Acid 212 40% MonelHydrogen Peroxide 125 10-100% 304 SSKerosene 300 All SteelLacquers & Thinners 300 All 304 SSLactic Acid 300 All 316 SSLime 212 All 316 SSLinseed Oil 75 SteelMagnesium Chloride 212 50% NickelMagnesium Hydroxide 75 All 304 SS (or Oxide)Magnesium Sulfate 212 40% 304 SSMercuric Chloride 75 10% Hast. CMercury 700 100% SteelMethylene Chloride 212 All 304 SSMethyl Chloride, Dry 75 SteelMilk, fresh or sour 180 304 SSMolasses SEE GLUCOSENatural Gas 70 304 SSNitric Acid 75 All 304 SSNitric Acid 110 All 316 SS


Oxygen 75 All SteelOleic Acid SEE FATTY ACIDSOxalic Acid 212 All MonelPhotographic Bleaching 100 All 304 SSPalmitic Acid SEE FATTY ACIDSPhosphoric Acid 212 All 316 SSPhenol 212 All 316 SSPotassium Compounds SEE SODIUM COMPOUNDS

Propane 300 SteelRosin 700 100% 316 SSSea Water 75 MonelSoap & Detergents 212 All 304 SSSodium Bicarbonate 212 20% 316 SSSodium Bisulphate 212 20% 304SSSodium Bisulphite 212 20% 304 SSSodium Carbinate 212 40% 316 SSSodium Chloride 300 30% MonelSodium Chromate 212 All 316 SSSalt or Brine SEE SODIUM CHLORIDESodium Cyanide 212 All 304 SSSodium Hydroxide 212 30% 316 SSSodium Hypochlorite 75 10% Hast. CSodium Nitrate 212 40% 304 SSSodium Nitrite 75 20% 316 SSSodium Phosphate 212 10% SteelSodium Silicate 212 10% SteelSodium Sulfate 212 30% 316 SSSodium Sulfide 212 10% 316 SSSodium Sulfite 212 30% 304 SSSodium Thiosulfate 212 All 304 SSSteam 304 SSStearic Acid SEE FATTY ACIDSSugar Solutions SEE GLUCOSESulfur 500 304 SSSulfur Chloride 75 Dry 316 SSSulfur Dioxide 500 Dry 316 SSSulfur Trioxide 500 Dry 316 SSSulfuric Acid 212 10% 316 SSSulfuric Acid 212 10-90% Hast. BSulfuric Acid 212 90-100% Hast. BSulfuric Acid, Fuming 175 Carp. 20Sulfurous Acid 75 20% 316 SSTitanium Tetrachloride 75 All 316 SSTannic Acid 75 40% Hast. BToluene 75 SteelTrichloracetic Acid 75 All Hast. BTrichlorethylene 300 Dry MonelTurpentine 75 316 SSVarnish 150 SteelZinc Chloride 212 All Hast. BZinc Sulfate 212 All 316 SS

2 23

ContentsOptional Services page 7





Socket Weld Series page 12

Heavy Duty Socket-Weld page 13

Flanged Series page 14

Tapered Flanged Series page 15

General Purpose Test page 16

Limited Space page 16

Industrial Thermowells page 17

Van Stone Thermowells page 18

1-1/2” Dia. Weld-In Series page 19

Sanitary Type Thermowells page 20

Protection Tubes page 20

Tantalum Jackets page 21

Teflon Thermowells page 21

Manufacturing Tolerances page 22

Corrosive Service Guide page 23

Date post:	30-Jul-2020
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

Method of Selection - Bay Port Valve · 2013-04-28 · Bar stock meets N.A.C.E. MR-01-75...

Documents