Oxford Plastic Systems LtdUnit T2, Enstone Business ParkEnstone, Chipping NortonOxfordshireOX7 4NPUnited Kingdom
Tel: +44 (0)1608 678888Fax: +44 (0)1608 678899
Email: [email protected]
EBY 04/2016
ROAD PLATES, DRIVEWAY BOARDS, PEDESTRIAN COVERS & KERB RAMPS
ROAD PLATE15/5 Road Plate is a lightweight and long lasting alternative to steel.
Road Plate is a modular system with individual units linked together.There’s no need for expensive specialist lifting equipment as the road plate weighs only 42kg and can be installed in minutes with a two man lift. No crane needed.
The anti-slip surface provides secure pedestrian access and the innovative flexible edge dampens any unwanted sounds. Road Plate is ideal in residential areas.
- Should be bolted for carriageway use.
Features
• Modular Composite Road Plate System
• Tested to a vehicle weight of 44tonnes over a 700mm trench
• Easy two man lift
• Moulded anti slip surface
• Drop pin feature increases the stability
• Heavy duty linking pieces lock the product together securely
• End sections should be bolted down
• Refurbishment service available
• Slows traffic for increased safety
• No need for expensive specialist lifting equipment
• Designed and manufactured in UK
• Patented product
02
03
Flexible Edge
The Road Plate has an integral flexible edge which is designed to minimise road noise
• Ends are made from a flexible PVC compound
• Helps reduce road noise
• Can compensate for cambers in the road
• Replacement parts available
Road Plate
Light, 2 man lift to deploy. Easy to store and transport. Robust and long lasting, polymer material does not rust or degrade.
Steel Plates
Heavy and difficult to manoeuvre – special lifting equipment required.
Safety Guidelines
• Maximum loading of 6000kg per Road Plate. This is the wheel loading of a 44 tonne vehicle
• Each Road Plate weighs approx. 42kg and should be lifted by 2 people
• Always check the condition of Road Plates prior to instalment. Do NOT use if damage is identifiable
Dismantling
• Remove the fixing bolts from the end sections
• Starting from one end lift the plates to disengage the linking system
• When removing plates check for any signs of damage and wear
• Stack securely for transportation and store in a safe environment
04
• Check for damage
• Check the trench width does not exceed 700mm
• Check the drop pins are in working order
• Make sure the plates are placed centrally over the trench
• Lock plates together with inbuilt steel linking pins
• Once all the plates are in place link the end plates
• End plates must be bolted to the ground by a minimum of 2 bolts
INSTALLATION GUIDE
700mm
Integral drop pins increase product stability. Always check the drop pins are in good working order
700mm MAX TRENCH SPAN 44T H.G.V.
02 0301
Easy two man lift Automatic drop pins for lateral Plates fit together securely with heavy
stability duty interlock
05
ROAD PLATE INNER
ROAD PLATE END
Product No 0830
Length, end to end 1500mm
Width 500mm
Weight 44kg
Number per pallet 20
Colour Yellow and Black
Product No 0814
Length, end to end 1500mm
Width 500mm
Weight 23kg
Number per pallet 20
Colour Yellow
TECHNICAL SPECIFICATION
500
1500
Flexible end sections225
75
END PLATE
500
05 0604
Locks securely into position using
bolted end sections and or Radlock
Rubberised End SectionTwo off per assembly Polyurethane/EPDM70-80 Shore Hardness
PINTwelve off per AssemblyZinc Plated Mild Steel
PIN BLOCKTwo off per Assembly
Two off tapped M8 holes eachend to attach to Trenchcover
Four recesses for steel plate to bolt Rubberised End Sections to Trenchcover using M8 bolts (Plates not shown)
43.0 47.0
Ø 37.0 Ø 47.0
LOWPRO 11/11 PEDESTRIAN COVER
The LowPro trench cover has an innovative Flexi-Edge system which greatly reduces trip hazards for pedestrians and helps to reduce any unwanted movement.
Features
• Conforms to National Grid Footway Board Specification T/SP/E/42
• Heavier than traditional trench covers thanks to its PVC anti slip edge
• Central section made from glass reinforced composite
• Very stable without bolting
• Takes up any cambers in the pavement
• Reduced trip hazard for pedestrians
• Covers a 700mm trench
• Supports a weight up to 500kg
• Shock resistant
• Can be personalised with corporate colour and logo
• Flexible edges can be replaced
• Designed and manufactured in UK
06
LOWPRO
Product No 0825
Length, end to end 1125mm
Width 1125mm
Weight 26kg
Number per pallet 30
Colour Yellow (standard), any other colours on request
TECHNICAL SPECIFICATION
Max Trench Width 700mm
Oxford Plastics Systems Ltd Enstone Business Park, Enstone, Oxfordshire, OX7 4NP Tel +44 (0)1608 678888 Fax +44 (0)1608 678899 email [email protected] www.oxfordplastics.com
Product Code: All dimensions in mm Do not scale from drawing Copyright 2010 Oxford Plastics Systems Ltd
Product title: Low-Pro
07
LOWPRO 15/10 DRIVEWAY BOARD & PEDESTRIAN COVER
The New Low Pro 15/10 uses our patented Flexi-edge system to greatly reduce trip hazards for pedestrians and to reduce unwanted movement. The product was commissioned by National Grid with a brief to design a board to support one wheel of a 3.5t vehicle over a 900mm span and to use the Low Pro technology. In most site configurations the product will not need to be fixed in place which reduces installation time and reduce costs of reinstatement. Reducing the need to use Steel plates in driveway applications. The increased loading and design also enables the product to be used in pedestrian applications that require a span up to 1200mm greatly improving the choices of product available for utilities and contractors alike who have been involved in the design process and given feedback throughout
Specification
• Conforms to National Grid Footway Board Specification T/SP/E/42
• Heavier than traditional trench covers thanks to its PVC anti slip edge and higher load rating
• Lighter than Steel Road Plates making it easier to manoeuvre and transport for driveway applications
• Central section made from glass reinforced composite
• Very stable without bolting (Does not need to be fixed in most applications)
• Can be bolted if site conditions are poor and Risk Assessment deems necessary (RAMS)
• Covers 900mm trench for 3.5t vehicles and 1200mm for pedestrians up to 400kg
• Gas Vents and Probe hole designed into product
• Shock Resistant
• Two person lift
• Can be personalised with corporate colour and logo
• Designed and manufactured in the UK
TECHNICAL SPECIFICATION
SAFE COVER 15/10
Product No 0815
Length 1500mm
Width 1000mm
Height 35mm
Weight 42-48kg
Number per pallet 20
Colour Yellow (standard), any other colours on request.
75
R85
3
6
75
7.5
5
8.5
30
33
2
5
25
10 rebar
Flexible edge adapts to ground contours
NEW! WITH LOWPRO
TECHNOLOGY
SUPAGRIP SAFEKERB RAMPThe SafeKerb Ramp provides a safe means for wheelchair and pushchair users to reach the next level when a footpath has been closed for street works.
It can also provide easy access for mobility scooters up to 350kg.
Features
• Complies and exceeds the ‘Wheel Chair Boarding Ramp Specification’, the ‘Safety at Street works, Code of Practice’ and the ‘Disability Discrimination Act’
• Effective anti-slip surface and raised sides
• Adapts to varying kerb or step heights (60mm to 160mm)
• Very stable without bolting
• Does not need to be fixed in most applications
• Can be bolted if site conditions are poor and Risk Assessment deems necessary
• Can be used as an access for wheelchairs, pushchairs and mobility scooters up to 350kg
• Made from High-density polyethylene (HDPE) and PVC
• 100% recyclable
• Compact stacking for easy transport & storage
SAFEKERB RAMP
Product No 0836
Length, end to end 1282mm
Length between side guards 1219mm
Width 760mm
Height Not relevant
Weight 10kg
Number per pallet 30
Colour Yellow
TECHNICAL SPECIFICATION
08
NEW! WITH LOWPRO
TECHNOLOGY
0
1219
74
1282 80
18
760
c Jedco Product Design for Oxford Plastics+44 (0)1932 852497 / info@jedco. co uk
NEW SAFEKERB
Do not scale All dimensions in millimetres
ASSEMBLY
Weight
Blow Mouldingat 2.5mm wall thickness5L = 4.75Kg
PVC Ends1.37L 2Kg each
Total Weight8.75Kg
09.06.15
09
SAFEKERB RAMPThe SafeKerb Ramp provides a safe means for wheelchair and pushchair users to reach the next level when a footpath has been closed for street works.
Features
• Complies and exceeds the ‘Wheel Chair Boarding Ramp Specification’, the ‘Safety at Street works, Code of Practice’ and the ‘Disability Discrimination Act’
• Effective anti-slip surface and raised sides
• Adapts to varying kerb or step heights (60mm to 160mm)
• Recommended to be bolted down for maximum stability and security
• Can be used as an access for wheelchairs, pushchairs and mobility scooters up to 250kg
• Made from High-density polyethylene (HDPE).
• 100% recyclable
• Compact stacking for easy transport & storage
SAFEKERB RAMP
Product No 0804
Length, end to end 1265mm
Length between side guards 1215mm
Width 747mm
Height 112mm
Weight 6kg
Number per pallet 20
Colour Yellow
TECHNICAL SPECIFICATION
1265
747
GRIP PATTERN
1215
112
4 FEATURES IN CORNER TO ENABLE BOLTING TO ROAD IF REQUIRED
60
160
140
4 FEATURES IN CORNER TO ENABLE BOLTING TO ROAD IF REQUIRED
SAFE COVER 12/8The Safe Cover 12/8 is a versatile safety cover that is rigid in construction, yet lightweight. This sturdy glass reinforced composite cover maintains performance in demanding situations.
Suitable for trenches up to 700mm wide.
Features
• Complies with the UK’s DETR ‘Safety at Street works and Road works Code of Practice’.
• Moulded from a single piece of glass reinforced composite.
• Slip resistant surface and chamfered edges to prevent tripping.
• Underside has ribbed framework for added strength.
• Can take the distributed weight of a vehicle of up to 2000kg.
• Can be embossed with company name or logo for corporate branding.
• Lighter than a steel cover.
• Stronger than a wooden plate.
• Designed and manufactured in UK.
10
SAFE COVER 12/8
Product No 0307
Length 1200mm
Width 800mm
Height 30mm
Weight 17.5kg
Number per pallet 30
Colour Yellow (standard), any other colours on request.
TECHNICAL SPECIFICATION Oxford Plastic Systems Ltd Enstone Business Park, Enstone, Oxfordshire, OX7 4NP, UK Tel: +44 (0)1608 678888 - Fax: +44 (0)1608 678899 email: [email protected] www.oxfordplastics.com
Product Code: O307 All dimensions in mm Do not scale from drawing © 2008 Oxford Plastics Systems Ltd
12/8 Safe Cover page 1
800
1200
30
Oxford Plastic Systems Ltd Enstone Business Park, Enstone, Oxfordshire, OX7 4NP, UK Tel: +44 (0)1608 678888 - Fax: +44 (0)1608 678899 email: [email protected] www.oxfordplastics.com
Product Code: O307 All dimensions in mm Do not scale from drawing © 2008 Oxford Plastics Systems Ltd
12/8 Safe Cover page 1
800
1200
30
11
SAFE COVER 16/12Designed primarily for use in street works, Safe Cover 16/12 is strong and secure. Safe Cover 16/12 can take a distributed weight of up to 2 tonne.
Features
• Complies with the UK’s DETR ‘Safety at Street works and Road works Code of Practice’.
• Moulded from a single piece of glass reinforced composite.
• Designed to cover trenches of a maximum width of 900mm.
• Slip resistant surface and chamfered edges to prevent tripping.
• Underside has ribbed framework for added strength.
• Can take the distributed weight of a vehicle of up to 2000kg.
• Can be embossed with company name or logo for corporate branding.
• Wide design suitable for driveway access.
• Lighter than a steel cover.
• Stronger than a wooden plate.
• Designed and manufactured in UK.
SAFE COVER 16/12
Product No 0820
Length - end to end 1600mm
Width 1200mm
Height 25mm
Weight 33kg
Number per pallet 25
Colour Yellow (standard), any other colours on request.
TECHNICAL SPECIFICATION Oxford Plastic Systems Ltd Enstone Business Park, Enstone, Oxfordshire, OX7 4NP, UK Tel: +44 (0)1608 678888 - Fax: +44 (0)1608 678899 email: [email protected] www.oxfordplastics.com
Product Code: 0820 All dimensions in mm Do not scale from drawing © 2008 Oxford Plastics Systems Ltd
16/12 Footway Board page 1
1200
1600
Max Weight 500kg
MAXIMUM TRENCH WIDTH 900mm
WWW.OXFORDPLASTICS.COM
SAFECOVER 1612
MAXIMUM TRENCH WIDTH 900mm
MA
XIM
UM
TR
ENC
H W
IDTH
900
mm
MA
XIMU
M TR
ENC
H W
IDTH
900mm
TWO MAN LIFT TWO MAN LIFT
26
Oxford Plastic Systems Ltd Enstone Business Park, Enstone, Oxfordshire, OX7 4NP, UK Tel: +44 (0)1608 678888 - Fax: +44 (0)1608 678899 email: [email protected] www.oxfordplastics.com
Product Code: 0820 All dimensions in mm Do not scale from drawing © 2008 Oxford Plastics Systems Ltd
16/12 Footway Board page 1
1200
1600
Max Weight 500kg
MAXIMUM TRENCH WIDTH 900mm
WWW.OXFORDPLASTICS.COM
SAFECOVER 1612
MAXIMUM TRENCH WIDTH 900mm
MA
XIM
UM
TR
ENC
H W
IDTH
900
mm
MA
XIMU
M TR
ENC
H W
IDTH
900mm
TWO MAN LIFT TWO MAN LIFT
26
